summaryrefslogtreecommitdiff
path: root/board
diff options
context:
space:
mode:
Diffstat (limited to 'board')
-rw-r--r--board/LaCie/common/cpld-gpio-bus.c50
-rw-r--r--board/LaCie/common/cpld-gpio-bus.h24
-rw-r--r--board/LaCie/net2big_v2/Makefile3
-rw-r--r--board/LaCie/net2big_v2/net2big_v2.c154
-rw-r--r--board/LaCie/net2big_v2/net2big_v2.h5
-rw-r--r--board/actux1/u-boot.lds20
-rw-r--r--board/actux2/u-boot.lds20
-rw-r--r--board/actux3/u-boot.lds20
-rw-r--r--board/ait/cam_enc_4xx/u-boot-spl.lds5
-rw-r--r--board/davinci/da8xxevm/u-boot-spl-da850evm.lds5
-rw-r--r--board/davinci/da8xxevm/u-boot-spl-hawk.lds1
-rw-r--r--board/dvlhost/u-boot.lds20
-rw-r--r--board/freescale/mx31ads/u-boot.lds20
-rw-r--r--board/isee/igep0033/board.c40
-rw-r--r--board/phytec/pcm051/board.c39
-rw-r--r--board/samsung/dts/exynos5250-smdk5250.dts24
-rw-r--r--board/samsung/origen/lowlevel_init.S44
-rw-r--r--board/samsung/origen/origen_setup.h25
-rw-r--r--board/samsung/smdk5250/Makefile5
-rw-r--r--board/samsung/smdk5250/clock_init.c18
-rw-r--r--board/samsung/smdk5250/clock_init.h5
-rw-r--r--board/samsung/smdk5250/exynos5-dt.c423
-rw-r--r--board/samsung/smdk5250/lowlevel_init.S2
-rw-r--r--board/samsung/smdk5250/setup.h25
-rw-r--r--board/samsung/smdk5250/smdk5250.c223
-rw-r--r--board/samsung/smdk5250/spl_boot.c64
-rw-r--r--board/samsung/smdk5250/tzpc_init.c48
-rw-r--r--board/samsung/smdkv310/lowlevel_init.S60
-rw-r--r--board/ti/am335x/board.c39
-rw-r--r--board/ti/panda/panda.c104
-rw-r--r--board/ti/ti814x/evm.c35
-rw-r--r--board/vpac270/u-boot-spl.lds6
32 files changed, 976 insertions, 600 deletions
diff --git a/board/LaCie/common/cpld-gpio-bus.c b/board/LaCie/common/cpld-gpio-bus.c
new file mode 100644
index 0000000..fb9bf8d
--- /dev/null
+++ b/board/LaCie/common/cpld-gpio-bus.c
@@ -0,0 +1,50 @@
+/*
+ * cpld-gpio-bus.c: provides support for the CPLD GPIO bus found on some LaCie
+ * boards (as the 2Big/5Big Network v2 and the 2Big NAS). This parallel GPIO
+ * bus exposes two registers (address and data). Each of this register is made
+ * up of several dedicated GPIOs. An extra GPIO is used to notify the CPLD that
+ * the registers have been updated.
+ *
+ * Mostly this bus is used to configure the LEDs on LaCie boards.
+ *
+ * Copyright (C) 2013 Simon Guinot <simon.guinot@sequanux.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <asm/arch/gpio.h>
+#include "cpld-gpio-bus.h"
+
+static void cpld_gpio_bus_set_addr(struct cpld_gpio_bus *bus, unsigned addr)
+{
+ int pin;
+
+ for (pin = 0; pin < bus->num_addr; pin++)
+ kw_gpio_set_value(bus->addr[pin], (addr >> pin) & 1);
+}
+
+static void cpld_gpio_bus_set_data(struct cpld_gpio_bus *bus, unsigned data)
+{
+ int pin;
+
+ for (pin = 0; pin < bus->num_data; pin++)
+ kw_gpio_set_value(bus->data[pin], (data >> pin) & 1);
+}
+
+static void cpld_gpio_bus_enable_select(struct cpld_gpio_bus *bus)
+{
+ /* The transfer is enabled on the raising edge. */
+ kw_gpio_set_value(bus->enable, 0);
+ kw_gpio_set_value(bus->enable, 1);
+}
+
+void cpld_gpio_bus_write(struct cpld_gpio_bus *bus,
+ unsigned addr, unsigned value)
+{
+ cpld_gpio_bus_set_addr(bus, addr);
+ cpld_gpio_bus_set_data(bus, value);
+ cpld_gpio_bus_enable_select(bus);
+}
diff --git a/board/LaCie/common/cpld-gpio-bus.h b/board/LaCie/common/cpld-gpio-bus.h
new file mode 100644
index 0000000..e9e9b96
--- /dev/null
+++ b/board/LaCie/common/cpld-gpio-bus.h
@@ -0,0 +1,24 @@
+/*
+ * Copyright (C) 2013 Simon Guinot <simon.guinot@sequanux.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#ifndef _LACIE_CPLD_GPI0_BUS_H
+#define _LACIE_CPLD_GPI0_BUS_H
+
+struct cpld_gpio_bus {
+ unsigned *addr;
+ unsigned num_addr;
+ unsigned *data;
+ unsigned num_data;
+ unsigned enable;
+};
+
+void cpld_gpio_bus_write(struct cpld_gpio_bus *cpld_gpio_bus,
+ unsigned addr, unsigned value);
+
+#endif /* _LACIE_CPLD_GPI0_BUS_H */
diff --git a/board/LaCie/net2big_v2/Makefile b/board/LaCie/net2big_v2/Makefile
index fbae48e..9a6dfb6 100644
--- a/board/LaCie/net2big_v2/Makefile
+++ b/board/LaCie/net2big_v2/Makefile
@@ -28,6 +28,9 @@ endif
LIB = $(obj)lib$(BOARD).o
COBJS := $(BOARD).o ../common/common.o
+ifneq ($(and $(CONFIG_KIRKWOOD_GPIO),$(CONFIG_NET2BIG_V2)),)
+COBJS += ../common/cpld-gpio-bus.o
+endif
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
diff --git a/board/LaCie/net2big_v2/net2big_v2.c b/board/LaCie/net2big_v2/net2big_v2.c
index e524f35..b133f7c 100644
--- a/board/LaCie/net2big_v2/net2big_v2.c
+++ b/board/LaCie/net2big_v2/net2big_v2.c
@@ -22,6 +22,7 @@
#include <common.h>
#include <command.h>
