diff options
Diffstat (limited to 'board')
79 files changed, 2392 insertions, 1571 deletions
diff --git a/board/actux1/Makefile b/board/actux1/Makefile deleted file mode 100644 index 05a8669..0000000 --- a/board/actux1/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := actux1.o diff --git a/board/actux1/actux1.c b/board/actux1/actux1.c deleted file mode 100644 index 03ccd93..0000000 --- a/board/actux1/actux1.c +++ /dev/null @@ -1,148 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * (C) Copyright 2006 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * (C) Copyright 2002 - * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger <mgroeger@sysgo.de> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <command.h> -#include <malloc.h> -#include <asm/arch/ixp425.h> -#include <asm/io.h> -#include <miiphy.h> -#ifdef CONFIG_PCI -#include <pci.h> -#include <asm/arch/ixp425pci.h> -#endif - -#include "actux1_hw.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - /* CS5: Debug port */ - writel(0x9d520003, IXP425_EXP_CS5); - /* CS6: HwRel */ - writel(0x81860001, IXP425_EXP_CS6); - /* CS7: LEDs */ - writel(0x80900003, IXP425_EXP_CS7); - return 0; -} - -int board_init(void) -{ - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x00000100; - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST); - - /* Setup GPIOs for PCI INTA */ - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI1_INTA); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI1_INTA); - - /* Setup GPIOs for 33MHz clock output */ - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK); - writel(0x011001FF, IXP425_GPIO_GPCLKR); - - udelay(533); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST); - - ACTUX1_LED1(2); - ACTUX1_LED2(2); - ACTUX1_LED3(0); - ACTUX1_LED4(0); - ACTUX1_LED5(0); - ACTUX1_LED6(0); - ACTUX1_LED7(0); - - ACTUX1_HS(ACTUX1_HS_DCD); - - return 0; -} - -/* - * Check Board Identity - */ -int checkboard(void) -{ - char buf[64]; - int i = getenv_f("serial#", buf, sizeof(buf)); - - puts("Board: AcTux-1 rev."); - putc(ACTUX1_BOARDREL + 'A' - 1); - - if (i > 0) { - puts(", serial# "); - puts(buf); - } - putc('\n'); - - return 0; -} - -/************************************************************************* - * get_board_rev() - setup to pass kernel board revision information - * 0 = reserved - * 1 = Rev. A - * 2 = Rev. B - *************************************************************************/ -u32 get_board_rev(void) -{ - return ACTUX1_BOARDREL; -} - -int dram_init(void) -{ - gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20); - return 0; -} - - -#ifdef CONFIG_PCI -struct pci_controller hose; - -void pci_init_board(void) -{ - pci_ixp_init(&hose); -} -#endif - -void reset_phy(void) -{ - u16 id1, id2; - - /* initialize the PHY */ - miiphy_reset("NPE0", CONFIG_PHY_ADDR); - - miiphy_read("NPE0", CONFIG_PHY_ADDR, MII_PHYSID1, &id1); - miiphy_read("NPE0", CONFIG_PHY_ADDR, MII_PHYSID2, &id2); - - id2 &= 0xFFF0; /* mask out revision bits */ - - if (id1 == 0x13 && id2 == 0x78e0) { - /* - * LXT971/LXT972 PHY: set LED outputs: - * LED1(green) = Link/ACT, - * LED2 (unused) = LINK, - * LED3(red) = Coll - */ - miiphy_write("NPE0", CONFIG_PHY_ADDR, 20, 0xD432); - } else if (id1 == 0x143 && id2 == 0xbc30) { - /* BCM5241: default values are OK */ - } else - printf("unknown ethernet PHY ID: %x %x\n", id1, id2); -} diff --git a/board/actux1/actux1_hw.h b/board/actux1/actux1_hw.h deleted file mode 100644 index 5627f24..0000000 --- a/board/actux1/actux1_hw.h +++ /dev/null @@ -1,41 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * hardware register definitions for the AcTux-1 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _ACTUX1_HW_H -#define _ACTUX1_HW_H - -/* 0 = LED off,1 = green, 2 = red, 3 = orange */ -#define ACTUX1_LED1(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 0) -#define ACTUX1_LED2(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 1) -#define ACTUX1_LED3(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 2) -#define ACTUX1_LED4(a) writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 3) -#define ACTUX1_LED5(a) writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 4) -#define ACTUX1_LED6(a) writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 5) -#define ACTUX1_LED7(a) writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 6) -#define ACTUX1_HS(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 7) -#define ACTUX1_HS_DCD 0x01 -#define ACTUX1_HS_DSR 0x02 - -#define ACTUX1_DBG_PORT IXP425_EXP_BUS_CS5_BASE_PHYS -#define ACTUX1_BOARDREL (readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0x0F) - -/* GPIO settings */ -#define CONFIG_SYS_GPIO_PCI1_INTA 2 -#define CONFIG_SYS_GPIO_PCI2_INTA 3 -#define CONFIG_SYS_GPIO_I2C_SDA 4 -#define CONFIG_SYS_GPIO_I2C_SCL 5 -#define CONFIG_SYS_GPIO_DBGJUMPER 9 -#define CONFIG_SYS_GPIO_BUTTON1 10 -#define CONFIG_SYS_GPIO_DBGSENSE 11 -#define CONFIG_SYS_GPIO_DTR 12 -#define CONFIG_SYS_GPIO_IORST 13 /* Out */ -#define CONFIG_SYS_GPIO_PCI_CLK 14 /* Out */ -#define CONFIG_SYS_GPIO_EXTBUS_CLK 15 /* Out */ - -#endif diff --git a/board/actux1/u-boot.lds b/board/actux1/u-boot.lds deleted file mode 100644 index 4716e4f..0000000 --- a/board/actux1/u-boot.lds +++ /dev/null @@ -1,99 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_FORMAT ("elf32-bigarm", "elf32-bigarm", "elf32-bigarm") -OUTPUT_ARCH (arm) -ENTRY (_start) -SECTIONS -{ - . = 0x00000000; - - . = ALIGN (4); - .text : { - *(.__image_copy_start) - arch/arm/cpu/ixp/start.o(.text*) - net/built-in.o(.text*) - board/actux1/built-in.o(.text*) - arch/arm/cpu/ixp/built-in.o(.text*) - drivers/input/built-in.o(.text*) - - . = env_offset; - common/env_embedded.o(.ppcenv) - *(.text*) - } - - . = ALIGN(4); - .rodata : { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - } - . = ALIGN(4); - .data : { - *(.data*) - } - . = ALIGN(4); - .got : { - *(.got) - } - . =.; - - . = ALIGN(4); - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } - - . = ALIGN (4); - - .image_copy_end : - { - *(.__image_copy_end) - } - - .rel_dyn_start : - { - *(.__rel_dyn_start) - } - - .rel.dyn : { - *(.rel*) - } - - .rel_dyn_end : - { - *(.__rel_dyn_end) - } - - _end = .; - -/* - * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c - * __bss_base and __bss_limit are for linker only (overlay ordering) - */ - - .bss_start __rel_dyn_start (OVERLAY) : { - KEEP(*(.__bss_start)); - __bss_base = .; - } - - .bss __bss_base (OVERLAY) : { - *(.bss*) - . = ALIGN(4); - __bss_limit = .; - } - .bss_end __bss_limit (OVERLAY) : { - KEEP(*(.__bss_end)); - } - - .dynsym _end : { *(.dynsym) } - .dynbss : { *(.dynbss) } - .dynstr : { *(.dynstr*) } - .dynamic : { *(.dynamic*) } - .hash : { *(.hash*) } - .plt : { *(.plt*) } - .interp : { *(.interp*) } - .gnu : { *(.gnu*) } - .ARM.exidx : { *(.ARM.exidx*) } -} diff --git a/board/actux2/Makefile b/board/actux2/Makefile deleted file mode 100644 index 24cbff1..0000000 --- a/board/actux2/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := actux2.o diff --git a/board/actux2/actux2.c b/board/actux2/actux2.c deleted file mode 100644 index e578cd0..0000000 --- a/board/actux2/actux2.c +++ /dev/null @@ -1,122 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * (C) Copyright 2006 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * (C) Copyright 2002 - * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger <mgroeger@sysgo.de> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <command.h> -#include <malloc.h> -#include <asm/arch/ixp425.h> -#include <asm/io.h> - -#include <miiphy.h> - -#include "actux2_hw.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - /* CS1: IPAC-X */ - writel(0x94d10013, IXP425_EXP_CS1); - /* CS5: Debug port */ - writel(0x9d520003, IXP425_EXP_CS5); - /* CS6: HW release register */ - writel(0x81860001, IXP425_EXP_CS6); - /* CS7: LEDs */ - writel(0x80900003, IXP425_EXP_CS7); - - return 0; -} - -int board_init(void) -{ - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x00000100; - - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_ETHRST); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DSR); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DCD); - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_ETHRST); - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_DSR); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_DCD); - - /* Setup GPIOs for Interrupt inputs */ - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_DBGINT); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_ETHINT); - - /* Setup GPIOs for 33MHz clock output */ - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK); - writel(0x011001FF, IXP425_GPIO_GPCLKR); - - udelay(533); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_ETHRST); - - ACTUX2_LED1(1); - ACTUX2_LED2(0); - ACTUX2_LED3(0); - ACTUX2_LED4(0); - - return 0; -} - -/* - * Check Board Identity - */ -int checkboard(void) -{ - char buf[64]; - int i = getenv_f("serial#", buf, sizeof(buf)); - - puts("Board: AcTux-2 rev."); - putc(ACTUX2_BOARDREL + 'A' - 1); - - if (i > 0) { - puts(", serial# "); - puts(buf); - } - putc('\n'); - - return 0; -} - -int dram_init(void) -{ - gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20); - return 0; -} - -/************************************************************************* - * get_board_rev() - setup to pass kernel board revision information - * 0 = reserved - * 1 = Rev. A - * 2 = Rev. B - *************************************************************************/ -u32 get_board_rev(void) -{ - return ACTUX2_BOARDREL; -} - -void reset_phy(void) -{ - /* init IcPlus IP175C ethernet switch to native IP175C mode */ - miiphy_write("NPE0", 29, 31, 0x175C); -} diff --git a/board/actux2/actux2_hw.h b/board/actux2/actux2_hw.h deleted file mode 100644 index 57c6fa7..0000000 --- a/board/actux2/actux2_hw.h +++ /dev/null @@ -1,43 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * hardware register definitions for the AcTux-2 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _ACTUX2_HW_H -#define _ACTUX2_HW_H - -/* 0 = LED off,1 = green, 2 = red, 3 = orange */ -#define ACTUX2_LED1(a) writeb((a ? 2 : 0), IXP425_EXP_BUS_CS7_BASE_PHYS + 0) -#define ACTUX2_LED2(a) writeb((a ? 2 : 0), IXP425_EXP_BUS_CS7_BASE_PHYS + 1) -#define ACTUX2_LED3(a) writeb((a ? 0 : 2), IXP425_EXP_BUS_CS7_BASE_PHYS + 2) -#define ACTUX2_LED4(a) writeb((a ? 0 : 2), IXP425_EXP_BUS_CS7_BASE_PHYS + 3) - -#define ACTUX2_DBG_PORT IXP425_EXP_BUS_CS5_BASE_PHYS -#define ACTUX2_BOARDREL (readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0x0F) -#define ACTUX2_OPTION (readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0xF0) - -/* - * GPIO settings - */ -#define CONFIG_SYS_GPIO_DBGINT 0 -#define CONFIG_SYS_GPIO_ETHINT 1 -#define CONFIG_SYS_GPIO_ETHRST 2 /* Out */ -#define CONFIG_SYS_GPIO_LED5_GN 3 /* Out */ -#define CONFIG_SYS_GPIO_UNUSED4 4 -#define CONFIG_SYS_GPIO_UNUSED5 5 -#define CONFIG_SYS_GPIO_DSR 6 /* Out */ -#define CONFIG_SYS_GPIO_DCD 7 /* Out */ -#define CONFIG_SYS_GPIO_IPAC_INT 8 -#define CONFIG_SYS_GPIO_DBGJUMPER 9 -#define CONFIG_SYS_GPIO_BUTTON1 10 -#define CONFIG_SYS_GPIO_DBGSENSE 11 -#define CONFIG_SYS_GPIO_DTR 12 -#define CONFIG_SYS_GPIO_IORST 13 /* Out */ -#define CONFIG_SYS_GPIO_PCI_CLK 14 /* Out */ -#define CONFIG_SYS_GPIO_EXTBUS_CLK 15 /* Out */ - -#endif diff --git a/board/actux2/u-boot.lds b/board/actux2/u-boot.lds deleted file mode 100644 index f00d7c7..0000000 --- a/board/actux2/u-boot.lds +++ /dev/null @@ -1,99 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_FORMAT ("elf32-bigarm", "elf32-bigarm", "elf32-bigarm") -OUTPUT_ARCH (arm) -ENTRY (_start) -SECTIONS -{ - . = 0x00000000; - - . = ALIGN (4); - .text : { - *(.__image_copy_start) - arch/arm/cpu/ixp/start.o(.text*) - net/built-in.o(.text*) - board/actux2/built-in.o(.text*) - arch/arm/cpu/ixp/built-in.o(.text*) - drivers/input/built-in.o(.text*) - - . = env_offset; - common/env_embedded.o(.ppcenv) - *(.text*) - } - - . = ALIGN(4); - .rodata : { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - } - . = ALIGN(4); - .data : { - *(.data*) - } - . = ALIGN(4); - .got : { - *(.got) - } - . =.; - - . = ALIGN(4); - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } - - . = ALIGN (4); - - .image_copy_end : - { - *(.__image_copy_end) - } - - .rel_dyn_start : - { - *(.__rel_dyn_start) - } - - .rel.dyn : { - *(.rel*) - } - - .rel_dyn_end : - { - *(.__rel_dyn_end) - } - - _end = .; - -/* - * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c - * __bss_base and __bss_limit are for linker only (overlay ordering) - */ - - .bss_start __rel_dyn_start (OVERLAY) : { - KEEP(*(.__bss_start)); - __bss_base = .; - } - - .bss __bss_base (OVERLAY) : { - *(.bss*) - . = ALIGN(4); - __bss_limit = .; - } - .bss_end __bss_limit (OVERLAY) : { - KEEP(*(.__bss_end)); - } - - .dynsym _end : { *(.dynsym) } - .dynbss : { *(.dynbss) } - .dynstr : { *(.dynstr*) } - .dynamic : { *(.dynamic*) } - .hash : { *(.hash*) } - .plt : { *(.plt*) } - .interp : { *(.interp*) } - .gnu : { *(.gnu*) } - .ARM.exidx : { *(.ARM.exidx*) } -} diff --git a/board/actux3/Makefile b/board/actux3/Makefile deleted file mode 100644 index f628f26..0000000 --- a/board/actux3/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := actux3.o diff --git a/board/actux3/actux3.c b/board/actux3/actux3.c deleted file mode 100644 index 09c803c..0000000 --- a/board/actux3/actux3.c +++ /dev/null @@ -1,149 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * (C) Copyright 2006 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * (C) Copyright 2002 - * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger <mgroeger@sysgo.de> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <command.h> -#include <malloc.h> -#include <asm/arch/ixp425.h> -#include <asm/io.h> -#include <miiphy.h> -#include "actux3_hw.