summaryrefslogtreecommitdiff
path: root/doc
diff options
context:
space:
mode:
Diffstat (limited to 'doc')
-rw-r--r--doc/README.AVR32-port-muxing208
1 files changed, 208 insertions, 0 deletions
diff --git a/doc/README.AVR32-port-muxing b/doc/README.AVR32-port-muxing
new file mode 100644
index 0000000..b53799d
--- /dev/null
+++ b/doc/README.AVR32-port-muxing
@@ -0,0 +1,208 @@
+AVR32 Port multiplexer configuration
+====================================
+
+On AVR32 chips, most external I/O pins are routed through a port
+multiplexer. There are currently two kinds of port multiplexer
+hardware around with different register interfaces:
+
+ * PIO (AT32AP700x; this is also used on ARM AT91 chips)
+ * GPIO (all other AVR32 chips)
+
+The "PIO" variant supports multiplexing up to two peripherals per pin
+in addition to GPIO (software control). Each pin has configurable
+pull-up, glitch filter, interrupt and multi-drive capabilities.
+
+The "GPIO" variant supports multiplexing up to four peripherals per
+pin in addition to GPIO. Each pin has configurable
+pull-up/pull-down/buskeeper, glitch filter, interrupt, open-drain and
+schmitt-trigger capabilities, as well as configurable drive strength
+and slew rate control.
+
+Both controllers are configured using the same API, but the functions
+may accept different values for some parameters depending on the
+actual portmux implementation, and some parameters may be ignored by
+one of the implementation (e.g. the "PIO" implementation will ignore
+the drive strength flags since the hardware doesn't support
+configurable drive strength.)
+
+Selecting the portmux implementation
+------------------------------------
+Since u-boot is lacking a Kconfig-style configuration engine, the
+portmux implementation must be selected manually by defining one of
+the following symbols:
+
+ CONFIG_PORTMUX_PIO
+ CONFIG_PORTMUX_GPIO
+
+depending on which implementation the chip in question uses.
+
+Identifying pins
+----------------
+The portmux configuration functions described below identify the pins
+to act on based on two parameters: A "port" (i.e. a block of pins
+that somehow belong together) and a pin mask. Both are defined in an
+implementation-specific manner.
+
+The available ports are defined on the form
+
+ #define PORTMUX_PORT_A (something)
+
+where "A" matches the identifier given in the chip's data sheet, and
+"something" is whatever the portmux implementation needs to identify
+the port (usually a memory address).
+
+The pin mask is a bitmask where each '1' bit indicates a pin to apply
+the current operation to. The width of the bitmask may vary from port
+to port, but it is never wider than 32 bits (which is the width of
+'unsigned long' on avr32).
+
+Selecting functions
+-------------------
+Each pin can either be assigned to one of a predefined set of on-chip
+peripherals, or it can be set up to be controlled by software. For the
+former case, the portmux implementation defines an enum containing all
+the possible peripheral functions that can be selected. For example,
+the PIO implementation, which allows multiplexing two peripherals per
+pin, defines it like this:
+
+ enum portmux_function {
+ PORTMUX_FUNC_A,
+ PORTMUX_FUNC_B,
+ };
+
+To configure a set of pins to be connected to a given peripheral
+function, the following function is used.
+
+ void portmux_select_peripheral(void *port, unsigned long pin_mask,
+ enum portmux_function func, unsigned long flags);
+
+To configure a set of pins to be controlled by software (GPIO), the
+following function is used. In this case, no "function" argument is
+required since "GPIO" is a function in its own right.
+
+ void portmux_select_gpio(void *port, unsigned int pin_mask,
+ unsigned long flags);
+
+Both of these functions take a "flags" parameter which may be used to
+alter the default configuration of the pin. This is a bitmask of
+various flags defined in an implementation-specific way, but the names
+of the flags are the same on all implementations.
+
+ PORTMUX_DIR_OUTPUT
+ PORTMUX_DIR_INPUT
+
+These mutually-exlusive flags configure the initial direction of the
+pins. PORTMUX_DIR_OUTPUT means that the pins are driven by the CPU,
+while PORTMUX_DIR_INPUT means that the pins are tristated by the CPU.
+These flags are ignored by portmux_select_peripheral().
+
+ PORTMUX_INIT_HIGH
+ PORTMUX_INIT_LOW
+
+These mutually-exclusive flags configure the initial state of the
+pins: High (Vdd) or low (Vss). They are only effective when
+portmux_select_gpio() is called with the PORTMUX_DIR_OUTPUT flag set.