+#include <i2c.h>
#include <asm/arch/cpu.h>
#include <asm/arch/kirkwood.h>
#include <asm/arch/mpp.h>
@@ -29,6 +30,7 @@
#include "net2big_v2.h"
#include "../common/common.h"
+#include "../common/cpld-gpio-bus.h"
DECLARE_GLOBAL_DATA_PTR;
@@ -60,18 +62,18 @@ int board_early_init_f(void)
MPP24_GPIO, /* USB mode select */
MPP26_GPIO, /* USB device vbus */
MPP28_GPIO, /* USB enable host vbus */
- MPP29_GPIO, /* GPIO extension ALE */
+ MPP29_GPIO, /* CPLD GPIO bus ALE */
MPP34_GPIO, /* Rear Push button 0=on 1=off */
MPP35_GPIO, /* Inhibit switch power-off */
MPP36_GPIO, /* SATA HDD1 presence */
MPP37_GPIO, /* SATA HDD2 presence */
MPP40_GPIO, /* eSATA presence */
- MPP44_GPIO, /* GPIO extension (data 0) */
- MPP45_GPIO, /* GPIO extension (data 1) */
- MPP46_GPIO, /* GPIO extension (data 2) */
- MPP47_GPIO, /* GPIO extension (addr 0) */
- MPP48_GPIO, /* GPIO extension (addr 1) */
- MPP49_GPIO, /* GPIO extension (addr 2) */
+ MPP44_GPIO, /* CPLD GPIO bus (data 0) */
+ MPP45_GPIO, /* CPLD GPIO bus (data 1) */
+ MPP46_GPIO, /* CPLD GPIO bus (data 2) */
+ MPP47_GPIO, /* CPLD GPIO bus (addr 0) */
+ MPP48_GPIO, /* CPLD GPIO bus (addr 1) */
+ MPP49_GPIO, /* CPLD GPIO bus (addr 2) */
0
};
@@ -92,8 +94,142 @@ int board_init(void)
}
#if defined(CONFIG_MISC_INIT_R)
+
+#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_G762_ADDR)
+/*
+ * Start I2C fan (GMT G762 controller)
+ */
+static void init_fan(void)
+{
+ u8 data;
+
+ i2c_set_bus_num(0);
+
+ /* Enable open-loop and PWM modes */
+ data = 0x20;
+ if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
+ G762_REG_FAN_CMD1, 1, &data, 1) != 0)
+ goto err;
+ data = 0;
+ if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
+ G762_REG_SET_CNT, 1, &data, 1) != 0)
+ goto err;
+ /*
+ * RPM to PWM (set_out register) fan speed conversion array:
+ * 0 0x00
+ * 1500 0x04
+ * 2800 0x08
+ * 3400 0x0C
+ * 3700 0x10
+ * 4400 0x20
+ * 4700 0x30
+ * 4800 0x50
+ * 5200 0x80
+ * 5400 0xC0
+ * 5500 0xFF
+ *
+ * Start fan at low speed (2800 RPM):
+ */
+ data = 0x08;
+ if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
+ G762_REG_SET_OUT, 1, &data, 1) != 0)
+ goto err;
+
+ return;
+err:
+ printf("Error: failed to start I2C fan @%02x\n",
+ CONFIG_SYS_I2C_G762_ADDR);
+}
+#else
+static void init_fan(void) {}
+#endif /* CONFIG_CMD_I2C && CONFIG_SYS_I2C_G762_ADDR */
+
+#if defined(CONFIG_NET2BIG_V2) && defined(CONFIG_KIRKWOOD_GPIO)
+/*
+ * CPLD GPIO bus:
+ *
+ * - address register : bit [0-2] -> GPIO [47-49]
+ * - data register : bit [0-2] -> GPIO [44-46]
+ * - enable register : GPIO 29
+ */
+static unsigned cpld_gpio_bus_addr[] = { 47, 48, 49 };
+static unsigned cpld_gpio_bus_data[] = { 44, 45, 46 };
+
+static struct cpld_gpio_bus cpld_gpio_bus = {
+ .addr = cpld_gpio_bus_addr,
+ .num_addr = ARRAY_SIZE(cpld_gpio_bus_addr),
+ .data = cpld_gpio_bus_data,
+ .num_data = ARRAY_SIZE(cpld_gpio_bus_data),
+ .enable = 29,
+};
+
+/*
+ * LEDs configuration:
+ *
+ * The LEDs are controlled by a CPLD and can be configured through
+ * the CPLD GPIO bus.
+ *
+ * Address register selection:
+ *
+ * addr | register
+ * ----------------------------
+ * 0 | front LED
+ * 1 | front LED brightness
+ * 2 | SATA LED brightness
+ * 3 | SATA0 LED
+ * 4 | SATA1 LED
+ * 5 | SATA2 LED
+ * 6 | SATA3 LED
+ * 7 | SATA4 LED
+ *
+ * Data register configuration:
+ *
+ * data | LED brightness
+ * -------------------------------------------------
+ * 0 | min (off)
+ * - | -
+ * 7 | max
+ *
+ * data | front LED mode
+ * -------------------------------------------------
+ * 0 | fix off
+ * 1 | fix blue on
+ * 2 | fix red on
+ * 3 | blink blue on=1 sec and blue off=1 sec
+ * 4 | blink red on=1 sec and red off=1 sec
+ * 5 | blink blue on=2.5 sec and red on=0.5 sec
+ * 6 | blink blue on=1 sec and red on=1 sec
+ * 7 | blink blue on=0.5 sec and blue off=2.5 sec
+ *
+ * data | SATA LED mode
+ * -------------------------------------------------
+ * 0 | fix off
+ * 1 | SATA activity blink
+ * 2 | fix red on
+ * 3 | blink blue on=1 sec and blue off=1 sec
+ * 4 | blink red on=1 sec and red off=1 sec
+ * 5 | blink blue on=2.5 sec and red on=0.5 sec
+ * 6 | blink blue on=1 sec and red on=1 sec
+ * 7 | fix blue on
+ */
+static void init_leds(void)
+{
+ /* Enable the front blue LED */
+ cpld_gpio_bus_write(&cpld_gpio_bus, 0, 1);
+ cpld_gpio_bus_write(&cpld_gpio_bus, 1, 3);
+
+ /* Configure SATA LEDs to blink in relation with the SATA activity */
+ cpld_gpio_bus_write(&cpld_gpio_bus, 3, 1);
+ cpld_gpio_bus_write(&cpld_gpio_bus, 4, 1);
+ cpld_gpio_bus_write(&cpld_gpio_bus, 2, 3);
