diff options
Diffstat (limited to 'board')
| -rw-r--r-- | board/sc3/Kconfig | 9 | ||||
| -rw-r--r-- | board/sc3/MAINTAINERS | 6 | ||||
| -rw-r--r-- | board/sc3/Makefile | 9 | ||||
| -rw-r--r-- | board/sc3/init.S | 360 | ||||
| -rw-r--r-- | board/sc3/sc3.c | 769 | ||||
| -rw-r--r-- | board/sc3/sc3.h | 101 | ||||
| -rw-r--r-- | board/sc3/sc3nand.c | 74 |
7 files changed, 0 insertions, 1328 deletions
diff --git a/board/sc3/Kconfig b/board/sc3/Kconfig deleted file mode 100644 index 88a6d86..0000000 --- a/board/sc3/Kconfig +++ /dev/null @@ -1,9 +0,0 @@ -if TARGET_SC3 - -config SYS_BOARD - default "sc3" - -config SYS_CONFIG_NAME - default "sc3" - -endif diff --git a/board/sc3/MAINTAINERS b/board/sc3/MAINTAINERS deleted file mode 100644 index b86c6e6..0000000 --- a/board/sc3/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -SC3 BOARD -M: Heiko Schocher <hs@denx.de> -S: Maintained -F: board/sc3/ -F: include/configs/sc3.h -F: configs/sc3_defconfig diff --git a/board/sc3/Makefile b/board/sc3/Makefile deleted file mode 100644 index c1d163e..0000000 --- a/board/sc3/Makefile +++ /dev/null @@ -1,9 +0,0 @@ -# -# (C) Copyright 2000 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y = sc3.o sc3nand.o -obj-y += init.o diff --git a/board/sc3/init.S b/board/sc3/init.S deleted file mode 100644 index 097aa4a..0000000 --- a/board/sc3/init.S +++ /dev/null @@ -1,360 +0,0 @@ -/* - * SPDX-License-Identifier: GPL-2.0 IBM-pibs - */ -#include <config.h> -#include <asm/ppc4xx.h> - -#include <ppc_asm.tmpl> -#include <ppc_defs.h> - -#include <asm/cache.h> -#include <asm/mmu.h> - -/** - * ext_bus_cntlr_init - Initializes the External Bus Controller for the external peripherals - * - * IMPORTANT: For pass1 this code must run from cache since you can not - * reliably change a peripheral banks timing register (pbxap) while running - * code from that bank. For ex., since we are running from ROM on bank 0, we - * can NOT execute the code that modifies bank 0 timings from ROM, so - * we run it from cache. - * - * Bank 0 - Boot-Flash - * Bank 1 - NAND-Flash - * Bank 2 - ISA bus - * Bank 3 - Second Flash - * Bank 4 - USB controller - */ - .globl ext_bus_cntlr_init -ext_bus_cntlr_init: -/* - * We need the current boot up configuration to set correct - * timings into internal flash and external flash - */ - mfdcr r24,CPC0_PSR /* xxxx xxxx xxxx xxx? ?xxx xxxx xxxx xxxx - 0 0 -> 8 bit external ROM - 0 1 -> 16 bit internal ROM */ - addi r4,0,2 - srw r24,r24,r4 /* shift right r24 two positions */ - andi. r24,r24,0x06000 -/* - * All calculations are based on 33MHz EBC clock. - * - * First, create a "very slow" timing (~250ns) with burst mode enabled - * This is need for the external flash access - */ - lis r25,0x0800 - /* 0000 1000 0xxx 0000 0000 0010 100x xxxx = 0x03800280 */ - ori r25,r25,0x0280 -/* - * Second, create a fast timing: - * 90ns first cycle - 3 clock access - * and 90ns burst cycle, plus 1 clock after the last access - * This is used for the internal access - */ - lis r26,0x8900 - /* 1000 1001 0xxx 0000 0000 0010 100x xxxx */ - ori r26,r26,0x0280 -/* - * We can't change settings on CS# if we currently use them. - * -> load a few instructions into cache and run this code from cache - */ - mflr r4 /* save link register */ - bl ..getAddr -..getAddr: - mflr r3 /* get address of ..getAddr */ - mtlr r4 /* restore link register */ - addi r4,0,14 /* set ctr to 10; used to prefetch */ - mtctr r4 /* 10 cache lines to fit this function - in cache (gives us 8x10=80 instructions) */ -..ebcloop: - icbt r0,r3 /* prefetch cache line for addr in r3 */ - addi r3,r3,32 /* move to next cache line */ - bdnz ..ebcloop /* continue for 10 cache lines */ -/* - * Delay to ensure all accesses to ROM are complete before changing - * bank 0 timings. 200usec should be enough. - * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles - */ - lis r3,0x0 - ori r3,r3,0xA000 /* ensure 200usec have passed since reset */ - mtctr r3 -..spinlp: - bdnz ..spinlp /* spin loop */ - -/*----------------------------------------------------------------------- - * Memory Bank 0 (BOOT-ROM) initialization - * 0xFFEF00000....0xFFFFFFF - * We only have to change the timing. Mapping is ok by boot-strapping - *----------------------------------------------------------------------- */ - - li r4,PB1AP /* PB0AP=Peripheral Bank 0 Access Parameters */ - mtdcr EBC0_CFGADDR,r4 - - mr r4,r26 /* assume internal fast flash is boot flash */ - cmpwi r24,0x2000 /* assumption true? ... */ - beq 1f /* ...yes! */ - mr r4,r25 /* ...no, use the slow variant */ - mr r25,r26 /* use this for the other flash */ -1: - mtdcr EBC0_CFGDATA,r4 /* change timing now */ - - li r4,PB0CR /* PB0CR=Peripheral Bank 0 Control Register */ - mtdcr EBC0_CFGADDR,r4 - mfdcr r4,EBC0_CFGDATA - lis