diff options
Diffstat (limited to 'cpu')
| -rw-r--r-- | cpu/i386/sc520.c | 18 | ||||
| -rw-r--r-- | cpu/i386/sc520_asm.S | 54 |
2 files changed, 65 insertions, 7 deletions
diff --git a/cpu/i386/sc520.c b/cpu/i386/sc520.c index c83f0bb..1c4370b 100644 --- a/cpu/i386/sc520.c +++ b/cpu/i386/sc520.c @@ -31,7 +31,9 @@ #include <common.h> #include <config.h> #include <pci.h> +#ifdef CONFIG_SC520_SSI #include <ssi.h> +#endif #include <asm/io.h> #include <asm/pci.h> #include <asm/ic/sc520.h> @@ -143,7 +145,15 @@ unsigned long init_sc520_dram(void) u32 dram_present=0; u32 dram_ctrl; - +#ifdef CFG_SDRAM_DRCTMCTL + /* these memory control registers are set up in the assember part, + * in sc520_asm.S, during 'mem_init'. If we muck with them here, + * after we are running a stack in RAM, we have troubles. Besides, + * these refresh and delay values are better ? simply specified + * outright in the include/configs/{cfg} file since the HW designer + * simply dictates it. + */ +#else int val; int cas_precharge_delay = CFG_SDRAM_PRECHARGE_DELAY; @@ -162,6 +172,7 @@ unsigned long init_sc520_dram(void) } else { val = 3; /* 62.4us */ } + write_mmcr_byte(SC520_DRCCTL, (read_mmcr_byte(SC520_DRCCTL) & 0xcf) | (val<<4)); val = read_mmcr_byte(SC520_DRCTMCTL); @@ -181,13 +192,12 @@ unsigned long init_sc520_dram(void) val |= 1; } write_mmcr_byte(SC520_DRCTMCTL, val); - +#endif /* We read-back the configuration of the dram * controller that the assembly code wrote */ dram_ctrl = read_mmcr_long(SC520_DRCBENDADR); - bd->bi_dram[0].start = 0; if (dram_ctrl & 0x80) { /* bank 0 enabled */ @@ -274,7 +284,7 @@ int pci_sc520_set_irq(int pci_pin, int irq) { int i; -# if 0 +# if 1 printf("set_irq(): map INT%c to IRQ%d\n", pci_pin + 'A', irq); #endif if (irq < 0 || irq > 15) { diff --git a/cpu/i386/sc520_asm.S b/cpu/i386/sc520_asm.S index 80464fa..e1fa37a 100644 --- a/cpu/i386/sc520_asm.S +++ b/cpu/i386/sc520_asm.S @@ -113,6 +113,7 @@ .equ DRCCFG, 0x0fffef014 /* DRAM bank configuration register */ .equ DRCBENDADR, 0x0fffef018 /* DRAM bank ending address register */ .equ ECCCTL, 0x0fffef020 /* DRAM ECC control register */ +.equ ECCINT, 0x0fffefd18 /* DRAM ECC nmi-INT mapping */ .equ DBCTL, 0x0fffef040 /* DRAM buffer control register */ .equ CACHELINESZ, 0x00000010 /* size of our cache line (read buffer) */ @@ -459,6 +460,12 @@ emptybank: incl %edi loop cleanuplp +#if defined CFG_SDRAM_DRCTMCTL + /* just have your hardware desinger _GIVE_ you what you need here! */ + movl $DRCTMCTL, %edi + movb $CFG_SDRAM_DRCTMCTL,%al + movb (%edi), %al +#else #if defined(CFG_SDRAM_CAS_LATENCY_2T) || defined(CFG_SDRAM_CAS_LATENCY_3T) /* set the CAS latency now since it is hard to do * when we run from the RAM */ @@ -470,7 +477,8 @@ emptybank: #ifdef CFG_SDRAM_CAS_LATENCY_3T orb $0x10, %al #endif - movb %al, (%edi) + movb %al, (%edi) +#endif #endif movl $DRCCTL, %edi /* DRAM Control register */ movb $0x3,%al /* Load mode register cmd */ @@ -528,9 +536,49 @@ bank0: movl (%edi), %eax shll $22, %eax movl %eax, %ebx -done: movl %ebx, %eax +done: + movl %ebx, %eax + +#if CFG_SDRAM_ECC_ENABLE + /* A nominal memory test: just a byte at each address line */ + movl %eax, %ecx + shrl $0x1, %ecx + movl $0x1, %edi +memtest0: + movb $0xa5, (%edi) + cmpb $0xa5, (%edi) + jne out + shrl $1, %ecx + andl %ecx,%ecx + jz set_ecc + shll $1, %edi + jmp memtest0 + +set_ecc: + /* clear all ram with a memset */ + movl %eax, %ecx + xorl %esi, %esi + xorl %edi, %edi + xorl %eax, %eax + shrl $2, %ecx + cld + rep stosl + /* enable read, write buffers */ + movb $0x11, %al + movl $DBCTL, %edi + movb %al, (%edi) + /* enable NMI mapping for ECC */ + movl $ECCINT, %edi + mov $0x10, %al + movb %al, (%edi) + /* Turn on ECC */ + movl $ECCCTL, %edi + mov $0x05, %al + movb %al, (%edi) +#endif +out: + movl %ebx, %eax jmp *%ebp - #endif /* CONFIG_SC520 */ |