+}
+#else
+static void init_leds(void) {}
+#endif /* CONFIG_NET2BIG_V2 && CONFIG_KIRKWOOD_GPIO */
+
int misc_init_r(void)
{
+ init_fan();
#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
if (!getenv("ethaddr")) {
uchar mac[6];
@@ -101,9 +237,11 @@ int misc_init_r(void)
eth_setenv_enetaddr("ethaddr", mac);
}
#endif
+ init_leds();
+
return 0;
}
-#endif
+#endif /* CONFIG_MISC_INIT_R */
#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
/* Configure and initialize PHY */
diff --git a/board/LaCie/net2big_v2/net2big_v2.h b/board/LaCie/net2big_v2/net2big_v2.h
index f9778f4..83537d6 100644
--- a/board/LaCie/net2big_v2/net2big_v2.h
+++ b/board/LaCie/net2big_v2/net2big_v2.h
@@ -32,4 +32,9 @@
/* Buttons */
#define NET2BIG_V2_GPIO_PUSH_BUTTON 34
+/* GMT G762 registers (I2C fan controller) */
+#define G762_REG_SET_CNT 0x00
+#define G762_REG_SET_OUT 0x03
+#define G762_REG_FAN_CMD1 0x04
+
#endif /* NET2BIG_V2_H */
diff --git a/board/actux1/u-boot.lds b/board/actux1/u-boot.lds
index ef4a25b..74aec5f 100644
--- a/board/actux1/u-boot.lds
+++ b/board/actux1/u-boot.lds
@@ -30,6 +30,7 @@ SECTIONS
. = ALIGN (4);
.text : {
+ *(.__image_copy_start)
arch/arm/cpu/ixp/start.o(.text*)
net/libnet.o(.text*)
board/actux1/libactux1.o(.text*)
@@ -62,17 +63,23 @@ SECTIONS
. = ALIGN (4);
- __image_copy_end = .;
+ .image_copy_end :
+ {
+ *(.__image_copy_end)
+ }
+
+ .rel_dyn_start :
+ {
+ *(.__rel_dyn_start)
+ }
.rel.dyn : {
- __rel_dyn_start = .;
*(.rel*)
- __rel_dyn_end = .;
}
- .dynsym : {
- __dynsym_start = .;
- *(.dynsym)
+ .rel_dyn_end :
+ {
+ *(.__rel_dyn_end)
}
_end = .;
@@ -96,6 +103,7 @@ SECTIONS
KEEP(*(.__bss_end));
}
+ /DISCARD/ : { *(.dynsym) }
/DISCARD/ : { *(.dynstr*) }
/DISCARD/ : { *(.dynamic*) }
/DISCARD/ : { *(.plt*) }
diff --git a/board/actux2/u-boot.lds b/board/actux2/u-boot.lds
index 00ad8b7..c276501 100644
--- a/board/actux2/u-boot.lds
+++ b/board/actux2/u-boot.lds
@@ -30,6 +30,7 @@ SECTIONS
. = ALIGN (4);
.text : {
+ *(.__image_copy_start)
arch/arm/cpu/ixp/start.o(.text*)
net/libnet.o(.text*)
board/actux2/libactux2.o(.text*)
@@ -62,17 +63,23 @@ SECTIONS
. = ALIGN (4);
- __image_copy_end = .;
+ .image_copy_end :
+ {
+ *(.__image_copy_end)
+ }
+
+ .rel_dyn_start :
+ {
+ *(.__rel_dyn_start)
+ }
.rel.dyn : {
- __rel_dyn_start = .;
*(.rel*)
- __rel_dyn_end = .;
}
- .dynsym : {
- __dynsym_start = .;
- *(.dynsym)
+ .rel_dyn_end :
+ {
+ *(.__rel_dyn_end)
}
_end = .;
@@ -96,6 +103,7 @@ SECTIONS
KEEP(*(.__bss_end));
}
+ /DISCARD/ : { *(.dynsym) }
/DISCARD/ : { *(.dynstr*) }
/DISCARD/ : { *(.dynamic*) }
/DISCARD/ : { *(.plt*) }
diff --git a/board/actux3/u-boot.lds b/board/actux3/u-boot.lds
index 44b990e..5610644 100644
--- a/board/actux3/u-boot.lds
+++ b/board/actux3/u-boot.lds
@@ -30,6 +30,7 @@ SECTIONS
. = ALIGN (4);
.text : {
+ *(.__image_copy_start)
arch/arm/cpu/ixp/start.o(.text*)
net/libnet.o(.text*)
board/actux3/libactux3.o(.text*)
@@ -62,17 +63,23 @@ SECTIONS
. = ALIGN (4);
- __image_copy_end = .;
+ .image_copy_end :
+ {
+ *(.__image_copy_end)
+ }
+
+ .rel_dyn_start :
+ {
+ *(.__rel_dyn_start)
+ }
.rel.dyn : {
- __rel_dyn_start = .;
*(.rel*)
- __rel_dyn_end = .;
}
- .dynsym : {
- __dynsym_start = .;
- *(.dynsym)
+ .rel_dyn_end :
+ {
+ *(.__rel_dyn_end)
}
_end = .;
@@ -96,6 +103,7 @@ SECTIONS
KEEP(*(.__bss_end));
}
+ /DISCARD/ : { *(.dynsym) }
/DISCARD/ : { *(.dynstr*) }
/DISCARD/ : { *(.dynamic*) }
/DISCARD/ : { *(.plt*) }
diff --git a/board/ait/cam_enc_4xx/u-boot-spl.lds b/board/ait/cam_enc_4xx/u-boot-spl.lds
index 1daa1b3..3972685 100644
--- a/board/ait/cam_enc_4xx/u-boot-spl.lds
+++ b/board/ait/cam_enc_4xx/u-boot-spl.lds
@@ -54,11 +54,6 @@ SECTIONS
__rel_dyn_end = .;
} >.sram
- .dynsym : {
- __dynsym_start = .;
- *(.dynsym)
- } >.sram
-
.bss :
{
. = ALIGN(4);
diff --git a/board/davinci/da8xxevm/u-boot-spl-da850evm.lds b/board/davinci/da8xxevm/u-boot-spl-da850evm.lds
index b1b8701..6fa4509 100644
--- a/board/davinci/da8xxevm/u-boot-spl-da850evm.lds
+++ b/board/davinci/da8xxevm/u-boot-spl-da850evm.lds
@@ -55,11 +55,6 @@ SECTIONS
__rel_dyn_end = .;
} >.sram
- .dynsym : {
- __dynsym_start = .;
- *(.dynsym)
- } >.sram
-
.bss :
{
. = ALIGN(4);
diff --git a/board/davinci/da8xxevm/u-boot-spl-hawk.lds b/board/davinci/da8xxevm/u-boot-spl-hawk.lds
index 596a9e0..b452f20 100644
--- a/board/davinci/da8xxevm/u-boot-spl-hawk.lds
+++ b/board/davinci/da8xxevm/u-boot-spl-hawk.lds
@@ -61,7 +61,6 @@ SECTIONS
__image_copy_end = .;
__rel_dyn_start = .;
__rel_dyn_end = .;
- __dynsym_start = .;
__got_start = .;
. = ALIGN(4);
diff --git a/board/dvlhost/u-boot.lds b/board/dvlhost/u-boot.lds
