summaryrefslogtreecommitdiff
path: root/cpu/mpc8xx
diff options
context:
space:
mode:
Diffstat (limited to 'cpu/mpc8xx')
-rw-r--r--cpu/mpc8xx/fec.c688
1 files changed, 459 insertions, 229 deletions
diff --git a/cpu/mpc8xx/fec.c b/cpu/mpc8xx/fec.c
index 811ac79..b7603da 100644
--- a/cpu/mpc8xx/fec.c
+++ b/cpu/mpc8xx/fec.c
@@ -29,13 +29,71 @@
#undef ET_DEBUG
-#if (CONFIG_COMMANDS & CFG_CMD_NET) && defined(FEC_ENET)
+#if (CONFIG_COMMANDS & CFG_CMD_NET) && \
+ (defined(FEC_ENET) || defined(CONFIG_ETHER_ON_FEC1) || defined(CONFIG_ETHER_ON_FEC2))
-#ifdef CFG_DISCOVER_PHY
+/* compatibility test, if only FEC_ENET defined assume ETHER on FEC1 */
+#if defined(FEC_ENET) && !defined(CONFIG_ETHER_ON_FEC1) && !defined(CONFIG_ETHER_ON_FEC2)
+#define CONFIG_ETHER_ON_FEC1 1
+#endif
+
+/* define WANT_MII when MII support is required */
+#if defined(CFG_DISCOVER_PHY) || defined(CONFIG_FEC1_PHY) || defined(CONFIG_FEC2_PHY)
+#define WANT_MII
+#else
+#undef WANT_MII
+#endif
+
+#if defined(WANT_MII)
#include <miiphy.h>
-static void mii_discover_phy(void);
#endif
+#if defined(CONFIG_RMII) && !defined(WANT_MII)
+#error RMII support is unusable without a working PHY.
+#endif
+
+#ifdef CFG_DISCOVER_PHY
+static int mii_discover_phy(struct eth_device *dev);
+#endif
+
+static struct ether_fcc_info_s
+{
+ int ether_index;
+ int fecp_offset;
+ int bd_offset;
+ int phy_addr;
+ int actual_phy_addr;
+}
+ ether_fcc_info[] = {
+#if defined(CONFIG_ETHER_ON_FEC1)
+ {
+ 0,
+ offsetof(immap_t, im_cpm.cp_fec1),
+ CPM_FEC_BASE,
+#if defined(CONFIG_FEC1_PHY)
+ CONFIG_FEC1_PHY,
+#else
+ -1, /* discover */
+#endif
+ -1,
+
+ },
+#endif
+#if defined(CONFIG_ETHER_ON_FEC2)
+ {
+ 1,
+ offsetof(immap_t, im_cpm.cp_fec2),
+ CPM_FEC_BASE + 0x50,
+#if defined(CONFIG_FEC2_PHY)
+ CONFIG_FEC2_PHY,
+#else
+ -1,
+#endif
+ -1,
+ },
+#endif
+};
+
/* Ethernet Transmit and Receive Buffers */
#define DBUF_LENGTH 1520
@@ -47,8 +105,11 @@ static void mii_discover_phy(void);
#define PKT_MINBUF_SIZE 64
#define PKT_MAXBLR_SIZE 1520
-
-static char txbuf[DBUF_LENGTH];
+#ifdef __GNUC__
+static char txbuf[DBUF_LENGTH] __attribute__ ((aligned(8)));
+#else
+#error txbuf must be aligned.
