diff options
Diffstat (limited to 'cpu/ppc4xx/spd_sdram.c')
| -rw-r--r-- | cpu/ppc4xx/spd_sdram.c | 2343 |
1 files changed, 1145 insertions, 1198 deletions
diff --git a/cpu/ppc4xx/spd_sdram.c b/cpu/ppc4xx/spd_sdram.c index 794a72c..520107a 100644 --- a/cpu/ppc4xx/spd_sdram.c +++ b/cpu/ppc4xx/spd_sdram.c @@ -16,6 +16,9 @@ * Jun Gu, Artesyn Technology, jung@artesyncp.com * Support for IBM 440 based on OpenBIOS draminit.c from IBM. * + * (C) Copyright 2005 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * * See file CREDITS for list of people who contributed to this * project. * @@ -53,7 +56,9 @@ #define CFG_I2C_SLAVE 0xFE #endif -#ifndef CONFIG_440 /* for 405 WALNUT board */ +#define ONE_BILLION 1000000000 + +#ifndef CONFIG_440 /* for 405 WALNUT/SYCAMORE/BUBINGA boards */ #define SDRAM0_CFG_DCE 0x80000000 #define SDRAM0_CFG_SRE 0x40000000 @@ -111,7 +116,7 @@ int spd_read(uint addr); long int spd_sdram(int(read_spd)(uint addr)) { - int bus_period,tmp,row,col; + int tmp,row,col; int total_size,bank_size,bank_code; int ecc_on; int mode; @@ -141,226 +146,189 @@ long int spd_sdram(int(read_spd)(uint addr)) int t_rc; int min_cas; - if(read_spd == 0){ - read_spd=spd_read; - /* - * Make sure I2C controller is initialized - * before continuing. - */ - i2c_init(CFG_I2C_SPEED, CFG_I2C_SLAVE); - } - + PPC405_SYS_INFO sys_info; + unsigned long bus_period_x_10; /* - * Calculate the bus period, we do it this - * way to minimize stack utilization. + * get the board info */ -#ifndef CONFIG_405EP - tmp = (mfdcr(pllmd) >> (31-6)) & 0xf; /* get FBDV bits */ - tmp = CONFIG_SYS_CLK_FREQ * tmp; /* get plb freq */ -#else - { - unsigned long freqCPU; - unsigned long pllmr0; - unsigned long pllmr1; - unsigned long pllFbkDiv; - unsigned long pllPlbDiv; - unsigned long pllmr0_ccdv; - - /* - * Read PLL Mode registers - */ - pllmr0 = mfdcr (cpc0_pllmr0); - pllmr1 = mfdcr (cpc0_pllmr1); - - pllFbkDiv = ((pllmr1 & PLLMR1_FBMUL_MASK) >> 20); - if (pllFbkDiv == 0) { - pllFbkDiv = 16; - } - pllPlbDiv = ((pllmr0 & PLLMR0_CPU_TO_PLB_MASK) >> 16) + 1; - - /* - * Determine CPU clock frequency - */ - pllmr0_ccdv = ((pllmr0 & PLLMR0_CPU_DIV_MASK) >> 20) + 1; - if (pllmr1 & PLLMR1_SSCS_MASK) { - freqCPU = (CONFIG_SYS_CLK_FREQ * pllFbkDiv) / pllmr0_ccdv; - } else { - freqCPU = CONFIG_SYS_CLK_FREQ / pllmr0_ccdv; - } + get_sys_info(&sys_info); + bus_period_x_10 = ONE_BILLION / (sys_info.freqPLB / 10); + if (read_spd == 0){ + read_spd=spd_read; /* - * Determine PLB clock frequency + * Make sure I2C controller is initialized + * before continuing. */ - tmp = freqCPU / pllPlbDiv; + i2c_init(CFG_I2C_SPEED, CFG_I2C_SLAVE); } -#endif - bus_period = sdram_HZ_to_ns(tmp); /* get sdram speed */ /* Make shure we are using SDRAM */ - if (read_spd(2) != 0x04){ - SPD_ERR("SDRAM - non SDRAM memory module found\n"); - } - -/*------------------------------------------------------------------ - configure memory timing register + if (read_spd(2) != 0x04) { + SPD_ERR("SDRAM - non SDRAM memory module found\n"); + } - data from DIMM: - 27 IN Row Precharge Time ( t RP) - 29 MIN RAS to CAS Delay ( t RCD) - 127 Component and Clock Detail ,clk0-clk3, junction temp, CAS - -------------------------------------------------------------------*/ + /* ------------------------------------------------------------------ + * configure memory timing register + * + * data from DIMM: + * 27 IN Row Precharge Time ( t RP) + * 29 MIN RAS to CAS Delay ( t RCD) + * 127 Component and Clock Detail ,clk0-clk3, junction temp, CAS + * -------------------------------------------------------------------*/ - /* - * first figure out which cas latency mode to use - * use the min supported mode - */ + /* + * first figure out which cas latency mode to use + * use the min supported mode + */ tmp = read_spd(127) & 0x6; - if(tmp == 0x02){ /* only cas = 2 supported */ - min_cas = 2; + if (tmp == 0x02){ /* only cas = 2 supported */ + min_cas = 2; /* t_ck = read_spd(9); */ /* t_ac = read_spd(10); */ - } - else if (tmp == 0x04){ /* only cas = 3 supported */ - min_cas = 3; + } else if (tmp == 0x04) { /* only cas = 3 supported */ + min_cas = 3; /* t_ck = read_spd(9); */ /* t_ac = read_spd(10); */ - } - else if (tmp == 0x06){ /* 2,3 supported, so use 2 */ - min_cas = 2; + } else if (tmp == 0x06) { /* 2,3 supported, so use 2 */ + min_cas = 2; /* t_ck = read_spd(23); */ /* t_ac = read_spd(24); */ - } - else { - SPD_ERR("SDRAM - unsupported CAS latency \n"); + } else { + SPD_ERR("SDRAM - unsupported CAS latency \n"); } - /* get some timing values, t_rp,t_rcd,t_ras,t_rc - */ - t_rp = read_spd(27); - t_rcd = read_spd(29); - t_ras = read_spd(30); - t_rc = t_ras + t_rp; - - /* The following timing calcs subtract 1 before deviding. - * this has effect of using ceiling instead of floor rounding, - * and also subtracting 1 to convert number to reg value - */ - /* set up CASL */ - sdram0_tr = (min_cas - 1) << SDRAM0_TR_CASL_SHIFT; - /* set up PTA */ - sdram0_tr |= (((t_rp - 1)/bus_period) & 0x3) << SDRAM0_TR_PTA_SHIFT; - /* set up CTP */ - tmp = ((t_rc - t_rcd - t_rp -1) / bus_period) & 0x3; - if(tmp<1) tmp=1; - sdram0_tr |= tmp << SDRAM0_TR_CTP_SHIFT; - /* set LDF = 2 cycles, reg value = 1 */ - sdram0_tr |= 1 << SDRAM0_TR_LDF_SHIFT; - /* set RFTA = t_rfc/bus_period, use t_rfc = t_rc */ - tmp = ( (t_rc - 1) / bus_period)-3; - if(tmp<0)tmp=0; - if(tmp>6)tmp=6; + /* get some timing values, t_rp,t_rcd,t_ras,t_rc + */ + t_rp = read_spd(27); + t_rcd = read_spd(29); + t_ras = read_spd(30); + t_rc = t_ras + t_rp; + + /* The following timing calcs subtract 1 before deviding. + * this has effect of using ceiling instead of floor rounding, + * and also subtracting 1 to convert number to reg value + */ + /* set up CASL */ + sdram0_tr = (min_cas - 1) << SDRAM0_TR_CASL_SHIFT; + /* set up PTA */ + sdram0_tr |= ((((t_rp - 1) * 10)/bus_period_x_10) & 0x3) << SDRAM0_TR_PTA_SHIFT; + /* set up CTP */ + tmp = (((t_rc - t_rcd - t_rp -1) * 10) / bus_period_x_10) & 0x3; + if (tmp < 1) + tmp = 1; + sdram0_tr |= tmp << SDRAM0_TR_CTP_SHIFT; + /* set LDF = 2 cycles, reg value = 1 */ + sdram0_tr |= 1 << SDRAM0_TR_LDF_SHIFT; + /* set RFTA = t_rfc/bus_period, use t_rfc = t_rc */ + tmp = (((t_rc - 1) * 10) / bus_period_x_10) - 3; + if (tmp < 0) + tmp = 0; + if (tmp > 6) + tmp = 6; sdram0_tr |= tmp << SDRAM0_TR_RFTA_SHIFT; - /* set RCD = t_rcd/bus_period*/ - sdram0_tr |= (((t_rcd - 1) / bus_period) &0x3) << SDRAM0_TR_RCD_SHIFT ; + /* set RCD = t_rcd/bus_period*/ + sdram0_tr |= ((((t_rcd - 1) * 10) / bus_period_x_10) &0x3) << SDRAM0_TR_RCD_SHIFT ; -/*------------------------------------------------------------------ - configure RTR register - -------------------------------------------------------------------*/ - row = read_spd(3); - col = read_spd(4); - tmp = read_spd(12) & 0x7f ; /* refresh type less self refresh bit */ - switch(tmp){ + /*------------------------------------------------------------------ + * configure RTR register + * -------------------------------------------------------------------*/ + row = read_spd(3); + col = read_spd(4); + tmp = read_spd(12) & 0x7f ; /* refresh type less self refresh bit */ + switch (tmp) { case 0x00: - tmp=15625; - break; + tmp = 15625; + break; case 0x01: - tmp=15625/4; - break; + tmp = 15625 / 4; + break; case 0x02: - tmp=15625/2; - break; + tmp = 15625 / 2; + break; case 0x03: - tmp=15625*2; - break; + tmp = 15625 * 2; + break; case 0x04: - tmp=15625*4; - break; + tmp = 15625 * 4; + break; case 0x05: - tmp=15625*8; - break; + tmp = 15625 * 8; + break; default: - SPD_ERR("SDRAM - Bad refresh period \n"); + SPD_ERR("SDRAM - Bad refresh period \n"); } /* convert from nsec to bus cycles */ - tmp = tmp/bus_period; - sdram0_rtr = (tmp & 0x3ff8)<< SDRAM0_RTR_SHIFT; + tmp = (tmp * 10) / bus_period_x_10; + sdram0_rtr = (tmp & 0x3ff8) << SDRAM0_RTR_SHIFT; -/*------------------------------------------------------------------ - determine the number of banks used - -------------------------------------------------------------------*/ + /*------------------------------------------------------------------ + * determine the number of banks used + * -------------------------------------------------------------------*/ /* byte 7:6 is module data width */ - if(read_spd(7) != 0) - SPD_ERR("SDRAM - unsupported module width\n"); + if (read_spd(7) != 0) + SPD_ERR("SDRAM - unsupported module width\n"); tmp = read_spd(6); if (tmp < 32) - SPD_ERR("SDRAM - unsupported module width\n"); + SPD_ERR("SDRAM - unsupported module width\n"); else if (tmp < 64) - bank_cnt=1; /* one bank per sdram side */ + bank_cnt = 1; /* one bank per sdram side */ else if (tmp < 73) - bank_cnt=2; /* need two banks per side */ + bank_cnt = 2; /* need two banks per side */ else if (tmp < 161) - bank_cnt=4; /* need four banks per side */ + bank_cnt = 4; /* need four banks per side */ else - SPD_ERR("SDRAM - unsupported module width\n"); + SPD_ERR("SDRAM - unsupported module width\n"); /* byte 5 is the module row count (refered to as dimm "sides") */ tmp = read_spd(5); - if(tmp==1); - else if(tmp==2) bank_cnt *=2; - else if(tmp==4) bank_cnt *=4; - else bank_cnt = 8; /* 8 is an error code */ + if (tmp == 1) + ; + else if (tmp==2) + bank_cnt *= 2; + else if (tmp==4) + bank_cnt *= 4; + else + bank_cnt = 8; /* 8 is an error code */ - if(bank_cnt > 4) /* we only have 4 banks to work with */ - SPD_ERR("SDRAM - unsupported module rows for this width\n"); + if (bank_cnt > 4) /* we only have 4 banks to work with */ + SPD_ERR("SDRAM - unsupported module rows for this width\n"); /* now check for ECC ability of module. We only support ECC * on 32 bit wide devices with 8 bit ECC. */ - if ( (read_spd(11)==2) && (read_spd(6)==40) && (read_spd(14)==8) ){ - sdram0_ecccfg=0xf<<SDRAM0_ECCCFG_SHIFT; - ecc_on = 1; - } - else{ - sdram0_ecccfg=0; - ecc_on = 0; + if ((read_spd(11)==2) && (read_spd(6)==40) && (read_spd(14)==8)) { + sdram0_ecccfg = 0xf << SDRAM0_ECCCFG_SHIFT; + ecc_on = 1; + } else { + sdram0_ecccfg = 0; + ecc_on = 0; } -/*------------------------------------------------------------------ - calculate total size - -------------------------------------------------------------------*/ + /*------------------------------------------------------------------ + * calculate total size + * -------------------------------------------------------------------*/ /* calculate total size and do sanity check */ tmp = read_spd(31); - total_size=1<<22; /* total_size = 4MB */ + total_size = 1 << 22; /* total_size = 4MB */ /* now multiply 4M by the smallest device row density */ /* note that we don't support asymetric rows */ - while (((tmp & 0x0001) == 0) && (tmp != 0)){ - total_size= total_size<<1; - tmp = tmp>>1; - } + while (((tmp & 0x0001) == 0) && (tmp != 0)) { + total_size = total_size << 1; + tmp = tmp >> 1; + } total_size *= read_spd(5); /* mult by module rows (dimm sides) */ -/*------------------------------------------------------------------ - map rows * cols * banks to a mode - -------------------------------------------------------------------*/ + /*------------------------------------------------------------------ + * map rows * cols * banks to a mode + * -------------------------------------------------------------------*/ - switch( row ) - { + switch (row) { case 11: - switch ( col ) - { + switch (col) { case 8: mode=4; /* mode 5 */ break; @@ -369,12 +337,11 @@ long int spd_sdram(int(read_spd)(uint addr)) mode=0; /* mode 1 */ break; default: - SPD_ERR("SDRAM - unsupported mode\n"); + SPD_ERR("SDRAM - unsupported mode\n"); } break; case 12: - switch ( col ) - { + switch (col) { case 8: mode=3; /* mode 4 */ break; @@ -383,37 +350,36 @@ long int spd_sdram(int(read_spd)(uint addr)) mode=1; /* mode 2 */ break; default: - SPD_ERR("SDRAM - unsupported mode\n"); + SPD_ERR("SDRAM - unsupported mode\n"); } break; case 13: - switch ( col ) - { + switch (col) { case 8: mode=5; /* mode 6 */ break; case 9: case 10: - if (read_spd(17) ==2 ) - mode=6; /* mode 7 */ + if (read_spd(17) == 2) + mode = 6; /* mode 7 */ else - mode=2; /* mode 3 */ + mode = 2; /* mode 3 */ break; case 11: - mode=2; /* mode 3 */ + mode = 2; /* mode 3 */ break; default: - SPD_ERR("SDRAM - unsupported mode\n"); + SPD_ERR("SDRAM - unsupported mode\n"); } break; default: - SPD_ERR("SDRAM - unsupported mode\n"); + SPD_ERR("SDRAM - unsupported mode\n"); } -/*------------------------------------------------------------------ - using the calculated values, compute the bank - config register values. - -------------------------------------------------------------------*/ + /*------------------------------------------------------------------ + * using the calculated values, compute the bank + * config register values. + * -------------------------------------------------------------------*/ sdram0_b1cr = 0; sdram0_b2cr = 0; sdram0_b3cr = 0; @@ -421,44 +387,46 @@ long int spd_sdram(int(read_spd)(uint addr)) /* compute the size of each bank */ bank_size = total_size / bank_cnt; /* convert bank size to bank size code for ppc4xx - by takeing log2(bank_size) - 22 */ - tmp=bank_size; /* start with tmp = bank_size */ - bank_code=0; /* and bank_code = 0 */ - while (tmp>1){ /* this takes log2 of tmp */ + by takeing log2(bank_size) - 22 */ + tmp = bank_size; /* start with tmp = bank_size */ + bank_code = 0; /* and bank_code = 0 */ + while (tmp > 1) { /* this takes log2 of tmp */ bank_code++; /* and stores result in bank_code */ - tmp=tmp>>1; - } /* bank_code is now log2(bank_size) */ - bank_code-=22; /* subtract 22 to get the code */ + tmp = tmp >> 1; + } /* bank_code is now log2(bank_size) */ + bank_code -= 22; /* subtract 22 to get the code */ tmp = SDRAM0_BXCR_SZ(bank_code) | SDRAM0_BXCR_AM(mode) | 1; - sdram0_b0cr = (bank_size) * 0 | tmp; + sdram0_b0cr = (bank_size * 0) | tmp; #ifndef CONFIG_405EP /* not on PPC405EP */ - if(bank_cnt>1) sdram0_b2cr = (bank_size) * 1 | tmp; - if(bank_cnt>2) sdram0_b1cr = (bank_size) * 2 | tmp; - if(bank_cnt>3) sdram0_b3cr = (bank_size) * 3 | tmp; + if (bank_cnt > 1) + sdram0_b2cr = (bank_size * 1) | tmp; + if (bank_cnt > 2) + sdram0_b1cr = (bank_size * 2) | tmp; + if (bank_cnt > 3) + sdram0_b3cr = (bank_size * 3) | tmp; #else /* PPC405EP chip only supports two SDRAM banks */ - if(bank_cnt>1) sdram0_b1cr = (bank_size) * 1 | tmp; - if(bank_cnt>2) total_size -= (bank_size) * (bank_cnt - 2); + if (bank_cnt > 1) + sdram0_b1cr = (bank_size * 1) | tmp; + if (bank_cnt > 2) + total_size = 2 * bank_size; #endif - /* * enable sdram controller DCE=1 * enable burst read prefetch to 32 bytes BRPF=2 * leave other functions off */ -/*------------------------------------------------------------------ - now that we've done our calculations, we are ready to - program all the registers. - -------------------------------------------------------------------*/ - + /*------------------------------------------------------------------ + * now that we've done our calculations, we are ready to + * program all the registers. + * -------------------------------------------------------------------*/ #define mtsdram0(reg, data) mtdcr(memcfga,reg);mtdcr(memcfgd,data) /* disable memcontroller so updates work */ - sdram0_cfg = 0; - mtsdram0( mem_mcopt1, sdram0_cfg ); + mtsdram0( mem_mcopt1, 0 ); #ifndef CONFIG_405EP /* not on PPC405EP */ mtsdram0( mem_besra , sdram0_besr0 ); @@ -479,15 +447,10 @@ long int spd_sdram(int(read_spd)(uint addr)) /* SDRAM have a power on delay, 500 micro should do */ udelay(500); sdram0_cfg = SDRAM0_CFG_DCE | SDRAM0_CFG_BRPF(1) | SDRAM0_CFG_ECCDD | SDRAM0_CFG_EMDULR; - if(ecc_on) sdram0_cfg |= SDRAM0_CFG_MEMCHK; - mtsdram0( mem_mcopt1, sdram0_cfg ); - + if (ecc_on) + sdram0_cfg |= SDRAM0_CFG_MEMCHK; + mtsdram0(mem_mcopt1, sdram0_cfg); - /* kernel 2.4.2 from mvista has a bug with memory over 128MB */ -#ifdef MVISTA_MEM_BUG - if (total_size > 128*1024*1024 ) - total_size=128*1024*1024; -#endif return (total_size); } @@ -504,8 +467,8 @@ int spd_read(uint addr) #else /* CONFIG_440 */ /*----------------------------------------------------------------------------- -| Memory Controller Options 0 -+-----------------------------------------------------------------------------*/ + | Memory Controller Options 0 + +-----------------------------------------------------------------------------*/ #define SDRAM_CFG0_DCEN 0x80000000 /* SDRAM Controller Enable */ #define SDRAM_CFG0_MCHK_MASK 0x30000000 /* Memory data errchecking mask */ #define SDRAM_CFG0_MCHK_NON 0x00000000 /* No ECC generation */ @@ -520,39 +483,39 @@ int spd_read(uint addr) #define SDRAM_CFG0_PDP 0x00200000 /* Page deallocation policy */ /*----------------------------------------------------------------------------- -| Memory Controller Options 1 -+-----------------------------------------------------------------------------*/ + | Memory Controller Options 1 + +-----------------------------------------------------------------------------*/ #define SDRAM_CFG1_SRE 0x80000000 /* Self-Refresh Entry */ #define SDRAM_CFG1_PMEN 0x40000000 /* Power Management Enable */ /*-----------------------------------------------------------------------------+ -| SDRAM DEVPOT Options -+-----------------------------------------------------------------------------*/ + | SDRAM DEVPOT Options + +-----------------------------------------------------------------------------*/ #define SDRAM_DEVOPT_DLL 0x80000000 #define SDRAM_DEVOPT_DS 0x40000000 /*-----------------------------------------------------------------------------+ -| SDRAM