diff options
Diffstat (limited to 'board')
| -rw-r--r-- | board/keymile/common/common.c | 6 | ||||
| -rw-r--r-- | board/keymile/km_arm/Makefile | 51 | ||||
| -rw-r--r-- | board/keymile/km_arm/config.mk | 28 | ||||
| -rw-r--r-- | board/keymile/km_arm/km_arm.c | 324 | ||||
| -rw-r--r-- | board/keymile/km_arm/kwbimage.cfg | 176 |
5 files changed, 583 insertions, 2 deletions
diff --git a/board/keymile/common/common.c b/board/keymile/common/common.c index ec27bda..7b4eefd 100644 --- a/board/keymile/common/common.c +++ b/board/keymile/common/common.c @@ -35,6 +35,7 @@ #include <libfdt.h> #endif +#include "../common/common.h" #if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) #include <i2c.h> @@ -421,7 +422,6 @@ static int get_scl (void) return ((val & SCL_BIT) == SCL_BIT); } - #endif #if !defined(CONFIG_KMETER1) @@ -500,7 +500,7 @@ void i2c_init_board(void) out_8 (&dev->cr, (I2C_CR_MEN)); #else -#if defined(CONFIG_HARD_I2C) +#if defined(CONFIG_HARD_I2C) && !defined(CONFIG_MACH_SUEN3) volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR ; volatile i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c; @@ -578,10 +578,12 @@ int fdt_get_node_and_value (void *blob, } #endif +#if !defined(CONFIG_MACH_SUEN3) int ethernet_present (void) { return (in_8((u8 *)CONFIG_SYS_PIGGY_BASE + CONFIG_SYS_SLOT_ID_OFF) & 0x80); } +#endif int board_eth_init (bd_t *bis) { diff --git a/board/keymile/km_arm/Makefile b/board/keymile/km_arm/Makefile new file mode 100644 index 0000000..fffc6a3 --- /dev/null +++ b/board/keymile/km_arm/Makefile @@ -0,0 +1,51 @@ +# +# (C) Copyright 2009 +# Marvell Semiconductor <www.marvell.com> +# Prafulla Wadaskar <prafulla@marvell.com> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, +# MA 02110-1301 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := $(BOARD).o ../common/common.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/keymile/km_arm/config.mk b/board/keymile/km_arm/config.mk new file mode 100644 index 0000000..b9e81b2 --- /dev/null +++ b/board/keymile/km_arm/config.mk @@ -0,0 +1,28 @@ +# +# (C) Copyright 2009 +# Marvell Semiconductor <www.marvell.com> +# Prafulla Wadaskar <prafulla@marvell.com> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, +# MA 02110-1301 USA +# + +TEXT_BASE = 0x004000000 + +# Kirkwood Boot Image configuration file +KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c new file mode 100644 index 0000000..53cf474 --- /dev/null +++ b/board/keymile/km_arm/km_arm.c @@ -0,0 +1,324 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Prafulla Wadaskar <prafulla@marvell.com> + * + * (C) Copyright 2009 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * (C) Copyright 2010 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#include <common.h> +#include <i2c.h> +#include <nand.h> +#include <netdev.h> +#include <miiphy.h> +#include <asm/io.h> +#include <asm/arch/kirkwood.h> +#include <asm/arch/mpp.h> + +#include "../common/common.h" + +DECLARE_GLOBAL_DATA_PTR; + +static int io_dev; +extern I2C_MUX_DEVICE *i2c_mux_ident_muxstring (uchar *buf); + +/* Multi-Purpose Pins Functionality configuration */ +u32 kwmpp_config[] = { + MPP0_NF_IO2, + MPP1_NF_IO3, + MPP2_NF_IO4, + MPP3_NF_IO5, + MPP4_NF_IO6, + MPP5_NF_IO7, + MPP6_SYSRST_OUTn, + MPP7_PEX_RST_OUTn, +#if defined(CONFIG_SOFT_I2C) + MPP8_GPIO, /* SDA */ + MPP9_GPIO, /* SCL */ +#endif +#if defined(CONFIG_HARD_I2C) + MPP8_TW_SDA, + MPP9_TW_SCK, +#endif + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP12_GPO, /* Reserved */ + MPP13_UART1_TXD, + MPP14_UART1_RXD, + MPP15_GPIO, /* Not