diff options
Diffstat (limited to 'cpu/blackfin/initcode.c')
| -rw-r--r-- | cpu/blackfin/initcode.c | 353 |
1 files changed, 353 insertions, 0 deletions
diff --git a/cpu/blackfin/initcode.c b/cpu/blackfin/initcode.c new file mode 100644 index 0000000..ffc8420 --- /dev/null +++ b/cpu/blackfin/initcode.c @@ -0,0 +1,353 @@ +/* + * initcode.c - Initialize the processor. This is usually entails things + * like external memory, voltage regulators, etc... Note that this file + * cannot make any function calls as it may be executed all by itself by + * the Blackfin's bootrom in LDR format. + * + * Copyright (c) 2004-2008 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#include <config.h> +#include <asm/blackfin.h> +#include <asm/mach-common/bits/bootrom.h> +#include <asm/mach-common/bits/ebiu.h> +#include <asm/mach-common/bits/pll.h> +#include <asm/mach-common/bits/uart.h> + +#define BFIN_IN_INITCODE +#include "serial.h" + +__attribute__((always_inline)) +static inline uint32_t serial_init(void) +{ +#ifdef __ADSPBF54x__ +# ifdef BFIN_BOOT_UART_USE_RTS +# define BFIN_UART_USE_RTS 1 +# else +# define BFIN_UART_USE_RTS 0 +# endif + if (BFIN_UART_USE_RTS && CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_UART) { + size_t i; + + /* force RTS rather than relying on auto RTS */ + bfin_write_UART1_MCR(bfin_read_UART1_MCR() | FCPOL); + + /* Wait for the line to clear up. We cannot rely on UART + * registers as none of them reflect the status of the RSR. + * Instead, we'll sleep for ~10 bit times at 9600 baud. + * We can precalc things here by assuming boot values for + * PLL rather than loading registers and calculating. + * baud = SCLK / (16 ^ (1 - EDBO) * Divisor) + * EDB0 = 0 + * Divisor = (SCLK / baud) / 16 + * SCLK = baud * 16 * Divisor + * SCLK = (0x14 * CONFIG_CLKIN_HZ) / 5 + * CCLK = (16 * Divisor * 5) * (9600 / 10) + * In reality, this will probably be just about 1 second delay, + * so assuming 9600 baud is OK (both as a very low and too high + * speed as this will buffer things enough). + */ +#define _NUMBITS (10) /* how many bits to delay */ +#define _LOWBAUD (9600) /* low baud rate */ +#define _SCLK ((0x14 * CONFIG_CLKIN_HZ) / 5) /* SCLK based on PLL */ +#define _DIVISOR ((_SCLK / _LOWBAUD) / 16) /* UART DLL/DLH */ +#define _NUMINS (3) /* how many instructions in loop */ +#define _CCLK (((16 * _DIVISOR * 5) * (_LOWBAUD / _NUMBITS)) / _NUMINS) + i = _CCLK; + while (i--) + asm volatile("" : : : "memory"); + } +#endif + + uint32_t old_baud = serial_early_get_baud(); + + if (BFIN_DEBUG_EARLY_SERIAL) { + serial_early_init(); + + /* If the UART is off, that means we need to program + * the baud rate ourselves initially. + */ + if (!old_baud) { + old_baud = CONFIG_BAUDRATE; + serial_early_set_baud(CONFIG_BAUDRATE); + } + } + + return old_baud; +} + +__attribute__((always_inline)) +static inline void serial_deinit(void) +{ +#ifdef __ADSPBF54x__ + if (BFIN_UART_USE_RTS && CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_UART) { + /* clear forced RTS rather than relying on auto RTS */ + bfin_write_UART1_MCR(bfin_read_UART1_MCR() & ~FCPOL); + } +#endif +} + +/* We need to reset the baud rate when we have early debug turned on + * or when we are booting over the UART. + * XXX: we should fix this to calc the old baud and restore it rather + * than hardcoding it via CONFIG_LDR_LOAD_BAUD ... but we have + * to figure out how to avoid the division in the baud calc ... + */ +__attribute__((always_inline)) +static inline void serial_reset_baud(uint32_t