+#endif
static uint rxIdx; /* index of the current RX buffer */
static uint txIdx; /* index of the current TX buffer */
@@ -74,28 +135,49 @@ static void fec_halt(struct eth_device* dev);
int fec_initialize(bd_t *bis)
{
struct eth_device* dev;
+ struct ether_fcc_info_s *efis;
+ int i;
- dev = (struct eth_device*) malloc(sizeof *dev);
- memset(dev, 0, sizeof *dev);
+ for (i = 0; i < sizeof(ether_fcc_info) / sizeof(ether_fcc_info[0]); i++) {
- sprintf(dev->name, "FEC ETHERNET");
- dev->iobase = 0;
- dev->priv = 0;
- dev->init = fec_init;
- dev->halt = fec_halt;
- dev->send = fec_send;
- dev->recv = fec_recv;
+ dev = malloc(sizeof(*dev));
+ if (dev == NULL)
+ hang();
+
+ memset(dev, 0, sizeof(*dev));
+
+ /* for FEC1 make sure that the name of the interface is the same
+ as the old one for compatibility reasons */
+ if (i == 0) {
+ sprintf (dev->name, "FEC ETHERNET");
+ } else {
+ sprintf (dev->name, "FEC%d ETHERNET",
+ ether_fcc_info[i].ether_index + 1);
+ }
- eth_register(dev);
+ efis = &ether_fcc_info[i];
+ /*
+ * reset actual phy addr
+ */
+ efis->actual_phy_addr = -1;
+
+ dev->priv = efis;
+ dev->init = fec_init;
+ dev->halt = fec_halt;
+ dev->send = fec_send;
+ dev->recv = fec_recv;
+
+ eth_register(dev);
+ }
return 1;
}
static int fec_send(struct eth_device* dev, volatile void *packet, int length)
{
int j, rc;
- volatile immap_t *immr = (immap_t *) CFG_IMMR;
- volatile fec_t *fecp = &(immr->im_cpm.cp_fec);
+ struct ether_fcc_info_s *efis = dev->priv;
+ volatile fec_t *fecp = (volatile fec_t *)(CFG_IMMR + efis->fecp_offset);
/* section 16.9.23.3
* Wait for ready
@@ -142,50 +224,66 @@ static int fec_send(struct eth_device* dev, volatile void *packet, int length)
return rc;
}
-static int fec_recv(struct eth_device* dev)
+static int fec_recv (struct eth_device *dev)
{
+ struct ether_fcc_info_s *efis = dev->priv;
+ volatile fec_t *fecp =
+ (volatile fec_t *) (CFG_IMMR + efis->fecp_offset);
int length;
- volatile immap_t *immr = (immap_t *) CFG_IMMR;
- volatile fec_t *fecp = &(immr->im_cpm.cp_fec);
- for (;;) {
- /* section 16.9.23.2 */
- if (rtx->rxbd[rxIdx].cbd_sc & BD_ENET_RX_EMPTY) {
- length = -1;
- break; /* nothing received - leave for() loop */
- }
+ for (;;) {
+ /* section 16.9.23.2 */
+ if (rtx->rxbd[rxIdx].cbd_sc & BD_ENET_RX_EMPTY) {
+ length = -1;
+ break; /* nothing received - leave for() loop */
+ }
- length = rtx->rxbd[rxIdx].cbd_datlen;
+ length = rtx->rxbd[rxIdx].cbd_datlen;
- if (rtx->rxbd[rxIdx].cbd_sc & 0x003f) {
+ if (rtx->rxbd[rxIdx].cbd_sc & 0x003f) {
#ifdef ET_DEBUG
- printf("%s[%d] err: %x\n",
- __FUNCTION__,__LINE__,rtx->rxbd[rxIdx].cbd_sc);
+ printf ("%s[%d] err: %x\n",
+ __FUNCTION__, __LINE__,
+ rtx->rxbd[rxIdx].cbd_sc);
#endif
- } else {
- /* Pass the packet up to the protocol layers. */
- NetReceive(NetRxPackets[rxIdx], length - 4);
- }
+ } else {
+ volatile uchar *rx = NetRxPackets[rxIdx];
- /* Give the buffer back to the FEC. */
- rtx->rxbd[rxIdx].cbd_datlen = 0;
+ length -= 4;
- /* wrap around buffer index when necessary */
- if ((rxIdx + 1) >= PKTBUFSRX) {
- rtx->rxbd[PKTBUFSRX - 1].cbd_sc = (BD_ENET_RX_WRAP | BD_ENET_RX_EMPTY);
- rxIdx = 0;
- } else {
- rtx->rxbd[rxIdx].cbd_sc = BD_ENET_RX_EMPTY;
- rxIdx++;
- }
+#if (CONFIG_COMMANDS & CFG_CMD_CDP)
+ if ((rx[0] & 1) != 0
+ && memcmp ((uchar *) rx, NetBcastAddr, 6) != 0
+ && memcmp ((uchar *) rx, NetCDPAddr, 6) != 0)
+ rx = NULL;
+#endif
+ /*
+ * Pass the packet up to the protocol layers.
