diff options
Diffstat (limited to 'board')
-rw-r--r-- | board/korat/Kconfig | 9 | ||||
-rw-r--r-- | board/korat/MAINTAINERS | 7 | ||||
-rw-r--r-- | board/korat/Makefile | 9 | ||||
-rw-r--r-- | board/korat/README | 64 | ||||
-rw-r--r-- | board/korat/config.mk | 27 | ||||
-rw-r--r-- | board/korat/init.S | 80 | ||||
-rw-r--r-- | board/korat/korat.c | 633 | ||||
-rw-r--r-- | board/korat/u-boot-F7FC.lds | 124 |
8 files changed, 0 insertions, 953 deletions
diff --git a/board/korat/Kconfig b/board/korat/Kconfig deleted file mode 100644 index f434dea..0000000 --- a/board/korat/Kconfig +++ /dev/null @@ -1,9 +0,0 @@ -if TARGET_KORAT - -config SYS_BOARD - default "korat" - -config SYS_CONFIG_NAME - default "korat" - -endif diff --git a/board/korat/MAINTAINERS b/board/korat/MAINTAINERS deleted file mode 100644 index 8b96846..0000000 --- a/board/korat/MAINTAINERS +++ /dev/null @@ -1,7 +0,0 @@ -KORAT BOARD -M: Larry Johnson <lrj@acm.org> -S: Maintained -F: board/korat/ -F: include/configs/korat.h -F: configs/korat_defconfig -F: configs/korat_perm_defconfig diff --git a/board/korat/Makefile b/board/korat/Makefile deleted file mode 100644 index 63914bc..0000000 --- a/board/korat/Makefile +++ /dev/null @@ -1,9 +0,0 @@ -# -# (C) Copyright 2002-2007 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y = korat.o -extra-y += init.o diff --git a/board/korat/README b/board/korat/README deleted file mode 100644 index e059f78..0000000 --- a/board/korat/README +++ /dev/null @@ -1,64 +0,0 @@ -The Korat board has two NOR flashes, FLASH0 and FLASH1, which are connected to -chip select 0 and 1, respectively. FLASH0 contains 16 MiB, and is mapped to -addresses 0xFF000000 - 0xFFFFFFFF as U-Boot Flash Bank #2. FLASH1 contains -from 16 to 128 MiB, and is mapped to 0xF?000000 - 0xF7FFFFFF as U-Boot Flash -Bank #1 (with the starting address depending on the flash size detected at -runtime). The write-enable pin on FLASH0 is disabled, so the contents of FLASH0 -cannot be modified in the field. This also prevents FLASH0 from executing -commands to return chip information, so its configuration is hard-coded in -U-Boot. - -There are two versions of U-Boot for Korat: "permanent" and "upgradable". The -permanent U-Boot is pre-programmed at the top of FLASH0, e.g., at addresses -0xFFFA0000 - 0xFFFFFFFF for the current 384 KiB size. The upgradable U-Boot is -located 256 KiB from the top of FLASH1, e.g. at addresses 0xF7F6000 - 0xF7FC0000 -for the current 384 KiB size. FLASH1 addresses 0xF7FE0000 - 0xF7FF0000 are -used for the U-Boot environmental parameters, and addresses 0xF7FC0000 - -0xF7FDFFFF are used for the redundant copy of the parameters. These locations -are used by both versions of U-Boot. - -On booting, the permanent U-Boot in FLASH0 begins executing. After performing -minimal setup, it monitors the state of the board's Reset switch (GPIO47). If -the switch is sensed as open before a timeout period, then U-Boot branches to -address 0xF7FBFFFC. This causes the upgradable U-Boot to execute from the -beginning. If the switch remains closed thoughout the timeout period, the -permanent U-Boot activates the on-board buzzer until the switch is sensed as -opened. It then continues to execute without branching to FLASH1. The effect -of this is that normally the Korat board boots its upgradable U-Boot, but, if -this has been corrupted, the user can boot the permanent U-Boot, which can then -be used to erase and reload FLASH1 as needed. - -Note that it is not necessary for the permanent U-Boot to have all the latest -features, but only that it have sufficient functionality (working "tftp", -"erase", "cp.b", etc.) to repair FLASH1. Also, the permanent U-Boot makes no -assumptions about the size of FLASH1 or the size of the upgradable U-Boot: it is -sufficient that the upgradable U-Boot can be started by a branch to 0xF7FBFFFC. - -The build sequence: - - make korat_perm_config - make all - -builds the permanent U-Boot by selecting loader file "u-boot.lds" and defining -preprocessor symbol "CONFIG_KORAT_PERMANENT". The default build: - - make korat_config - make all - -creates the upgradable U-Boot by selecting loader file "u-boot-F7FC.lds" and -leaving preprocessor symbol "CONFIG_KORAT_PERMANENT" undefined. - -2008-02-22, Larry Johnson <lrj@acm.org> - - -The CompactFlash(R) controller on the Korat board provides a hi-speed USB -interface. This may be connected to either a dedicated port on the on-board -USB controller, or to a USB port on the PowerPC 440EPx processor. The U-Boot -environment variable "korat_usbcf" can be used to specify which of these two -USB host ports is used for CompactFlash. The valid setting for the variable are -the strings "pci" and "ppc". If the variable defined and set to "ppc", then the -PowerPC USB port is used. In all other cases the on-board USB controller is -used, but if "korat_usbcf" is defined but is set to a string other than the two -valid options, a warning is also issued. - -2009-01-28, Larry Johnson <lrj@acm.org> diff --git a/board/korat/config.mk b/board/korat/config.mk deleted file mode 100644 index 42e0060..0000000 --- a/board/korat/config.mk +++ /dev/null @@ -1,27 +0,0 @@ -# -# (C) Copyright 2002 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# -# -# Korat (PPC440EPx) board -# - -PLATFORM_CPPFLAGS += -DCONFIG_440=1 - -ifeq ($(debug),1) -PLATFORM_CPPFLAGS += -DDEBUG -endif - -ifeq ($(emul),1) -PLATFORM_CPPFLAGS += -fno-schedule-insns -fno-schedule-insns2 -endif - -ifeq ($(dbcr),1) -PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8CFF0000 -endif - -ifndef CONFIG_KORAT_PERMANENT -LDSCRIPT := $(srctree)/board/$(BOARDDIR)/u-boot-F7FC.lds -endif diff --git a/board/korat/init.S b/board/korat/init.S deleted file mode 100644 index 20c5bdd..0000000 --- a/board/korat/init.S +++ /dev/null @@ -1,80 +0,0 @@ -/* - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <asm-offsets.h> -#include <ppc_asm.tmpl> -#include <asm/mmu.h> -#include <config.h> - -/************************************************************************** - * TLB TABLE - * - * This table is used by the cpu boot code to setup the initial tlb - * entries. Rather than make broad assumptions in the cpu source tree, - * this table lets each board set things up however they like. - * - * Pointer to the table is returned in r1 - * - *************************************************************************/ - .section .bootpg,"ax" - .globl tlbtab - -tlbtab: - tlbtab_start - - /* - * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the - * speed up boot process. It is patched after relocation to enable SA_I - */ - tlbentry( 0xF0000000, SZ_256M, 0xF0000000, 1, AC_RWX | SA_G ) - - /* - * TLB entries for SDRAM are not needed on this platform. They are - * generated dynamically in the SPD DDR2 detection routine. - */ - -#ifdef CONFIG_SYS_INIT_RAM_DCACHE - /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ - tlbentry( CONFIG_SYS_INIT_RAM_ADDR, SZ_64K, CONFIG_SYS_INIT_RAM_ADDR, 0, - AC_RWX | SA_G ) -#endif - - /* TLB-entry for PCI Memory */ - tlbentry( CONFIG_SYS_PCI_MEMBASE + 0x00000000, SZ_256M, - CONFIG_SYS_PCI_MEMBASE + 0x00000000, 1, AC_RW | SA_IG ) - - tlbentry( CONFIG_SYS_PCI_MEMBASE + 