r3,0x0001 - ori r3,r3,0x8000 /* allow reads and writes */ - or r4,r4,r3 - mtdcr EBC0_CFGDATA,r4 - -/*----------------------------------------------------------------------- - * Memory Bank 3 (Second-Flash) initialization - * 0xF0000000...0xF01FFFFF -> 2MB - *----------------------------------------------------------------------- */ - - li r4,PB3AP /* Peripheral Bank 1 Access Parameter */ - mtdcr EBC0_CFGADDR,r4 - mtdcr EBC0_CFGDATA,r2 /* change timing */ - - li r4,PB3CR /* Peripheral Bank 1 Configuration Registers */ - mtdcr EBC0_CFGADDR,r4 - - lis r4,0xF003 - ori r4,r4,0x8000 -/* - * Consider boot configuration - */ - xori r24,r24,0x2000 /* invert current bus width */ - or r4,r4,r24 - mtdcr EBC0_CFGDATA,r4 - -/*----------------------------------------------------------------------- - * Memory Bank 1 (NAND-Flash) initialization - * 0x77D00000...0x77DFFFFF -> 1MB - * - the write/read pulse to the NAND can be as short as 25ns, bus the cycle time is always 50ns - * - the setup time is 0ns - * - the hold time is 15ns - * -> - * - TWT = 0 - * - CSN = 0 - * - OEN = 0 - * - WBN = 0 - * - WBF = 0 - * - TH = 1 - * ----> 2 clocks per cycle = 60ns cycle (30ns active, 30ns hold) - *----------------------------------------------------------------------- */ - - li r4,PB1AP /* Peripheral Bank 1 Access Parameter */ - mtdcr EBC0_CFGADDR,r4 - - lis r4,0x0000 - ori r4,r4,0x0200 - mtdcr EBC0_CFGDATA,r4 - - li r4,PB1CR /* Peripheral Bank 1 Configuration Registers */ - mtdcr EBC0_CFGADDR,r4 - - lis r4,0x77D1 - ori r4,r4,0x8000 - mtdcr EBC0_CFGDATA,r4 - - -/* USB init (without acceleration) */ -#ifndef CONFIG_ISP1161_PRESENT - li r4,PB4AP /* PB4AP=Peripheral Bank 4 Access Parameters */ - mtdcr EBC0_CFGADDR,r4 - lis r4,0x0180 - ori r4,r4,0x5940 - mtdcr EBC0_CFGDATA,r4 -#endif - -/*----------------------------------------------------------------------- - * Memory Bank 2 (ISA Access) initialization (plus memory bank 6 and 7) - * 0x78000000...0x7BFFFFFF -> 64 MB - * Wir arbeiten bei 33 MHz -> 30ns - *----------------------------------------------------------------------- - - A7 (ppc notation) or A24 (standard notation) decides about - the type of access: - A7/A24=0 -> memory cycle - A7/ /A24=1 -> I/O cycle -*/ - li r4,PB2AP /* PB2AP=Peripheral Bank 2 Access Parameters */ - mtdcr EBC0_CFGADDR,r4 -/* - We emulate an ISA access - - 1. Address active - 2. wait 0 EBC clocks -> CSN=0 - 3. set CS# - 4. wait 0 EBC clock -> OEN/WBN=0 - 5. set OE#/WE# - 6. wait 4 clocks (ca. 90ns) and for Ready signal - 7. hold for 4 clocks -> TH=4 -*/ - -#if 1 -/* faster access to isa-bus */ - lis r4,0x0180 - ori r4,r4,0x5940 -#else - lis r4,0x0100 - ori r4,r4,0x0340 -#endif - mtdcr EBC0_CFGDATA,r4 - -#ifdef IDE_USES_ISA_EMULATION - li r25,PB5AP /* PB5AP=Peripheral Bank 5 Access Parameters */ - mtdcr EBC0_CFGADDR,r25 - mtdcr EBC0_CFGDATA,r4 -#endif - - li r25,PB6AP /* PB6AP=Peripheral Bank 6 Access Parameters */ - mtdcr EBC0_CFGADDR,r25 - mtdcr EBC0_CFGDATA,r4 - li r25,PB7AP /* PB7AP=Peripheral Bank 7 Access Parameters */ - mtdcr EBC0_CFGADDR,r25 - mtdcr EBC0_CFGDATA,r4 - - li r25,PB2CR /* PB2CR=Peripheral Bank 2 Configuration Register */ - mtdcr EBC0_CFGADDR,r25 - - lis r4,0x780B - ori r4,r4,0xA000 - mtdcr EBC0_CFGDATA,r4 -/* - * the other areas are only 1MiB in size - */ - lis r4,0x7401 - ori r4,r4,0xA000 - - li r25,PB6CR /* PB6CR=Peripheral Bank 6 Configuration Register */ - mtdcr EBC0_CFGADDR,r25 - lis r4,0x7401 - ori r4,r4,0xA000 - mtdcr EBC0_CFGDATA,r4 - - li r25,PB7CR /* PB7CR=Peripheral Bank 7 Configuration Register */ - mtdcr EBC0_CFGADDR,r25 - lis r4,0x7411 - ori r4,r4,0xA000 - mtdcr EBC0_CFGDATA,r4 - -#ifndef CONFIG_ISP1161_PRESENT - li r25,PB4CR /* PB4CR=Peripheral Bank 4 Configuration Register */ - mtdcr EBC0_CFGADDR,r25 - lis r4,0x7421 - ori r4,r4,0xA000 - mtdcr EBC0_CFGDATA,r4 -#endif -#ifdef IDE_USES_ISA_EMULATION - li r25,PB5CR /* PB5CR=Peripheral Bank 5 Configuration Register */ - mtdcr EBC0_CFGADDR,r25 - lis r4,0x0000 - ori r4,r4,0x0000 - mtdcr EBC0_CFGDATA,r4 -#endif - -/*----------------------------------------------------------------------- - * Memory bank 4: USB controller Philips ISP6111 - * 0x77C00000 ... 