+ */
+ if (rx != NULL)
+ NetReceive (rx, length);
+ }
- __asm__ ("eieio");
+ /* Give the buffer back to the FEC. */
+ rtx->rxbd[rxIdx].cbd_datlen = 0;
+
+ /* wrap around buffer index when necessary */
+ if ((rxIdx + 1) >= PKTBUFSRX) {
+ rtx->rxbd[PKTBUFSRX - 1].cbd_sc =
+ (BD_ENET_RX_WRAP | BD_ENET_RX_EMPTY);
+ rxIdx = 0;
+ } else {
+ rtx->rxbd[rxIdx].cbd_sc = BD_ENET_RX_EMPTY;
+ rxIdx++;
+ }
+
+ __asm__ ("eieio");
- /* Try to fill Buffer Descriptors */
- fecp->fec_r_des_active = 0x01000000; /* Descriptor polling active */
- }
+ /* Try to fill Buffer Descriptors */
+ fecp->fec_r_des_active = 0x01000000; /* Descriptor polling active */
+ }
- return length;
+ return length;
}
/**************************************************************
@@ -210,34 +308,250 @@ static int fec_recv(struct eth_device* dev)
#define FEC_RESET_DELAY 50
-static int fec_init(struct eth_device* dev, bd_t * bd)
+#if defined(CONFIG_RMII)
+
+static inline void fec_10Mbps(struct eth_device *dev)
{
+ struct ether_fcc_info_s *efis = dev->priv;
+ int fecidx = efis->ether_index;
+ uint mask = (fecidx == 0) ? 0x0000010 : 0x0000008;
- int i;
+ if ((unsigned int)fecidx >= 2)
+ hang();
+
+ ((volatile immap_t *)CFG_IMMR)->im_cpm.cp_cptr |= mask;
+}
+
+static inline void fec_100Mbps(struct eth_device *dev)
+{
+ struct ether_fcc_info_s *efis = dev->priv;
+ int fecidx = efis->ether_index;
+ uint mask = (fecidx == 0) ? 0x0000010 : 0x0000008;
+
+ if ((unsigned int)fecidx >= 2)
+ hang();
+
+ ((volatile immap_t *)CFG_IMMR)->im_cpm.cp_cptr &= ~mask;
+}
+
+#endif
+
+static inline void fec_full_duplex(struct eth_device *dev)
+{
+ struct ether_fcc_info_s *efis = dev->priv;
+ volatile fec_t *fecp = (volatile fec_t *)(CFG_IMMR + efis->fecp_offset);
+
+ fecp->fec_r_cntrl &= ~FEC_RCNTRL_DRT;
+ fecp->fec_x_cntrl |= FEC_TCNTRL_FDEN; /* FD enable */
+}
+
+static inline void fec_half_duplex(struct eth_device *dev)
+{
+ struct ether_fcc_info_s *efis = dev->priv;
+ volatile fec_t *fecp = (volatile fec_t *)(CFG_IMMR + efis->fecp_offset);
+
+ fecp->fec_r_cntrl |= FEC_RCNTRL_DRT;
+ fecp->fec_x_cntrl &= ~FEC_TCNTRL_FDEN; /* FD disable */
+}
+
+static void fec_pin_init(int fecidx)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+ bd_t *bd = gd->bd;
volatile immap_t *immr = (immap_t *) CFG_IMMR;
- volatile fec_t *fecp = &(immr->im_cpm.cp_fec);
+ volatile fec_t *fecp;
-#if defined(CONFIG_FADS) /* FADS family uses FPGA (BCSR) to control PHYs */
-#if defined(CONFIG_DUET_ADS)
- *(vu_char *)BCSR5 &= ~(BCSR5_MII1_EN | BCSR5_MII1_RST);
-#else
- /* configure FADS for fast (FEC) ethernet, half-duplex */
- /* The LXT970 needs about 50ms to recover from reset, so
- * wait for it by discovering the PHY before leaving eth_init().
+ /*
+ * only two FECs please
*/
- {
- volatile uint *bcsr4 = (volatile uint *) BCSR4;
- *bcsr4 = (*bcsr4 & ~(BCSR4_FETH_EN | BCSR4_FETHCFG1))
- | (BCSR4_FETHCFG0 | BCSR4_FETHFDE | BCSR4_FETHRST);
-
- /* reset the LXT970 PHY */
- *bcsr4 &= ~BCSR4_FETHRST;
- udelay (10);
- *bcsr4 |= BCSR4_FETHRST;
- udelay (10);
+ if ((unsigned int)fecidx >= 2)
+ hang();
+
+ if (fecidx == 0)
+ fecp = &immr->im_cpm.cp_fec1;
+ else
+ fecp = &immr->im_cpm.cp_fec2;
+
+ /*
+ * Set MII speed to 2.5 MHz or slightly below.
+ * * According to the MPC860T (Rev. D) Fast ethernet controller user
+ * * manual (6.2.14),
+ * * the MII management interface clock must be less than or equal
+ * * to 2.5 MHz.
+ * * This MDC frequency is equal to system clock / (2 * MII_SPEED).
+ * * Then MII_SPEED = system_clock / 2 * 2,5 Mhz.