0x10000000, SZ_256M, - CONFIG_SYS_PCI_MEMBASE + 0x10000000, 1, AC_RW | SA_IG ) - - tlbentry( CONFIG_SYS_PCI_MEMBASE + 0x20000000, SZ_256M, - CONFIG_SYS_PCI_MEMBASE + 0x20000000, 1, AC_RW | SA_IG ) - - tlbentry( CONFIG_SYS_PCI_MEMBASE + 0x30000000, SZ_256M, - CONFIG_SYS_PCI_MEMBASE + 0x30000000, 1, AC_RW | SA_IG ) - - /* TLB-entry for EBC */ - tlbentry( CONFIG_SYS_CPLD_BASE, SZ_1K, CONFIG_SYS_CPLD_BASE, 1, AC_RW | SA_IG ) - - /* TLB-entry for Internal Registers & OCM */ - /* I wonder why this must be executable -- lrj@acm.org 2007-10-08 */ - tlbentry( 0xE0000000, SZ_16M, 0xE0000000, 0, AC_RWX | SA_I ) - - /*TLB-entry PCI registers*/ - tlbentry( 0xEEC00000, SZ_1K, 0xEEC00000, 1, AC_RW | SA_IG ) - - /* TLB-entry for peripherals */ - tlbentry( 0xEF000000, SZ_16M, 0xEF000000, 1, AC_RW | SA_IG) - - /* TLB-entry PCI IO Space - from sr@denx.de */ - tlbentry(0xE8000000, SZ_64K, 0xE8000000, 1, AC_RW | SA_IG) - - tlbtab_end - -#if defined(CONFIG_KORAT_PERMANENT) - .globl korat_branch_absolute -korat_branch_absolute: - mtlr r3 - blr -#endif diff --git a/board/korat/korat.c b/board/korat/korat.c deleted file mode 100644 index d9ab2fd..0000000 --- a/board/korat/korat.c +++ /dev/null @@ -1,633 +0,0 @@ -/* - * (C) Copyright 2007-2010 - * Larry Johnson, lrj@acm.org - * - * (C) Copyright 2006-2007 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * (C) Copyright 2006 - * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com - * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <fdt_support.h> -#include <i2c.h> -#include <libfdt.h> -#include <asm/ppc440.h> -#include <asm/bitops.h> -#include <asm/ppc4xx-gpio.h> -#include <asm/io.h> -#include <asm/ppc4xx-uic.h> -#include <asm/processor.h> -#include <asm/4xx_pci.h> - -DECLARE_GLOBAL_DATA_PTR; - -extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */ - -ulong flash_get_size(ulong base, int banknum); - -#if defined(CONFIG_KORAT_PERMANENT) -void korat_buzzer(int const on) -{ - if (on) { - out_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x05, - in_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x05) | 0x80); - } else { - out_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x05, - in_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x05) & ~0x80); - } -} -#endif - -int board_early_init_f(void) -{ - uint32_t sdr0_pfc1, sdr0_pfc2; - uint32_t reg; - int eth; - -#if defined(CONFIG_KORAT_PERMANENT) - unsigned mscount; - - extern void korat_branch_absolute(uint32_t addr); - - for (mscount = 0; mscount < CONFIG_SYS_KORAT_MAN_RESET_MS; ++mscount) { - udelay(1000); - if (gpio_read_in_bit(CONFIG_SYS_GPIO_RESET_PRESSED_)) { - /* This call does not return. */ - korat_branch_absolute( - CONFIG_SYS_FLASH1_TOP - 2 * CONFIG_ENV_SECT_SIZE - 4); - } - } - korat_buzzer(1); - while (!gpio_read_in_bit(CONFIG_SYS_GPIO_RESET_PRESSED_)) - udelay(1000); - - korat_buzzer(0); -#endif - - mtdcr(EBC0_CFGADDR, EBC0_CFG); - mtdcr(EBC0_CFGDATA, 0xb8400000); - - /* - * Setup the interrupt controller polarities, triggers, etc. - */ - mtdcr(UIC0SR, 0xffffffff); /* clear all */ - mtdcr(UIC0ER, 0x00000000); /* disable all */ - mtdcr(UIC0CR, 0x00000005); /* ATI & UIC1 crit are critical */ - mtdcr(UIC0PR, 0xfffff7ff); /* per ref-board manual */ - mtdcr(UIC0TR, 0x00000000); /* per ref-board manual */ - mtdcr(UIC0VR, 0x00000000); /* int31 highest, base=0x000 */ - mtdcr(UIC0SR, 0xffffffff); /* clear all */ - - mtdcr(UIC1SR, 0xffffffff); /* clear all */ - mtdcr(UIC1ER, 0x00000000); /* disable all */ - mtdcr(UIC1CR, 0x00000000); /* all non-critical */ - mtdcr(UIC1PR, 0xffffffff); /* per ref-board manual */ - mtdcr(UIC1TR, 