summaryrefslogtreecommitdiff
path: root/cpu
diff options
context:
space:
mode:
Diffstat (limited to 'cpu')
-rw-r--r--cpu/mcf5227x/speed.c4
-rw-r--r--cpu/mcf523x/cpu_init.c4
-rw-r--r--cpu/mcf523x/speed.c4
-rw-r--r--cpu/mcf52x2/cpu_init.c12
-rw-r--r--cpu/mcf52x2/speed.c8
-rw-r--r--cpu/mcf532x/speed.c5
-rw-r--r--cpu/mcf5445x/speed.c4
-rw-r--r--cpu/mcf547x_8x/speed.c5
-rw-r--r--cpu/mpc512x/Makefile2
-rw-r--r--cpu/mpc512x/fec.c794
-rw-r--r--cpu/mpc512x/fec.h227
-rw-r--r--cpu/mpc5xxx/Makefile2
-rw-r--r--cpu/mpc5xxx/fec.c1067
-rw-r--r--cpu/mpc5xxx/fec.h286
-rw-r--r--cpu/mpc5xxx/sdma.h93
-rw-r--r--cpu/sh2/Makefile49
-rw-r--r--cpu/sh2/cache.c112
-rw-r--r--cpu/sh2/config.mk26
-rw-r--r--cpu/sh2/cpu.c98
-rw-r--r--cpu/sh2/interrupts.c39
-rw-r--r--cpu/sh2/start.S78
-rw-r--r--cpu/sh2/time.c111
-rw-r--r--cpu/sh2/watchdog.c33
23 files changed, 591 insertions, 2472 deletions
diff --git a/cpu/mcf5227x/speed.c b/cpu/mcf5227x/speed.c
index 78c946f..0baf9bc 100644
--- a/cpu/mcf5227x/speed.c
+++ b/cpu/mcf5227x/speed.c
@@ -116,5 +116,9 @@ int get_clocks(void)
gd->bus_clk = gd->flb_clk;
}
+#ifdef CONFIG_FSL_I2C
+ gd->i2c1_clk = gd->bus_clk;
+#endif
+
return (0);
}
diff --git a/cpu/mcf523x/cpu_init.c b/cpu/mcf523x/cpu_init.c
index 55c9cd3..8ab5b8e 100644
--- a/cpu/mcf523x/cpu_init.c
+++ b/cpu/mcf523x/cpu_init.c
@@ -110,8 +110,8 @@ void cpu_init_f(void)
#endif
#ifdef CONFIG_FSL_I2C
- gpio->par_feci2c &= ~(GPIO_PAR_FECI2C_SCL_MASK | GPIO_PAR_FECI2C_SDA_MASK);
- gpio->par_feci2c |= (GPIO_PAR_FECI2C_SCL_I2CSCL | GPIO_PAR_FECI2C_SDA_I2CSDA);
+ CFG_I2C_PINMUX_REG &= CFG_I2C_PINMUX_CLR;
+ CFG_I2C_PINMUX_REG |= CFG_I2C_PINMUX_SET;
#endif
icache_enable();
diff --git a/cpu/mcf523x/speed.c b/cpu/mcf523x/speed.c
index 247d318..1bda2d4 100644
--- a/cpu/mcf523x/speed.c
+++ b/cpu/mcf523x/speed.c
@@ -45,5 +45,9 @@ int get_clocks(void)
gd->bus_clk = CFG_CLK;
gd->cpu_clk = (gd->bus_clk * 2);
+#ifdef CONFIG_FSL_I2C
+ gd->i2c1_clk = gd->bus_clk;
+#endif
+
return (0);
}
diff --git a/cpu/mcf52x2/cpu_init.c b/cpu/mcf52x2/cpu_init.c
index 3cacb55..68aefe9 100644
--- a/cpu/mcf52x2/cpu_init.c
+++ b/cpu/mcf52x2/cpu_init.c
@@ -80,6 +80,15 @@ void cpu_init_f(void)
mbar_writeShort(MCFSIM_CSCR0, CFG_CSCR0);
mbar_writeLong(MCFSIM_CSMR0, CFG_CSMR0);
+#ifdef CONFIG_FSL_I2C
+ CFG_I2C_PINMUX_REG = CFG_I2C_PINMUX_REG & CFG_I2C_PINMUX_CLR;
+ CFG_I2C_PINMUX_REG |= CFG_I2C_PINMUX_SET;
+#ifdef CFG_I2C2_OFFSET
+ CFG_I2C2_PINMUX_REG &= CFG_I2C2_PINMUX_CLR;
+ CFG_I2C2_PINMUX_REG |= CFG_I2C2_PINMUX_SET;
+#endif
+#endif
+
/* enable instruction cache now */
icache_enable();
}
@@ -322,7 +331,8 @@ void cpu_init_f(void)
#endif /* #ifndef CONFIG_MONITOR_IS_IN_RAM */
#ifdef CONFIG_FSL_I2C
- gpio_reg->par_feci2c = 0x000F;
+ CFG_I2C_PINMUX_REG &= CFG_I2C_PINMUX_CLR;
+ CFG_I2C_PINMUX_REG |= CFG_I2C_PINMUX_SET;
#endif
/* enable instruction cache now */
diff --git a/cpu/mcf52x2/speed.c b/cpu/mcf52x2/speed.c
index f6edd5b..4cb8f93 100644
--- a/cpu/mcf52x2/speed.c
+++ b/cpu/mcf52x2/speed.c
@@ -82,5 +82,13 @@ int get_clocks (void)
#else
gd->bus_clk = gd->cpu_clk;
#endif
+
+#ifdef CONFIG_FSL_I2C
+ gd->i2c1_clk = gd->bus_clk;
+#ifdef CFG_I2C2_OFFSET
+ gd->i2c2_clk = gd->bus_clk;
+#endif
+#endif
+
return (0);
}
diff --git a/cpu/mcf532x/speed.c b/cpu/mcf532x/speed.c
index 001b9f4..a11e425 100644
--- a/cpu/mcf532x/speed.c
+++ b/cpu/mcf532x/speed.c
@@ -212,5 +212,10 @@ int get_clocks(void)
{
gd->bus_clk = clock_pll(CFG_CLK / 1000, 0) * 1000;
gd->cpu_clk = (gd->bus_clk * 3);
+
+#ifdef CONFIG_FSL_I2C
+ gd->i2c1_clk = gd->bus_clk;
+#endif
+
return (0);
}
diff --git a/cpu/mcf5445x/speed.c b/cpu/mcf5445x/speed.c
index f677f3c..6711a1d 100644
--- a/cpu/mcf5445x/speed.c
+++ b/cpu/mcf5445x/speed.c
@@ -209,5 +209,9 @@ int get_clocks(void)
#endif
}
+#ifdef CONFIG_FSL_I2C
+ gd->i2c1_clk = gd->bus_clk;
+#endif
+
return (0);
}
diff --git a/cpu/mcf547x_8x/speed.c b/cpu/mcf547x_8x/speed.c
index 389e7c9..28fe657 100644
--- a/cpu/mcf547x_8x/speed.c
+++ b/cpu/mcf547x_8x/speed.c
@@ -39,5 +39,10 @@ int get_clocks(void)
gd->bus_clk = CFG_CLK;
gd->cpu_clk = (gd->bus_clk * 2);
+
+#ifdef CONFIG_FSL_I2C
+ gd->i2c1_clk = gd->bus_clk;
+#endif
+
return (0);
}
diff --git a/cpu/mpc512x/Makefile b/cpu/mpc512x/Makefile
index 8ba8ae8..e8f1060 100644
--- a/cpu/mpc512x/Makefile
+++ b/cpu/mpc512x/Makefile
@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
LIB = $(obj)lib$(CPU).a
START = start.o
-COBJS = traps.o cpu.o cpu_init.o speed.o interrupts.o serial.o fec.o i2c.o iopin.o
+COBJS = traps.o cpu.o cpu_init.o speed.o interrupts.o serial.o i2c.o iopin.o
SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
diff --git a/cpu/mpc512x/fec.c b/cpu/mpc512x/fec.c
deleted file mode 100644
index e9df7de..0000000
--- a/cpu/mpc512x/fec.c
+++ /dev/null
@@ -1,794 +0,0 @@
-/*
- * (C) Copyright 2003-2007
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * Derived from the MPC8xx FEC driver.
- * Adapted for MPC512x by Grzegorz Bernacki <gjb@semihalf.com>
- */
-
-#include <common.h>
-#include <mpc512x.h>
-#include <malloc.h>
-#include <net.h>
-#include <miiphy.h>
-#include "fec.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define DEBUG 0
-
-#if defined(CONFIG_CMD_NET) && defined(CONFIG_NET_MULTI) && \
- defined(CONFIG_MPC512x_FEC)
-
-#if !(defined(CONFIG_MII) || defined(CONFIG_CMD_MII))
-#error "CONFIG_MII has to be defined!"
-#endif
-
-#if (DEBUG & 0x40)
-static uint32 local_crc32(char *string, unsigned int crc_value, int len);
-#endif
-
-int fec512x_miiphy_read(char *devname, uint8 phyAddr, uint8 regAddr, uint16 * retVal);
-int fec512x_miiphy_write(char *devname, uint8 phyAddr, uint8 regAddr, uint16 data);
-int mpc512x_fec_init_phy(struct eth_device *dev, bd_t * bis);
-
-static uchar rx_buff[FEC_BUFFER_SIZE];
-static int rx_buff_idx = 0;
-
-/********************************************************************/
-#if (DEBUG & 0x2)
-static void mpc512x_fec_phydump (char *devname)
-{
- uint16 phyStatus, i;
- uint8 phyAddr = CONFIG_PHY_ADDR;
- uint8 reg_mask[] = {
- /* regs to print: 0...8, 21,27,31 */
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0, 0, 0, 0, 0, 0,
- 0, 0, 0, 0, 0, 1, 0, 0, 0, 0, 0, 1, 0, 0, 0, 1,
- };
-
- for (i = 0; i < 32; i++) {
- if (reg_mask[i]) {
- miiphy_read (devname, phyAddr, i, &phyStatus);
- printf ("Mii reg %d: 0x%04x\n", i, phyStatus);
- }
- }
-}
-#endif
-
-/********************************************************************/
-static int mpc512x_fec_bd_init (mpc512x_fec_priv *fec)
-{
- int ix;
-
- /*
- * Receive BDs init
- */
- for (ix = 0; ix < FEC_RBD_NUM; ix++) {
- fec->bdBase->rbd[ix].dataPointer = (uint32)&fec->bdBase->recv_frames[ix];
- fec->bdBase->rbd[ix].status = FEC_RBD_EMPTY;
- fec->bdBase->rbd[ix].dataLength = 0;
- }
-
- /*
- * have the last RBD to close the ring
- */
- fec->bdBase->rbd[ix - 1].status |= FEC_RBD_WRAP;
- fec->rbdIndex = 0;
-
- /*
- * Trasmit BDs init
- */
- for (ix = 0; ix < FEC_TBD_NUM; ix++) {
- fec->bdBase->tbd[ix].status = 0;
- }
-
- /*
- * Have the last TBD to close the ring
- */
- fec->bdBase->tbd[ix - 1].status |= FEC_TBD_WRAP;
-
- /*
- * Initialize some indices
- */
- fec->tbdIndex = 0;
- fec->usedTbdIndex = 0;
- fec->cleanTbdNum = FEC_TBD_NUM;
-
- return 0;
-}
-
-/********************************************************************/
-static void mpc512x_fec_rbd_clean (mpc512x_fec_priv *fec, volatile FEC_RBD * pRbd)
-{
- /*
- * Reset buffer descriptor as empty
- */
- if ((fec->rbdIndex) == (FEC_RBD_NUM - 1))
- pRbd->status = (FEC_RBD_WRAP | FEC_RBD_EMPTY);
- else
- pRbd->status = FEC_RBD_EMPTY;
-
- pRbd->dataLength = 0;
-
- /*
- * Increment BD count
- */
- fec->rbdIndex = (fec->rbdIndex + 1) % FEC_RBD_NUM;
-
- /*
- * Now, we have an empty RxBD, notify FEC
- */
- fec->eth->r_des_active = 0x01000000; /* Descriptor polling active */
-}
-
-/********************************************************************/
-static void mpc512x_fec_tbd_scrub (mpc512x_fec_priv *fec)
-{
- volatile FEC_TBD *pUsedTbd;
-
-#if (DEBUG & 0x1)
- printf ("tbd_scrub: fec->cleanTbdNum = %d, fec->usedTbdIndex = %d\n",
- fec->cleanTbdNum, fec->usedTbdIndex);
-#endif
-
- /*
- * process all the consumed TBDs
- */
- while (fec->cleanTbdNum < FEC_TBD_NUM) {
- pUsedTbd = &fec->bdBase->tbd[fec->usedTbdIndex];
- if (pUsedTbd->status & FEC_TBD_READY) {
-#if (DEBUG & 0x20)
- printf ("Cannot clean TBD %d, in use\n", fec->usedTbdIndex);
-#endif
- return;
- }
-
- /*
- * clean this buffer descriptor
- */
- if (fec->usedTbdIndex == (FEC_TBD_NUM - 1))
- pUsedTbd->status = FEC_TBD_WRAP;
- else
- pUsedTbd->status = 0;
-
- /*
- * update some indeces for a correct handling of the TBD ring
- */
- fec->cleanTbdNum++;
- fec->usedTbdIndex = (fec->usedTbdIndex + 1) % FEC_TBD_NUM;
- }
-}
-
-/********************************************************************/
-static void mpc512x_fec_set_hwaddr (mpc512x_fec_priv *fec, char *mac)
-{
- uint8 currByte; /* byte for which to compute the CRC */
- int byte; /* loop - counter */
- int bit; /* loop - counter */
- uint32 crc = 0xffffffff; /* initial value */
-
- /*
- * The algorithm used is the following:
- * we loop on each of the six bytes of the provided address,
- * and we compute the CRC by left-shifting the previous
- * value by one position, so that each bit in the current
- * byte of the address may contribute the calculation. If
- * the latter and the MSB in the CRC are different, then
- * the CRC value so computed is also ex-ored with the
- * "polynomium generator". The current byte of the address
- * is also shifted right by one bit at each iteration.
- * This is because the CRC generatore in hardware is implemented
- * as a shift-register with as many ex-ores as the radixes
- * in the polynomium. This suggests that we represent the
- * polynomiumm itself as a 32-bit constant.
