diff options
Diffstat (limited to 'board')
-rw-r--r-- | board/freescale/mx6qsabreauto/mx6qsabreauto.c | 36 | ||||
-rw-r--r-- | board/freescale/mx6sabresd/mx6sabresd.c | 36 | ||||
-rw-r--r-- | board/freescale/mx6slevk/mx6slevk.c | 35 | ||||
-rw-r--r-- | board/freescale/mx6sx_17x17_arm2/mx6sx_17x17_arm2.c | 36 | ||||
-rw-r--r-- | board/freescale/mx6sx_19x19_arm2/mx6sx_19x19_arm2.c | 35 | ||||
-rw-r--r-- | board/freescale/mx6sxsabresd/mx6sxsabresd.c | 35 |
6 files changed, 213 insertions, 0 deletions
diff --git a/board/freescale/mx6qsabreauto/mx6qsabreauto.c b/board/freescale/mx6qsabreauto/mx6qsabreauto.c index 9779d38..ca2b290 100644 --- a/board/freescale/mx6qsabreauto/mx6qsabreauto.c +++ b/board/freescale/mx6qsabreauto/mx6qsabreauto.c @@ -186,6 +186,37 @@ iomux_v3_cfg_t const usdhc3_pads[] = { }; #ifdef CONFIG_SYS_I2C_MXC +/* set all switches APS in normal and PFM mode in standby */ +static int setup_pmic_mode(int chip) +{ + unsigned char offset, i, switch_num, value; + + if (!chip) { + /* pfuze100 */ + switch_num = 6; + offset = 0x31; + } else { + /* pfuze200 */ + switch_num = 4; + offset = 0x38; + } + + value = 0xc; + if (i2c_write(0x8, 0x23, 1, &value, 1)) { + printf("Set SW1AB mode error!\n"); + return -1; + } + + for (i = 0; i < switch_num - 1; i++) { + if (i2c_write(0x8, offset + i * 7, 1, &value, 1)) { + printf("Set switch%x mode error!\n", offset); + return -1; + } + } + + return 0; +} + static int setup_pmic_voltages(void) { unsigned char value, rev_id = 0 ; @@ -200,6 +231,11 @@ static int setup_pmic_voltages(void) return -1; } printf("Found PFUZE100! deviceid=%x,revid=%x\n", value, rev_id); + + if (setup_pmic_mode(value & 0xf)) { + printf("setup pmic mode error!\n"); + return -1; + } /* set SW1AB staby volatage 0.975V*/ if (i2c_read(0x8, 0x21, 1, &value, 1)) { printf("Read SW1ABSTBY error!\n"); diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c index 27a6993..4111e0d 100644 --- a/board/freescale/mx6sabresd/mx6sabresd.c +++ b/board/freescale/mx6sabresd/mx6sabresd.c @@ -253,6 +253,37 @@ static void setup_iomux_uart(void) } #ifdef CONFIG_SYS_I2C_MXC +/* set all switches APS in normal and PFM mode in standby */ +static int setup_pmic_mode(int chip) +{ + unsigned char offset, i, switch_num, value; + + if (!chip) { + /* pfuze100 */ + switch_num = 6; + offset = 0x31; + } else { + /* pfuze200 */ + switch_num = 4; + offset = 0x38; + } + + value = 0xc; + if (i2c_write(0x8, 0x23, 1, &value, 1)) { + printf("Set SW1AB mode error!\n"); + return -1; + } + + for (i = 0; i < switch_num - 1; i++) { + if (i2c_write(0x8, offset + i * 7, 1, &value, 1)) { + printf("Set switch%x mode error!\n", offset); + return -1; + } + } + + return 0; +} + static int setup_pmic_voltages(void) { unsigned char value, rev_id = 0 ; @@ -269,6 +300,11 @@ static int setup_pmic_voltages(void) } printf("Found PFUZE%s deviceid=%x,revid=%x\n", ((value & 0xf) == 0) ? "100" : "200", value, rev_id); + + if (setup_pmic_mode(value & 0xf)) { + printf("setup pmic mode error!