diff options
Diffstat (limited to 'doc')
| -rw-r--r-- | doc/README.fsl-ddr | 150 |
1 files changed, 150 insertions, 0 deletions
diff --git a/doc/README.fsl-ddr b/doc/README.fsl-ddr index abfb7f1..1d50153 100644 --- a/doc/README.fsl-ddr +++ b/doc/README.fsl-ddr @@ -222,3 +222,153 @@ Single slot system Reference http://www.samsung.com/global/business/semiconductor/products/dram/downloads/applicationnote/ddr2_odt_control_200603.pdf + +Interactive DDR debugging +=========================== + +For DDR parameter tuning up and debugging, the interactive DDR debugging can +be activated by saving an environment variable "ddr_interactive". The value +doesn't matter. Once activated, U-boot prompts "FSL DDR>" before enabling DDR +controller. The available commands can be seen by typing "help". + +The example flow of using interactive debugging is +type command "compute" to calculate the parameters from the default +type command "print" with arguments to show SPD, options, registers +type command "edit" with arguments to change any if desired +type command "go" to continue calculation and enable DDR controller +type command "reset" to reset the board +type command "recompute" to reload SPD and start over + +Note, check "next_step" to show the flow. For example, after edit opts, the +next_step is STEP_ASSIGN_ADDRESSES. After editing registers, the next_step is +STEP_PROGRAM_REGS. Upon issuing command "go", DDR controller will be enabled +with current setting without further calculation. + +The detail syntax for each commands are + +print [c<n>] [d<n>] [spd] [dimmparms] [commonparms] [opts] [addresses] [regs] + c<n> - the controller number, eg. c0, c1 + d<n> - the DIMM number, eg. d0, d1 + spd - print SPD data + dimmparms - DIMM paramaters, calcualted from SPD + commonparms - lowest common parameters for all DIMMs + opts - options + addresses - address assignment (not implemented yet) + regs - controller registers + +edit <c#> <d#> <spd|dimmparms|commonparms|opts|addresses|regs> <element> <value> + c<n> - the controller number, eg. c0, c1 + d<n> - the DIMM number, eg. d0, d1 + spd - print SPD data + dimmparms - DIMM paramaters, calcualted from SPD + commonparms - lowest common parameters for all DIMMs + opts - options + addresses - address assignment (not implemented yet) + regs - controller registers + <element> - name of the modified element + byte number if the object is SPD + <value> - decimal or heximal (prefixed with 0x) numbers + +reset + no arguement - reset the board + +recompute + no argument - reload SPD and start over + +compute + no argument - recompute from current next_step + +next_step + no argument - show current next_step + +help + no argument - print a list of all commands + +go + no argument - program memory controller(s) and continue with U-boot + +Examples of debugging flow + + FSL DDR>compute + Detected UDIMM UG51U6400N8SU-ACF + SL DDR>print + print [c<n>] [d<n>] [spd] [dimmparms] [commonparms] [opts] [addresses] [regs] + FSL DDR>print dimmparms + DIMM parameters: Controller=0 DIMM=0 + DIMM organization parameters: + module part name = UG51U6400N8SU-ACF + rank_density = 2147483648 bytes (2048 megabytes) + capacity = 4294967296 bytes (4096 megabytes) + burst_lengths_bitmask = 0C + base_addresss = 0 (00000000 00000000) + n_ranks = 2 + data_width = 64 + primary_sdram_width = 64 + ec_sdram_width = 0 + registered_dimm = 0 + n_row_addr = 15 + n_col_addr = 10 + edc_config = 0 + n_banks_per_sdram_device = 8 + tCKmin_X_ps = 1500 + tCKmin_X_minus_1_ps = 0 + tCKmin_X_minus_2_ps = 0 + tCKmax_ps = 0 + caslat_X = 960 + tAA_ps = 13125 + caslat_X_minus_1 = 0 + caslat_X_minus_2 = 0 + caslat_lowest_derated = 0 + tRCD_ps = 13125 + tRP_ps = 13125 + tRAS_ps = 36000 + tWR_ps = 15000 + tWTR_ps = 7500 + tRFC_ps = 160000 + tRRD_ps = 6000 + tRC_ps = 49125 + refresh_rate_ps = 7800000 + tIS_ps = 0 + tIH_ps = 0 + tDS_ps = 0 + tDH_ps = 0 + tRTP_ps = 7500 + tDQSQ_max_ps = 0 + tQHS_ps = 0 + FSL DDR>edit c0 opts ECC_mode 0 + FSL DDR>edit c0 regs cs0_bnds 0x000000FF + FSL DDR>go + 2 GiB left unmapped + 4 GiB (DDR3, 64-bit, CL=9, ECC off) + DDR Chip-Select Interleaving Mode: CS0+CS1 + Testing 0x00000000 - 0x7fffffff + Testing 0x80000000 - 0xffffffff + Remap DDR 2 GiB left unmapped + + POST memory PASSED + Flash: 128 MiB + L2: 128 KB enabled + Corenet Platform Cache: 1024 KB enabled + SERDES: timeout resetting bank 3 + SRIO1: disabled + SRIO2: disabled + MMC: FSL_ESDHC: 0 + EEPROM: Invalid ID (ff ff ff ff) + PCIe1: disabled + PCIe2: Root Complex, x1, regs @ 0xfe201000 + 01:00.0 - 8086:10d3 - Network controller + PCIe2: Bus 00 - 01 + PCIe3: disabled + In: serial + Out: serial + Err: serial + Net: Initializing Fman + Fman1: Uploading microcode version 101.8.0 + e1000: 00:1b:21:81:d2:e0 + FM1@DTSEC1, FM1@DTSEC2, FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5, e1000#0 [PRIME] + Warning: e1000#0 MAC addresses don't match: + Address in SROM is 00:1b:21:81:d2:e0 + Address in environment is 00:e0:0c:00:ea:05 + + Hit any key to stop autoboot: 0 + => |