0x00000000); /* per ref-board manual */ - mtdcr(UIC1VR, 0x00000000); /* int31 highest, base=0x000 */ - mtdcr(UIC1SR, 0xffffffff); /* clear all */ - - mtdcr(UIC2SR, 0xffffffff); /* clear all */ - mtdcr(UIC2ER, 0x00000000); /* disable all */ - mtdcr(UIC2CR, 0x00000000); /* all non-critical */ - mtdcr(UIC2PR, 0xffffffff); /* per ref-board manual */ - mtdcr(UIC2TR, 0x00000000); /* per ref-board manual */ - mtdcr(UIC2VR, 0x00000000); /* int31 highest, base=0x000 */ - mtdcr(UIC2SR, 0xffffffff); /* clear all */ - - /* - * Take sim card reader and CF controller out of reset. Also enable PHY - * auto-detect until board-specific PHY resets are available. - */ - out_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x02, 0xC0); - - /* Configure the two Ethernet PHYs. For each PHY, configure for fiber - * if the SFP module is present, and for copper if it is not present. - */ - for (eth = 0; eth < 2; ++eth) { - if (gpio_read_in_bit(CONFIG_SYS_GPIO_SFP0_PRESENT_ + eth)) { - /* SFP module not present: configure PHY for copper. */ - /* Set PHY to autonegotate 10 MB, 100MB, or 1 GB */ - out_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x03, - in_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x03) | - 0x06 << (4 * eth)); - } else { - /* SFP module present: configure PHY for fiber and - enable output */ - gpio_write_bit(CONFIG_SYS_GPIO_PHY0_FIBER_SEL + eth, 1); - gpio_write_bit(CONFIG_SYS_GPIO_SFP0_TX_EN_ + eth, 0); - } - } - /* enable Ethernet: set GPIO45 and GPIO46 to 1 */ - gpio_write_bit(CONFIG_SYS_GPIO_PHY0_EN, 1); - gpio_write_bit(CONFIG_SYS_GPIO_PHY1_EN, 1); - - /* Wait 1 ms, then enable Fiber signal detect to PHYs. */ - udelay(1000); - out_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x03, - in_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x03) | 0x88); - - /* select Ethernet (and optionally IIC1) pins */ - mfsdr(SDR0_PFC1, sdr0_pfc1); - sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SELECT_MASK) | - SDR0_PFC1_SELECT_CONFIG_4; -#ifdef CONFIG_I2C_MULTI_BUS - sdr0_pfc1 |= ((sdr0_pfc1 & ~SDR0_PFC1_SIS_MASK) | SDR0_PFC1_SIS_IIC1_SEL); -#endif - mfsdr(SDR0_PFC2, sdr0_pfc2); - sdr0_pfc2 = (sdr0_pfc2 & ~SDR0_PFC2_SELECT_MASK) | - SDR0_PFC2_SELECT_CONFIG_4; - mtsdr(SDR0_PFC2, sdr0_pfc2); - mtsdr(SDR0_PFC1, sdr0_pfc1); - - /* PCI arbiter enabled */ - mfsdr(SDR0_PCI0, reg); - mtsdr(SDR0_PCI0, 0x80000000 | reg); - - return 0; -} - -/* - * The boot flash on CS0 normally has its write-enable pin disabled, and so will - * not respond to CFI commands. This routine therefore fills in the flash - * information for the boot flash. (The flash at CS1 operates normally.) - */ -ulong board_flash_get_legacy (ulong base, int banknum, flash_info_t * info) -{ - uint32_t addr; - int i; - - if (1 != banknum) - return 0; - - info->size = CONFIG_SYS_FLASH0_SIZE; - info->sector_count = CONFIG_SYS_FLASH0_SIZE / 0x20000; - info->flash_id = 0x01000000; - info->portwidth = 2; - info->chipwidth = 2; - info->buffer_size = 32; - info->erase_blk_tout = 16384; - info->write_tout = 2; - info->buffer_write_tout = 5; - info->vendor = 2; - info->cmd_reset = 0x00F0; - info->interface = 2; - info->legacy_unlock = 0; - info->manufacturer_id = 1; - info->device_id = 0x007E; - -#if CONFIG_SYS_FLASH0_SIZE == 0x01000000 - info->device_id2 = 0x2101; -#elif CONFIG_SYS_FLASH0_SIZE == 0x04000000 - info->device_id2 = 0x2301; -#else -#error Unable to set device_id2 for current CONFIG_SYS_FLASH0_SIZE -#endif - - info->ext_addr = 0x0040; - info->cfi_version = 0x3133; - info->cfi_offset = 0x0055; - info->addr_unlock1 = 0x00000555; - info->addr_unlock2 = 0x000002AA; - info->name = "CFI conformant"; - for (i = 0, addr = -info->size; - i < info->sector_count; - ++i, addr += 0x20000) { - info->start[i] = addr; - info->protect[i] = 0x00; - } - return 1; -} - -static int man_data_read(unsigned int addr) -{ - /* - * Read an octet of data from address "addr" in the manufacturer's - * information serial EEPROM, or -1 on error. - */ - u8 data[2]; - - if (0 != i2c_probe(MAN_DATA_EEPROM_ADDR) || - 0 != i2c_read(MAN_DATA_EEPROM_ADDR, addr, 1, data, 1)) { - debug("man_data_read(0x%02X) failed\n", addr); - return -1; - } - debug("man_info_read(0x%02X) returned 0x%02X\n", addr, data[0]); - return data[0]; -} - -static unsigned int man_data_field_addr(unsigned int const field) -{ - /* - * The manufacturer's information serial EEPROM contains a sequence of - * zero-delimited fields. Return the starting address of field "field", - * or 0 on error. - */ - unsigned addr, i; - - if (0 == field || 'A' != man_data_read(0) || '\0' != man_data_read(1)) - /* Only format "A" is currently supported */ - return 0; - - for (addr = 2, i = 1; i < field && addr < 256; ++addr) { - if ('\0' == man_data_read(addr)) - ++i; - } - return (addr < 256) ? addr : 0; -} - -static char *man_data_read_field(char s[], unsigned const field, - unsigned const length) -{ - /* - * Place the null-terminated contents of field "field" of length - * "length" from the manufacturer's information serial EEPROM into - * string "s[length + 1]" and return a pointer to s, or return 0 on - * error. In either case the original contents of s[] is not preserved. - */ - unsigned addr, i; - - addr = man_data_field_addr(field); - if (0 == addr || addr + length >= 255) - return 0; - - for (i = 0; i < length; ++i) { - int const c = man_data_read(addr++); - - if (c <= 0) - return 0; - - s[i] = (char)c; - } - if (0 != man_data_read(addr)) - return 0; - - s[i] = '\0'; - return s; -} - -static void set_serial_number(void) -{ - /* - * If the environmental variable "serial#" is not set, try to set it - * from the manufacturer's information serial EEPROM. - */ - char s[MAN_INFO_LENGTH + MAN_MAC_ADDR_LENGTH + 2]; - - if (getenv("serial#")) - return; - - if (!man_data_read_field(s, MAN_INFO_FIELD, MAN_INFO_LENGTH)) - return; - - s[MAN_INFO_LENGTH] = '-'; - if (!man_data_read_field(s + MAN_INFO_LENGTH + 1, MAN_MAC_ADDR_FIELD, - MAN_MAC_ADDR_LENGTH)) - return; - - setenv("serial#", s); -} - -static void set_mac_addresses(void) -{ - /* - * If the environmental variables "ethaddr" and/or "eth1addr" are not - * set, try to set them from the manufacturer's information serial - * EEPROM. - */ - -#if MAN_MAC_ADDR_LENGTH % 2 != 0 -#error MAN_MAC_ADDR_LENGTH must be an even number -#endif - - char s[(3 * MAN_MAC_ADDR_LENGTH) / 2]; - char *src; - char *dst; - - if (0 != getenv("ethaddr") && 0 != getenv("eth1addr")) - return; - - if (0 == man_data_read_field(s + (MAN_MAC_ADDR_LENGTH / 2) - 1, - MAN_MAC_ADDR_FIELD, MAN_MAC_ADDR_LENGTH)) - return; - - for (src = s + (MAN_MAC_ADDR_LENGTH / 2) - 1, dst = s; src != dst;) { - *dst++ = *src++; - *dst++ = *src++; - *dst++ = ':'; - } - if (0 == getenv("ethaddr")) - setenv("ethaddr", s); - - if (0 == getenv("eth1addr")) { - ++s[((3 * MAN_MAC_ADDR_LENGTH) / 2) - 2]; - setenv("eth1addr", s); - } -} - -int misc_init_r(void) -{ - uint32_t pbcr; - int size_val; - uint32_t reg; - unsigned long usb2d0cr = 0; - unsigned long usb2phy0cr, usb2h0cr = 0; - unsigned long sdr0_pfc1; - uint32_t const flash1_size = gd->bd->bi_flashsize - CONFIG_SYS_FLASH0_SIZE; - char const *const act = getenv("usbact"); - char const *const usbcf = getenv("korat_usbcf"); - - /* - * Re-do