0x77CFFFFF - * - * The chip is connected to: - * - CPU CS#4 - * - CPU IRQ#2 - * - CPU DMA 3 - * - * Timing: - * - command to first data: 300ns. Software must ensure this timing! - * - Write pulse: 26ns - * - Read pulse: 33ns - * - read cycle time: 150ns - * - write cycle time: 140ns - * - * Note: All calculations are based on 33MHz EBC clock. One '#' or '_' is 30ns - * - * |- 300ns --| - * |---- 420ns ---|---- 420ns ---| cycle - * CS ############:###____#######:###____####### - * OE ############:####___#######:####___####### - * WE ############:####__########:####__######## - * - * ----> 2 clocks RD/WR pulses: 60ns - * ----> CSN: 3 clock, 90ns - * ----> OEN: 1 clocks (read cycle) - * ----> WBN: 1 clocks (write cycle) - * ----> WBE: 2 clocks - * ----> TH: 7 clock, 210ns - * ----> TWT: 7 clocks - *----------------------------------------------------------------------- */ - -#ifdef CONFIG_ISP1161_PRESENT - - li r4,PB4AP /* PB4AP=Peripheral Bank 4 Access Parameters */ - mtdcr EBC0_CFGADDR,r4 - - lis r4,0x030D - ori r4,r4,0x5E80 - mtdcr EBC0_CFGDATA,r4 - - li r4,PB4CR /* PB2CR=Peripheral Bank 4 Configuration Register */ - mtdcr EBC0_CFGADDR,r4 - - lis r4,0x77C1 - ori r4,r4,0xA000 - mtdcr EBC0_CFGDATA,r4 - -#endif - -#ifndef IDE_USES_ISA_EMULATION - -/*----------------------------------------------------------------------- - * Memory Bank 5 used for IDE access - * - * Timings for IDE Interface - * - * SETUP / LENGTH / HOLD - cycles valid for 33.3 MHz clk -> 30ns cycle time - * 70 165 30 PIO-Mode 0, [ns] - * 3 6 1 [Cycles] ----> AP=0x040C0200 - * 50 125 20 PIO-Mode 1, [ns] - * 2 5 1 [Cycles] ----> AP=0x03080200 - * 30 100 15 PIO-Mode 2, [ns] - * 1 4 1 [Cycles] ----> AP=0x02040200 - * 30 80 10 PIO-Mode 3, [ns] - * 1 3 1 [Cycles] ----> AP=0x01840200 - * 25 70 10 PIO-Mode 4, [ns] - * 1 3 1 [Cycles] ----> AP=0x01840200 - * - *----------------------------------------------------------------------- */ - - li r4,PB5AP - mtdcr EBC0_CFGADDR,r4 - lis r4,0x040C - ori r4,r4,0x0200 - mtdcr EBC0_CFGDATA,r4 - - li r4,PB5CR /* PB2CR=Peripheral Bank 2 Configuration Register */ - mtdcr EBC0_CFGADDR,r4 - - lis r4,0x7A01 - ori r4,r4,0xA000 - mtdcr EBC0_CFGDATA,r4 -#endif -/* - * External Peripheral Control Register - */ - li r4,EBC0_CFG - mtdcr EBC0_CFGADDR,r4 - - lis r4,0xB84E - ori r4,r4,0xF000 - mtdcr EBC0_CFGDATA,r4 -/* - * drive POST code - */ - lis r4,0x7900 - ori r4,r4,0x0080 - li r3,0x0001 - stb r3,0(r4) /* 01 -> external bus controller is initialized */ - nop /* pass2 DCR errata #8 */ - blr diff --git a/board/sc3/sc3.c b/board/sc3/sc3.c deleted file mode 100644 index 0216a37..0000000 --- a/board/sc3/sc3.c +++ /dev/null @@ -1,769 +0,0 @@ -/* - * (C) Copyright 2007 - * Heiko Schocher, DENX Software Engineering, <hs@denx.de>. - * - * (C) Copyright 2003 - * Juergen Beisert, EuroDesign embedded technologies, info@eurodsn.de - * Derived from walnut.c - * - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <asm/processor.h> -#include <asm/io.h> -#include "sc3.h" -#include <pci.h> -#include <i2c.h> -#include <malloc.h> -#include <netdev.h> - -#undef writel -#undef writeb -#define writeb(b,addr) ((*(volatile u8 *) (addr)) = (b)) -#define writel(b,addr) ((*(volatile u32 *) (addr)) = (b)) - -/* write only register to configure things in our CPLD */ -#define CPLD_CONTROL_1 0x79000102 -#define CPLD_VERSION 0x79000103 - -#define IS_CAMERON ((*(unsigned char *)(CPLD_VERSION)== 0x32) ? 1 : 0) - -static struct pci_controller hose={0,}; - -/************************************************************ - * Standard definition - ************************************************************/ - -/* CPC0_CR0 Function ISA bus - - GPIO0 - - GPIO1 -> Output: NAND-Command Latch Enable - - GPIO2 -> Output: NAND Address Latch Enable - - GPIO3 -> IRQ input ISA-IRQ #5 (through CPLD) - - GPIO4 -> Output: NAND-Chip Enable - - GPIO5 -> IRQ input ISA-IRQ#7 (through CPLD) - - GPIO6 -> IRQ input ISA-IRQ#9 (through CPLD) - - GPIO7 -> IRQ input ISA-IRQ#10 (through CPLD) - - GPIO8 -> IRQ input ISA-IRQ#11 (through CPLD) - - GPIO9 -> IRQ input ISA-IRQ#12 (through CPLD) - - GPIO10/CS1# -> CS1# NAND ISA-CS#0 - - GPIO11/CS2# -> CS2# ISA emulation ISA-CS#1 - - GPIO12/CS3# -> CS3# 2nd Flash-Bank ISA-CS#2 or ISA-CS#7 - - GPIO13/CS4# -> CS4# USB HC or ISA emulation ISA-CS#3 - - GPIO14/CS5# -> CS5# Boosted IDE access ISA-CS#4 - - GPIO15/CS6# -> CS6# ISA emulation ISA-CS#5 - - GPIO16/CS7# -> CS7# ISA emulation ISA-CS#6 - - GPIO17/IRQ0 -> GPIO, in, NAND-Ready/Busy# line ISA-IRQ#3 - - GPIO18/IRQ1 -> IRQ input ISA-IRQ#14 - - GPIO19/IRQ2 -> IRQ input or USB ISA-IRQ#4 - - GPIO20/IRQ3 -> IRQ input PCI-IRQ#D - - GPIO21/IRQ4 -> IRQ input PCI-IRQ#C - - GPIO22/IRQ5 -> IRQ input PCI-IRQ#B - - GPIO23/IRQ6 -> IRQ input PCI-IRQ#A - - GPIO24 -> if GPIO output: 0=JTAG CPLD activ, 1=JTAG CPLD inactiv -*/ -/* -| CPLD register: io-space at offset 0x102 (write only) -| 0 -| 1 -| 2 0=CS#4 USB CS#, 1=ISA or GP bus -| 3 -| 4 -| 5 -| 6 1=enable faster IDE access -| 7 -*/ -#define USB_CHIP_ENABLE 0x04 -#define IDE_BOOSTING 0x40 - -/* --------------- USB stuff ------------------------------------- */ -#ifdef CONFIG_ISP1161_PRESENT -/** - * initUsbHost- Initialize the Philips isp1161 HC part if present - * @cpldConfig: Pointer to value in write only CPLD register - * - * Initialize the USB host controller if present and fills the - * scratch register to inform the driver about used resources - */ - -static void initUsbHost (unsigned char *cpldConfig) -{ - int i; - unsigned long usbBase; - /* - * Read back where init.S has located the USB chip - */ - mtdcr (0x012, 0x04); - usbBase = mfdcr (0x013); - if (!