MCSTS Options -+-----------------------------------------------------------------------------*/ + | SDRAM MCSTS Options + +-----------------------------------------------------------------------------*/ #define SDRAM_MCSTS_MRSC 0x80000000 #define SDRAM_MCSTS_SRMS 0x40000000 #define SDRAM_MCSTS_CIS 0x20000000 /*----------------------------------------------------------------------------- -| SDRAM Refresh Timer Register -+-----------------------------------------------------------------------------*/ + | SDRAM Refresh Timer Register + +-----------------------------------------------------------------------------*/ #define SDRAM_RTR_RINT_MASK 0xFFFF0000 #define SDRAM_RTR_RINT_ENCODE(n) (((n) << 16) & SDRAM_RTR_RINT_MASK) #define sdram_HZ_to_ns(hertz) (1000000000/(hertz)) /*-----------------------------------------------------------------------------+ -| SDRAM UABus Base Address Reg -+-----------------------------------------------------------------------------*/ + | SDRAM UABus Base Address Reg + +-----------------------------------------------------------------------------*/ #define SDRAM_UABBA_UBBA_MASK 0x0000000F /*-----------------------------------------------------------------------------+ -| Memory Bank 0-7 configuration -+-----------------------------------------------------------------------------*/ + | Memory Bank 0-7 configuration + +-----------------------------------------------------------------------------*/ #define SDRAM_BXCR_SDBA_MASK 0xff800000 /* Base address */ #define SDRAM_BXCR_SDSZ_MASK 0x000e0000 /* Size */ #define SDRAM_BXCR_SDSZ_8 0x00020000 /* 8M */ @@ -570,8 +533,8 @@ int spd_read(uint addr) #define SDRAM_BXCR_SDBE 0x00000001 /* Memory Bank Enable */ /*-----------------------------------------------------------------------------+ -| SDRAM TR0 Options -+-----------------------------------------------------------------------------*/ + | SDRAM TR0 Options + +-----------------------------------------------------------------------------*/ #define SDRAM_TR0_SDWR_MASK 0x80000000 #define SDRAM_TR0_SDWR_2_CLK 0x00000000 #define SDRAM_TR0_SDWR_3_CLK 0x80000000 @@ -609,8 +572,8 @@ int spd_read(uint addr) #define SDRAM_TR0_SDRD_4_CLK 0x00000003 /*-----------------------------------------------------------------------------+ -| SDRAM TR1 Options -+-----------------------------------------------------------------------------*/ + | SDRAM TR1 Options + +-----------------------------------------------------------------------------*/ #define SDRAM_TR1_RDSS_MASK 0xC0000000 #define SDRAM_TR1_RDSS_TR0 0x00000000 #define SDRAM_TR1_RDSS_TR1 0x40000000 @@ -630,8 +593,8 @@ int spd_read(uint addr) #define SDRAM_TR1_RDCT_MAX 0x000001FF /*-----------------------------------------------------------------------------+ -| SDRAM WDDCTR Options -+-----------------------------------------------------------------------------*/ + | SDRAM WDDCTR Options + +-----------------------------------------------------------------------------*/ #define SDRAM_WDDCTR_WRCP_MASK 0xC0000000 #define SDRAM_WDDCTR_WRCP_0DEG 0x00000000 #define SDRAM_WDDCTR_WRCP_90DEG 0x40000000 @@ -639,8 +602,8 @@ int spd_read(uint addr) #define SDRAM_WDDCTR_DCD_MASK 0x000001FF /*-----------------------------------------------------------------------------+ -| SDRAM CLKTR Options -+-----------------------------------------------------------------------------*/ + | SDRAM CLKTR Options + +-----------------------------------------------------------------------------*/ #define SDRAM_CLKTR_CLKP_MASK 0xC0000000 #define SDRAM_CLKTR_CLKP_0DEG 0x00000000 #define SDRAM_CLKTR_CLKP_90DEG 0x40000000 @@ -648,18 +611,17 @@ int spd_read(uint addr) #define SDRAM_CLKTR_DCDT_MASK 0x000001FF /*-----------------------------------------------------------------------------+ -| SDRAM DLYCAL Options -+-----------------------------------------------------------------------------*/ + | SDRAM DLYCAL Options + +-----------------------------------------------------------------------------*/ #define SDRAM_DLYCAL_DLCV_MASK 0x000003FC #define SDRAM_DLYCAL_DLCV_ENCODE(x) (((x)<<2) & SDRAM_DLYCAL_DLCV_MASK) #define SDRAM_DLYCAL_DLCV_DECODE(x) (((x) & SDRAM_DLYCAL_DLCV_MASK)>>2) /*-----------------------------------------------------------------------------+ -| General Definition -+-----------------------------------------------------------------------------*/ + | General Definition + +-----------------------------------------------------------------------------*/ #define DEFAULT_SPD_ADDR1 0x53 #define DEFAULT_SPD_ADDR2 0x52 -#define ONE_BILLION 1000000000 #define MAXBANKS 4 /* at most 4 dimm banks */ #define MAX_SPD_BYTES 256 #define NUMHALFCYCLES 4 @@ -670,22 +632,22 @@ int spd_read(uint addr) #define FALSE 0 const unsigned long test[NUMMEMTESTS][NUMMEMWORDS] = { - {0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000, - 0xFFFFFFFF, 0xFFFFFFFF}, - {0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF, - 0x00000000, 0x00000000}, - {0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA, - 0x55555555, 0x55555555}, - {0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555, - 0xAAAAAAAA, 0xAAAAAAAA}, - {0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5, - 0x5A5A5A5A, 0x5A5A5A5A}, - {0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A, - 0xA5A5A5A5, 0xA5A5A5A5}, - {0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55, - 0x55AA55AA, 0x55AA55AA}, - {0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA, - 0xAA55AA55, 0xAA55AA55} + {0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000, + 0xFFFFFFFF, 0xFFFFFFFF}, + {0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF, + 0x00000000, 0x00000000}, + {0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA, + 0x55555555, 0x55555555}, + {0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555, + 0xAAAAAAAA, 0xAAAAAAAA}, + {0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5, + 0x5A5A5A5A, 0x5A5A5A5A}, + {0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A, + 0xA5A5A5A5, 0xA5A5A5A5}, + {0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55, + 0x55AA55AA, 0x55AA55AA}, + {0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA, + 0xAA55AA55, 0xAA55AA55} }; @@ -696,14 +658,14 @@ void get_spd_info(unsigned long* dimm_populated, unsigned long num_dimm_banks); void check_mem_type - (unsigned long* dimm_populated, - unsigned char* iic0_dimm_addr, - unsigned long num_dimm_banks); +(unsigned long* dimm_populated, + unsigned char* iic0_dimm_addr, + unsigned long num_dimm_banks); void check_volt_type - (unsigned long* dimm_populated, - unsigned char* iic0_dimm_addr, - unsigned long num_dimm_banks); +(unsigned long* dimm_populated, + unsigned char* iic0_dimm_addr, + unsigned long num_dimm_banks); void program_cfg0(unsigned long* dimm_populated, unsigned char* iic0_dimm_addr, @@ -741,14 +703,14 @@ long program_bxcr(unsigned long* dimm_populated, */ long int spd_sdram(void) { - unsigned char iic0_dimm_addr[] = SPD_EEPROM_ADDRESS; - unsigned long dimm_populated[sizeof(iic0_dimm_addr)]; - unsigned long total_size; - unsigned long cfg0; - unsigned long mcsts; - unsigned long num_dimm_banks; /* on board dimm banks */ + unsigned char iic0_dimm_addr[] = SPD_EEPROM_ADDRESS; + unsigned long dimm_populated[sizeof(iic0_dimm_addr)]; + unsigned long total_size; + unsigned long cfg0; + unsigned long mcsts; + unsigned long num_dimm_banks; /* on board dimm banks */ - num_dimm_banks = sizeof(iic0_dimm_addr); + num_dimm_banks = sizeof(iic0_dimm_addr); /* * Make sure I2C controller is initialized @@ -756,90 +718,90 @@ long int spd_sdram(void) { */ i2c_init(CFG_I2C_SPEED, CFG_I2C_SLAVE); - /* - * Read the SPD information using I2C interface. Check to see if the - * DIMM slots are populated. - */ - get_spd_info(dimm_populated, iic0_dimm_addr, num_dimm_banks); + /* + * Read the SPD information using I2C interface. Check to see if the + * DIMM slots are populated. + */ + get_spd_info(dimm_populated, iic0_dimm_addr, num_dimm_banks); - /* - * Check the memory type for the dimms plugged. - */ - check_mem_type(dimm_populated, iic0_dimm_addr, num_dimm_banks); + /* + * Check the memory type for the dimms plugged. + */ + check_mem_type(dimm_populated, iic0_dimm_addr, num_dimm_banks); - /* - * Check the voltage type for the dimms plugged. - */ - check_volt_type(dimm_populated, iic0_dimm_addr, num_dimm_banks); + /* + * Check the voltage type for the dimms plugged. + */ + check_volt_type(dimm_populated, iic0_dimm_addr, num_dimm_banks); #if defined(CONFIG_440_GX) - /* - * Soft-reset SDRAM controller. - */ - mtsdr(sdr_srst, SDR0_SRST_DMC); - mtsdr(sdr_srst, 0x00000000); + /* + * Soft-reset SDRAM controller. + */ + mtsdr(sdr_srst, SDR0_SRST_DMC); + mtsdr(sdr_srst, 