used */ + MPP16_GPIO, /* Not used */ + MPP17_GPIO, /* Reserved */ + MPP18_NF_IO0, + MPP19_NF_IO1, + MPP20_GPIO, + MPP21_GPIO, + MPP22_GPIO, + MPP23_GPIO, + MPP24_GPIO, + MPP25_GPIO, + MPP26_GPIO, + MPP27_GPIO, + MPP28_GPIO, + MPP29_GPIO, + MPP30_GPIO, + MPP31_GPIO, + MPP32_GPIO, + MPP33_GPIO, + MPP34_GPIO, /* CDL1 (input) */ + MPP35_GPIO, /* CDL2 (input) */ + MPP36_GPIO, /* MAIN_IRQ (input) */ + MPP37_GPIO, /* BOARD_LED */ + MPP38_GPIO, /* Piggy3 LED[1] */ + MPP39_GPIO, /* Piggy3 LED[2] */ + MPP40_GPIO, /* Piggy3 LED[3] */ + MPP41_GPIO, /* Piggy3 LED[4] */ + MPP42_GPIO, /* Piggy3 LED[5] */ + MPP43_GPIO, /* Piggy3 LED[6] */ + MPP44_GPIO, /* Piggy3 LED[7] */ + MPP45_GPIO, /* Piggy3 LED[8] */ + MPP46_GPIO, /* Reserved */ + MPP47_GPIO, /* Reserved */ + MPP48_GPIO, /* Reserved */ + MPP49_GPIO, /* SW_INTOUTn */ + 0 +}; + +int ethernet_present(void) +{ + uchar buf; + int ret = 0; + + if (i2c_read(0x10, 2, 1, &buf, 1) != 0) { + printf ("%s: Error reading Boco\n", __FUNCTION__); + return -1; + } + if ((buf & 0x40) == 0x40) { + ret = 1; + } + return ret; +} + +int misc_init_r(void) +{ + I2C_MUX_DEVICE *i2cdev; + char *str; + int mach_type; + + /* add I2C Bus for I/O Expander */ + i2cdev = i2c_mux_ident_muxstring((uchar *)"pca9554a:70:a"); + io_dev = i2cdev->busid; + puts("Piggy:"); + if (ethernet_present() == 0) + puts (" not"); + puts(" present\n"); + + str = getenv("mach_type"); + if (str != NULL) { + mach_type = simple_strtoul(str, NULL, 10); + printf("Overwriting MACH_TYPE with %d!!!\n", mach_type); + gd->bd->bi_arch_number = mach_type; + } + return 0; +} + +int board_init(void) +{ + u32 tmp; + + kirkwood_mpp_conf(kwmpp_config); + + /* + * The FLASH_GPIO_PIN switches between using a + * NAND or a SPI FLASH. Set this pin on start + * to NAND mode. + */ + tmp = readl(KW_GPIO0_BASE); + writel(tmp | FLASH_GPIO_PIN , KW_GPIO0_BASE); + tmp = readl(KW_GPIO0_BASE + 4); + writel(tmp & (~FLASH_GPIO_PIN) , KW_GPIO0_BASE + 4); + printf("KM: setting NAND mode\n"); + + /* + * arch number of board + */ + gd->bd->bi_arch_number = MACH_TYPE_SUEN3; + + /* address of boot parameters */ + gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100; + +#if defined(CONFIG_SOFT_I2C) + /* init the GPIO for I2C Bitbang driver */ + kw_gpio_set_valid(SUEN3_SDA_PIN, 1); + kw_gpio_set_valid(SUEN3_SCL_PIN, 1); + kw_gpio_direction_output(SUEN3_SDA_PIN, 0); + kw_gpio_direction_output(SUEN3_SCL_PIN, 0); +#endif +#if defined(CONFIG_SYS_EEPROM_WREN) + kw_gpio_set_valid(SUEN3_ENV_WP, 38); + kw_gpio_direction_output(SUEN3_ENV_WP, 1); +#endif + return 0; +} + +#if defined(CONFIG_CMD_SF) +int do_spi_toggle(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + u32 tmp; + if (argc < 2) { + cmd_usage(cmdtp); + return 1; + } + + if ((strcmp(argv[1], "off") == 0)) { + printf("SPI FLASH disabled, NAND enabled\n"); + /* Multi-Purpose Pins Functionality configuration */ + kwmpp_config[0] = MPP0_NF_IO2; + kwmpp_config[1] = MPP1_NF_IO3; + kwmpp_config[2] = MPP2_NF_IO4; + kwmpp_config[3] = MPP3_NF_IO5; + + kirkwood_mpp_conf(kwmpp_config); + tmp = readl(KW_GPIO0_BASE); + writel(tmp | FLASH_GPIO_PIN , KW_GPIO0_BASE); + } else if ((strcmp(argv[1], "on") == 0)) { + printf("SPI FLASH enabled, NAND disabled\n"); + /* Multi-Purpose Pins Functionality configuration */ + kwmpp_config[0] = MPP0_SPI_SCn; + kwmpp_config[1] = MPP1_SPI_MOSI; + kwmpp_config[2] = MPP2_SPI_SCK; + kwmpp_config[3] = MPP3_SPI_MISO; + + kirkwood_mpp_conf(kwmpp_config); + tmp = readl(KW_GPIO0_BASE); + writel(tmp & (~FLASH_GPIO_PIN) , KW_GPIO0_BASE); + } else { + cmd_usage(cmdtp); + return 1; + } + + return 0; +} + +U_BOOT_CMD( + spitoggle, 2, 0, do_spi_toggle, + "En-/disable SPI FLASH access", + "<on|off> - Enable (on) or disable (off) SPI FLASH access\n" + ); +#endif + +int dram_init(void) +{ + int i; + + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { + gd->bd->bi_dram[i].start = kw_sdram_bar(i); + gd->bd->bi_dram[i].size = get_ram_size((long *)kw_sdram_bar(i), + kw_sdram_bs(i)); + } + return 0; +} + +/* Configure and enable MV88E1118 PHY */ +void reset_phy(void) +{ + char *name = "egiga0"; + + if (miiphy_set_current_dev(name)) + return; + + /* reset the phy */ + miiphy_reset(name, CONFIG_PHY_BASE_ADR); +} + +#if defined(CONFIG_HUSH_INIT_VAR) +int hush_init_var (void) +{ + ivm_read_eeprom (); + return 0; +} +#endif + +#if defined(CONFIG_BOOTCOUNT_LIMIT) +void bootcount_store (ulong a) +{ + volatile ulong *save_addr; + volatile ulong size = 0; + int i; + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { + size += gd->bd->bi_dram[i].size; + } + save_addr = (ulong*)(size - BOOTCOUNT_ADDR); + writel(a, save_addr); + writel(BOOTCOUNT_MAGIC, &save_addr[1]); +} + +ulong bootcount_load (void) +{ + volatile ulong *save_addr; + volatile ulong size = 0; + int i; + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { + size += gd->bd->bi_dram[i].size; + } + save_addr = (ulong*)(size - BOOTCOUNT_ADDR); + if (readl(&save_addr[1]) != BOOTCOUNT_MAGIC) + return 0; + else + return readl(save_addr); +} +#endif + +#if defined(CONFIG_SOFT_I2C) +void set_sda (int state) +{ + I2C_ACTIVE; + I2C_SDA(state); +} + +void set_scl (int state) +{ + I2C_SCL(state); +} + +int get_sda (void) +{ + I2C_TRISTATE; + return I2C_READ; +} + +int get_scl (void) +{ + return (kw_gpio_get_value(SUEN3_SCL_PIN) ? 1 : 0); +} +#endif + +#if defined(CONFIG_SYS_EEPROM_WREN) +int eeprom_write_enable (unsigned dev_addr, int state) +{ + kw_gpio_set_value(SUEN3_ENV_WP, !state); + + return !kw_gpio_get_value(SUEN3_ENV_WP); +} +#endif diff --git a/board/keymile/km_arm/kwbimage.cfg b/board/keymile/km_arm/kwbimage.cfg new file mode 100644 index 0000000..d6edd27 --- /dev/null +++ b/board/keymile/km_arm/kwbimage.cfg @@ -0,0 +1,176 @@ +# +# (C) Copyright 2010 +# Heiko Schocher, DENX Software Engineering, hs@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, +# MA 02110-1301 USA +# +# Refer docs/README.kwimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM spi # Boot from SPI flash + +DATA 0xFFD10000 0x01111111 # MPP Control 0 Register +# bit 3-0: MPPSel0 1, NF_IO[2] +# bit 7-4: MPPSel1 1, NF_IO[3] +# bit 12-8: MPPSel2 1, NF_IO[4] +# bit 15-12: MPPSel3 1, NF_IO[5] +# bit 19-16: MPPSel4 1, NF_IO[6] +# bit 23-20: MPPSel5 1, NF_IO[7] +# bit 27-24: MPPSel6 1, SYSRST_O +# bit 31-28: MPPSel7 0, GPO[7] + +DATA 0xFFD10008 0x00001100 # MPP Control 2 Register +# bit 3-0: MPPSel16 0, GPIO[16] +# bit 7-4: MPPSel17 0, GPIO[17] +# bit 12-8: MPPSel18 1, NF_IO[0] +# bit 15-12: MPPSel19 1, NF_IO[1] +# bit 19-16: MPPSel20 0, GPIO[20] +# bit 23-20: MPPSel21 0, GPIO[21] +# bit 27-24: MPPSel22 0, GPIO[22] +# bit 31-28: MPPSel23 0, GPIO[23] + +DATA 0xFFD100E0 0x1B1B1B1B # IO Configuration 0 Register +DATA 0xFFD20134 0xBBBBBBBB # L2 RAM Timing 0 Register +DATA 0xFFD20138 0x00BBBBBB # L2 RAM Timing 1 Register +DATA 0xFFD20154 0x00000200 # CPU RAM Management Control3 Register +DATA 0xFFD2014C 0x00001C00 # CPU RAM Management Control1 Register +DATA 0xFFD20148 0x00000001 # CPU RAM Management Control0 Register + +#Dram initalization +DATA 0xFFD01400 0x43000400 # SDRAM Configuration Register +# bit13-0: 0x400 (DDR2 clks refresh rate) +# bit23-14: zero +# bit24: 1= enable exit self refresh mode on DDR access +# bit25: 1 required +# bit29-26: zero +# bit31-30: 01 + +DATA 0xFFD01404 0x36343000 # DDR Controller Control Low + 0x38543000 +# bit 3-0: 0 reserved +# bit 4: 0=addr/cmd in smame cycle +# bit 5: 0=clk is driven during self refresh, we don't care for APX +# bit 6: 0=use recommended falling edge of clk for addr/cmd +# bit14: 0=input buffer always powered up +# bit18: 1=cpu lock transaction enabled +# bit23-20: 3=recommended value for CL=3 and STARTBURST_DEL disabled bit31=0 +# bit27-24: 6= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM +# bit30-28: 3 required +# bit31: 0=no additional STARTBURST delay + +DATA 0xFFD01408 0x2302544B # DDR Timing (Low) (active cycles value +1) +# bit3-0: TRAS lsbs +# bit7-4: TRCD +# bit11- 8: TRP +# bit15-12: TWR +# bit19-16: TWTR +# bit20: TRAS msb +# bit23-21: 0x0 +# bit27-24: TRRD +# bit31-28: TRTP + +DATA 0xFFD0140C 0x00000032 # DDR Timing (High) +# bit6-0: TRFC +# bit8-7: TR2R +# bit10-9: TR2W +# bit12-11: TW2W +# bit31-13: zero required + +DATA 0xFFD01410 0x0000000D # DDR Address Control +# bit1-0: 01, Cs0width=x16 +# bit3-2: 11, Cs0size=1Gb +# bit5-4: 00, Cs2width=nonexistent +# bit7-6: 00, Cs1size =nonexistent +# bit9-8: 00, Cs2width=nonexistent +# bit11-10: 00, Cs2size =nonexistent +# bit13-12: 00, Cs3width=nonexistent +# bit15-14: 00, Cs3size =nonexistent +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0 required + +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control +# bit0: 0, OpenPage enabled +# bit31-1: 0 required + +DATA 0xFFD01418 0x00000000 # DDR Operation +# bit3-0: 0x0, DDR cmd +# bit31-4: 0 required + +DATA 0xFFD0141C 0x00000642 # DDR Mode +DATA 0xFFD01420 0x00000040 # DDR Extended Mode +# bit0: 0, DDR DLL enabled +# bit1: 0, DDR drive strenght normal +# bit2: 1, DDR ODT control lsd disabled +# bit5-3: 000, required +# bit6: 1, DDR ODT control msb, enabled +# bit9-7: 000, required +# bit10: 0, differential DQS enabled +# bit11: 0, required +# bit12: 0, DDR output buffer enabled +# bit31-13: 0 required + +DATA 0xFFD01424 0x0000F07F # DDR Controller Control High +# bit2-0: 111, required +# bit3 : 1 , MBUS Burst Chop disabled +# bit6-4: 111, required +# bit7 : 0 +# bit8 : 0 , no sample stage +# bit9 : 0 , no half clock cycle addition to dataout +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh +# bit15-12: 1111 required +# bit31-16: 0 required + +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 +DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 00, CS0 hit selected +# bit23-4: ones, required +# bit31-24: 0x07, Size (i.e. 128MB) + +DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xFFD01494 0x00000000 # DDR ODT Control (Low) +# bit3-0: 0, ODT0Rd, MODT[0] asserted during read from DRAM CS0 +# bit19-16:0, ODT0Wr, MODT[0] asserted during write to DRAM CS0 + +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) +# bit1-0: 00, ODT0 controlled by ODT Control (low) register above +# bit3-2: 00, ODT1 controlled by register +# bit31-4: zero, required + +DATA 0xFFD0149C 0x0000E90F # CPU ODT Control +# bit3-0: F, ODT0Rd, Internal ODT asserted during read from DRAM bank0 +# bit7-4: 0, ODT0Wr, Internal ODT asserted during write to DRAM bank0 +# bit9-8: 1, ODTEn, never active +# bit11-10:2, DQ_ODTSel. ODT select turned on, 75 ohm + +DATA 0xFFD01480 0x00000001 # DDR Initialization Control +#bit0=1, enable DDR init upon this register write + +# End of Header extension +DATA 0x0 0x0 |