(usbBase & 0x18000)) /* enabled? */ - return; - usbBase &= 0xFFF00000; - - /* - * to test for the USB controller enable using of CS#4 and DMA 3 for USB access - */ - writeb (*cpldConfig | USB_CHIP_ENABLE,CPLD_CONTROL_1); - - /* - * first check: is the controller assembled? - */ - hcWriteWord (usbBase, 0x5555, HcScratch); - if (hcReadWord (usbBase, HcScratch) == 0x5555) { - hcWriteWord (usbBase, 0xAAAA, HcScratch); - if (hcReadWord (usbBase, HcScratch) == 0xAAAA) { - if ((hcReadWord (usbBase, HcChipID) & 0xFF00) != 0x6100) - return; /* this is not our controller */ - /* - * try a software reset. This needs up to 10 seconds (see datasheet) - */ - hcWriteDWord (usbBase, 0x00000001, HcCommandStatus); - for (i = 1000; i > 0; i--) { /* loop up to 10 seconds */ - udelay (10); - if (!(hcReadDWord (usbBase, HcCommandStatus) & 0x01)) - break; - } - - if (!i) - return; /* the controller doesn't responding. Broken? */ - /* - * OK. USB controller is ready. Initialize it in such way the later driver - * can us it (without any knowing about specific implementation) - */ - hcWriteDWord (usbBase, 0x00000000, HcControl); - /* - * disable all interrupt sources. Because we - * don't know where we come from (hard reset, cold start, soft reset...) - */ - hcWriteDWord (usbBase, 0x8000007D, HcInterruptDisable); - /* - * our current setup hardware configuration - * - every port power supply can switched indepently - * - every port can signal overcurrent - * - every port is "outside" and the devices are removeable - */ - hcWriteDWord (usbBase, 0x32000902, HcRhDescriptorA); - hcWriteDWord (usbBase, 0x00060000, HcRhDescriptorB); - /* - * don't forget to switch off power supply of each port - * The later running driver can reenable them to find and use - * the (maybe) connected devices. - * - */ - hcWriteDWord (usbBase, 0x00000200, HcRhPortStatus1); - hcWriteDWord (usbBase, 0x00000200, HcRhPortStatus2); - hcWriteWord (usbBase, 0x0428, HcHardwareConfiguration); - hcWriteWord (usbBase, 0x0040, HcDMAConfiguration); - hcWriteWord (usbBase, 0x0000, HcuPInterruptEnable); - hcWriteWord (usbBase, 0xA000 | (0x03 << 8) | 27, HcScratch); - /* - * controller is present and usable - */ - *cpldConfig |= USB_CHIP_ENABLE; - } - } -} -#endif - -#if defined(CONFIG_START_IDE) -int board_start_ide(void) -{ - if (IS_CAMERON) { - puts ("no IDE on cameron board.\n"); - return 0; - } - return 1; -} -#endif - -static int sc3_cameron_init (void) -{ - /* Set up the Memory Controller for the CAMERON version */ - mtebc (PB4AP, 0x01805940); - mtebc (PB4CR, 0x7401a000); - mtebc (PB5AP, 0x01805940); - mtebc (PB5CR, 0x7401a000); - mtebc (PB6AP, 0x0); - mtebc (PB6CR, 0x0); - mtebc (PB7AP, 0x0); - mtebc (PB7CR, 0x0); - return 0; -} - -void sc3_read_eeprom (void) -{ - uchar i2c_buffer[18]; - - i2c_read (0x50, 0x03, 1, i2c_buffer, 9); - i2c_buffer[9] = 0; - setenv ("serial#", (char *)i2c_buffer); - - /* read mac-address from eeprom */ - i2c_read (0x50, 0x11, 1, i2c_buffer, 15); - i2c_buffer[17] = 0; - i2c_buffer[16] = i2c_buffer[14]; - i2c_buffer[15] = i2c_buffer[13]; - i2c_buffer[14] = ':'; - i2c_buffer[13] = i2c_buffer[12]; - i2c_buffer[12] = i2c_buffer[11]; - i2c_buffer[11] = ':'; - i2c_buffer[8] = ':'; - i2c_buffer[5] = ':'; - i2c_buffer[2] = ':'; - setenv ("ethaddr", (char *)i2c_buffer); -} - -int board_early_init_f (void) -{ - /* write only register to configure things in our CPLD */ - unsigned char cpldConfig_1=0x00; - -/*-------------------------------------------------------------------------+ -| Interrupt controller setup for the SolidCard III CPU card (plus Evaluation board). -| -| Note: IRQ 0 UART 0, active high; level sensitive -| IRQ 1 UART 1, active high; level sensitive -| IRQ 2 IIC, active high; level sensitive -| IRQ 3 Ext. master, rising edge, edge sensitive -| IRQ 4 PCI, active high; level sensitive -| IRQ 5 DMA Channel 0, active high; level sensitive -| IRQ 6 DMA Channel 1, active high; level sensitive -| IRQ 7 DMA Channel 2, active high; level sensitive -| IRQ 8 DMA Channel 3, active high; level sensitive -| IRQ 9 Ethernet Wakeup, active high; level sensitive -| IRQ 10 MAL System Error (SERR), active high; level sensitive -| IRQ 11 MAL Tx End of Buffer, active high; level sensitive -| IRQ 12 MAL Rx End of Buffer, active high; level sensitive -| IRQ 13 MAL Tx Descriptor Error, active high; level sensitive -| IRQ 14 MAL Rx Descriptor Error, active high; level sensitive -| IRQ 15 Ethernet, active high; level sensitive -| IRQ 16 External PCI SERR, active high; level sensitive -| IRQ 17 ECC Correctable