diff options
Diffstat (limited to 'board')
| -rw-r--r-- | board/freescale/mx6q_hdmidongle/mx6q_hdmidongle.c | 49 |
1 files changed, 29 insertions, 20 deletions
diff --git a/board/freescale/mx6q_hdmidongle/mx6q_hdmidongle.c b/board/freescale/mx6q_hdmidongle/mx6q_hdmidongle.c index 6cfe334..34edc04 100644 --- a/board/freescale/mx6q_hdmidongle/mx6q_hdmidongle.c +++ b/board/freescale/mx6q_hdmidongle/mx6q_hdmidongle.c @@ -1,5 +1,5 @@ /* - * Copyright (C) 2012 Freescale Semiconductor, Inc. + * Copyright (C) 2012-2013 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -213,17 +213,29 @@ void board_mmu_init(void) } #endif -#ifdef CONFIG_DWC_AHSATA - #define ANATOP_PLL_LOCK 0x80000000 #define ANATOP_PLL_ENABLE_MASK 0x00002000 #define ANATOP_PLL_BYPASS_MASK 0x00010000 -#define ANATOP_PLL_LOCK 0x80000000 #define ANATOP_PLL_PWDN_MASK 0x00001000 #define ANATOP_PLL_HOLD_RING_OFF_MASK 0x00000800 #define ANATOP_SATA_CLK_ENABLE_MASK 0x00100000 +#define PORT_PHY_CTL 0x178 +#define PORT_PHY_CTL_PDDQ_LOC 0x100000 + +/* Note: udelay() is not accurate for i2c timing */ +static void __udelay(int time) +{ + int i, j; + + for (i = 0; i < time; i++) { + for (j = 0; j < 200; j++) { + asm("nop"); + asm("nop"); + } + } +} -int setup_sata(void) +static int setup_sata(void) { u32 reg = 0; s32 timeout = 100000; @@ -266,10 +278,19 @@ int setup_sata(void) * */ reg |= 0x59124c6; writel(reg, IOMUXC_BASE_ADDR + 0x34); + /* FIXME */ + /* + * It needs to wait SATA PHY initialize completed, otherwise write the + * PORT_PHY_CTL will fail, then can't enable PDDQ which let PHY entry LPM + * Currently set it as 1ms. + */ + __udelay(1000); + /* Enable PDDQ mode in default */ + writel(readl(SATA_ARB_BASE_ADDR + PORT_PHY_CTL) | PORT_PHY_CTL_PDDQ_LOC, + SATA_ARB_BASE_ADDR + PORT_PHY_CTL); return 0; } -#endif int dram_init(void) { @@ -404,18 +425,7 @@ static void setup_i2c(unsigned int module_base) break; } } -/* Note: udelay() is not accurate for i2c timing */ -static void __udelay(int time) -{ - int i, j; - for (i = 0; i < time; i++) { - for (j = 0; j < 200; j++) { - asm("nop"); - asm("nop"); - } - } -} static void mx6q_i2c_gpio_scl_direction(int bus, int output) { u32 reg; @@ -1193,10 +1203,7 @@ int board_init(void) gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; setup_uart(); - -#ifdef CONFIG_DWC_AHSATA setup_sata(); -#endif #ifdef CONFIG_VIDEO_MX5 /* Enable lvds power */ @@ -1427,6 +1434,8 @@ int checkboard(void) printf("UNKNOWN\n"); break; } + printf("SATA PDDQ: %s\n", ((readl(SATA_ARB_BASE_ADDR + PORT_PHY_CTL) + & PORT_PHY_CTL_PDDQ_LOC)>>20) ? "enabled" : "disabled"); return 0; } |