\n"); + return -1; + } /*For camera streaks issue,swap VGEN5 and VGEN3 to power camera. *sperate VDDHIGH_IN and camera 2.8V power supply, after switch: *VGEN5 for VDDHIGH_IN and increase to 3V to align with datasheet diff --git a/board/freescale/mx6slevk/mx6slevk.c b/board/freescale/mx6slevk/mx6slevk.c index 7df58fc..752dad8 100644 --- a/board/freescale/mx6slevk/mx6slevk.c +++ b/board/freescale/mx6slevk/mx6slevk.c @@ -617,6 +617,37 @@ static int setup_fec(void) #endif #ifdef CONFIG_SYS_I2C_MXC +/* set all switches APS in normal and PFM mode in standby */ +static int setup_pmic_mode(int chip) +{ + unsigned char offset, i, switch_num, value; + + if (!chip) { + /* pfuze100 */ + switch_num = 6; + offset = 0x31; + } else { + /* pfuze200 */ + switch_num = 4; + offset = 0x38; + } + + value = 0xc; + if (i2c_write(0x8, 0x23, 1, &value, 1)) { + printf("Set SW1AB mode error!\n"); + return -1; + } + + for (i = 0; i < switch_num - 1; i++) { + if (i2c_write(0x8, offset + i * 7, 1, &value, 1)) { + printf("Set switch%x mode error!\n", offset); + return -1; + } + } + + return 0; +} + static int setup_pmic_voltages(void) { unsigned char value, rev_id = 0; @@ -634,6 +665,10 @@ static int setup_pmic_voltages(void) printf("Found PFUZE%s deviceid=%x,revid=%x\n", ((value & 0xf) == 0) ? "100" : "200", value, rev_id); + if (setup_pmic_mode(value & 0xf)) { + printf("setup pmic mode error!\n"); + return -1; + } /* set SW1AB staby volatage 0.975V */ if (i2c_read(0x8, 0x21, 1, &value, 1)) { printf("Read SW1ABSTBY error!\n"); diff --git a/board/freescale/mx6sx_17x17_arm2/mx6sx_17x17_arm2.c b/board/freescale/mx6sx_17x17_arm2/mx6sx_17x17_arm2.c index 6a9788b..703db49 100644 --- a/board/freescale/mx6sx_17x17_arm2/mx6sx_17x17_arm2.c +++ b/board/freescale/mx6sx_17x17_arm2/mx6sx_17x17_arm2.c @@ -499,6 +499,38 @@ int board_phy_config(struct phy_device *phydev) #define PFUZE100_SW1CSTBY 0x2f #define PFUZE100_SW1CCONF 0x32 #define PFUZE100_SW1ABC_SETP(x) ((x-3000)/250) + +/* set all switches APS in normal and PFM mode in standby */ +static int setup_pmic_mode(int chip) +{ + unsigned char offset, i, switch_num, value; + + if (!chip) { + /* pfuze100 */ + switch_num = 6; + offset = 0x31; + } else { + /* pfuze200 */ + switch_num = 4; + offset = 0x38; + } + + value = 0xc; + if (i2c_write(0x8, 0x23, 1, &value, 1)) { + printf("Set SW1AB mode error!\n"); + return -1; + } + + for (i = 0; i < switch_num - 1; i++) { + if (i2c_write(0x8, offset + i * 7, 1, &value, 1)) { + printf("Set switch%x mode error!\n", offset); + return -1; + } + } + + return 0; +} + static int setup_pmic_voltages(void) { unsigned char value, rev_id = 0; @@ -516,6 +548,10 @@ static int setup_pmic_voltages(void) } printf("Found PFUZE100! deviceid 0x%x, revid 0x%x\n", value, rev_id); + if (setup_pmic_mode(value & 0xf)) { + printf("setup pmic mode error!\n"); + return -1; + } /* set SW1AB staby volatage 0.975V */ if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1ABSTBY, 1, &value, 1)) { printf("Read SW1ABSTBY error!