diff options
Diffstat (limited to 'doc/README.nand')
| -rw-r--r-- | doc/README.nand | 63 |
1 files changed, 63 insertions, 0 deletions
diff --git a/doc/README.nand b/doc/README.nand index 913e9b5..b91f198 100644 --- a/doc/README.nand +++ b/doc/README.nand @@ -104,6 +104,16 @@ Configuration Options: CONFIG_SYS_MAX_NAND_DEVICE The maximum number of NAND devices you want to support. + CONFIG_SYS_NAND_MAX_ECCPOS + If specified, overrides the maximum number of ECC bytes + supported. Useful for reducing image size, especially with SPL. + This must be at least 48 if nand_base.c is used. + + CONFIG_SYS_NAND_MAX_OOBFREE + If specified, overrides the maximum number of free OOB regions + supported. Useful for reducing image size, especially with SPL. + This must be at least 2 if nand_base.c is used. + CONFIG_SYS_NAND_MAX_CHIPS The maximum number of NAND chips per device to be supported. @@ -169,6 +179,59 @@ Configuration Options: Please convert your driver even if you don't need the extra flexibility, so that one day we can eliminate the old mechanism. + + CONFIG_SYS_NAND_ONFI_DETECTION + Enables detection of ONFI compliant devices during probe. + And fetching device parameters flashed on device, by parsing + ONFI parameter page. + + CONFIG_BCH + Enables software based BCH ECC algorithm present in lib/bch.c + This is used by SoC platforms which do not have built-in ELM + hardware engine required for BCH ECC correction. + + +Platform specific options +========================= + CONFIG_NAND_OMAP_GPMC + Enables omap_gpmc.c driver for OMAPx and AMxxxx platforms. + GPMC controller is used for parallel NAND flash devices, and can + do ECC calculation (not ECC error detection) for HAM1, BCH4, BCH8 + and BCH16 ECC algorithms. + + CONFIG_NAND_OMAP_ELM + Enables omap_elm.c driver for OMAPx and AMxxxx platforms. + ELM controller is used for ECC error detection (not ECC calculation) + of BCH4, BCH8 and BCH16 ECC algorithms. + Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine, + thus such SoC platforms need to depend on software library for ECC error + detection. However ECC calculation on such plaforms would still be + done by GPMC controller. + + CONFIG_NAND_OMAP_ECCSCHEME + On OMAP platforms, this CONFIG specifies NAND ECC scheme. + It can take following values: + OMAP_ECC_HAM1_CODE_SW + 1-bit Hamming code using software lib. + (for legacy devices only) + OMAP_ECC_HAM1_CODE_HW + 1-bit Hamming code using GPMC hardware. + (for legacy devices only) + OMAP_ECC_BCH4_CODE_HW_DETECTION_SW + 4-bit BCH code (unsupported) + OMAP_ECC_BCH4_CODE_HW + 4-bit BCH code (unsupported) + OMAP_ECC_BCH8_CODE_HW_DETECTION_SW + 8-bit BCH code with + - ecc calculation using GPMC hardware engine, + - error detection using software library. + - requires CONFIG_BCH to enable software BCH library + (For legacy device which do not have ELM h/w engine) + OMAP_ECC_BCH8_CODE_HW + 8-bit BCH code with + - ecc calculation using GPMC hardware engine, + - error detection using ELM hardware engine. + NOTE: ===== |