+ */
+ fecp->fec_mii_speed = ((bd->bi_intfreq + 4999999) / 5000000) << 1;
+
+#if defined(CONFIG_DUET) && defined(WANT_MII)
+ /* use MDC for MII */
+ immr->im_ioport.iop_pdpar |= 0x0080;
+ immr->im_ioport.iop_pddir &= ~0x0080;
+#endif
+
+ if (fecidx == 0) {
+#if defined(CONFIG_ETHER_ON_FEC1)
+
+#if defined(CONFIG_DUET) /* MPC87x/88x have got 2 FECs and different pinout */
+
+#if !defined(CONFIG_RMII)
+
+ immr->im_ioport.iop_papar |= 0xf830;
+ immr->im_ioport.iop_padir |= 0x0830;
+ immr->im_ioport.iop_padir &= ~0xf000;
+
+ immr->im_cpm.cp_pbpar |= 0x00001001;
+ immr->im_cpm.cp_pbdir &= ~0x00001001;
+
+ immr->im_ioport.iop_pcpar |= 0x000c;
+ immr->im_ioport.iop_pcdir &= ~0x000c;
+
+ immr->im_cpm.cp_pepar |= 0x00000003;
+ immr->im_cpm.cp_pedir |= 0x00000003;
+ immr->im_cpm.cp_peso &= ~0x00000003;
+
+ immr->im_cpm.cp_cptr &= ~0x00000100;
+
+#else
+
+#if !defined(CONFIG_FEC1_PHY_NORXERR)
+ immr->im_ioport.iop_papar |= 0x1000;
+ immr->im_ioport.iop_padir &= ~0x1000;
+#endif
+ immr->im_ioport.iop_papar |= 0xe810;
+ immr->im_ioport.iop_padir |= 0x0810;
+ immr->im_ioport.iop_padir &= ~0xe000;
+
+ immr->im_cpm.cp_pbpar |= 0x00000001;
+ immr->im_cpm.cp_pbdir &= ~0x00000001;
+
+ immr->im_cpm.cp_cptr |= 0x00000100;
+ immr->im_cpm.cp_cptr &= ~0x00000050;
+
+#endif /* !CONFIG_RMII */
+
+#elif !defined(CONFIG_ICU862) && !defined(CONFIG_IAD210)
+ /*
+ * Configure all of port D for MII.
+ */
+ immr->im_ioport.iop_pdpar = 0x1fff;
+
+ /*
+ * Bits moved from Rev. D onward
+ */
+ if ((get_immr(0) & 0xffff) < 0x0501)
+ immr->im_ioport.iop_pddir = 0x1c58; /* Pre rev. D */
+ else
+ immr->im_ioport.iop_pddir = 0x1fff; /* Rev. D and later */
+#else
+ /*
+ * Configure port A for MII.
+ */
+
+#if defined(CONFIG_ICU862) && defined(CFG_DISCOVER_PHY)
+
+ /*
+ * On the ICU862 board the MII-MDC pin is routed to PD8 pin
+ * * of CPU, so for this board we need to configure Utopia and
+ * * enable PD8 to MII-MDC function
+ */
+ immr->im_ioport.iop_pdpar |= 0x4080;
+#endif
+
+ /*
+ * Has Utopia been configured?
+ */
+ if (immr->im_ioport.iop_pdpar & (0x8000 >> 1)) {
+ /*
+ * YES - Use MUXED mode for UTOPIA bus.
+ * This frees Port A for use by MII (see 862UM table 41-6).
+ */
+ immr->im_ioport.utmode &= ~0x80;
+ } else {
+ /*
+ * NO - set SPLIT mode for UTOPIA bus.
+ *
+ * This doesn't really effect UTOPIA (which isn't
+ * enabled anyway) but just tells the 862
+ * to use port A for MII (see 862UM table 41-6).
