diff options
Diffstat (limited to 'doc/README.mpc8641hpcn')
| -rw-r--r-- | doc/README.mpc8641hpcn | 106 |
1 files changed, 66 insertions, 40 deletions
diff --git a/doc/README.mpc8641hpcn b/doc/README.mpc8641hpcn index 1c41d77..d8fe0a4 100644 --- a/doc/README.mpc8641hpcn +++ b/doc/README.mpc8641hpcn @@ -21,16 +21,16 @@ Jumpers: J14 Pins 1-2 (near plcc32 socket) Switches: - SW1(1-5) = 01100 CFG_COREPLL = 01000 :: CORE = 2:1 + SW1(1-5) = 01100 CONFIG_SYS_COREPLL = 01000 :: CORE = 2:1 01100 :: CORE = 2.5:1 10000 :: CORE = 3:1 11100 :: CORE = 3.5:1 10100 :: CORE = 4:1 01110 :: CORE = 4.5:1 - SW1(6-8) = 001 CFG_SYSCLK = 000 :: SYSCLK = 33MHz + SW1(6-8) = 001 CONFIG_SYS_SYSCLK = 000 :: SYSCLK = 33MHz 001 :: SYSCLK = 40MHz - SW2(1-4) = 1100 CFG_CCBPLL = 0010 :: 2X + SW2(1-4) = 1100 CONFIG_SYS_CCBPLL = 0010 :: 2X 0100 :: 4X 0110 :: 6X 1000 :: 8X @@ -38,34 +38,34 @@ Switches: 1100 :: 12X 1110 :: 14X 0000 :: 16X - SW2(5-8) = 1110 CFG_BOOTLOC = 1110 :: boot 16-bit localbus + SW2(5-8) = 1110 CONFIG_SYS_BOOTLOC = 1110 :: boot 16-bit localbus - SW3(1-7) = 0011000 CFG_VID = 0011000 :: VCORE = 1.2V + SW3(1-7) = 0011000 CONFIG_SYS_VID = 0011000 :: VCORE = 1.2V 0100000 :: VCORE = 1.11V SW3(8) = 0 VCC_PLAT = 0 :: VCC_PLAT = 1.2V 1 :: VCC_PLAT = 1.0V - SW4(1-2) = 11 CFG_HOSTMODE = 11 :: both prots host/root - SW4(3-4) = 11 CFG_BOOTSEQ = 11 :: no boot seq - SW4(5-8) = 0011 CFG_IOPORT = 0011 :: both PEX + SW4(1-2) = 11 CONFIG_SYS_HOSTMODE = 11 :: both prots host/root + SW4(3-4) = 11 CONFIG_SYS_BOOTSEQ = 11 :: no boot seq + SW4(5-8) = 0011 CONFIG_SYS_IOPORT = 0011 :: both PEX - SW5(1) = 1 CFG_FLASHMAP = 1 :: boot from flash + SW5(1) = 1 CONFIG_SYS_FLASHMAP = 1 :: boot from flash 0 :: boot from PromJet - SW5(2) = 1 CFG_FLASHBANK = 1 :: swap upper/lower + SW5(2) = 1 CONFIG_SYS_FLASHBANK = 1 :: swap upper/lower halves (virtual banks) 0 :: normal - SW5(3) = 0 CFG_FLASHWP = 0 :: not protected - SW5(4) = 0 CFG_PORTDIV = 1 :: 2:1 for PD4 + SW5(3) = 0 CONFIG_SYS_FLASHWP = 0 :: not protected + SW5(4) = 0 CONFIG_SYS_PORTDIV = 1 :: 2:1 for PD4 1:1 for PD6 - SW5(5-6) = 11 CFG_PIXISOPT = 11 :: s/w determined - SW5(7-8) = 11 CFG_LADOPT = 11 :: s/w determined + SW5(5-6) = 11 CONFIG_SYS_PIXISOPT = 11 :: s/w determined + SW5(7-8) = 11 CONFIG_SYS_LADOPT = 11 :: s/w determined - SW6(1) = 1 CFG_CPUBOOT = 1 :: no boot holdoff - SW6(2) = 1 CFG_BOOTADDR = 1 :: no traslation - SW6(3-5) = 000 CFG_REFCLKSEL = 000 :: 100MHZ - SW6(6) = 1 CFG_SERROM_ADDR= 1 :: - SW6(7) = 1 CFG_MEMDEBUG = 1 :: - SW6(8) = 1 CFG_DDRDEBUG = 1 :: + SW6(1) = 1 CONFIG_SYS_CPUBOOT = 1 :: no boot holdoff + SW6(2) = 1 CONFIG_SYS_BOOTADDR = 1 :: no traslation + SW6(3-5) = 000 CONFIG_SYS_REFCLKSEL = 000 :: 100MHZ + SW6(6) = 1 CONFIG_SYS_SERROM_ADDR= 1 :: + SW6(7) = 1 CONFIG_SYS_MEMDEBUG = 1 :: + SW6(8) = 1 CONFIG_SYS_DDRDEBUG = 1 :: SW8(1) = 1 ACZ_SYNC = 1 :: 48MHz on TP49 SW8(2) = 1 ACB_SYNC = 1 :: THRMTRIP disabled @@ -74,56 +74,82 @@ Switches: SW8(5) = 0 SUSLED = 0 :: SouthBridge Mode SW8(6) = 0 SPREAD = 0 :: REFCLK SSCG Disabled SW8(7) = 1 ACPWR = 1 :: non-battery - SW8(8) = 0 CFG_IDWP = 0 :: write enable + SW8(8) = 0 CONFIG_SYS_IDWP = 0 :: write enable 3. Flash U-Boot --------------- -The flash range 0xFF800000 to 0xFFFFFFFF can be divided into 2 halves. +The flash range 0xEF800000 to 0xEFFFFFFF