index 6d4b187..f359112 100644
--- a/board/dvlhost/u-boot.lds
+++ b/board/dvlhost/u-boot.lds
@@ -30,6 +30,7 @@ SECTIONS
. = ALIGN (4);
.text : {
+ *(.__image_copy_start)
arch/arm/cpu/ixp/start.o(.text*)
net/libnet.o(.text*)
board/dvlhost/libdvlhost.o(.text*)
@@ -62,17 +63,23 @@ SECTIONS
. = ALIGN (4);
- __image_copy_end = .;
+ .image_copy_end :
+ {
+ *(.__image_copy_end)
+ }
+
+ .rel_dyn_start :
+ {
+ *(.__rel_dyn_start)
+ }
.rel.dyn : {
- __rel_dyn_start = .;
*(.rel*)
- __rel_dyn_end = .;
}
- .dynsym : {
- __dynsym_start = .;
- *(.dynsym)
+ .rel_dyn_end :
+ {
+ *(.__rel_dyn_end)
}
_end = .;
@@ -96,6 +103,7 @@ SECTIONS
KEEP(*(.__bss_end));
}
+ /DISCARD/ : { *(.dynsym) }
/DISCARD/ : { *(.dynstr*) }
/DISCARD/ : { *(.dynamic*) }
/DISCARD/ : { *(.plt*) }
diff --git a/board/freescale/mx31ads/u-boot.lds b/board/freescale/mx31ads/u-boot.lds
index 4969960..963d29f 100644
--- a/board/freescale/mx31ads/u-boot.lds
+++ b/board/freescale/mx31ads/u-boot.lds
@@ -34,6 +34,7 @@ SECTIONS
. = ALIGN(4);
.text :
{
+ *(.__image_copy_start)
/* WARNING - the following is hand-optimized to fit within */
/* the sector layout of our flash chips! XXX FIXME XXX */
@@ -65,17 +66,23 @@ SECTIONS
. = ALIGN(4);
- __image_copy_end = .;
+ .image_copy_end :
+ {
+ *(.__image_copy_end)
+ }
+
+ .rel_dyn_start :
+ {
+ *(.__rel_dyn_start)
+ }
.rel.dyn : {
- __rel_dyn_start = .;
*(.rel*)
- __rel_dyn_end = .;
}
- .dynsym : {
- __dynsym_start = .;
- *(.dynsym)
+ .rel_dyn_end :
+ {
+ *(.__rel_dyn_end)
}
_end = .;
@@ -100,6 +107,7 @@ SECTIONS
}
/DISCARD/ : { *(.bss*) }
+ /DISCARD/ : { *(.dynsym) }
/DISCARD/ : { *(.dynstr*) }
/DISCARD/ : { *(.dynsym*) }
/DISCARD/ : { *(.dynamic*) }
diff --git a/board/isee/igep0033/board.c b/board/isee/igep0033/board.c
index 826cead..ea3bea5 100644
--- a/board/isee/igep0033/board.c
+++ b/board/isee/igep0033/board.c
@@ -36,37 +36,13 @@
DECLARE_GLOBAL_DATA_PTR;
static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
-#ifdef CONFIG_SPL_BUILD
-static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE;
-#endif
/* MII mode defines */
#define RMII_MODE_ENABLE 0x4D
static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
-/* UART Defines */
#ifdef CONFIG_SPL_BUILD
-#define UART_RESET (0x1 << 1)
-#define UART_CLK_RUNNING_MASK 0x1
-#define UART_SMART_IDLE_EN (0x1 << 0x3)
-
-static void rtc32k_enable(void)
-{
- struct rtc_regs *rtc = (struct rtc_regs *)RTC_BASE;
-
- /*
- * Unlock the RTC's registers. For more details please see the
- * RTC_SS section of the TRM. In order to unlock we need to
- * write these specific values (keys) in this order.
- */
- writel(0x83e70b13, &rtc->kick0r);
- writel(0x95a4f1e0, &rtc->kick1r);
-
- /* Enable the RTC 32K OSC by setting bits 3 and 6. */
- writel((1 << 3) | (1 << 6), &rtc->osc);
-}
-
static const struct ddr_data ddr3_data = {
.datardsratio0 = K4B2G1646EBIH9_RD_DQS,
.datawdsratio0 = K4B2G1646EBIH9_WR_DQS,
@@ -131,23 +107,9 @@ void s_init(void)
/* Enable RTC32K clock */
rtc32k_enable();
- /* UART softreset */
- u32 regval;
-
enable_uart0_pin_mux();
- regval = readl(&uart_base->uartsyscfg);
- regval |= UART_RESET;
- writel(regval, &uart_base->uartsyscfg);
- while ((readl(&uart_base->uartsyssts) &
- UART_CLK_RUNNING_MASK) != UART_CLK_RUNNING_MASK)
- ;
-
- /* Disable smart idle */
- regval = readl(&uart_base->uartsyscfg);
- regval |= UART_SMART_IDLE_EN;
- writel(regval, &uart_base->uartsyscfg);
-
+ uart_soft_reset();
gd = &gdata;
preloader_console_init();
diff --git a/board/phytec/pcm051/board.c b/board/phytec/pcm051/board.c
index 93c611d..0cca8d7 100644
--- a/board/phytec/pcm051/board.c
+++ b/board/phytec/pcm051/board.c
@@ -39,9 +39,6 @@
DECLARE_GLOBAL_DATA_PTR;
static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
-#ifdef CONFIG_SPL_BUILD
-static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE;
-#endif
/* MII mode defines */
#define MII_MODE_ENABLE 0x0
@@ -50,31 +47,11 @@ static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE;
static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
-/* UART defines */
#ifdef CONFIG_SPL_BUILD
-#define UART_RESET (0x1 << 1)
-#define UART_CLK_RUNNING_MASK 0x1
-#define UART_SMART_IDLE_EN (0x1 << 0x3)
/* DDR RAM defines */
#define DDR_CLK_MHZ 303 /* DDR_DPLL_MULT value */
-static void rtc32k_enable(void)
-{
- struct rtc_regs *rtc = (struct rtc_regs *)RTC_BASE;
-
- /*
- * Unlock the RTC's registers. For more details please see the
- * RTC_SS section of the TRM. In order to unlock we need to
- * write these specific values (keys) in this order.