+ */
+ immr->im_ioport.utmode |= 0x80;
+ }
+#endif /* !defined(CONFIG_ICU862) */
+
+#endif /* CONFIG_ETHER_ON_FEC1 */
+ } else if (fecidx == 1) {
+
+#if defined(CONFIG_ETHER_ON_FEC2)
+
+#if defined(CONFIG_DUET) /* MPC87x/88x have got 2 FECs and different pinout */
+
+#if !defined(CONFIG_RMII)
+
+#warning this configuration is not tested; please report if it works
+ immr->im_cpm.cp_pepar |= 0x0003fffc;
+ immr->im_cpm.cp_pedir |= 0x0003fffc;
+ immr->im_cpm.cp_peso &= ~0x000087fc;
+ immr->im_cpm.cp_peso |= 0x00037800;
+
+ immr->im_cpm.cp_cptr &= ~0x00000080;
+#else
+
+#if !defined(CONFIG_FEC2_PHY_NORXERR)
+ immr->im_cpm.cp_pepar |= 0x00000010;
+ immr->im_cpm.cp_pedir |= 0x00000010;
+ immr->im_cpm.cp_peso &= ~0x00000010;
+#endif
+ immr->im_cpm.cp_pepar |= 0x00039620;
+ immr->im_cpm.cp_pedir |= 0x00039620;
+ immr->im_cpm.cp_peso |= 0x00031000;
+ immr->im_cpm.cp_peso &= ~0x00008620;
+
+ immr->im_cpm.cp_cptr |= 0x00000080;
+ immr->im_cpm.cp_cptr &= ~0x00000028;
+#endif /* CONFIG_RMII */
+
+#endif /* CONFIG_DUET */
+
+#endif /* CONFIG_ETHER_ON_FEC2 */
+
}
+}
+
+static int fec_init (struct eth_device *dev, bd_t * bd)
+{
+ struct ether_fcc_info_s *efis = dev->priv;
+ volatile immap_t *immr = (immap_t *) CFG_IMMR;
+ volatile fec_t *fecp =
+ (volatile fec_t *) (CFG_IMMR + efis->fecp_offset);
+ int i;
+
+ if (efis->ether_index == 0) {
+#if defined(CONFIG_FADS) /* FADS family uses FPGA (BCSR) to control PHYs */
+#if defined(CONFIG_DUET_ADS)
+ *(vu_char *) BCSR5 &= ~(BCSR5_MII1_EN | BCSR5_MII1_RST);
+#else
+ /* configure FADS for fast (FEC) ethernet, half-duplex */
+ /* The LXT970 needs about 50ms to recover from reset, so
+ * wait for it by discovering the PHY before leaving eth_init().
+ */
+ {
+ volatile uint *bcsr4 = (volatile uint *) BCSR4;
+
+ *bcsr4 = (*bcsr4 & ~(BCSR4_FETH_EN | BCSR4_FETHCFG1))
+ | (BCSR4_FETHCFG0 | BCSR4_FETHFDE |
+ BCSR4_FETHRST);
+
+ /* reset the LXT970 PHY */
+ *bcsr4 &= ~BCSR4_FETHRST;
+ udelay (10);
+ *bcsr4 |= BCSR4_FETHRST;
+ udelay (10);
+ }
#endif /* CONFIG_DUET_ADS */
#endif /* CONFIG_FADS */
+ }
+
/* Whack a reset.
* A delay is required between a reset of the FEC block and
* initialization of other FEC registers because the reset takes
@@ -269,15 +583,22 @@ static int fec_init(struct eth_device* dev, bd_t * bd)
/* Set station address
*/
#define ea eth_get_dev()->enetaddr
- fecp->fec_addr_low = (ea[0] << 24) | (ea[1] << 16) |
- (ea[2] << 8) | (ea[3] ) ;
- fecp->fec_addr_high = (ea[4] << 8) | (ea[5] ) ;
+ fecp->fec_addr_low = (ea[0] << 24) | (ea[1] << 16) | (ea[2] << 8) | (ea[3]);
+ fecp->fec_addr_high = (ea[4] << 8) | (ea[5]);
#undef ea
+#if (CONFIG_COMMANDS & CFG_CMD_CDP)
+ /*
+ * Turn on multicast address hash table
+ */
+ fecp->fec_hash_table_high = 0xffffffff;
+ fecp->fec_hash_table_low = 0xffffffff;
+#else
/* Clear multicast address hash table
*/
fecp->fec_hash_table_high = 0;
- fecp->fec_hash_table_low = 0;
+ fecp->fec_hash_table_low = 0;
+#endif
/* Set maximum receive buffer size.