FLASH1 sizing and adjust flash start and offset. - */ - gd->bd->bi_flashstart = CONFIG_SYS_FLASH1_TOP - flash1_size; - gd->bd->bi_flashoffset = 0; - - mtdcr(EBC0_CFGADDR, PB1CR); - pbcr = mfdcr(EBC0_CFGDATA); - size_val = ffs(flash1_size) - 21; - pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17); - mtdcr(EBC0_CFGADDR, PB1CR); - mtdcr(EBC0_CFGDATA, pbcr); - - /* - * Re-check to get correct base address - */ - flash_get_size(gd->bd->bi_flashstart, 0); - - /* - * Re-do FLASH1 sizing and adjust flash offset to reserve space for - * environment - */ - gd->bd->bi_flashoffset = - CONFIG_ENV_ADDR_REDUND + CONFIG_ENV_SECT_SIZE - CONFIG_SYS_FLASH1_ADDR; - - mtdcr(EBC0_CFGADDR, PB1CR); - pbcr = mfdcr(EBC0_CFGDATA); - size_val = ffs(gd->bd->bi_flashsize - CONFIG_SYS_FLASH0_SIZE) - 21; - pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17); - mtdcr(EBC0_CFGADDR, PB1CR); - mtdcr(EBC0_CFGDATA, pbcr); - - /* Monitor protection ON by default */ -#if defined(CONFIG_KORAT_PERMANENT) - (void)flash_protect(FLAG_PROTECT_SET, CONFIG_SYS_MONITOR_BASE, - CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN - 1, - flash_info + 1); -#else - (void)flash_protect(FLAG_PROTECT_SET, CONFIG_SYS_MONITOR_BASE, - CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN - 1, - flash_info); -#endif - /* Env protection ON by default */ - (void)flash_protect(FLAG_PROTECT_SET, CONFIG_ENV_ADDR, - CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE - 1, - flash_info); - (void)flash_protect(FLAG_PROTECT_SET, CONFIG_ENV_ADDR_REDUND, - CONFIG_ENV_ADDR_REDUND + CONFIG_ENV_SECT_SIZE - 1, - flash_info); - - /* - * USB suff... - */ - /* - * Select the USB controller on the 440EPx ("ppc") or on the PCI bus - * ("pci") for the CompactFlash. - */ - if (usbcf != NULL && (strcmp(usbcf, "ppc") == 0)) { - /* - * If environment variable "usbcf" is defined and set to "ppc", - * then connect the CompactFlash controller to the PowerPC USB - * port. - */ - printf("Attaching CompactFlash controller to PPC USB\n"); - out_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x02, - in_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x02) | 0x10); - } else { - if (usbcf != NULL && (strcmp(usbcf, "pci") != 0)) - printf("Warning: \"korat_usbcf\" is not set to a legal " - "value (\"ppc\" or \"pci\")\n"); - - printf("Attaching CompactFlash controller to PCI USB\n"); - } - if (act == NULL || strcmp(act, "hostdev") == 0) { - /* SDR Setting */ - mfsdr(SDR0_PFC1, sdr0_pfc1); - mfsdr(SDR0_USB2D0CR, usb2d0cr); - mfsdr(SDR0_USB2PHY0CR, usb2phy0cr); - mfsdr(SDR0_USB2H0CR, usb2h0cr); - - usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL; - usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ; - usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS; - usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST; - usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST; - - /* - * An 8-bit/60MHz interface is the only possible alternative - * when connecting the Device to the PHY - */ - usb2h0cr = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK; - usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ; - - /* - * To enable the USB 2.0 Device function - * through the UTMI interface - */ - usb2d0cr = usb2d0cr &~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK; - usb2d0cr = usb2d0cr | SDR0_USB2D0CR_USB2DEV_SELECTION; - - sdr0_pfc1 = sdr0_pfc1 &~SDR0_PFC1_UES_MASK; - sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_USB2D_SEL; - - mtsdr(SDR0_PFC1, sdr0_pfc1); - mtsdr(SDR0_USB2D0CR, usb2d0cr); - mtsdr(SDR0_USB2PHY0CR, usb2phy0cr); - mtsdr(SDR0_USB2H0CR, usb2h0cr); - - /* clear