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - /* CS1: IPAC-X */ - writel(0x94d10013, IXP425_EXP_CS1); - /* CS5: Debug port */ - writel(0x9d520003, IXP425_EXP_CS5); - /* CS6: Release/Option register */ - writel(0x81860001, IXP425_EXP_CS6); - /* CS7: LEDs */ - writel(0x80900003, IXP425_EXP_CS7); - - return 0; -} - -int board_init(void) -{ - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x00000100; - - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_ETHRST); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DSR); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DCD); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED5_GN); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED6_RT); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED6_GN); - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_ETHRST); - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_DSR); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_DCD); - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_LED5_GN); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_LED6_RT); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_LED6_GN); - - /* - * Setup GPIO's for Interrupt inputs - */ - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_DBGINT); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_ETHINT); - - /* - * Setup GPIO's for 33MHz clock output - */ - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK); - writel(0x011001FF, IXP425_GPIO_GPCLKR); - - /* we need a minimum PCI reset pulse width after enabling the clock */ - udelay(533); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_ETHRST); - - ACTUX3_LED1_RT(1); - ACTUX3_LED1_GN(0); - ACTUX3_LED2_RT(0); - ACTUX3_LED2_GN(0); - ACTUX3_LED3_RT(0); - ACTUX3_LED3_GN(0); - ACTUX3_LED4_GN(0); - ACTUX3_LED5_RT(0); - - return 0; -} - -/* - * Check Board Identity - */ -int checkboard(void) -{ - char buf[64]; - int i = getenv_f("serial#", buf, sizeof(buf)); - - puts("Board: AcTux-3 rev."); - putc(ACTUX3_BOARDREL + 'A' - 1); - - if (i > 0) { - puts (", serial# "); - puts (buf); - } - putc('\n'); - - return 0; -} - -/************************************************************************* - * get_board_rev() - setup to pass kernel board revision information - * 0 = reserved - * 1 = Rev. A - * 2 = Rev. B - *************************************************************************/ -u32 get_board_rev(void) -{ - return ACTUX3_BOARDREL; -} - -int dram_init(void) -{ - gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20); - return 0; -} - -void reset_phy(void) -{ - int i; - - /* initialize the PHY */ - miiphy_reset("NPE0", CONFIG_PHY_ADDR); - - /* all LED outputs = Link/Act */ - miiphy_write("NPE0", CONFIG_PHY_ADDR, 0x16, 0x0AAA); - - /* - * The Marvell 88E6060 switch comes up with all ports disabled. - * set all ethernet switch ports to forwarding state - */ - for (i = 1; i <= 5; i++) - miiphy_write("NPE0", CONFIG_PHY_ADDR + 8 + i, 0x04, 0x03); - -} diff --git a/board/actux3/actux3_hw.h b/board/actux3/actux3_hw.h deleted file mode 100644 index f8acb4d..0000000 --- a/board/actux3/actux3_hw.h +++ /dev/null @@ -1,44 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * hardware register definitions for the AcTux-3 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _ACTUX3_HW_H -#define _ACTUX3_HW_H - -/* 0 = LED off,1 = ON */ -#define ACTUX3_LED1_RT(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 0) -#define ACTUX3_LED1_GN(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 1) -#define ACTUX3_LED2_RT(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 2) -#define ACTUX3_LED2_GN(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 3) -#define ACTUX3_LED3_RT(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 4) -#define ACTUX3_LED3_GN(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 5) -#define ACTUX3_LED4_GN(a) writeb((a)^1, IXP425_EXP_BUS_CS7_BASE_PHYS + 6) -#define ACTUX3_LED5_RT(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 7) - -#define ACTUX3_DBG_PORT IXP425_EXP_BUS_CS5_BASE_PHYS -#define ACTUX3_BOARDREL (readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0x0F) -#define ACTUX3_OPTION (readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0xF0) - -/* GPIO settings */ -#define CONFIG_SYS_GPIO_DBGINT 0 -#define CONFIG_SYS_GPIO_ETHINT 1 -#define CONFIG_SYS_GPIO_ETHRST 2 /* Out */ -#define CONFIG_SYS_GPIO_LED5_GN 3 /* Out */ -#define CONFIG_SYS_GPIO_LED6_RT 4 /* Out */ -#define CONFIG_SYS_GPIO_LED6_GN 5 /* Out */ -#define CONFIG_SYS_GPIO_DSR 6 /* Out */ -#define CONFIG_SYS_GPIO_DCD 7 /* Out */ -#define CONFIG_SYS_GPIO_DBGJUMPER 9 -#define CONFIG_SYS_GPIO_BUTTON1 10 -#define CONFIG_SYS_GPIO_DBGSENSE 11 -#define CONFIG_SYS_GPIO_DTR 12 -#define CONFIG_SYS_GPIO_IORST 13 /* Out */ -#define CONFIG_SYS_GPIO_PCI_CLK 14 /* Out */ -#define CONFIG_SYS_GPIO_EXTBUS_CLK 15 /* Out */ - -#endif diff --git a/board/actux3/u-boot.lds b/board/actux3/u-boot.lds deleted file mode 100644 index 2de3ca6..0000000 --- a/board/actux3/u-boot.lds +++ /dev/null @@ -1,99 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_FORMAT ("elf32-bigarm", "elf32-bigarm", "elf32-bigarm") -OUTPUT_ARCH (arm) -ENTRY (_start) -SECTIONS -{ - . = 0x00000000; - - . = ALIGN (4); - .text : { - *(.__image_copy_start) - arch/arm/cpu/ixp/start.o(.text*) - net/built-in.o(.text*) - board/actux3/built-in.o(.text*) - arch/arm/cpu/ixp/built-in.o(.text*) - drivers/input/built-in.o(.text*) - - . = env_offset; - common/env_embedded.o(.ppcenv) - *(.text*) - } - - . = ALIGN(4); - .rodata : { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - } - . = ALIGN(4); - .data : { - *(.data*) - } - . = ALIGN(4); - .got : { - *(.got) - } - . =.; - - . = ALIGN(4); - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } - - . = ALIGN (4); - - .image_copy_end : - { - *(.__image_copy_end) - } - - .rel_dyn_start : - { - *(.__rel_dyn_start) - } - - .rel.dyn : { - *(.rel*) - } - - .rel_dyn_end : - { - *(.__rel_dyn_end) - } - - _end = .; - -/* - * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c - * __bss_base and __bss_limit are for linker only (overlay ordering) - */ - - .bss_start __rel_dyn_start (OVERLAY) : { - KEEP(*(.__bss_start)); - __bss_base = .; - } - - .bss __bss_base (OVERLAY) : { - *(.bss*) - . = ALIGN(4); - __bss_limit = .; - } - .bss_end __bss_limit (OVERLAY) : { - KEEP(*(.__bss_end)); - } - - .dynsym _end : { *(.dynsym) } - .dynbss : { *(.dynbss) } - .dynstr : { *(.dynstr*) } - .dynamic : { *(.dynamic*) } - .hash : { *(.hash*) } - .plt : { *(.plt*) } - .interp : { *(.interp*) } - .gnu : { *(.gnu*) } - .ARM.exidx : { *(.ARM.exidx*) } -} diff --git a/board/actux4/Makefile b/board/actux4/Makefile deleted file mode 100644 index b949b60..0000000 --- a/board/actux4/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := actux4.o diff --git a/board/actux4/actux4.c b/board/actux4/actux4.c deleted file mode 100644 index 81c5458..0000000 --- a/board/actux4/actux4.c +++ /dev/null @@ -1,129 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * (C) Copyright 2006 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * (C) Copyright 2002 - * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger <mgroeger@sysgo.de> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <command.h> -#include <malloc.h> -#include <asm/arch/ixp425.h> -#include <asm/io.h> -#include <miiphy.h> -#ifdef CONFIG_PCI -#include <pci.h> -#include <asm/arch/ixp425pci.h> -#endif - -#include "actux4_hw.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - writel(0xbd113c42, IXP425_EXP_CS1); - return 0; -} - -int board_init(void) -{ - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x00000100; - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_nPWRON); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_nPWRON); - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST); - - /* led not populated on board*/ - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED3); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED3); - - /* middle LED */ - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED2); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED2); - - /* right LED */ - /* weak pulldown = LED weak on */ - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_LED1); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED1); - - /* Setup GPIO's for Interrupt inputs */ - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTA); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTB); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTC); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_RTCINT); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTA); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTB); - - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTA); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTB); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTC); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_RTCINT); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTA); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTB); - - /* Setup GPIO's for 33MHz clock output */ - writel(0x011001FF, IXP425_GPIO_GPCLKR); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK); - - udelay(10000); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST); - udelay(10000); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST); - udelay(10000); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST); - - return 0; -} - -/* Check Board Identity */ -int checkboard(void) -{ - puts("Board: AcTux-4\n"); - return 0; -} - -int dram_init(void) -{ - gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20); - return 0; -} - -#ifdef CONFIG_PCI -struct pci_controller hose; - -void pci_init_board(void) -{ - pci_ixp_init(&hose); -} -#endif - -/* - * Hardcoded flash setup: - * Flash 0 is a non-CFI SST 39VF020 flash, 8 bit flash / 8 bit bus. - * Flash 1 is an Intel *16 flash using the CFI driver. - */ -ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info) -{ - if (banknum == 0) { /* non-CFI boot flash */ - info->portwidth = 1; - info->chipwidth = 1; - info->interface = FLASH_CFI_X8; - return 1; - } else - return 0; -} diff --git a/board/actux4/actux4_hw.h b/board/actux4/actux4_hw.h deleted file mode 100644 index b936376..0000000 --- a/board/actux4/actux4_hw.h +++ /dev/null @@ -1,33 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * hardware register definitions for the AcTux-4 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _ACTUX4_HW_H -#define _ACTUX4_HW_H - -/* - * GPIO settings - */ -#define CONFIG_SYS_GPIO_USBINTA 0 -#define CONFIG_SYS_GPIO_USBINTB 1 -#define CONFIG_SYS_GPIO_USBINTC 2 -#define CONFIG_SYS_GPIO_nPWRON 3 /* Out */ -#define CONFIG_SYS_GPIO_I2C_SCL 4 -#define CONFIG_SYS_GPIO_I2C_SDA 5 -#define CONFIG_SYS_GPIO_PCI_INTB 6 -#define CONFIG_SYS_GPIO_BUTTON1 7 -#define CONFIG_SYS_GPIO_LED1 8 /* Out */ -#define CONFIG_SYS_GPIO_RTCINT 9 -#define CONFIG_SYS_GPIO_LED2 10 /* Out */ -#define CONFIG_SYS_GPIO_PCI_INTA 11 -#define CONFIG_SYS_GPIO_IORST 12 /* Out */ -#define CONFIG_SYS_GPIO_LED3 13 /* Out */ -#define CONFIG_SYS_GPIO_PCI_CLK 14 /* Out */ -#define CONFIG_SYS_GPIO_EXTBUS_CLK 15 /* Out */ - -#endif diff --git a/board/altera/nios2-generic/nios2-generic.c b/board/altera/nios2-generic/nios2-generic.c index aa126d7..5ab9471 100644 --- a/board/altera/nios2-generic/nios2-generic.c +++ b/board/altera/nios2-generic/nios2-generic.c @@ -16,7 +16,8 @@ void text_base_hook(void); /* nop hook for text_base.S */ -#if defined(CONFIG_ENV_IS_IN_FLASH) && defined(CONFIG_ENV_ADDR) +#if defined(CONFIG_ENV_IS_IN_FLASH) && defined(CONFIG_ENV_ADDR) && \ + defined(CONFIG_CFI_FLASH_MTD) static void __early_flash_cmd_reset(void) { /* reset flash before we read env */ @@ -37,7 +38,8 @@ int board_early_init_f(void) "led"); #endif #endif -#if defined(CONFIG_ENV_IS_IN_FLASH) && defined(CONFIG_ENV_ADDR) +#if defined(CONFIG_ENV_IS_IN_FLASH) && defined(CONFIG_ENV_ADDR) && \ + defined(CONFIG_CFI_FLASH_MTD) early_flash_cmd_reset(); #endif return 0; diff --git a/board/bf609-ezkit/bf609-ezkit.c b/board/bf609-ezkit/bf609-ezkit.c index cfc64fe..43a4330 100644 --- a/board/bf609-ezkit/bf609-ezkit.c +++ b/board/bf609-ezkit/bf609-ezkit.c @@ -41,12 +41,12 @@ int board_eth_init(bd_t *bis) if (CONFIG_DW_PORTS & 1) { static const unsigned short pins[] = P_RMII0; if (!peripheral_request_list(pins, "emac0")) - ret += designware_initialize(0, EMAC0_MACCFG, 1, 0); + ret += designware_initialize(EMAC0_MACCFG, 0); } if (CONFIG_DW_PORTS & 2) { static const unsigned short pins[] = P_RMII1; if (!peripheral_request_list(pins, "emac1")) - ret += designware_initialize(1, EMAC1_MACCFG, 1, 0); + ret += designware_initialize(EMAC1_MACCFG, 0); } return ret; diff --git a/board/boundary/nitrogen6x/nitrogen6x.c b/board/boundary/nitrogen6x/nitrogen6x.c index 3f4cfa1..d9c05b0 100644 --- a/board/boundary/nitrogen6x/nitrogen6x.c +++ b/board/boundary/nitrogen6x/nitrogen6x.c @@ -389,7 +389,7 @@ int board_eth_init(bd_t *bis) } #endif -#ifdef CONFIG_MV_UDC +#ifdef CONFIG_CI_UDC /* For otg ethernet*/ usb_eth_initialize(bis); #endif diff --git a/board/dvlhost/Makefile b/board/dvlhost/Makefile deleted file mode 100644 index 8b48936..0000000 --- a/board/dvlhost/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := dvlhost.o watchdog.o diff --git a/board/dvlhost/dvlhost.c b/board/dvlhost/dvlhost.c deleted file mode 100644 index 087070f..0000000 --- a/board/dvlhost/dvlhost.c +++ /dev/null @@ -1,112 +0,0 @@ -/* - * (C) Copyright 2009 - * Michael Schwingen, michael@schwingen.org - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <config.h> -#include <command.h> -#include <malloc.h> -#include <asm/arch/ixp425.h> -#include <asm/io.h> -#include <miiphy.h> -#ifdef CONFIG_PCI -#include <pci.h> -#include <asm/arch/ixp425pci.h> -#endif - -#include "dvlhost_hw.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - /* CS1: LED Latch */ - writel(0xBFFF0002, IXP425_EXP_CS1); - return 0; -} - -int board_init(void) -{ - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x00000100; - - /* Setup GPIOs used as output */ - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_WDGTRIGGER); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_DLAN_PAIRING); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_PCIRST); - - /* - * LED latch enable and watchdog enable are tied to the same GPIO, - * so we need to trigger the watchdog if we want to enable the LEDs. - */ -#ifdef CONFIG_HW_WATCHDOG - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_WDG_LED_EN); -#else - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_WDG_LED_EN); -#endif - - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_WDGTRIGGER); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DLAN_PAIRING); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_WDG_LED_EN); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCIRST); - - /* Setup GPIOs for Interrupt inputs */ - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_BTN_WLAN); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_BTN_PAIRING); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_BTN_RESET); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_IRQA); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_IRQB); - - /* Setup GPIO's for 33MHz clock output */ - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK); - writel(0x01FF01FF, IXP425_GPIO_GPCLKR); - - /* turn off all LEDs */ - writew(0x0000, DVLHOST_LED_LATCH); - - udelay(533); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_PCIRST); - - return 0; -} - -/* Check Board Identity */ -int checkboard(void) -{ - char *s = getenv("serial#"); - - puts("Board: dLAN 200AV (dvlhost)"); - - if (s != NULL) { - puts(", serial# "); - puts(s); - } - putc('\n'); - - return 0; -} - -int dram_init(void) -{ - gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20); - return 0; -} - -#ifdef CONFIG_PCI -struct pci_controller hose; - -void pci_init_board(void) -{ - pci_ixp_init(&hose); -} -#endif - -void reset_phy(void) -{ - /* init IcPlus IP175C ethernet switch to native IP175C mode */ - miiphy_write("NPE1", 29, 31, 0x175C); -} diff --git a/board/dvlhost/dvlhost_hw.h b/board/dvlhost/dvlhost_hw.h deleted file mode 100644 index 545099e..0000000 --- a/board/dvlhost/dvlhost_hw.h +++ /dev/null @@ -1,31 +0,0 @@ -/* - * (C) Copyright 2009 - * Michael Schwingen, michael@schwingen.org - * - * hardware register definitions for the - * dLAN200 AV Wireless G ("dvlhost") board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _DVLHOST_HW_H -#define _DVLHOST_HW_H - -/* - * GPIO settings - */ -#define CONFIG_SYS_GPIO_WDGTRIGGER 0 /* Out */ -#define CONFIG_SYS_GPIO_BTN_WLAN 1 -#define CONFIG_SYS_GPIO_BTN_PAIRING 6 -#define CONFIG_SYS_GPIO_DLAN_PAIRING 7 /* Out */ -#define CONFIG_SYS_GPIO_BTN_RESET 9 -#define CONFIG_SYS_GPIO_IRQB 10 -#define CONFIG_SYS_GPIO_IRQA 11 -#define CONFIG_SYS_GPIO_WDG_LED_EN 12 /* Out */ -#define CONFIG_SYS_GPIO_PCIRST 13 /* Out */ -#define CONFIG_SYS_GPIO_PCI_CLK 14 /* Out */ -#define CONFIG_SYS_GPIO_EXTBUS_CLK 15 /* Out */ - -#define DVLHOST_LED_LATCH IXP425_EXP_BUS_CS1_BASE_PHYS - -#endif diff --git a/board/dvlhost/u-boot.lds b/board/dvlhost/u-boot.lds deleted file mode 100644 index ebcaf44..0000000 --- a/board/dvlhost/u-boot.lds +++ /dev/null @@ -1,99 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_FORMAT ("elf32-bigarm", "elf32-bigarm", "elf32-bigarm") -OUTPUT_ARCH (arm) -ENTRY (_start) -SECTIONS -{ - . = 0x00000000; - - . = ALIGN (4); - .text : { - *(.