- */
- for (byte = 0; byte < 6; byte++) {
- currByte = mac[byte];
- for (bit = 0; bit < 8; bit++) {
- if ((currByte & 0x01) ^ (crc & 0x01)) {
- crc >>= 1;
- crc = crc ^ 0xedb88320;
- } else {
- crc >>= 1;
- }
- currByte >>= 1;
- }
- }
-
- crc = crc >> 26;
-
- /*
- * Set individual hash table register
- */
- if (crc >= 32) {
- fec->eth->iaddr1 = (1 << (crc - 32));
- fec->eth->iaddr2 = 0;
- } else {
- fec->eth->iaddr1 = 0;
- fec->eth->iaddr2 = (1 << crc);
- }
-
- /*
- * Set physical address
- */
- fec->eth->paddr1 = (mac[0] << 24) + (mac[1] << 16) + (mac[2] << 8) + mac[3];
- fec->eth->paddr2 = (mac[4] << 24) + (mac[5] << 16) + 0x8808;
-}
-
-/********************************************************************/
-static int mpc512x_fec_init (struct eth_device *dev, bd_t * bis)
-{
- mpc512x_fec_priv *fec = (mpc512x_fec_priv *)dev->priv;
-
-#if (DEBUG & 0x1)
- printf ("mpc512x_fec_init... Begin\n");
-#endif
-
- /* Set interrupt mask register */
- fec->eth->imask = 0x00000000;
-
- /* Clear FEC-Lite interrupt event register(IEVENT) */
- fec->eth->ievent = 0xffffffff;
-
- /* Set transmit fifo watermark register(X_WMRK), default = 64 */
- fec->eth->x_wmrk = 0x0;
-
- /* Set Opcode/Pause Duration Register */
- fec->eth->op_pause = 0x00010020;
-
- /* Frame length=1522; MII mode */
- fec->eth->r_cntrl = (FEC_MAX_FRAME_LEN << 16) | 0x24;
-
- /* Half-duplex, heartbeat disabled */
- fec->eth->x_cntrl = 0x00000000;
-
- /* Enable MIB counters */
- fec->eth->mib_control = 0x0;
-
- /* Setup recv fifo start and buff size */
- fec->eth->r_fstart = 0x500;
- fec->eth->r_buff_size = FEC_BUFFER_SIZE;
-
- /* Setup BD base addresses */
- fec->eth->r_des_start = (uint32)fec->bdBase->rbd;
- fec->eth->x_des_start = (uint32)fec->bdBase->tbd;
-
- /* DMA Control */
- fec->eth->dma_control = 0xc0000000;
-
- /* Enable FEC */
- fec->eth->ecntrl |= 0x00000006;
-
- /* Initilize addresses and status words of BDs */
- mpc512x_fec_bd_init (fec);
-
- /* Descriptor polling active */
- fec->eth->r_des_active = 0x01000000;
-
-#if (DEBUG & 0x1)
- printf("mpc512x_fec_init... Done \n");
-#endif
- return 1;
-}
-
-/********************************************************************/
-int mpc512x_fec_init_phy (struct eth_device *dev, bd_t * bis)
-{
- mpc512x_fec_priv *fec = (mpc512x_fec_priv *)dev->priv;
- const uint8 phyAddr = CONFIG_PHY_ADDR; /* Only one PHY */
- int timeout = 1;
- uint16 phyStatus;
-
-#if (DEBUG & 0x1)
- printf ("mpc512x_fec_init_phy... Begin\n");
-#endif
-
- /*
- * Clear FEC-Lite interrupt event register(IEVENT)
- */
- fec->eth->ievent = 0xffffffff;
-
- /*
- * Set interrupt mask register
- */
- fec->eth->imask = 0x00000000;
-
- if (fec->xcv_type != SEVENWIRE) {
- /*
- * Set MII_SPEED = (1/(mii_speed * 2)) * System Clock
- * and do not drop the Preamble.
- */
- fec->eth->mii_speed = (((gd->ips_clk / 1000000) / 5) + 1) << 1;
-
- /*
- * Reset PHY, then delay 300ns
- */
- miiphy_write (dev->name, phyAddr, 0x0, 0x8000);
- udelay (1000);
-
- if (fec->xcv_type == MII10) {
- /*
- * Force 10Base-T, FDX operation
- */
-#if (DEBUG & 0x2)
- printf ("Forcing 10 Mbps ethernet link... ");
-#endif
- miiphy_read (dev->name, phyAddr, 0x1, &phyStatus);
-
- miiphy_write (dev->name, phyAddr, 0x0, 0x0180);
-
- timeout = 20;
- do { /* wait for link status to go down */
- udelay (10000);
- if ((timeout--) == 0) {
-#if (DEBUG & 0x2)
- printf ("hmmm, should not have waited...");
-#endif
- break;
- }
- miiphy_read (dev->name, phyAddr, 0x1, &phyStatus);
-#if (DEBUG & 0x2)
- printf ("=");
-#endif
- } while ((phyStatus & 0x0004)); /* !link up */
-
- timeout = 1000;
- do { /* wait for link status to come back up */
- udelay (10000);
- if ((timeout--) == 0) {
- printf ("failed. Link is down.\n");
- break;
- }
- miiphy_read (dev->name, phyAddr, 0x1, &phyStatus);
-#if (DEBUG & 0x2)
- printf ("+");
-#endif
- } while (!(phyStatus & 0x0004)); /* !link up */
-
-#if (DEBUG & 0x2)
- printf ("done.\n");
-#endif
- } else { /* MII100 */
- /*
- * Set the auto-negotiation advertisement register bits
- */
- miiphy_write (dev->name, phyAddr, 0x4, 0x01e1);
-
- /*
- * Set MDIO bit 0.12 = 1(&& bit 0.9=1?) to enable auto-negotiation
- */
- miiphy_write (dev->name, phyAddr, 0x0, 0x1200);
-
- /*
- * Wait for AN completion
- */
- timeout = 50000;
- do {
- udelay (1000);
-
- if ((timeout--) == 0) {
-#if (DEBUG & 0x2)
- printf ("PHY auto neg 0 failed...\n");
-#endif
- return -1;
- }
-
- if (miiphy_read (dev->name, phyAddr, 0x1, &phyStatus) != 0) {
-#if (DEBUG & 0x2)
- printf ("PHY auto neg 1 failed 0x%04x...\n", phyStatus);
-#endif
- return -1;
- }
- } while (!(phyStatus & 0x0004));
-
-#if (DEBUG & 0x2)
- printf ("PHY auto neg complete! \n");
-#endif
- }
- }
-
-#if (DEBUG & 0x2)
- if (fec->xcv_type != SEVENWIRE)
- mpc512x_fec_phydump (dev->name);
-#endif
-
-#if (DEBUG & 0x1)
- printf ("mpc512x_fec_init_phy... Done \n");
-#endif
- return 1;
-}
-
-/********************************************************************/
-static void mpc512x_fec_halt (struct eth_device *dev)
-{
- mpc512x_fec_priv *fec = (mpc512x_fec_priv *)dev->priv;
- int counter = 0xffff;
-
-#if (DEBUG & 0x2)
- if (fec->xcv_type != SEVENWIRE)
- mpc512x_fec_phydump (dev->name);
-#endif
-
- /*
- * mask FEC chip interrupts
- */
- fec->eth->imask = 0;
-
- /*
- * issue graceful stop command to the FEC transmitter if necessary
- */
- fec->eth->x_cntrl |= 0x00000001;
-
- /*
- * wait for graceful stop to register
- */
- while ((counter--) && (!(fec->eth->ievent & 0x10000000))) ;
-
- /*
- * Disable the Ethernet Controller
- */
- fec->eth->ecntrl &= 0xfffffffd;
-
- /*
- * Issue a reset command to the FEC chip
- */
- fec->eth->ecntrl |= 0x1;
-
- /*
- * wait at least 16 clock cycles
- */
- udelay (10);
-#if (DEBUG & 0x3)
- printf ("Ethernet task stopped\n");
-#endif
-}
-
-/********************************************************************/
-
-static int mpc512x_fec_send (struct eth_device *dev, volatile void *eth_data,
- int data_length)
-{
- /*
- * This routine transmits one frame. This routine only accepts
- * 6-byte Ethernet addresses.
- */
- mpc512x_fec_priv *fec = (mpc512x_fec_priv *)dev->priv;
- volatile FEC_TBD *pTbd;
-
-#if (DEBUG & 0x20)
- printf("tbd status: 0x%04x\n", fec->tbdBase[fec->tbdIndex].status);
-#endif
-
- /*
- * Clear Tx BD ring at first
- */
- mpc512x_fec_tbd_scrub (fec);
-
- /*
- * Check for valid length of data.
- */
- if ((data_length > 1500) || (data_length <= 0)) {
- return -1;
- }
-
- /*
- * Check the number of vacant TxBDs.
- */
- if (fec->cleanTbdNum < 1) {
-#if (DEBUG & 0x20)
- printf ("No available TxBDs ...\n");
-#endif
- return -1;
- }
-
- /*
- * Get the first TxBD to send the mac header
- */
- pTbd = &fec->bdBase->tbd[fec->tbdIndex];
- pTbd->dataLength = data_length;
- pTbd->dataPointer = (uint32)eth_data;
- pTbd->status |= FEC_TBD_LAST | FEC_TBD_TC | FEC_TBD_READY;
- fec->tbdIndex = (fec->tbdIndex + 1) % FEC_TBD_NUM;
-
- /* Activate transmit Buffer Descriptor polling */
- fec->eth->x_des_active = 0x01000000; /* Descriptor polling active */
-
-#if (DEBUG & 0x8)
- printf ( "+" );
-#endif
-
- fec->cleanTbdNum -= 1;
-
- /*
- * wait until frame is sent .
- */
- while (pTbd->status & FEC_TBD_READY) {
- udelay (10);
-#if (DEBUG & 0x8)
- printf ("TDB status = %04x\n", pTbd->status);
-#endif
- }
-
- return 0;
-}
-
-
-/********************************************************************/
-static int mpc512x_fec_recv (struct eth_device *dev)
-{
- /*
- * This command pulls one frame from the card
- */
- mpc512x_fec_priv *fec = (mpc512x_fec_priv *)dev->priv;
- volatile FEC_RBD *pRbd = &fec->bdBase->rbd[fec->rbdIndex];
- unsigned long ievent;
- int frame_length = 0;
-
-#if (DEBUG & 0x1)
- printf ("mpc512x_fec_recv %d Start...\n", fec->rbdIndex);
-#endif
-#if (DEBUG & 0x8)
- printf( "-" );
-#endif
-
- /*
- * Check if any critical events have happened
- */
- ievent = fec->eth->ievent;
- fec->eth->ievent = ievent;
- if (ievent & 0x20060000) {
- /* BABT, Rx/Tx FIFO errors */
- mpc512x_fec_halt (dev);
- mpc512x_fec_init (dev, NULL);
- return 0;
- }
- if (ievent & 0x80000000) {
- /* Heartbeat error */
- fec->eth->x_cntrl |= 0x00000001;
- }
- if (ievent & 0x10000000) {
- /* Graceful stop complete */
- if (fec->eth->x_cntrl & 0x00000001) {
- mpc512x_fec_halt (dev);
- fec->eth->x_cntrl &= ~0x00000001;
- mpc512x_fec_init (dev, NULL);
- }
- }
-
- if (!(pRbd->status & FEC_RBD_EMPTY)) {
- if (!(pRbd->status & FEC_RBD_ERR) &&
- ((pRbd->dataLength - 4) > 14)) {
-
- /*
- * Get buffer size
- */
- if (pRbd->status & FEC_RBD_LAST)
- frame_length = pRbd->dataLength - 4;
- else
- frame_length = pRbd->dataLength;
-#if (DEBUG & 0x20)
- {
- int i;
- printf ("recv data length 0x%08x data hdr: ",
- pRbd->dataLength);
- for (i = 0; i < 14; i++)
- printf ("%x ", *((uint8*)pRbd->dataPointer + i));
- printf("\n");
- }
-#endif
- /*
- * Fill the buffer and pass it to upper layers
- */
- memcpy (&rx_buff[rx_buff_idx], (void*)pRbd->dataPointer,
- frame_length - rx_buff_idx);
- rx_buff_idx = frame_length;
-
- if (pRbd->status & FEC_RBD_LAST) {
- NetReceive ((uchar*)rx_buff, frame_length);
- rx_buff_idx = 0;
- }
- }
-
- /*
- * Reset buffer descriptor as empty
- */
- mpc512x_fec_rbd_clean (fec, pRbd);
- }
-
- /* Try to fill Buffer Descriptors */
- fec->eth->r_des_active = 0x01000000; /* Descriptor polling active */
- return frame_length;
-}
-
-/********************************************************************/
-int mpc512x_fec_initialize (bd_t * bis)
-{
- mpc512x_fec_priv *fec;
- struct eth_device *dev;
- int i;
- char *tmp, *end, env_enetaddr[6];
- void * bd;
-
- fec = (mpc512x_fec_priv *) malloc (sizeof(*fec));
- dev = (struct eth_device *) malloc (sizeof(*dev));
- memset (dev, 0, sizeof *dev);
-
- fec->eth = (ethernet_regs *) MPC512X_FEC;
-
-# ifndef CONFIG_FEC_10MBIT
- fec->xcv_type = MII100;
-# else
- fec->xcv_type = MII10;
-# endif
- dev->priv = (void *)fec;
- dev->iobase = MPC512X_FEC;
- dev->init = mpc512x_fec_init;
- dev->halt = mpc512x_fec_halt;
- dev->send = mpc512x_fec_send;
- dev->recv = mpc512x_fec_recv;
-
- sprintf (dev->name, "FEC ETHERNET");
- eth_register (dev);
-
-#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
- miiphy_register (dev->name,
- fec512x_miiphy_read, fec512x_miiphy_write);
-#endif
-
- /* Clean up space FEC's MIB and FIFO RAM ...*/
- memset ((void *) MPC512X_FEC + 0x200, 0x00, 0x400);
-
- /*
- * Malloc space for BDs (must be quad word-aligned)
- * this pointer is lost, so cannot be freed
- */
- bd = malloc (sizeof(mpc512x_buff_descs) + 0x1f);
- fec->bdBase = (mpc512x_buff_descs*)((uint32)bd & 0xfffffff0);
- memset ((void *) bd, 0x00, sizeof(mpc512x_buff_descs) + 0x1f);
-
- /*
- * Set interrupt mask register
- */
- fec->eth->imask = 0x00000000;
-
- /*
- * Clear FEC-Lite interrupt event register(IEVENT)
- */
- fec->eth->ievent = 0xffffffff;
-
- /*
- * Try to set the mac address now. The fec mac address is
- * a garbage after reset. When not using fec for booting
- * the Linux fec driver will try to work with this garbage.