resets */ - udelay(1000); - mtsdr(SDR0_SRST1, 0x00000000); - udelay(1000); - mtsdr(SDR0_SRST0, 0x00000000); - - printf("USB: Host(int phy) Device(ext phy)\n"); - - } else if (strcmp(act, "dev") == 0) { - /*-------------------PATCH-------------------------------*/ - mfsdr(SDR0_USB2PHY0CR, usb2phy0cr); - - usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL; - usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS; - usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST; - usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST; - mtsdr(SDR0_USB2PHY0CR, usb2phy0cr); - - udelay(1000); - mtsdr(SDR0_SRST1, 0x672c6000); - - udelay(1000); - mtsdr(SDR0_SRST0, 0x00000080); - - udelay(1000); - mtsdr(SDR0_SRST1, 0x60206000); - - *(unsigned int *)(0xe0000350) = 0x00000001; - - udelay(1000); - mtsdr(SDR0_SRST1, 0x60306000); - /*-------------------PATCH-------------------------------*/ - - /* SDR Setting */ - mfsdr(SDR0_USB2PHY0CR, usb2phy0cr); - mfsdr(SDR0_USB2H0CR, usb2h0cr); - mfsdr(SDR0_USB2D0CR, usb2d0cr); - mfsdr(SDR0_PFC1, sdr0_pfc1); - - usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL; - usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_8BIT_60MHZ; - usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PUREN; - usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_DEV; - usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_DEV; - - usb2h0cr = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK; - usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_8BIT_60MHZ; - - usb2d0cr = usb2d0cr &~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK; - usb2d0cr = usb2d0cr | SDR0_USB2D0CR_EBC_SELECTION; - - sdr0_pfc1 = sdr0_pfc1 &~SDR0_PFC1_UES_MASK; - sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_EBCHR_SEL; - - mtsdr(SDR0_USB2H0CR, usb2h0cr); - mtsdr(SDR0_USB2PHY0CR, usb2phy0cr); - mtsdr(SDR0_USB2D0CR, usb2d0cr); - mtsdr(SDR0_PFC1, sdr0_pfc1); - - /* clear resets */ - udelay(1000); - mtsdr(SDR0_SRST1, 0x00000000); - udelay(1000); - mtsdr(SDR0_SRST0, 0x00000000); - - printf("USB: Device(int phy)\n"); - } - - mfsdr(SDR0_SRST1, reg); /* enable security/kasumi engines */ - reg &= ~(SDR0_SRST1_CRYP0 | SDR0_SRST1_KASU0); - mtsdr(SDR0_SRST1, reg); - - /* - * Clear PLB4A0_ACR[WRP] - * This fix will make the MAL burst disabling patch for the Linux - * EMAC driver obsolete. - */ - reg = mfdcr(PLB4A0_ACR) & ~PLB4Ax_ACR_WRP_MASK; - mtdcr(PLB4A0_ACR, reg); - - set_serial_number(); - set_mac_addresses(); - gpio_write_bit(CONFIG_SYS_GPIO_ATMEGA_RESET_, 1); - - return 0; -} - -int checkboard(void) -{ - char const *const s = getenv("serial#"); - u8 const rev = in_8((u8 *) CONFIG_SYS_CPLD_BASE + 0); - - printf("Board: Korat, Rev. %X", rev); - if (s) - printf(", serial# %s", s); - - printf(".\n Ethernet PHY 0: "); - if (gpio_read_out_bit(CONFIG_SYS_GPIO_PHY0_FIBER_SEL)) - printf("fiber"); - else - printf("copper"); - - printf(", PHY 1: "); - if (gpio_read_out_bit(CONFIG_SYS_GPIO_PHY1_FIBER_SEL)) - printf("fiber"); - else - printf("copper"); - - printf(".\n"); -#if defined(CONFIG_KORAT_PERMANENT) - printf(" Executing permanent copy of U-Boot.