__image_copy_start) - arch/arm/cpu/ixp/start.o(.text*) - net/built-in.o(.text*) - board/dvlhost/built-in.o(.text*) - arch/arm/cpu/ixp/built-in.o(.text*) - drivers/serial/built-in.o(.text*) - - . = env_offset; - common/env_embedded.o(.ppcenv) - *(.text*) - } - - . = ALIGN (4); - .rodata : { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - } - . = ALIGN (4); - .data : { - *(.data*) - } - . = ALIGN (4); - .got : { - *(.got) - } - . =.; - - . = ALIGN(4); - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } - - . = ALIGN (4); - - .image_copy_end : - { - *(.__image_copy_end) - } - - .rel_dyn_start : - { - *(.__rel_dyn_start) - } - - .rel.dyn : { - *(.rel*) - } - - .rel_dyn_end : - { - *(.__rel_dyn_end) - } - - _end = .; - -/* - * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c - * __bss_base and __bss_limit are for linker only (overlay ordering) - */ - - .bss_start __rel_dyn_start (OVERLAY) : { - KEEP(*(.__bss_start)); - __bss_base = .; - } - - .bss __bss_base (OVERLAY) : { - *(.bss*) - . = ALIGN(4); - __bss_limit = .; - } - .bss_end __bss_limit (OVERLAY) : { - KEEP(*(.__bss_end)); - } - - .dynsym _end : { *(.dynsym) } - .dynbss : { *(.dynbss) } - .dynstr : { *(.dynstr*) } - .dynamic : { *(.dynamic*) } - .hash : { *(.hash*) } - .plt : { *(.plt*) } - .interp : { *(.interp*) } - .gnu : { *(.gnu*) } - .ARM.exidx : { *(.ARM.exidx*) } -} diff --git a/board/dvlhost/watchdog.c b/board/dvlhost/watchdog.c deleted file mode 100644 index 02ec35e..0000000 --- a/board/dvlhost/watchdog.c +++ /dev/null @@ -1,27 +0,0 @@ -/* - * (C) Copyright 2009 - * Michael Schwingen, michael@schwingen.org - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <config.h> -#include <asm/io.h> -#include "dvlhost_hw.h" - -DECLARE_GLOBAL_DATA_PTR; - -#ifdef CONFIG_HW_WATCHDOG -#include <watchdog.h> -#include <asm/arch/ixp425.h> - -void hw_watchdog_reset(void) -{ - unsigned int x; - x = readl(IXP425_GPIO_GPOUTR); - x ^= (1 << (CONFIG_SYS_GPIO_WDGTRIGGER)); - writel(x, IXP425_GPIO_GPOUTR); -} - -#endif /* CONFIG_HW_WATCHDOG */ diff --git a/board/freescale/t1040qds/Makefile b/board/freescale/t1040qds/Makefile index 93af9eb..c7470d7 100644 --- a/board/freescale/t1040qds/Makefile +++ b/board/freescale/t1040qds/Makefile @@ -9,3 +9,4 @@ obj-y += ddr.o obj-$(CONFIG_PCI) += pci.o obj-y += law.o obj-y += tlb.o +obj-y += eth.o diff --git a/board/freescale/t1040qds/README b/board/freescale/t1040qds/README index 6d380ae..8160ca0 100644 --- a/board/freescale/t1040qds/README +++ b/board/freescale/t1040qds/README @@ -121,14 +121,14 @@ NOR Flash memory Map on T1040QDS 0xEFF40000 0xEFFFFFFF u-boot (current bank) 768KB 0xEFF20000 0xEFF3FFFF u-boot env (current bank) 128KB 0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB -0xED300000 0xEFF3FFFF rootfs (alt bank) 44MB + 256KB -0xEC800000 0xEC8FFFF Hardware device tree (alt bank) 1MB +0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB +0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB 0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB 0xEC000000 0xEC01FFFF RCW (alt bank) 128KB 0xEBF40000 0xEBFFFFFF u-boot (alt bank) 768KB 0xEBF20000 0xEBF3FFFF u-boot env (alt bank) 128KB 0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB -0xE9300000 0xEBF3FFFF rootfs (current bank) 44MB + 256KB +0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB 0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 11MB + 512KB 0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB 0xE8000000 0xE801FFFF RCW (current bank) 128KB diff --git a/board/freescale/t1040qds/eth.c b/board/freescale/t1040qds/eth.c new file mode 100644 index 0000000..3077b4a --- /dev/null +++ b/board/freescale/t1040qds/eth.c @@ -0,0 +1,492 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * The RGMII PHYs are provided by the two on-board PHY connected to + * dTSEC instances 4 and 5. The SGMII PHYs are provided by one on-board + * PHY or by the standard four-port SGMII riser card (VSC). + */ + +#include <common.h> +#include <netdev.h> +#include <asm/fsl_serdes.h> +#include <asm/immap_85xx.h> +#include <fm_eth.h> +#include <fsl_mdio.h> +#include <malloc.h> +#include <asm/fsl_dtsec.h> + +#include "../common/fman.h" +#include "../common/qixis.h" + +#include "t1040qds_qixis.h" + +#ifdef CONFIG_FMAN_ENET + /* - In T1040 there are only 8 SERDES lanes, spread across 2 SERDES banks. + * Bank 1 -> Lanes A, B, C, D + * Bank 2 -> Lanes E, F, G, H + */ + + /* Mapping of 8 SERDES lanes to T1040 QDS board slots. A value of '0' here + * means that the mapping must be determined dynamically, or that the lane + * maps to something other than a board slot. + */ +static u8 lane_to_slot[] = { + 0, 0, 0, 0, 0, 0, 0, 0 +}; + +/* On the Vitesse VSC8234XHG SGMII riser card there are 4 SGMII PHYs + * housed. + */ +static int riser_phy_addr[] = { + CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR, + CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR, + CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR, + CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR, +}; + +/* Slot2 does not have EMI connections */ +#define EMI_NONE 0xFFFFFFFF +#define EMI1_RGMII0 0 +#define EMI1_RGMII1 1 +#define EMI1_SLOT1 2 +#define EMI1_SLOT3 3 +#define EMI1_SLOT4 4 +#define EMI1_SLOT5 5 +#define EMI1_SLOT6 6 +#define EMI1_SLOT7 7 +#define EMI2 8 + +static int mdio_mux[NUM_FM_PORTS]; + +static const char * const mdio_names[] = { + "T1040_QDS_MDIO0", + "T1040_QDS_MDIO1", + "T1040_QDS_MDIO2", + "T1040_QDS_MDIO3", + "T1040_QDS_MDIO4", + "T1040_QDS_MDIO5", + "T1040_QDS_MDIO6", + "T1040_QDS_MDIO7", +}; + +struct t1040_qds_mdio { + u8 muxval; + struct mii_dev *realbus; +}; + +static const char *t1040_qds_mdio_name_for_muxval(u8 muxval) +{ + return mdio_names[muxval]; +} + +struct mii_dev *mii_dev_for_muxval(u8 muxval) +{ + struct mii_dev *bus; + const char *name = t1040_qds_mdio_name_for_muxval(muxval); + + if (!name) { + printf("No bus for muxval %x\n", muxval); + return NULL; + } + + bus = miiphy_get_dev_by_name(name); + + if (!bus) { + printf("No bus by name %s\n", name); + return NULL; + } + + return bus; +} + +static void t1040_qds_mux_mdio(u8 muxval) +{ + u8 brdcfg4; + if (muxval <= 7) { + brdcfg4 = QIXIS_READ(brdcfg[4]); + brdcfg4 &= ~BRDCFG4_EMISEL_MASK; + brdcfg4 |= (muxval << BRDCFG4_EMISEL_SHIFT); + QIXIS_WRITE(brdcfg[4], brdcfg4); + } +} + +static int t1040_qds_mdio_read(struct mii_dev *bus, int addr, int devad, + int regnum) +{ + struct t1040_qds_mdio *priv = bus->priv; + + t1040_qds_mux_mdio(priv->muxval); + + return priv->realbus->read(priv->realbus, addr, devad, regnum); +} + +static int t1040_qds_mdio_write(struct mii_dev *bus, int addr, int devad, + int regnum, u16 value) +{ + struct t1040_qds_mdio *priv = bus->priv; + + t1040_qds_mux_mdio(priv->muxval); + + return priv->realbus->write(priv->realbus, addr, devad, regnum, value); +} + +static int t1040_qds_mdio_reset(struct mii_dev *bus) +{ + struct t1040_qds_mdio *priv = bus->priv; + + return priv->realbus->reset(priv->realbus); +} + +static int t1040_qds_mdio_init(char *realbusname, u8 muxval) +{ + struct t1040_qds_mdio *pmdio; + struct mii_dev *bus = mdio_alloc(); + + if (!bus) { + printf("Failed to allocate t1040_qds MDIO bus\n"); + return -1; + } + + pmdio = malloc(sizeof(*pmdio)); + if (!pmdio) { + printf("Failed to allocate t1040_qds private data\n"); + free(bus); + return -1; + } + + bus->read = t1040_qds_mdio_read; + bus->write = t1040_qds_mdio_write; + bus->reset = t1040_qds_mdio_reset; + sprintf(bus->name, t1040_qds_mdio_name_for_muxval(muxval)); + + pmdio->realbus = miiphy_get_dev_by_name(realbusname); + + if (!pmdio->realbus) { + printf("No bus with name %s\n", realbusname); + free(bus); + free(pmdio); + return -1; + } + + pmdio->muxval = muxval; + bus->priv = pmdio; + + return mdio_register(bus); +} + +/* + * Initialize the lane_to_slot[] array. + * + * On the T1040QDS board the mapping is controlled by ?? register. + */ +static void initialize_lane_to_slot(void) +{ + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + int serdes1_prtcl = (in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS1_PRTCL) + >> FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; + + QIXIS_WRITE(cms[0], 0x07); + + switch (serdes1_prtcl) { + case 0x60: + case 0x66: + case 0x67: + case 0x69: + lane_to_slot[1] = 7; + lane_to_slot[2] = 6; + lane_to_slot[3] = 5; + break; + case 0x86: + lane_to_slot[1] = 7; + lane_to_slot[2] = 7; + lane_to_slot[3] = 7; + break; + case 0x87: + lane_to_slot[1] = 7; + lane_to_slot[2] = 7; + lane_to_slot[3] = 7; + lane_to_slot[7] = 7; + break; + case 0x89: + lane_to_slot[1] = 7; + lane_to_slot[2] = 7; + lane_to_slot[3] = 7; + lane_to_slot[7] = 7; + break; + case 0x8d: + lane_to_slot[1] = 7; + lane_to_slot[2] = 7; + lane_to_slot[3] = 7; + lane_to_slot[5] = 3; + lane_to_slot[6] = 3; + lane_to_slot[7] = 3; + break; + case 0x8F: + case 0x85: + lane_to_slot[1] = 7; + lane_to_slot[2] = 6; + lane_to_slot[3] = 5; + lane_to_slot[6] = 3; + lane_to_slot[7] = 3; + break; + case 0xA5: + lane_to_slot[1] = 7; + lane_to_slot[6] = 3; + lane_to_slot[7] = 3; + break; + case 0xA7: + lane_to_slot[1] = 7; + lane_to_slot[7] = 7; + break; + case 0xAA: + lane_to_slot[1] = 7; + lane_to_slot[6] = 7; + lane_to_slot[7] = 7; + break; + case 0x40: + lane_to_slot[2] = 7; + lane_to_slot[3] = 7; + break; + default: + printf("qds: Fman: Unsupported SerDes Protocol 0x%02x\n", + serdes1_prtcl); + break; + } +} + +/* + * Given the following ... + * + * 1) A pointer to an Fman Ethernet node (as identified by the 'compat' + * compatible string and 'addr' physical address) + * + * 2) An Fman port + * + * ... update the phy-handle property of the Ethernet node to point to the + * right PHY. This assumes that we already know the PHY for each port. + * + * The offset of the Fman Ethernet node is also passed in for convenience, but + * it is not used, and we recalculate the offset anyway. + * + * Note that what we call "Fman ports" (enum fm_port) is really an Fman MAC. + * Inside the Fman, "ports" are things that connect to MACs. We only call them + * ports in U-Boot because on previous Ethernet devices (e.g. Gianfar), MACs + * and ports are the same thing. + * + */ +void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, + enum fm_port port, int offset) +{ + phy_interface_t intf = fm_info_get_enet_if(port); + char phy[16]; + + /* The RGMII PHY is identified by the MAC connected to it */ + if (intf == PHY_INTERFACE_MODE_RGMII) { + sprintf(phy, "rgmii_phy%u", port == FM1_DTSEC4 ? 1 : 2); + fdt_set_phy_handle(fdt, compat, addr, phy); + } + + /* The SGMII PHY is identified by the MAC connected to it */ + if (intf == PHY_INTERFACE_MODE_SGMII) { + int lane = serdes_get_first_lane(FSL_SRDS_1, SGMII_FM1_DTSEC1 + + port); + u8 slot; + if (lane < 0) + return; + slot = lane_to_slot[lane]; + if (slot) { + /* Slot housing a SGMII riser card */ + sprintf(phy, "phy_s%x_%02x", slot, + (fm_info_get_phy_address(port - FM1_DTSEC1)- + CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR + 1)); + fdt_set_phy_handle(fdt, compat, addr, phy); + } + } +} + +void fdt_fixup_board_enet(void *fdt) +{ + int i, lane, idx; + + for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { + idx = i - FM1_DTSEC1; + switch (fm_info_get_enet_if(i)) { + case PHY_INTERFACE_MODE_SGMII: + lane = serdes_get_first_lane(FSL_SRDS_1, + SGMII_FM1_DTSEC1 + idx); + if (lane < 0) + break; + + switch (mdio_mux[i]) { + case EMI1_SLOT3: + fdt_status_okay_by_alias(fdt, "emi1_slot3"); + break; + case EMI1_SLOT5: + fdt_status_okay_by_alias(fdt, "emi1_slot5"); + break; + case EMI1_SLOT6: + fdt_status_okay_by_alias(fdt, "emi1_slot6"); + break; + case EMI1_SLOT7: + fdt_status_okay_by_alias(fdt, "emi1_slot7"); + break; + } + break; + case PHY_INTERFACE_MODE_RGMII: + if (i == FM1_DTSEC4) + fdt_status_okay_by_alias(fdt, "emi1_rgmii0"); + + if (i == FM1_DTSEC5) + fdt_status_okay_by_alias(fdt, "emi1_rgmii1"); + break; + default: + break; + } + } +} +#endif /* #ifdef CONFIG_FMAN_ENET */ + +static void set_brdcfg9_for_gtx_clk(void) +{ + u8 brdcfg9; + brdcfg9 = QIXIS_READ(brdcfg[9]); + brdcfg9 |= (1 << 5); + QIXIS_WRITE(brdcfg[9], brdcfg9); +} + +void t1040_handle_phy_interface_sgmii(int i) +{ + int lane, idx, slot; + idx = i - FM1_DTSEC1; + lane = serdes_get_first_lane(FSL_SRDS_1, + SGMII_FM1_DTSEC1 + idx); + + if (lane < 0) + return; + slot = lane_to_slot[lane]; + + switch (slot) { + case 1: + mdio_mux[i] = EMI1_SLOT1; + fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); + break; + case 3: + if (FM1_DTSEC4 == i) + fm_info_set_phy_address(i, riser_phy_addr[0]); + if (FM1_DTSEC5 == i) + fm_info_set_phy_address(i, riser_phy_addr[1]); + + mdio_mux[i] = EMI1_SLOT3; + + fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); + break; + case 4: + mdio_mux[i] = EMI1_SLOT4; + fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); + break; + case 5: + /* Slot housing a SGMII riser card? */ + fm_info_set_phy_address(i, riser_phy_addr[0]); + mdio_mux[i] = EMI1_SLOT5; + fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); + break; + case 6: + /* Slot housing a SGMII riser card? */ + fm_info_set_phy_address(i, riser_phy_addr[0]); + mdio_mux[i] = EMI1_SLOT6; + fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); + break; + case 7: + if (FM1_DTSEC1 == i) + fm_info_set_phy_address(i, riser_phy_addr[0]); + if (FM1_DTSEC2 == i) + fm_info_set_phy_address(i, riser_phy_addr[1]); + if (FM1_DTSEC3 == i) + fm_info_set_phy_address(i, riser_phy_addr[2]); + + mdio_mux[i] = EMI1_SLOT7; + fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); + break; + default: + break; + } + fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); +} +void t1040_handle_phy_interface_rgmii(int i) +{ + fm_info_set_phy_address(i, i == FM1_DTSEC5 ? + CONFIG_SYS_FM1_DTSEC5_PHY_ADDR : + CONFIG_SYS_FM1_DTSEC4_PHY_ADDR); + mdio_mux[i] = (i == FM1_DTSEC5) ? EMI1_RGMII1 : + EMI1_RGMII0; + fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); +} + +int board_eth_init(bd_t *bis) +{ +#ifdef CONFIG_FMAN_ENET + struct memac_mdio_info memac_mdio_info; + unsigned int i; + + printf("Initializing Fman\n"); + set_brdcfg9_for_gtx_clk(); + + initialize_lane_to_slot(); + + /* Initialize the mdio_mux array so we can recognize empty elements */ + for (i = 0; i < NUM_FM_PORTS; i++) + mdio_mux[i] = EMI_NONE; + + memac_mdio_info.regs = + (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR; + memac_mdio_info.name = DEFAULT_FM_MDIO_NAME; + + /* Register the real 1G MDIO bus */ + fm_memac_mdio_init(bis, &memac_mdio_info); + + /* Register the muxing front-ends to the MDIO buses */ + t1040_qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII0); + t1040_qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII1); + t1040_qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT1); + t1040_qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT3); + t1040_qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT4); + t1040_qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT5); + t1040_qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT6); + t1040_qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT7); + + /* + * Program on board RGMII PHY addresses. If the SGMII Riser + * card used, we'll override the PHY address later. For any DTSEC that + * is RGMII, we'll also override its PHY address later. We assume that + * DTSEC4 and DTSEC5 are used for RGMII. + */ + fm_info_set_phy_address(FM1_DTSEC4, CONFIG_SYS_FM1_DTSEC4_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC5, CONFIG_SYS_FM1_DTSEC5_PHY_ADDR); + + for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { + switch (fm_info_get_enet_if(i)) { + case PHY_INTERFACE_MODE_QSGMII: + break; + case PHY_INTERFACE_MODE_SGMII: + t1040_handle_phy_interface_sgmii(i); + break; + + case PHY_INTERFACE_MODE_RGMII: + /* Only DTSEC4 and DTSEC5 can be routed to RGMII */ + t1040_handle_phy_interface_rgmii(i); + break; + default: + break; + } + } + + cpu_eth_init(bis); +#endif + + return pci_eth_init(bis); +} diff --git a/board/freescale/t1040qds/t1040qds.c b/board/freescale/t1040qds/t1040qds.c index de3ea5c..3dec447 100644 --- a/board/freescale/t1040qds/t1040qds.c +++ b/board/freescale/t1040qds/t1040qds.c @@ -223,6 +223,7 @@ void ft_board_setup(void *blob, bd_t *bd) #ifdef CONFIG_SYS_DPAA_FMAN fdt_fixup_fman_ethernet(blob); + fdt_fixup_board_enet(blob); #endif } diff --git a/board/freescale/t104xrdb/Makefile b/board/freescale/t104xrdb/Makefile index 76c0c94..e51fb7a 100644 --- a/board/freescale/t104xrdb/Makefile +++ b/board/freescale/t104xrdb/Makefile @@ -7,6 +7,7 @@ obj-y += t104xrdb.o obj-y += ddr.o +obj-y += eth.o obj-$(CONFIG_PCI) += pci.o obj-y += law.o obj-y += tlb.o diff --git a/board/freescale/t104xrdb/README b/board/freescale/t104xrdb/README index 11e03bd..1da52bb 100644 --- a/board/freescale/t104xrdb/README +++ b/board/freescale/t104xrdb/README @@ -164,14 +164,14 @@ NOR Flash memory Map 0xEFF40000 0xEFFFFFFF u-boot (current bank) 768KB 0xEFF20000 0xEFF3FFFF u-boot env (current bank) 128KB 0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB -0xED300000 0xEFF3FFFF rootfs (alt bank) 44MB + 256KB -0xEC800000 0xEC8FFFF Hardware device tree (alt bank) 1MB +0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB +0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB 0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB 0xEC000000 0xEC01FFFF RCW (alt bank) 128KB 0xEBF40000 0xEBFFFFFF u-boot (alt bank) 768KB 0xEBF20000 0xEBF3FFFF u-boot env (alt bank) 128KB 0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB -0xE9300000 0xEBF3FFFF rootfs (current bank) 44MB + 256KB +0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB 0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 11MB + 512KB 0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB 0xE8000000 0xE801FFFF RCW (current bank) 128KB diff --git a/board/freescale/t104xrdb/eth.c b/board/freescale/t104xrdb/eth.c new file mode 100644 index 0000000..0188fd4 --- /dev/null +++ b/board/freescale/t104xrdb/eth.c @@ -0,0 +1,72 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <netdev.h> +#include <asm/immap_85xx.h> +#include <fm_eth.h> +#include <fsl_mdio.h> +#include <malloc.h> +#include <asm/fsl_dtsec.h> + +#include "../common/fman.h" + +int board_eth_init(bd_t *bis) +{ +#ifdef CONFIG_FMAN_ENET + struct memac_mdio_info memac_mdio_info; + unsigned int i; + int phy_addr = 0; + printf("Initializing Fman\n"); + + memac_mdio_info.regs = + (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR; + memac_mdio_info.name = DEFAULT_FM_MDIO_NAME; + + /* Register the real 1G MDIO bus */ + fm_memac_mdio_init(bis, &memac_mdio_info); + + /* + * Program on board RGMII, SGMII PHY addresses. + */ + for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { + int idx = i - FM1_DTSEC1; + + switch (fm_info_get_enet_if(i)) { +#ifdef CONFIG_T1040RDB + case PHY_INTERFACE_MODE_SGMII: + /* T1040RDB only supports SGMII on DTSEC3 */ + fm_info_set_phy_address(FM1_DTSEC3, + CONFIG_SYS_SGMII1_PHY_ADDR); +#endif + case PHY_INTERFACE_MODE_RGMII: + if (FM1_DTSEC4 == i) + phy_addr = CONFIG_SYS_RGMII1_PHY_ADDR; + if (FM1_DTSEC5 == i) + phy_addr = CONFIG_SYS_RGMII2_PHY_ADDR; + fm_info_set_phy_address(i, phy_addr); + break; + case PHY_INTERFACE_MODE_QSGMII: + fm_info_set_phy_address(i, 0); + break; + case PHY_INTERFACE_MODE_NONE: + fm_info_set_phy_address(i, 0); + break; + default: + printf("Fman1: DTSEC%u set to unknown interface %i\n", + idx + 1, fm_info_get_enet_if(i)); + fm_info_set_phy_address(i, 0); + break; + } + fm_info_set_mdio(i, + miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME)); + } + + cpu_eth_init(bis); +#endif + + return pci_eth_init(bis); +} diff --git a/board/keymile/km_arm/fpga_config.c b/board/keymile/km_arm/fpga_config.c index cbfc7d2..51a3cfe 100644 --- a/board/keymile/km_arm/fpga_config.c +++ b/board/keymile/km_arm/fpga_config.c @@ -189,6 +189,31 @@ int wait_for_fpga_config(void) return 0; } +#if defined(KM_PCIE_RESET_MPP7) + +#define KM_PEX_RST_GPIO_PIN 7 +int fpga_reset(void) +{ + if (!check_boco2()) { + /* we do not have BOCO2, this is not really used */ + return 0; + } + + printf("PCIe reset through GPIO7: "); + /* apply PCIe reset via GPIO */ + kw_gpio_set_valid(KM_PEX_RST_GPIO_PIN, 1); + kw_gpio_direction_output(KM_PEX_RST_GPIO_PIN, 1); + kw_gpio_set_value(KM_PEX_RST_GPIO_PIN, 0); + udelay(1000*10); + kw_gpio_set_value(KM_PEX_RST_GPIO_PIN, 1); + + printf(" done\n"); + + return 0; +} + +#else + #define PRST1 0x4 #define PCIE_RST 0x10 #define TRAFFIC_RST 0x04 @@ -219,6 +244,7 @@ int fpga_reset(void) return 0; } +#endif /* the FPGA was configured, we configure the BOCO2 so that the EEPROM * is available from the Bobcat SPI bus */ diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c index 5620737..35402c8 100644 --- a/board/keymile/km_arm/km_arm.c +++ b/board/keymile/km_arm/km_arm.c @@ -46,7 +46,11 @@ static const u32 kwmpp_config[] = { MPP4_NF_IO6, MPP5_NF_IO7, MPP6_SYSRST_OUTn, +#if defined(KM_PCIE_RESET_MPP7) + MPP7_GPO, +#else MPP7_PEX_RST_OUTn, +#endif #if defined(CONFIG_SYS_I2C_SOFT) MPP8_GPIO, /* SDA */ MPP9_GPIO, /* SCL */ @@ -102,7 +106,7 @@ static const u32 kwmpp_config[] = { /* * Wait for startup OK from mgcoge3ne */ -int startup_allowed(void) +static int startup_allowed(void) { unsigned char buf; @@ -164,7 +168,6 @@ static int initialize_unit_leds(void) return 0; } -#if defined(CONFIG_BOOTCOUNT_LIMIT) static void set_bootcount_addr(void) { uchar buf[32]; @@ -173,7 +176,6 @@ static void set_bootcount_addr(void) sprintf((char *)buf, "0x%x", bootcountaddr); setenv("bootcountaddr", (char *)buf); } -#endif int misc_init_r(void) { @@ -210,9 +212,7 @@ int misc_init_r(void) initialize_unit_leds(); set_km_env(); -#if defined(CONFIG_BOOTCOUNT_LIMIT) set_bootcount_addr(); -#endif return 0; } @@ -322,15 +322,15 @@ void reset_phy(void) return; /* RGMII clk transition on data stable */ - if (!miiphy_read(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG, ®)) + if (miiphy_read(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG, ®)) printf("Error reading PHY spec ctrl reg\n"); - if (!miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG, - reg | PHY_RGMII_CLK_STABLE | PHY_CLSA)) + if (miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG, + reg | PHY_RGMII_CLK_STABLE | PHY_CLSA)) printf("Error writing PHY spec ctrl reg\n"); /* leds setup */ - if (!miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_LED_SEL_REG, - PHY_LED0_LINK | PHY_LED1_ACT | PHY_LED2_INT)) + if (miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_LED_SEL_REG, + PHY_LED0_LINK | PHY_LED1_ACT | PHY_LED2_INT)) printf("Error writing PHY LED reg\n"); /* reset the phy */ diff --git a/board/keymile/kmp204x/Makefile b/board/keymile/kmp204x/Makefile index 3e69ee2..c57ca08 100644 --- a/board/keymile/kmp204x/Makefile +++ b/board/keymile/kmp204x/Makefile @@ -8,5 +8,5 @@ # SPDX-License-Identifier: GPL-2.0+ # -obj-y := kmp204x.o ddr.o eth.o tlb.o pci.o law.o \ +obj-y := kmp204x.o ddr.o eth.o tlb.o pci.o law.o qrio.o \ ../common/common.o ../common/ivm.o diff --git a/board/keymile/kmp204x/kmp204x.c b/board/keymile/kmp204x/kmp204x.c index f02642a..95a19cd 100644 --- a/board/keymile/kmp204x/kmp204x.c +++ b/board/keymile/kmp204x/kmp204x.c @@ -33,12 +33,51 @@ int checkboard(void) return 0; } -/* TODO: implement the I2C deblocking function */ -int i2c_make_abort(void) +/* I2C deblocking uses the algorithm defined in board/keymile/common/common.c + * 2 dedicated QRIO GPIOs externally pull the SCL and SDA lines + * For I2C only the low state is activly driven and high state is pulled-up + * by a resistor. Therefore the deblock GPIOs are used + * -> as an active output to drive a low state + * -> as an open-drain input to have a pulled-up high state + */ + +/* QRIO GPIOs used for deblocking */ +#define DEBLOCK_PORT1 GPIO_A +#define DEBLOCK_SCL1 20 +#define DEBLOCK_SDA1 21 + +/* By default deblock GPIOs are floating */ +static void i2c_deblock_gpio_cfg(void) +{ + /* set I2C bus 1 deblocking GPIOs input, but 0 value for open drain */ + qrio_gpio_direction_input(DEBLOCK_PORT1, DEBLOCK_SCL1); + qrio_gpio_direction_input(DEBLOCK_PORT1, DEBLOCK_SDA1); + + qrio_set_gpio(DEBLOCK_PORT1, DEBLOCK_SCL1, 0); + qrio_set_gpio(DEBLOCK_PORT1, DEBLOCK_SDA1, 0); +} + +void set_sda(int state) +{ + qrio_set_opendrain_gpio(DEBLOCK_PORT1, DEBLOCK_SDA1, state); +} + +void set_scl(int state) +{ + qrio_set_opendrain_gpio(DEBLOCK_PORT1, DEBLOCK_SCL1, state); +} + +int get_sda(void) +{ + return qrio_get_gpio(DEBLOCK_PORT1, DEBLOCK_SDA1); +} + +int get_scl(void) { - return 1; + return qrio_get_gpio(DEBLOCK_PORT1, DEBLOCK_SCL1); } + #define ZL30158_RST 8 #define ZL30343_RST 9 @@ -62,6 +101,7 @@ int board_early_init_f(void) int board_early_init_r(void) { + int ret = 0; /* Flush d-cache and invalidate i-cache of any FLASH data */ flush_dcache(); invalidate_icache(); @@ -69,7 +109,11 @@ int board_early_init_r(void) set_liodns(); setup_portals(); - return 0; + ret = trigger_fpga_config(); + if (ret) + printf("error triggering PCIe FPGA config\n"); + + return ret; } unsigned long get_board_sys_clk(unsigned long dummy) @@ -77,80 +121,12 @@ unsigned long get_board_sys_clk(unsigned long dummy) return 66666666; } -#define WDMASK_OFF 0x16 - -static void qrio_wdmask(u8 bit, bool wden) -{ - u16 wdmask; - void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; - - wdmask = in_be16(qrio_base + WDMASK_OFF); - - if (wden) - wdmask |= (1 << bit); - else - wdmask &= ~(1 << bit); - - out_be16(qrio_base + WDMASK_OFF, wdmask); -} - -#define PRST_OFF 0x1a - -void qrio_prst(u8 bit, bool en, bool wden) -{ - u16 prst; - void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; - - qrio_wdmask(bit, wden); - - prst = in_be16(qrio_base + PRST_OFF); - - if (en) - prst &= ~(1 << bit); - else - prst |= (1 << bit); - - out_be16(qrio_base + PRST_OFF, prst); -} - -#define PRSTCFG_OFF 0x1c - -void qrio_prstcfg(u8 bit, u8 mode) -{ - u32 prstcfg; - u8 i; - void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; - - prstcfg = in_be32(qrio_base + PRSTCFG_OFF); - - for (i = 0; i < 2; i++) { - if (mode & (1<<i)) - set_bit(2*bit+i, &prstcfg); - else - clear_bit(2*bit+i, &prstcfg); - } - - out_be32(qrio_base + PRSTCFG_OFF, prstcfg); -} - - -#define BOOTCOUNT_OFF 0x12 - -void bootcount_store(ulong counter) +int misc_init_f(void) { - u8 val; - void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; - - val = (counter <= 255) ? (u8)counter : 255; - out_8(qrio_base + BOOTCOUNT_OFF, val); -} + /* configure QRIO pis for i2c deblocking */ + i2c_deblock_gpio_cfg(); -ulong bootcount_load(void) -{ - u8 val; - void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; - val = in_8(qrio_base + BOOTCOUNT_OFF); - return val; + return 0; } #define NUM_SRDS_BANKS 2 diff --git a/board/keymile/kmp204x/kmp204x.h b/board/keymile/kmp204x/kmp204x.h index b6ba672..0267596 100644 --- a/board/keymile/kmp204x/kmp204x.h +++ b/board/keymile/kmp204x/kmp204x.h @@ -5,6 +5,16 @@ * SPDX-License-Identifier: GPL-2.0+ */ +/* QRIO GPIO ports */ +#define GPIO_A 0x40 +#define GPIO_B 0x60 + +int qrio_get_gpio(u8 port_off, u8 gpio_nr); +void qrio_set_opendrain_gpio(u8 port_off, u8 gpio_nr, u8 val); +void qrio_set_gpio(u8 port_off, u8 gpio_nr, bool value); +void qrio_gpio_direction_output(u8 port_off, u8 gpio_nr, bool value); +void qrio_gpio_direction_input(u8 port_off, u8 gpio_nr); + #define PRSTCFG_POWUP_UNIT_CORE_RST 0x0 #define PRSTCFG_POWUP_UNIT_RST 0x1 #define PRSTCFG_POWUP_RST 0x3 diff --git a/board/keymile/kmp204x/pbi.cfg b/board/keymile/kmp204x/pbi.cfg index f38dcf9..9af8bd5 100644 --- a/board/keymile/kmp204x/pbi.cfg +++ b/board/keymile/kmp204x/pbi.cfg @@ -8,6 +8,16 @@ # #PBI commands +#Workaround for A-006559 needed for rev 2.0 of P2041 silicon +#Freescale's errarta sheet suggests it may be done with PBI +09000010 00000000 +09000014 00000000 +09000018 81d00000 +09021008 0000f000 +09021028 0000f000 +09021048 0000f000 +09021068 0000f000 +09000018 00000000 #Initialize CPC1 as 1MB SRAM 09010000 00200400 09138000 00000000 diff --git a/board/keymile/kmp204x/pci.c b/board/keymile/kmp204x/pci.c index ec20c8a..a484eb5 100644 --- a/board/keymile/kmp204x/pci.c +++ b/board/keymile/kmp204x/pci.c @@ -14,18 +14,103 @@ #include <libfdt.h> #include <fdt_support.h> #include <asm/fsl_serdes.h> +#include <asm/errno.h> #include "kmp204x.h" +#define PROM_SEL_L 11 +/* control the PROM_SEL_L signal*/ +static void toggle_fpga_eeprom_bus(bool cpu_own) +{ + qrio_gpio_direction_output(GPIO_A, PROM_SEL_L, !cpu_own); +} + +#define CONF_SEL_L 10 +#define FPGA_PROG_L 19 +#define FPGA_DONE 18 +#define FPGA_INIT_L 17 + +int trigger_fpga_config(void) +{ + int ret = 0, init_l; + /* approx 10ms */ + u32 timeout = 10000; + + /* make sure the FPGA_can access the EEPROM */ + toggle_fpga_eeprom_bus(false); + + /* assert CONF_SEL_L to be able to drive FPGA_PROG_L */ + qrio_gpio_direction_output(GPIO_A, CONF_SEL_L, 0); + + /* trigger the config start */ + qrio_gpio_direction_output(GPIO_A, FPGA_PROG_L, 0); + + /* small delay for INIT_L line */ + udelay(10); + + /* wait for FPGA_INIT to be asserted */ + do { + init_l = qrio_get_gpio(GPIO_A, FPGA_INIT_L); + if (timeout-- == 0) { + printf("FPGA_INIT timeout\n"); + ret = -EFAULT; + break; + } + udelay(10); + } while (init_l); + + /* deassert FPGA_PROG, config should start */ + qrio_set_gpio(GPIO_A, FPGA_PROG_L, 1); + + return ret; +} + +/* poll the FPGA_DONE signal and give the EEPROM back to the QorIQ */ +static int wait_for_fpga_config(void) +{ + int ret = 0, done; + /* approx 5 s */ + u32 timeout = 500000; + + printf("PCIe FPGA config:"); + do { + done = qrio_get_gpio(GPIO_A, FPGA_DONE); + if (timeout-- == 0) { + printf(" FPGA_DONE timeout\n"); + ret = -EFAULT; + goto err_out; + } + udelay(10); + } while (!done); + + printf(" done\n"); + +err_out: + /* deactive CONF_SEL and give the CPU conf EEPROM access */ + qrio_set_gpio(GPIO_A, CONF_SEL_L, 1); + toggle_fpga_eeprom_bus(true); + + return ret; +} + #define PCIE_SW_RST 14 +#define PEXHC_SW_RST 13 #define HOOPER_SW_RST 12 void pci_init_board(void) { + /* first wait for the PCIe FPGA to be configured + * it has been triggered earlier in board_early_init_r */ + int ret = wait_for_fpga_config(); + if (ret) + printf("error finishing PCIe FPGA config\n"); + qrio_prst(PCIE_SW_RST, false, false); + qrio_prst(PEXHC_SW_RST, false, false); qrio_prst(HOOPER_SW_RST, false, false); /* Hooper is not direcly PCIe capable */ mdelay(50); + fsl_pcie_init_board(0); } diff --git a/board/keymile/kmp204x/qrio.c b/board/keymile/kmp204x/qrio.c new file mode 100644 index 0000000..49f9aa2 --- /dev/null +++ b/board/keymile/kmp204x/qrio.c @@ -0,0 +1,146 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp <valentin.longchamp@keymile.