- */
- tmp = getenv ("ethaddr");
- if (tmp) {
- for (i=0; i<6; i++) {
- env_enetaddr[i] = tmp ? simple_strtoul (tmp, &end, 16) : 0;
- if (tmp)
- tmp = (*end) ? end+1 : end;
- }
- mpc512x_fec_set_hwaddr (fec, env_enetaddr);
- fec->eth->gaddr1 = 0x00000000;
- fec->eth->gaddr2 = 0x00000000;
- }
-
- mpc512x_fec_init_phy (dev, bis);
-
- return 1;
-}
-
-/* MII-interface related functions */
-/********************************************************************/
-int fec512x_miiphy_read (char *devname, uint8 phyAddr, uint8 regAddr, uint16 * retVal)
-{
- ethernet_regs *eth = (ethernet_regs *) MPC512X_FEC;
- uint32 reg; /* convenient holder for the PHY register */
- uint32 phy; /* convenient holder for the PHY */
- int timeout = 0xffff;
-
- /*
- * reading from any PHY's register is done by properly
- * programming the FEC's MII data register.
- */
- reg = regAddr << FEC_MII_DATA_RA_SHIFT;
- phy = phyAddr << FEC_MII_DATA_PA_SHIFT;
-
- eth->mii_data = (FEC_MII_DATA_ST | FEC_MII_DATA_OP_RD | FEC_MII_DATA_TA | phy | reg);
-
- /*
- * wait for the related interrupt
- */
- while ((timeout--) && (!(eth->ievent & 0x00800000))) ;
-
- if (timeout == 0) {
-#if (DEBUG & 0x2)
- printf ("Read MDIO failed...\n");
-#endif
- return -1;
- }
-
- /*
- * clear mii interrupt bit
- */
- eth->ievent = 0x00800000;
-
- /*
- * it's now safe to read the PHY's register
- */
- *retVal = (uint16) eth->mii_data;
-
- return 0;
-}
-
-/********************************************************************/
-int fec512x_miiphy_write (char *devname, uint8 phyAddr, uint8 regAddr, uint16 data)
-{
- ethernet_regs *eth = (ethernet_regs *) MPC512X_FEC;
- uint32 reg; /* convenient holder for the PHY register */
- uint32 phy; /* convenient holder for the PHY */
- int timeout = 0xffff;
-
- reg = regAddr << FEC_MII_DATA_RA_SHIFT;
- phy = phyAddr << FEC_MII_DATA_PA_SHIFT;
-
- eth->mii_data = (FEC_MII_DATA_ST | FEC_MII_DATA_OP_WR |
- FEC_MII_DATA_TA | phy | reg | data);
-
- /*
- * wait for the MII interrupt
- */
- while ((timeout--) && (!(eth->ievent & 0x00800000))) ;
-
- if (timeout == 0) {
-#if (DEBUG & 0x2)
- printf ("Write MDIO failed...\n");
-#endif
- return -1;
- }
-
- /*
- * clear MII interrupt bit
- */
- eth->ievent = 0x00800000;
-
- return 0;
-}
-
-#if (DEBUG & 0x40)
-static uint32 local_crc32 (char *string, unsigned int crc_value, int len)
-{
- int i;
- char c;
- unsigned int crc, count;
-
- /*
- * crc32 algorithm
- */
- /*
- * crc = 0xffffffff; * The initialized value should be 0xffffffff
- */
- crc = crc_value;
-
- for (i = len; --i >= 0;) {
- c = *string++;
- for (count = 0; count < 8; count++) {
- if ((c & 0x01) ^ (crc & 0x01)) {
- crc >>= 1;
- crc = crc ^ 0xedb88320;
- } else {
- crc >>= 1;
- }
- c >>= 1;
- }
- }
-
- /*
- * In big endian system, do byte swaping for crc value
- */
- /**/ return crc;
-}
-#endif /* DEBUG */
-
-#endif /* CONFIG_MPC512x_FEC */
diff --git a/cpu/mpc512x/fec.h b/cpu/mpc512x/fec.h
deleted file mode 100644
index 9c38502..0000000
--- a/cpu/mpc512x/fec.h
+++ /dev/null
@@ -1,227 +0,0 @@
-/*
- * (C) Copyright 2003 - 2007
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * Derived from the MPC8xx driver's header file.
- */
-
-#ifndef __MPC512X_FEC_H
-#define __MPC512X_FEC_H
-
-#include <common.h>
-#include <mpc512x.h>
-
-typedef unsigned long uint32;
-typedef unsigned short uint16;
-typedef unsigned char uint8;
-
-typedef struct ethernet_register_set {
-
-/* [10:2]addr = 00 */
-
-/* Control and status Registers (offset 000-1FF) */
-
- volatile uint32 fec_id; /* MBAR_ETH + 0x000 */
- volatile uint32 ievent; /* MBAR_ETH + 0x004 */
- volatile uint32 imask; /* MBAR_ETH + 0x008 */
-
- volatile uint32 RES0[1]; /* MBAR_ETH + 0x00C */
- volatile uint32 r_des_active; /* MBAR_ETH + 0x010 */
- volatile uint32 x_des_active; /* MBAR_ETH + 0x014 */
-
- volatile uint32 RES1[3]; /* MBAR_ETH + 0x018-020 */
- volatile uint32 ecntrl; /* MBAR_ETH + 0x024 */
-
- volatile uint32 RES2[6]; /* MBAR_ETH + 0x028-03C */
- volatile uint32 mii_data; /* MBAR_ETH + 0x040 */
- volatile uint32 mii_speed; /* MBAR_ETH + 0x044 */
-
- volatile uint32 RES3[7]; /* MBAR_ETH + 0x048-060 */
- volatile uint32 mib_control; /* MBAR_ETH + 0x064 */
-
- volatile uint32 RES4[7]; /* MBAR_ETH + 0x068-80 */
- volatile uint32 r_cntrl; /* MBAR_ETH + 0x084 */
- volatile uint32 r_hash; /* MBAR_ETH + 0x088 */
-
- volatile uint32 RES5[14]; /* MBAR_ETH + 0x08c-0C0 */
- volatile uint32 x_cntrl; /* MBAR_ETH + 0x0C4 */
-
- volatile uint32 RES6[7]; /* MBAR_ETH + 0x0C8-0E0 */
- volatile uint32 paddr1; /* MBAR_ETH + 0x0E4 */
- volatile uint32 paddr2; /* MBAR_ETH + 0x0E8 */
- volatile uint32 op_pause; /* MBAR_ETH + 0x0EC */
-
- volatile uint32 RES7[10]; /* MBAR_ETH + 0x0F0-114 */
- volatile uint32 iaddr1; /* MBAR_ETH + 0x118 */
- volatile uint32 iaddr2; /* MBAR_ETH + 0x11C */
- volatile uint32 gaddr1; /* MBAR_ETH + 0x120 */
- volatile uint32 gaddr2; /* MBAR_ETH + 0x124 */
-
- volatile uint32 RES8[6]; /* MBAR_ETH + 0x128-13C */
- volatile uint32 fifo_id; /* MBAR_ETH + 0x140 */
- volatile uint32 x_wmrk; /* MBAR_ETH + 0x144 */
- volatile uint32 RES9[1]; /* MBAR_ETH + 0x148 */
- volatile uint32 r_bound; /* MBAR_ETH + 0x14C */
- volatile uint32 r_fstart; /* MBAR_ETH + 0x150 */
-
- volatile uint32 RES10[11]; /* MBAR_ETH + 0x154-17C */
- volatile uint32 r_des_start; /* MBAR_ETH + 0x180 */
- volatile uint32 x_des_start; /* MBAR_ETH + 0x184 */
- volatile uint32 r_buff_size; /* MBAR_ETH + 0x188 */
- volatile uint32 RES11[26]; /* MBAR_ETH + 0x18C-1F0 */
- volatile uint32 dma_control; /* MBAR_ETH + 0x1F4 */
- volatile uint32 RES12[2]; /* MBAR_ETH + 0x1F8-1FC */
-
-/* MIB COUNTERS (Offset 200-2FF) */
-
- volatile uint32 rmon_t_drop; /* MBAR_ETH + 0x200 */
- volatile uint32 rmon_t_packets; /* MBAR_ETH + 0x204 */
- volatile uint32 rmon_t_bc_pkt; /* MBAR_ETH + 0x208 */
- volatile uint32 rmon_t_mc_pkt; /* MBAR_ETH + 0x20C */
- volatile uint32 rmon_t_crc_align; /* MBAR_ETH + 0x210 */
- volatile uint32 rmon_t_undersize; /* MBAR_ETH + 0x214 */
- volatile uint32 rmon_t_oversize; /* MBAR_ETH + 0x218 */
- volatile uint32 rmon_t_frag; /* MBAR_ETH + 0x21C */
- volatile uint32 rmon_t_jab; /* MBAR_ETH + 0x220 */
- volatile uint32 rmon_t_col; /* MBAR_ETH + 0x224 */
- volatile uint32 rmon_t_p64; /* MBAR_ETH + 0x228 */
- volatile uint32 rmon_t_p65to127; /* MBAR_ETH + 0x22C */
- volatile uint32 rmon_t_p128to255; /* MBAR_ETH + 0x230 */
- volatile uint32 rmon_t_p256to511; /* MBAR_ETH + 0x234 */
- volatile uint32 rmon_t_p512to1023; /* MBAR_ETH + 0x238 */
- volatile uint32 rmon_t_p1024to2047; /* MBAR_ETH + 0x23C */
- volatile uint32 rmon_t_p_gte2048; /* MBAR_ETH + 0x240 */
- volatile uint32 rmon_t_octets; /* MBAR_ETH + 0x244 */
- volatile uint32 ieee_t_drop; /* MBAR_ETH + 0x248 */
- volatile uint32 ieee_t_frame_ok; /* MBAR_ETH + 0x24C */
- volatile uint32 ieee_t_1col; /* MBAR_ETH + 0x250 */
- volatile uint32 ieee_t_mcol; /* MBAR_ETH + 0x254 */
- volatile uint32 ieee_t_def; /* MBAR_ETH + 0x258 */
- volatile uint32 ieee_t_lcol; /* MBAR_ETH + 0x25C */
- volatile uint32 ieee_t_excol; /* MBAR_ETH + 0x260 */
- volatile uint32 ieee_t_macerr; /* MBAR_ETH + 0x264 */
- volatile uint32 ieee_t_cserr; /* MBAR_ETH + 0x268 */
- volatile uint32 ieee_t_sqe; /* MBAR_ETH + 0x26C */
- volatile uint32 t_fdxfc; /* MBAR_ETH + 0x270 */
- volatile uint32 ieee_t_octets_ok; /* MBAR_ETH + 0x274 */
-
- volatile uint32 RES13[2]; /* MBAR_ETH + 0x278-27C */
- volatile uint32 rmon_r_drop; /* MBAR_ETH + 0x280 */
- volatile uint32 rmon_r_packets; /* MBAR_ETH + 0x284 */
- volatile uint32 rmon_r_bc_pkt; /* MBAR_ETH + 0x288 */
- volatile uint32 rmon_r_mc_pkt; /* MBAR_ETH + 0x28C */
- volatile uint32 rmon_r_crc_align; /* MBAR_ETH + 0x290 */
- volatile uint32 rmon_r_undersize; /* MBAR_ETH + 0x294 */
- volatile uint32 rmon_r_oversize; /* MBAR_ETH + 0x298 */
- volatile uint32 rmon_r_frag; /* MBAR_ETH + 0x29C */
- volatile uint32 rmon_r_jab; /* MBAR_ETH + 0x2A0 */
-
- volatile uint32 rmon_r_resvd_0; /* MBAR_ETH + 0x2A4 */
-
- volatile uint32 rmon_r_p64; /* MBAR_ETH + 0x2A8 */
- volatile uint32 rmon_r_p65to127; /* MBAR_ETH + 0x2AC */
- volatile uint32 rmon_r_p128to255; /* MBAR_ETH + 0x2B0 */
- volatile uint32 rmon_r_p256to511; /* MBAR_ETH + 0x2B4 */
- volatile uint32 rmon_r_p512to1023; /* MBAR_ETH + 0x2B8 */
- volatile uint32 rmon_r_p1024to2047; /* MBAR_ETH + 0x2BC */
- volatile uint32 rmon_r_p_gte2048; /* MBAR_ETH + 0x2C0 */
- volatile uint32 rmon_r_octets; /* MBAR_ETH + 0x2C4 */
- volatile uint32 ieee_r_drop; /* MBAR_ETH + 0x2C8 */
- volatile uint32 ieee_r_frame_ok; /* MBAR_ETH + 0x2CC */
- volatile uint32 ieee_r_crc; /* MBAR_ETH + 0x2D0 */
- volatile uint32 ieee_r_align; /* MBAR_ETH + 0x2D4 */
- volatile uint32 r_macerr; /* MBAR_ETH + 0x2D8 */
- volatile uint32 r_fdxfc; /* MBAR_ETH + 0x2DC */
- volatile uint32 ieee_r_octets_ok; /* MBAR_ETH + 0x2E0 */
-
- volatile uint32 RES14[6]; /* MBAR_ETH + 0x2E4-2FC */
-
- volatile uint32 RES15[64]; /* MBAR_ETH + 0x300-3FF */
-} ethernet_regs;
-
-/* Receive & Transmit Buffer Descriptor definitions */
-typedef struct BufferDescriptor {
- uint16 status;
- uint16 dataLength;
- uint32 dataPointer;
-} FEC_RBD;
-
-typedef struct {
- uint16 status;
- uint16 dataLength;
- uint32 dataPointer;
-} FEC_TBD;
-
-/* private structure */
-typedef enum {
- SEVENWIRE, /* 7-wire */
- MII10, /* MII 10Mbps */
- MII100 /* MII 100Mbps */
-} xceiver_type;
-
-/* BD Numer definitions */
-#define FEC_TBD_NUM 48 /* The user can adjust this value */
-#define FEC_RBD_NUM 32 /* The user can adjust this value */
-
-/* packet size limit */
-#define FEC_MAX_FRAME_LEN 1522 /* recommended default value */
-
-/* Buffer size must be evenly divisible by 16 */
-#define FEC_BUFFER_SIZE ((FEC_MAX_FRAME_LEN + 0x10) & (~0xf))
-
-typedef struct {
- uint8 frame[FEC_BUFFER_SIZE];
-} mpc512x_frame;
-
-typedef struct {
- FEC_RBD rbd[FEC_RBD_NUM]; /* RBD ring */
- FEC_TBD tbd[FEC_TBD_NUM]; /* TBD ring */
- mpc512x_frame recv_frames[FEC_RBD_NUM]; /* receive buff */
-} mpc512x_buff_descs;
-
-typedef struct {
- ethernet_regs *eth;
- xceiver_type xcv_type; /* transceiver type */
- mpc512x_buff_descs *bdBase; /* BD rings and recv buffer */
- uint16 rbdIndex; /* next receive BD to read */
- uint16 tbdIndex; /* next transmit BD to send */
- uint16 usedTbdIndex; /* next transmit BD to clean */
- uint16 cleanTbdNum; /* the number of available transmit BDs */
-} mpc512x_fec_priv;
-
-/* RBD bits definitions */
-#define FEC_RBD_EMPTY 0x8000 /* Buffer is empty */
-#define FEC_RBD_WRAP 0x2000 /* Last BD in ring */
-#define FEC_RBD_LAST 0x0800 /* Buffer is last in frame(useless) */
-#define FEC_RBD_MISS 0x0100 /* Miss bit for prom mode */
-#define FEC_RBD_BC 0x0080 /* The received frame is broadcast frame */
-#define FEC_RBD_MC 0x0040 /* The received frame is multicast frame */
-#define FEC_RBD_LG 0x0020 /* Frame length violation */
-#define FEC_RBD_NO 0x0010 /* Nonoctet align frame */
-#define FEC_RBD_SH 0x0008 /* Short frame */
-#define FEC_RBD_CR 0x0004 /* CRC error */
-#define FEC_RBD_OV 0x0002 /* Receive FIFO overrun */
-#define FEC_RBD_TR 0x0001 /* Frame is truncated */
-#define FEC_RBD_ERR (FEC_RBD_LG | FEC_RBD_NO | FEC_RBD_CR | \
- FEC_RBD_OV | FEC_RBD_TR)
-
-/* TBD bits definitions */
-#define FEC_TBD_READY 0x8000 /* Buffer is ready */
-#define FEC_TBD_WRAP 0x2000 /* Last BD in ring */
-#define FEC_TBD_LAST 0x0800 /* Buffer is last in frame */
-#define FEC_TBD_TC 0x0400 /* Transmit the CRC */
-#define FEC_TBD_ABC 0x0200 /* Append bad CRC */
-
-/* MII-related definitios */
-#define FEC_MII_DATA_ST 0x40000000 /* Start of frame delimiter */
-#define FEC_MII_DATA_OP_RD 0x20000000 /* Perform a read operation */
-#define FEC_MII_DATA_OP_WR 0x10000000 /* Perform a write operation */
-#define FEC_MII_DATA_PA_MSK 0x0f800000 /* PHY Address field mask */
-#define FEC_MII_DATA_RA_MSK 0x007c0000 /* PHY Register field mask */
-#define FEC_MII_DATA_TA 0x00020000 /* Turnaround */
-#define FEC_MII_DATA_DATAMSK 0x0000ffff /* PHY data field */
-
-#define FEC_MII_DATA_RA_SHIFT 18 /* MII Register address bits */
-#define FEC_MII_DATA_PA_SHIFT 23 /* MII PHY address bits */
-
-#endif /* __MPC512X_FEC_H */
diff --git a/cpu/mpc5xxx/Makefile b/cpu/mpc5xxx/Makefile
index 312b0bf..06fdbcf 100644
--- a/cpu/mpc5xxx/Makefile
+++ b/cpu/mpc5xxx/Makefile
@@ -27,7 +27,7 @@ LIB = $(obj)lib$(CPU).a
START = start.o
SOBJS = io.o firmware_sc_task_bestcomm.impl.o firmware_sc_task.impl.o
-COBJS = i2c.o traps.o cpu.o cpu_init.o fec.o ide.o interrupts.o \
+COBJS = i2c.o traps.o cpu.o cpu_init.o ide.o interrupts.o \
loadtask.o pci_mpc5200.o serial.o speed.o usb_ohci.o usb.o
SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
diff --git a/cpu/mpc5xxx/fec.c b/cpu/mpc5xxx/fec.c
deleted file mode 100644
index bf804ee..0000000
--- a/cpu/mpc5xxx/fec.c
+++ /dev/null
@@ -1,1067 +0,0 @@
-/*
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * This file is based on mpc4200fec.c,
- * (C) Copyright Motorola, Inc., 2000
- */
-
-#include <common.h>
-#include <mpc5xxx.h>
-#include <malloc.h>
-#include <net.h>
-#include <miiphy.h>
-#include "sdma.h"
-#include "fec.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* #define DEBUG 0x28 */
-
-#if defined(CONFIG_CMD_NET) && defined(CONFIG_NET_MULTI) && \
- defined(CONFIG_MPC5xxx_FEC)
-
-#if !(defined(CONFIG_MII) || defined(CONFIG_CMD_MII))
-#error "CONFIG_MII has to be defined!"