Error, active high; level sensitive -| IRQ 18 PCI Power Management, active high; level sensitive -| -| IRQ 19 (EXT IRQ7 405GPr only) -| IRQ 20 (EXT IRQ8 405GPr only) -| IRQ 21 (EXT IRQ9 405GPr only) -| IRQ 22 (EXT IRQ10 405GPr only) -| IRQ 23 (EXT IRQ11 405GPr only) -| IRQ 24 (EXT IRQ12 405GPr only) -| -| IRQ 25 (EXT IRQ 0) NAND-Flash R/B# (raising edge means flash is ready) -| IRQ 26 (EXT IRQ 1) IDE0 interrupt (x86 = IRQ14). Active high (edge sensitive) -| IRQ 27 (EXT IRQ 2) USB controller -| IRQ 28 (EXT IRQ 3) INT D, VGA; active low; level sensitive -| IRQ 29 (EXT IRQ 4) INT C, Ethernet; active low; level sensitive -| IRQ 30 (EXT IRQ 5) INT B, PC104+ SLOT; active low; level sensitive -| IRQ 31 (EXT IRQ 6) INT A, PC104+ SLOT; active low; level sensitive -| -| Direct Memory Access Controller Signal Polarities -| DRQ0 active high (like ISA) -| ACK0 active low (like ISA) -| EOT0 active high (like ISA) -| DRQ1 active high (like ISA) -| ACK1 active low (like ISA) -| EOT1 active high (like ISA) -| DRQ2 active high (like ISA) -| ACK2 active low (like ISA) -| EOT2 active high (like ISA) -| DRQ3 active high (like ISA) -| ACK3 active low (like ISA) -| EOT3 active high (like ISA) -| -+-------------------------------------------------------------------------*/ - - writeb (cpldConfig_1, CPLD_CONTROL_1); /* disable everything in CPLD */ - - mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */ - mtdcr (UIC0ER, 0x00000000); /* disable all ints */ - mtdcr (UIC0CR, 0x00000000); /* set all to be non-critical */ - - if (IS_CAMERON) { - sc3_cameron_init(); - mtdcr (0x0B6, 0x18000000); - mtdcr (UIC0PR, 0xFFFFFFF0); - mtdcr (UIC0TR, 0x10001030); - } else { - mtdcr (0x0B6, 0x0000000); - mtdcr (UIC0PR, 0xFFFFFFE0); - mtdcr (UIC0TR, 0x10000020); - } - mtdcr (UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority */ - mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */ - - /* setup other implementation specific details */ - mtdcr (CPC0_ECR, 0x60606000); - - mtdcr (CPC0_CR1, 0x000042C0); - - if (IS_CAMERON) { - mtdcr (CPC0_CR0, 0x01380000); - /* Setup the GPIOs */ - writel (0x08008000, 0xEF600700); /* Output states */ - writel (0x00000000, 0xEF600718); /* Open Drain control */ - writel (0x68098000, 0xEF600704); /* Output control */ - } else { - mtdcr (CPC0_CR0,0x00080000); - /* Setup the GPIOs */ - writel (0x08000000, 0xEF600700); /* Output states */ - writel (0x14000000, 0xEF600718); /* Open Drain control */ - writel (0x7C000000, 0xEF600704); /* Output control */ - } - - /* Code decompression disabled */ - mtdcr (DCP0_CFGADDR, KCONF); - mtdcr (DCP0_CFGDATA, 0x2B); - - /* CPC0_ER: enable sleep mode of (currently) unused components */ - /* CPC0_FR: force unused components into sleep mode */ - mtdcr (CPC0_ER, 0x3F800000); - mtdcr (CPC0_FR, 0x14000000); - - /* set PLB priority */ - mtdcr (PLB0_ACR, 0x08000000); - - /* --------------- DMA stuff ------------------------------------- */ - mtdcr (0x126, 0x49200000); - -#ifndef IDE_USES_ISA_EMULATION - cpldConfig_1 |= IDE_BOOSTING; /* enable faster IDE */ - /* cpldConfig |= 0x01; */ /* enable 8.33MHz output, if *not* present on your baseboard */ - writeb (cpldConfig_1, CPLD_CONTROL_1); -#endif - -#ifdef CONFIG_ISP1161_PRESENT - initUsbHost (&cpldConfig_1); - writeb (cpldConfig_1, CPLD_CONTROL_1); -#endif - /* FIXME: for what must we do this */ - *(unsigned long *)0x79000080 = 0x0001; - return(0); -} - -int misc_init_r (void) -{ - char *s1; - int i, xilinx_val; - volatile char *xilinx_adr; - xilinx_adr = (char *)0x79000102; - - *xilinx_adr = 0x00; - -/* customer settings ***************************************** */ -/* - s1 = getenv ("function"); - if (s1) { - if (!strcmp (s1, "Rosho")) { - printf ("function 'Rosho' activated\n"); - *xilinx_adr = 0x40; - } - else { - printf (">>>>>>>>>> function %s not recognized\n",s1); - } - } -*/ - -/* individual settings ***************************************** */ - if ((s1 = getenv ("xilinx"))) { - i=0; - xilinx_val = 0; - while (i < 3 && s1[i]) { - if (s1[i] >= '0' && s1[i] <= '9') - xilinx_val = (xilinx_val << 4) + s1[i] - '0'; - else - if (s1[i] >= 'A' && s1[i] <= 'F') - xilinx_val = (xilinx_val << 4) + s1[i] - 'A' + 10; - else - if (s1[i] >= 'a' && s1[i] <= 'f') - xilinx_val = (xilinx_val << 4) + s1[i] - 'a' + 10; - else { - xilinx_val = -1; - break; - } - i++; - } - if (xilinx_val >= 0 && xilinx_val <=255 && i < 3) { - printf ("Xilinx: set to %s\n", s1); - *xilinx_adr = (unsigned char) xilinx_val; - } else - printf ("Xilinx: rejected value %s\n", s1); - } - return 0; -} - -/* ------------------------------------------------------------------------- - * printCSConfig - * - * Print some informations about chips select configurations - * Only used while debugging. - * - * Params: - * - No. of CS pin - * - AP of this CS - * - CR of this CS - * - * Returns - * nothing - ------------------------------------------------------------------------- */ - -#ifdef SC3_DEBUGOUT -static void printCSConfig(int reg,unsigned long ap,unsigned long cr) -{ - const char *bsize[4] = {"8","16","32","?"