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> + +#include "../common/common.h" +#include "kmp204x.h" + +/* QRIO GPIO register offsets */ +#define DIRECT_OFF 0x18 +#define GPRT_OFF 0x1c + +int qrio_get_gpio(u8 port_off, u8 gpio_nr) +{ + u32 gprt; + + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + gprt = in_be32(qrio_base + port_off + GPRT_OFF); + + return (gprt >> gpio_nr) & 1U; +} + +void qrio_set_gpio(u8 port_off, u8 gpio_nr, bool value) +{ + u32 gprt, mask; + + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + mask = 1U << gpio_nr; + + gprt = in_be32(qrio_base + port_off + GPRT_OFF); + if (value) + gprt |= mask; + else + gprt &= ~mask; + + out_be32(qrio_base + port_off + GPRT_OFF, gprt); +} + +void qrio_gpio_direction_output(u8 port_off, u8 gpio_nr, bool value) +{ + u32 direct, mask; + + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + mask = 1U << gpio_nr; + + direct = in_be32(qrio_base + port_off + DIRECT_OFF); + direct |= mask; + out_be32(qrio_base + port_off + DIRECT_OFF, direct); + + qrio_set_gpio(port_off, gpio_nr, value); +} + +void qrio_gpio_direction_input(u8 port_off, u8 gpio_nr) +{ + u32 direct, mask; + + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + mask = 1U << gpio_nr; + + direct = in_be32(qrio_base + port_off + DIRECT_OFF); + direct &= ~mask; + out_be32(qrio_base + port_off + DIRECT_OFF, direct); +} + +void qrio_set_opendrain_gpio(u8 port_off, u8 gpio_nr, u8 val) +{ + u32 direct, mask; + + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + mask = 1U << gpio_nr; + + direct = in_be32(qrio_base + port_off + DIRECT_OFF); + if (val == 0) + /* set to output -> GPIO drives low */ + direct |= mask; + else + /* set to input -> GPIO floating */ + direct &= ~mask; + + out_be32(qrio_base + port_off + DIRECT_OFF, direct); +} + +#define WDMASK_OFF 0x16 + +static void qrio_wdmask(u8 bit, bool wden) +{ + u16 wdmask; + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + wdmask = in_be16(qrio_base + WDMASK_OFF); + + if (wden) + wdmask |= (1 << bit); + else + wdmask &= ~(1 << bit); + + out_be16(qrio_base + WDMASK_OFF, wdmask); +} + +#define PRST_OFF 0x1a + +void qrio_prst(u8 bit, bool en, bool wden) +{ + u16 prst; + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + qrio_wdmask(bit, wden); + + prst = in_be16(qrio_base + PRST_OFF); + + if (en) + prst &= ~(1 << bit); + else + prst |= (1 << bit); + + out_be16(qrio_base + PRST_OFF, prst); +} + +#define PRSTCFG_OFF 0x1c + +void qrio_prstcfg(u8 bit, u8 mode) +{ + u32 prstcfg; + u8 i; + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + prstcfg = in_be32(qrio_base + PRSTCFG_OFF); + + for (i = 0; i < 2; i++) { + if (mode & (1<<i)) + set_bit(2*bit+i, &prstcfg); + else + clear_bit(2*bit+i, &prstcfg); + } + + out_be32(qrio_base + PRSTCFG_OFF, prstcfg); +} diff --git a/board/keymile/kmp204x/rcw_kmp204x.cfg b/board/keymile/kmp204x/rcw_kmp204x.cfg index f2b7fe3..2d4c48c 100644 --- a/board/keymile/kmp204x/rcw_kmp204x.cfg +++ b/board/keymile/kmp204x/rcw_kmp204x.cfg @@ -7,5 +7,5 @@ aa55aa55 010e0100 #64 bytes RCW data 14600000 00000000 28200000 00000000 148E70CF CFC02000 58000000 41000000 -00000000 00000000 00000000 F4428002 +00000000 00000000 00000000 F0428002 00000000 00000000 00000000 00000000 diff --git a/board/keymile/scripts/develop-arm.txt b/board/keymile/scripts/develop-arm.txt index 922afea..d3c974f 100644 --- a/board/keymile/scripts/develop-arm.txt +++ b/board/keymile/scripts/develop-arm.txt @@ -1,2 +1 @@ setup_debug_env=tftpboot 0x200000 scripts/develop-common.txt && env import -t 0x200000 ${filesize} && run configure -tftpfdt=true diff --git a/board/keymile/scripts/develop-common.txt b/board/keymile/scripts/develop-common.txt index a6bb1b1..a80812a 100644 --- a/board/keymile/scripts/develop-common.txt +++ b/board/keymile/scripts/develop-common.txt @@ -3,6 +3,7 @@ bootcmd=run ${subbootcmds} configure=run set_uimage; km_setboardid && saveenv && reset subbootcmds=tftpfdt tftpkernel nfsargs add_default boot nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${toolchain}/${arch} +tftpfdt=if run set_fdthigh || test ${arch} != arm; then tftpboot ${fdt_addr_r} ${hostname}/${hostname}.dtb; else true; fi tftpkernel=tftpboot ${load_addr_r} ${hostname}/${uimage} toolchain=/opt/eldk rootfssize=0 diff --git a/board/keymile/scripts/develop-ppc_82xx.txt b/board/keymile/scripts/develop-ppc_82xx.txt index 909f6a3..d3c974f 100644 --- a/board/keymile/scripts/develop-ppc_82xx.txt +++ b/board/keymile/scripts/develop-ppc_82xx.txt @@ -1,2 +1 @@ setup_debug_env=tftpboot 0x200000 scripts/develop-common.txt && env import -t 0x200000 ${filesize} && run configure -tftpfdt=tftpboot ${fdt_addr_r} ${hostname}/${hostname}.dtb diff --git a/board/keymile/scripts/develop-ppc_8xx.txt b/board/keymile/scripts/develop-ppc_8xx.txt index 909f6a3..d3c974f 100644 --- a/board/keymile/scripts/develop-ppc_8xx.txt +++ b/board/keymile/scripts/develop-ppc_8xx.txt @@ -1,2 +1 @@ setup_debug_env=tftpboot 0x200000 scripts/develop-common.txt && env import -t 0x200000 ${filesize} && run configure -tftpfdt=tftpboot ${fdt_addr_r} ${hostname}/${hostname}.dtb diff --git a/board/keymile/scripts/ramfs-arm.txt b/board/keymile/scripts/ramfs-arm.txt index 79974f1..87e984e 100644 --- a/board/keymile/scripts/ramfs-arm.txt +++ b/board/keymile/scripts/ramfs-arm.txt @@ -1,2 +1 @@ setup_debug_env=tftpboot 0x200000 scripts/ramfs-common.txt && env import -t 0x200000 ${filesize} && run configure -tftpfdt=true diff --git a/board/keymile/scripts/ramfs-common.txt b/board/keymile/scripts/ramfs-common.txt index 502c863..d79ad2e 100644 --- a/board/keymile/scripts/ramfs-common.txt +++ b/board/keymile/scripts/ramfs-common.txt @@ -7,6 +7,7 @@ nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} configure=run set_uimage; km_setboardid && saveenv && reset rootfsfile=${hostname}/rootfsImage setrootfsaddr=setexpr value ${pnvramaddr} - ${rootfssize} && setenv rootfsaddr 0x${value} +tftpfdt=if run set_fdthigh || test ${arch} != arm; then tftpboot ${fdt_addr_r} ${hostname}/${hostname}.dtb; else true; fi tftpkernel=tftpboot ${load_addr_r} ${hostname}/${uimage} tftpramfs=tftpboot ${rootfsaddr} ${hostname}/rootfsImage set_uimage=printenv uimage || setenv uimage uImage diff --git a/board/keymile/scripts/ramfs-ppc_82xx.txt b/board/keymile/scripts/ramfs-ppc_82xx.txt index 970927a..87e984e 100644 --- a/board/keymile/scripts/ramfs-ppc_82xx.txt +++ b/board/keymile/scripts/ramfs-ppc_82xx.txt @@ -1,2 +1 @@ setup_debug_env=tftpboot 0x200000 scripts/ramfs-common.txt && env import -t 0x200000 ${filesize} && run configure -tftpfdt=tftpboot ${fdt_addr_r} ${hostname}/${hostname}.dtb diff --git a/board/keymile/scripts/ramfs-ppc_8xx.txt b/board/keymile/scripts/ramfs-ppc_8xx.txt index 970927a..87e984e 100644 --- a/board/keymile/scripts/ramfs-ppc_8xx.txt +++ b/board/keymile/scripts/ramfs-ppc_8xx.txt @@ -1,2 +1 @@ setup_debug_env=tftpboot 0x200000 scripts/ramfs-common.txt && env import -t 0x200000 ${filesize} && run configure -tftpfdt=tftpboot ${fdt_addr_r} ${hostname}/${hostname}.dtb diff --git a/board/nvidia/common/board.c b/board/nvidia/common/board.c index e650fed..3b18e28 100644 --- a/board/nvidia/common/board.c +++ b/board/nvidia/common/board.c @@ -67,12 +67,14 @@ void __gpio_early_init_uart(void) void gpio_early_init_uart(void) __attribute__((weak, alias("__gpio_early_init_uart"))); +#if defined(CONFIG_TEGRA_NAND) void __pin_mux_nand(void) { funcmux_select(PERIPH_ID_NDFLASH, FUNCMUX_DEFAULT); } void pin_mux_nand(void) __attribute__((weak, alias("__pin_mux_nand"))); +#endif void __pin_mux_display(void) { diff --git a/board/nvidia/dts/tegra124-venice2.dts b/board/nvidia/dts/tegra124-venice2.dts new file mode 100644 index 0000000..2f8d1dc --- /dev/null +++ b/board/nvidia/dts/tegra124-venice2.dts @@ -0,0 +1,84 @@ +/dts-v1/; + +#include "tegra124.dtsi" + +/ { + model = "NVIDIA Venice2"; + compatible = "nvidia,venice2", "nvidia,tegra124"; + + aliases { + i2c0 = "/i2c@7000d000"; + i2c1 = "/i2c@7000c000"; + i2c2 = "/i2c@7000c400"; + i2c3 = "/i2c@7000c500"; + i2c4 = "/i2c@7000c700"; + i2c5 = "/i2c@7000d100"; + sdhci0 = "/sdhci@700b0600"; + sdhci1 = "/sdhci@700b0400"; + spi0 = "/spi@7000d400"; + spi1 = "/spi@7000da00"; + usb0 = "/usb@7d008000"; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x80000000>; + }; + + i2c@7000c000 { + status = "okay"; + clock-frequency = <100000>; + }; + + i2c@7000c400 { + status = "okay"; + clock-frequency = <100000>; + }; + + i2c@7000c500 { + status = "okay"; + clock-frequency = <100000>; + }; + + i2c@7000c700 { + status = "okay"; + clock-frequency = <100000>; + }; + + i2c@7000d000 { + status = "okay"; + clock-frequency = <400000>; + }; + + i2c@7000d100 { + status = "okay"; + clock-frequency = <400000>; + }; + + spi@7000d400 { + status = "okay"; + spi-max-frequency = <25000000>; + }; + + spi@7000da00 { + status = "okay"; + spi-max-frequency = <25000000>; + }; + + sdhci@700b0400 { + status = "okay"; + cd-gpios = <&gpio 170 0>; /* gpio PV2 */ + power-gpios = <&gpio 136 0>; /* gpio PR0 */ + bus-width = <4>; + }; + + sdhci@700b0600 { + status = "okay"; + bus-width = <8>; + }; + + usb@7d008000 { + status = "okay"; + nvidia,vbus-gpio = <&gpio 109 0>; /* gpio PN5, USB_VBUS_EN1 */ + }; +}; diff --git a/board/nvidia/venice2/Makefile b/board/nvidia/venice2/Makefile new file mode 100644 index 0000000..5fac5ab --- /dev/null +++ b/board/nvidia/venice2/Makefile @@ -0,0 +1,9 @@ +# +# (C) Copyright 2013-2014 +# NVIDIA Corporation <www.nvidia.com> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += as3722_init.o +obj-y += venice2.o diff --git a/board/nvidia/venice2/as3722_init.c b/board/nvidia/venice2/as3722_init.c new file mode 100644 index 0000000..960fea7 --- /dev/null +++ b/board/nvidia/venice2/as3722_init.c @@ -0,0 +1,91 @@ +/* + * (C) Copyright 2013 + * NVIDIA Corporation <www.nvidia.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/arch-tegra/tegra_i2c.h> +#include "as3722_init.h" + +/* AS3722-PMIC-specific early init code - get CPU rails up, etc */ + +void tegra_i2c_ll_write_addr(uint addr, uint config) +{ + struct i2c_ctlr *reg = (struct i2c_ctlr *)TEGRA_DVC_BASE; + + writel(addr, ®->cmd_addr0); + writel(config, ®->cnfg); +} + +void tegra_i2c_ll_write_data(uint data, uint config) +{ + struct i2c_ctlr *reg = (struct i2c_ctlr *)TEGRA_DVC_BASE; + + writel(data, ®->cmd_data1); + writel(config, ®->cnfg); +} + +void pmic_enable_cpu_vdd(void) +{ + debug("%s entry\n", __func__); + + /* Don't need to set up VDD_CORE - already done - by OTP */ + + debug("%s: Setting VDD_CPU to 1.0V via AS3722 reg 0/4D\n", __func__); + /* + * Bring up VDD_CPU via the AS3722 PMIC on the PWR I2C bus. + * First set VDD to 1.0V, then enable the VDD regulator. + */ + tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2); + tegra_i2c_ll_write_data(AS3722_SD0VOLTAGE_DATA, I2C_SEND_2_BYTES); + /* + * Don't write SDCONTROL - it's already 0x7F, i.e. all SDs enabled. + * tegra_i2c_ll_write_data(AS3722_SD0CONTROL_DATA, I2C_SEND_2_BYTES); + */ + udelay(10 * 1000); + + debug("%s: Setting VDD_GPU to 1.0V via AS3722 reg 6/4D\n", __func__); + /* + * Bring up VDD_GPU via the AS3722 PMIC on the PWR I2C bus. + * First set VDD to 1.0V, then enable the VDD regulator. + */ + tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2); + tegra_i2c_ll_write_data(AS3722_SD6VOLTAGE_DATA, I2C_SEND_2_BYTES); + /* + * Don't write SDCONTROL - it's already 0x7F, i.e. all SDs enabled. + * tegra_i2c_ll_write_data(AS3722_SD6CONTROL_DATA, I2C_SEND_2_BYTES); + */ + udelay(10 * 1000); + + debug("%s: Set VPP_FUSE to 1.2V via AS3722 reg 0x12/4E\n", __func__); + /* + * Bring up VPP_FUSE via the AS3722 PMIC on the PWR I2C bus. + * First set VDD to 1.2V, then enable the VDD regulator. + */ + tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2); + tegra_i2c_ll_write_data(AS3722_LDO2VOLTAGE_DATA, I2C_SEND_2_BYTES); + /* + * Don't write LDCONTROL - it's already 0xFF, i.e. all LDOs enabled. + * tegra_i2c_ll_write_data(AS3722_LDO2CONTROL_DATA, I2C_SEND_2_BYTES); + */ + udelay(10 * 1000); + + debug("%s: Set VDD_SDMMC to 3.3V via AS3722 reg 0x16/4E\n", __func__); + /* + * Bring up VDD_SDMMC via the AS3722 PMIC on the PWR I2C bus. + * First set it to bypass 3.3V straight thru, then enable the regulator + * + * NOTE: We do this early because doing it later seems to hose the CPU + * power rail/partition startup. Need to debug. + */ + tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2); + tegra_i2c_ll_write_data(AS3722_LDO6VOLTAGE_DATA, I2C_SEND_2_BYTES); + /* + * Don't write LDCONTROL - it's already 0xFF, i.e. all LDOs enabled. + * tegra_i2c_ll_write_data(AS3722_LDO6CONTROL_DATA, I2C_SEND_2_BYTES); + */ + udelay(10 * 1000); +} diff --git a/board/nvidia/venice2/as3722_init.h b/board/nvidia/venice2/as3722_init.h new file mode 100644 index 0000000..2a9e7cd --- /dev/null +++ b/board/nvidia/venice2/as3722_init.h @@ -0,0 +1,38 @@ +/* + * (C) Copyright 2013 + * NVIDIA Corporation <www.nvidia.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* AS3722-PMIC-specific early init regs */ + +#define AS3722_I2C_ADDR 0x80 + +#define AS3722_SD0VOLTAGE_REG 0x00 /* CPU */ +#define AS3722_SD1VOLTAGE_REG 0x01 /* CORE, already set by OTP */ +#define AS3722_SD6VOLTAGE_REG 0x06 /* GPU */ +#define AS3722_SDCONTROL_REG 0x4D + +#define AS3722_LDO2VOLTAGE_REG 0x12 /* VPP_FUSE */ +#define AS3722_LDO6VOLTAGE_REG 0x16 /* VDD_SDMMC */ +#define AS3722_LDCONTROL_REG 0x4E + +#define AS3722_SD0VOLTAGE_DATA (0x2800 | AS3722_SD0VOLTAGE_REG) +#define AS3722_SD0CONTROL_DATA (0x0100 | AS3722_SDCONTROL_REG) + +#define AS3722_SD1VOLTAGE_DATA (0x3200 | AS3722_SD1VOLTAGE_REG) +#define AS3722_SD1CONTROL_DATA (0x0200 | AS3722_SDCONTROL_REG) + +#define AS3722_SD6CONTROL_DATA (0x4000 | AS3722_SDCONTROL_REG) +#define AS3722_SD6VOLTAGE_DATA (0x2800 | AS3722_SD6VOLTAGE_REG) + +#define AS3722_LDO2CONTROL_DATA (0x0400 | AS3722_LDCONTROL_REG) +#define AS3722_LDO2VOLTAGE_DATA (0x1000 | AS3722_LDO2VOLTAGE_REG) + +#define AS3722_LDO6CONTROL_DATA (0x4000 | AS3722_LDCONTROL_REG) +#define AS3722_LDO6VOLTAGE_DATA (0x3F00 | AS3722_LDO6VOLTAGE_REG) + +#define I2C_SEND_2_BYTES 0x0A02 + +void pmic_enable_cpu_vdd(void); diff --git a/board/nvidia/venice2/pinmux-config-venice2.h b/board/nvidia/venice2/pinmux-config-venice2.h new file mode 100644 index 0000000..50868e6 --- /dev/null +++ b/board/nvidia/venice2/pinmux-config-venice2.h @@ -0,0 +1,339 @@ +/* + * (C) Copyright 2013 + * NVIDIA Corporation <www.nvidia.