-#endif
-
-#if (DEBUG & 0x60)
-static void tfifo_print(char *devname, mpc5xxx_fec_priv *fec);
-static void rfifo_print(char *devname, mpc5xxx_fec_priv *fec);
-#endif /* DEBUG */
-
-#if (DEBUG & 0x40)
-static uint32 local_crc32(char *string, unsigned int crc_value, int len);
-#endif
-
-typedef struct {
- uint8 data[1500]; /* actual data */
- int length; /* actual length */
- int used; /* buffer in use or not */
- uint8 head[16]; /* MAC header(6 + 6 + 2) + 2(aligned) */
-} NBUF;
-
-int fec5xxx_miiphy_read(char *devname, uint8 phyAddr, uint8 regAddr, uint16 * retVal);
-int fec5xxx_miiphy_write(char *devname, uint8 phyAddr, uint8 regAddr, uint16 data);
-
-/********************************************************************/
-#if (DEBUG & 0x2)
-static void mpc5xxx_fec_phydump (char *devname)
-{
- uint16 phyStatus, i;
- uint8 phyAddr = CONFIG_PHY_ADDR;
- uint8 reg_mask[] = {
-#if CONFIG_PHY_TYPE == 0x79c874 /* AMD Am79C874 */
- /* regs to print: 0...7, 16...19, 21, 23, 24 */
- 1, 1, 1, 1, 1, 1, 1, 1, 0, 0, 0, 0, 0, 0, 0, 0,
- 1, 1, 1, 1, 0, 1, 0, 1, 1, 0, 0, 0, 0, 0, 0, 0,
-#else
- /* regs to print: 0...8, 16...20 */
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0, 0, 0, 0, 0, 0,
- 1, 1, 1, 1, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
-#endif
- };
-
- for (i = 0; i < 32; i++) {
- if (reg_mask[i]) {
- miiphy_read(devname, phyAddr, i, &phyStatus);
- printf("Mii reg %d: 0x%04x\n", i, phyStatus);
- }
- }
-}
-#endif
-
-/********************************************************************/
-static int mpc5xxx_fec_rbd_init(mpc5xxx_fec_priv *fec)
-{
- int ix;
- char *data;
- static int once = 0;
-
- for (ix = 0; ix < FEC_RBD_NUM; ix++) {
- if (!once) {
- data = (char *)malloc(FEC_MAX_PKT_SIZE);
- if (data == NULL) {
- printf ("RBD INIT FAILED\n");
- return -1;
- }
- fec->rbdBase[ix].dataPointer = (uint32)data;
- }
- fec->rbdBase[ix].status = FEC_RBD_EMPTY;
- fec->rbdBase[ix].dataLength = 0;
- }
- once ++;
-
- /*
- * have the last RBD to close the ring
- */
- fec->rbdBase[ix - 1].status |= FEC_RBD_WRAP;
- fec->rbdIndex = 0;
-
- return 0;
-}
-
-/********************************************************************/
-static void mpc5xxx_fec_tbd_init(mpc5xxx_fec_priv *fec)
-{
- int ix;
-
- for (ix = 0; ix < FEC_TBD_NUM; ix++) {
- fec->tbdBase[ix].status = 0;
- }
-
- /*
- * Have the last TBD to close the ring
- */
- fec->tbdBase[ix - 1].status |= FEC_TBD_WRAP;
-
- /*
- * Initialize some indices
- */
- fec->tbdIndex = 0;
- fec->usedTbdIndex = 0;
- fec->cleanTbdNum = FEC_TBD_NUM;
-}
-
-/********************************************************************/
-static void mpc5xxx_fec_rbd_clean(mpc5xxx_fec_priv *fec, volatile FEC_RBD * pRbd)
-{
- /*
- * Reset buffer descriptor as empty
- */
- if ((fec->rbdIndex) == (FEC_RBD_NUM - 1))
- pRbd->status = (FEC_RBD_WRAP | FEC_RBD_EMPTY);
- else
- pRbd->status = FEC_RBD_EMPTY;
-
- pRbd->dataLength = 0;
-
- /*
- * Now, we have an empty RxBD, restart the SmartDMA receive task
- */
- SDMA_TASK_ENABLE(FEC_RECV_TASK_NO);
-
- /*
- * Increment BD count
- */
- fec->rbdIndex = (fec->rbdIndex + 1) % FEC_RBD_NUM;
-}
-
-/********************************************************************/
-static void mpc5xxx_fec_tbd_scrub(mpc5xxx_fec_priv *fec)
-{
- volatile FEC_TBD *pUsedTbd;
-
-#if (DEBUG & 0x1)
- printf ("tbd_scrub: fec->cleanTbdNum = %d, fec->usedTbdIndex = %d\n",
- fec->cleanTbdNum, fec->usedTbdIndex);
-#endif
-
- /*
- * process all the consumed TBDs
- */
- while (fec->cleanTbdNum < FEC_TBD_NUM) {
- pUsedTbd = &fec->tbdBase[fec->usedTbdIndex];
- if (pUsedTbd->status & FEC_TBD_READY) {
-#if (DEBUG & 0x20)
- printf("Cannot clean TBD %d, in use\n", fec->cleanTbdNum);
-#endif
- return;
- }
-
- /*
- * clean this buffer descriptor
- */
- if (fec->usedTbdIndex == (FEC_TBD_NUM - 1))
- pUsedTbd->status = FEC_TBD_WRAP;
- else
- pUsedTbd->status = 0;
-
- /*
- * update some indeces for a correct handling of the TBD ring
- */
- fec->cleanTbdNum++;
- fec->usedTbdIndex = (fec->usedTbdIndex + 1) % FEC_TBD_NUM;
- }
-}
-
-/********************************************************************/
-static void mpc5xxx_fec_set_hwaddr(mpc5xxx_fec_priv *fec, char *mac)
-{
- uint8 currByte; /* byte for which to compute the CRC */
- int byte; /* loop - counter */
- int bit; /* loop - counter */
- uint32 crc = 0xffffffff; /* initial value */
-
- /*
- * The algorithm used is the following:
- * we loop on each of the six bytes of the provided address,
- * and we compute the CRC by left-shifting the previous
- * value by one position, so that each bit in the current
- * byte of the address may contribute the calculation. If
- * the latter and the MSB in the CRC are different, then
- * the CRC value so computed is also ex-ored with the
- * "polynomium generator". The current byte of the address
- * is also shifted right by one bit at each iteration.
- * This is because the CRC generatore in hardware is implemented
- * as a shift-register with as many ex-ores as the radixes
- * in the polynomium. This suggests that we represent the
- * polynomiumm itself as a 32-bit constant.
- */
- for (byte = 0; byte < 6; byte++) {
- currByte = mac[byte];
- for (bit = 0; bit < 8; bit++) {
- if ((currByte & 0x01) ^ (crc & 0x01)) {
- crc >>= 1;
- crc = crc ^ 0xedb88320;
- } else {
- crc >>= 1;
- }
- currByte >>= 1;
- }
- }
-
- crc = crc >> 26;
-
- /*
- * Set individual hash table register
- */
- if (crc >= 32) {
- fec->eth->iaddr1 = (1 << (crc - 32));
- fec->eth->iaddr2 = 0;
- } else {
- fec->eth->iaddr1 = 0;
- fec->eth->iaddr2 = (1 << crc);
- }
-
- /*
- * Set physical address
- */
- fec->eth->paddr1 = (mac[0] << 24) + (mac[1] << 16) + (mac[2] << 8) + mac[3];
- fec->eth->paddr2 = (mac[4] << 24) + (mac[5] << 16) + 0x8808;
-}
-
-/********************************************************************/
-static int mpc5xxx_fec_init(struct eth_device *dev, bd_t * bis)
-{
- mpc5xxx_fec_priv *fec = (mpc5xxx_fec_priv *)dev->priv;
- struct mpc5xxx_sdma *sdma = (struct mpc5xxx_sdma *)MPC5XXX_SDMA;
-
-#if (DEBUG & 0x1)
- printf ("mpc5xxx_fec_init... Begin\n");
-#endif
-
- /*
- * Initialize RxBD/TxBD rings
- */
- mpc5xxx_fec_rbd_init(fec);
- mpc5xxx_fec_tbd_init(fec);
-
- /*
- * Clear FEC-Lite interrupt event register(IEVENT)
- */
- fec->eth->ievent = 0xffffffff;
-
- /*
- * Set interrupt mask register
- */
- fec->eth->imask = 0x00000000;
-
- /*
- * Set FEC-Lite receive control register(R_CNTRL):
- */
- if (fec->xcv_type == SEVENWIRE) {
- /*
- * Frame length=1518; 7-wire mode
- */
- fec->eth->r_cntrl = 0x05ee0020; /*0x05ee0000;FIXME */
- } else {
- /*
- * Frame length=1518; MII mode;
- */
- fec->eth->r_cntrl = 0x05ee0024; /*0x05ee0004;FIXME */
- }
-
- fec->eth->x_cntrl = 0x00000000; /* half-duplex, heartbeat disabled */
- if (fec->xcv_type != SEVENWIRE) {
- /*
- * Set MII_SPEED = (1/(mii_speed * 2)) * System Clock
- * and do not drop the Preamble.
- */
- fec->eth->mii_speed = (((gd->ipb_clk >> 20) / 5) << 1); /* No MII for 7-wire mode */
- }
-
- /*
- * Set Opcode/Pause Duration Register
- */
- fec->eth->op_pause = 0x00010020; /*FIXME 0xffff0020; */
-
- /*
- * Set Rx FIFO alarm and granularity value
- */
- fec->eth->rfifo_cntrl = 0x0c000000
- | (fec->eth->rfifo_cntrl & ~0x0f000000);
- fec->eth->rfifo_alarm = 0x0000030c;
-#if (DEBUG & 0x22)
- if (fec->eth->rfifo_status & 0x00700000 ) {
- printf("mpc5xxx_fec_init() RFIFO error\n");
- }
-#endif
-
- /*
- * Set Tx FIFO granularity value
- */
- fec->eth->tfifo_cntrl = 0x0c000000
- | (fec->eth->tfifo_cntrl & ~0x0f000000);
-#if (DEBUG & 0x2)
- printf("tfifo_status: 0x%08x\n", fec->eth->tfifo_status);
- printf("tfifo_alarm: 0x%08x\n", fec->eth->tfifo_alarm);
-#endif
-
- /*
- * Set transmit fifo watermark register(X_WMRK), default = 64
- */
- fec->eth->tfifo_alarm = 0x00000080;
- fec->eth->x_wmrk = 0x2;
-
- /*
- * Set individual address filter for unicast address
- * and set physical address registers.