baud) +{ + if (!BFIN_DEBUG_EARLY_SERIAL && CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART) + return; + +#ifndef CONFIG_LDR_LOAD_BAUD +# define CONFIG_LDR_LOAD_BAUD 115200 +#endif + + if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS) + serial_early_set_baud(baud); + else if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_UART) + serial_early_set_baud(CONFIG_LDR_LOAD_BAUD); + else + serial_early_set_baud(CONFIG_BAUDRATE); +} + +__attribute__((always_inline)) +static inline void serial_putc(char c) +{ + if (!BFIN_DEBUG_EARLY_SERIAL) + return; + + if (c == '\n') + *pUART_THR = '\r'; + + *pUART_THR = c; + + while (!(*pUART_LSR & TEMT)) + continue; +} + + +/* Max SCLK can be 133MHz ... dividing that by 4 gives + * us a freq of 33MHz for SPI which should generally be + * slow enough for the slow reads the bootrom uses. + */ +#ifndef CONFIG_SPI_BAUD_INITBLOCK +# define CONFIG_SPI_BAUD_INITBLOCK 4 +#endif + +/* PLL_DIV defines */ +#ifndef CONFIG_PLL_DIV_VAL +# if (CONFIG_CCLK_DIV == 1) +# define CONFIG_CCLK_ACT_DIV CCLK_DIV1 +# elif (CONFIG_CCLK_DIV == 2) +# define CONFIG_CCLK_ACT_DIV CCLK_DIV2 +# elif (CONFIG_CCLK_DIV == 4) +# define CONFIG_CCLK_ACT_DIV CCLK_DIV4 +# elif (CONFIG_CCLK_DIV == 8) +# define CONFIG_CCLK_ACT_DIV CCLK_DIV8 +# else +# define CONFIG_CCLK_ACT_DIV CONFIG_CCLK_DIV_not_defined_properly +# endif +# define CONFIG_PLL_DIV_VAL (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV) +#endif + +#ifndef CONFIG_PLL_LOCKCNT_VAL +# define CONFIG_PLL_LOCKCNT_VAL 0x0300 +#endif + +#ifndef CONFIG_PLL_CTL_VAL +# define CONFIG_PLL_CTL_VAL (SPORT_HYST | (CONFIG_VCO_MULT << 9)) +#endif + +#ifndef CONFIG_EBIU_RSTCTL_VAL +# define CONFIG_EBIU_RSTCTL_VAL 0 /* only MDDRENABLE is useful */ +#endif + +#ifndef CONFIG_EBIU_MBSCTL_VAL +# define CONFIG_EBIU_MBSCTL_VAL 0 +#endif + +/* Make sure our voltage value is sane so we don't blow up! */ +#ifndef CONFIG_VR_CTL_VAL +# define BFIN_CCLK ((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT) / CONFIG_CCLK_DIV) +# if defined(__ADSPBF533__) || defined(__ADSPBF532__) || defined(__ADSPBF531__) +# define CCLK_VLEV_120 400000000 +# define CCLK_VLEV_125 533000000 +# elif defined(__ADSPBF537__) || defined(__ADSPBF536__) || defined(__ADSPBF534__) +# define CCLK_VLEV_120 401000000 +# define CCLK_VLEV_125 401000000 +# elif defined(__ADSPBF561__) +# define CCLK_VLEV_120 300000000 +# define CCLK_VLEV_125 501000000 +# endif +# if BFIN_CCLK < CCLK_VLEV_120 +# define CONFIG_VR_CTL_VLEV VLEV_120 +# elif BFIN_CCLK < CCLK_VLEV_125 +# define CONFIG_VR_CTL_VLEV VLEV_125 +# else +# define CONFIG_VR_CTL_VLEV VLEV_130 +# endif +# if defined(__ADSPBF52x__) /* TBD; use default */ +# undef CONFIG_VR_CTL_VLEV +# define CONFIG_VR_CTL_VLEV VLEV_110 +# elif defined(__ADSPBF54x__) /* TBD; use default */ +# undef CONFIG_VR_CTL_VLEV +# define CONFIG_VR_CTL_VLEV VLEV_120 +# endif + +# ifdef CONFIG_BFIN_MAC +# define CONFIG_VR_CTL_CLKBUF CLKBUFOE +# else +# define CONFIG_VR_CTL_CLKBUF 0 +# endif + +# if defined(__ADSPBF52x__) +# define CONFIG_VR_CTL_FREQ FREQ_1000 +# else +# define CONFIG_VR_CTL_FREQ (GAIN_20 | FREQ_1000) +# endif + +# define CONFIG_VR_CTL_VAL (CONFIG_VR_CTL_CLKBUF | CONFIG_VR_CTL_VLEV | CONFIG_VR_CTL_FREQ) +#endif + +__attribute__((saveall)) +void initcode(ADI_BOOT_DATA *bootstruct) +{ + uint32_t old_baud = serial_init(); + +#ifdef CONFIG_HW_WATCHDOG +# ifndef CONFIG_HW_WATCHDOG_TIMEOUT_INITCODE +# define CONFIG_HW_WATCHDOG_TIMEOUT_INITCODE 20000 +# endif + /* Program the watchdog with an initial timeout