+
+ PORTMUX_PULL_UP
+ PORTMUX_PULL_DOWN
+ PORTMUX_BUSKEEPER
+
+These mutually-exclusive flags are used to enable any on-chip CMOS
+resistors connected to the pins. PORTMUX_PULL_UP causes the pins to be
+pulled up to Vdd, PORTMUX_PULL_DOWN causes the pins to be pulled down
+to Vss, and PORTMUX_BUSKEEPER will keep the pins in whatever state
+they were left in by whatever was driving them last. If none of the
+flags are specified, the pins are left floating if no one are driving
+them; this is only recommended for always-output pins (e.g. extern
+address and control lines driven by the CPU.)
+
+Note that the "PIO" implementation will silently ignore the
+PORTMUX_PULL_DOWN flag and interpret PORTMUX_BUSKEEPER as
+PORTMUX_PULL_UP.
+
+ PORTMUX_DRIVE_MIN
+ PORTMUX_DRIVE_LOW
+ PORTMUX_DRIVE_HIGH
+ PORTMUX_DRIVE_MAX
+
+These mutually-exlusive flags determine the drive strength of the
+pins. PORTMUX_DRIVE_MIN will give low power-consumption, but may cause
+corruption of high-speed signals. PORTMUX_DRIVE_MAX will give high
+power-consumption, but may be necessary on pins toggling at very high
+speeds. PORTMUX_DRIVE_LOW and PORTMUX_DRIVE_HIGH specify something in
+between the other two.
+
+Note that setting the drive strength too high may cause excessive
+overshoot and EMI problems, which may in turn cause signal corruption.
+Also note that the "PIO" implementation will silently ignore these
+flags.
+
+ PORTMUX_OPEN_DRAIN
+
+This flag will configure the pins as "open drain", i.e. setting the
+pin state to 0 will drive it low, while setting it to 1 will leave it
+floating (or, in most cases, let it be pulled high by an internal or
+external pull-up resistor.) In the data sheet for chips using the
+"PIO" variant, this mode is called "multi-driver".
+
+Enabling specific peripherals
+-----------------------------
+In addition to the above functions, each chip provides a set of
+functions for setting up the port multiplexer to use a given
+peripheral. The following are some of the functions available.
+
+All the functions below take a "drive_strength" parameter, which must
+be one of the PORTMUX_DRIVE_x flags specified above. Any other
+portmux flags will be silently filtered out.
+
+To set up the External Bus Interface (EBI), call
+
+ void portmux_enable_ebi(unsigned int bus_width,
+ unsigned long flags, unsigned long drive_strength)
+
+where "bus_width" must be either 16 or 32. "flags" can be any
+combination of the following flags.
+
+ PORTMUX_EBI_CS(x) /* Enable chip select x */
+ PORTMUX_EBI_NAND /* Enable NAND flash interface */
+ PORTMUX_EBI_CF(x) /* Enable CompactFlash interface x */
+ PORTMUX_EBI_NWAIT /* Enable NWAIT signal */
+
+To set up a USART, call
+
+ void portmux_enable_usartX(unsigned long drive_strength);
+
+where X is replaced by the USART instance to be configured.
+
+To set up an ethernet MAC:
+
+ void portmux_enable_macbX(unsigned long flags,
+ unsigned long drive_strength);
+
+where X is replaced by the MACB instance to be configured. "flags" can
+be any combination of the following flags.
+
+ PORTMUX_MACB_RMII /* Just set up the RMII interface */
+ PORTMUX_MACB_MII /* Set up full MII interface */
+ PORTMUX_MACB_SPEED /* Enable the SPEED pin */
+
+To set up the MMC controller:
+
+ void portmux_enable_mmci(unsigned long slot, unsigned long flags
+ unsigned long drive_strength);
+
+where "slot" identifies which of the alternative SD card slots to
+enable. "flags" can be any combination of the following flags:
+
+ PORTMUX_MMCI_4BIT /* Enable 4-bit SD card interface */
+ PORTMUX_MMCI_8BIT /* Enable 8-bit MMC+ interface */
+ PORTMUX_MMCI_EXT_PULLUP /* Board has external pull-ups */
+
+To set up a SPI controller:
+
+ void portmux_enable_spiX(unsigned long cs_mask,
+ unsigned long drive_strength);
+
+where X is replaced by the SPI instance to be configured. "cs_mask" is
+a 4-bit bitmask specifying which of the four standard chip select
+lines to set up as GPIOs.