- */
- mpc5xxx_fec_set_hwaddr(fec, (char *)dev->enetaddr);
-
- /*
- * Set multicast address filter
- */
- fec->eth->gaddr1 = 0x00000000;
- fec->eth->gaddr2 = 0x00000000;
-
- /*
- * Turn ON cheater FSM: ????
- */
- fec->eth->xmit_fsm = 0x03000000;
-
-#if defined(CONFIG_MPC5200)
- /*
- * Turn off COMM bus prefetch in the MGT5200 BestComm. It doesn't
- * work w/ the current receive task.
- */
- sdma->PtdCntrl |= 0x00000001;
-#endif
-
- /*
- * Set priority of different initiators
- */
- sdma->IPR0 = 7; /* always */
- sdma->IPR3 = 6; /* Eth RX */
- sdma->IPR4 = 5; /* Eth Tx */
-
- /*
- * Clear SmartDMA task interrupt pending bits
- */
- SDMA_CLEAR_IEVENT(FEC_RECV_TASK_NO);
-
- /*
- * Initialize SmartDMA parameters stored in SRAM
- */
- *(volatile int *)FEC_TBD_BASE = (int)fec->tbdBase;
- *(volatile int *)FEC_RBD_BASE = (int)fec->rbdBase;
- *(volatile int *)FEC_TBD_NEXT = (int)fec->tbdBase;
- *(volatile int *)FEC_RBD_NEXT = (int)fec->rbdBase;
-
- /*
- * Enable FEC-Lite controller
- */
- fec->eth->ecntrl |= 0x00000006;
-
-#if (DEBUG & 0x2)
- if (fec->xcv_type != SEVENWIRE)
- mpc5xxx_fec_phydump (dev->name);
-#endif
-
- /*
- * Enable SmartDMA receive task
- */
- SDMA_TASK_ENABLE(FEC_RECV_TASK_NO);
-
-#if (DEBUG & 0x1)
- printf("mpc5xxx_fec_init... Done \n");
-#endif
-
- return 1;
-}
-
-/********************************************************************/
-static int mpc5xxx_fec_init_phy(struct eth_device *dev, bd_t * bis)
-{
- mpc5xxx_fec_priv *fec = (mpc5xxx_fec_priv *)dev->priv;
- const uint8 phyAddr = CONFIG_PHY_ADDR; /* Only one PHY */
-
-#if (DEBUG & 0x1)
- printf ("mpc5xxx_fec_init_phy... Begin\n");
-#endif
-
- /*
- * Initialize GPIO pins
- */
- if (fec->xcv_type == SEVENWIRE) {
- /* 10MBit with 7-wire operation */
-#if defined(CONFIG_TOTAL5200)
- /* 7-wire and USB2 on Ethernet */
- *(vu_long *)MPC5XXX_GPS_PORT_CONFIG |= 0x00030000;
-#else /* !CONFIG_TOTAL5200 */
- /* 7-wire only */
- *(vu_long *)MPC5XXX_GPS_PORT_CONFIG |= 0x00020000;
-#endif /* CONFIG_TOTAL5200 */
- } else {
- /* 100MBit with MD operation */
- *(vu_long *)MPC5XXX_GPS_PORT_CONFIG |= 0x00050000;
- }
-
- /*
- * Clear FEC-Lite interrupt event register(IEVENT)
- */
- fec->eth->ievent = 0xffffffff;
-
- /*
- * Set interrupt mask register
- */
- fec->eth->imask = 0x00000000;
-
-/*
- * In original Promess-provided code PHY initialization is disabled with the
- * following comment: "Phy initialization is DISABLED for now. There was a
- * problem with running 100 Mbps on PRO board". Thus we temporarily disable
- * PHY initialization for the Motion-PRO board, until a proper fix is found.
- */
-
- if (fec->xcv_type != SEVENWIRE) {
- /*
- * Set MII_SPEED = (1/(mii_speed * 2)) * System Clock
- * and do not drop the Preamble.
- */
- fec->eth->mii_speed = (((gd->ipb_clk >> 20) / 5) << 1); /* No MII for 7-wire mode */
- }
-
- if (fec->xcv_type != SEVENWIRE) {
- /*
- * Initialize PHY(LXT971A):
- *
- * Generally, on power up, the LXT971A reads its configuration
- * pins to check for forced operation, If not cofigured for
- * forced operation, it uses auto-negotiation/parallel detection
- * to automatically determine line operating conditions.
- * If the PHY device on the other side of the link supports
- * auto-negotiation, the LXT971A auto-negotiates with it
- * using Fast Link Pulse(FLP) Bursts. If the PHY partner does not
- * support auto-negotiation, the LXT971A automatically detects
- * the presence of either link pulses(10Mbps PHY) or Idle
- * symbols(100Mbps) and sets its operating conditions accordingly.
- *
- * When auto-negotiation is controlled by software, the following
- * steps are recommended.
- *
- * Note:
- * The physical address is dependent on hardware configuration.
- *
- */
- int timeout = 1;
- uint16 phyStatus;
-
- /*
- * Reset PHY, then delay 300ns
- */
- miiphy_write(dev->name, phyAddr, 0x0, 0x8000);
- udelay(1000);
-
-#if defined(CONFIG_UC101) || defined(CONFIG_MUCMC52)
- /* Set the LED configuration Register for the UC101
- and MUCMC52 Board */
- miiphy_write(dev->name, phyAddr, 0x14, 0x4122);
-#endif
- if (fec->xcv_type == MII10) {
- /*
- * Force 10Base-T, FDX operation
- */
-#if (DEBUG & 0x2)
- printf("Forcing 10 Mbps ethernet link... ");
-#endif
- miiphy_read(dev->name, phyAddr, 0x1, &phyStatus);
- /*
- miiphy_write(dev->name, fec, phyAddr, 0x0, 0x0100);
- */
- miiphy_write(dev->name, phyAddr, 0x0, 0x0180);
-
- timeout = 20;
- do { /* wait for link status to go down */
- udelay(10000);
- if ((timeout--) == 0) {
-#if (DEBUG & 0x2)
- printf("hmmm, should not have waited...");
-#endif
- break;
- }
- miiphy_read(dev->name, phyAddr, 0x1, &phyStatus);
-#if (DEBUG & 0x2)
- printf("=");
-#endif
- } while ((phyStatus & 0x0004)); /* !link up */
-
- timeout = 1000;
- do { /* wait for link status to come back up */
- udelay(10000);
- if ((timeout--) == 0) {
- printf("failed. Link is down.\n");
- break;
- }
- miiphy_read(dev->name, phyAddr, 0x1, &phyStatus);
-#if (DEBUG & 0x2)
- printf("+");
-#endif
- } while (!(phyStatus & 0x0004)); /* !link up */
-
-#if (DEBUG & 0x2)
- printf ("done.\n");
-#endif
- } else { /* MII100 */
- /*
- * Set the auto-negotiation advertisement register bits
- */
- miiphy_write(dev->name, phyAddr, 0x4, 0x01e1);
-
- /*
- * Set MDIO bit 0.12 = 1(&& bit 0.9=1?) to enable auto-negotiation
- */
- miiphy_write(dev->name, phyAddr, 0x0, 0x1200);
-
- /*
- * Wait for AN completion
- */
- timeout = 5000;
- do {
- udelay(1000);
-
- if ((timeout--) == 0) {
-#if (DEBUG & 0x2)
- printf("PHY auto neg 0 failed...\n");
-#endif
- return -1;
- }
-
- if (miiphy_read(dev->name, phyAddr, 0x1, &phyStatus) != 0) {
-#if (DEBUG & 0x2)
- printf("PHY auto neg 1 failed 0x%04x...\n", phyStatus);
-#endif
- return -1;
- }
- } while (!(phyStatus & 0x0004));
-
-#if (DEBUG & 0x2)
- printf("PHY auto neg complete! \n");
-#endif
- }
-
- }
-
-#if (DEBUG & 0x2)
- if (fec->xcv_type != SEVENWIRE)
- mpc5xxx_fec_phydump (dev->name);
-#endif
-
-
-#if (DEBUG & 0x1)
- printf("mpc5xxx_fec_init_phy... Done \n");
-#endif
-
- return 1;
-}
-
-/********************************************************************/
-static void mpc5xxx_fec_halt(struct eth_device *dev)
-{
-#if defined(CONFIG_MPC5200)
- struct mpc5xxx_sdma *sdma = (struct mpc5xxx_sdma *)MPC5XXX_SDMA;
-#endif
- mpc5xxx_fec_priv *fec = (mpc5xxx_fec_priv *)dev->priv;
- int counter = 0xffff;
-
-#if (DEBUG & 0x2)
- if (fec->xcv_type != SEVENWIRE)
- mpc5xxx_fec_phydump (dev->name);
-#endif
-
- /*
- * mask FEC chip interrupts
- */
- fec->eth->imask = 0;
-
- /*
- * issue graceful stop command to the FEC transmitter if necessary
- */
- fec->eth->x_cntrl |= 0x00000001;
-
- /*
- * wait for graceful stop to register
- */
- while ((counter--) && (!(fec->eth->ievent & 0x10000000))) ;
-
- /*
- * Disable SmartDMA tasks
- */
- SDMA_TASK_DISABLE (FEC_XMIT_TASK_NO);
- SDMA_TASK_DISABLE (FEC_RECV_TASK_NO);
-
-#if defined(CONFIG_MPC5200)
- /*
- * Turn on COMM bus prefetch in the MGT5200 BestComm after we're
- * done. It doesn't work w/ the current receive task.
- */
- sdma->PtdCntrl &= ~0x00000001;
-#endif
-
- /*
- * Disable the Ethernet Controller
- */
- fec->eth->ecntrl &= 0xfffffffd;
-
- /*
- * Clear FIFO status registers
- */
- fec->eth->rfifo_status &= 0x00700000;
- fec->eth->tfifo_status &= 0x00700000;
-
- fec->eth->reset_cntrl = 0x01000000;
-
- /*
- * Issue a reset command to the FEC chip
- */
- fec->eth->ecntrl |= 0x1;
-
- /*
- * wait at least 16 clock cycles
- */
- udelay(10);
-
-#if (DEBUG & 0x3)
- printf("Ethernet task stopped\n");
-#endif
-}
-
-#if (DEBUG & 0x60)
-/********************************************************************/
-
-static void tfifo_print(char *devname, mpc5xxx_fec_priv *fec)
-{
- uint16 phyAddr = CONFIG_PHY_ADDR;
- uint16 phyStatus;
-
- if ((fec->eth->tfifo_lrf_ptr != fec->eth->tfifo_lwf_ptr)
- || (fec->eth->tfifo_rdptr != fec->eth->tfifo_wrptr)) {
-
- miiphy_read(devname, phyAddr, 0x1, &phyStatus);
- printf("\nphyStatus: 0x%04x\n", phyStatus);
- printf("ecntrl: 0x%08x\n", fec->eth->ecntrl);
- printf("ievent: 0x%08x\n", fec->eth->ievent);
- printf("x_status: 0x%08x\n", fec->eth->x_status);
- printf("tfifo: status 0x%08x\n", fec->eth->tfifo_status);
-
- printf(" control 0x%08x\n", fec->eth->tfifo_cntrl);
- printf(" lrfp 0x%08x\n", fec->eth->tfifo_lrf_ptr);
- printf(" lwfp 0x%08x\n", fec->eth->tfifo_lwf_ptr);
- printf(" alarm 0x%08x\n", fec->eth->tfifo_alarm);
- printf(" readptr 0x%08x\n", fec->eth->tfifo_rdptr);
- printf(" writptr 0x%08x\n", fec->eth->tfifo_wrptr);
- }
-}
-
-static void rfifo_print(char *devname, mpc5xxx_fec_priv *fec)
-{
- uint16 phyAddr = CONFIG_PHY_ADDR;
- uint16 phyStatus;
-
- if ((fec->eth->rfifo_lrf_ptr != fec->eth->rfifo_lwf_ptr)
- || (fec->eth->rfifo_rdptr != fec->eth->rfifo_wrptr)) {
-
- miiphy_read(devname, phyAddr, 0x1, &phyStatus);
- printf("\nphyStatus: 0x%04x\n", phyStatus);
- printf("ecntrl: 0x%08x\n", fec->eth->ecntrl);
- printf("ievent: 0x%08x\n", fec->eth->ievent);
- printf("x_status: 0x%08x\n", fec->eth->x_status);
- printf("rfifo: status 0x%08x\n", fec->eth->rfifo_status);
-
- printf(" control 0x%08x\n", fec->eth->rfifo_cntrl);
- printf(" lrfp 0x%08x\n", fec->eth->rfifo_lrf_ptr);
- printf(" lwfp 0x%08x\n", fec->eth->rfifo_lwf_ptr);
- printf(" alarm 0x%08x\n", fec->eth->rfifo_alarm);
- printf(" readptr 0x%08x\n", fec->eth->rfifo_rdptr);
- printf(" writptr 0x%08x\n", fec->eth->rfifo_wrptr);
- }
-}
-#endif /* DEBUG */
-
-/********************************************************************/
-
-static int mpc5xxx_fec_send(struct eth_device *dev, volatile void *eth_data,
- int data_length)
-{
- /*
- * This routine transmits one frame. This routine only accepts
- * 6-byte Ethernet addresses.
- */
- mpc5xxx_fec_priv *fec = (mpc5xxx_fec_priv *)dev->priv;
- volatile FEC_TBD *pTbd;
-
-#if (DEBUG & 0x20)
- printf("tbd status: 0x%04x\n", fec->tbdBase[0].status);
- tfifo_print(dev->name, fec);
-#endif
-
- /*
- * Clear Tx BD ring at first
- */
- mpc5xxx_fec_tbd_scrub(fec);
-
- /*
- * Check for valid length of data.
- */
- if ((data_length > 1500) || (data_length <= 0)) {
- return -1;
- }
-
- /*
- * Check the number of vacant TxBDs.