}; - const unsigned char banks[8] = {1, 2, 4, 8, 16, 32, 64, 128}; - const char *bankaccess[4] = {"disabled", "RO", "WO", "RW"}; - -#define CYCLE 30 /* time of one clock (based on 33MHz) */ - - printf("\nCS#%d",reg); - if (!(cr & 0x00018000)) - puts(" unused"); - else { - if (((cr&0xFFF00000U) & ((banks[(cr & 0x000E0000) >> 17]-1) << 20))) - puts(" Address is not multiple of bank size!"); - - printf("\n -%s bit device", - bsize[(cr & 0x00006000) >> 13]); - printf(" at 0x%08lX", cr & 0xFFF00000U); - printf(" size: %u MB", banks[(cr & 0x000E0000) >> 17]); - printf(" rights: %s", bankaccess[(cr & 0x00018000) >> 15]); - if (ap & 0x80000000) { - printf("\n -Burst device (%luns/%luns)", - (((ap & 0x7C000000) >> 26) + 1) * CYCLE, - (((ap & 0x03800000) >> 23) + 1) * CYCLE); - } else { - printf("\n -Non burst device, active cycle %luns", - (((ap & 0x7F800000) >> 23) + 1) * CYCLE); - printf("\n -Address setup %luns", - ((ap & 0xC0000) >> 18) * CYCLE); - printf("\n -CS active to RD %luns/WR %luns", - ((ap & 0x30000) >> 16) * CYCLE, - ((ap & 0xC000) >> 14) * CYCLE); - printf("\n -WR to CS inactive %luns", - ((ap & 0x3000) >> 12) * CYCLE); - printf("\n -Hold after access %luns", - ((ap & 0xE00) >> 9) * CYCLE); - printf("\n -Ready is %sabled", - ap & 0x100 ? "en" : "dis"); - } - } -} -#endif - -#ifdef SC3_DEBUGOUT - -static unsigned int ap[] = {PB0AP, PB1AP, PB2AP, PB3AP, PB4AP, - PB5AP, PB6AP, PB7AP}; -static unsigned int cr[] = {PB0CR, PB1CR, PB2CR, PB3CR, PB4CR, - PB5CR, PB6CR, PB7CR}; - -static int show_reg (int nr) -{ - unsigned long ul1, ul2; - - mtdcr (EBC0_CFGADDR, ap[nr]); - ul1 = mfdcr (EBC0_CFGDATA); - mtdcr (EBC0_CFGADDR, cr[nr]); - ul2 = mfdcr(EBC0_CFGDATA); - printCSConfig(nr, ul1, ul2); - return 0; -} -#endif - -int checkboard (void) -{ -#ifdef SC3_DEBUGOUT - unsigned long ul1; - int i; - - for (i = 0; i < 8; i++) { - show_reg (i); - } - - mtdcr (EBC0_CFGADDR, EBC0_CFG); - ul1 = mfdcr (EBC0_CFGDATA); - - puts ("\nGeneral configuration:\n"); - - if (ul1 & 0x80000000) - printf(" -External Bus is always driven\n"); - - if (ul1 & 0x400000) - printf(" -CS signals are always driven\n"); - - if (ul1 & 0x20000) - printf(" -PowerDown after %lu clocks\n", - (ul1 & 0x1F000) >> 7); - - switch (ul1 & 0xC0000) - { - case 0xC0000: - printf(" -No external master present\n"); - break; - case 0x00000: - printf(" -8 bit external master present\n"); - break; - case 0x40000: - printf(" -16 bit external master present\n"); - break; - case 0x80000: - printf(" -32 bit external master present\n"); - break; - } - - switch (ul1 & 0x300000) - { - case 0x300000: - printf(" -Prefetch: Illegal setting!\n"); - break; - case 0x000000: - printf(" -1 doubleword prefetch\n"); - break; - case 0x100000: - printf(" -2 doublewords prefetch\n"); - break; - case 0x200000: - printf(" -4 doublewords prefetch\n"); - break; - } - putc ('\n'); -#endif - printf("Board: SolidCard III %s %s version.\n", - (IS_CAMERON ? "Cameron" : "Eurodesign"), CONFIG_SC3_VERSION); - return 0; -} - -static int printSDRAMConfig(char reg, unsigned long cr) -{ - const int bisize[8]={4, 8, 16, 32, 64, 128, 256, 0}; -#ifdef SC3_DEBUGOUT - const char *basize[8]= - {"4", "8", "16", "32", "64", "128", "256", "Reserved"}; - - printf("SDRAM bank %d",reg); - - if (!(cr & 0x01)) - puts(" disabled\n"); - else { - printf(" at 0x%08lX, size %s MB",cr & 0xFFC00000,basize[(cr&0xE0000)>>17]); - printf(" mode %lu\n",((cr & 0xE000)>>13)+1); - } -#endif - - if (cr & 0x01) - return(bisize[(cr & 0xE0000) >> 17]); - - return 0; -} - -#ifdef SC3_DEBUGOUT -static unsigned int mbcf[] = {SDRAM0_B0CR, SDRAM0_B1CR, SDRAM0_B2CR, SDRAM0_B3CR}; -#endif - -phys_size_t initdram (int board_type) -{ - unsigned int mems=0; - unsigned long ul1; - -#ifdef SC3_DEBUGOUT - unsigned long ul2; - int i; - - puts("\nSDRAM configuration:\n"); - - mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG); - ul1 = mfdcr(SDRAM0_CFGDATA); - - if (!