can be divided into 2 halves. It is possible to use either half to boot using u-boot. Switch 5 bit 2 is used for this purpose. -0xFF800000 to 0xFFBFFFFF - 4MB -0xFFC00000 to 0xFFFFFFFF - 4MB -When this bit is 0, U-Boot is at 0xFFF00000. -When this bit is 1, U-Boot is at 0xFFB00000. +0xEF800000 to 0xEFBFFFFF - 4MB +0xEFC00000 to 0xEFFFFFFF - 4MB +When this bit is 0, U-Boot is at 0xEFF00000. +When this bit is 1, U-Boot is at 0xEFB00000. Use the above mentioned flash commands to program the other half, and use switch 5, bit 2 to alternate between the halves. Note: The booting -version of U-Boot will always be at 0xFFF00000. +version of U-Boot will always be at 0xEFF00000. -To Flash U-Boot into the booting bank (0xFFC00000 - 0xFFFFFFFF): +To Flash U-Boot into the booting bank (0xEFC00000 - 0xEFFFFFFF): tftp 1000000 u-boot.bin protect off all - erase fff00000 +$filesize - cp.b 1000000 fff00000 $filesize + erase eff00000 +$filesize + cp.b 1000000 eff00000 $filesize or use tftpflash command: run tftpflash -To Flash U-boot into the alternative bank (0xFF800000 - 0xFFBFFFFF): +To Flash U-boot into the alternative bank (0xEF800000 - 0xEFBFFFFF): tftp 1000000 u-boot.bin - erase ffb00000 +$filesize - cp.b 1000000 ffb00000 $filesize + erase efb00000 +$filesize + cp.b 1000000 efb00000 $filesize 4. Memory Map ------------- +NOTE: RIO and PCI are mutually exclusive, so they share an address + +For 32-bit u-boot, devices are mapped so that the virtual address == +the physical address, and the map looks liks this: Memory Range Device Size ------------ ------ ---- 0x0000_0000 0x7fff_ffff DDR 2G + 0x8000_0000 0x9fff_ffff RIO MEM 512M 0x8000_0000 0x9fff_ffff PCI1/PEX1 MEM 512M - 0xa000_0000 0xafff_ffff PCI2/PEX2 MEM 512M - 0xf800_0000 0xf80f_ffff CCSR 1M - 0xf810_0000 0xf81f_ffff PIXIS 1M + 0xa000_0000 0xbfff_ffff PCI2/PEX2 MEM 512M + 0xffe0_0000 0xffef_ffff CCSR 1M + 0xffdf_0000 0xffdf_7fff PIXIS 8K + 0xffdf_8000 0xffdf_ffff CF 8K 0xf840_0000 0xf840_3fff Stack space 32K - 0xe200_0000 0xe2ff_ffff PCI1/PEX1 IO 16M - 0xe300_0000 0xe3ff_ffff PCI2/PEX2 IO 16M - 0xfe00_0000 0xfeff_ffff Flash(alternate)16M - 0xff00_0000 0xffff_ffff Flash(boot bank)16M + 0xffc0_0000 0xffc0_ffff PCI1/PEX1 IO 64K + 0xffc1_0000 0xffc1_ffff PCI2/PEX2 IO 64K + 0xef80_0000 0xefff_ffff Flash 8M + +For 36-bit-enabled u-boot, the virtual map is the same as for 32-bit. +However, the physical map is altered to reside in 36-bit space, as follows. +Addresses are no longer mapped with VA == PA. All accesses from +software use the VA; the PA is only used for setting up windows +and mappings. Note that with the exception of PCI MEM and RIO, the low + 32 bits are the same as the VA above; only the top 4 bits vary: + + Memory Range Device Size + ------------ ------ ---- + 0x0_0000_0000 0x0_7fff_ffff DDR 2G + 0xc_0000_0000 0xc_1fff_ffff RIO MEM 512M + 0xc_0000_0000 0xc_1fff_ffff PCI1/PEX1 MEM 512M + 0xc_2000_0000 0xc_3fff_ffff PCI2/PEX2 MEM 512M + 0xf_ffe0_0000 0xf_ffef_ffff CCSR 1M + 0xf_ffdf_0000 0xf_ffdf_7fff PIXIS 8K + 0xf_ffdf_8000 0xf_ffdf_ffff CF 8K + 0x0_f840_0000 0xf_f840_3fff Stack space 32K + 0xf_ffc0_0000 0xf_ffc0_ffff PCI1/PEX1 IO 64K + 0xf_ffc1_0000 0xf_ffc1_ffff PCI2/PEX2 IO 64K + 0xf_ef80_0000 0xf_efff_ffff Flash 8M 5. pixis_reset command -------------------- |