diff options
Diffstat (limited to 'doc/README.p3060qds')
| -rw-r--r-- | doc/README.p3060qds | 110 |
1 files changed, 0 insertions, 110 deletions
diff --git a/doc/README.p3060qds b/doc/README.p3060qds deleted file mode 100644 index ec62798..0000000 --- a/doc/README.p3060qds +++ /dev/null @@ -1,110 +0,0 @@ -Overview -========= -The P3060QDS is a Freescale reference board that hosts the six-core P3060 SOC. - -The P3060 Processor combines six e500mc Power Architecture processor -cores(1.2GHz) with high-performance datapath acceleration -architecture(DPAA), CoreNet fabric infrastructure, as well as network -and peripheral bus interfaces required for networking, telecom/datacom, -wireless infrastructure, and military/aerospace applications. - - -P3060QDS Board Specifications: -============================== -Memory subsystem: - * 2G Bytes UDIMM DDR3(64bit bus) with ECC on - * 128M Bytes NOR flash single-chip memory - * 16M Bytes SPI flash - * 8K Bytes AT24C64 I2C EEPROM for RCW - -Ethernet(Default SERDES 0x19): - * FM1-dTSEC1: connected to RGMII PHY1 (Vitesse VSC8641 on board,Bottom of dual RJ45) - * FM1-dTSEC2: connected to RGMII PHY2 (Vitesse VSC8641 on board,Top of dual RJ45) - * FM1-dTSEC3: connected to SGMII PHY (Vitesse VSC8234 port1 in slot1) - * FM1-dTSEC4: connected to SGMII PHY (Vitesse VSC8234 port3 in slot1) - * FM2-dTSEC1: connected to SGMII PHY (Vitesse VSC8234 port0 in slot2) - * FM2-dTSEC2: connected to SGMII PHY (Vitesse VSC8234 port2 in slot2) - * FM2-dTSEC3: connected to SGMII PHY (Vitesse VSC8234 port0 in slot1) - * FM2-dTSEC4: connected to SGMII PHY (Vitesse VSC8234 port2 in slot1) - -PCIe: - * PCIe1: Lanes A, B, C and D of Bank1 are connected to one x4 PCIe SLOT4 - * PCIe2: Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT3 - -RapidIO: - * sRIO1: Lanes E, F, G and H of Bank1 are connected to sRIO1 (SLOT3) - * sRIO2: Lanes A, B, C and D of Bank1 are connected to sRIO2 (SLOT4) - -USB: - * USB1: connected via an external ULPI PHY SMC3315 to a TYPE-A interface - * USB2: connected via an external ULPI PHY SMC3315 to a TYPE-AB interface - -I2C: - * I2C1_CH0: EEPROM AT24C64(0x50) RCW, AT24C02(0x51) DDR SPD, - AT24C02(0x53) DDR SPD, AT24C02(0x57) SystemID, RTC DS3232(0x68) - * I2C1_CH1: 1588 RiserCard(0x55), HSLB Testport, TempMon - ADT7461(0x4C), SerDesMux DS64MB201(0x51/59/5C/5D) - * I2C1_CH2: VDD/GVDD/GIDD ZL6100 (0x21/0x22/0x23/0x24/0x40) - * I2C1_CH3: OCM CFG AT24C02(0x55), OCM IPL AT24C64(0x56) - * I2C1_CH4: PCIe SLOT1 - * I2C1_CH5: PCIe SLOT2 - * I2C1_CH6: PCIe SLOT3 - * I2C1_CH7: PCIe SLOT4 - * I2C2: NULL - * I2C3: NULL - -UART: - * Supports two UARTs up to 115200 bps for console - - -Boot from NOR flash -=================== -1. Build image - export ARCH=powerpc - export CROSS_COMPILE=/your_path/gcc-4.5.xx-eglibc-2.11.xx/powerpc-linux-gnu/bin/powerpc-linux-gnu- - make P3060QDS_config - make - -2. Program image - => tftp 1000000 u-boot.bin - => protect off all - => erase eff80000 efffffff - => cp.b 1000000 eff80000 80000 - -3. Program RCW - => tftp 1000000 rcw.bin - => protect off all - => erase e8000000 e801ffff - => cp.b 1000000 e8000000 50 - -4. Program FMAN Firmware ucode - => tftp 1000000 ucode.bin - => protect off all - => erase ef000000 ef0fffff - => cp.b 1000000 ef000000 2000 - -5. Change DIP-switch - RCW Location: SW1[1-5] = 01101 (eLBC 16bit NOR flash) - Note: 1 stands for 'on', 0 stands for 'off' - - -Using the Device Tree Source File -================================= -To create the DTB (Device Tree Binary) image file, use a command -similar to this: - dtc -O dtb -b 0 -p 1024 p3060qds.dts > p3060qds.dtb - -Or use the following command: - {linux-2.6}/make p3060qds.dtb ARCH=powerpc - -then the dtb file will be generated under the following directory: - {linux-2.6}/arch/powerpc/boot/p3060qds.dtb - - -Booting Linux -============= -Place a linux uImage in the TFTP disk area. - tftp 1000000 uImage - tftp 2000000 rootfs.ext2.gz.uboot - tftp 3000000 p3060rdb.dtb - bootm 1000000 2000000 3000000 |