(ul1 & 0x80000000)) { - puts(" Controller disabled\n"); - return 0; - } - for (i = 0; i < 4; i++) { - mtdcr (SDRAM0_CFGADDR, mbcf[i]); - ul1 = mfdcr (SDRAM0_CFGDATA); - mems += printSDRAMConfig (i, ul1); - } - - mtdcr (SDRAM0_CFGADDR, SDRAM0_TR); - ul1 = mfdcr(SDRAM0_CFGDATA); - - printf ("Timing:\n -CAS latency %lu\n", ((ul1 & 0x1800000) >> 23)+1); - printf (" -Precharge %lu (PTA) \n", ((ul1 & 0xC0000) >> 18) + 1); - printf (" -R/W to Precharge %lu (CTP)\n", ((ul1 & 0x30000) >> 16) + 1); - printf (" -Leadoff %lu\n", ((ul1 & 0xC000) >> 14) + 1); - printf (" -CAS to RAS %lu\n", ((ul1 & 0x1C) >> 2) + 4); - printf (" -RAS to CAS %lu\n", ((ul1 & 0x3) + 1)); - puts ("Misc:\n"); - mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR); - ul1 = mfdcr(SDRAM0_CFGDATA); - printf (" -Refresh rate: %luns\n", (ul1 >> 16) * 7); - - mtdcr(SDRAM0_CFGADDR,SDRAM0_PMIT); - ul2=mfdcr(SDRAM0_CFGDATA); - - mtdcr(SDRAM0_CFGADDR,SDRAM0_CFG); - ul1=mfdcr(SDRAM0_CFGDATA); - - if (ul1 & 0x20000000) - printf(" -Power Down after: %luns\n", - ((ul2 & 0xFFC00000) >> 22) * 7); - else - puts(" -Power Down disabled\n"); - - if (ul1 & 0x40000000) - printf(" -Self refresh feature active\n"); - else - puts(" -Self refresh disabled\n"); - - if (ul1 & 0x10000000) - puts(" -ECC enabled\n"); - else - puts(" -ECC disabled\n"); - - if (ul1 & 0x8000000) - puts(" -Using registered SDRAM\n"); - - if (!(ul1 & 0x6000000)) - puts(" -Using 32 bit data width\n"); - else - puts(" -Illegal data width!\n"); - - if (ul1 & 0x400000) - puts(" -ECC drivers inactive\n"); - else - puts(" -ECC drivers active\n"); - - if (ul1 & 0x200000) - puts(" -Memory lines always active outputs\n"); - else - puts(" -Memory lines only at write cycles active outputs\n"); - - mtdcr (SDRAM0_CFGADDR, SDRAM0_STATUS); - ul1 = mfdcr (SDRAM0_CFGDATA); - if (ul1 & 0x80000000) - puts(" -SDRAM Controller ready\n"); - else - puts(" -SDRAM Controller not ready\n"); - - if (ul1 & 0x4000000) - puts(" -SDRAM in self refresh mode!\n"); - - return (mems * 1024 * 1024); -#else - mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR); - ul1 = mfdcr (SDRAM0_CFGDATA); - mems = printSDRAMConfig (0, ul1); - - mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR); - ul1 = mfdcr (SDRAM0_CFGDATA); - mems += printSDRAMConfig (1, ul1); - - mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR); - ul1 = mfdcr(SDRAM0_CFGDATA); - mems += printSDRAMConfig (2, ul1); - - mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR); - ul1 = mfdcr(SDRAM0_CFGDATA); - mems += printSDRAMConfig (3, ul1); - - return (mems * 1024 * 1024); -#endif -} - -static void pci_solidcard3_fixup_irq (struct pci_controller *hose, pci_dev_t dev) -{ -/*-------------------------------------------------------------------------+ - | ,-. ,-. ,-. ,-. ,-. - | INTD# ----|B|-----|P|-. ,-|P|-. ,-| |-. ,-|G| - | |R| |C| \ / |C| \ / |E| \ / |r| - | INTC# ----|I|-----|1|-. `/---|1|-. `/---|t|-. `/---|a| - | |D| |0| \/ |0| \/ |h| \/ |f| - | INTB# ----|G|-----|4|-./`----|4|-./`----|e|-./`----|i| - | |E| |+| /\ |+| /\ |r| /\ |k| - | INTA# ----| |-----| |- `----| |- `----| |- `----| | - | `-' `-' `-' `-' `-' - | Slot 0 10 11 12 13 - | REQ# 0 1 2 * - | GNT# 0 1 2 * - +-------------------------------------------------------------------------*/ - unsigned char int_line = 0xff; - - switch (PCI_DEV(dev)) { - case 10: - int_line = 31; /* INT A */ - POST_OUT(0x42); - break; - - case 11: - int_line = 30; /* INT B */ - POST_OUT(0x43); - break; - - case 12: - int_line = 29; /* INT C */ - POST_OUT(0x44); - break; - - case 13: - int_line = 28; /* INT D */ - POST_OUT(0x45); - break; - } - pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, int_line); -} - -extern void pci_405gp_init(struct pci_controller *hose); -extern void pci_405gp_fixup_irq(struct pci_controller *hose, pci_dev_t dev); -extern void pci_405gp_setup_bridge(struct pci_controller *hose, pci_dev_t dev,struct pci_config_table *entry); -/* - * The following table is used when there is a special need to setup a PCI device. - * For every PCI device found in this table is called the given init function with given - * parameters. So never let all IDs at PCI_ANY_ID. In this case any found device gets the same - * parameters! - * -*/ -static struct pci_config_table pci_solidcard3_config_table[] = -{ -/* Host to PCI Bridge device (405GP) */ - { - vendor: 0x1014, - device: 0x0156, - class: PCI_CLASS_BRIDGE_HOST, - bus: 0, - dev: 0, - func: 0, - config_device: pci_405gp_setup_bridge - }, - { } -}; - -/*-------------------------------------------------------------------------+ - | pci_init_board (Called from pci_init() in drivers/pci/pci.c) - | - | Init the PCI part of the SolidCard III - | - | Params: - * - Pointer to current PCI hose - * - Current Device - * - * Returns - * nothing - +-------------------------------------------------------------------------*/ - -void pci_init_board(void) -{ - POST_OUT(0x41); -/* - * we want the ptrs to RAM not flash (ie don't use init list) - */ - hose.fixup_irq = pci_solidcard3_fixup_irq; - hose.config_table = pci_solidcard3_config_table; - pci_405gp_init(&hose); -} - -int board_eth_init(bd_t *bis) -{ - return pci_eth_init(bis); -} diff --git a/board/sc3/sc3.h b/board/sc3/sc3.h deleted file mode 100644 index 7178cd0..0000000 --- a/board/sc3/sc3.h +++ /dev/null @@ -1,101 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/** - * hcWriteWord - write a 16 bit value into the USB controller - * @base: base address to access the chip registers - * @value: 16 bit value to write into register @offset - * @offset: register to write the @value into - * - */ -static void inline hcWriteWord (unsigned long base, unsigned int value, - unsigned int offset) -{ - out_le16 ((volatile u16*)(base + 2), offset | 0x80); - out_le16 ((volatile u16*)base, value); -} - -/** - * hcWriteDWord - write a 32 bit value into the USB controller - * @base: base address to access the chip registers - * @value: 32 bit value to write into register @offset - * @offset: register to write the @value into - * - */ - -static void inline hcWriteDWord (unsigned long base, unsigned long value, - unsigned int offset) -{ - out_le16 ((volatile u16*)(base + 2), offset | 0x80); - out_le16 ((volatile u16*)base, value); - out_le16 ((volatile u16*)base, value >> 16); -} - -/** - * hcReadWord - read a 16 bit value from the USB controller - * @base: base address to access the chip registers - * @offset: register to read from - * - * Returns the readed register value - */ - -static unsigned int inline hcReadWord (unsigned long base, unsigned int offset) -{ - out_le16 ((volatile u16*)(base + 2), offset); - return (in_le16 ((volatile u16*)base)); -} - -/** - * hcReadDWord - read a 32 bit value from the USB controller - * @base: base address to access the chip registers - * @offset: register to read from - * - * Returns the readed register value - */ - -static unsigned long inline hcReadDWord (unsigned long base, unsigned int offset) -{ - unsigned long val, val16; - - out_le16 ((volatile u16*)(base + 2), offset); - val = in_le16((volatile u16*)base); - val16 = in_le16((volatile u16*)base); - return (val | (val16 << 16)); -} - -/* control and status registers isp1161 */ -#define HcRevision 0x00 -#define HcControl 0x01 -#define HcCommandStatus 0x02 -#define HcInterruptStatus 0x03 -#define HcInterruptEnable 0x04 -#define HcInterruptDisable 0x05 -#define HcFmInterval 0x0D -#define HcFmRemaining 0x0E -#define HcFmNumber 0x0F -#define HcLSThreshold 0x11 -#define HcRhDescriptorA 0x12 -#define HcRhDescriptorB 0x13 -#define HcRhStatus 0x14 -#define HcRhPortStatus1 0x15 -#define HcRhPortStatus2 0x16 - -#define HcHardwareConfiguration 0x20 -#define HcDMAConfiguration 0x21 -#define HcTransferCounter 0x22 -#define HcuPInterrupt 0x24 -#define HcuPInterruptEnable 0x25 -#define HcChipID 0x27 -#define HcScratch 0x28 -#define HcSoftwareReset 0x29 -#define HcITLBufferLength 0x2A -#define HcATLBufferLength 0x2B -#define HcBufferStatus 0x2C -#define HcReadBackITL0Length 0x2D -#define HcReadBackITL1Length 0x2E -#define HcITLBufferPort 0x40 -#define HcATLBufferPort 0x41 diff --git a/board/sc3/sc3nand.c b/board/sc3/sc3nand.c deleted file mode 100644 index a26cd79..0000000 --- a/board/sc3/sc3nand.c +++ /dev/null @@ -1,74 +0,0 @@ -/* - * (C) Copyright 2007 - * Heiko Schocher, DENX Software Engineering, hs@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> - -#if defined(CONFIG_CMD_NAND) - -#include <nand.h> -#include <asm/processor.h> - -#define readb(addr) *(volatile u_char *)(addr) -#define readl(addr) *(volatile u_long *)(addr) -#define writeb(d,addr) *(volatile u_char *)(addr) = (d) - -#define SC3_NAND_ALE 29 /* GPIO PIN 3 */ -#define SC3_NAND_CLE 30 /* GPIO PIN 2 */ -#define SC3_NAND_CE 27 /* GPIO PIN 5 */ - -static void *sc3_io_base; -static void *sc3_control_base = (void *)0xEF600700; - -static void sc3_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) -{ - struct nand_chip *this = mtd->priv; - if (ctrl & NAND_CTRL_CHANGE) { - if ( ctrl & NAND_CLE ) - set_bit (SC3_NAND_CLE, sc3_control_base); - else - clear_bit (SC3_NAND_CLE, sc3_control_base); - if ( ctrl & NAND_ALE ) - set_bit (SC3_NAND_ALE, sc3_control_base); - else - clear_bit (SC3_NAND_ALE, sc3_control_base); - if ( ctrl & NAND_NCE ) - set_bit (SC3_NAND_CE, sc3_control_base); - else - clear_bit (SC3_NAND_CE, sc3_control_base); - } - - if (cmd != NAND_CMD_NONE) - writeb(cmd, this->IO_ADDR_W); -} - -static int sc3_nand_dev_ready(struct mtd_info *mtd) -{ - if (!(readl(sc3_control_base + 0x1C) & 0x4000)) - return 0; - return 1; -} - -static void sc3_select_chip(struct mtd_info *mtd, int chip) -{ - clear_bit (SC3_NAND_CE, sc3_control_base); -} - -int board_nand_init(struct nand_chip *nand) -{ - nand->ecc.mode = NAND_ECC_SOFT; - - sc3_io_base = (void *) CONFIG_SYS_NAND_BASE; - /* Set address of NAND IO lines (Using Linear Data Access Region) */ - nand->IO_ADDR_R = (void __iomem *) sc3_io_base; - nand->IO_ADDR_W = (void __iomem *) sc3_io_base; - /* Reference hardware control function */ - nand->cmd_ctrl = sc3_nand_hwcontrol; - nand->dev_ready = sc3_nand_dev_ready; - nand->select_chip = sc3_select_chip; - return 0; -} -#endif |