diff options
Diffstat (limited to 'cpu/mcf52x2')
| -rw-r--r-- | cpu/mcf52x2/cpu_init.c | 349 |
1 files changed, 158 insertions, 191 deletions
diff --git a/cpu/mcf52x2/cpu_init.c b/cpu/mcf52x2/cpu_init.c index 7bb358e..18308c8 100644 --- a/cpu/mcf52x2/cpu_init.c +++ b/cpu/mcf52x2/cpu_init.c @@ -36,6 +36,71 @@ #include <watchdog.h> #include <asm/immap.h> +#if defined(CONFIG_CMD_NET) +#include <config.h> +#include <net.h> +#include <asm/fec.h> +#endif + +#ifndef CONFIG_M5272 +/* Only 5272 Flexbus chipselect is different from the rest */ +void init_fbcs(void) +{ + volatile fbcs_t *fbcs = (fbcs_t *) (MMAP_FBCS); + +#if (defined(CONFIG_SYS_CS0_BASE) && defined(CONFIG_SYS_CS0_MASK) \ + && defined(CONFIG_SYS_CS0_CTRL)) + fbcs->csar0 = CONFIG_SYS_CS0_BASE; + fbcs->cscr0 = CONFIG_SYS_CS0_CTRL; + fbcs->csmr0 = CONFIG_SYS_CS0_MASK; +#else +#warning "Chip Select 0 are not initialized/used" +#endif +#if (defined(CONFIG_SYS_CS1_BASE) && defined(CONFIG_SYS_CS1_MASK) \ + && defined(CONFIG_SYS_CS1_CTRL)) + fbcs->csar1 = CONFIG_SYS_CS1_BASE; + fbcs->cscr1 = CONFIG_SYS_CS1_CTRL; + fbcs->csmr1 = CONFIG_SYS_CS1_MASK; +#endif +#if (defined(CONFIG_SYS_CS2_BASE) && defined(CONFIG_SYS_CS2_MASK) \ + && defined(CONFIG_SYS_CS2_CTRL)) + fbcs->csar2 = CONFIG_SYS_CS2_BASE; + fbcs->cscr2 = CONFIG_SYS_CS2_CTRL; + fbcs->csmr2 = CONFIG_SYS_CS2_MASK; +#endif +#if (defined(CONFIG_SYS_CS3_BASE) && defined(CONFIG_SYS_CS3_MASK) \ + && defined(CONFIG_SYS_CS3_CTRL)) + fbcs->csar3 = CONFIG_SYS_CS3_BASE; + fbcs->cscr3 = CONFIG_SYS_CS3_CTRL; + fbcs->csmr3 = CONFIG_SYS_CS3_MASK; +#endif +#if (defined(CONFIG_SYS_CS4_BASE) && defined(CONFIG_SYS_CS4_MASK) \ + && defined(CONFIG_SYS_CS4_CTRL)) + fbcs->csar4 = CONFIG_SYS_CS4_BASE; + fbcs->cscr4 = CONFIG_SYS_CS4_CTRL; + fbcs->csmr4 = CONFIG_SYS_CS4_MASK; +#endif +#if (defined(CONFIG_SYS_CS5_BASE) && defined(CONFIG_SYS_CS5_MASK) \ + && defined(CONFIG_SYS_CS5_CTRL)) + fbcs->csar5 = CONFIG_SYS_CS5_BASE; + fbcs->cscr5 = CONFIG_SYS_CS5_CTRL; + fbcs->csmr5 = CONFIG_SYS_CS5_MASK; +#endif +#if (defined(CONFIG_SYS_CS6_BASE) && defined(CONFIG_SYS_CS6_MASK) \ + && defined(CONFIG_SYS_CS6_CTRL)) + fbcs->csar6 = CONFIG_SYS_CS6_BASE; + fbcs->cscr6 = CONFIG_SYS_CS6_CTRL; + fbcs->csmr6 = CONFIG_SYS_CS6_MASK; +#endif +#if (defined(CONFIG_SYS_CS7_BASE) && defined(CONFIG_SYS_CS7_MASK) \ + && defined(CONFIG_SYS_CS7_CTRL)) + fbcs->csar7 = CONFIG_SYS_CS7_BASE; + fbcs->cscr7 = CONFIG_SYS_CS7_CTRL; + fbcs->csmr7 = CONFIG_SYS_CS7_MASK; +#endif +} +#endif + #if defined(CONFIG_M5253) /* * Breath some life into the CPU... @@ -66,22 +131,14 @@ void cpu_init_f(void) mbar2_writeByte(MCFSIM_INTBASE, 0x40); /* Base interrupts at 64 */ mbar2_writeByte(MCFSIM_SPURVEC, 0x00); - /*mbar2_writeLong(MCFSIM_IDECONFIG1, 0x00000020); */ /* Enable a 1 cycle pre-drive cycle on CS1 */ - - /* - * Setup chip selects... - */ - - mbar_writeShort(MCFSIM_CSAR1, CONFIG_SYS_CSAR1); - mbar_writeShort(MCFSIM_CSCR1, CONFIG_SYS_CSCR1); - mbar_writeLong(MCFSIM_CSMR1, CONFIG_SYS_CSMR1); + /*mbar2_writeLong(MCFSIM_IDECONFIG1, 0x00000020); *//* Enable a 1 cycle pre-drive cycle on CS1 */ - mbar_writeShort(MCFSIM_CSAR0, CONFIG_SYS_CSAR0); - mbar_writeShort(MCFSIM_CSCR0, CONFIG_SYS_CSCR0); - mbar_writeLong(MCFSIM_CSMR0, CONFIG_SYS_CSMR0); + /* FlexBus Chipselect */ + init_fbcs(); #ifdef CONFIG_FSL_I2C - CONFIG_SYS_I2C_PINMUX_REG = CONFIG_SYS_I2C_PINMUX_REG & CONFIG_SYS_I2C_PINMUX_CLR; + CONFIG_SYS_I2C_PINMUX_REG = + CONFIG_SYS_I2C_PINMUX_REG & CONFIG_SYS_I2C_PINMUX_CLR; CONFIG_SYS_I2C_PINMUX_REG |= CONFIG_SYS_I2C_PINMUX_SET; #ifdef CONFIG_SYS_I2C2_OFFSET CONFIG_SYS_I2C2_PINMUX_REG &= CONFIG_SYS_I2C2_PINMUX_CLR; @@ -121,6 +178,9 @@ void cpu_init_f(void) mbar_writeShort(MCF_WTM_WCR, 0); #endif + /* FlexBus Chipselect */ + init_fbcs(); + /* Set clockspeed to 100MHz */ mbar_writeShort(MCF_FMPLL_SYNCR, MCF_FMPLL_SYNCR_MFD(0) | MCF_FMPLL_SYNCR_RFD(0)); @@ -153,6 +213,19 @@ void uart_port_conf(void) break; } } + +#if defined(CONFIG_CMD_NET) +int fecpin_setclear(struct eth_device *dev, int setclear) +{ + if (setclear) { + /* Enable Ethernet pins */ + mbar_writeByte(MCF_GPIO_PAR_FECI2C, CONFIG_SYS_FECI2C); + } else { + } + + return 0; +} +#endif /* CONFIG_CMD_NET */ #endif #if defined(CONFIG_M5272) @@ -255,6 +328,22 @@ void uart_port_conf(void) break; } } + +#if defined(CONFIG_CMD_NET) +int fecpin_setclear(struct eth_device *dev, int setclear) +{ + volatile gpio_t *gpio = (gpio_t *) MMAP_GPIO; + + if (setclear) { + gpio->gpio_pbcnt |= GPIO_PBCNT_E_MDC | GPIO_PBCNT_E_RXER | + GPIO_PBCNT_E_RXD1 | GPIO_PBCNT_E_RXD2 | + GPIO_PBCNT_E_RXD3 | GPIO_PBCNT_E_TXD1 | + GPIO_PBCNT_E_TXD2 | GPIO_PBCNT_E_TXD3; + } else { + } + return 0; +} +#endif /* CONFIG_CMD_NET */ #endif /* #if defined(CONFIG_M5272) */ #if defined(CONFIG_M5275) @@ -268,66 +357,20 @@ void uart_port_conf(void) */ void cpu_init_f(void) { - /* if we come from RAM we assume the CPU is + /* + * if we come from RAM we assume the CPU is * already initialized. */ #ifndef CONFIG_MONITOR_IS_IN_RAM - volatile wdog_t *wdog_reg = (wdog_t *)(MMAP_WDOG); - volatile gpio_t *gpio_reg = (gpio_t *)(MMAP_GPIO); - volatile csctrl_t *csctrl_reg = (csctrl_t *)(MMAP_FBCS); + volatile wdog_t *wdog_reg = (wdog_t *) (MMAP_WDOG); + volatile gpio_t *gpio_reg = (gpio_t *) (MMAP_GPIO); /* Kill watchdog so we can initialize the PLL */ wdog_reg->wcr = 0; - /* Memory Controller: */ - /* Flash */ - csctrl_reg->ar0 = CONFIG_SYS_AR0_PRELIM; - csctrl_reg->cr0 = CONFIG_SYS_CR0_PRELIM; - csctrl_reg->mr0 = CONFIG_SYS_MR0_PRELIM; - -#if (defined(CONFIG_SYS_AR1_PRELIM) && defined(CONFIG_SYS_CR1_PRELIM) && defined(CONFIG_SYS_MR1_PRELIM)) - csctrl_reg->ar1 = CONFIG_SYS_AR1_PRELIM; - csctrl_reg->cr1 = CONFIG_SYS_CR1_PRELIM; - csctrl_reg->mr1 = CONFIG_SYS_MR1_PRELIM; -#endif - -#if (defined(CONFIG_SYS_AR2_PRELIM) && defined(CONFIG_SYS_CR2_PRELIM) && defined(CONFIG_SYS_MR2_PRELIM)) - csctrl_reg->ar2 = CONFIG_SYS_AR2_PRELIM; - csctrl_reg->cr2 = CONFIG_SYS_CR2_PRELIM; - csctrl_reg->mr2 = CONFIG_SYS_MR2_PRELIM; -#endif - -#if (defined(CONFIG_SYS_AR3_PRELIM) && defined(CONFIG_SYS_CR3_PRELIM) && defined(CONFIG_SYS_MR3_PRELIM)) - csctrl_reg->ar3 = CONFIG_SYS_AR3_PRELIM; - csctrl_reg->cr3 = CONFIG_SYS_CR3_PRELIM; - csctrl_reg->mr3 = CONFIG_SYS_MR3_PRELIM; -#endif - -#if (defined(CONFIG_SYS_AR4_PRELIM) && defined(CONFIG_SYS_CR4_PRELIM) && defined(CONFIG_SYS_MR4_PRELIM)) - csctrl_reg->ar4 = CONFIG_SYS_AR4_PRELIM; - csctrl_reg->cr4 = CONFIG_SYS_CR4_PRELIM; - csctrl_reg->mr4 = CONFIG_SYS_MR4_PRELIM; -#endif - -#if (defined(CONFIG_SYS_AR5_PRELIM) && defined(CONFIG_SYS_CR5_PRELIM) && defined(CONFIG_SYS_MR5_PRELIM)) - csctrl_reg->ar5 = CONFIG_SYS_AR5_PRELIM; - csctrl_reg->cr5 = CONFIG_SYS_CR5_PRELIM; - csctrl_reg->mr5 = CONFIG_SYS_MR5_PRELIM; -#endif - -#if (defined(CONFIG_SYS_AR6_PRELIM) && defined(CONFIG_SYS_CR6_PRELIM) && defined(CONFIG_SYS_MR6_PRELIM)) - csctrl_reg->ar6 = CONFIG_SYS_AR6_PRELIM; - csctrl_reg->cr6 = CONFIG_SYS_CR6_PRELIM; - csctrl_reg->mr6 = CONFIG_SYS_MR6_PRELIM; -#endif - -#if (defined(CONFIG_SYS_AR7_PRELIM) && defined(CONFIG_SYS_CR7_PRELIM) && defined(CONFIG_SYS_MR7_PRELIM)) - csctrl_reg->ar7 = CONFIG_SYS_AR7_PRELIM; - csctrl_reg->cr7 = CONFIG_SYS_CR7_PRELIM; - csctrl_reg->mr7 = CONFIG_SYS_MR7_PRELIM; -#endif - + /* FlexBus Chipselect */ + init_fbcs(); #endif /* #ifndef CONFIG_MONITOR_IS_IN_RAM */ #ifdef CONFIG_FSL_I2C @@ -349,7 +392,7 @@ int cpu_init_r(void) void uart_port_conf(void) { - volatile gpio_t *gpio = (gpio_t *)MMAP_GPIO; + volatile gpio_t *gpio = (gpio_t *) MMAP_GPIO; /* Setup Ports: */ switch (CONFIG_SYS_UART_PORT) { @@ -364,6 +407,35 @@ void uart_port_conf(void) break; } } + +#if defined(CONFIG_CMD_NET) +int fecpin_setclear(struct eth_device *dev, int setclear) +{ + struct fec_info_s *info = (struct fec_info_s *) dev->priv; + volatile gpio_t *gpio = (gpio_t *)MMAP_GPIO; + + if (setclear) { + /* Enable Ethernet pins */ + if (info->iobase == CONFIG_SYS_FEC0_IOBASE) { + gpio->par_feci2c |= 0x0F00; + gpio->par_fec0hl |= 0xC0; + } else { + gpio->par_feci2c |= 0x00A0; + gpio->par_fec1hl |= 0xC0; + } + } else { + if (info->iobase == CONFIG_SYS_FEC0_IOBASE) { + gpio->par_feci2c &= ~0x0F00; + gpio->par_fec0hl &= ~0xC0; + } else { + gpio->par_feci2c &= ~0x00A0; + gpio->par_fec1hl &= ~0xC0; + } + } + + return 0; +} +#endif /* CONFIG_CMD_NET */ #endif /* #if defined(CONFIG_M5275) */ #if defined(CONFIG_M5282) @@ -384,7 +456,8 @@ void cpu_init_f(void) #ifndef CONFIG_MONITOR_IS_IN_RAM /* Set speed /PLL */ MCFCLOCK_SYNCR = - MCFCLOCK_SYNCR_MFD(CONFIG_SYS_MFD) | MCFCLOCK_SYNCR_RFD(CONFIG_SYS_RFD); + MCFCLOCK_SYNCR_MFD(CONFIG_SYS_MFD) | + MCFCLOCK_SYNCR_RFD(CONFIG_SYS_RFD); while (!(MCFCLOCK_SYNSR & MCFCLOCK_SYNSR_LOCK)) ; MCFGPIO_PBCDPAR = 0xc0; @@ -425,119 +498,8 @@ void cpu_init_f(void) MCFGPIO_DDRUA = CONFIG_SYS_DDRUA; #endif - /* This is probably a bad place to setup chip selects, but everyone - else is doing it! */ - -#if defined(CONFIG_SYS_CS0_BASE) & defined(CONFIG_SYS_CS0_SIZE) & \ - defined(CONFIG_SYS_CS0_WIDTH) & defined(CONFIG_SYS_CS0_WS) - - MCFCSM_CSAR0 = (CONFIG_SYS_CS0_BASE >> 16) & 0xFFFF; - -#if (CONFIG_SYS_CS0_WIDTH == 8) -#define CONFIG_SYS_CS0_PS MCFCSM_CSCR_PS_8 -#elif (CONFIG_SYS_CS0_WIDTH == 16) -#define CONFIG_SYS_CS0_PS MCFCSM_CSCR_PS_16 -#elif (CONFIG_SYS_CS0_WIDTH == 32) -#define CONFIG_SYS_CS0_PS MCFCSM_CSCR_PS_32 -#else -#error "CONFIG_SYS_CS0_WIDTH: Fault - wrong bus with for CS0" -#endif - MCFCSM_CSCR0 = MCFCSM_CSCR_WS(CONFIG_SYS_CS0_WS) - | CONFIG_SYS_CS0_PS | MCFCSM_CSCR_AA; - -#if (CONFIG_SYS_CS0_RO != 0) - MCFCSM_CSMR0 = MCFCSM_CSMR_BAM(CONFIG_SYS_CS0_SIZE - 1) - | MCFCSM_CSMR_WP | MCFCSM_CSMR_V; -#else - MCFCSM_CSMR0 = MCFCSM_CSMR_BAM(CONFIG_SYS_CS0_SIZE - 1) | MCFCSM_CSMR_V; -#endif -#else -#warning "Chip Select 0 are not initialized/used" -#endif - -#if defined(CONFIG_SYS_CS1_BASE) & defined(CONFIG_SYS_CS1_SIZE) & \ - defined(CONFIG_SYS_CS1_WIDTH) & defined(CONFIG_SYS_CS1_WS) - - MCFCSM_CSAR1 = (CONFIG_SYS_CS1_BASE >> 16) & 0xFFFF; - -#if (CONFIG_SYS_CS1_WIDTH == 8) -#define CONFIG_SYS_CS1_PS MCFCSM_CSCR_PS_8 -#elif (CONFIG_SYS_CS1_WIDTH == 16) -#define CONFIG_SYS_CS1_PS MCFCSM_CSCR_PS_16 -#elif (CONFIG_SYS_CS1_WIDTH == 32) -#define CONFIG_SYS_CS1_PS MCFCSM_CSCR_PS_32 -#else -#error "CONFIG_SYS_CS1_WIDTH: Fault - wrong bus with for CS1" -#endif - MCFCSM_CSCR1 = MCFCSM_CSCR_WS(CONFIG_SYS_CS1_WS) - | CONFIG_SYS_CS1_PS | MCFCSM_CSCR_AA; - -#if (CONFIG_SYS_CS1_RO != 0) - MCFCSM_CSMR1 = MCFCSM_CSMR_BAM(CONFIG_SYS_CS1_SIZE - 1) - | MCFCSM_CSMR_WP | MCFCSM_CSMR_V; -#else - MCFCSM_CSMR1 = MCFCSM_CSMR_BAM(CONFIG_SYS_CS1_SIZE - 1) - | MCFCSM_CSMR_V; -#endif -#else -#warning "Chip Select 1 are not initialized/used" -#endif - -#if defined(CONFIG_SYS_CS2_BASE) & defined(CONFIG_SYS_CS2_SIZE) & \ - defined(CONFIG_SYS_CS2_WIDTH) & defined(CONFIG_SYS_CS2_WS) - - MCFCSM_CSAR2 = (CONFIG_SYS_CS2_BASE >> 16) & 0xFFFF; - -#if (CONFIG_SYS_CS2_WIDTH == 8) -#define CONFIG_SYS_CS2_PS MCFCSM_CSCR_PS_8 -#elif (CONFIG_SYS_CS2_WIDTH == 16) -#define CONFIG_SYS_CS2_PS MCFCSM_CSCR_PS_16 -#elif (CONFIG_SYS_CS2_WIDTH == 32) -#define CONFIG_SYS_CS2_PS MCFCSM_CSCR_PS_32 -#else -#error "CONFIG_SYS_CS2_WIDTH: Fault - wrong bus with for CS2" -#endif - MCFCSM_CSCR2 = MCFCSM_CSCR_WS(CONFIG_SYS_CS2_WS) - | CONFIG_SYS_CS2_PS | MCFCSM_CSCR_AA; - -#if (CONFIG_SYS_CS2_RO != 0) - MCFCSM_CSMR2 = MCFCSM_CSMR_BAM(CONFIG_SYS_CS2_SIZE - 1) - | MCFCSM_CSMR_WP | MCFCSM_CSMR_V; -#else - MCFCSM_CSMR2 = MCFCSM_CSMR_BAM(CONFIG_SYS_CS2_SIZE - 1) - | MCFCSM_CSMR_V; -#endif -#else -#warning "Chip Select 2 are not initialized/used" -#endif - -#if defined(CONFIG_SYS_CS3_BASE) & defined(CONFIG_SYS_CS3_SIZE) & \ - defined(CONFIG_SYS_CS3_WIDTH) & defined(CONFIG_SYS_CS3_WS) - - MCFCSM_CSAR3 = (CONFIG_SYS_CS3_BASE >> 16) & 0xFFFF; - -#if (CONFIG_SYS_CS3_WIDTH == 8) -#define CONFIG_SYS_CS3_PS MCFCSM_CSCR_PS_8 -#elif (CONFIG_SYS_CS3_WIDTH == 16) -#define CONFIG_SYS_CS3_PS MCFCSM_CSCR_PS_16 -#elif (CONFIG_SYS_CS3_WIDTH == 32) -#define CONFIG_SYS_CS3_PS MCFCSM_CSCR_PS_32 -#else -#error "CONFIG_SYS_CS3_WIDTH: Fault - wrong bus with for CS1" -#endif - MCFCSM_CSCR3 = MCFCSM_CSCR_WS(CONFIG_SYS_CS3_WS) - | CONFIG_SYS_CS3_PS | MCFCSM_CSCR_AA; - -#if (CONFIG_SYS_CS3_RO != 0) - MCFCSM_CSMR3 = MCFCSM_CSMR_BAM(CONFIG_SYS_CS3_SIZE - 1) - | MCFCSM_CSMR_WP | MCFCSM_CSMR_V; -#else - MCFCSM_CSMR3 = MCFCSM_CSMR_BAM(CONFIG_SYS_CS3_SIZE - 1) - | MCFCSM_CSMR_V; -#endif -#else -#warning "Chip Select 3 are not initialized/used" -#endif + /* FlexBus Chipselect */ + init_fbcs(); #endif /* CONFIG_MONITOR_IS_IN_RAM */ @@ -571,6 +533,20 @@ void uart_port_conf(void) break; } } + +#if defined(CONFIG_CMD_NET) +int fecpin_setclear(struct eth_device *dev, int setclear) +{ + if (setclear) { + MCFGPIO_PASPAR |= 0x0F00; + MCFGPIO_PEHLPAR = CONFIG_SYS_PEHLPAR; + } else { + MCFGPIO_PASPAR &= 0xF0FF; + MCFGPIO_PEHLPAR &= ~CONFIG_SYS_PEHLPAR; + } + return 0; +} +#endif /* CONFIG_CMD_NET */ #endif #if defined(CONFIG_M5249) @@ -632,17 +608,8 @@ void cpu_init_f(void) mbar2_writeLong(MCFSIM_IDECONFIG1, 0x00000020); mbar2_writeLong(MCFSIM_IDECONFIG2, 0x00000000); - /* - * Setup chip selects... - */ - - mbar_writeShort(MCFSIM_CSAR1, CONFIG_SYS_CSAR1); - mbar_writeShort(MCFSIM_CSCR1, CONFIG_SYS_CSCR1); - mbar_writeLong(MCFSIM_CSMR1, CONFIG_SYS_CSMR1); - - mbar_writeShort(MCFSIM_CSAR0, CONFIG_SYS_CSAR0); - mbar_writeShort(MCFSIM_CSCR0, CONFIG_SYS_CSCR0); - mbar_writeLong(MCFSIM_CSMR0, CONFIG_SYS_CSMR0); + /* FlexBus Chipselect */ + init_fbcs(); /* enable instruction cache now */ icache_enable(); |