- */
- if (fec->cleanTbdNum < 1) {
-#if (DEBUG & 0x20)
- printf("No available TxBDs ...\n");
-#endif
- return -1;
- }
-
- /*
- * Get the first TxBD to send the mac header
- */
- pTbd = &fec->tbdBase[fec->tbdIndex];
- pTbd->dataLength = data_length;
- pTbd->dataPointer = (uint32)eth_data;
- pTbd->status |= FEC_TBD_LAST | FEC_TBD_TC | FEC_TBD_READY;
- fec->tbdIndex = (fec->tbdIndex + 1) % FEC_TBD_NUM;
-
-#if (DEBUG & 0x100)
- printf("SDMA_TASK_ENABLE, fec->tbdIndex = %d \n", fec->tbdIndex);
-#endif
-
- /*
- * Kick the MII i/f
- */
- if (fec->xcv_type != SEVENWIRE) {
- uint16 phyStatus;
- miiphy_read(dev->name, 0, 0x1, &phyStatus);
- }
-
- /*
- * Enable SmartDMA transmit task
- */
-
-#if (DEBUG & 0x20)
- tfifo_print(dev->name, fec);
-#endif
- SDMA_TASK_ENABLE (FEC_XMIT_TASK_NO);
-#if (DEBUG & 0x20)
- tfifo_print(dev->name, fec);
-#endif
-#if (DEBUG & 0x8)
- printf( "+" );
-#endif
-
- fec->cleanTbdNum -= 1;
-
-#if (DEBUG & 0x129) && (DEBUG & 0x80000000)
- printf ("smartDMA ethernet Tx task enabled\n");
-#endif
- /*
- * wait until frame is sent .
- */
- while (pTbd->status & FEC_TBD_READY) {
- udelay(10);
-#if (DEBUG & 0x8)
- printf ("TDB status = %04x\n", pTbd->status);
-#endif
- }
-
- return 0;
-}
-
-
-/********************************************************************/
-static int mpc5xxx_fec_recv(struct eth_device *dev)
-{
- /*
- * This command pulls one frame from the card
- */
- mpc5xxx_fec_priv *fec = (mpc5xxx_fec_priv *)dev->priv;
- volatile FEC_RBD *pRbd = &fec->rbdBase[fec->rbdIndex];
- unsigned long ievent;
- int frame_length, len = 0;
- NBUF *frame;
- uchar buff[FEC_MAX_PKT_SIZE];
-
-#if (DEBUG & 0x1)
- printf ("mpc5xxx_fec_recv %d Start...\n", fec->rbdIndex);
-#endif
-#if (DEBUG & 0x8)
- printf( "-" );
-#endif
-
- /*
- * Check if any critical events have happened
- */
- ievent = fec->eth->ievent;
- fec->eth->ievent = ievent;
- if (ievent & 0x20060000) {
- /* BABT, Rx/Tx FIFO errors */
- mpc5xxx_fec_halt(dev);
- mpc5xxx_fec_init(dev, NULL);
- return 0;
- }
- if (ievent & 0x80000000) {
- /* Heartbeat error */
- fec->eth->x_cntrl |= 0x00000001;
- }
- if (ievent & 0x10000000) {
- /* Graceful stop complete */
- if (fec->eth->x_cntrl & 0x00000001) {
- mpc5xxx_fec_halt(dev);
- fec->eth->x_cntrl &= ~0x00000001;
- mpc5xxx_fec_init(dev, NULL);
- }
- }
-
- if (!(pRbd->status & FEC_RBD_EMPTY)) {
- if ((pRbd->status & FEC_RBD_LAST) && !(pRbd->status & FEC_RBD_ERR) &&
- ((pRbd->dataLength - 4) > 14)) {
-
- /*
- * Get buffer address and size
- */
- frame = (NBUF *)pRbd->dataPointer;
- frame_length = pRbd->dataLength - 4;
-
-#if (DEBUG & 0x20)
- {
- int i;
- printf("recv data hdr:");
- for (i = 0; i < 14; i++)
- printf("%x ", *(frame->head + i));
- printf("\n");
- }
-#endif
- /*
- * Fill the buffer and pass it to upper layers
- */
- memcpy(buff, frame->head, 14);
- memcpy(buff + 14, frame->data, frame_length);
- NetReceive(buff, frame_length);
- len = frame_length;
- }
- /*
- * Reset buffer descriptor as empty
- */
- mpc5xxx_fec_rbd_clean(fec, pRbd);
- }
- SDMA_CLEAR_IEVENT (FEC_RECV_TASK_NO);
- return len;
-}
-
-
-/********************************************************************/
-int mpc5xxx_fec_initialize(bd_t * bis)
-{
- mpc5xxx_fec_priv *fec;
- struct eth_device *dev;
- char *tmp, *end;
- char env_enetaddr[6];
- int i;
-
- fec = (mpc5xxx_fec_priv *)malloc(sizeof(*fec));
- dev = (struct eth_device *)malloc(sizeof(*dev));
- memset(dev, 0, sizeof *dev);
-
- fec->eth = (ethernet_regs *)MPC5XXX_FEC;
- fec->tbdBase = (FEC_TBD *)FEC_BD_BASE;
- fec->rbdBase = (FEC_RBD *)(FEC_BD_BASE + FEC_TBD_NUM * sizeof(FEC_TBD));
-#if defined(CONFIG_CANMB) || \
- defined(CONFIG_CM5200) || \
- defined(CONFIG_HMI1001) || \
- defined(CONFIG_ICECUBE) || \
- defined(CONFIG_INKA4X0) || \
- defined(CONFIG_JUPITER) || \
- defined(CONFIG_MCC200) || \
- defined(CONFIG_MOTIONPRO) || \
- defined(CONFIG_MUCMC52) || \
- defined(CONFIG_O2DNT) || \
- defined(CONFIG_PM520) || \
- defined(CONFIG_TOP5200) || \
- defined(CONFIG_TQM5200) || \
- defined(CONFIG_UC101) || \
- defined(CONFIG_V38B) || \
- defined(CONFIG_MUNICES)
-# ifndef CONFIG_FEC_10MBIT
- fec->xcv_type = MII100;
-# else
- fec->xcv_type = MII10;
-# endif
-#elif defined(CONFIG_TOTAL5200)
- fec->xcv_type = SEVENWIRE;
-#else
-#error fec->xcv_type not initialized.
-#endif
-
- dev->priv = (void *)fec;
- dev->iobase = MPC5XXX_FEC;
- dev->init = mpc5xxx_fec_init;
- dev->halt = mpc5xxx_fec_halt;
- dev->send = mpc5xxx_fec_send;
- dev->recv = mpc5xxx_fec_recv;
-
- sprintf(dev->name, "FEC ETHERNET");
- eth_register(dev);
-
-#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
- miiphy_register (dev->name,
- fec5xxx_miiphy_read, fec5xxx_miiphy_write);
-#endif
-
- /*
- * Try to set the mac address now. The fec mac address is
- * a garbage after reset. When not using fec for booting
- * the Linux fec driver will try to work with this garbage.
- */
- tmp = getenv("ethaddr");
- if (tmp) {
- for (i=0; i<6; i++) {
- env_enetaddr[i] = tmp ? simple_strtoul(tmp, &end, 16) : 0;
- if (tmp)
- tmp = (*end) ? end+1 : end;
- }
- mpc5xxx_fec_set_hwaddr(fec, env_enetaddr);
- }
-
- mpc5xxx_fec_init_phy(dev, bis);
-
- return 1;
-}
-
-/* MII-interface related functions */
-/********************************************************************/
-int fec5xxx_miiphy_read(char *devname, uint8 phyAddr, uint8 regAddr, uint16 * retVal)
-{
- ethernet_regs *eth = (ethernet_regs *)MPC5XXX_FEC;
- uint32 reg; /* convenient holder for the PHY register */
- uint32 phy; /* convenient holder for the PHY */
- int timeout = 0xffff;
-
- /*
- * reading from any PHY's register is done by properly
- * programming the FEC's MII data register.
- */
- reg = regAddr << FEC_MII_DATA_RA_SHIFT;
- phy = phyAddr << FEC_MII_DATA_PA_SHIFT;
-
- eth->mii_data = (FEC_MII_DATA_ST | FEC_MII_DATA_OP_RD | FEC_MII_DATA_TA | phy | reg);
-
- /*
- * wait for the related interrupt
- */
- while ((timeout--) && (!(eth->ievent & 0x00800000))) ;
-
- if (timeout == 0) {
-#if (DEBUG & 0x2)
- printf ("Read MDIO failed...\n");
-#endif
- return -1;
- }
-
- /*
- * clear mii interrupt bit
- */
- eth->ievent = 0x00800000;
-
- /*
- * it's now safe to read the PHY's register
- */
- *retVal = (uint16) eth->mii_data;
-
- return 0;
-}
-
-/********************************************************************/
-int fec5xxx_miiphy_write(char *devname, uint8 phyAddr, uint8 regAddr, uint16 data)
-{
- ethernet_regs *eth = (ethernet_regs *)MPC5XXX_FEC;
- uint32 reg; /* convenient holder for the PHY register */
- uint32 phy; /* convenient holder for the PHY */
- int timeout = 0xffff;
-
- reg = regAddr << FEC_MII_DATA_RA_SHIFT;
- phy = phyAddr << FEC_MII_DATA_PA_SHIFT;
-
- eth->mii_data = (FEC_MII_DATA_ST | FEC_MII_DATA_OP_WR |
- FEC_MII_DATA_TA | phy | reg | data);
-
- /*
- * wait for the MII interrupt
- */
- while ((timeout--) && (!(eth->ievent & 0x00800000))) ;
-
- if (timeout == 0) {
-#if (DEBUG & 0x2)
- printf ("Write MDIO failed...\n");
-#endif
- return -1;
- }
-
- /*
- * clear MII interrupt bit
- */
- eth->ievent = 0x00800000;
-
- return 0;
-}
-
-#if (DEBUG & 0x40)
-static uint32 local_crc32(char *string, unsigned int crc_value, int len)
-{
- int i;
- char c;
- unsigned int crc, count;
-
- /*
- * crc32 algorithm
- */
- /*
- * crc = 0xffffffff; * The initialized value should be 0xffffffff
- */
- crc = crc_value;
-
- for (i = len; --i >= 0;) {
- c = *string++;
- for (count = 0; count < 8; count++) {
- if ((c & 0x01) ^ (crc & 0x01)) {
- crc >>= 1;
- crc = crc ^ 0xedb88320;
- } else {
- crc >>= 1;
- }
- c >>= 1;
- }
- }
-
- /*
- * In big endian system, do byte swaping for crc value
- */
- /**/ return crc;
-}
-#endif /* DEBUG */
-
-#endif /* CONFIG_MPC5xxx_FEC */
diff --git a/cpu/mpc5xxx/fec.h b/cpu/mpc5xxx/fec.h
deleted file mode 100644
index 81756a5..0000000
--- a/cpu/mpc5xxx/fec.h
+++ /dev/null
@@ -1,286 +0,0 @@
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * This file is based on mpc4200fec.h
- * (C) Copyright Motorola, Inc., 2000
- *
- * odin ethernet header file
- */
-
-#ifndef __MPC5XXX_FEC_H
-#define __MPC5XXX_FEC_H
-
-#include <common.h>
-#include <mpc5xxx.h>
-#include "sdma.h"
-
-typedef unsigned long uint32;
-typedef unsigned short uint16;
-typedef unsigned char uint8;
-
-typedef struct ethernet_register_set {
-
-/* [10:2]addr = 00 */
-
-/* Control and status Registers (offset 000-1FF) */
-
- volatile uint32 fec_id; /* MBAR_ETH + 0x000 */
- volatile uint32 ievent; /* MBAR_ETH + 0x004 */
- volatile uint32 imask; /* MBAR_ETH + 0x008 */
-
- volatile uint32 RES0[1]; /* MBAR_ETH + 0x00C */
- volatile uint32 r_des_active; /* MBAR_ETH + 0x010 */
- volatile uint32 x_des_active; /* MBAR_ETH + 0x014 */
- volatile uint32 r_des_active_cl; /* MBAR_ETH + 0x018 */
- volatile uint32 x_des_active_cl; /* MBAR_ETH + 0x01C */
- volatile uint32 ivent_set; /* MBAR_ETH + 0x020 */
- volatile uint32 ecntrl; /* MBAR_ETH + 0x024 */
-
- volatile uint32 RES1[6]; /* MBAR_ETH + 0x028-03C */
- volatile uint32 mii_data; /* MBAR_ETH + 0x040 */
- volatile uint32 mii_speed; /* MBAR_ETH + 0x044 */
- volatile uint32 mii_status; /* MBAR_ETH + 0x048 */
-
- volatile uint32 RES2[5]; /* MBAR_ETH + 0x04C-05C */
- volatile uint32 mib_data; /* MBAR_ETH + 0x060 */
- volatile uint32 mib_control; /* MBAR_ETH + 0x064 */
-
- volatile uint32 RES3[6]; /* MBAR_ETH + 0x068-7C */
- volatile uint32 r_activate; /* MBAR_ETH + 0x080 */
- volatile uint32 r_cntrl; /* MBAR_ETH + 0x084 */
- volatile uint32 r_hash; /* MBAR_ETH + 0x088 */
- volatile uint32 r_data; /* MBAR_ETH + 0x08C */
- volatile uint32 ar_done; /* MBAR_ETH + 0x090 */
- volatile uint32 r_test; /* MBAR_ETH + 0x094 */
- volatile uint32 r_mib; /* MBAR_ETH + 0x098 */
- volatile uint32 r_da_low; /* MBAR_ETH + 0x09C */
- volatile uint32 r_da_high; /* MBAR_ETH + 0x0A0 */
-
- volatile uint32 RES4[7]; /* MBAR_ETH + 0x0A4-0BC */
- volatile uint32 x_activate; /* MBAR_ETH + 0x0C0 */
- volatile uint32 x_cntrl; /* MBAR_ETH + 0x0C4 */
- volatile uint32 backoff; /* MBAR_ETH + 0x0C8 */
- volatile uint32 x_data; /* MBAR_ETH + 0x0CC */
- volatile uint32 x_status; /* MBAR_ETH + 0x0D0 */
- volatile uint32 x_mib; /* MBAR_ETH + 0x0D4 */
- volatile uint32 x_test; /* MBAR_ETH + 0x0D8 */
- volatile uint32 fdxfc_da1; /* MBAR_ETH + 0x0DC */
- volatile uint32 fdxfc_da2; /* MBAR_ETH + 0x0E0 */
- volatile uint32 paddr1; /* MBAR_ETH + 0x0E4 */
- volatile uint32 paddr2; /* MBAR_ETH + 0x0E8 */
- volatile uint32 op_pause; /* MBAR_ETH + 0x0EC */
-
- volatile uint32 RES5[4]; /* MBAR_ETH + 0x0F0-0FC */
- volatile uint32 instr_reg; /* MBAR_ETH + 0x100 */
