diff options
Diffstat (limited to 'common/cmd_pcmcia.c')
| -rw-r--r-- | common/cmd_pcmcia.c | 193 |
1 files changed, 193 insertions, 0 deletions
diff --git a/common/cmd_pcmcia.c b/common/cmd_pcmcia.c index 9ff0949..1387e89 100644 --- a/common/cmd_pcmcia.c +++ b/common/cmd_pcmcia.c @@ -3091,6 +3091,199 @@ static void cfg_ports (void) /* -------------------------------------------------------------------- */ +/* UC100 Boards */ +/* -------------------------------------------------------------------- */ + +#if defined(CONFIG_UC100) + +#define PCMCIA_BOARD_MSG "UC100" + +/* + * Remark: don't turn off OE "__MY_PCMCIA_GCRX_CXOE" on UC100 board. + * This leads to board-hangup! (sr, 8 Dez. 2004) + */ + +static void cfg_ports (void); + +static int hardware_enable(int slot) +{ + volatile immap_t *immap; + volatile cpm8xx_t *cp; + volatile pcmconf8xx_t *pcmp; + volatile sysconf8xx_t *sysp; + uint reg, mask; + + debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot); + + udelay(10000); + + immap = (immap_t *)CFG_IMMR; + sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf)); + pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia)); + cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm)); + + /* Configure Ports for TPS2211A PC-Card Power-Interface Switch */ + cfg_ports (); + + /* + * Configure SIUMCR to enable PCMCIA port B + * (VFLS[0:1] are not used for debugging, we connect FRZ# instead) + */ + sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */ + + /* clear interrupt state, and disable interrupts */ + pcmp->pcmc_pscr = PCMCIA_MASK(_slot_); + pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_); + + /* + * Disable interrupts, DMA, and PCMCIA buffers + * (isolate the interface) and assert RESET signal + */ + debug ("Disable PCMCIA buffers and assert RESET\n"); + reg = 0; + reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */ + PCMCIA_PGCRX(_slot_) = reg; + udelay(500); + + /* + * Make sure there is a card in the slot, then configure the interface. + */ + udelay(10000); + debug ("[%d] %s: PIPR(%p)=0x%x\n", + __LINE__,__FUNCTION__, + &(pcmp->pcmc_pipr),pcmp->pcmc_pipr); + if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) { + printf (" No Card found\n"); + return (1); + } + + /* + * Power On. + */ + mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot); + reg = pcmp->pcmc_pipr; + debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n", + reg, + (reg&PCMCIA_VS1(slot))?"n":"ff", + (reg&PCMCIA_VS2(slot))?"n":"ff"); + if ((reg & mask) == mask) { + puts (" 5.0V card found: "); + } else { + puts (" 3.3V card found: "); + } + + /* switch VCC on */ + immap->im_ioport.iop_padat |= 0x8000; /* power enable 3.3V */ + + udelay(10000); + + debug ("Enable PCMCIA buffers and stop RESET\n"); + reg = PCMCIA_PGCRX(_slot_); + reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */ + reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */ + PCMCIA_PGCRX(_slot_) = reg; + + udelay(250000); /* some cards need >150 ms to come up :-( */ + + debug ("# hardware_enable done\n"); + + return (0); +} + + +#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA) +static int hardware_disable(int slot) +{ + volatile immap_t *immap; + volatile cpm8xx_t *cp; + volatile pcmconf8xx_t *pcmp; + u_long reg; + + debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot); + + immap = (immap_t *)CFG_IMMR; + pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia)); + + /* switch VCC off */ + immap->im_ioport.iop_padat &= ~0x8000; /* power disable 3.3V */ + + /* Configure PCMCIA General Control Register */ + debug ("Disable PCMCIA buffers and assert RESET\n"); + reg = 0; + reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */ + PCMCIA_PGCRX(_slot_) = reg; + + udelay(10000); + + return (0); +} +#endif /* CFG_CMD_PCMCIA */ + + +static int voltage_set(int slot, int vcc, int vpp) +{ + volatile immap_t *immap; + volatile pcmconf8xx_t *pcmp; + u_long reg; + + debug ("voltage_set: " + PCMCIA_BOARD_MSG + " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n", + 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10); + + immap = (immap_t *)CFG_IMMR; + pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia)); + /* + * Disable PCMCIA buffers (isolate the interface) + * and assert RESET signal + */ + debug ("Disable PCMCIA buffers and assert RESET\n"); + reg = PCMCIA_PGCRX(_slot_); + reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */ + PCMCIA_PGCRX(_slot_) = reg; + udelay(500); + + /* + * Configure Port C pins for + * 5 Volts Enable and 3 Volts enable, + * Turn all power pins to Hi-Z + */ + debug ("PCMCIA power OFF\n"); + cfg_ports (); /* Enables switch, but all in Hi-Z */ + + debug ("Enable PCMCIA buffers and stop RESET\n"); + reg = PCMCIA_PGCRX(_slot_); + reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */ + reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */ + PCMCIA_PGCRX(_slot_) = reg; + udelay(500); + + debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n", + slot+'A'); + return (0); +} + +static void cfg_ports (void) +{ + volatile immap_t *immap; + + immap = (immap_t *)CFG_IMMR; + + /* + * Configure Port A for MAX1602 PC-Card Power-Interface Switch + */ + immap->im_ioport.iop_padat &= ~0x8000; /* set port x output to low */ + immap->im_ioport.iop_padir |= 0x8000; /* enable port x as output */ + + debug ("Set Port A: PAR: %08x DIR: %08x DAT: %08x\n", + immap->im_ioport.iop_papar, immap->im_ioport.iop_padir, + immap->im_ioport.iop_padat); +} + +#endif /* UC100 */ + + +/* -------------------------------------------------------------------- */ #endif /* CFG_CMD_PCMCIA || (CFG_CMD_IDE && CONFIG_IDE_8xx_PCCARD) */ |