- */
- writel(0x83e70b13, &rtc->kick0r);
- writel(0x95a4f1e0, &rtc->kick1r);
-
- /* Enable the RTC 32K OSC by setting bits 3 and 6. */
- writel((1 << 3) | (1 << 6), &rtc->osc);
-}
-
static const struct ddr_data ddr3_data = {
.datardsratio0 = MT41J256M8HX15E_RD_DQS,
.datawdsratio0 = MT41J256M8HX15E_WR_DQS,
@@ -141,22 +118,8 @@ void s_init(void)
/* Enable RTC32K clock */
rtc32k_enable();
- /* UART softreset */
- u32 regval;
-
enable_uart0_pin_mux();
-
- regval = readl(&uart_base->uartsyscfg);
- regval |= UART_RESET;
- writel(regval, &uart_base->uartsyscfg);
- while ((readl(&uart_base->uartsyssts) & UART_CLK_RUNNING_MASK)
- != UART_CLK_RUNNING_MASK)
- ;
-
- /* Disable smart idle */
- regval = readl(&uart_base->uartsyscfg);
- regval |= UART_SMART_IDLE_EN;
- writel(regval, &uart_base->uartsyscfg);
+ uart_soft_reset();
gd = &gdata;
diff --git a/board/samsung/dts/exynos5250-smdk5250.dts b/board/samsung/dts/exynos5250-smdk5250.dts
index 8da973b..93375a6 100644
--- a/board/samsung/dts/exynos5250-smdk5250.dts
+++ b/board/samsung/dts/exynos5250-smdk5250.dts
@@ -30,6 +30,10 @@
spi2 = "/spi@12d40000";
spi3 = "/spi@131a0000";
spi4 = "/spi@131b0000";
+ mmc0 = "/mmc@12200000";
+ mmc1 = "/mmc@12210000";
+ mmc2 = "/mmc@12220000";
+ mmc3 = "/mmc@12230000";
};
sromc@12250000 {
@@ -119,4 +123,24 @@
samsung,ycbcr-coeff = <0>;
samsung,color-depth = <1>;
};
+
+ mmc@12200000 {
+ samsung,bus-width = <8>;
+ samsung,timing = <1 3 3>;
+ samsung,removable = <0>;
+ };
+
+ mmc@12210000 {
+ status = "disabled";
+ };
+
+ mmc@12220000 {
+ samsung,bus-width = <4>;
+ samsung,timing = <1 2 3>;
+ samsung,removable = <1>;
+ };
+
+ mmc@12230000 {
+ status = "disabled";
+ };
};
diff --git a/board/samsung/origen/lowlevel_init.S b/board/samsung/origen/lowlevel_init.S
index 9daa0da..be9d418 100644
--- a/board/samsung/origen/lowlevel_init.S
+++ b/board/samsung/origen/lowlevel_init.S
@@ -87,12 +87,14 @@ lowlevel_init:
1:
/* for UART */
bl uart_asm_init
+ bl arch_cpu_init
bl tzpc_init
pop {pc}
wakeup_reset:
bl system_clock_init
bl mem_ctrl_asm_init
+ bl arch_cpu_init
bl tzpc_init
exit_wakeup:
@@ -353,45 +355,3 @@ uart_asm_init:
nop
nop
-/* Setting TZPC[TrustZone Protection Controller] */
-tzpc_init:
- ldr r0, =TZPC0_BASE
- mov r1, #R0SIZE
- str r1, [r0]
- mov r1, #DECPROTXSET
- str r1, [r0, #TZPC_DECPROT0SET_OFFSET]
- str r1, [r0, #TZPC_DECPROT1SET_OFFSET]
- str r1, [r0, #TZPC_DECPROT2SET_OFFSET]
- str r1, [r0, #TZPC_DECPROT3SET_OFFSET]
-
- ldr r0, =TZPC1_BASE
- str r1, [r0, #TZPC_DECPROT0SET_OFFSET]
- str r1, [r0, #TZPC_DECPROT1SET_OFFSET]
- str r1, [r0, #TZPC_DECPROT2SET_OFFSET]
- str r1, [r0, #TZPC_DECPROT3SET_OFFSET]
-
- ldr r0, =TZPC2_BASE
- str r1, [r0, #TZPC_DECPROT0SET_OFFSET]
- str r1, [r0, #TZPC_DECPROT1SET_OFFSET]
- str r1, [r0, #TZPC_DECPROT2SET_OFFSET]
- str r1, [r0, #TZPC_DECPROT3SET_OFFSET]
-
- ldr r0, =TZPC3_BASE
- str r1, [r0, #TZPC_DECPROT0SET_OFFSET]
- str r1, [r0, #TZPC_DECPROT1SET_OFFSET]
- str r1, [r0, #TZPC_DECPROT2SET_OFFSET]
- str r1, [r0, #TZPC_DECPROT3SET_OFFSET]
-
- ldr r0, =TZPC4_BASE
- str r1, [r0, #TZPC_DECPROT0SET_OFFSET]
- str r1, [r0, #TZPC_DECPROT1SET_OFFSET]
- str r1, [r0, #TZPC_DECPROT2SET_OFFSET]
- str r1, [r0, #TZPC_DECPROT3SET_OFFSET]
-
- ldr r0, =TZPC5_BASE
- str r1, [r0, #TZPC_DECPROT0SET_OFFSET]
- str r1, [r0, #TZPC_DECPROT1SET_OFFSET]
- str r1, [r0, #TZPC_DECPROT2SET_OFFSET]
- str r1, [r0, #TZPC_DECPROT3SET_OFFSET]
-
- mov pc, lr
diff --git a/board/samsung/origen/origen_setup.h b/board/samsung/origen/origen_setup.h
index 930b948..926a4cc 100644
--- a/board/samsung/origen/origen_setup.h
+++ b/board/samsung/origen/origen_setup.h
@@ -121,19 +121,6 @@
#define UBRDIV_OFFSET 0x28
#define UFRACVAL_OFFSET 0x2C
-/* TZPC : Register Offsets */
-#define TZPC0_BASE 0x10110000
-#define TZPC1_BASE 0x10120000
-#define TZPC2_BASE 0x10130000
-#define TZPC3_BASE 0x10140000
-#define TZPC4_BASE 0x10150000
-#define TZPC5_BASE 0x10160000
-
-#define TZPC_DECPROT0SET_OFFSET 0x804
-#define TZPC_DECPROT1SET_OFFSET 0x810
-#define TZPC_DECPROT2SET_OFFSET 0x81C
-#define TZPC_DECPROT3SET_OFFSET 0x828
-
/* CLK_SRC_CPU */
#define MUX_HPM_SEL_MOUTAPLL 0x0
#define MUX_HPM_SEL_SCLKMPLL 0x1
@@ -617,16 +604,4 @@
* UBRFRACVAL = ((((800MHz*10/(115200*16) -10))%10)*16/10)
*/
#define UFRACVAL_VAL 0x4
-
-/*
- * TZPC Register Value :
- * R0SIZE: 0x0 : Size of secured ram
- */
-#define R0SIZE 0x0
-
-/*
- * TZPC Decode Protection Register Value :
- * DECPROTXSET: 0xFF : Set Decode region to non-secure
- */
-#define DECPROTXSET 0xFF
#endif
diff --git a/board/samsung/smdk5250/Makefile b/board/samsung/smdk5250/Makefile
index 47c6a5a..f2c32ee 100644
--- a/board/samsung/smdk5250/Makefile
+++ b/board/samsung/smdk5250/Makefile
@@ -28,12 +28,15 @@ SOBJS := lowlevel_init.o
COBJS := clock_init.o
COBJS += dmc_common.o dmc_init_ddr3.o
-COBJS += tzpc_init.o
COBJS += smdk5250_spl.o
ifndef CONFIG_SPL_BUILD
+ifdef CONFIG_OF_CONTROL
+COBJS += exynos5-dt.o
+else
COBJS += smdk5250.o
endif
+endif
ifdef CONFIG_SPL_BUILD
COBJS += spl_boot.o
diff --git a/board/samsung/smdk5250/clock_init.c b/board/samsung/smdk5250/clock_init.c
index 5b9e82f..b288e66 100644
--- a/board/samsung/smdk5250/clock_init.c
+++ b/board/samsung/smdk5250/clock_init.c
@@ -28,10 +28,14 @@
#include <asm/arch/clk.h>
#include <asm/arch/clock.h>
#include <asm/arch/spl.h>
+#include <asm/arch/dwmmc.h>
#include "clock_init.h"
#include "setup.h"
+#define FSYS1_MMC0_DIV_MASK 0xff0f
+#define FSYS1_MMC0_DIV_VAL 0x0701
+
DECLARE_GLOBAL_DATA_PTR;
struct arm_clk_ratios arm_clk_ratios[] = {
@@ -664,3 +668,17 @@ void clock_init_dp_clock(void)
/* We run DP at 267 Mhz */
setbits_le32(&clk->div_disp1_0, CLK_DIV_DISP1_0_FIMD1);
}
+
+/*
+ * Set clock divisor value for booting from EMMC.