- volatile uint32 context_reg; /* MBAR_ETH + 0x104 */
- volatile uint32 test_cntrl; /* MBAR_ETH + 0x108 */
- volatile uint32 acc_reg; /* MBAR_ETH + 0x10C */
- volatile uint32 ones; /* MBAR_ETH + 0x110 */
- volatile uint32 zeros; /* MBAR_ETH + 0x114 */
- volatile uint32 iaddr1; /* MBAR_ETH + 0x118 */
- volatile uint32 iaddr2; /* MBAR_ETH + 0x11C */
- volatile uint32 gaddr1; /* MBAR_ETH + 0x120 */
- volatile uint32 gaddr2; /* MBAR_ETH + 0x124 */
- volatile uint32 random; /* MBAR_ETH + 0x128 */
- volatile uint32 rand1; /* MBAR_ETH + 0x12C */
- volatile uint32 tmp; /* MBAR_ETH + 0x130 */
-
- volatile uint32 RES6[3]; /* MBAR_ETH + 0x134-13C */
- volatile uint32 fifo_id; /* MBAR_ETH + 0x140 */
- volatile uint32 x_wmrk; /* MBAR_ETH + 0x144 */
- volatile uint32 fcntrl; /* MBAR_ETH + 0x148 */
- volatile uint32 r_bound; /* MBAR_ETH + 0x14C */
- volatile uint32 r_fstart; /* MBAR_ETH + 0x150 */
- volatile uint32 r_count; /* MBAR_ETH + 0x154 */
- volatile uint32 r_lag; /* MBAR_ETH + 0x158 */
- volatile uint32 r_read; /* MBAR_ETH + 0x15C */
- volatile uint32 r_write; /* MBAR_ETH + 0x160 */
- volatile uint32 x_count; /* MBAR_ETH + 0x164 */
- volatile uint32 x_lag; /* MBAR_ETH + 0x168 */
- volatile uint32 x_retry; /* MBAR_ETH + 0x16C */
- volatile uint32 x_write; /* MBAR_ETH + 0x170 */
- volatile uint32 x_read; /* MBAR_ETH + 0x174 */
-
- volatile uint32 RES7[2]; /* MBAR_ETH + 0x178-17C */
- volatile uint32 fm_cntrl; /* MBAR_ETH + 0x180 */
- volatile uint32 rfifo_data; /* MBAR_ETH + 0x184 */
- volatile uint32 rfifo_status; /* MBAR_ETH + 0x188 */
- volatile uint32 rfifo_cntrl; /* MBAR_ETH + 0x18C */
- volatile uint32 rfifo_lrf_ptr; /* MBAR_ETH + 0x190 */
- volatile uint32 rfifo_lwf_ptr; /* MBAR_ETH + 0x194 */
- volatile uint32 rfifo_alarm; /* MBAR_ETH + 0x198 */
- volatile uint32 rfifo_rdptr; /* MBAR_ETH + 0x19C */
- volatile uint32 rfifo_wrptr; /* MBAR_ETH + 0x1A0 */
- volatile uint32 tfifo_data; /* MBAR_ETH + 0x1A4 */
- volatile uint32 tfifo_status; /* MBAR_ETH + 0x1A8 */
- volatile uint32 tfifo_cntrl; /* MBAR_ETH + 0x1AC */
- volatile uint32 tfifo_lrf_ptr; /* MBAR_ETH + 0x1B0 */
- volatile uint32 tfifo_lwf_ptr; /* MBAR_ETH + 0x1B4 */
- volatile uint32 tfifo_alarm; /* MBAR_ETH + 0x1B8 */
- volatile uint32 tfifo_rdptr; /* MBAR_ETH + 0x1BC */
- volatile uint32 tfifo_wrptr; /* MBAR_ETH + 0x1C0 */
-
- volatile uint32 reset_cntrl; /* MBAR_ETH + 0x1C4 */
- volatile uint32 xmit_fsm; /* MBAR_ETH + 0x1C8 */
-
- volatile uint32 RES8[3]; /* MBAR_ETH + 0x1CC-1D4 */
- volatile uint32 rdes_data0; /* MBAR_ETH + 0x1D8 */
- volatile uint32 rdes_data1; /* MBAR_ETH + 0x1DC */
- volatile uint32 r_length; /* MBAR_ETH + 0x1E0 */
- volatile uint32 x_length; /* MBAR_ETH + 0x1E4 */
- volatile uint32 x_addr; /* MBAR_ETH + 0x1E8 */
- volatile uint32 cdes_data; /* MBAR_ETH + 0x1EC */
- volatile uint32 status; /* MBAR_ETH + 0x1F0 */
- volatile uint32 dma_control; /* MBAR_ETH + 0x1F4 */
- volatile uint32 des_cmnd; /* MBAR_ETH + 0x1F8 */
- volatile uint32 data; /* MBAR_ETH + 0x1FC */
-
-/* MIB COUNTERS (Offset 200-2FF) */
-
- volatile uint32 rmon_t_drop; /* MBAR_ETH + 0x200 */
- volatile uint32 rmon_t_packets; /* MBAR_ETH + 0x204 */
- volatile uint32 rmon_t_bc_pkt; /* MBAR_ETH + 0x208 */
- volatile uint32 rmon_t_mc_pkt; /* MBAR_ETH + 0x20C */
- volatile uint32 rmon_t_crc_align; /* MBAR_ETH + 0x210 */
- volatile uint32 rmon_t_undersize; /* MBAR_ETH + 0x214 */
- volatile uint32 rmon_t_oversize; /* MBAR_ETH + 0x218 */
- volatile uint32 rmon_t_frag; /* MBAR_ETH + 0x21C */
- volatile uint32 rmon_t_jab; /* MBAR_ETH + 0x220 */
- volatile uint32 rmon_t_col; /* MBAR_ETH + 0x224 */
- volatile uint32 rmon_t_p64; /* MBAR_ETH + 0x228 */
- volatile uint32 rmon_t_p65to127; /* MBAR_ETH + 0x22C */
- volatile uint32 rmon_t_p128to255; /* MBAR_ETH + 0x230 */
- volatile uint32 rmon_t_p256to511; /* MBAR_ETH + 0x234 */
- volatile uint32 rmon_t_p512to1023; /* MBAR_ETH + 0x238 */
- volatile uint32 rmon_t_p1024to2047; /* MBAR_ETH + 0x23C */
- volatile uint32 rmon_t_p_gte2048; /* MBAR_ETH + 0x240 */
- volatile uint32 rmon_t_octets; /* MBAR_ETH + 0x244 */
- volatile uint32 ieee_t_drop; /* MBAR_ETH + 0x248 */
- volatile uint32 ieee_t_frame_ok; /* MBAR_ETH + 0x24C */
- volatile uint32 ieee_t_1col; /* MBAR_ETH + 0x250 */
- volatile uint32 ieee_t_mcol; /* MBAR_ETH + 0x254 */
- volatile uint32 ieee_t_def; /* MBAR_ETH + 0x258 */
- volatile uint32 ieee_t_lcol; /* MBAR_ETH + 0x25C */
- volatile uint32 ieee_t_excol; /* MBAR_ETH + 0x260 */
- volatile uint32 ieee_t_macerr; /* MBAR_ETH + 0x264 */
- volatile uint32 ieee_t_cserr; /* MBAR_ETH + 0x268 */
- volatile uint32 ieee_t_sqe; /* MBAR_ETH + 0x26C */
- volatile uint32 t_fdxfc; /* MBAR_ETH + 0x270 */
- volatile uint32 ieee_t_octets_ok; /* MBAR_ETH + 0x274 */
-
- volatile uint32 RES9[2]; /* MBAR_ETH + 0x278-27C */
- volatile uint32 rmon_r_drop; /* MBAR_ETH + 0x280 */
- volatile uint32 rmon_r_packets; /* MBAR_ETH + 0x284 */
- volatile uint32 rmon_r_bc_pkt; /* MBAR_ETH + 0x288 */
- volatile uint32 rmon_r_mc_pkt; /* MBAR_ETH + 0x28C */
- volatile uint32 rmon_r_crc_align; /* MBAR_ETH + 0x290 */
- volatile uint32 rmon_r_undersize; /* MBAR_ETH + 0x294 */
- volatile uint32 rmon_r_oversize; /* MBAR_ETH + 0x298 */
- volatile uint32 rmon_r_frag; /* MBAR_ETH + 0x29C */
- volatile uint32 rmon_r_jab; /* MBAR_ETH + 0x2A0 */
-
- volatile uint32 rmon_r_resvd_0; /* MBAR_ETH + 0x2A4 */
-
- volatile uint32 rmon_r_p64; /* MBAR_ETH + 0x2A8 */
- volatile uint32 rmon_r_p65to127; /* MBAR_ETH + 0x2AC */
- volatile uint32 rmon_r_p128to255; /* MBAR_ETH + 0x2B0 */
- volatile uint32 rmon_r_p256to511; /* MBAR_ETH + 0x2B4 */
- volatile uint32 rmon_r_p512to1023; /* MBAR_ETH + 0x2B8 */
- volatile uint32 rmon_r_p1024to2047; /* MBAR_ETH + 0x2BC */
- volatile uint32 rmon_r_p_gte2048; /* MBAR_ETH + 0x2C0 */
- volatile uint32 rmon_r_octets; /* MBAR_ETH + 0x2C4 */
- volatile uint32 ieee_r_drop; /* MBAR_ETH + 0x2C8 */
- volatile uint32 ieee_r_frame_ok; /* MBAR_ETH + 0x2CC */
- volatile uint32 ieee_r_crc; /* MBAR_ETH + 0x2D0 */
- volatile uint32 ieee_r_align; /* MBAR_ETH + 0x2D4 */
- volatile uint32 r_macerr; /* MBAR_ETH + 0x2D8 */
- volatile uint32 r_fdxfc; /* MBAR_ETH + 0x2DC */
- volatile uint32 ieee_r_octets_ok; /* MBAR_ETH + 0x2E0 */
-
- volatile uint32 RES10[6]; /* MBAR_ETH + 0x2E4-2FC */
-
- volatile uint32 RES11[64]; /* MBAR_ETH + 0x300-3FF */
-} ethernet_regs;
-
-/* Receive & Transmit Buffer Descriptor definitions */
-typedef struct BufferDescriptor {
- uint16 status;
- uint16 dataLength;
- uint32 dataPointer;
-} FEC_RBD;
-typedef struct {
- uint16 status;
- uint16 dataLength;
- uint32 dataPointer;
-} FEC_TBD;
-
-/* private structure */
-typedef enum {
- SEVENWIRE, /* 7-wire */
- MII10, /* MII 10Mbps */
- MII100 /* MII 100Mbps */
-} xceiver_type;
-
-typedef struct {
- ethernet_regs *eth;
- xceiver_type xcv_type; /* transceiver type */
- FEC_RBD *rbdBase; /* RBD ring */
- FEC_TBD *tbdBase; /* TBD ring */
- uint16 rbdIndex; /* next receive BD to read */
- uint16 tbdIndex; /* next transmit BD to send */
- uint16 usedTbdIndex; /* next transmit BD to clean */
- uint16 cleanTbdNum; /* the number of available transmit BDs */
-} mpc5xxx_fec_priv;
-
-/* Ethernet parameter area */
-#define FEC_TBD_BASE (FEC_PARAM_BASE + 0x00)
-#define FEC_TBD_NEXT (FEC_PARAM_BASE + 0x04)
-#define FEC_RBD_BASE (FEC_PARAM_BASE + 0x08)
-#define FEC_RBD_NEXT (FEC_PARAM_BASE + 0x0c)
-
-/* BD Numer definitions */
-#define FEC_TBD_NUM 48 /* The user can adjust this value */
-#define FEC_RBD_NUM 32 /* The user can adjust this value */
-
-/* packet size limit */
-#define FEC_MAX_PKT_SIZE 1536
-
-/* RBD bits definitions */
-#define FEC_RBD_EMPTY 0x8000 /* Buffer is empty */
-#define FEC_RBD_WRAP 0x2000 /* Last BD in ring */
-#define FEC_RBD_INT 0x1000 /* Interrupt */
-#define FEC_RBD_LAST 0x0800 /* Buffer is last in frame(useless) */
-#define FEC_RBD_MISS 0x0100 /* Miss bit for prom mode */
-#define FEC_RBD_BC 0x0080 /* The received frame is broadcast frame */
-#define FEC_RBD_MC 0x0040 /* The received frame is multicast frame */
-#define FEC_RBD_LG 0x0020 /* Frame length violation */
-#define FEC_RBD_NO 0x0010 /* Nonoctet align frame */
-#define FEC_RBD_SH 0x0008 /* Short frame */
-#define FEC_RBD_CR 0x0004 /* CRC error */
-#define FEC_RBD_OV 0x0002 /* Receive FIFO overrun */
-#define FEC_RBD_TR 0x0001 /* Frame is truncated */
-#define FEC_RBD_ERR (FEC_RBD_LG | FEC_RBD_NO | FEC_RBD_CR | \
- FEC_RBD_OV | FEC_RBD_TR)
-
-/* TBD bits definitions */
-#define FEC_TBD_READY 0x8000 /* Buffer is ready */
-#define FEC_TBD_WRAP 0x2000 /* Last BD in ring */
-#define FEC_TBD_INT 0x1000 /* Interrupt */
-#define FEC_TBD_LAST 0x0800 /* Buffer is last in frame */
-#define FEC_TBD_TC 0x0400 /* Transmit the CRC */
-#define FEC_TBD_ABC 0x0200 /* Append bad CRC */
-
-/* MII-related definitios */
-#define FEC_MII_DATA_ST 0x40000000 /* Start of frame delimiter */
-#define FEC_MII_DATA_OP_RD 0x20000000 /* Perform a read operation */
-#define FEC_MII_DATA_OP_WR 0x10000000 /* Perform a write operation */
-#define FEC_MII_DATA_PA_MSK 0x0f800000 /* PHY Address field mask */
-#define FEC_MII_DATA_RA_MSK 0x007c0000 /* PHY Register field mask */
-#define FEC_MII_DATA_TA 0x00020000 /* Turnaround */
-#define FEC_MII_DATA_DATAMSK 0x0000ffff /* PHY data field */
-
-#define FEC_MII_DATA_RA_SHIFT 18 /* MII Register address bits */
-#define FEC_MII_DATA_PA_SHIFT 23 /* MII PHY address bits */
-
-#endif /* __MPC5XXX_FEC_H */
diff --git a/cpu/mpc5xxx/sdma.h b/cpu/mpc5xxx/sdma.h
deleted file mode 100644
index 8b740e4..0000000
--- a/cpu/mpc5xxx/sdma.h
+++ /dev/null
@@ -1,93 +0,0 @@
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * This file is based on code
- * (C) Copyright Motorola, Inc., 2000
- *
- * odin smartdma header file
- */
-
-#ifndef __MPC5XXX_SDMA_H
-#define __MPC5XXX_SDMA_H
-
-#include <common.h>
-#include <mpc5xxx.h>
-
-/* Task number assignment */
-#define FEC_RECV_TASK_NO 0
-#define FEC_XMIT_TASK_NO 1
-
-/*---------------------------------------------------------------------*/
-
-/* Stuff for Ethernet Tx/Rx tasks */
-
-/*---------------------------------------------------------------------*/
-
-/* Layout of Ethernet controller Parameter SRAM area:
-----------------------------------------------------------------
-0x00: TBD_BASE, base address of TX BD ring
-0x04: TBD_NEXT, address of next TX BD to be processed
-0x08: RBD_BASE, base address of RX BD ring
-0x0C: RBD_NEXT, address of next RX BD to be processed
----------------------------------------------------------------
-ALL PARAMETERS ARE ALL LONGWORDS (FOUR BYTES EACH).
