diff options
Diffstat (limited to 'cpu/blackfin/serial.h')
| -rw-r--r-- | cpu/blackfin/serial.h | 275 |
1 files changed, 275 insertions, 0 deletions
diff --git a/cpu/blackfin/serial.h b/cpu/blackfin/serial.h new file mode 100644 index 0000000..1f0f4b4 --- /dev/null +++ b/cpu/blackfin/serial.h @@ -0,0 +1,275 @@ +/* + * serial.h - common serial defines for early debug and serial driver. + * any functions defined here must be always_inline since + * initcode cannot have function calls. + * + * Copyright (c) 2004-2007 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#ifndef __BFIN_CPU_SERIAL_H__ +#define __BFIN_CPU_SERIAL_H__ + +#include <asm/blackfin.h> +#include <asm/mach-common/bits/uart.h> + +#ifdef CONFIG_DEBUG_EARLY_SERIAL +# define BFIN_DEBUG_EARLY_SERIAL 1 +#else +# define BFIN_DEBUG_EARLY_SERIAL 0 +#endif + +#define LOB(x) ((x) & 0xFF) +#define HIB(x) (((x) >> 8) & 0xFF) + +#ifndef UART_LSR +# if (CONFIG_UART_CONSOLE == 3) +# define pUART_DLH pUART3_DLH +# define pUART_DLL pUART3_DLL +# define pUART_GCTL pUART3_GCTL +# define pUART_IER pUART3_IER +# define pUART_IERC pUART3_IER_CLEAR +# define pUART_LCR pUART3_LCR +# define pUART_LSR pUART3_LSR +# define pUART_RBR pUART3_RBR +# define pUART_THR pUART3_THR +# define UART_THR UART3_THR +# define UART_LSR UART3_LSR +# elif (CONFIG_UART_CONSOLE == 2) +# define pUART_DLH pUART2_DLH +# define pUART_DLL pUART2_DLL +# define pUART_GCTL pUART2_GCTL +# define pUART_IER pUART2_IER +# define pUART_IERC pUART2_IER_CLEAR +# define pUART_LCR pUART2_LCR +# define pUART_LSR pUART2_LSR +# define pUART_RBR pUART2_RBR +# define pUART_THR pUART2_THR +# define UART_THR UART2_THR +# define UART_LSR UART2_LSR +# elif (CONFIG_UART_CONSOLE == 1) +# define pUART_DLH pUART1_DLH +# define pUART_DLL pUART1_DLL +# define pUART_GCTL pUART1_GCTL +# define pUART_IER pUART1_IER +# define pUART_IERC pUART1_IER_CLEAR +# define pUART_LCR pUART1_LCR +# define pUART_LSR pUART1_LSR +# define pUART_RBR pUART1_RBR +# define pUART_THR pUART1_THR +# define UART_THR UART1_THR +# define UART_LSR UART1_LSR +# elif (CONFIG_UART_CONSOLE == 0) +# define pUART_DLH pUART0_DLH +# define pUART_DLL pUART0_DLL +# define pUART_GCTL pUART0_GCTL +# define pUART_IER pUART0_IER +# define pUART_IERC pUART0_IER_CLEAR +# define pUART_LCR pUART0_LCR +# define pUART_LSR pUART0_LSR +# define pUART_RBR pUART0_RBR +# define pUART_THR pUART0_THR +# define UART_THR UART0_THR +# define UART_LSR UART0_LSR +# endif +#endif + +#ifndef __ASSEMBLY__ + +/* We cannot use get_sclk() in initcode as it is defined elsewhere. */ +#ifdef BFIN_IN_INITCODE +# define get_sclk() (CONFIG_CLKIN_HZ * CONFIG_VCO_MULT / CONFIG_SCLK_DIV) +#endif + +#ifdef __ADSPBF54x__ +# define ACCESS_LATCH() +# define ACCESS_PORT_IER() +# define CLEAR_IER() (*pUART_IERC = 0) +#else +# define ACCESS_LATCH() (*pUART_LCR |= DLAB) +# define ACCESS_PORT_IER() (*pUART_LCR &= ~DLAB) +# define CLEAR_IER() (*pUART_IER = 0) +#endif + +__attribute__((always_inline)) +static inline void serial_do_portmux(void) +{ +#ifdef __ADSPBF52x__ +# define DO_MUX(port, mux, tx, rx) \ + bfin_write_PORT##port##_MUX((bfin_read_PORT##port##_MUX() & ~PORT_x_MUX_##mux##_MASK) | PORT_x_MUX_##mux##_FUNC_3); \ + bfin_write_PORT##port##_FER(bfin_read_PORT##port##_FER() | P##port##tx | P##port##rx); + switch (CONFIG_UART_CONSOLE) { + case 0: DO_MUX(G, 2, 7, 8); break; /* Port G; mux 2; PG2 and PG8 */ + case 1: DO_MUX(F, 5, 14, 15); break; /* Port F; mux 5; PF14 and PF15 */ + } + SSYNC(); +#elif defined(__ADSPBF537__) || defined(__ADSPBF536__) || defined(__ADSPBF534__) +# define DO_MUX(func, tx, rx) \ + bfin_write_PORT_MUX(bfin_read_PORT_MUX() & ~(func)); \ + bfin_write_PORTF_FER(bfin_read_PORTF_FER() | PF##tx | PF##rx); + switch (CONFIG_UART_CONSOLE) { + case 0: DO_MUX(PFDE, 0, 1); break; + case 1: DO_MUX(PFTE, 2, 3); break; + } + SSYNC(); +#elif defined(__ADSPBF54x__) +# define DO_MUX(port, tx, rx) \ + bfin_write_PORT##port##_MUX((bfin_read_PORT##port##_MUX() & ~(PORT_x_MUX_##tx##_MASK | PORT_x_MUX_##rx##_MASK)) | PORT_x_MUX_##tx##_FUNC_1 | PORT_x_MUX_##rx##_FUNC_1); \ + bfin_write_PORT##port##_FER(bfin_read_PORT##port##_FER() | P##port##tx | P##port##rx); + switch (CONFIG_UART_CONSOLE) { + case 0: DO_MUX(E, 7, 8); break; /* Port E; PE7 and PE8 */ + case 1: DO_MUX(H, 0, 1); break; /* Port H; PH0 and PH1 */ + case 2: DO_MUX(B, 4, 5); break; /* Port B; PB4 and PB5 */ + case 3: DO_MUX(B, 6, 7); break; /* Port B; PB6 and PB7 */ + } + SSYNC(); +#endif +} + +__attribute__((always_inline)) +static inline void serial_early_init(void) +{ + /* handle portmux crap on different Blackfins */ + serial_do_portmux(); + + /* Enable UART */ + *pUART_GCTL = UCEN; + + /* Set LCR to Word Lengh 8-bit word select */ + *pUART_LCR = WLS_8; + + SSYNC(); +} + +__attribute__((always_inline)) +static inline uint32_t serial_early_get_baud(void) +{ + /* If the UART isnt enabled, then we are booting an LDR + * from a non-UART source (so like flash) which means + * the baud rate here is meaningless. + */ + if ((*pUART_GCTL & UCEN) != UCEN) + return 0; + +#if (0) /* See comment for serial_reset_baud() in initcode.c */ + /* Set DLAB in LCR to Access DLL and DLH */ + ACCESS_LATCH(); + SSYNC(); + + uint8_t dll = *pUART_DLL; + uint8_t dlh = *pUART_DLH; + uint16_t divisor = (dlh << 8) | dll; + uint32_t baud = get_sclk() / (divisor * 16); + + /* Clear DLAB in LCR to Access THR RBR IER */ + ACCESS_PORT_IER(); + SSYNC(); + + return baud; +#else + return CONFIG_BAUDRATE; +#endif +} + +__attribute__((always_inline)) +static inline void serial_early_set_baud(uint32_t baud) +{ + /* Translate from baud into divisor in terms of SCLK. + * The +1 is to make sure we over sample just a little + * rather than under sample the incoming signals. + */ + uint16_t divisor = (get_sclk() / (baud * 16)) + 1; + + /* Set DLAB in LCR to Access DLL and DLH */ + ACCESS_LATCH(); + SSYNC(); + + /* Program the divisor to get the baud rate we want */ + *pUART_DLL = LOB(divisor); + *pUART_DLH = HIB(divisor); + SSYNC(); + + /* Clear DLAB in LCR to Access THR RBR IER */ + ACCESS_PORT_IER(); + SSYNC(); +} + +#ifndef BFIN_IN_INITCODE +__attribute__((always_inline)) +static inline void serial_early_puts(const char *s) +{ + if (BFIN_DEBUG_EARLY_SERIAL) { + serial_puts("Early: "); + serial_puts(s); + } +} +#endif + +#else + +.macro serial_early_init +#ifdef CONFIG_DEBUG_EARLY_SERIAL + call _serial_initialize; +#endif +.endm + +.macro serial_early_set_baud +#ifdef CONFIG_DEBUG_EARLY_SERIAL + R0.L = LO(CONFIG_BAUDRATE); + R0.H = HI(CONFIG_BAUDRATE); + call _serial_set_baud; +#endif +.endm + +/* Recursively expand calls to _serial_putc for every byte + * passed to us. Append a newline when we're all done. + */ +.macro _serial_early_putc byte:req morebytes:vararg +#ifdef CONFIG_DEBUG_EARLY_SERIAL + R0 = \byte; + call _serial_putc; +.ifnb \morebytes + _serial_early_putc \morebytes +.else +.if (\byte != '\n') + _serial_early_putc '\n' +.endif +.endif +#endif +.endm + +/* Wrapper around recurisve _serial_early_putc macro which + * simply prepends the string "Early: " + */ +.macro serial_early_putc byte:req morebytes:vararg +#ifdef CONFIG_DEBUG_EARLY_SERIAL + _serial_early_putc 'E', 'a', 'r', 'l', 'y', ':', ' ', \byte, \morebytes +#endif +.endm + +/* Since we embed the string right into our .text section, we need + * to find its address. We do this by getting our PC and adding 2 + * bytes (which is the length of the jump instruction). Then we + * pass this address to serial_puts(). + */ +#ifdef CONFIG_DEBUG_EARLY_SERIAL +# define serial_early_puts(str) \ + call _get_pc; \ + jump 1f; \ + .ascii "Early:"; \ + .ascii __FILE__; \ + .ascii ": "; \ + .ascii str; \ + .asciz "\n"; \ + .align 4; \ +1: \ + R0 += 2; \ + call _serial_puts; +#else +# define serial_early_puts(str) +#endif + +#endif + +#endif |