*/
@@ -295,9 +616,10 @@ static int fec_init(struct eth_device* dev, bd_t * bd)
if (!rtx) {
#ifdef CFG_ALLOC_DPRAM
- rtx = (RTXBD *) (immr->im_cpm.cp_dpmem + dpram_alloc_align(sizeof(RTXBD),8));
+ rtx = (RTXBD *) (immr->im_cpm.cp_dpmem +
+ dpram_alloc_align (sizeof (RTXBD), 8));
#else
- rtx = (RTXBD *) (immr->im_cpm.cp_dpmem + CPM_FEC_BASE);
+ rtx = (RTXBD *) (immr->im_cpm.cp_dpmem + CPM_FEC_BASE);
#endif
}
/*
@@ -306,8 +628,8 @@ static int fec_init(struct eth_device* dev, bd_t * bd)
* Empty, Wrap
*/
for (i = 0; i < PKTBUFSRX; i++) {
- rtx->rxbd[i].cbd_sc = BD_ENET_RX_EMPTY;
- rtx->rxbd[i].cbd_datlen = 0; /* Reset */
+ rtx->rxbd[i].cbd_sc = BD_ENET_RX_EMPTY;
+ rtx->rxbd[i].cbd_datlen = 0; /* Reset */
rtx->rxbd[i].cbd_bufaddr = (uint) NetRxPackets[i];
}
rtx->rxbd[PKTBUFSRX - 1].cbd_sc |= BD_ENET_RX_WRAP;
@@ -318,8 +640,8 @@ static int fec_init(struct eth_device* dev, bd_t * bd)
* Last, Tx CRC
*/
for (i = 0; i < TX_BUF_CNT; i++) {
- rtx->txbd[i].cbd_sc = BD_ENET_TX_LAST | BD_ENET_TX_TC;
- rtx->txbd[i].cbd_datlen = 0; /* Reset */
+ rtx->txbd[i].cbd_sc = BD_ENET_TX_LAST | BD_ENET_TX_TC;
+ rtx->txbd[i].cbd_datlen = 0; /* Reset */
rtx->txbd[i].cbd_bufaddr = (uint) (&txbuf[0]);
}
rtx->txbd[TX_BUF_CNT - 1].cbd_sc |= BD_ENET_TX_WRAP;
@@ -331,10 +653,10 @@ static int fec_init(struct eth_device* dev, bd_t * bd)
/* Enable MII mode
*/
-#if 0 /* Full duplex mode */
+#if 0 /* Full duplex mode */
fecp->fec_r_cntrl = FEC_RCNTRL_MII_MODE;
fecp->fec_x_cntrl = FEC_TCNTRL_FDEN;
-#else /* Half duplex mode */
+#else /* Half duplex mode */
fecp->fec_r_cntrl = FEC_RCNTRL_MII_MODE | FEC_RCNTRL_DRT;
fecp->fec_x_cntrl = 0;
#endif
@@ -343,86 +665,59 @@ static int fec_init(struct eth_device* dev, bd_t * bd)
*/
fecp->fec_fun_code = 0x78000000;
- /* Set MII speed to 2.5 MHz or slightly below.
- * According to the MPC860T (Rev. D) Fast ethernet controller user
- * manual (6.2.14),
- * the MII management interface clock must be less than or equal
- * to 2.5 MHz.
- * This MDC frequency is equal to system clock / (2 * MII_SPEED).
- * Then MII_SPEED = system_clock / 2 * 2,5 Mhz.
- */
- fecp->fec_mii_speed = ((bd->bi_intfreq + 4999999) / 5000000) << 1;
-
-#if defined(CONFIG_DUET) /* MPC87x/88x have got 2 FECs and different pinout */
- immr->im_ioport.iop_papar |= 0xf830;
- immr->im_ioport.iop_padir |= 0x0830;
- immr->im_ioport.iop_padir &= ~0xf000;
- immr->im_cpm.cp_pbpar |= 0x00001001;
- immr->im_cpm.cp_pbdir &= ~0x00001001;
- immr->im_ioport.iop_pcpar |= 0x000c;
- immr->im_ioport.iop_pcdir &= ~0x000c;
- immr->im_ioport.iop_pdpar |= 0x0080;
- immr->im_ioport.iop_pddir &= ~0x0080;
- immr->im_cpm.cp_pepar |= 0x00000003;
- immr->im_cpm.cp_pedir |= 0x00000003;
- immr->im_cpm.cp_peso &= ~0x00000003;
-#elif !defined(CONFIG_ICU862) && !defined(CONFIG_IAD210)
- /* Configure all of port D for MII.
+ /*
+ * Setup the pin configuration of the FEC
*/
- immr->im_ioport.iop_pdpar = 0x1fff;
-
- /* Bits moved from Rev. D onward */
- if ((get_immr (0) & 0xffff) < 0x0501) {
- immr->im_ioport.iop_pddir = 0x1c58; /* Pre rev. D */
- } else {
- immr->im_ioport.iop_pddir = 0x1fff; /* Rev. D and later */
- }
-#else
- /* Configure port A for MII.
- */
+ fec_pin_init (efis->ether_index);
-#if defined(CONFIG_ICU862) && defined(CFG_DISCOVER_PHY)
+ rxIdx = 0;
+ txIdx = 0;
- /* On the ICU862 board the MII-MDC pin is routed to PD8 pin
- * of CPU, so for this board we need to configure Utopia and
- * enable PD8 to MII-MDC function */
- immr->im_ioport.iop_pdpar |= 0x4080;
-#endif
+ /*
+ * Now enable the transmit and receive processing
+ */
+ fecp->fec_ecntrl = FEC_ECNTRL_PINMUX | FEC_ECNTRL_ETHER_EN;
- /* Has Utopia been configured? */
- if (immr->im_ioport.iop_pdpar & (0x8000 >> 1)) {
+ if (efis->phy_addr == -1) {
+#ifdef CFG_DISCOVER_PHY
/*
- * YES - Use MUXED mode for UTOPIA bus.
- * This frees Port A for use by MII (see 862UM table 41-6).