-*/
-
-/* base address of SRAM area to store parameters used by Ethernet tasks */
-#define FEC_PARAM_BASE (MPC5XXX_SRAM + 0x0800)
-
-/* base address of SRAM area for buffer descriptors */
-#define FEC_BD_BASE (MPC5XXX_SRAM + 0x0820)
-
-/*---------------------------------------------------------------------*/
-
-/* common shortcuts used by driver C code */
-
-/*---------------------------------------------------------------------*/
-
-/* Disable SmartDMA task */
-#define SDMA_TASK_DISABLE(tasknum) \
-{ \
- volatile ushort *tcr = (ushort *)(MPC5XXX_SDMA + 0x0000001c + 2 * tasknum); \
- *tcr = (*tcr) & (~0x8000); \
-}
-
-/* Enable SmartDMA task */
-#define SDMA_TASK_ENABLE(tasknum) \
-{ \
- volatile ushort *tcr = (ushort *) (MPC5XXX_SDMA + 0x0000001c + 2 * tasknum); \
- *tcr = (*tcr) | 0x8000; \
-}
-
-/* Enable interrupt */
-#define SDMA_INT_ENABLE(tasknum) \
-{ \
- struct mpc5xxx_sdma *sdma = (struct mpc5xxx_sdma *)MPC5XXX_SDMA; \
- sdma->IntMask &= ~(1 << tasknum); \
-}
-
-/* Disable interrupt */
-#define SDMA_INT_DISABLE(tasknum) \
-{ \
- struct mpc5xxx_sdma *sdma = (struct mpc5xxx_sdma *)MPC5XXX_SDMA; \
- sdma->IntMask |= (1 << tasknum); \
-}
-
-
-/* Clear interrupt pending bits */
-#define SDMA_CLEAR_IEVENT(tasknum) \
-{ \
- struct mpc5xxx_sdma *sdma = (struct mpc5xxx_sdma *)MPC5XXX_SDMA; \
- sdma->IntPend = (1 << tasknum); \
-}
-
-/* get interupt pending bit of a task */
-#define SDMA_GET_PENDINGBIT(tasknum) \
- ((*(vu_long *)(MPC5XXX_SDMA + 0x14)) & (1<<(tasknum)))
-
-/* get interupt mask bit of a task */
-#define SDMA_GET_MASKBIT(tasknum) \
- ((*(vu_long *)(MPC5XXX_SDMA + 0x18)) & (1<<(tasknum)))
-
-#endif /* __MPC5XXX_SDMA_H */
diff --git a/cpu/sh2/Makefile b/cpu/sh2/Makefile
new file mode 100644
index 0000000..50f6720
--- /dev/null
+++ b/cpu/sh2/Makefile
@@ -0,0 +1,49 @@
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# Copyright (C) 2007,2008 Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+# Copyright (C) 2008 Renesas Solutions Corp.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(CPU).a
+
+START = start.o
+OBJS = cpu.o interrupts.o watchdog.o time.o # cache.o
+
+all: .depend $(START) $(LIB)
+
+$(LIB): $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+#########################################################################
+
+.depend: Makefile $(START:.o=.S) $(OBJS:.o=.c)
+ $(CC) -M $(CFLAGS) $(START:.o=.S) $(OBJS:.o=.c) > $@
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/cpu/sh2/cache.c b/cpu/sh2/cache.c
new file mode 100644
index 0000000..b5c47cf
--- /dev/null
+++ b/cpu/sh2/cache.c
@@ -0,0 +1,112 @@
+/*
+ * (C) Copyright 2007
+ * Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
+ *
+ * Copyright (C) 2007, 2008 Nobobuhiro Iwamatsu <iwamatsu@nigauri.org>
+ * Copyright (C) 2008 Renesas Solutions Corp.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+
+/*
+ * Jump to P2 area.
+ * When handling TLB or caches, we need to do it from P2 area.
+ */
+#define jump_to_P2() \
+do { \
+ unsigned long __dummy; \
+ __asm__ __volatile__( \
+ "mov.l 1f, %0\n\t" \
+ "or %1, %0\n\t" \
+ "jmp @%0\n\t" \
+ " nop\n\t" \
+ ".balign 4\n" \
+ "1: .long 2f\n" \
+ "2:" \
+ : "=&r" (__dummy) \
+ : "r" (0x20000000)); \
+} while (0)
+
+/*
+ * Back to P1 area.
+ */
+#define back_to_P1() \
+do { \
+ unsigned long __dummy; \
+ __asm__ __volatile__( \
+ "nop;nop;nop;nop;nop;nop;nop\n\t" \
+ "mov.l 1f, %0\n\t" \
+ "jmp @%0\n\t" \
+ " nop\n\t" \
+ ".balign 4\n" \
+ "1: .long 2f\n" \
+ "2:" \
+ : "=&r" (__dummy)); \
+} while (0)
+
+#define CACHE_VALID 1
+#define CACHE_UPDATED 2
+
+static inline void cache_wback_all(void)
+{
+ unsigned long addr, data, i, j;
+
+ jump_to_P2();
+ for (i = 0; i < CACHE_OC_NUM_ENTRIES; i++) {
+ for (j = 0; j < CACHE_OC_NUM_WAYS; j++) {
+ addr = CACHE_OC_ADDRESS_ARRAY
+ | (j << CACHE_OC_WAY_SHIFT)
+ | (i << CACHE_OC_ENTRY_SHIFT);
+ data = inl(addr);
+ if (data & CACHE_UPDATED) {
+ data &= ~CACHE_UPDATED;
+ outl(data, addr);
+ }
+ }
+ }
+ back_to_P1();
+}
+
+
+#define CACHE_ENABLE 0
+#define CACHE_DISABLE 1
+
+int cache_control(unsigned int cmd)
+{
+ unsigned long ccr;
+
+ jump_to_P2();
+ ccr = inl(CCR);
+
+ if (ccr & CCR_CACHE_ENABLE)
+ cache_wback_all();
+
+ if (cmd == CACHE_DISABLE)
+ outl(CCR_CACHE_STOP, CCR);
+ else
+ outl(CCR_CACHE_INIT, CCR);
+ back_to_P1();
+
+ return 0;
+}
diff --git a/cpu/sh2/config.mk b/cpu/sh2/config.mk
new file mode 100644
index 0000000..52d5a0f
--- /dev/null
+++ b/cpu/sh2/config.mk
@@ -0,0 +1,26 @@
+#
+# (C) Copyright 2007-2008
+# Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+#
+PLATFORM_CPPFLAGS += -m3e -mb
+PLATFORM_RELFLAGS += -ffixed-r13
+PLATFORM_LDFLAGS += -EB
diff --git a/cpu/sh2/cpu.c b/cpu/sh2/cpu.c
new file mode 100644
index 0000000..e0cb047
--- /dev/null
+++ b/cpu/sh2/cpu.c
@@ -0,0 +1,98 @@
+/*
+ * Copyright (C) 2007,2008 Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+ * Copyright (C) 2008 Renesas Solutions Corp.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+
+#define STBCR4 0xFFFE040C
+#define cmt_clock_enable() do {\
+ writeb(readb(STBCR4) & ~0x04, STBCR4);\
+ } while (0)
+#define scif0_enable() do {\
+ writeb(readb(STBCR4) & ~0x80, STBCR4);\
+ } while (0)
+
+int checkcpu(void)
+{
+#if defined(CONFIG_SH2A)
+ puts("CPU: SH2A\n");
+#else
+ puts("CPU: SH2\n");
+#endif
+ return 0;
+}
+
+int cpu_init(void)
+{
+ /* SCIF enable */
+ scif0_enable();
+ /* CMT clock enable */
+ cmt_clock_enable() ;
+ return 0;
+}
+
+int cleanup_before_linux(void)
+{
+ disable_interrupts();
+ return 0;
+}
+
+int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+ disable_interrupts();
+ reset_cpu(0);
+ return 0;
+}
+
+void flush_cache(unsigned long addr, unsigned long size)
+{
+
+}
+
+void icache_enable(void)
+{
+}
+
+void icache_disable(void)
+{
+}
+
+int icache_status(void)
+{
+ return 0;
+}
+
+void dcache_enable(void)
+{
+}
+
+void dcache_disable(void)
+{
+}
+
+int dcache_status(void)
+{
+ return 0;
+}
diff --git a/cpu/sh2/interrupts.c b/cpu/sh2/interrupts.c
new file mode 100644
index 0000000..fe6ff3a
--- /dev/null
+++ b/cpu/sh2/interrupts.c
@@ -0,0 +1,39 @@
+/*
+ * Copyright 2007,2008 Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+ * Copyright (C) 2008 Renesas Solutions Corp.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+int interrupt_init(void)
+{
+ return 0;
+}
+
+void enable_interrupts(void)
+{
+
+}
+
+int disable_interrupts(void)
+{
+ return 0;
+}
diff --git a/cpu/sh2/start.S b/cpu/sh2/start.S
new file mode 100644
index 0000000..c4fa688
--- /dev/null
+++ b/cpu/sh2/start.S
@@ -0,0 +1,78 @@
+/*
+ * Copyright (C) 2007,2008 Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+ * Copyright (C) 2008 Renesas Solutions Corp.
+
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+
+ .text
+ .align 2
+
+ .global _start
+_start:
+ .long 0x00000010 /* Ppower ON reset PC*/
+ .long 0x00000000
+ .long 0x00000010 /* Manual reset PC */
+ .long 0x00000000
+_init:
+ mov.l ._lowlevel_init, r0
+100: bsrf r0
+ nop
+ bsr 1f
+ nop
+1: sts pr, r5
+ mov.l ._reloc_dst, r4
+ add #(_start-1b), r5
+ mov.l ._reloc_dst_end, r6
+
+2: mov.l @r5+, r1
+ mov.l r1, @r4
+ add #4, r4
+ cmp/hs r6, r4
+ bf 2b
+
+ mov.l ._bss_start, r4
+ mov.l ._bss_end, r5
+ mov #0, r1
+
+3: mov.l r1, @r4 /* bss clear */
+ add #4, r4
+ cmp/hs r5, r4
+ bf 3b
+
+ mov.l ._gd_init, r13 /* global data */
+ mov.l ._stack_init, r15 /* stack */
+
+ mov.l ._sh_generic_init, r0
+ jsr @r0
+ nop
+
+loop:
+ bra loop
+
+ .align 2
+
+._lowlevel_init: .long (lowlevel_init - (100b + 4))
+._reloc_dst: .long reloc_dst
+._reloc_dst_end: .long reloc_dst_end
+._bss_start: .long bss_start
+._bss_end: .long bss_end
+._gd_init: .long (_start - CFG_GBL_DATA_SIZE)
+._stack_init: .long (_start - CFG_GBL_DATA_SIZE - CFG_MALLOC_LEN - 16)
+._sh_generic_init: .long sh_generic_init
diff --git a/cpu/sh2/time.c b/cpu/sh2/time.c
new file mode 100644
index 0000000..d6eb0cb
--- /dev/null
+++ b/cpu/sh2/time.c
@@ -0,0 +1,111 @@
+/*
+ * Copyright (C) 2007,2008 Nobobuhiro Iwamatsu <iwamatsu@nigauri.org>
+ * Copyright (C) 2008 Renesas Solutions Corp.
+ *
+ * (C) Copyright 2003
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/processor.h>
+
+#define CMT_CMCSR_INIT 0x0001 /* PCLK/32 */
+#define CMT_CMCSR_CALIB 0x0000
+#define CMT_MAX_COUNTER (0xFFFFFFFF)
+#define CMT_TIMER_RESET (0xFFFF)
+
+static vu_long cmt0_timer;
+
+static void cmt_timer_start(unsigned int timer)
+{
+ writew(readw(CMSTR) | 0x01, CMSTR);
+}
+
+static void cmt_timer_stop(unsigned int timer)
+{
+ writew(readw(CMSTR) & ~0x01, CMSTR);
+}
+
+int timer_init(void)
+{
+ cmt0_timer = 0;
+ /* Divide clock by 32 */
+ readw(CMCSR_0);
+ writew(CMT_CMCSR_INIT, CMCSR_0);
+
+ /* User Device 0 only */
+ cmt_timer_stop(0);
+ set_timer(CMT_TIMER_RESET);
+ cmt_timer_start(0);
+
+ return 0;
+}
+
+unsigned long long get_ticks(void)
+{
+ return cmt0_timer;
+}
+
+static vu_long cmcnt;
+ulong get_timer(ulong base)
+{
+ ulong data = readw(CMCNT_0);
+
+ if (data >= cmcnt)
+ cmcnt = data - cmcnt;
+ else
+ cmcnt = (CMT_TIMER_RESET - cmcnt) + data;
+
+ if ((cmt0_timer + cmcnt) > CMT_MAX_COUNTER)
+ cmt0_timer = ((cmt0_timer + cmcnt) - CMT_MAX_COUNTER);
+ else
+ cmt0_timer += cmcnt;
+
+ cmcnt = data;
+ return cmt0_timer - base;
+}
+
+void set_timer(ulong t)
+{
+ writew((u16) t, CMCOR_0);
+}
+
+void reset_timer(void)
+{
+ cmt_timer_stop(0);
+ set_timer(CMT_TIMER_RESET);
+ cmt0_timer = 0;
+ cmt_timer_start(0);
+}
+
+void udelay(unsigned long usec)
+{
+ unsigned int start = get_timer(0);
+
+ while (get_timer((ulong) start) < (usec * (CFG_HZ / 1000000)))
+ continue;
+}
+
+unsigned long get_tbclk(void)
+{
+ return CFG_HZ;
+}
diff --git a/cpu/sh2/watchdog.c b/cpu/sh2/watchdog.c
new file mode 100644
index 0000000..de0254b
--- /dev/null
+++ b/cpu/sh2/watchdog.c
@@ -0,0 +1,33 @@
+/*
+ * Copyright (C) 2008 Nobuhiro Iwamatsu <iwamatsu.nobuhoro@renesas.com>
+ * Copyright (C) 2008 Renesas Solutions Corp.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+
+int watchdog_init(void)
+{
+ return 0;
+}
+
+void reset_cpu(unsigned long ignored)
+{
+ while (1)
+ ;
+}
generated by cgit v1.1 at 2024-12-19 13:03:18 +0000