diff options
Diffstat (limited to 'doc/device-tree-bindings')
| -rw-r--r-- | doc/device-tree-bindings/net/fsl-tsec-phy.txt | 64 | ||||
| -rw-r--r-- | doc/device-tree-bindings/net/micrel-ksz90x1.txt | 165 |
2 files changed, 229 insertions, 0 deletions
diff --git a/doc/device-tree-bindings/net/fsl-tsec-phy.txt b/doc/device-tree-bindings/net/fsl-tsec-phy.txt new file mode 100644 index 0000000..c5bf48c --- /dev/null +++ b/doc/device-tree-bindings/net/fsl-tsec-phy.txt @@ -0,0 +1,64 @@ +* TSEC-compatible ethernet nodes + +Properties: + + - compatible : Should be "fsl,tsec" + - reg : Offset and length of the register set for the device + - phy-handle : See ethernet.txt file in the same directory. + - phy-connection-type : See ethernet.txt file in the same directory. This + property is only really needed if the connection is of type "rgmii-id", + "rgmii-rxid" and "rgmii-txid" as all other connection types are detected + by hardware. + +Example: + ethernet@24000 { + compatible = "fsl,tsec"; + reg = <0x24000 0x1000>; + phy-handle = <&phy0>; + phy-connection-type = "sgmii"; + }; + +Child nodes of the TSEC controller are typically the individual PHY devices +connected via the MDIO bus (sometimes the MDIO bus controller is separate). + +* MDIO IO device + +The MDIO is a bus to which the PHY devices are connected. For each +device that exists on this bus, a PHY node should be created. + +Required properties: + - compatible : Should define the compatible device type for the + mdio. Currently supported string/device is "fsl,tsec-mdio". + - reg : Offset and length of the register set for the device + +Example: + + mdio@24520 { + compatible = "fsl,tsec-mdio"; + reg = <0x24520 0x20>; + + ethernet-phy@0 { + reg = <0>; + }; + }; + +* TBI Internal MDIO bus + +As of this writing, every tsec is associated with an internal TBI PHY. +This PHY is accessed through the local MDIO bus. These buses are defined +similarly to the mdio buses. The TBI PHYs underneath them are similar to +normal PHYs, but the reg property is considered instructive, rather than +descriptive. The reg property should be chosen so it doesn't interfere +with other PHYs on the bus. The TBI PHYs are referred to by a "tbi-handle" +property under the tsec node, which has a similar meaning of "phy-handle". + +Example: + ethernet@24000 { + phy-handle = <&tbi1>; + }; + + mdio@24520 { + tbi1: tbi-phy@1f { + reg = <0x1f>; + }; + }; diff --git a/doc/device-tree-bindings/net/micrel-ksz90x1.txt b/doc/device-tree-bindings/net/micrel-ksz90x1.txt new file mode 100644 index 0000000..307f53f --- /dev/null +++ b/doc/device-tree-bindings/net/micrel-ksz90x1.txt @@ -0,0 +1,165 @@ +Micrel KSZ9021/KSZ9031 Gigabit Ethernet PHY + +Some boards require special tuning values, particularly when it comes to +clock delays. You can specify clock delay values by adding +micrel-specific properties to an Ethernet OF device node. + +Note that these settings are applied after any phy-specific fixup from +phy_fixup_list (see phy_init_hw() from drivers/net/phy/phy_device.c), +and therefore may overwrite them. + +KSZ9021: + + All skew control options are specified in picoseconds. The minimum + value is 0, the maximum value is 1800, and it is incremented by 120ps + steps. + + Optional properties: + + - rxc-skew-ps : Skew control of RXC pad + - rxdv-skew-ps : Skew control of RX CTL pad + - txc-skew-ps : Skew control of TXC pad + - txen-skew-ps : Skew control of TX CTL pad + - rxd0-skew-ps : Skew control of RX data 0 pad + - rxd1-skew-ps : Skew control of RX data 1 pad + - rxd2-skew-ps : Skew control of RX data 2 pad + - rxd3-skew-ps : Skew control of RX data 3 pad + - txd0-skew-ps : Skew control of TX data 0 pad + - txd1-skew-ps : Skew control of TX data 1 pad + - txd2-skew-ps : Skew control of TX data 2 pad + - txd3-skew-ps : Skew control of TX data 3 pad + +KSZ9031: + + All skew control options are specified in picoseconds. The minimum + value is 0, and the maximum is property-dependent. The increment + step is 60ps. + + The KSZ9031 hardware supports a range of skew values from negative to + positive, where the specific range is property dependent. All values + specified in the devicetree are offset by the minimum value so they + can be represented as positive integers in the devicetree since it's + difficult to represent a negative number in the devictree. + + The following 5-bit values table apply to rxc-skew-ps and txc-skew-ps. + + Pad Skew Value Delay (ps) Devicetree Value + ------------------------------------------------------ + 0_0000 -900ps 0 + 0_0001 -840ps 60 + 0_0010 -780ps 120 + 0_0011 -720ps 180 + 0_0100 -660ps 240 + 0_0101 -600ps 300 + 0_0110 -540ps 360 + 0_0111 -480ps 420 + 0_1000 -420ps 480 + 0_1001 -360ps 540 + 0_1010 -300ps 600 + 0_1011 -240ps 660 + 0_1100 -180ps 720 + 0_1101 -120ps 780 + 0_1110 -60ps 840 + 0_1111 0ps 900 + 1_0000 60ps 960 + 1_0001 120ps 1020 + 1_0010 180ps 1080 + 1_0011 240ps 1140 + 1_0100 300ps 1200 + 1_0101 360ps 1260 + 1_0110 420ps 1320 + 1_0111 480ps 1380 + 1_1000 540ps 1440 + 1_1001 600ps 1500 + 1_1010 660ps 1560 + 1_1011 720ps 1620 + 1_1100 780ps 1680 + 1_1101 840ps 1740 + 1_1110 900ps 1800 + 1_1111 960ps 1860 + + The following 4-bit values table apply to the txdX-skew-ps, rxdX-skew-ps + data pads, and the rxdv-skew-ps, txen-skew-ps control pads. + + Pad Skew Value Delay (ps) Devicetree Value + ------------------------------------------------------ + 0000 -420ps 0 + 0001 -360ps 60 + 0010 -300ps 120 + 0011 -240ps 180 + 0100 -180ps 240 + 0101 -120ps 300 + 0110 -60ps 360 + 0111 0ps 420 + 1000 60ps 480 + 1001 120ps 540 + 1010 180ps 600 + 1011 240ps 660 + 1100 300ps 720 + 1101 360ps 780 + 1110 420ps 840 + 1111 480ps 900 + + Optional properties: + + Maximum value of 1860: + + - rxc-skew-ps : Skew control of RX clock pad + - txc-skew-ps : Skew control of TX clock pad + + Maximum value of 900: + + - rxdv-skew-ps : Skew control of RX CTL pad + - txen-skew-ps : Skew control of TX CTL pad + - rxd0-skew-ps : Skew control of RX data 0 pad + - rxd1-skew-ps : Skew control of RX data 1 pad + - rxd2-skew-ps : Skew control of RX data 2 pad + - rxd3-skew-ps : Skew control of RX data 3 pad + - txd0-skew-ps : Skew control of TX data 0 pad + - txd1-skew-ps : Skew control of TX data 1 pad + - txd2-skew-ps : Skew control of TX data 2 pad + - txd3-skew-ps : Skew control of TX data 3 pad + +Examples: + + /* Attach to an Ethernet device with autodetected PHY */ + &enet { + rxc-skew-ps = <1800>; + rxdv-skew-ps = <0>; + txc-skew-ps = <1800>; + txen-skew-ps = <0>; + status = "okay"; + }; + + /* Attach to an explicitly-specified PHY */ + mdio { + phy0: ethernet-phy@0 { + rxc-skew-ps = <1800>; + rxdv-skew-ps = <0>; + txc-skew-ps = <1800>; + txen-skew-ps = <0>; + reg = <0>; + }; + }; + ethernet@70000 { + status = "okay"; + phy = <&phy0>; + phy-mode = "rgmii-id"; + }; + +References + + Micrel ksz9021rl/rn Data Sheet, Revision 1.2. Dated 2/13/2014. + http://www.micrel.com/_PDF/Ethernet/datasheets/ksz9021rl-rn_ds.pdf + + Micrel ksz9031rnx Data Sheet, Revision 2.1. Dated 11/20/2014. + http://www.micrel.com/_PDF/Ethernet/datasheets/KSZ9031RNX.pdf + +Notes: + + Note that a previous version of the Micrel ksz9021rl/rn Data Sheet + was missing extended register 106 (transmit data pad skews), and + incorrectly specified the ps per step as 200ps/step instead of + 120ps/step. The latest update to this document reflects the latest + revision of the Micrel specification even though usage in the kernel + still reflects that incorrect document. |