of ~20 seconds. + * Hopefully that should be long enough to load the u-boot LDR + * (from wherever) and then the common u-boot code can take over. + * In bypass mode, the start.S would have already set a much lower + * timeout, so don't clobber that. + */ + if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_BYPASS) { + bfin_write_WDOG_CNT(MSEC_TO_SCLK(CONFIG_HW_WATCHDOG_TIMEOUT_INITCODE)); + bfin_write_WDOG_CTL(0); + } +#endif + + serial_putc('S'); + + /* Blackfin bootroms use the SPI slow read opcode instead of the SPI + * fast read, so we need to slow down the SPI clock a lot more during + * boot. Once we switch over to u-boot's SPI flash driver, we'll + * increase the speed appropriately. + */ + if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) +#ifdef SPI0_BAUD + bfin_write_SPI0_BAUD(CONFIG_SPI_BAUD_INITBLOCK); +#else + bfin_write_SPI_BAUD(CONFIG_SPI_BAUD_INITBLOCK); +#endif + + serial_putc('B'); + + /* Disable all peripheral wakeups except for the PLL event. */ +#ifdef SIC_IWR0 + bfin_write_SIC_IWR0(1); + bfin_write_SIC_IWR1(0); +# ifdef SIC_IWR2 + bfin_write_SIC_IWR2(0); +# endif +#elif defined(SICA_IWR0) + bfin_write_SICA_IWR0(1); + bfin_write_SICA_IWR1(0); +#else + bfin_write_SIC_IWR(1); +#endif + + serial_putc('L'); + + bfin_write_PLL_LOCKCNT(CONFIG_PLL_LOCKCNT_VAL); + + serial_putc('A'); + + /* Only reprogram when needed to avoid triggering unnecessary + * PLL relock sequences. + */ + if (bfin_read_VR_CTL() != CONFIG_VR_CTL_VAL) { + serial_putc('!'); + bfin_write_VR_CTL(CONFIG_VR_CTL_VAL); + asm("idle;"); + } + + serial_putc('C'); + + bfin_write_PLL_DIV(CONFIG_PLL_DIV_VAL); + + serial_putc('K'); + + /* Only reprogram when needed to avoid triggering unnecessary + * PLL relock sequences. + */ + if (bfin_read_PLL_CTL() != CONFIG_PLL_CTL_VAL) { + serial_putc('!'); + bfin_write_PLL_CTL(CONFIG_PLL_CTL_VAL); + asm("idle;"); + } + + /* Since we've changed the SCLK above, we may need to update + * the UART divisors (UART baud rates are based on SCLK). + */ + serial_reset_baud(old_baud); + + serial_putc('F'); + + /* Program the async banks controller. */ + bfin_write_EBIU_AMBCTL0(CONFIG_EBIU_AMBCTL0_VAL); + bfin_write_EBIU_AMBCTL1(CONFIG_EBIU_AMBCTL1_VAL); + bfin_write_EBIU_AMGCTL(CONFIG_EBIU_AMGCTL_VAL); + +#ifdef EBIU_MODE + /* Not all parts have these additional MMRs. */ + bfin_write_EBIU_MBSCTL(CONFIG_EBIU_MBSCTL_VAL); + bfin_write_EBIU_MODE(CONFIG_EBIU_MODE_VAL); + bfin_write_EBIU_FCTL(CONFIG_EBIU_FCTL_VAL); +#endif + + serial_putc('I'); + + /* Program the external memory controller. */ +#ifdef EBIU_RSTCTL + bfin_write_EBIU_RSTCTL(bfin_read_EBIU_RSTCTL() | 0x1 /*DDRSRESET*/ | CONFIG_EBIU_RSTCTL_VAL); + bfin_write_EBIU_DDRCTL0(CONFIG_EBIU_DDRCTL0_VAL); + bfin_write_EBIU_DDRCTL1(CONFIG_EBIU_DDRCTL1_VAL); + bfin_write_EBIU_DDRCTL2(CONFIG_EBIU_DDRCTL2_VAL); +# ifdef CONFIG_EBIU_DDRCTL3_VAL + /* default is disable, so don't need to force this */ + bfin_write_EBIU_DDRCTL3(CONFIG_EBIU_DDRCTL3_VAL); +# endif +#else + bfin_write_EBIU_SDRRC(CONFIG_EBIU_SDRRC_VAL); + bfin_write_EBIU_SDBCTL(CONFIG_EBIU_SDBCTL_VAL); + bfin_write_EBIU_SDGCTL(CONFIG_EBIU_SDGCTL_VAL); +#endif + + serial_putc('N'); + + /* Restore all peripheral wakeups. */ +#ifdef SIC_IWR0 + bfin_write_SIC_IWR0(-1); + bfin_write_SIC_IWR1(-1); +# ifdef SIC_IWR2 + bfin_write_SIC_IWR2(-1); +# endif +#elif defined(SICA_IWR0) + bfin_write_SICA_IWR0(-1); + bfin_write_SICA_IWR1(-1); +#else + bfin_write_SIC_IWR(-1); +#endif + + serial_putc('>'); + serial_putc('\n'); + + serial_deinit(); +} |