+ * wait for the PHY to wake up after reset
*/
- immr->im_ioport.utmode &= ~0x80;
+ efis->actual_phy_addr = mii_discover_phy (dev);
+#else
+ efis->actual_phy_addr = -1;
+#endif
+ if (efis->actual_phy_addr == -1) {
+ printf ("Unable to discover phy!\n");
+ return 0;
+ }
} else {
- /*
- * NO - set SPLIT mode for UTOPIA bus.
- *
- * This doesn't really effect UTOPIA (which isn't
- * enabled anyway) but just tells the 862
- * to use port A for MII (see 862UM table 41-6).
- */
- immr->im_ioport.utmode |= 0x80;
+ efis->actual_phy_addr = efis->phy_addr;
}
-#endif /* !defined(CONFIG_ICU862) */
-
- rxIdx = 0;
- txIdx = 0;
-
- /* Now enable the transmit and receive processing
+#if defined(CONFIG_MII) && defined(CONFIG_RMII)
+ /*
+ * adapt the RMII speed to the speed of the phy
*/
- fecp->fec_ecntrl = FEC_ECNTRL_PINMUX | FEC_ECNTRL_ETHER_EN;
+ if (miiphy_speed (efis->actual_phy_addr) == _100BASET) {
+ fec_100Mbps (dev);
+ } else {
+ fec_10Mbps (dev);
+ }
+#endif
-#ifdef CFG_DISCOVER_PHY
- /* wait for the PHY to wake up after reset
+#if defined(CONFIG_MII)
+ /*
+ * adapt to the half/full speed settings
*/
- mii_discover_phy();
+ if (miiphy_duplex (efis->actual_phy_addr) == FULL) {
+ fec_full_duplex (dev);
+ } else {
+ fec_half_duplex (dev);
+ }
#endif
/* And last, try to fill Rx Buffer Descriptors */
- fecp->fec_r_des_active = 0x01000000; /* Descriptor polling active */
+ fecp->fec_r_des_active = 0x01000000; /* Descriptor polling active */
return 1;
}
@@ -431,23 +726,20 @@ static int fec_init(struct eth_device* dev, bd_t * bd)
static void fec_halt(struct eth_device* dev)
{
#if 0
- volatile immap_t *immr = (immap_t *)CFG_IMMR;
- immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
+ volatile immap_t *immr = (immap_t *)CFG_IMMR;
+ immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
#endif
}
#if 0
void restart(void)
{
- volatile immap_t *immr = (immap_t *)CFG_IMMR;
- immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrl |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
+ volatile immap_t *immr = (immap_t *)CFG_IMMR;
+ immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrl |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
}
#endif
-#if defined(CFG_DISCOVER_PHY) || (CONFIG_COMMANDS & CFG_CMD_MII)
-
-static int phyaddr = -1; /* didn't find a PHY yet */
-static uint phytype;
+#if defined(CFG_DISCOVER_PHY) || defined(CONFIG_MII) || (CONFIG_COMMANDS & CFG_CMD_MII)
/* Make MII read/write commands for the FEC.
*/
@@ -508,12 +800,13 @@ mii_send(uint mii_cmd)
#endif /* CFG_DISCOVER_PHY || (CONFIG_COMMANDS & CFG_CMD_MII) */
#if defined(CFG_DISCOVER_PHY)
-static void
-mii_discover_phy(void)
+static int mii_discover_phy(struct eth_device *dev)
{
#define MAX_PHY_PASSES 11
uint phyno;
int pass;
+ uint phytype;
+ int phyaddr;
phyaddr = -1; /* didn't find a PHY yet */
for (pass = 1; pass <= MAX_PHY_PASSES && phyaddr < 0; ++pass) {
@@ -571,10 +864,11 @@ mii_discover_phy(void)
if (phyaddr < 0) {
printf("No PHY device found.\n");
}
+ return phyaddr;
}
#endif /* CFG_DISCOVER_PHY */
-#if (CONFIG_COMMANDS & CFG_CMD_MII) && !defined(CONFIG_BITBANGMII)
+#if (defined(CONFIG_MII) || (CONFIG_COMMANDS & CFG_CMD_MII)) && !defined(CONFIG_BITBANGMII)
static int mii_init_done = 0;
@@ -585,17 +879,16 @@ static int mii_init_done = 0;
*/
void mii_init (void)
{
- DECLARE_GLOBAL_DATA_PTR;
- bd_t *bd = gd->bd;
-
volatile immap_t *immr = (immap_t *) CFG_IMMR;
volatile fec_t *fecp = &(immr->im_cpm.cp_fec);
- int i;
+ int i, j;
if (mii_init_done != 0) {
return;
}
+ for (j = 0; j < sizeof(ether_fcc_info) / sizeof(ether_fcc_info[0]); j++) {
+
/* Whack a reset.