0x00000000); #endif - /* - * program 440GP SDRAM controller options (SDRAM0_CFG0) - */ - program_cfg0(dimm_populated, iic0_dimm_addr, num_dimm_banks); - - /* - * program 440GP SDRAM controller options (SDRAM0_CFG1) - */ - program_cfg1(dimm_populated, iic0_dimm_addr, num_dimm_banks); - - /* - * program SDRAM refresh register (SDRAM0_RTR) - */ - program_rtr(dimm_populated, iic0_dimm_addr, num_dimm_banks); - - /* - * program SDRAM Timing Register 0 (SDRAM0_TR0) - */ - program_tr0(dimm_populated, iic0_dimm_addr, num_dimm_banks); - - /* - * program the BxCR registers to find out total sdram installed - */ - total_size = program_bxcr(dimm_populated, iic0_dimm_addr, - num_dimm_banks); - - /* - * program SDRAM Clock Timing Register (SDRAM0_CLKTR) - */ - mtsdram(mem_clktr, 0x40000000); - - /* - * delay to ensure 200 usec has elapsed - */ - udelay(400); - - /* - * enable the memory controller - */ - mfsdram(mem_cfg0, cfg0); - mtsdram(mem_cfg0, cfg0 | SDRAM_CFG0_DCEN); - - /* - * wait for SDRAM_CFG0_DC_EN to complete - */ - while(1) { - mfsdram(mem_mcsts, mcsts); - if ((mcsts & SDRAM_MCSTS_MRSC) != 0) { - break; + /* + * program 440GP SDRAM controller options (SDRAM0_CFG0) + */ + program_cfg0(dimm_populated, iic0_dimm_addr, num_dimm_banks); + + /* + * program 440GP SDRAM controller options (SDRAM0_CFG1) + */ + program_cfg1(dimm_populated, iic0_dimm_addr, num_dimm_banks); + + /* + * program SDRAM refresh register (SDRAM0_RTR) + */ + program_rtr(dimm_populated, iic0_dimm_addr, num_dimm_banks); + + /* + * program SDRAM Timing Register 0 (SDRAM0_TR0) + */ + program_tr0(dimm_populated, iic0_dimm_addr, num_dimm_banks); + + /* + * program the BxCR registers to find out total sdram installed + */ + total_size = program_bxcr(dimm_populated, iic0_dimm_addr, + num_dimm_banks); + + /* + * program SDRAM Clock Timing Register (SDRAM0_CLKTR) + */ + mtsdram(mem_clktr, 0x40000000); + + /* + * delay to ensure 200 usec has elapsed + */ + udelay(400); + + /* + * enable the memory controller + */ + mfsdram(mem_cfg0, cfg0); + mtsdram(mem_cfg0, cfg0 | SDRAM_CFG0_DCEN); + + /* + * wait for SDRAM_CFG0_DC_EN to complete + */ + while (1) { + mfsdram(mem_mcsts, mcsts); + if ((mcsts & SDRAM_MCSTS_MRSC) != 0) { + break; + } } - } - /* - * program SDRAM Timing Register 1, adding some delays - */ - program_tr1(); + /* + * program SDRAM Timing Register 1, adding some delays + */ + program_tr1(); - /* - * if ECC is enabled, initialize parity bits - */ + /* + * if ECC is enabled, initialize parity bits + */ return total_size; } @@ -847,76 +809,78 @@ long int spd_sdram(void) { unsigned char spd_read(uchar chip, uint addr) { unsigned char data[2]; - if (i2c_read(chip, addr, 1, data, 1) == 0) - return data[0]; - else - return 0; + if (i2c_probe(chip) == 0) { + if (i2c_read(chip, addr, 1, data, 1) == 0) { + return data[0]; + } + } + + return 0; } void get_spd_info(unsigned long* dimm_populated, unsigned char* iic0_dimm_addr, unsigned long num_dimm_banks) { - unsigned long dimm_num; - unsigned long dimm_found; - unsigned char num_of_bytes; - unsigned char total_size; - - dimm_found = FALSE; - for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { - num_of_bytes = 0; - total_size = 0; - - num_of_bytes = spd_read(iic0_dimm_addr[dimm_num], 0); - total_size = spd_read(iic0_dimm_addr[dimm_num], 1); - - if ((num_of_bytes != 0) && (total_size != 0)) { - dimm_populated[dimm_num] = TRUE; - dimm_found = TRUE; + unsigned long dimm_num; + unsigned long dimm_found; + unsigned char num_of_bytes; + unsigned char total_size; + + dimm_found = FALSE; + for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { + num_of_bytes = 0; + total_size = 0; + + num_of_bytes = spd_read(iic0_dimm_addr[dimm_num], 0); + total_size = spd_read(iic0_dimm_addr[dimm_num], 1); + + if ((num_of_bytes != 0) && (total_size != 0)) { + dimm_populated[dimm_num] = TRUE; + dimm_found = TRUE; #if 0 - printf("DIMM slot %lu: populated\n", dimm_num); + printf("DIMM slot %lu: populated\n", dimm_num); #endif - } - else { - dimm_populated[dimm_num] = FALSE; + } else { + dimm_populated[dimm_num] = FALSE; #if 0 - printf("DIMM slot %lu: Not populated\n", dimm_num); + printf("DIMM slot %lu: Not populated\n", dimm_num); #endif + } } - } - if (dimm_found == FALSE) { - printf("ERROR - No memory installed. Install a DDR-SDRAM DIMM.\n\n"); - hang(); - } + if (dimm_found == FALSE) { + printf("ERROR - No memory installed. Install a DDR-SDRAM DIMM.\n\n"); + hang(); + } } void check_mem_type(unsigned long* dimm_populated, unsigned char* iic0_dimm_addr, unsigned long num_dimm_banks) { - unsigned long dimm_num; - unsigned char dimm_type; - - for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { - if (dimm_populated[dimm_num] == TRUE) { - dimm_type = spd_read(iic0_dimm_addr[dimm_num], 2); - switch (dimm_type) { - case 7: + unsigned long dimm_num; + unsigned char dimm_type; + + for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { + if (dimm_populated[dimm_num] == TRUE) { + dimm_type = spd_read(iic0_dimm_addr[dimm_num], 2); + switch (dimm_type) { + case 7: #if 0 - printf("DIMM slot %lu: DDR SDRAM detected\n", dimm_num); + printf("DIMM slot %lu: DDR SDRAM detected\n", dimm_num); #endif - break; - default: - printf("ERROR: Unsupported DIMM detected in slot %lu.\n", - dimm_num); - printf("Only DDR SDRAM DIMMs are supported.\n"); - printf("Replace the DIMM module with a supported DIMM.\n\n"); - hang(); - break; - } + break; + default: + printf("ERROR: Unsupported DIMM detected in slot %lu.\n", + dimm_num); + printf("Only DDR SDRAM DIMMs are supported.\n"); + printf("Replace the DIMM module with a supported DIMM.\n\n"); + hang(); + break; + } + } } - } } @@ -924,894 +888,877 @@ void check_volt_type(unsigned long* dimm_populated, unsigned char* iic0_dimm_addr, unsigned long num_dimm_banks) { - unsigned long dimm_num; - unsigned long voltage_type; - - for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { - if (dimm_populated[dimm_num] == TRUE) { - voltage_type = spd_read(iic0_dimm_addr[dimm_num], 8); - if (voltage_type != 0x04) { - printf("ERROR: DIMM %lu with unsupported voltage level.\n", - dimm_num); - hang(); - } - else { + unsigned long dimm_num; + unsigned long voltage_type; + + for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { + if (dimm_populated[dimm_num] == TRUE) { + voltage_type = spd_read(iic0_dimm_addr[dimm_num], 8); + if (voltage_type != 0x04) { + printf("ERROR: DIMM %lu with unsupported voltage level.\n", + dimm_num); + hang(); + } else { #if 0 - printf("DIMM %lu voltage level supported.\n", dimm_num); + printf("DIMM %lu voltage level supported.\n", dimm_num); #endif - } - break; + } + break; + } } - } } void program_cfg0(unsigned long* dimm_populated, unsigned char* iic0_dimm_addr, unsigned long num_dimm_banks) { - unsigned long dimm_num; - unsigned long cfg0; - unsigned long ecc_enabled; - unsigned char ecc; - unsigned char attributes; - unsigned long data_width; - unsigned long dimm_32bit; - unsigned long dimm_64bit; - - /* - * get Memory Controller Options 0 data - */ - mfsdram(mem_cfg0, cfg0); - - /* - * clear bits - */ - cfg0 &= ~(SDRAM_CFG0_DCEN | SDRAM_CFG0_MCHK_MASK | - SDRAM_CFG0_RDEN | SDRAM_CFG0_PMUD | - SDRAM_CFG0_DMWD_MASK | - SDRAM_CFG0_UIOS_MASK | SDRAM_CFG0_PDP); - - - /* - * FIXME: assume the DDR SDRAMs in both banks are the same - */ - ecc_enabled = TRUE; - for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { - if (dimm_populated[dimm_num] == TRUE) { - ecc = spd_read(iic0_dimm_addr[dimm_num], 11); - if (ecc != 0x02) { - ecc_enabled = FALSE; - } - - /* - * program Registered DIMM Enable - */ - attributes = spd_read(iic0_dimm_addr[dimm_num], 21); - if ((attributes & 0x02) != 0x00) { - cfg0 |= SDRAM_CFG0_RDEN; - } - - /* - * program DDR SDRAM Data Width - */ - data_width = - (unsigned long)spd_read(iic0_dimm_addr[dimm_num],6) + - (((unsigned long)spd_read(iic0_dimm_addr[dimm_num],7)) << 8); - if (data_width == 64 || data_width == 72) { - dimm_64bit = TRUE; - cfg0 |= SDRAM_CFG0_DMWD_64; - } - else if (data_width == 32 || data_width == 40) { - dimm_32bit = TRUE; - cfg0 |= SDRAM_CFG0_DMWD_32; - } - else { - printf("WARNING: DIMM with datawidth of %lu bits.\n", - data_width); - printf("Only DIMMs with 32 or 64 bit datawidths supported.