+ * Set DWMMC channel-0 clk div to operate mmc0 device at 50MHz.
+ */
+void emmc_boot_clk_div_set(void)
+{
+ struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE;
+ unsigned int div_mmc;
+
+ div_mmc = readl((unsigned int) &clk->div_fsys1) & ~FSYS1_MMC0_DIV_MASK;
+ div_mmc |= FSYS1_MMC0_DIV_VAL;
+ writel(div_mmc, (unsigned int) &clk->div_fsys1);
+}
diff --git a/board/samsung/smdk5250/clock_init.h b/board/samsung/smdk5250/clock_init.h
index f751bcb..20a1d47 100644
--- a/board/samsung/smdk5250/clock_init.h
+++ b/board/samsung/smdk5250/clock_init.h
@@ -146,4 +146,9 @@ struct mem_timings *clock_get_mem_timings(void);
* Initialize clock for the device
*/
void system_clock_init(void);
+
+/*
+ * Set clock divisor value for booting from EMMC.
+ */
+void emmc_boot_clk_div_set(void);
#endif
diff --git a/board/samsung/smdk5250/exynos5-dt.c b/board/samsung/smdk5250/exynos5-dt.c
new file mode 100644
index 0000000..8131505
--- /dev/null
+++ b/board/samsung/smdk5250/exynos5-dt.c
@@ -0,0 +1,423 @@
+/*
+ * Copyright (C) 2012 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <fdtdec.h>
+#include <asm/io.h>
+#include <errno.h>
+#include <i2c.h>
+#include <netdev.h>
+#include <spi.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/dwmmc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/power.h>
+#include <asm/arch/sromc.h>
+#include <power/pmic.h>
+#include <power/max77686_pmic.h>
+#include <tmu.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#if defined CONFIG_EXYNOS_TMU
+/*
+ * Boot Time Thermal Analysis for SoC temperature threshold breach
+ */
+static void boot_temp_check(void)
+{
+ int temp;
+
+ switch (tmu_monitor(&temp)) {
+ /* Status TRIPPED ans WARNING means corresponding threshold breach */
+ case TMU_STATUS_TRIPPED:
+ puts("EXYNOS_TMU: TRIPPING! Device power going down ...\n");
+ set_ps_hold_ctrl();
+ hang();
+ break;
+ case TMU_STATUS_WARNING:
+ puts("EXYNOS_TMU: WARNING! Temperature very high\n");
+ break;
+ /*
+ * TMU_STATUS_INIT means something is wrong with temperature sensing
+ * and TMU status was changed back from NORMAL to INIT.
+ */
+ case TMU_STATUS_INIT:
+ default:
+ debug("EXYNOS_TMU: Unknown TMU state\n");
+ }
+}
+#endif
+
+#ifdef CONFIG_USB_EHCI_EXYNOS
+int board_usb_vbus_init(void)
+{
+ struct exynos5_gpio_part1 *gpio1 = (struct exynos5_gpio_part1 *)
+ samsung_get_base_gpio_part1();
+
+ /* Enable VBUS power switch */
+ s5p_gpio_direction_output(&gpio1->x2, 6, 1);
+
+ /* VBUS turn ON time */
+ mdelay(3);
+
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_SOUND_MAX98095
+static void board_enable_audio_codec(void)
+{
+ struct exynos5_gpio_part1 *gpio1 = (struct exynos5_gpio_part1 *)
+ samsung_get_base_gpio_part1();
+
+ /* Enable MAX98095 Codec */
+ s5p_gpio_direction_output(&gpio1->x1, 7, 1);
+ s5p_gpio_set_pull(&gpio1->x1, 7, GPIO_PULL_NONE);
+}
+#endif
+
+int board_init(void)
+{
+ gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
+
+#if defined CONFIG_EXYNOS_TMU
+ if (tmu_init(gd->fdt_blob) != TMU_STATUS_NORMAL) {
+ debug("%s: Failed to init TMU\n", __func__);
+ return -1;
+ }
+ boot_temp_check();
+#endif
+
+#ifdef CONFIG_EXYNOS_SPI
+ spi_init();
+#endif
+#ifdef CONFIG_USB_EHCI_EXYNOS
+ board_usb_vbus_init();
+#endif
+#ifdef CONFIG_SOUND_MAX98095
+ board_enable_audio_codec();
+#endif
+ return 0;
+}
+
+int dram_init(void)
+{
+ int i;
+ u32 addr;
+
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
+ gd->ram_size += get_ram_size((long *)addr, SDRAM_BANK_SIZE);
+ }
+ return 0;
+}
+
+#if defined(CONFIG_POWER)
+static int pmic_reg_update(struct pmic *p, int reg, uint regval)
+{
+ u32 val;
+ int ret = 0;
+
+ ret = pmic_reg_read(p, reg, &val);
+ if (ret) {
+ debug("%s: PMIC %d register read failed\n", __func__, reg);
+ return -1;
+ }
+ val |= regval;
+ ret = pmic_reg_write(p, reg, val);
+ if (ret) {
+ debug("%s: PMIC %d register write failed\n", __func__, reg);
+ return -1;
+ }
+ return 0;
+}
+
+int power_init_board(void)
+{
+ struct pmic *p;
+
+ set_ps_hold_ctrl();
+
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+
+ if (pmic_init(I2C_PMIC))
+ return -1;
+
+ p = pmic_get("MAX77686_PMIC");
+ if (!p)
+ return -ENODEV;
+
+ if (pmic_probe(p))
+ return -1;
+
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_32KHZ, MAX77686_32KHCP_EN))
+ return -1;
+
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_BBAT,
+ MAX77686_BBCHOSTEN | MAX77686_BBCVS_3_5V))
+ return -1;
+
+ /* VDD_MIF */
+ if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK1OUT,
+ MAX77686_BUCK1OUT_1V)) {
+ debug("%s: PMIC %d register write failed\n", __func__,
+ MAX77686_REG_PMIC_BUCK1OUT);
+ return -1;
+ }
+
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK1CRTL,
+ MAX77686_BUCK1CTRL_EN))
+ return -1;
+
+ /* VDD_ARM */
+ if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK2DVS1,
+ MAX77686_BUCK2DVS1_1_3V)) {
+ debug("%s: PMIC %d register write failed\n", __func__,
+ MAX77686_REG_PMIC_BUCK2DVS1);
+ return -1;
+ }
+
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK2CTRL1,