* A delay is required between a reset of the FEC block and
* initialization of other FEC registers because the reset takes
@@ -623,76 +916,18 @@ void mii_init (void)
*/
fecp->fec_ievent = 0xffc0;
- /* Set MII speed to 2.5 MHz or slightly below.
- * According to the MPC860T (Rev. D) Fast ethernet controller user
- * manual (6.2.14),
- * the MII management interface clock must be less than or equal
- * to 2.5 MHz.
- * This MDC frequency is equal to system clock / (2 * MII_SPEED).
- * Then MII_SPEED = system_clock / 2 * 2,5 Mhz.
- */
- fecp->fec_mii_speed = ((bd->bi_intfreq + 4999999) / 5000000) << 1;
-
-#if defined(CONFIG_DUET) /* MPC87x/88x have got 2 FECs and different pinout */
- immr->im_ioport.iop_papar |= 0xf830;
- immr->im_ioport.iop_padir |= 0x0830;
- immr->im_ioport.iop_padir &= ~0xf000;
- immr->im_cpm.cp_pbpar |= 0x00001001;
- immr->im_cpm.cp_pbdir &= ~0x00001001;
- immr->im_ioport.iop_pcpar |= 0x000c;
- immr->im_ioport.iop_pcdir &= ~0x000c;
- immr->im_ioport.iop_pdpar |= 0x0080;
- immr->im_ioport.iop_pddir &= ~0x0080;
- immr->im_cpm.cp_pepar |= 0x00000003;
- immr->im_cpm.cp_pedir |= 0x00000003;
- immr->im_cpm.cp_peso &= ~0x00000003;
-#elif !defined(CONFIG_ICU862) && !defined(CONFIG_IAD210)
- /* Configure all of port D for MII.
- */
- immr->im_ioport.iop_pdpar = 0x1fff;
-
- /* Bits moved from Rev. D onward */
- if ((get_immr (0) & 0xffff) < 0x0501) {
- immr->im_ioport.iop_pddir = 0x1c58; /* Pre rev. D */
- } else {
- immr->im_ioport.iop_pddir = 0x1fff; /* Rev. D and later */
- }
-#else
- /* Configure port A for MII.
+ /* Setup the pin configuration of the FEC(s)
*/
+ fec_pin_init(ether_fcc_info[i].ether_index);
-#if defined(CONFIG_ICU862)
-
- /* On the ICU862 board the MII-MDC pin is routed to PD8 pin
- * of CPU, so for this board we need to configure Utopia and
- * enable PD8 to MII-MDC function */
- immr->im_ioport.iop_pdpar |= 0x4080;
-#endif
-
- /* Has Utopia been configured? */
- if (immr->im_ioport.iop_pdpar & (0x8000 >> 1)) {
- /*
- * YES - Use MUXED mode for UTOPIA bus.
- * This frees Port A for use by MII (see 862UM table 41-6).
- */
- immr->im_ioport.utmode &= ~0x80;
- } else {
- /*
- * NO - set SPLIT mode for UTOPIA bus.
- *
- * This doesn't really effect UTOPIA (which isn't
- * enabled anyway) but just tells the 862
- * to use port A for MII (see 862UM table 41-6).
- */
- immr->im_ioport.utmode |= 0x80;
- }
-#endif /* !defined(CONFIG_ICU862) */
/* Now enable the transmit and receive processing
*/
fecp->fec_ecntrl = FEC_ECNTRL_PINMUX | FEC_ECNTRL_ETHER_EN;
+ }
mii_init_done = 1;
}
+
/*****************************************************************************
* Read and write a MII PHY register, routines used by MII Utilities
*
@@ -714,28 +949,23 @@ int miiphy_read(unsigned char addr, unsigned char reg, unsigned short *value)
rdreg = mii_send(mk_mii_read(addr, reg));
*value = rdreg;
-
#ifdef MII_DEBUG
printf ("0x%04x\n", *value);
#endif
-
return 0;
}
int miiphy_write(unsigned char addr, unsigned char reg, unsigned short value)
{
short rdreg; /* register working value */
-
#ifdef MII_DEBUG
printf ("miiphy_write(0x%x) @ 0x%x = ", reg, addr);
#endif
-
rdreg = mii_send(mk_mii_write(addr, reg, value));
#ifdef MII_DEBUG
printf ("0x%04x\n", value);
#endif
-
return 0;
}
#endif /* (CONFIG_COMMANDS & CFG_CMD_MII) && !defined(CONFIG_BITBANGMII)*/
generated by cgit v1.1 at 2024-12-17 01:48:25 +0000