\n"); - hang(); - } - break; + unsigned long dimm_num; + unsigned long cfg0; + unsigned long ecc_enabled; + unsigned char ecc; + unsigned char attributes; + unsigned long data_width; + unsigned long dimm_32bit; + unsigned long dimm_64bit; + + /* + * get Memory Controller Options 0 data + */ + mfsdram(mem_cfg0, cfg0); + + /* + * clear bits + */ + cfg0 &= ~(SDRAM_CFG0_DCEN | SDRAM_CFG0_MCHK_MASK | + SDRAM_CFG0_RDEN | SDRAM_CFG0_PMUD | + SDRAM_CFG0_DMWD_MASK | + SDRAM_CFG0_UIOS_MASK | SDRAM_CFG0_PDP); + + + /* + * FIXME: assume the DDR SDRAMs in both banks are the same + */ + ecc_enabled = TRUE; + for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { + if (dimm_populated[dimm_num] == TRUE) { + ecc = spd_read(iic0_dimm_addr[dimm_num], 11); + if (ecc != 0x02) { + ecc_enabled = FALSE; + } + + /* + * program Registered DIMM Enable + */ + attributes = spd_read(iic0_dimm_addr[dimm_num], 21); + if ((attributes & 0x02) != 0x00) { + cfg0 |= SDRAM_CFG0_RDEN; + } + + /* + * program DDR SDRAM Data Width + */ + data_width = + (unsigned long)spd_read(iic0_dimm_addr[dimm_num],6) + + (((unsigned long)spd_read(iic0_dimm_addr[dimm_num],7)) << 8); + if (data_width == 64 || data_width == 72) { + dimm_64bit = TRUE; + cfg0 |= SDRAM_CFG0_DMWD_64; + } else if (data_width == 32 || data_width == 40) { + dimm_32bit = TRUE; + cfg0 |= SDRAM_CFG0_DMWD_32; + } else { + printf("WARNING: DIMM with datawidth of %lu bits.\n", + data_width); + printf("Only DIMMs with 32 or 64 bit datawidths supported.\n"); + hang(); + } + break; + } } - } - - /* - * program Memory Data Error Checking - */ - if (ecc_enabled == TRUE) { - cfg0 |= SDRAM_CFG0_MCHK_GEN; - } - else { - cfg0 |= SDRAM_CFG0_MCHK_NON; - } - - /* - * program Page Management Unit - */ - cfg0 |= SDRAM_CFG0_PMUD; - - /* - * program Memory Controller Options 0 - * Note: DCEN must be enabled after all DDR SDRAM controller - * configuration registers get initialized. - */ - mtsdram(mem_cfg0, cfg0); + + /* + * program Memory Data Error Checking + */ + if (ecc_enabled == TRUE) { + cfg0 |= SDRAM_CFG0_MCHK_GEN; + } else { + cfg0 |= SDRAM_CFG0_MCHK_NON; + } + + /* + * program Page Management Unit + */ + cfg0 |= SDRAM_CFG0_PMUD; + + /* + * program Memory Controller Options 0 + * Note: DCEN must be enabled after all DDR SDRAM controller + * configuration registers get initialized. + */ + mtsdram(mem_cfg0, cfg0); } void program_cfg1(unsigned long* dimm_populated, unsigned char* iic0_dimm_addr, unsigned long num_dimm_banks) { - unsigned long cfg1; - mfsdram(mem_cfg1, cfg1); - - /* - * Self-refresh exit, disable PM - */ - cfg1 &= ~(SDRAM_CFG1_SRE | SDRAM_CFG1_PMEN); - - /* - * program Memory Controller Options 1 - */ - mtsdram(mem_cfg1, cfg1); + unsigned long cfg1; + mfsdram(mem_cfg1, cfg1); + + /* + * Self-refresh exit, disable PM + */ + cfg1 &= ~(SDRAM_CFG1_SRE | SDRAM_CFG1_PMEN); + + /* + * program Memory Controller Options 1 + */ + mtsdram(mem_cfg1, cfg1); } void program_rtr (unsigned long* dimm_populated, unsigned char* iic0_dimm_addr, unsigned long num_dimm_banks) { - unsigned long dimm_num; - unsigned long bus_period_x_10; - unsigned long refresh_rate = 0; - unsigned char refresh_rate_type; - unsigned long refresh_interval; - unsigned long sdram_rtr; - PPC440_SYS_INFO sys_info; - - /* - * get the board info - */ - get_sys_info(&sys_info); - bus_period_x_10 = ONE_BILLION / (sys_info.freqPLB / 10); - - - for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { - if (dimm_populated[dimm_num] == TRUE) { - refresh_rate_type = 0x7F & spd_read(iic0_dimm_addr[dimm_num], 12); - switch (refresh_rate_type) { - case 0x00: - refresh_rate = 15625; - break; - case 0x01: - refresh_rate = 15625/4; - break; - case 0x02: - refresh_rate = 15625/2; - break; - case 0x03: - refresh_rate = 15626*2; - break; - case 0x04: - refresh_rate = 15625*4; - break; - case 0x05: - refresh_rate = 15625*8; - break; - default: - printf("ERROR: DIMM %lu, unsupported refresh rate/type.\n", - dimm_num); - printf("Replace the DIMM module with a supported DIMM.\n"); - break; - } + unsigned long dimm_num; + unsigned long bus_period_x_10; + unsigned long refresh_rate = 0; + unsigned char refresh_rate_type; + unsigned long refresh_interval; + unsigned long sdram_rtr; + PPC440_SYS_INFO sys_info; + + /* + * get the board info + */ + get_sys_info(&sys_info); + bus_period_x_10 = ONE_BILLION / (sys_info.freqPLB / 10); + - break; + for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { + if (dimm_populated[dimm_num] == TRUE) { + refresh_rate_type = 0x7F & spd_read(iic0_dimm_addr[dimm_num], 12); + switch (refresh_rate_type) { + case 0x00: + refresh_rate = 15625; + break; + case 0x01: + refresh_rate = 15625/4; + break; + case 0x02: + refresh_rate = 15625/2; + break; + case 0x03: + refresh_rate = 15626*2; + break; + case 0x04: + refresh_rate = 15625*4; + break; + case 0x05: + refresh_rate = 15625*8; + break; + default: + printf("ERROR: DIMM %lu, unsupported refresh rate/type.\n", + dimm_num); + printf("Replace the DIMM module with a supported DIMM.\n"); + break; + } + + break; + } } - } - refresh_interval = refresh_rate * 10 / bus_period_x_10; - sdram_rtr = (refresh_interval & 0x3ff8) << 16; + refresh_interval = refresh_rate * 10 / bus_period_x_10; + sdram_rtr = (refresh_interval & 0x3ff8) << 16; - /* - * program Refresh Timer Register (SDRAM0_RTR) - */ - mtsdram(mem_rtr, sdram_rtr); + /* + * program Refresh Timer Register (SDRAM0_RTR) + */ + mtsdram(mem_rtr, sdram_rtr); } void program_tr0 (unsigned long* dimm_populated, unsigned char* iic0_dimm_addr, unsigned long num_dimm_banks) { - unsigned long dimm_num; - unsigned long tr0; - unsigned char wcsbc; - unsigned char t_rp_ns; - unsigned char t_rcd_ns; - unsigned char t_ras_ns; - unsigned long t_rp_clk; - unsigned long t_ras_rcd_clk; - unsigned long t_rcd_clk; - unsigned long t_rfc_clk; - unsigned long plb_check; - unsigned char cas_bit; - unsigned long cas_index; - unsigned char cas_2_0_available; - unsigned char cas_2_5_available; - unsigned char cas_3_0_available; - unsigned long cycle_time_ns_x_10[3]; - unsigned long tcyc_3_0_ns_x_10; - unsigned long tcyc_2_5_ns_x_10; - unsigned long tcyc_2_0_ns_x_10; - unsigned long tcyc_reg; - unsigned long bus_period_x_10; - PPC440_SYS_INFO sys_info; - unsigned long residue; - - /* - * get the board info - */ - get_sys_info(&sys_info); - bus_period_x_10 = ONE_BILLION / (sys_info.freqPLB / 10); - - /* - * get SDRAM Timing Register 0 (SDRAM_TR0) and clear bits - */ - mfsdram(mem_tr0, tr0); - tr0 &= ~(SDRAM_TR0_SDWR_MASK | SDRAM_TR0_SDWD_MASK | - SDRAM_TR0_SDCL_MASK | SDRAM_TR0_SDPA_MASK | - SDRAM_TR0_SDCP_MASK | SDRAM_TR0_SDLD_MASK | - SDRAM_TR0_SDRA_MASK | SDRAM_TR0_SDRD_MASK); - - /* - * initialization - */ - wcsbc = 0; - t_rp_ns = 0; - t_rcd_ns = 0; - t_ras_ns = 0; - cas_2_0_available = TRUE; - cas_2_5_available = TRUE; - cas_3_0_available = TRUE; - tcyc_2_0_ns_x_10 = 0; - tcyc_2_5_ns_x_10 = 0; - tcyc_3_0_ns_x_10 = 0; - - for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { - if (dimm_populated[dimm_num] == TRUE) { - wcsbc = spd_read(iic0_dimm_addr[dimm_num], 15); - t_rp_ns = spd_read(iic0_dimm_addr[dimm_num], 27) >> 2; - t_rcd_ns = spd_read(iic0_dimm_addr[dimm_num], 29) >> 2; - t_ras_ns = spd_read(iic0_dimm_addr[dimm_num], 30); - cas_bit = spd_read(iic0_dimm_addr[dimm_num], 18); - - for (cas_index = 0; cas_index < 3; cas_index++) { - switch (cas_index) { - case 0: - tcyc_reg = spd_read(iic0_dimm_addr[dimm_num], 9); - break; - case 1: - tcyc_reg = spd_read(iic0_dimm_addr[dimm_num], 23); - break; - default: - tcyc_reg = spd_read(iic0_dimm_addr[dimm_num], 25); - break; - } + unsigned long dimm_num; + unsigned long tr0; + unsigned char wcsbc; + unsigned char t_rp_ns; + unsigned char t_rcd_ns; + unsigned char t_ras_ns; + unsigned long t_rp_clk; + unsigned long t_ras_rcd_clk; + unsigned long t_rcd_clk; + unsigned long t_rfc_clk; + unsigned long plb_check; + unsigned char cas_bit; + unsigned long cas_index; + unsigned char cas_2_0_available; + unsigned char cas_2_5_available; + unsigned char cas_3_0_available; + unsigned long cycle_time_ns_x_10[3]; + unsigned long tcyc_3_0_ns_x_10; + unsigned long tcyc_2_5_ns_x_10; + unsigned long tcyc_2_0_ns_x_10; + unsigned long tcyc_reg; + unsigned long bus_period_x_10; + PPC440_SYS_INFO sys_info; + unsigned long residue; - if ((tcyc_reg & 0x0F) >= 10) { - printf("ERROR: Tcyc incorrect for DIMM in slot %lu\n", - dimm_num); - hang(); - } + /* + * get the board info + */ + get_sys_info(&sys_info); + bus_period_x_10 = ONE_BILLION / (sys_info.freqPLB / 10); - cycle_time_ns_x_10[cas_index] = - (((tcyc_reg & 0xF0) >> 4) * 10) + (tcyc_reg & 0x0F); - } - - cas_index = 0; - - if ((cas_bit & 0x80) != 0) { - cas_index += 3; - } - else if ((cas_bit & 0x40) != 0) { - cas_index += 2; - } - else if ((cas_bit & 0x20) != 0) { - cas_index += 1; - } - - if (((cas_bit & 0x10) != 0) && (cas_index < 3)) { - tcyc_3_0_ns_x_10 = cycle_time_ns_x_10[cas_index]; - cas_index++; - } - else { - if (cas_index != 0) { - cas_index++; - } - cas_3_0_available = FALSE; - } - - if (((cas_bit & 0x08) != 0) || (cas_index < 3)) { - tcyc_2_5_ns_x_10 = cycle_time_ns_x_10[cas_index]; - cas_index++; - } - else { - if (cas_index != 0) { - cas_index++; - } - cas_2_5_available = FALSE; - } - - if (((cas_bit & 0x04) != 0) || (cas_index < 3)) { - tcyc_2_0_ns_x_10 = cycle_time_ns_x_10[cas_index]; - cas_index++; - } - else { - if (cas_index != 0) { - cas_index++; + /* + * get SDRAM Timing Register 0 (SDRAM_TR0) and clear bits + */ + mfsdram(mem_tr0, tr0); + tr0 &= ~(SDRAM_TR0_SDWR_MASK | SDRAM_TR0_SDWD_MASK | + SDRAM_TR0_SDCL_MASK | SDRAM_TR0_SDPA_MASK | + SDRAM_TR0_SDCP_MASK | SDRAM_TR0_SDLD_MASK | + SDRAM_TR0_SDRA_MASK | SDRAM_TR0_SDRD_MASK); + + /* + * initialization + */ + wcsbc = 0; + t_rp_ns = 0; + t_rcd_ns = 0; + t_ras_ns = 0; + cas_2_0_available = TRUE; + cas_2_5_available = TRUE; + cas_3_0_available = TRUE; + tcyc_2_0_ns_x_10 = 0; + tcyc_2_5_ns_x_10 = 0; + tcyc_3_0_ns_x_10 = 0; + + for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { + if (dimm_populated[dimm_num] == TRUE) { + wcsbc = spd_read(iic0_dimm_addr[dimm_num], 15); + t_rp_ns = spd_read(iic0_dimm_addr[dimm_num], 27) >> 2; + t_rcd_ns = spd_read(iic0_dimm_addr[dimm_num], 29) >> 2; + t_ras_ns = spd_read(iic0_dimm_addr[dimm_num], 30); + cas_bit = spd_read(iic0_dimm_addr[dimm_num], 18); + + for (cas_index = 0; cas_index < 3; cas_index++) { + switch (cas_index) { + case 0: + tcyc_reg = spd_read(iic0_dimm_addr[dimm_num], 9); + break; + case 1: + tcyc_reg = spd_read(iic0_dimm_addr[dimm_num], 23); + break; + default: + tcyc_reg = spd_read(iic0_dimm_addr[dimm_num], 25); + break; + } + + if ((tcyc_reg & 0x0F) >= 10) { + printf("ERROR: Tcyc incorrect for DIMM in slot %lu\n", + dimm_num); + hang(); + } + + cycle_time_ns_x_10[cas_index] = + (((tcyc_reg & 0xF0) >> 4) * 10) + (tcyc_reg & 0x0F); + } + + cas_index = 0; + + if ((cas_bit & 0x80) != 0) { + cas_index += 3; + } else if ((cas_bit & 0x40) != 0) { + cas_index += 2; + } else if ((cas_bit & 0x20) != 0) { + cas_index += 1; + } + + if (((cas_bit & 0x10) != 0) && (cas_index < 3)) { + tcyc_3_0_ns_x_10 = cycle_time_ns_x_10[cas_index]; + cas_index++; + } else { + if (cas_index != 0) { + cas_index++; + } + cas_3_0_available = FALSE; + } + + if (((cas_bit & 0x08) != 0) || (cas_index < 3)) { + tcyc_2_5_ns_x_10 = cycle_time_ns_x_10[cas_index]; + cas_index++; + } else { + if (cas_index != 0) { + cas_index++; + } + cas_2_5_available = FALSE; + } + + if (((cas_bit & 0x04) != 0) || (cas_index < 3)) { + tcyc_2_0_ns_x_10 = cycle_time_ns_x_10[cas_index]; + cas_index++; + } else { + if (cas_index != 0) { + cas_index++; + } + cas_2_0_available = FALSE; + } + + break; } - cas_2_0_available = FALSE; - } + } + + /* + * Program SD_WR and SD_WCSBC fields + */ + tr0 |= SDRAM_TR0_SDWR_2_CLK; /* Write Recovery: 2 CLK */ + switch (wcsbc) { + case 0: + tr0 |= SDRAM_TR0_SDWD_0_CLK; + break; + default: + tr0 |= SDRAM_TR0_SDWD_1_CLK; + break; + } + + /* + * Program SD_CASL field + */ + if ((cas_2_0_available == TRUE) && + (bus_period_x_10 >= tcyc_2_0_ns_x_10)) { + tr0 |= SDRAM_TR0_SDCL_2_0_CLK; + } else if ((cas_2_5_available == TRUE) && + (bus_period_x_10 >= tcyc_2_5_ns_x_10)) { + tr0 |= SDRAM_TR0_SDCL_2_5_CLK; + } else if ((cas_3_0_available == TRUE) && + (bus_period_x_10 >= tcyc_3_0_ns_x_10)) { + tr0 |= SDRAM_TR0_SDCL_3_0_CLK; + } else { + printf("ERROR: No supported CAS latency with the installed DIMMs.\n"); + printf("Only CAS latencies of 2.0, 2.5, and 3.0 are supported.\n"); + printf("Make sure the PLB speed is within the supported range.\n"); + hang(); + } + + /* + * Calculate Trp in clock cycles and round up if necessary + * Program SD_PTA field + */ + t_rp_clk = sys_info.freqPLB * t_rp_ns / ONE_BILLION; + plb_check = ONE_BILLION * t_rp_clk / t_rp_ns; + if (sys_info.freqPLB != plb_check) { + t_rp_clk++; + } + switch ((unsigned long)t_rp_clk) { + case 0: + case 1: + case 2: + tr0 |= SDRAM_TR0_SDPA_2_CLK; + break; + case 3: + tr0 |= SDRAM_TR0_SDPA_3_CLK; + break; + default: + tr0 |= SDRAM_TR0_SDPA_4_CLK; + break; + } + + /* + * Program SD_CTP field + */ + t_ras_rcd_clk = sys_info.freqPLB * (t_ras_ns - t_rcd_ns) / ONE_BILLION; + plb_check = ONE_BILLION * t_ras_rcd_clk / (t_ras_ns - t_rcd_ns); + if (sys_info.freqPLB != plb_check) { + t_ras_rcd_clk++; + } + switch (t_ras_rcd_clk) { + case 0: + case 1: + case 2: + tr0 |= SDRAM_TR0_SDCP_2_CLK; + break; + case 3: + tr0 |= SDRAM_TR0_SDCP_3_CLK; + break; + case 4: + tr0 |= SDRAM_TR0_SDCP_4_CLK; + break; + default: + tr0 |= SDRAM_TR0_SDCP_5_CLK; + break; + } + + /* + * Program SD_LDF field + */ + tr0 |= SDRAM_TR0_SDLD_2_CLK; + + /* + * Program SD_RFTA field + * FIXME tRFC hardcoded as 75 nanoseconds + */ + t_rfc_clk = sys_info.freqPLB / (ONE_BILLION / 75); + residue = sys_info.freqPLB % (ONE_BILLION / 75); + if (residue >= (ONE_BILLION / 150)) { + t_rfc_clk++; + } + switch (t_rfc_clk) { + case 0: + case 1: + case 2: + case 3: + case 4: + case 5: + case 6: + tr0 |= SDRAM_TR0_SDRA_6_CLK; + break; + case 7: + tr0 |= SDRAM_TR0_SDRA_7_CLK; + break; + case 8: + tr0 |= SDRAM_TR0_SDRA_8_CLK; + break; + case 9: + tr0 |= SDRAM_TR0_SDRA_9_CLK; + break; + case 10: + tr0 |= SDRAM_TR0_SDRA_10_CLK; + break; + case 11: + tr0 |= SDRAM_TR0_SDRA_11_CLK; + break; + case 12: + tr0 |= SDRAM_TR0_SDRA_12_CLK; + break; + default: + tr0 |= SDRAM_TR0_SDRA_13_CLK; + break; + } - break; + /* + * Program SD_RCD field + */ + t_rcd_clk = sys_info.freqPLB * t_rcd_ns / ONE_BILLION; + plb_check = ONE_BILLION * t_rcd_clk / t_rcd_ns; + if (sys_info.freqPLB != plb_check) { + t_rcd_clk++; + } + switch (t_rcd_clk) { + case 0: + case 1: + case 2: + tr0 |= SDRAM_TR0_SDRD_2_CLK; + break; + case 3: + tr0 |= SDRAM_TR0_SDRD_3_CLK; + break; + default: + tr0 |= SDRAM_TR0_SDRD_4_CLK; + break; } - } - - /* - * Program SD_WR and SD_WCSBC fields - */ - tr0 |= SDRAM_TR0_SDWR_2_CLK; /* Write Recovery: 2 CLK */ - switch (wcsbc) { - case 0: - tr0 |= SDRAM_TR0_SDWD_0_CLK; - break; - default: - tr0 |= SDRAM_TR0_SDWD_1_CLK; - break; - } - - /* - * Program SD_CASL field - */ - if ((cas_2_0_available == TRUE) && - (bus_period_x_10 >= tcyc_2_0_ns_x_10)) { - tr0 |= SDRAM_TR0_SDCL_2_0_CLK; - } - else if((cas_2_5_available == TRUE) && - (bus_period_x_10 >= tcyc_2_5_ns_x_10)) { - tr0 |= SDRAM_TR0_SDCL_2_5_CLK; - } - else if((cas_3_0_available == TRUE) && - (bus_period_x_10 >= tcyc_3_0_ns_x_10)) { - tr0 |= SDRAM_TR0_SDCL_3_0_CLK; - } - else { - printf("ERROR: No supported CAS latency with the installed DIMMs.\n"); - printf("Only CAS latencies of 2.0, 2.5, and 3.0 are supported.\n"); - printf("Make sure the PLB speed is within the supported range.\n"); - hang(); - } - - /* - * Calculate Trp in clock cycles and round up if necessary - * Program SD_PTA field - */ - t_rp_clk = sys_info.freqPLB * t_rp_ns / ONE_BILLION; - plb_check = ONE_BILLION * t_rp_clk / t_rp_ns; - if (sys_info.freqPLB != plb_check) { - t_rp_clk++; - } - switch ((unsigned long)t_rp_clk) { - case 0: - case 1: - case 2: - tr0 |= SDRAM_TR0_SDPA_2_CLK; - break; - case 3: - tr0 |= SDRAM_TR0_SDPA_3_CLK; - break; - default: - tr0 |= SDRAM_TR0_SDPA_4_CLK; - break; - } - - /* - * Program SD_CTP field - */ - t_ras_rcd_clk = sys_info.freqPLB * (t_ras_ns - t_rcd_ns) / ONE_BILLION; - plb_check = ONE_BILLION * t_ras_rcd_clk / (t_ras_ns - t_rcd_ns); - if (sys_info.freqPLB != plb_check) { - t_ras_rcd_clk++; - } - switch (t_ras_rcd_clk) { - case 0: - case 1: - case 2: - tr0 |= SDRAM_TR0_SDCP_2_CLK; - break; - case 3: - tr0 |= SDRAM_TR0_SDCP_3_CLK; - break; - case 4: - tr0 |= SDRAM_TR0_SDCP_4_CLK; - break; - default: - tr0 |= SDRAM_TR0_SDCP_5_CLK; - break; - } - - /* - * Program SD_LDF field - */ - tr0 |= SDRAM_TR0_SDLD_2_CLK; - - /* - * Program SD_RFTA field - * FIXME tRFC hardcoded as 75 nanoseconds - */ - t_rfc_clk = sys_info.freqPLB / (ONE_BILLION / 75); - residue = sys_info.freqPLB % (ONE_BILLION / 75); - if (residue >= (ONE_BILLION / 150)) { - t_rfc_clk++; - } - switch (t_rfc_clk) { - case 0: - case 1: - case 2: - case 3: - case 4: - case 5: - case 6: - tr0 |= SDRAM_TR0_SDRA_6_CLK; - break; - case 7: - tr0 |= SDRAM_TR0_SDRA_7_CLK; - break; - case 8: - tr0 |= SDRAM_TR0_SDRA_8_CLK; - break; - case 9: - tr0 |= SDRAM_TR0_SDRA_9_CLK; - break; - case 10: - tr0 |= SDRAM_TR0_SDRA_10_CLK; - break; - case 11: - tr0 |= SDRAM_TR0_SDRA_11_CLK; - break; - case 12: - tr0 |= SDRAM_TR0_SDRA_12_CLK; - break; - default: - tr0 |= SDRAM_TR0_SDRA_13_CLK; - break; - } - - /* - * Program SD_RCD field - */ - t_rcd_clk = sys_info.freqPLB * t_rcd_ns / ONE_BILLION; - plb_check = ONE_BILLION * t_rcd_clk / t_rcd_ns; - if (sys_info.freqPLB != plb_check) { - t_rcd_clk++; - } - switch (t_rcd_clk) { - case 0: - case 1: - case 2: - tr0 |= SDRAM_TR0_SDRD_2_CLK; - break; - case 3: - tr0 |= SDRAM_TR0_SDRD_3_CLK; - break; - default: - tr0 |= SDRAM_TR0_SDRD_4_CLK; - break; - } #if 0 - printf("tr0: %x\n", tr0); + printf("tr0: %x\n", tr0); #endif - mtsdram(mem_tr0, tr0); + mtsdram(mem_tr0, tr0); } void program_tr1 (void) { - unsigned long tr0; - unsigned long tr1; - unsigned long cfg0; - unsigned long ecc_temp; - unsigned long dlycal; - unsigned long dly_val; - unsigned long i, j, k; - unsigned long bxcr_num; - unsigned long max_pass_length; - unsigned long current_pass_length; - unsigned long current_fail_length; - unsigned long current_start; - unsigned long rdclt; - unsigned long rdclt_offset; - long max_start; - long max_end; - long rdclt_average; - unsigned char window_found; - unsigned char fail_found; - unsigned char pass_found; - unsigned long * membase; - PPC440_SYS_INFO sys_info; - - /* - * get the board info - */ - get_sys_info(&sys_info); - - /* - * get SDRAM Timing Register 0 (SDRAM_TR0) and clear bits - */ - mfsdram(mem_tr1, tr1); - tr1 &= ~(SDRAM_TR1_RDSS_MASK | SDRAM_TR1_RDSL_MASK | - SDRAM_TR1_RDCD_MASK | SDRAM_TR1_RDCT_MASK); - - mfsdram(mem_tr0, tr0); - if (((tr0 & SDRAM_TR0_SDCL_MASK) == SDRAM_TR0_SDCL_2_5_CLK) && - (sys_info.freqPLB > 100000000)) { - tr1 |= SDRAM_TR1_RDSS_TR2; - tr1 |= SDRAM_TR1_RDSL_STAGE3; - tr1 |= SDRAM_TR1_RDCD_RCD_1_2; - } - else { - tr1 |= SDRAM_TR1_RDSS_TR1; - tr1 |= SDRAM_TR1_RDSL_STAGE2; - tr1 |= SDRAM_TR1_RDCD_RCD_0_0; - } - - /* - * save CFG0 ECC setting to a temporary variable and turn ECC off - */ - mfsdram(mem_cfg0, cfg0); - ecc_temp = cfg0 & SDRAM_CFG0_MCHK_MASK; - mtsdram(mem_cfg0, (cfg0 & ~SDRAM_CFG0_MCHK_MASK) | SDRAM_CFG0_MCHK_NON); - - /* - * get the delay line calibration register value - */ - mfsdram(mem_dlycal, dlycal); - dly_val = SDRAM_DLYCAL_DLCV_DECODE(dlycal) << 2; - - max_pass_length = 0; - max_start = 0; - max_end = 0; - current_pass_length = 0; - current_fail_length = 0; - current_start = 0; - rdclt_offset = 0; - window_found = FALSE; - fail_found = FALSE; - pass_found = FALSE; + unsigned long tr0; + unsigned long tr1; + unsigned long cfg0; + unsigned long ecc_temp; + unsigned long dlycal; + unsigned long dly_val; + unsigned long i, j, k; + unsigned long bxcr_num; + unsigned long max_pass_length; + unsigned long current_pass_length; + unsigned long current_fail_length; + unsigned long current_start; + unsigned long rdclt; + unsigned long rdclt_offset; + long max_start; + long max_end; + long rdclt_average; + unsigned char window_found; + unsigned char fail_found; + unsigned char pass_found; + unsigned long * membase; + PPC440_SYS_INFO sys_info; + + /* + * get the board info + */ + get_sys_info(&sys_info); + + /* + * get SDRAM Timing Register 0 (SDRAM_TR0) and clear bits + */ + mfsdram(mem_tr1, tr1); + tr1 &= ~(SDRAM_TR1_RDSS_MASK | SDRAM_TR1_RDSL_MASK | + SDRAM_TR1_RDCD_MASK | SDRAM_TR1_RDCT_MASK); + + mfsdram(mem_tr0, tr0); + if (((tr0 & SDRAM_TR0_SDCL_MASK) == SDRAM_TR0_SDCL_2_5_CLK) && + (sys_info.freqPLB > 100000000)) { + tr1 |= SDRAM_TR1_RDSS_TR2; + tr1 |= SDRAM_TR1_RDSL_STAGE3; + tr1 |= SDRAM_TR1_RDCD_RCD_1_2; + } else { + tr1 |= SDRAM_TR1_RDSS_TR1; + tr1 |= SDRAM_TR1_RDSL_STAGE2; + tr1 |= SDRAM_TR1_RDCD_RCD_0_0; + } + + /* + * save CFG0 ECC setting to a temporary variable and turn ECC off + */ + mfsdram(mem_cfg0, cfg0); + ecc_temp = cfg0 & SDRAM_CFG0_MCHK_MASK; + mtsdram(mem_cfg0, (cfg0 & ~SDRAM_CFG0_MCHK_MASK) | SDRAM_CFG0_MCHK_NON); + + /* + * get the delay line calibration register value + */ + mfsdram(mem_dlycal, dlycal); + dly_val = SDRAM_DLYCAL_DLCV_DECODE(dlycal) << 2; + + max_pass_length = 0; + max_start = 0; + max_end = 0; + current_pass_length = 0; + current_fail_length = 0; + current_start = 0; + rdclt_offset = 0; + window_found = FALSE; + fail_found = FALSE; + pass_found = FALSE; #ifdef DEBUG - printf("Starting memory test "); + printf("Starting memory test "); #endif - for (k = 0; k < NUMHALFCYCLES; k++) { - for (rdclt = 0; rdclt < dly_val; rdclt++) { - /* - * Set the timing reg for the test. - */ - mtsdram(mem_tr1, (tr1 | SDRAM_TR1_RDCT_ENCODE(rdclt))); - - for (bxcr_num = 0; bxcr_num < MAXBXCR; bxcr_num++) { - mtdcr(memcfga, mem_b0cr + (bxcr_num<<2)); - if ((mfdcr(memcfgd) & SDRAM_BXCR_SDBE) == SDRAM_BXCR_SDBE) { - /* Bank is enabled */ - membase = (unsigned long*) - (mfdcr(memcfgd) & SDRAM_BXCR_SDBA_MASK); - - /* - * Run the short memory test - */ - for (i = 0; i < NUMMEMTESTS; i++) { - for (j = 0; j < NUMMEMWORDS; j++) { - membase[j] = test[i][j]; - ppcDcbf((unsigned long)&(membase[j])); + for (k = 0; k < NUMHALFCYCLES; k++) { + for (rdclt = 0; rdclt < dly_val; rdclt++) { + /* + * Set the timing reg for the test. + */ + mtsdram(mem_tr1, (tr1 | SDRAM_TR1_RDCT_ENCODE(rdclt))); + + for (bxcr_num = 0; bxcr_num < MAXBXCR; bxcr_num++) { + mtdcr(memcfga, mem_b0cr + (bxcr_num<<2)); + if ((mfdcr(memcfgd) & SDRAM_BXCR_SDBE) == SDRAM_BXCR_SDBE) { + /* Bank is enabled */ + membase = (unsigned long*) + (mfdcr(memcfgd) & SDRAM_BXCR_SDBA_MASK); + + /* + * Run the short memory test + */ + for (i = 0; i < NUMMEMTESTS; i++) { + for (j = 0; j < NUMMEMWORDS; j++) { + membase[j] = test[i][j]; + ppcDcbf((unsigned long)&(membase[j])); + } + + for (j = 0; j < NUMMEMWORDS; j++) { + if (membase[j] != test[i][j]) { + ppcDcbf((unsigned long)&(membase[j])); + break; + } + ppcDcbf((unsigned long)&(membase[j])); + } + + if (j < NUMMEMWORDS) { + break; + } + } + + /* + * see if the rdclt value passed + */ + if (i < NUMMEMTESTS) { + break; + } + } } - for (j = 0; j < NUMMEMWORDS; j++) { - if (membase[j] != test[i][j]) { - ppcDcbf((unsigned long)&(membase[j])); - break; - } - ppcDcbf((unsigned long)&(membase[j])); + if (bxcr_num == MAXBXCR) { + if (fail_found == TRUE) { + pass_found = TRUE; + if (current_pass_length == 0) { + current_start = rdclt_offset + rdclt; + } + + current_fail_length = 0; + current_pass_length++; + + if (current_pass_length > max_pass_length) { + max_pass_length = current_pass_length; + max_start = current_start; + max_end = rdclt_offset + rdclt; + } + } + } else { + current_pass_length = 0; + current_fail_length++; + + if (current_fail_length >= (dly_val>>2)) { + if (fail_found == FALSE) { + fail_found = TRUE; + } else if (pass_found == TRUE) { + window_found = TRUE; + break; + } + } } - - if (j < NUMMEMWORDS) { - break; - } - } - - /* - * see if the rdclt value passed - */ - if (i < NUMMEMTESTS) { - break; - } } - } - - if (bxcr_num == MAXBXCR) { - if (fail_found == TRUE) { - pass_found = TRUE; - if (current_pass_length == 0) { - current_start = rdclt_offset + rdclt; - } - - current_fail_length = 0; - current_pass_length++; - - if (current_pass_length > max_pass_length) { - max_pass_length = current_pass_length; - max_start = current_start; - max_end = rdclt_offset + rdclt; - } - } - } - else { - current_pass_length = 0; - current_fail_length++; - - if (current_fail_length >= (dly_val>>2)) { - if (fail_found == FALSE) { - fail_found = TRUE; - } - else if (pass_found == TRUE) { - window_found = TRUE; +#ifdef DEBUG + printf("."); +#endif + if (window_found == TRUE) { break; - } } - } + + tr1 = tr1 ^ SDRAM_TR1_RDCD_MASK; + rdclt_offset += dly_val; } #ifdef DEBUG - printf("."); + printf("\n"); #endif - if (window_found == TRUE) { - break; + + /* + * make sure we find the window + */ + if (window_found == FALSE) { + printf("ERROR: Cannot determine a common read delay.\n"); + hang(); } - tr1 = tr1 ^ SDRAM_TR1_RDCD_MASK; - rdclt_offset += dly_val; - } -#ifdef DEBUG - printf("\n"); -#endif + /* + * restore the orignal ECC setting + */ + mtsdram(mem_cfg0, (cfg0 & ~SDRAM_CFG0_MCHK_MASK) | ecc_temp); + + /* + * set the SDRAM TR1 RDCD value + */ + tr1 &= ~SDRAM_TR1_RDCD_MASK; + if ((tr0 & SDRAM_TR0_SDCL_MASK) == SDRAM_TR0_SDCL_2_5_CLK) { + tr1 |= SDRAM_TR1_RDCD_RCD_1_2; + } else { + tr1 |= SDRAM_TR1_RDCD_RCD_0_0; + } - /* - * make sure we find the window - */ - if (window_found == FALSE) { - printf("ERROR: Cannot determine a common read delay.