+ MAX77686_BUCK2CTRL_ON))
+ return -1;
+
+ /* VDD_INT */
+ if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK3DVS1,
+ MAX77686_BUCK3DVS1_1_0125V)) {
+ debug("%s: PMIC %d register write failed\n", __func__,
+ MAX77686_REG_PMIC_BUCK3DVS1);
+ return -1;
+ }
+
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK3CTRL,
+ MAX77686_BUCK3CTRL_ON))
+ return -1;
+
+ /* VDD_G3D */
+ if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK4DVS1,
+ MAX77686_BUCK4DVS1_1_2V)) {
+ debug("%s: PMIC %d register write failed\n", __func__,
+ MAX77686_REG_PMIC_BUCK4DVS1);
+ return -1;
+ }
+
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK4CTRL1,
+ MAX77686_BUCK3CTRL_ON))
+ return -1;
+
+ /* VDD_LDO2 */
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO2CTRL1,
+ MAX77686_LD02CTRL1_1_5V | EN_LDO))
+ return -1;
+
+ /* VDD_LDO3 */
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO3CTRL1,
+ MAX77686_LD03CTRL1_1_8V | EN_LDO))
+ return -1;
+
+ /* VDD_LDO5 */
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO5CTRL1,
+ MAX77686_LD05CTRL1_1_8V | EN_LDO))
+ return -1;
+
+ /* VDD_LDO10 */
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO10CTRL1,
+ MAX77686_LD10CTRL1_1_8V | EN_LDO))
+ return -1;
+
+ return 0;
+}
+#endif
+
+void dram_init_banksize(void)
+{
+ int i;
+ u32 addr, size;
+
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
+ size = get_ram_size((long *)addr, SDRAM_BANK_SIZE);
+
+ gd->bd->bi_dram[i].start = addr;
+ gd->bd->bi_dram[i].size = size;
+ }
+}
+
+static int decode_sromc(const void *blob, struct fdt_sromc *config)
+{
+ int err;
+ int node;
+
+ node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_SROMC);
+ if (node < 0) {
+ debug("Could not find SROMC node\n");
+ return node;
+ }
+
+ config->bank = fdtdec_get_int(blob, node, "bank", 0);
+ config->width = fdtdec_get_int(blob, node, "width", 2);
+
+ err = fdtdec_get_int_array(blob, node, "srom-timing", config->timing,
+ FDT_SROM_TIMING_COUNT);
+ if (err < 0) {
+ debug("Could not decode SROMC configuration Error: %s\n",
+ fdt_strerror(err));
+ return -FDT_ERR_NOTFOUND;
+ }
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+#ifdef CONFIG_SMC911X
+ u32 smc_bw_conf, smc_bc_conf;
+ struct fdt_sromc config;
+ fdt_addr_t base_addr;
+ int node;
+
+ node = decode_sromc(gd->fdt_blob, &config);
+ if (node < 0) {
+ debug("%s: Could not find sromc configuration\n", __func__);
+ return 0;
+ }
+ node = fdtdec_next_compatible(gd->fdt_blob, node, COMPAT_SMSC_LAN9215);
+ if (node < 0) {
+ debug("%s: Could not find lan9215 configuration\n", __func__);
+ return 0;
+ }
+
+ /* We now have a node, so any problems from now on are errors */
+ base_addr = fdtdec_get_addr(gd->fdt_blob, node, "reg");
+ if (base_addr == FDT_ADDR_T_NONE) {
+ debug("%s: Could not find lan9215 address\n", __func__);
+ return -1;
+ }
+
+ /* Ethernet needs data bus width of 16 bits */
+ if (config.width != 2) {
+ debug("%s: Unsupported bus width %d\n", __func__,
+ config.width);
+ return -1;
+ }
+ smc_bw_conf = SROMC_DATA16_WIDTH(config.bank)
+ | SROMC_BYTE_ENABLE(config.bank);
+
+ smc_bc_conf = SROMC_BC_TACS(config.timing[FDT_SROM_TACS]) |
+ SROMC_BC_TCOS(config.timing[FDT_SROM_TCOS]) |
+ SROMC_BC_TACC(config.timing[FDT_SROM_TACC]) |
+ SROMC_BC_TCOH(config.timing[FDT_SROM_TCOH]) |
+ SROMC_BC_TAH(config.timing[FDT_SROM_TAH]) |
+ SROMC_BC_TACP(config.timing[FDT_SROM_TACP]) |
+ SROMC_BC_PMC(config.timing[FDT_SROM_PMC]);
+
+ /* Select and configure the SROMC bank */
+ exynos_pinmux_config(PERIPH_ID_SROMC, config.bank);
+ s5p_config_sromc(config.bank, smc_bw_conf, smc_bc_conf);
+ return smc911x_initialize(0, base_addr);
+#endif
+ return 0;
+}
+
+#ifdef CONFIG_DISPLAY_BOARDINFO
+int checkboard(void)
+{
+ const char *board_name;
+
+ board_name = fdt_getprop(gd->fdt_blob, 0, "model", NULL);
+ if (board_name == NULL)
+ printf("\nUnknown Board\n");
+ else
+ printf("\nBoard: %s\n", board_name);
+
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_GENERIC_MMC
+int board_mmc_init(bd_t *bis)
+{
+ int ret;
+ /* dwmmc initializattion for available channels */
+ ret = exynos_dwmmc_init(gd->fdt_blob);
+ if (ret)
+ debug("dwmmc init failed\n");
+
+ return ret;
+}
+#endif
+
+static int board_uart_init(void)
+{
+ int err, uart_id, ret = 0;
+
+ for (uart_id = PERIPH_ID_UART0; uart_id <= PERIPH_ID_UART3; uart_id++) {
+ err = exynos_pinmux_config(uart_id, PINMUX_FLAG_NONE);
+ if (err) {
+ debug("UART%d not configured\n",
+ (uart_id - PERIPH_ID_UART0));
+ ret |= err;
+ }
+ }
+ return ret;
+}
+
+#ifdef CONFIG_BOARD_EARLY_INIT_F
+int board_early_init_f(void)
+{
+ int err;
+ err = board_uart_init();
+ if (err) {
+ debug("UART init failed\n");
+ return err;
+ }
+#ifdef CONFIG_SYS_I2C_INIT_BOARD
+ board_i2c_init(gd->fdt_blob);
+#endif
+ return err;
+}
+#endif
+
+#ifdef CONFIG_LCD
+void exynos_cfg_lcd_gpio(void)
+{
+ struct exynos5_gpio_part1 *gpio1 =
+ (struct exynos5_gpio_part1 *)samsung_get_base_gpio_part1();
+
+ /* For Backlight */
+ s5p_gpio_cfg_pin(&gpio1->b2, 0, GPIO_OUTPUT);