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _PINMUX_CONFIG_VENICE2_H_ +#define _PINMUX_CONFIG_VENICE2_H_ + +#define DEFAULT_PINMUX(_pingroup, _mux, _pull, _tri, _io) \ + { \ + .pingroup = PINGRP_##_pingroup, \ + .func = PMUX_FUNC_##_mux, \ + .pull = PMUX_PULL_##_pull, \ + .tristate = PMUX_TRI_##_tri, \ + .io = PMUX_PIN_##_io, \ + .lock = PMUX_PIN_LOCK_DEFAULT, \ + .od = PMUX_PIN_OD_DEFAULT, \ + .ioreset = PMUX_PIN_IO_RESET_DEFAULT, \ + } + +#define I2C_PINMUX(_pingroup, _mux, _pull, _tri, _io, _lock, _od) \ + { \ + .pingroup = PINGRP_##_pingroup, \ + .func = PMUX_FUNC_##_mux, \ + .pull = PMUX_PULL_##_pull, \ + .tristate = PMUX_TRI_##_tri, \ + .io = PMUX_PIN_##_io, \ + .lock = PMUX_PIN_LOCK_##_lock, \ + .od = PMUX_PIN_OD_##_od, \ + .ioreset = PMUX_PIN_IO_RESET_DEFAULT, \ + } + +#define DDC_PINMUX(_pingroup, _mux, _pull, _tri, _io, _lock, _rcv_sel) \ + { \ + .pingroup = PINGRP_##_pingroup, \ + .func = PMUX_FUNC_##_mux, \ + .pull = PMUX_PULL_##_pull, \ + .tristate = PMUX_TRI_##_tri, \ + .io = PMUX_PIN_##_io, \ + .lock = PMUX_PIN_LOCK_##_lock, \ + .rcv_sel = PMUX_PIN_RCV_SEL_##_rcv_sel, \ + .ioreset = PMUX_PIN_IO_RESET_DEFAULT, \ + } + +#define VI_PINMUX(_pingroup, _mux, _pull, _tri, _io, _lock, _ioreset) \ + { \ + .pingroup = PINGRP_##_pingroup, \ + .func = PMUX_FUNC_##_mux, \ + .pull = PMUX_PULL_##_pull, \ + .tristate = PMUX_TRI_##_tri, \ + .io = PMUX_PIN_##_io, \ + .lock = PMUX_PIN_LOCK_##_lock, \ + .od = PMUX_PIN_OD_DEFAULT, \ + .ioreset = PMUX_PIN_IO_RESET_##_ioreset \ + } + +#define CEC_PINMUX(_pingroup, _mux, _pull, _tri, _io, _lock, _od) \ + { \ + .pingroup = PINGRP_##_pingroup, \ + .func = PMUX_FUNC_##_mux, \ + .pull = PMUX_PULL_##_pull, \ + .tristate = PMUX_TRI_##_tri, \ + .io = PMUX_PIN_##_io, \ + .lock = PMUX_PIN_LOCK_##_lock, \ + .od = PMUX_PIN_OD_##_od, \ + .ioreset = PMUX_PIN_IO_RESET_DEFAULT, \ + } + +#define USB_PINMUX CEC_PINMUX + +#define DEFAULT_PADCFG(_padgrp, _slwf, _slwr, _drvup, _drvdn, _lpmd, _schmt, _hsm) \ + { \ + .padgrp = PDRIVE_PINGROUP_##_padgrp, \ + .slwf = _slwf, \ + .slwr = _slwr, \ + .drvup = _drvup, \ + .drvdn = _drvdn, \ + .lpmd = PGRP_LPMD_##_lpmd, \ + .schmt = PGRP_SCHMT_##_schmt, \ + .hsm = PGRP_HSM_##_hsm, \ + } + +static struct pingroup_config tegra124_pinmux_common[] = { + /* EXTPERIPH1 pinmux */ + DEFAULT_PINMUX(CLK1_OUT, EXTPERIPH1, NORMAL, NORMAL, OUTPUT), + + /* I2S0 pinmux */ + DEFAULT_PINMUX(DAP1_DIN, I2S0, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(DAP1_DOUT, I2S0, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(DAP1_FS, I2S0, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(DAP1_SCLK, I2S0, NORMAL, NORMAL, INPUT), + + /* I2S1 pinmux */ + DEFAULT_PINMUX(DAP2_DIN, I2S1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(DAP2_DOUT, I2S1, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(DAP2_FS, I2S1, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(DAP2_SCLK, I2S1, NORMAL, NORMAL, INPUT), + + /* I2S3 pinmux */ + DEFAULT_PINMUX(DAP4_DIN, I2S3, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(DAP4_DOUT, I2S3, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(DAP4_FS, I2S3, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(DAP4_SCLK, I2S3, NORMAL, NORMAL, INPUT), + + /* CLDVFS pinmux */ + DEFAULT_PINMUX(DVFS_PWM, CLDVFS, NORMAL, NORMAL, OUTPUT), + DEFAULT_PINMUX(DVFS_CLK, CLDVFS, NORMAL, NORMAL, OUTPUT), + + /* ULPI pinmux */ + DEFAULT_PINMUX(ULPI_DATA0, ULPI, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(ULPI_DATA1, ULPI, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(ULPI_DATA2, ULPI, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(ULPI_DATA3, ULPI, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(ULPI_DATA4, ULPI, UP, NORMAL, INPUT), + DEFAULT_PINMUX(ULPI_DATA5, ULPI, UP, NORMAL, INPUT), + DEFAULT_PINMUX(ULPI_DATA6, ULPI, NORMAL, NORMAL, INPUT), + + /* EC KBC/SPI */ + DEFAULT_PINMUX(ULPI_CLK, SPI1, UP, NORMAL, INPUT), + DEFAULT_PINMUX(ULPI_DIR, SPI1, UP, NORMAL, INPUT), + DEFAULT_PINMUX(ULPI_NXT, SPI1, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(ULPI_STP, SPI1, NORMAL, NORMAL, INPUT), + + /* I2C3 (TPM) pinmux */ + I2C_PINMUX(CAM_I2C_SCL, I2C3, NORMAL, NORMAL, INPUT, DEFAULT, DISABLE), + I2C_PINMUX(CAM_I2C_SDA, I2C3, NORMAL, NORMAL, INPUT, DEFAULT, DISABLE), + + /* I2C2 pinmux */ + I2C_PINMUX(GEN2_I2C_SCL, I2C2, NORMAL, NORMAL, INPUT, DEFAULT, DISABLE), + I2C_PINMUX(GEN2_I2C_SDA, I2C2, NORMAL, NORMAL, INPUT, DEFAULT, DISABLE), + + /* UARTD pinmux (UART4 on Servo board, unused) */ + DEFAULT_PINMUX(GPIO_PJ7, UARTD, NORMAL, NORMAL, OUTPUT), + DEFAULT_PINMUX(GPIO_PB0, UARTD, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(GPIO_PB1, UARTD, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(GPIO_PK7, UARTD, NORMAL, NORMAL, OUTPUT), + + /* SPI4 (Winbond 'boot ROM') */ + DEFAULT_PINMUX(GPIO_PG5, SPI4, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(GPIO_PG6, SPI4, UP, NORMAL, INPUT), + DEFAULT_PINMUX(GPIO_PG7, SPI4, UP, NORMAL, INPUT), + DEFAULT_PINMUX(GPIO_PI3, SPI4, NORMAL, NORMAL, INPUT), + + /* Touch IRQ */ + DEFAULT_PINMUX(GPIO_W3_AUD, RSVD1, NORMAL, NORMAL, INPUT), + + /* PWM1 pinmux */ + DEFAULT_PINMUX(GPIO_PH1, PWM1, NORMAL, NORMAL, OUTPUT), + + /* SDMMC1 pinmux */ + DEFAULT_PINMUX(SDMMC1_CLK, SDMMC1, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC1_CMD, SDMMC1, UP, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC1_DAT0, SDMMC1, UP, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC1_DAT1, SDMMC1, UP, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC1_DAT2, SDMMC1, UP, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC1_DAT3, SDMMC1, UP, NORMAL, INPUT), + + /* SDMMC3 pinmux */ + DEFAULT_PINMUX(SDMMC3_CLK, SDMMC3, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC3_CMD, SDMMC3, UP, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC3_DAT0, SDMMC3, UP, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC3_DAT1, SDMMC3, UP, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC3_DAT2, SDMMC3, UP, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC3_DAT3, SDMMC3, UP, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC3_CLK_LB_IN, SDMMC3, UP, TRISTATE, INPUT), + DEFAULT_PINMUX(SDMMC3_CLK_LB_OUT, SDMMC3, DOWN, NORMAL, INPUT), + + /* SDMMC4 pinmux */ + DEFAULT_PINMUX(SDMMC4_CLK, SDMMC4, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC4_CMD, SDMMC4, UP, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC4_DAT0, SDMMC4, UP, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC4_DAT1, SDMMC4, UP, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC4_DAT2, SDMMC4, UP, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC4_DAT3, SDMMC4, UP, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC4_DAT4, SDMMC4, UP, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC4_DAT5, SDMMC4, UP, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC4_DAT6, SDMMC4, UP, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC4_DAT7, SDMMC4, UP, NORMAL, INPUT), + + /* BLINK pinmux */ + DEFAULT_PINMUX(CLK_32K_OUT, BLINK, NORMAL, NORMAL, OUTPUT), + + /* KBC pinmux */ + DEFAULT_PINMUX(KB_COL0, KBC, UP, NORMAL, INPUT), + DEFAULT_PINMUX(KB_COL1, KBC, UP, NORMAL, INPUT), + DEFAULT_PINMUX(KB_COL2, KBC, UP, NORMAL, INPUT), + DEFAULT_PINMUX(KB_ROW0, KBC, UP, NORMAL, INPUT), + DEFAULT_PINMUX(KB_ROW1, KBC, UP, NORMAL, INPUT), + + /* Misc */ + DEFAULT_PINMUX(GPIO_PV0, RSVD1, NORMAL, TRISTATE, OUTPUT), + DEFAULT_PINMUX(KB_ROW7, RSVD1, UP, NORMAL, INPUT), + + /* UARTA pinmux (BR_UART_TXD/RXD on Servo board) */ + DEFAULT_PINMUX(KB_ROW9, UARTA, UP, NORMAL, OUTPUT), + DEFAULT_PINMUX(KB_ROW10, UARTA, UP, TRISTATE, INPUT), + + /* I2CPWR pinmux (I2C5) */ + I2C_PINMUX(PWR_I2C_SCL, I2CPWR, NORMAL, NORMAL, INPUT, DEFAULT, DISABLE), + I2C_PINMUX(PWR_I2C_SDA, I2CPWR, NORMAL, NORMAL, INPUT, DEFAULT, DISABLE), + + /* RTCK pinmux */ + DEFAULT_PINMUX(JTAG_RTCK, RTCK, NORMAL, NORMAL, INPUT), + + /* CLK pinmux */ + DEFAULT_PINMUX(CLK_32K_IN, CLK, NORMAL, TRISTATE, INPUT), + + /* PWRON pinmux */ + DEFAULT_PINMUX(CORE_PWR_REQ, PWRON, NORMAL, NORMAL, OUTPUT), + + /* CPU pinmux */ + DEFAULT_PINMUX(CPU_PWR_REQ, CPU, NORMAL, NORMAL, OUTPUT), + + /* PMI pinmux */ + DEFAULT_PINMUX(PWR_INT_N, PMI, NORMAL, TRISTATE, INPUT), + + /* RESET_OUT_N pinmux */ + DEFAULT_PINMUX(RESET_OUT_N, RESET_OUT_N, NORMAL, NORMAL, OUTPUT), + + /* EXTPERIPH3 pinmux */ + DEFAULT_PINMUX(CLK3_OUT, EXTPERIPH3, NORMAL, NORMAL, OUTPUT), + + /* I2C1 pinmux */ + I2C_PINMUX(GEN1_I2C_SCL, I2C1, NORMAL, NORMAL, INPUT, DEFAULT, DISABLE), + I2C_PINMUX(GEN1_I2C_SDA, I2C1, NORMAL, NORMAL, INPUT, DEFAULT, DISABLE), + + /* UARTB, GPS */ + DEFAULT_PINMUX(UART2_CTS_N, UARTB, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(UART2_RTS_N, UARTB, NORMAL, NORMAL, OUTPUT), + DEFAULT_PINMUX(UART2_RXD, UARTB, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(UART2_TXD, UARTB, NORMAL, NORMAL, OUTPUT), + + /* UARTC (WIFI/BT) */ + DEFAULT_PINMUX(UART3_CTS_N, UARTC, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(UART3_RTS_N, UARTC, NORMAL, NORMAL, OUTPUT), + DEFAULT_PINMUX(UART3_RXD, UARTC, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(UART3_TXD, UARTC, NORMAL, NORMAL, OUTPUT), + + /* CEC pinmux */ + CEC_PINMUX(HDMI_CEC, CEC, NORMAL, NORMAL, INPUT, DEFAULT, DISABLE), + + /* I2C4 (HDMI_DDC) pinmux */ + DDC_PINMUX(DDC_SCL, I2C4, NORMAL, NORMAL, INPUT, DEFAULT, HIGH), + DDC_PINMUX(DDC_SDA, I2C4, NORMAL, NORMAL, INPUT, DEFAULT, HIGH), + + /* USB pinmux */ + USB_PINMUX(USB_VBUS_EN0, USB, NORMAL, NORMAL, INPUT, DEFAULT, ENABLE), + USB_PINMUX(USB_VBUS_EN1, USB, NORMAL, NORMAL, INPUT, DEFAULT, ENABLE), + + /* Unused, marked SNN_ on schematic, TRISTATE 'em */ + DEFAULT_PINMUX(GPIO_PBB0, RSVD3, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(GPIO_PBB3, RSVD3, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(GPIO_PBB4, RSVD3, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(GPIO_PBB5, RSVD2, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(GPIO_PBB6, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(GPIO_PBB7, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(GPIO_PCC1, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(GPIO_PCC2, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(GPIO_PH3, GMI, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(GPIO_PI7, GMI, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(GPIO_PJ2, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(GPIO_X5_AUD, RSVD3, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(GPIO_X6_AUD, GMI, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(GPIO_W2_AUD, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(GPIO_PFF2, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(USB_VBUS_EN2, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(KB_COL5, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(KB_ROW2, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(KB_ROW3, KBC, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(KB_ROW5, RSVD2, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(KB_ROW6, KBC, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(KB_ROW13, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(KB_ROW14, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(KB_ROW16, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(OWR, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(ULPI_DATA7, ULPI, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(DAP3_DIN, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(DAP3_FS, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(DAP3_SCLK, RSVD2, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(CLK2_OUT, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(SDMMC1_WP_N, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(CAM_MCLK, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(CLK3_REQ, RSVD1, NORMAL, TRISTATE, INPUT), + DEFAULT_PINMUX(SPDIF_OUT, RSVD1, NORMAL, TRISTATE, INPUT), +}; + +static struct pingroup_config unused_pins_lowpower[] = { + DEFAULT_PINMUX(CLK1_REQ, RSVD3, DOWN, TRISTATE, OUTPUT), +}; + +/* Initially setting all used GPIO's to non-TRISTATE */ +static struct pingroup_config tegra124_pinmux_set_nontristate[] = { + DEFAULT_PINMUX(GPIO_X4_AUD, RSVD1, DOWN, NORMAL, OUTPUT), + DEFAULT_PINMUX(GPIO_X7_AUD, RSVD1, DOWN, NORMAL, OUTPUT), + DEFAULT_PINMUX(GPIO_W2_AUD, RSVD1, UP, NORMAL, INPUT), + DEFAULT_PINMUX(GPIO_X3_AUD, RSVD3, UP, NORMAL, INPUT), + + /* EN_VDD_BL */ + DEFAULT_PINMUX(DAP3_DOUT, I2S2, DOWN, NORMAL, OUTPUT), + + /* MODEM */ + DEFAULT_PINMUX(GPIO_PV0, RSVD3, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(GPIO_PV1, RSVD1, NORMAL, NORMAL, INPUT), + + /* BOOT_SEL0-3 */ + DEFAULT_PINMUX(GPIO_PG0, GMI, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(GPIO_PG1, GMI, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(GPIO_PG2, GMI, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(GPIO_PG3, GMI, NORMAL, NORMAL, INPUT), + + DEFAULT_PINMUX(CLK2_REQ, RSVD3, NORMAL, NORMAL, OUTPUT), + + DEFAULT_PINMUX(KB_COL3, KBC, UP, NORMAL, OUTPUT), + DEFAULT_PINMUX(KB_COL4, SDMMC3, UP, NORMAL, INPUT), + DEFAULT_PINMUX(KB_COL6, KBC, UP, NORMAL, OUTPUT), + DEFAULT_PINMUX(KB_COL7, KBC, UP, NORMAL, OUTPUT), + DEFAULT_PINMUX(KB_ROW4, KBC, DOWN, NORMAL, INPUT), + DEFAULT_PINMUX(KB_ROW8, KBC, UP, NORMAL, INPUT), + + DEFAULT_PINMUX(GPIO_PU4, RSVD3, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(GPIO_PU5, RSVD3, NORMAL, NORMAL, OUTPUT), + DEFAULT_PINMUX(GPIO_PU6, RSVD3, NORMAL, NORMAL, INPUT), + + DEFAULT_PINMUX(HDMI_INT, RSVD1, DOWN, NORMAL, INPUT), + DEFAULT_PINMUX(SPDIF_IN, USB, NORMAL, NORMAL, INPUT), + DEFAULT_PINMUX(SDMMC3_CD_N, SDMMC3, UP, NORMAL, INPUT), + + /* TS_SHDN_L */ + DEFAULT_PINMUX(GPIO_PK1, GMI, NORMAL, NORMAL, OUTPUT), +}; + +static struct padctrl_config venice2_padctrl[] = { + /* (_padgrp, _slwf, _slwr, _drvup, _drvdn, _lpmd, _schmt, _hsm) */ + DEFAULT_PADCFG(SDIO3, SDIOCFG_DRVUP_SLWF, SDIOCFG_DRVDN_SLWR, + SDIOCFG_DRVUP, SDIOCFG_DRVDN, NONE, NONE, NONE), +}; +#endif /* PINMUX_CONFIG_VENICE2_H */ diff --git a/board/nvidia/venice2/venice2.c b/board/nvidia/venice2/venice2.c new file mode 100644 index 0000000..1ed2fd7 --- /dev/null +++ b/board/nvidia/venice2/venice2.c @@ -0,0 +1,33 @@ +/* + * (C) Copyright 2013-2014 + * NVIDIA Corporation <www.nvidia.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm-generic/gpio.h> +#include <asm/arch/gpio.h> +#include <asm/arch/gp_padctrl.h> +#include <asm/arch/pinmux.h> +#include "pinmux-config-venice2.h" +#include <i2c.h> + +/* + * Routine: pinmux_init + * Description: Do individual peripheral pinmux configs + */ +void pinmux_init(void) +{ + pinmux_config_table(tegra124_pinmux_set_nontristate, + ARRAY_SIZE(tegra124_pinmux_set_nontristate)); + + pinmux_config_table(tegra124_pinmux_common, + ARRAY_SIZE(tegra124_pinmux_common)); + + pinmux_config_table(unused_pins_lowpower, + ARRAY_SIZE(unused_pins_lowpower)); + + /* Initialize any non-default pad configs (APB_MISC_GP regs) */ + padgrp_config_table(venice2_padctrl, ARRAY_SIZE(venice2_padctrl)); +} diff --git a/board/samsung/common/Makefile b/board/samsung/common/Makefile index 22bd6b1..7d2bb8c 100644 --- a/board/samsung/common/Makefile +++ b/board/samsung/common/Makefile @@ -8,6 +8,7 @@ obj-$(CONFIG_SOFT_I2C_MULTI_BUS) += multi_i2c.o obj-$(CONFIG_THOR_FUNCTION) += thor.o obj-$(CONFIG_CMD_USB_MASS_STORAGE) += ums.o +obj-$(CONFIG_MISC_COMMON) += misc.o ifndef CONFIG_SPL_BUILD obj-$(CONFIG_BOARD_COMMON) += board.o diff --git a/board/samsung/common/dfu_sample_env.txt b/board/samsung/common/dfu_sample_env.txt new file mode 100644 index 0000000..d6ee8a2 --- /dev/null +++ b/board/samsung/common/dfu_sample_env.txt @@ -0,0 +1,9 @@ +mmcboot=setenv bootargs root=/dev/mmcblk${mmcdev}p${mmcrootpart} ${rootfstype} rootwait ${console}; run loaduimage; bootm 0x40007FC0 +rootfstype=ext4 +loaduimage=ext4load mmc ${mmcdev}:${mmcbootpart} 0x40007FC0 uImage +mmcdev=0 +mmcbootpart=2 +mmcrootpart=5 +console=console=ttySAC2,115200n8 +bootcmd=run mmcboot +dfu_alt_info=u-boot mmc 80 800;params.bin mmc 0x38 0x8;uImage ext4 0 2 diff --git a/board/samsung/common/misc.c b/board/samsung/common/misc.c new file mode 100644 index 0000000..eb15739 --- /dev/null +++ b/board/samsung/common/misc.c @@ -0,0 +1,411 @@ +/* + * Copyright (C) 2013 Samsung Electronics + * Przemyslaw Marczak <p.marczak@samsung.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <lcd.h> +#include <libtizen.h> +#include <samsung/misc.h> +#include <errno.h> +#include <version.h> +#include <asm/sizes.h> +#include <asm/arch/cpu.h> +#include <asm/arch/gpio.h> +#include <asm/gpio.h> +#include <linux/input.h> +#include <power/pmic.h> +#include <mmc.h> + +DECLARE_GLOBAL_DATA_PTR; + +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG +void set_board_info(void) +{ + char info[64]; + + snprintf(info, ARRAY_SIZE(info), "%d.