\n"); - hang(); - } - - /* - * restore the orignal ECC setting - */ - mtsdram(mem_cfg0, (cfg0 & ~SDRAM_CFG0_MCHK_MASK) | ecc_temp); - - /* - * set the SDRAM TR1 RDCD value - */ - tr1 &= ~SDRAM_TR1_RDCD_MASK; - if ((tr0 & SDRAM_TR0_SDCL_MASK) == SDRAM_TR0_SDCL_2_5_CLK) { - tr1 |= SDRAM_TR1_RDCD_RCD_1_2; - } - else { - tr1 |= SDRAM_TR1_RDCD_RCD_0_0; - } - - /* - * set the SDRAM TR1 RDCLT value - */ - tr1 &= ~SDRAM_TR1_RDCT_MASK; - while (max_end >= (dly_val<<1)) { - max_end -= (dly_val<<1); - max_start -= (dly_val<<1); - } - - rdclt_average = ((max_start + max_end) >> 1); - if (rdclt_average >= 0x60) - while(1); - - if (rdclt_average < 0) { - rdclt_average = 0; - } - - if (rdclt_average >= dly_val) { - rdclt_average -= dly_val; - tr1 = tr1 ^ SDRAM_TR1_RDCD_MASK; - } - tr1 |= SDRAM_TR1_RDCT_ENCODE(rdclt_average); + /* + * set the SDRAM TR1 RDCLT value + */ + tr1 &= ~SDRAM_TR1_RDCT_MASK; + while (max_end >= (dly_val << 1)) { + max_end -= (dly_val << 1); + max_start -= (dly_val << 1); + } + + rdclt_average = ((max_start + max_end) >> 1); + if (rdclt_average >= 0x60) + while (1) + ; + + if (rdclt_average < 0) { + rdclt_average = 0; + } + + if (rdclt_average >= dly_val) { + rdclt_average -= dly_val; + tr1 = tr1 ^ SDRAM_TR1_RDCD_MASK; + } + tr1 |= SDRAM_TR1_RDCT_ENCODE(rdclt_average); #if 0 - printf("tr1: %x\n", tr1); + printf("tr1: %x\n", tr1); #endif - /* - * program SDRAM Timing Register 1 TR1 - */ - mtsdram(mem_tr1, tr1); + /* + * program SDRAM Timing Register 1 TR1 + */ + mtsdram(mem_tr1, tr1); } unsigned long program_bxcr(unsigned long* dimm_populated, unsigned char* iic0_dimm_addr, unsigned long num_dimm_banks) { - unsigned long dimm_num; - unsigned long bxcr_num; - unsigned long bank_base_addr; - unsigned long bank_size_bytes; - unsigned long cr; - unsigned long i; - unsigned long temp; - unsigned char num_row_addr; - unsigned char num_col_addr; - unsigned char num_banks; - unsigned char bank_size_id; - - - /* - * Set the BxCR regs. First, wipe out the bank config registers. - */ - for (bxcr_num = 0; bxcr_num < MAXBXCR; bxcr_num++) { - mtdcr(memcfga, mem_b0cr + (bxcr_num << 2)); - mtdcr(memcfgd, 0x00000000); - } - - /* - * reset the bank_base address - */ - bank_base_addr = CFG_SDRAM_BASE; - - for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { - if (dimm_populated[dimm_num] == TRUE) { - num_row_addr = spd_read(iic0_dimm_addr[dimm_num], 3); - num_col_addr = spd_read(iic0_dimm_addr[dimm_num], 4); - num_banks = spd_read(iic0_dimm_addr[dimm_num], 5); - bank_size_id = spd_read(iic0_dimm_addr[dimm_num], 31); - - /* - * Set the SDRAM0_BxCR regs - */ - cr = 0; - bank_size_bytes = 4 * 1024 * 1024 * bank_size_id; - switch (bank_size_id) { - case 0x02: - cr |= SDRAM_BXCR_SDSZ_8; - break; - case 0x04: - cr |= SDRAM_BXCR_SDSZ_16; - break; - case 0x08: - cr |= SDRAM_BXCR_SDSZ_32; - break; - case 0x10: - cr |= SDRAM_BXCR_SDSZ_64; - break; - case 0x20: - cr |= SDRAM_BXCR_SDSZ_128; - break; - case 0x40: - cr |= SDRAM_BXCR_SDSZ_256; - break; - case 0x80: - cr |= SDRAM_BXCR_SDSZ_512; - break; - default: - printf("DDR-SDRAM: DIMM %lu BxCR configuration.\n", - dimm_num); - printf("ERROR: Unsupported value for the banksize: %d.\n", - bank_size_id); - printf("Replace the DIMM module with a supported DIMM.\n\n"); - hang(); - } + unsigned long dimm_num; + unsigned long bxcr_num; + unsigned long bank_base_addr; + unsigned long bank_size_bytes; + unsigned long cr; + unsigned long i; + unsigned long temp; + unsigned char num_row_addr; + unsigned char num_col_addr; + unsigned char num_banks; + unsigned char bank_size_id; - switch (num_col_addr) { - case 0x08: - cr |= SDRAM_BXCR_SDAM_1; - break; - case 0x09: - cr |= SDRAM_BXCR_SDAM_2; - break; - case 0x0A: - cr |= SDRAM_BXCR_SDAM_3; - break; - case 0x0B: - cr |= SDRAM_BXCR_SDAM_4; - break; - default: - printf("DDR-SDRAM: DIMM %lu BxCR configuration.\n", - dimm_num); - printf("ERROR: Unsupported value for number of " - "column addresses: %d.\n", num_col_addr); - printf("Replace the DIMM module with a supported DIMM.\n\n"); - hang(); - } - - /* - * enable the bank - */ - cr |= SDRAM_BXCR_SDBE; - - /*------------------------------------------------------------------ - | This next section is hardware dependent and must be programmed - | to match the hardware. - +-----------------------------------------------------------------*/ - if (dimm_num == 0) { - for (i = 0; i < num_banks; i++) { - mtdcr(memcfga, mem_b0cr + (i << 2)); - temp = mfdcr(memcfgd) & ~(SDRAM_BXCR_SDBA_MASK | - SDRAM_BXCR_SDSZ_MASK | - SDRAM_BXCR_SDAM_MASK | - SDRAM_BXCR_SDBE); - cr |= temp; - cr |= bank_base_addr & SDRAM_BXCR_SDBA_MASK; - mtdcr(memcfgd, cr); - bank_base_addr += bank_size_bytes; - } - } - else { - for (i = 0; i < num_banks; i++) { - mtdcr(memcfga, mem_b2cr + (i << 2)); - temp = mfdcr(memcfgd) & ~(SDRAM_BXCR_SDBA_MASK | - SDRAM_BXCR_SDSZ_MASK | - SDRAM_BXCR_SDAM_MASK | - SDRAM_BXCR_SDBE); - cr |= temp; - cr |= bank_base_addr & SDRAM_BXCR_SDBA_MASK; - mtdcr(memcfgd, cr); - bank_base_addr += bank_size_bytes; + + /* + * Set the BxCR regs. First, wipe out the bank config registers. + */ + for (bxcr_num = 0; bxcr_num < MAXBXCR; bxcr_num++) { + mtdcr(memcfga, mem_b0cr + (bxcr_num << 2)); + mtdcr(memcfgd, 0x00000000); + } + + /* + * reset the bank_base address + */ + bank_base_addr = CFG_SDRAM_BASE; + + for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { + if (dimm_populated[dimm_num] == TRUE) { + num_row_addr = spd_read(iic0_dimm_addr[dimm_num], 3); + num_col_addr = spd_read(iic0_dimm_addr[dimm_num], 4); + num_banks = spd_read(iic0_dimm_addr[dimm_num], 5); + bank_size_id = spd_read(iic0_dimm_addr[dimm_num], 31); + + /* + * Set the SDRAM0_BxCR regs + */ + cr = 0; + bank_size_bytes = 4 * 1024 * 1024 * bank_size_id; + switch (bank_size_id) { + case 0x02: + cr |= SDRAM_BXCR_SDSZ_8; + break; + case 0x04: + cr |= SDRAM_BXCR_SDSZ_16; + break; + case 0x08: + cr |= SDRAM_BXCR_SDSZ_32; + break; + case 0x10: + cr |= SDRAM_BXCR_SDSZ_64; + break; + case 0x20: + cr |= SDRAM_BXCR_SDSZ_128; + break; + case 0x40: + cr |= SDRAM_BXCR_SDSZ_256; + break; + case 0x80: + cr |= SDRAM_BXCR_SDSZ_512; + break; + default: + printf("DDR-SDRAM: DIMM %lu BxCR configuration.\n", + dimm_num); + printf("ERROR: Unsupported value for the banksize: %d.\n", + bank_size_id); + printf("Replace the DIMM module with a supported DIMM.\n\n"); + hang(); + } + + switch (num_col_addr) { + case 0x08: + cr |= SDRAM_BXCR_SDAM_1; + break; + case 0x09: + cr |= SDRAM_BXCR_SDAM_2; + break; + case 0x0A: + cr |= SDRAM_BXCR_SDAM_3; + break; + case 0x0B: + cr |= SDRAM_BXCR_SDAM_4; + break; + default: + printf("DDR-SDRAM: DIMM %lu BxCR configuration.\n", + dimm_num); + printf("ERROR: Unsupported value for number of " + "column addresses: %d.\n", num_col_addr); + printf("Replace the DIMM module with a supported DIMM.\n\n"); + hang(); + } + + /* + * enable the bank + */ + cr |= SDRAM_BXCR_SDBE; + + /*------------------------------------------------------------------ + | This next section is hardware dependent and must be programmed + | to match the hardware. + +-----------------------------------------------------------------*/ + if (dimm_num == 0) { + for (i = 0; i < num_banks; i++) { + mtdcr(memcfga, mem_b0cr + (i << 2)); + temp = mfdcr(memcfgd) & ~(SDRAM_BXCR_SDBA_MASK | + SDRAM_BXCR_SDSZ_MASK | + SDRAM_BXCR_SDAM_MASK | + SDRAM_BXCR_SDBE); + cr |= temp; + cr |= bank_base_addr & SDRAM_BXCR_SDBA_MASK; + mtdcr(memcfgd, cr); + bank_base_addr += bank_size_bytes; + } + } else { + for (i = 0; i < num_banks; i++) { + mtdcr(memcfga, mem_b2cr + (i << 2)); + temp = mfdcr(memcfgd) & ~(SDRAM_BXCR_SDBA_MASK | + SDRAM_BXCR_SDSZ_MASK | + SDRAM_BXCR_SDAM_MASK | + SDRAM_BXCR_SDBE); + cr |= temp; + cr |= bank_base_addr & SDRAM_BXCR_SDBA_MASK; + mtdcr(memcfgd, cr); + bank_base_addr += bank_size_bytes; + } + } } - } } - } - return(bank_base_addr); + return(bank_base_addr); } void program_ecc (unsigned long num_bytes) { - unsigned long bank_base_addr; - unsigned long current_address; - unsigned long end_address; - unsigned long address_increment; - unsigned long cfg0; - - /* - * get Memory Controller Options 0 data - */ - mfsdram(mem_cfg0, cfg0); - - /* - * reset the bank_base address - */ - bank_base_addr = CFG_SDRAM_BASE; - - if ((cfg0 & SDRAM_CFG0_MCHK_MASK) != SDRAM_CFG0_MCHK_NON) { - mtsdram(mem_cfg0, (cfg0 & ~SDRAM_CFG0_MCHK_MASK) | - SDRAM_CFG0_MCHK_GEN); - - if ((cfg0 & SDRAM_CFG0_DMWD_MASK) == SDRAM_CFG0_DMWD_32) { - address_increment = 4; - } - else { - address_increment = 8; - } + unsigned long bank_base_addr; + unsigned long current_address; + unsigned long end_address; + unsigned long address_increment; + unsigned long cfg0; - current_address = (unsigned long)(bank_base_addr); - end_address = (unsigned long)(bank_base_addr) + num_bytes; + /* + * get Memory Controller Options 0 data + */ + mfsdram(mem_cfg0, cfg0); - while (current_address < end_address) { - *((unsigned long*)current_address) = 0x00000000; - current_address += address_increment; - } + /* + * reset the bank_base address + */ + bank_base_addr = CFG_SDRAM_BASE; + + if ((cfg0 & SDRAM_CFG0_MCHK_MASK) != SDRAM_CFG0_MCHK_NON) { + mtsdram(mem_cfg0, (cfg0 & ~SDRAM_CFG0_MCHK_MASK) | + SDRAM_CFG0_MCHK_GEN); + + if ((cfg0 & SDRAM_CFG0_DMWD_MASK) == SDRAM_CFG0_DMWD_32) { + address_increment = 4; + } else { + address_increment = 8; + } + + current_address = (unsigned long)(bank_base_addr); + end_address = (unsigned long)(bank_base_addr) + num_bytes; - mtsdram(mem_cfg0, (cfg0 & ~SDRAM_CFG0_MCHK_MASK) | - SDRAM_CFG0_MCHK_CHK); - } + while (current_address < end_address) { + *((unsigned long*)current_address) = 0x00000000; + current_address += address_increment; + } + + mtsdram(mem_cfg0, (cfg0 & ~SDRAM_CFG0_MCHK_MASK) | + SDRAM_CFG0_MCHK_CHK); + } } #endif /* CONFIG_440 */ |