\n"); diff --git a/board/freescale/mx6sx_19x19_arm2/mx6sx_19x19_arm2.c b/board/freescale/mx6sx_19x19_arm2/mx6sx_19x19_arm2.c index cd0a293..0b29b8c 100644 --- a/board/freescale/mx6sx_19x19_arm2/mx6sx_19x19_arm2.c +++ b/board/freescale/mx6sx_19x19_arm2/mx6sx_19x19_arm2.c @@ -616,6 +616,37 @@ int board_phy_config(struct phy_device *phydev) #define PFUZE100_SW1CCONF 0x32 #define PFUZE100_SW1ABC_SETP(x) ((x-3000)/250) +/* set all switches APS in normal and PFM mode in standby */ +static int setup_pmic_mode(int chip) +{ + unsigned char offset, i, switch_num, value; + + if (!chip) { + /* pfuze100 */ + switch_num = 6; + offset = 0x31; + } else { + /* pfuze200 */ + switch_num = 4; + offset = 0x38; + } + + value = 0xc; + if (i2c_write(0x8, 0x23, 1, &value, 1)) { + printf("Set SW1AB mode error!\n"); + return -1; + } + + for (i = 0; i < switch_num - 1; i++) { + if (i2c_write(0x8, offset + i * 7, 1, &value, 1)) { + printf("Set switch%x mode error!\n", offset); + return -1; + } + } + + return 0; +} + static int setup_pmic_voltages(void) { unsigned char value, rev_id = 0; @@ -634,6 +665,10 @@ static int setup_pmic_voltages(void) printf("Found PFUZE%s deviceid=%x,revid=%x\n", ((value & 0xf) == 0) ? "100" : "200", value, rev_id); + if (setup_pmic_mode(value & 0xf)) { + printf("setup pmic mode error!\n"); + return -1; + } /* set SW1AB staby volatage 0.975V */ if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1ABSTBY, 1, &value, 1)) { printf("Read SW1ABSTBY error!\n"); diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c b/board/freescale/mx6sxsabresd/mx6sxsabresd.c index 9c785e0..c0f35f3 100644 --- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c +++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c @@ -625,6 +625,37 @@ int board_phy_config(struct phy_device *phydev) #define PFUZE100_SW1ABC_SETP(x) ((x - 3000) / 250) #define PFUZE100_VGEN5CTL 0x70 +/* set all switches APS in normal and PFM mode in standby */ +static int setup_pmic_mode(int chip) +{ + unsigned char offset, i, switch_num, value; + + if (!chip) { + /* pfuze100 */ + switch_num = 6; + offset = 0x31; + } else { + /* pfuze200 */ + switch_num = 4; + offset = 0x38; + } + + value = 0xc; + if (i2c_write(0x8, 0x23, 1, &value, 1)) { + printf("Set SW1AB mode error!\n"); + return -1; + } + + for (i = 0; i < switch_num - 1; i++) { + if (i2c_write(0x8, offset + i * 7, 1, &value, 1)) { + printf("Set switch%x mode error!\n", offset); + return -1; + } + } + + return 0; +} + static int setup_pmic_voltages(void) { unsigned char value, rev_id = 0; @@ -643,6 +674,10 @@ static int setup_pmic_voltages(void) } printf("Found PFUZE100! deviceid 0x%x, revid 0x%x\n", value, rev_id); + if (setup_pmic_mode(value & 0xf)) { + printf("setup pmic mode error!\n"); + return -1; + } /* set SW1AB standby volatage 0.975V */ if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1ABSTBY, 1, &value, 1)) { printf("Read SW1ABSTBY error!\n"); |