%d", s5p_cpu_rev & 0x0f, + (s5p_cpu_rev & 0xf0) >> 0x04); + setenv("soc_rev", info); + + snprintf(info, ARRAY_SIZE(info), "%x", s5p_cpu_id); + setenv("soc_id", info); + +#ifdef CONFIG_REVISION_TAG + snprintf(info, ARRAY_SIZE(info), "%x", get_board_rev()); + setenv("board_rev", info); +#endif +#ifdef CONFIG_OF_LIBFDT + snprintf(info, ARRAY_SIZE(info), "%s%x-%s.dtb", + CONFIG_SYS_SOC, s5p_cpu_id, CONFIG_SYS_BOARD); + setenv("fdtfile", info); +#endif +} +#endif /* CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG */ + +#ifdef CONFIG_LCD_MENU +static int power_key_pressed(u32 reg) +{ + struct pmic *pmic; + u32 status; + u32 mask; + + pmic = pmic_get(KEY_PWR_PMIC_NAME); + if (!pmic) { + printf("%s: Not found\n", KEY_PWR_PMIC_NAME); + return 0; + } + + if (pmic_probe(pmic)) + return 0; + + if (reg == KEY_PWR_STATUS_REG) + mask = KEY_PWR_STATUS_MASK; + else + mask = KEY_PWR_INTERRUPT_MASK; + + if (pmic_reg_read(pmic, reg, &status)) + return 0; + + return !!(status & mask); +} + +static int key_pressed(int key) +{ + int value; + + switch (key) { + case KEY_POWER: + value = power_key_pressed(KEY_PWR_INTERRUPT_REG); + break; + case KEY_VOLUMEUP: + value = !gpio_get_value(KEY_VOL_UP_GPIO); + break; + case KEY_VOLUMEDOWN: + value = !gpio_get_value(KEY_VOL_DOWN_GPIO); + break; + default: + value = 0; + break; + } + + return value; +} + +static int check_keys(void) +{ + int keys = 0; + + if (key_pressed(KEY_POWER)) + keys += KEY_POWER; + if (key_pressed(KEY_VOLUMEUP)) + keys += KEY_VOLUMEUP; + if (key_pressed(KEY_VOLUMEDOWN)) + keys += KEY_VOLUMEDOWN; + + return keys; +} + +/* + * 0 BOOT_MODE_INFO + * 1 BOOT_MODE_THOR + * 2 BOOT_MODE_UMS + * 3 BOOT_MODE_DFU + * 4 BOOT_MODE_EXIT + */ +static char * +mode_name[BOOT_MODE_EXIT + 1] = { + "DEVICE", + "THOR", + "UMS", + "DFU", + "EXIT" +}; + +static char * +mode_info[BOOT_MODE_EXIT + 1] = { + "info", + "downloader", + "mass storage", + "firmware update", + "and run normal boot" +}; + +#define MODE_CMD_ARGC 4 + +static char * +mode_cmd[BOOT_MODE_EXIT + 1][MODE_CMD_ARGC] = { + {"", "", "", ""}, + {"thor", "0", "mmc", "0"}, + {"ums", "0", "mmc", "0"}, + {"dfu", "0", "mmc", "0"}, + {"", "", "", ""}, +}; + +static void display_board_info(void) +{ +#ifdef CONFIG_GENERIC_MMC + struct mmc *mmc = find_mmc_device(0); +#endif + vidinfo_t *vid = &panel_info; + + lcd_position_cursor(4, 4); + + lcd_printf("%s\n\t", U_BOOT_VERSION); + lcd_puts("\n\t\tBoard Info:\n"); +#ifdef CONFIG_SYS_BOARD + lcd_printf("\tBoard name: %s\n", CONFIG_SYS_BOARD); +#endif +#ifdef CONFIG_REVISION_TAG + lcd_printf("\tBoard rev: %u\n", get_board_rev()); +#endif + lcd_printf("\tDRAM banks: %u\n", CONFIG_NR_DRAM_BANKS); + lcd_printf("\tDRAM size: %u MB\n", gd->ram_size / SZ_1M); + +#ifdef CONFIG_GENERIC_MMC + if (mmc) { + if (!mmc->capacity) + mmc_init(mmc); + + lcd_printf("\teMMC size: %llu MB\n", mmc->capacity / SZ_1M); + } +#endif + if (vid) + lcd_printf("\tDisplay resolution: %u x % u\n", + vid->vl_col, vid->vl_row); + + lcd_printf("\tDisplay BPP: %u\n", 1 << vid->vl_bpix); +} + +static int mode_leave_menu(int mode) +{ + char *exit_option; + char *exit_boot = "boot"; + char *exit_back = "back"; + cmd_tbl_t *cmd; + int cmd_result; + int cmd_repeatable; + int leave; + + lcd_clear(); + + switch (mode) { + case BOOT_MODE_EXIT: + return 1; + case BOOT_MODE_INFO: + display_board_info(); + exit_option = exit_back; + leave = 0; + break; + default: + cmd = find_cmd(mode_cmd[mode][0]); + if (cmd) { + printf("Enter: %s %s\n", mode_name[mode], + mode_info[mode]); + lcd_printf("\n\n\t%s %s\n", mode_name[mode], + mode_info[mode]); + lcd_puts("\n\tDo not turn off device before finish!\n"); + + cmd_result = cmd_process(0, MODE_CMD_ARGC, + *(mode_cmd + mode), + &cmd_repeatable, NULL); + + if (cmd_result == CMD_RET_SUCCESS) { + printf("Command finished\n"); + lcd_clear(); + lcd_printf("\n\n\t%s finished\n", + mode_name[mode]); + + exit_option = exit_boot; + leave = 1; + } else { + printf("Command error\n"); + lcd_clear(); + lcd_printf("\n\n\t%s command error\n", + mode_name[mode]); + + exit_option = exit_back; + leave = 0; + } + } else { + lcd_puts("\n\n\tThis mode is not supported.\n"); + exit_option = exit_back; + leave = 0; + } + } + + lcd_printf("\n\n\tPress POWER KEY to %s\n", exit_option); + + /* Clear PWR button Rising edge interrupt status flag */ + power_key_pressed(KEY_PWR_INTERRUPT_REG); + + /* Wait for PWR key */ + while (!key_pressed(KEY_POWER)) + mdelay(1); + + lcd_clear(); + return leave; +} + +static void display_download_menu(int mode) +{ + char *selection[BOOT_MODE_EXIT + 1]; + int i; + + for (i = 0; i <= BOOT_MODE_EXIT; i++) + selection[i] = "[ ]"; + + selection[mode] = "[=>]"; + + lcd_clear(); + lcd_printf("\n\t\tDownload Mode Menu\n"); + + for (i = 0; i <= BOOT_MODE_EXIT; i++) + lcd_printf("\t%s %s - %s\n\n", selection[i], + mode_name[i], + mode_info[i]); +} + +static void download_menu(void) +{ + int mode = 0; + int last_mode = 0; + int run; + int key; + + display_download_menu(mode); + + while (1) { + run = 0; + + if (mode != last_mode) + display_download_menu(mode); + + last_mode = mode; + mdelay(100); + + key = check_keys(); + switch (key) { + case KEY_POWER: + run = 1; + break; + case KEY_VOLUMEUP: + if (mode > 0) + mode--; + break; + case KEY_VOLUMEDOWN: + if (mode < BOOT_MODE_EXIT) + mode++; + break; + default: + break; + } + + if (run) { + if (mode_leave_menu(mode)) + break; + + display_download_menu(mode); + } + } + + lcd_clear(); +} + +static void display_mode_info(void) +{ + lcd_position_cursor(4, 4); + lcd_printf("%s\n", U_BOOT_VERSION); + lcd_puts("\nDownload Mode Menu\n"); +#ifdef CONFIG_SYS_BOARD + lcd_printf("Board name: %s\n", CONFIG_SYS_BOARD); +#endif + lcd_printf("Press POWER KEY to display MENU options."); +} + +static int boot_menu(void) +{ + int key = 0; + int timeout = 10; + + display_mode_info(); + + while (timeout--) { + lcd_printf("\rNormal boot will start in: %d seconds.", timeout); + mdelay(1000); + + key = key_pressed(KEY_POWER); + if (key) + break; + } + + lcd_clear(); + + /* If PWR pressed - show download menu */ + if (key) { + printf("Power pressed - go to download menu\n"); + download_menu(); + printf("Download mode exit.\n"); + } + + return 0; +} + +void check_boot_mode(void) +{ + int pwr_key; + + pwr_key = power_key_pressed(KEY_PWR_STATUS_REG); + if (!pwr_key) + return; + + /* Clear PWR button Rising edge interrupt status flag */ + power_key_pressed(KEY_PWR_INTERRUPT_REG); + + if (key_pressed(KEY_VOLUMEUP)) + boot_menu(); + else if (key_pressed(KEY_VOLUMEDOWN)) + mode_leave_menu(BOOT_MODE_THOR); +} + +void keys_init(void) +{ + /* Set direction to input */ + gpio_direction_input(KEY_VOL_UP_GPIO); + gpio_direction_input(KEY_VOL_DOWN_GPIO); +} +#endif /* CONFIG_LCD_MENU */ + +#ifdef CONFIG_CMD_BMP +void draw_logo(void) +{ + int x, y; + ulong addr; + + addr = panel_info.logo_addr; + if (!addr) { + error("There is no logo data."); + return; + } + + if (panel_info.vl_width >= panel_info.logo_width) { + x = ((panel_info.vl_width - panel_info.logo_width) >> 1); + x += panel_info.logo_x_offset; /* For X center align */ + } else { + x = 0; + printf("Warning: image width is bigger than display width\n"); + } + + if (panel_info.vl_height >= panel_info.logo_height) { + y = ((panel_info.vl_height - panel_info.logo_height) >> 1); + y += panel_info.logo_y_offset; /* For Y center align */ + } else { + y = 0; + printf("Warning: image height is bigger than display height\n"); + } + + bmp_display(addr, x, y); +} +#endif /* CONFIG_CMD_BMP */ diff --git a/board/samsung/dts/exynos5250-smdk5250.dts b/board/samsung/dts/exynos5250-smdk5250.dts index c4ed346..9020382 100644 --- a/board/samsung/dts/exynos5250-smdk5250.dts +++ b/board/samsung/dts/exynos5250-smdk5250.dts @@ -146,6 +146,6 @@ }; ehci@12110000 { - samsung,vbus-gpio = <&gpio 0xbe 0>; /* X26 */ + samsung,vbus-gpio = <&gpio 0x316 0>; /* X26 */ }; }; diff --git a/board/samsung/dts/exynos5250-snow.dts b/board/samsung/dts/exynos5250-snow.dts index 091cdb9..9b48a0c 100644 --- a/board/samsung/dts/exynos5250-snow.dts +++ b/board/samsung/dts/exynos5250-snow.dts @@ -110,11 +110,11 @@ }; ehci@12110000 { - samsung,vbus-gpio = <&gpio 0xb1 0>; /* X11 */ + samsung,vbus-gpio = <&gpio 0x309 0>; /* X11 */ }; xhci@12000000 { - samsung,vbus-gpio = <&gpio 0xbf 0>; /* X27 */ + samsung,vbus-gpio = <&gpio 0x317 0>; /* X27 */ }; tmu@10060000 { diff --git a/board/samsung/goni/goni.c b/board/samsung/goni/goni.c index 366f648..61b9ece 100644 --- a/board/samsung/goni/goni.c +++ b/board/samsung/goni/goni.c @@ -13,10 +13,17 @@ #include <usb/s3c_udc.h> #include <asm/arch/cpu.h> #include <power/max8998_pmic.h> +#include <samsung/misc.h> + DECLARE_GLOBAL_DATA_PTR; static struct s5pc110_gpio *s5pc110_gpio; +u32 get_board_rev(void) +{ + return 0; +} + int board_init(void) { /* Set Initial global variables */ @@ -173,3 +180,13 @@ struct s3c_plat_otg_data s5pc110_otg_data = { .usb_phy_ctrl = S5PC110_USB_PHY_CONTROL, }; #endif + +#ifdef CONFIG_MISC_INIT_R +int misc_init_r(void) +{ +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + set_board_info(); +#endif + return 0; +} +#endif diff --git a/board/samsung/smdk5250/lowlevel_init.S b/board/samsung/smdk5250/lowlevel_init.S deleted file mode 100644 index 9003e2d..0000000 --- a/board/samsung/smdk5250/lowlevel_init.S +++ /dev/null @@ -1,82 +0,0 @@ -/* - * Lowlevel setup for SMDK5250 board based on S5PC520 - * - * Copyright (C) 2012 Samsung Electronics - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <config.h> -#include <version.h> -#include <asm/arch/cpu.h> - -_TEXT_BASE: - .word CONFIG_SYS_TEXT_BASE - - .globl lowlevel_init -lowlevel_init: - - /* use iRAM stack in bl2 */ - ldr sp, =CONFIG_IRAM_STACK - stmdb r13!, {ip,lr} - - /* check reset status */ - ldr r0, =(EXYNOS5_POWER_BASE + INFORM1_OFFSET) - ldr r1, [r0] - - /* AFTR wakeup reset */ - ldr r2, =S5P_CHECK_DIDLE - cmp r1, r2 - beq exit_wakeup - - /* LPA wakeup reset */ - ldr r2, =S5P_CHECK_LPA - cmp r1, r2 - beq exit_wakeup - - /* Sleep wakeup reset */ - ldr r2, =S5P_CHECK_SLEEP - cmp r1, r2 - beq wakeup_reset - - /* - * If U-boot is already running in RAM, no need to relocate U-Boot. - * Memory controller must be configured before relocating U-Boot - * in ram. - */ - ldr r0, =0x0ffffff /* r0 <- Mask Bits*/ - bic r1, pc, r0 /* pc <- current addr of code */ - /* r1 <- unmasked bits of pc */ - ldr r2, _TEXT_BASE /* r2 <- original base addr in ram */ - bic r2, r2, r0 /* r2 <- unmasked bits of r2*/ - cmp r1, r2 /* compare r1, r2 */ - beq 1f /* r0 == r1 then skip sdram init */ - - /* init system clock */ - bl system_clock_init - - /* Memory initialize */ - bl mem_ctrl_init - -1: - bl arch_cpu_init - bl tzpc_init - ldmia r13!, {ip,pc} - -wakeup_reset: - bl system_clock_init - bl mem_ctrl_init - bl arch_cpu_init - bl tzpc_init - -exit_wakeup: - /* Load return address and jump to kernel */ - ldr r0, =(EXYNOS5_POWER_BASE + INFORM0_OFFSET) - - /* r1 = physical address of exynos5_cpu_resume function*/ - ldr r1, [r0] - - /* Jump to kernel */ - mov pc, r1 - nop - nop diff --git a/board/samsung/smdk5250/smdk5250.c b/board/samsung/smdk5250/smdk5250.c index 943c29a..a69f73d 100644 --- a/board/samsung/smdk5250/smdk5250.c +++ b/board/samsung/smdk5250/smdk5250.c @@ -26,22 +26,6 @@ DECLARE_GLOBAL_DATA_PTR; -#ifdef CONFIG_USB_EHCI_EXYNOS -static int board_usb_vbus_init(void) -{ - struct exynos5_gpio_part1 *gpio1 = (struct exynos5_gpio_part1 *) - samsung_get_base_gpio_part1(); - - /* Enable VBUS power switch */ - s5p_gpio_direction_output(&gpio1->x2, 6, 1); - - /* VBUS turn ON time */ - mdelay(3); - - return 0; -} -#endif - #ifdef CONFIG_SOUND_MAX98095 static void board_enable_audio_codec(void) { @@ -56,9 +40,6 @@ static void board_enable_audio_codec(void) int exynos_init(void) { -#ifdef CONFIG_USB_EHCI_EXYNOS - board_usb_vbus_init(); -#endif #ifdef CONFIG_SOUND_MAX98095 board_enable_audio_codec(); #endif diff --git a/board/samsung/trats/trats.c b/board/samsung/trats/trats.c index 640a193..b725505 100644 --- a/board/samsung/trats/trats.c +++ b/board/samsung/trats/trats.c @@ -28,6 +28,7 @@ #include <power/max17042_fg.h> #include <usb.h> #include <usb_mass_storage.h> +#include <samsung/misc.h> #include "setup.h" @@ -742,7 +743,7 @@ vidinfo_t panel_info = { .vl_hsp = CONFIG_SYS_LOW, .vl_vsp = CONFIG_SYS_LOW, .vl_dp = CONFIG_SYS_LOW, - .vl_bpix = 5, /* Bits per pixel, 2^5 = 32 */ + .vl_bpix = 4, /* Bits per pixel, 2^4 = 16 */ /* s6e8ax0 Panel infomation */ .vl_hspw = 5, @@ -786,3 +787,21 @@ void init_panel_info(vidinfo_t *vid) setenv("lcdinfo", "lcd=s6e8ax0"); } + +#ifdef CONFIG_MISC_INIT_R +int misc_init_r(void) +{ +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + set_board_info(); +#endif +#ifdef CONFIG_LCD_MENU + keys_init(); + check_boot_mode(); +#endif +#ifdef CONFIG_CMD_BMP + if (panel_info.logo_on) + draw_logo(); +#endif + return 0; +} +#endif diff --git a/board/samsung/trats2/trats2.c b/board/samsung/trats2/trats2.c index be15357..c17c24d 100644 --- a/board/samsung/trats2/trats2.c +++ b/board/samsung/trats2/trats2.c @@ -28,6 +28,7 @@ #include <usb.h> #include <usb/s3c_udc.h> #include <usb_mass_storage.h> +#include <samsung/misc.h> DECLARE_GLOBAL_DATA_PTR; @@ -72,15 +73,12 @@ static void check_hw_revision(void) int checkboard(void) { puts("Board:\tTRATS2\n"); + printf("HW Revision:\t0x%04x\n", board_rev); + return 0; } #endif -static void show_hw_revision(void) -{ - printf("HW Revision:\t0x%04x\n", board_rev); -} - u32 get_board_rev(void) { return board_rev; @@ -144,17 +142,17 @@ static void board_init_i2c(void) int get_soft_i2c_scl_pin(void) { if (I2C_ADAP_HWNR) - return exynos4x12_gpio_part2_get_nr(m2, 1); /* I2C9 */ + return exynos4x12_gpio_get(2, m2, 1); /* I2C9 */ else - return exynos4x12_gpio_part1_get_nr(f1, 4); /* I2C8 */ + return exynos4x12_gpio_get(1, f1, 4); /* I2C8 */ } int get_soft_i2c_sda_pin(void) { if (I2C_ADAP_HWNR) - return exynos4x12_gpio_part2_get_nr(m2, 0); /* I2C9 */ + return exynos4x12_gpio_get(2, m2, 0); /* I2C9 */ else - return exynos4x12_gpio_part1_get_nr(f1, 5); /* I2C8 */ + return exynos4x12_gpio_get(1, f1, 5); /* I2C8 */ } #endif @@ -568,7 +566,7 @@ vidinfo_t panel_info = { .vl_hsp = CONFIG_SYS_LOW, .vl_vsp = CONFIG_SYS_LOW, .vl_dp = CONFIG_SYS_LOW, - .vl_bpix = 5, /* Bits per pixel, 2^5 = 32 */ + .vl_bpix = 4, /* Bits per pixel, 2^4 = 16 */ /* s6e8ax0 Panel infomation */ .vl_hspw = 5, @@ -618,11 +616,17 @@ void init_panel_info(vidinfo_t *vid) #ifdef CONFIG_MISC_INIT_R int misc_init_r(void) { - setenv("model", "GT-I8800"); - setenv("board", "TRATS2"); - - show_hw_revision(); - +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + set_board_info(); +#endif +#ifdef CONFIG_LCD_MENU + keys_init(); + check_boot_mode(); +#endif +#ifdef CONFIG_CMD_BMP + if (panel_info.logo_on) + draw_logo(); +#endif return 0; } #endif diff --git a/board/samsung/universal_c210/universal.c b/board/samsung/universal_c210/universal.c index 3feef3f..96da7e0 100644 --- a/board/samsung/universal_c210/universal.c +++ b/board/samsung/universal_c210/universal.c @@ -22,6 +22,7 @@ #include <usb/s3c_udc.h> #include <asm/arch/cpu.h> #include <power/max8998_pmic.h> +#include <samsung/misc.h> DECLARE_GLOBAL_DATA_PTR; @@ -446,7 +447,7 @@ vidinfo_t panel_info = { .vl_vsp = CONFIG_SYS_HIGH, .vl_dp = CONFIG_SYS_HIGH, - .vl_bpix = 5, /* Bits per pixel */ + .vl_bpix = 4, /* Bits per pixel */ /* LD9040 LCD Panel */ .vl_hspw = 2, @@ -511,3 +512,21 @@ int board_init(void) return 0; } + +#ifdef CONFIG_MISC_INIT_R +int misc_init_r(void) +{ +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + set_board_info(); +#endif +#ifdef CONFIG_LCD_MENU + keys_init(); + check_boot_mode(); +#endif +#ifdef CONFIG_CMD_BMP + if (panel_info.logo_on) + draw_logo(); +#endif + return 0; +} +#endif diff --git a/board/spear/spear300/spear300.c b/board/spear/spear300/spear300.c index