\n"); -#endif - return 0; -} - -#if defined(CONFIG_PCI) && defined(CONFIG_PCI_PNP) -/* - * Assign interrupts to PCI devices. - */ -void board_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev) -{ - pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, VECNUM_EIRQ2); -} -#endif - -/* - * pci_target_init - * - * The bootstrap configuration provides default settings for the pci - * inbound map (PIM). But the bootstrap config choices are limited and - * may not be sufficient for a given board. - */ -#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) -void pci_target_init(struct pci_controller *hose) -{ - /* First do 440EP(x) common setup */ - __pci_target_init(hose); - - /* - * Set up Configuration registers for on-board NEC uPD720101 USB - * controller. - */ - pci_write_config_dword(PCI_BDF(0x0, 0xC, 0x0), 0xE4, 0x00000020); -} -#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */ - -#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) -int ft_board_setup(void *blob, bd_t *bd) -{ - u32 val[4]; - int rc; - - ft_cpu_setup(blob, bd); - - /* Fixup NOR mapping */ - val[0] = 1; /* chip select number */ - val[1] = 0; /* always 0 */ - val[2] = gd->bd->bi_flashstart; - val[3] = gd->bd->bi_flashsize - CONFIG_SYS_FLASH0_SIZE; - rc = fdt_find_and_setprop(blob, "/plb/opb/ebc", "ranges", - val, sizeof(val), 1); - if (rc) - printf("Unable to update property NOR mapping, err=%s\n", - fdt_strerror(rc)); - - return 0; -} -#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */ diff --git a/board/korat/u-boot-F7FC.lds b/board/korat/u-boot-F7FC.lds deleted file mode 100644 index bee4d9a..0000000 --- a/board/korat/u-boot-F7FC.lds +++ /dev/null @@ -1,124 +0,0 @@ -/* - * (C) Copyright 2002 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_ARCH(powerpc) -/* Do we need any of these for elf? - __DYNAMIC = 0; */ -SECTIONS -{ - .resetvec 0xF7FBFFFC : - { - *(.resetvec) - } = 0xffff - - .bootpg 0xF7FBF000 : - { - arch/powerpc/cpu/ppc4xx/start.o (.bootpg) - } = 0xffff - - /* Read-only sections, merged into text segment: */ - . = + SIZEOF_HEADERS; - .interp : { *(.interp) } - .hash : { *(.hash) } - .dynsym : { *(.dynsym) } - .dynstr : { *(.dynstr) } - .rel.text : { *(.rel.text) } - .rela.text : { *(.rela.text) } - .rel.data : { *(.rel.data) } - .rela.data : { *(.rela.data) } - .rel.rodata : { *(.rel.rodata) } - .rela.rodata : { *(.rela.rodata) } - .rel.got : { *(.rel.got) } - .rela.got : { *(.rela.got) } - .rel.ctors : { *(.rel.ctors) } - .rela.ctors : { *(.rela.ctors) } - .rel.dtors : { *(.rel.dtors) } - .rela.dtors : { *(.rela.dtors) } - .rel.bss : { *(.rel.bss) } - .rela.bss : { *(.rela.bss) } - .rel.plt : { *(.rel.plt) } - .rela.plt : { *(.rela.plt) } - .init : { *(.init) } - .plt : { *(.plt) } - .text : - { - /* WARNING - the following is hand-optimized to fit within */ - /* the sector layout of our flash chips! XXX FIXME XXX */ - - arch/powerpc/cpu/ppc4xx/start.o (.text) - - *(.text) - *(.got1) - } - _etext = .; - PROVIDE (etext = .); - .rodata : - { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - } - .fini : { *(.fini) } =0 - .ctors : { *(.ctors) } - .dtors : { *(.dtors) } - - /* Read-write section, merged into data segment: */ - . = (. + 0x00FF) & 0xFFFFFF00; - _erotext = .; - PROVIDE (erotext = .); - .reloc : - { - *(.got) - _GOT2_TABLE_ = .; - *(.got2) - _FIXUP_TABLE_ = .; - *(.fixup) - } - __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; - __fixup_entries = (. - _FIXUP_TABLE_)>>2; - - .data : - { - *(.data) - *(.data1) - *(.sdata) - *(.sdata2) - *(.dynamic) - CONSTRUCTORS - } - _edata = .; - PROVIDE (edata = .); - - . = .; - - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } - - . = .; - __start___ex_table = .; - __ex_table : { *(__ex_table) } - __stop___ex_table = .; - - . = ALIGN(256); - __init_begin = .; - .text.init : { *(.text.init) } - .data.init : { *(.data.init) } - . = ALIGN(256); - __init_end = .; - - __bss_start = .; - .bss (NOLOAD) : - { - *(.sbss) *(.scommon) - *(.dynbss) - *(.bss) - *(COMMON) - . = ALIGN(4); - } - - __bss_end = . ; - PROVIDE (end = .); -} |