diff options
Diffstat (limited to 'board')
| -rw-r--r-- | board/bct-brettl2/cled.c | 2 | ||||
| -rw-r--r-- | board/davedenx/qong/fpga.c | 1 | ||||
| -rw-r--r-- | board/isee/igep0030/config.mk | 1 | ||||
| -rw-r--r-- | board/xes/common/fsl_8xxx_misc.c | 10 | ||||
| -rw-r--r-- | board/xes/xpedite550x/ddr.c | 21 |
5 files changed, 15 insertions, 20 deletions
diff --git a/board/bct-brettl2/cled.c b/board/bct-brettl2/cled.c index 9e73c57..dcb91bd 100644 --- a/board/bct-brettl2/cled.c +++ b/board/bct-brettl2/cled.c @@ -13,7 +13,7 @@ int do_cled(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { - ulong addr = 0x20000000 + 0x200000; // AMS2 + ulong addr = 0x20000000 + 0x200000; /* AMS2 */ uchar data; if (argc < 2) diff --git a/board/davedenx/qong/fpga.c b/board/davedenx/qong/fpga.c index f865eb4..656d5cd 100644 --- a/board/davedenx/qong/fpga.c +++ b/board/davedenx/qong/fpga.c @@ -92,4 +92,3 @@ int qong_fpga_init(void) } #endif - diff --git a/board/isee/igep0030/config.mk b/board/isee/igep0030/config.mk index 35865e0..019f93f 100644 --- a/board/isee/igep0030/config.mk +++ b/board/isee/igep0030/config.mk @@ -31,4 +31,3 @@ # For use with external or internal boots. TEXT_BASE = 0x80008000 - diff --git a/board/xes/common/fsl_8xxx_misc.c b/board/xes/common/fsl_8xxx_misc.c index b7fa695..36e9146 100644 --- a/board/xes/common/fsl_8xxx_misc.c +++ b/board/xes/common/fsl_8xxx_misc.c @@ -52,11 +52,9 @@ uint get_board_derivative(void) #endif /* - * The top 4 lines of the local bus address are pulled low/high and - * can be read to determine the least significant digit of a board's - * model number. - */ + * The top 4 lines of the local bus address are pulled low/high and + * can be read to determine the least significant digit of a board's + * model number. + */ return gur->gpporcr >> 28; } - - diff --git a/board/xes/xpedite550x/ddr.c b/board/xes/xpedite550x/ddr.c index 718cd98..38a4597 100644 --- a/board/xes/xpedite550x/ddr.c +++ b/board/xes/xpedite550x/ddr.c @@ -55,16 +55,16 @@ unsigned int fsl_ddr_get_mem_data_rate(void) * There are traditionally three board-specific SDRAM timing parameters * which must be calculated based on the particular PCB artwork. These are: * 1.) CPO (Read Capture Delay) - * - TIMING_CFG_2 register - * Source: Calculation based on board trace lengths and - * chip-specific internal delays. + * - TIMING_CFG_2 register + * Source: Calculation based on board trace lengths and + * chip-specific internal delays. * 2.) CLK_ADJUST (Clock and Addr/Cmd alignment control) - * - DDR_SDRAM_CLK_CNTL register - * Source: Signal Integrity Simulations + * - DDR_SDRAM_CLK_CNTL register + * Source: Signal Integrity Simulations * 3.) 2T Timing on Addr/Ctl - * - TIMING_CFG_2 register - * Source: Signal Integrity Simulations - * Usually only needed with heavy load/very high speed (>DDR2-800) + * - TIMING_CFG_2 register + * Source: Signal Integrity Simulations + * Usually only needed with heavy load/very high speed (>DDR2-800) * * ====== XPedite550x DDR3-800 read delay calculations ====== * @@ -82,14 +82,14 @@ typedef struct { const board_specific_parameters_t board_specific_parameters[][20] = { { /* Controller 0 */ - { + { /* DDR3-600/667 */ .datarate_mhz_low = 500, .datarate_mhz_high = 750, .clk_adjust = 5, .cpo = 31, }, - { + { /* DDR3-800 */ .datarate_mhz_low = 750, .datarate_mhz_high = 850, @@ -162,4 +162,3 @@ void fsl_ddr_board_options(memctl_options_t *popts, popts->rtt_override = 1; popts->rtt_override_value = 3; } - |