e25aba2..6b6bd9f 100644 --- a/board/spear/spear300/spear300.c +++ b/board/spear/spear300/spear300.c @@ -53,8 +53,7 @@ int board_eth_init(bd_t *bis) #if defined(CONFIG_DESIGNWARE_ETH) u32 interface = PHY_INTERFACE_MODE_MII; - if (designware_initialize(0, CONFIG_SPEAR_ETHBASE, CONFIG_DW0_PHY, - interface) >= 0) + if (designware_initialize(CONFIG_SPEAR_ETHBASE, interface) >= 0) ret++; #endif return ret; diff --git a/board/spear/spear310/spear310.c b/board/spear/spear310/spear310.c index 70f9aa1..a4c6a8e 100644 --- a/board/spear/spear310/spear310.c +++ b/board/spear/spear310/spear310.c @@ -54,8 +54,7 @@ int board_eth_init(bd_t *bis) #if defined(CONFIG_DESIGNWARE_ETH) u32 interface = PHY_INTERFACE_MODE_MII; - if (designware_initialize(0, CONFIG_SPEAR_ETHBASE, CONFIG_DW0_PHY, - interface) >= 0) + if (designware_initialize(CONFIG_SPEAR_ETHBASE, interface) >= 0) ret++; #endif #if defined(CONFIG_MACB) diff --git a/board/spear/spear320/spear320.c b/board/spear/spear320/spear320.c index f6b1fdd..ab732a7 100644 --- a/board/spear/spear320/spear320.c +++ b/board/spear/spear320/spear320.c @@ -65,8 +65,7 @@ int board_eth_init(bd_t *bis) #if defined(CONFIG_DESIGNWARE_ETH) u32 interface = PHY_INTERFACE_MODE_MII; - if (designware_initialize(0, CONFIG_SPEAR_ETHBASE, CONFIG_DW0_PHY, - interface) >= 0) + if (designware_initialize(CONFIG_SPEAR_ETHBASE, interface) >= 0) ret++; #endif #if defined(CONFIG_MACB) diff --git a/board/spear/spear600/spear600.c b/board/spear/spear600/spear600.c index e996a0e..8472002 100644 --- a/board/spear/spear600/spear600.c +++ b/board/spear/spear600/spear600.c @@ -51,8 +51,7 @@ int board_eth_init(bd_t *bis) #if defined(CONFIG_DW_AUTONEG) interface = PHY_INTERFACE_MODE_GMII; #endif - if (designware_initialize(0, CONFIG_SPEAR_ETHBASE, CONFIG_DW0_PHY, - interface) >= 0) + if (designware_initialize(CONFIG_SPEAR_ETHBASE, interface) >= 0) ret++; #endif return ret; diff --git a/board/spear/x600/x600.c b/board/spear/x600/x600.c index 044d204..b8edfcd 100644 --- a/board/spear/x600/x600.c +++ b/board/spear/x600/x600.c @@ -67,31 +67,32 @@ void board_nand_init(void) fsmc_nand_init(nand); } -int designware_board_phy_init(struct eth_device *dev, int phy_addr, - int (*mii_write)(struct eth_device *, u8, u8, u16), - int dw_reset_phy(struct eth_device *)) +int board_phy_config(struct phy_device *phydev) { /* Extended PHY control 1, select GMII */ - mii_write(dev, phy_addr, 23, 0x0020); + phy_write(phydev, MDIO_DEVAD_NONE, 23, 0x0020); /* Software reset necessary after GMII mode selction */ - dw_reset_phy(dev); + phy_reset(phydev); /* Enable extended page register access */ - mii_write(dev, phy_addr, 31, 0x0001); + phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0001); /* 17e: Enhanced LED behavior, needs to be written twice */ - mii_write(dev, phy_addr, 17, 0x09ff); - mii_write(dev, phy_addr, 17, 0x09ff); + phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff); + phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff); /* 16e: Enhanced LED method select */ - mii_write(dev, phy_addr, 16, 0xe0ea); + phy_write(phydev, MDIO_DEVAD_NONE, 16, 0xe0ea); /* Disable extended page register access */ - mii_write(dev, phy_addr, 31, 0x0000); + phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0000); /* Enable clock output pin */ - mii_write(dev, phy_addr, 18, 0x0049); + phy_write(phydev, MDIO_DEVAD_NONE, 18, 0x0049); + + if (phydev->drv->config) + phydev->drv->config(phydev); return 0; } @@ -100,7 +101,7 @@ int board_eth_init(bd_t *bis) { int ret = 0; - if (designware_initialize(0, CONFIG_SPEAR_ETHBASE, CONFIG_PHY_ADDR, + if (designware_initialize(CONFIG_SPEAR_ETHBASE, PHY_INTERFACE_MODE_GMII) >= 0) ret++; diff --git a/board/synopsys/arcangel4/Makefile b/board/synopsys/arcangel4/Makefile new file mode 100644 index 0000000..575e58f --- /dev/null +++ b/board/synopsys/arcangel4/Makefile @@ -0,0 +1,11 @@ +# +# Copyright (C) 2013-2014 Synopsys, Inc. All rights reserved. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +# This board is mostly used for debugging U-Boot in simulation (ISS). +# The only peripheral which is used on this board is a serial port which +# requires no initialization except those in "include/configs/arcangel4.h". +# And now there's no specific initializations for this board. +# So this Makefile is only required for satisfaction of U-Boot build system. diff --git a/board/synopsys/axs101/Makefile b/board/synopsys/axs101/Makefile new file mode 100644 index 0000000..f0965f7 --- /dev/null +++ b/board/synopsys/axs101/Makefile @@ -0,0 +1,8 @@ +# +# Copyright (C) 2013-2014 Synopsys, Inc. All rights reserved. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += axs101.o +obj-$(CONFIG_CMD_NAND) += nand.o diff --git a/board/synopsys/axs101/axs101.c b/board/synopsys/axs101/axs101.c new file mode 100644 index 0000000..4dbeaea --- /dev/null +++ b/board/synopsys/axs101/axs101.c @@ -0,0 +1,44 @@ +/* + * Copyright (C) 2013-2014 Synopsys, Inc. All rights reserved. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <dwmmc.h> +#include <malloc.h> +#include <netdev.h> +#include <phy.h> + +DECLARE_GLOBAL_DATA_PTR; + +int board_mmc_init(bd_t *bis) +{ + struct dwmci_host *host = NULL; + + host = malloc(sizeof(struct dwmci_host)); + if (!host) { + printf("dwmci_host malloc fail!\n"); + return 1; + } + + memset(host, 0, sizeof(struct dwmci_host)); + host->name = "Synopsys Mobile storage"; + host->ioaddr = (void *)ARC_DWMMC_BASE; + host->buswidth = 4; + host->dev_index = 0; + host->bus_hz = 25000000; + + add_dwmci(host, 52000000, 400000); + + return 0; +} + +int board_eth_init(bd_t *bis) +{ + if (designware_initialize(0, ARC_DWGMAC_BASE, 0, + PHY_INTERFACE_MODE_RGMII) >= 0) + return 1; + + return 0; +} diff --git a/board/synopsys/axs101/nand.c b/board/synopsys/axs101/nand.c new file mode 100644 index 0000000..8672803 --- /dev/null +++ b/board/synopsys/axs101/nand.c @@ -0,0 +1,226 @@ +/* + * Copyright (C) 2013-2014 Synopsys, Inc. All rights reserved. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <bouncebuf.h> +#include <common.h> +#include <malloc.h> +#include <nand.h> +#include <asm/io.h> + +#define BUS_WIDTH 8 /* AXI data bus width in bytes */ + +/* DMA buffer descriptor bits & masks */ +#define BD_STAT_OWN (1 << 31) +#define BD_STAT_BD_FIRST (1 << 3) +#define BD_STAT_BD_LAST (1 << 2) +#define BD_SIZES_BUFFER1_MASK 0xfff + +#define BD_STAT_BD_COMPLETE (BD_STAT_BD_FIRST | BD_STAT_BD_LAST) + +/* Controller command flags */ +#define B_WFR (1 << 19) /* 1b - Wait for ready */ +#define B_LC (1 << 18) /* 1b - Last cycle */ +#define B_IWC (1 << 13) /* 1b - Interrupt when complete */ + +/* NAND cycle types */ +#define B_CT_ADDRESS (0x0 << 16) /* Address operation */ +#define B_CT_COMMAND (0x1 << 16) /* Command operation */ +#define B_CT_WRITE (0x2 << 16) /* Write operation */ +#define B_CT_READ (0x3 << 16) /* Write operation */ + +enum nand_isr_t { + NAND_ISR_DATAREQUIRED = 0, + NAND_ISR_TXUNDERFLOW, + NAND_ISR_TXOVERFLOW, + NAND_ISR_DATAAVAILABLE, + NAND_ISR_RXUNDERFLOW, + NAND_ISR_RXOVERFLOW, + NAND_ISR_TXDMACOMPLETE, + NAND_ISR_RXDMACOMPLETE, + NAND_ISR_DESCRIPTORUNAVAILABLE, + NAND_ISR_CMDDONE, + NAND_ISR_CMDAVAILABLE, + NAND_ISR_CMDERROR, + NAND_ISR_DATATRANSFEROVER, + NAND_ISR_NONE +}; + +enum nand_regs_t { + AC_FIFO = 0, /* address and command fifo */ + IDMAC_BDADDR = 0x18, /* idmac descriptor list base address */ + INT_STATUS = 0x118, /* interrupt status register */ + INT_CLR_STATUS = 0x120, /* interrupt clear status register */ +}; + +struct nand_bd { + uint32_t status; /* DES0 */ + uint32_t sizes; /* DES1 */ + uint32_t buffer_ptr0; /* DES2 */ + uint32_t buffer_ptr1; /* DES3 */ +}; + +#define NAND_REG_WRITE(r, v) writel(v, CONFIG_SYS_NAND_BASE + r) +#define NAND_REG_READ(r) readl(CONFIG_SYS_NAND_BASE + r) + +static struct nand_bd *bd; /* DMA buffer descriptors */ + +/** + * axs101_nand_write_buf - write buffer to chip + * @mtd: MTD device structure + * @buf: data buffer + * @len: number of bytes to write + */ +static uint32_t nand_flag_is_set(uint32_t flag) +{ + uint32_t reg = NAND_REG_READ(INT_STATUS); + + if (reg & (1 << NAND_ISR_CMDERROR)) + return 0; + + if (reg & (1 << flag)) { + NAND_REG_WRITE(INT_CLR_STATUS, 1 << flag); + return 1; + } + + return 0; +} + +/** + * axs101_nand_write_buf - write buffer to chip + * @mtd: MTD device structure + * @buf: data buffer + * @len: number of bytes to write + */ +static void axs101_nand_write_buf(struct mtd_info *mtd, const u_char *buf, + int len) +{ + struct bounce_buffer bbstate; + + bounce_buffer_start(&bbstate, (void *)buf, len, GEN_BB_READ); + + /* Setup buffer descriptor */ + writel(BD_STAT_OWN | BD_STAT_BD_COMPLETE, &bd->status); + writel(ALIGN(len, BUS_WIDTH) & BD_SIZES_BUFFER1_MASK, &bd->sizes); + writel(bbstate.bounce_buffer, &bd->buffer_ptr0); + writel(0, &bd->buffer_ptr1); + + /* Issue "write" command */ + NAND_REG_WRITE(AC_FIFO, B_CT_WRITE | B_WFR | B_IWC | B_LC | (len-1)); + + /* Wait for NAND command and DMA to complete */ + while (!nand_flag_is_set(NAND_ISR_CMDDONE)) + ; + while (!nand_flag_is_set(NAND_ISR_TXDMACOMPLETE)) + ; + + bounce_buffer_stop(&bbstate); +} + +/** + * axs101_nand_read_buf - read chip data into buffer + * @mtd: MTD device structure + * @buf: buffer to store data + * @len: number of bytes to read + */ +static void axs101_nand_read_buf(struct mtd_info *mtd, u_char *buf, int len) +{ + struct bounce_buffer bbstate; + + bounce_buffer_start(&bbstate, buf, len, GEN_BB_WRITE); + + /* Setup buffer descriptor */ + writel(BD_STAT_OWN | BD_STAT_BD_COMPLETE, &bd->status); + writel(ALIGN(len, BUS_WIDTH) & BD_SIZES_BUFFER1_MASK, &bd->sizes); + writel(bbstate.bounce_buffer, &bd->buffer_ptr0); + writel(0, &bd->buffer_ptr1); + + /* Issue "read" command */ + NAND_REG_WRITE(AC_FIFO, B_CT_READ | B_WFR | B_IWC | B_LC | (len - 1)); + + /* Wait for NAND command and DMA to complete */ + while (!nand_flag_is_set(NAND_ISR_CMDDONE)) + ; + while (!nand_flag_is_set(NAND_ISR_RXDMACOMPLETE)) + ; + + bounce_buffer_stop(&bbstate); +} + +/** + * axs101_nand_read_byte - read one byte from the chip + * @mtd: MTD device structure + */ +static u_char axs101_nand_read_byte(struct mtd_info *mtd) +{ + u8 byte; + + axs101_nand_read_buf(mtd, (uchar *)&byte, sizeof(byte)); + return byte; +} + +/** + * axs101_nand_read_word - read one word from the chip + * @mtd: MTD device structure + */ +static u16 axs101_nand_read_word(struct mtd_info *mtd) +{ + u16 word; + + axs101_nand_read_buf(mtd, (uchar *)&word, sizeof(word)); + return word; +} + +/** + * axs101_nand_hwcontrol - NAND control functions wrapper. + * @mtd: MTD device structure + * @cmd: Command + */ +static void axs101_nand_hwcontrol(struct mtd_info *mtdinfo, int cmd, + unsigned int ctrl) +{ + if (cmd == NAND_CMD_NONE) + return; + + cmd = cmd & 0xff; + + switch (ctrl & (NAND_ALE | NAND_CLE)) { + /* Address */ + case NAND_ALE: + cmd |= B_CT_ADDRESS; + break; + + /* Command */ + case NAND_CLE: + cmd |= B_CT_COMMAND | B_WFR; + + break; + + default: + debug("%s: unknown ctrl %#x\n", __func__, ctrl); + } + + NAND_REG_WRITE(AC_FIFO, cmd | B_LC); + while (!nand_flag_is_set(NAND_ISR_CMDDONE)) + ; +} + +int board_nand_init(struct nand_chip *nand) +{ + bd = (struct nand_bd *)memalign(ARCH_DMA_MINALIGN, + sizeof(struct nand_bd)); + + /* Set buffer descriptor address in IDMAC */ + NAND_REG_WRITE(IDMAC_BDADDR, bd); + + nand->ecc.mode = NAND_ECC_SOFT; + nand->cmd_ctrl = axs101_nand_hwcontrol; + nand->read_byte = axs101_nand_read_byte; + nand->read_word = axs101_nand_read_word; + nand->write_buf = axs101_nand_write_buf; + nand->read_buf = axs101_nand_read_buf; + + return 0; +} diff --git a/board/ti/dra7xx/README b/board/ti/dra7xx/README new file mode 100644 index 0000000..2fdaeac --- /dev/null +++ b/board/ti/dra7xx/README @@ -0,0 +1,25 @@ +Summary +======= + +This document covers various features of the 'dra7xx_evm' build and some +related uses. + +eMMC boot partition use +======================= + +It is possible, depending on SYSBOOT configuration to boot from the eMMC +boot partitions using (name depending on documentation referenced) +Alternative Boot operation mode or Boot Sequence Option 1/2. In this +example we load MLO and u-boot.img from the build into DDR and then use +'mmc bootbus' to set the required rate (see TRM) and 'mmc partconfig' to +set boot0 as the boot device. +U-Boot # setenv autoload no +U-Boot # usb start +U-Boot # dhcp +U-Boot # mmc dev 1 1 +U-Boot # tftp ${loadaddr} dra7xx/MLO +U-Boot # mmc write ${loadaddr} 0 100 +U-Boot # tftp ${loadaddr} dra7xx/u-boot.img +U-Boot # mmc write ${loadaddr} 300 400 +U-Boot # mmc bootbus 1 2 0 2 +U-Boot # mmc partconf 1 1 1 0 diff --git a/board/ti/omap5_uevm/README b/board/ti/omap5_uevm/README new file mode 100644 index 0000000..970e2ec --- /dev/null +++ b/board/ti/omap5_uevm/README @@ -0,0 +1,25 @@ +Summary +======= + +This document covers various features of the 'omap5_uevm' build and some +related uses. + +eMMC boot partition use +======================= + +It is possible, depending on SYSBOOT configuration to boot from the eMMC +boot partitions using (name depending on documentation referenced) +Alternative Boot operation mode or Boot Sequence Option 1/2. In this +example we load MLO and u-boot.img from the build into DDR and then use +'mmc bootbus' to set the required rate (see TRM) and 'mmc partconfig' to +set boot0 as the boot device. +U-Boot # setenv autoload no +U-Boot # usb start +U-Boot # dhcp +U-Boot # mmc dev 1 1 +U-Boot # tftp ${loadaddr} omap5uevm/MLO +U-Boot # mmc write ${loadaddr} 0 100 +U-Boot # tftp ${loadaddr} omap5uevm/u-boot.img +U-Boot # mmc write ${loadaddr} 300 400 +U-Boot # mmc bootbus 1 2 0 2 +U-Boot # mmc partconf 1 1 1 0 diff --git a/board/xilinx/zynq/Makefile b/board/xilinx/zynq/Makefile index 6301a8c..3f19a1c 100644 --- a/board/xilinx/zynq/Makefile +++ b/board/xilinx/zynq/Makefile @@ -6,3 +6,4 @@ # obj-y := board.o +obj-$(CONFIG_SPL_BUILD) += ps7_init.o diff --git a/board/xilinx/zynq/board.c b/board/xilinx/zynq/board.c index a5b9bde..82f2345 100644 --- a/board/xilinx/zynq/board.c +++ b/board/xilinx/zynq/board.c @@ -12,17 +12,12 @@ DECLARE_GLOBAL_DATA_PTR; -/* Bootmode setting values */ -#define ZYNQ_BM_MASK 0x0F -#define ZYNQ_BM_NOR 0x02 -#define ZYNQ_BM_SD 0x05 -#define ZYNQ_BM_JTAG 0x0 - #ifdef CONFIG_FPGA Xilinx_desc fpga; /* It can be done differently */ Xilinx_desc fpga010 = XILINX_XC7Z010_DESC(0x10); +Xilinx_desc fpga015 = XILINX_XC7Z015_DESC(0x15); Xilinx_desc fpga020 = XILINX_XC7Z020_DESC(0x20); Xilinx_desc fpga030 = XILINX_XC7Z030_DESC(0x30); Xilinx_desc fpga045 = XILINX_XC7Z045_DESC(0x45); @@ -40,6 +35,9 @@ int board_init(void) case XILINX_ZYNQ_7010: fpga = fpga010; break; + case XILINX_ZYNQ_7015: + fpga = fpga015; + break; case XILINX_ZYNQ_7020: fpga = fpga020; break; @@ -55,8 +53,6 @@ int board_init(void) } #endif - icache_enable(); - #ifdef CONFIG_FPGA fpga_init(); fpga_add(fpga_xilinx, &fpga); @@ -85,7 +81,6 @@ int board_late_init(void) return 0; } -#ifdef CONFIG_CMD_NET int board_eth_init(bd_t *bis) { u32 ret = 0; @@ -119,7 +114,6 @@ int board_eth_init(bd_t *bis) #endif return ret; } -#endif #ifdef CONFIG_CMD_MMC int board_mmc_init(bd_t *bd) diff --git a/board/xilinx/zynq/ps7_init.c b/board/xilinx/zynq/ps7_init.c new file mode 100644 index 0000000..c47da09 --- /dev/null +++ b/board/xilinx/zynq/ps7_init.c @@ -0,0 +1,12 @@ +/* + * (C) Copyright 2014 Xilinx, Inc. Michal Simek + * + * SPDX-License-Identifier: GPL-2.0+ + */ +#include <common.h> +#include <asm/arch/spl.h> + +__weak void ps7_init(void) +{ + puts("Please copy ps7_init.c/h from hw project\n"); +} |