diff options
Diffstat (limited to 'doc/README.m5475evb')
| -rw-r--r-- | doc/README.m5475evb | 54 |
1 files changed, 27 insertions, 27 deletions
diff --git a/doc/README.m5475evb b/doc/README.m5475evb index 37d1438..dc9a605 100644 --- a/doc/README.m5475evb +++ b/doc/README.m5475evb @@ -74,20 +74,20 @@ CONFIG_M547x -- define for all Freescale MCF547x CPUs CONFIG_M5475 -- define for M5475EVB board CONFIG_MCFUART -- define to use common CF Uart driver -CFG_UART_PORT -- define UART port number, start with 0, 1 and 2 +CONFIG_SYS_UART_PORT -- define UART port number, start with 0, 1 and 2 CONFIG_BAUDRATE -- define UART baudrate CONFIG_FSLDMAFEC -- define to use common dma FEC driver CONFIG_NET_MULTI -- define to use multi FEC in u-boot CONFIG_MII -- enable to use MII driver CONFIG_CF_DOMII -- enable to use MII feature in cmd_mii.c -CFG_DISCOVER_PHY -- enable PHY discovery -CFG_RX_ETH_BUFFER -- Set FEC Receive buffer -CFG_FAULT_ECHO_LINK_DOWN-- -CFG_FEC0_PINMUX -- Set FEC0 Pin configuration -CFG_FEC1_PINMUX -- Set FEC1 Pin configuration -CFG_FEC0_MIIBASE -- Set FEC0 MII base register -CFG_FEC1_MIIBASE -- Set FEC0 MII base register +CONFIG_SYS_DISCOVER_PHY -- enable PHY discovery +CONFIG_SYS_RX_ETH_BUFFER -- Set FEC Receive buffer +CONFIG_SYS_FAULT_ECHO_LINK_DOWN-- +CONFIG_SYS_FEC0_PINMUX -- Set FEC0 Pin configuration +CONFIG_SYS_FEC1_PINMUX -- Set FEC1 Pin configuration +CONFIG_SYS_FEC0_MIIBASE -- Set FEC0 MII base register +CONFIG_SYS_FEC1_MIIBASE -- Set FEC0 MII base register MCFFEC_TOUT_LOOP -- set FEC timeout loop CONFIG_HAS_ETH1 -- define to enable second FEC in u-boot @@ -101,35 +101,35 @@ CONFIG_SLTTMR -- define to use SLT timer CONFIG_FSL_I2C -- define to use FSL common I2C driver CONFIG_HARD_I2C -- define for I2C hardware support CONFIG_SOFT_I2C -- define for I2C bit-banged -CFG_I2C_SPEED -- define for I2C speed -CFG_I2C_SLAVE -- define for I2C slave address -CFG_I2C_OFFSET -- define for I2C base address offset -CFG_IMMR -- define for MBAR offset +CONFIG_SYS_I2C_SPEED -- define for I2C speed +CONFIG_SYS_I2C_SLAVE -- define for I2C slave address +CONFIG_SYS_I2C_OFFSET -- define for I2C base address offset +CONFIG_SYS_IMMR -- define for MBAR offset CONFIG_PCI -- define for PCI support CONFIG_PCI_PNP -- define for Plug n play support CONFIG_SKIPPCI_HOSTBRIDGE -- SKIP PCI Host bridge -CFG_PCI_MEM_BUS -- PCI memory logical offset -CFG_PCI_MEM_PHYS -- PCI memory physical offset -CFG_PCI_MEM_SIZE -- PCI memory size -CFG_PCI_IO_BUS -- PCI IO logical offset -CFG_PCI_IO_PHYS -- PCI IO physical offset -CFG_PCI_IO_SIZE -- PCI IO size -CFG_PCI_CFG_BUS -- PCI Configuration logical offset -CFG_PCI_CFG_PHYS -- PCI Configuration physical offset -CFG_PCI_CFG_SIZE -- PCI Configuration size +CONFIG_SYS_PCI_MEM_BUS -- PCI memory logical offset +CONFIG_SYS_PCI_MEM_PHYS -- PCI memory physical offset +CONFIG_SYS_PCI_MEM_SIZE -- PCI memory size +CONFIG_SYS_PCI_IO_BUS -- PCI IO logical offset +CONFIG_SYS_PCI_IO_PHYS -- PCI IO physical offset +CONFIG_SYS_PCI_IO_SIZE -- PCI IO size +CONFIG_SYS_PCI_CFG_BUS -- PCI Configuration logical offset +CONFIG_SYS_PCI_CFG_PHYS -- PCI Configuration physical offset +CONFIG_SYS_PCI_CFG_SIZE -- PCI Configuration size -CFG_MBAR -- define MBAR offset +CONFIG_SYS_MBAR -- define MBAR offset CONFIG_MONITOR_IS_IN_RAM -- Not support -CFG_INIT_RAM_ADDR -- defines the base address of the MCF547x internal SRAM +CONFIG_SYS_INIT_RAM_ADDR -- defines the base address of the MCF547x internal SRAM -CFG_CSn_BASE -- defines the Chip Select Base register -CFG_CSn_MASK -- defines the Chip Select Mask register -CFG_CSn_CTRL -- defines the Chip Select Control register +CONFIG_SYS_CSn_BASE -- defines the Chip Select Base register +CONFIG_SYS_CSn_MASK -- defines the Chip Select Mask register +CONFIG_SYS_CSn_CTRL -- defines the Chip Select Control register -CFG_SDRAM_BASE -- defines the DRAM Base +CONFIG_SYS_SDRAM_BASE -- defines the DRAM Base 2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL =========================================== |