+ s5p_gpio_set_value(&gpio1->b2, 0, 1);
+
+ /* LCD power on */
+ s5p_gpio_cfg_pin(&gpio1->x1, 5, GPIO_OUTPUT);
+ s5p_gpio_set_value(&gpio1->x1, 5, 1);
+
+ /* Set Hotplug detect for DP */
+ s5p_gpio_cfg_pin(&gpio1->x0, 7, GPIO_FUNC(0x3));
+}
+
+void exynos_set_dp_phy(unsigned int onoff)
+{
+ set_dp_phy_ctrl(onoff);
+}
+#endif
diff --git a/board/samsung/smdk5250/lowlevel_init.S b/board/samsung/smdk5250/lowlevel_init.S
index bc6cb6f..edc565e 100644
--- a/board/samsung/smdk5250/lowlevel_init.S
+++ b/board/samsung/smdk5250/lowlevel_init.S
@@ -75,12 +75,14 @@ lowlevel_init:
bl mem_ctrl_init
1:
+ bl arch_cpu_init
bl tzpc_init
ldmia r13!, {ip,pc}
wakeup_reset:
bl system_clock_init
bl mem_ctrl_init
+ bl arch_cpu_init
bl tzpc_init
exit_wakeup:
diff --git a/board/samsung/smdk5250/setup.h b/board/samsung/smdk5250/setup.h
index 34d8bc31..eb91d13 100644
--- a/board/samsung/smdk5250/setup.h
+++ b/board/samsung/smdk5250/setup.h
@@ -28,18 +28,6 @@
#include <config.h>
#include <asm/arch/dmc.h>
-/* TZPC : Register Offsets */
-#define TZPC0_BASE 0x10100000
-#define TZPC1_BASE 0x10110000
-#define TZPC2_BASE 0x10120000
-#define TZPC3_BASE 0x10130000
-#define TZPC4_BASE 0x10140000
-#define TZPC5_BASE 0x10150000
-#define TZPC6_BASE 0x10160000
-#define TZPC7_BASE 0x10170000
-#define TZPC8_BASE 0x10180000
-#define TZPC9_BASE 0x10190000
-
/* APLL_CON1 */
#define APLL_CON1_VAL (0x00203800)
@@ -458,18 +446,6 @@
/* CLK_GATE_IP_DISP1 */
#define CLK_GATE_DP1_ALLOW (1 << 4)
-/*
- * TZPC Register Value :
- * R0SIZE: 0x0 : Size of secured ram
- */
-#define R0SIZE 0x0
-
-/*
- * TZPC Decode Protection Register Value :
- * DECPROTXSET: 0xFF : Set Decode region to non-secure
- */
-#define DECPROTXSET 0xFF
-
#define DDR3PHY_CTRL_PHY_RESET (1 << 0)
#define DDR3PHY_CTRL_PHY_RESET_OFF (0 << 0)
@@ -590,5 +566,4 @@ void update_reset_dll(struct exynos5_dmc *, enum ddr_mode);
void sdelay(unsigned long);
void mem_ctrl_init(void);
void system_clock_init(void);
-void tzpc_init(void);
#endif
diff --git a/board/samsung/smdk5250/smdk5250.c b/board/samsung/smdk5250/smdk5250.c
index 8b09e1d..276fd41 100644
--- a/board/samsung/smdk5250/smdk5250.c
+++ b/board/samsung/smdk5250/smdk5250.c
@@ -29,6 +29,7 @@
#include <netdev.h>
#include <spi.h>
#include <asm/arch/cpu.h>
+#include <asm/arch/dwmmc.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mmc.h>
#include <asm/arch/pinmux.h>
@@ -37,39 +38,9 @@
#include <asm/arch/dp_info.h>
#include <power/pmic.h>
#include <power/max77686_pmic.h>
-#include <tmu.h>
DECLARE_GLOBAL_DATA_PTR;
-#if defined CONFIG_EXYNOS_TMU
-/*
- * Boot Time Thermal Analysis for SoC temperature threshold breach
- */
-static void boot_temp_check(void)
-{
- int temp;
-
- switch (tmu_monitor(&temp)) {
- /* Status TRIPPED ans WARNING means corresponding threshold breach */
- case TMU_STATUS_TRIPPED:
- puts("EXYNOS_TMU: TRIPPING! Device power going down ...\n");
- set_ps_hold_ctrl();
- hang();
- break;
- case TMU_STATUS_WARNING:
- puts("EXYNOS_TMU: WARNING! Temperature very high\n");
- break;
- /*
- * TMU_STATUS_INIT means something is wrong with temperature sensing
- * and TMU status was changed back from NORMAL to INIT.
- */
- case TMU_STATUS_INIT:
- default:
- debug("EXYNOS_TMU: Unknown TMU state\n");
- }
-}
-#endif
-
#ifdef CONFIG_USB_EHCI_EXYNOS
int board_usb_vbus_init(void)
{
@@ -102,14 +73,6 @@ int board_init(void)
{
gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
-#if defined CONFIG_EXYNOS_TMU
- if (tmu_init(gd->fdt_blob) != TMU_STATUS_NORMAL) {
- debug("%s: Failed to init TMU\n", __func__);
- return -1;
- }
- boot_temp_check();
-#endif
-
#ifdef CONFIG_EXYNOS_SPI
spi_init();
#endif
@@ -124,14 +87,13 @@ int board_init(void)
int dram_init(void)
{
- gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE)
- + get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE)
- + get_ram_size((long *)PHYS_SDRAM_3, PHYS_SDRAM_3_SIZE)
- + get_ram_size((long *)PHYS_SDRAM_4, PHYS_SDRAM_4_SIZE)
- + get_ram_size((long *)PHYS_SDRAM_5, PHYS_SDRAM_7_SIZE)
- + get_ram_size((long *)PHYS_SDRAM_6, PHYS_SDRAM_7_SIZE)
- + get_ram_size((long *)PHYS_SDRAM_7, PHYS_SDRAM_7_SIZE)
- + get_ram_size((long *)PHYS_SDRAM_8, PHYS_SDRAM_8_SIZE);
+ int i;
+ u32 addr;
+
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
+ gd->ram_size += get_ram_size((long *)addr, SDRAM_BANK_SIZE);
+ }
return 0;
}
@@ -254,57 +216,15 @@ int power_init_board(void)
void dram_init_banksize(void)
{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = get_ram_size((long *)PHYS_SDRAM_1,
- PHYS_SDRAM_1_SIZE);
- gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
- gd->bd->bi_dram[1].size = get_ram_size((long *)PHYS_SDRAM_2,
- PHYS_SDRAM_2_SIZE);
- gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
- gd->bd->bi_dram[2].size = get_ram_size((long *)PHYS_SDRAM_3,
- PHYS_SDRAM_3_SIZE);
- gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
- gd->bd->bi_dram[3].size = get_ram_size((long *)PHYS_SDRAM_4,
- PHYS_SDRAM_4_SIZE);
- gd->bd->bi_dram[4].start = PHYS_SDRAM_5;
- gd->bd->bi_dram[4].size = get_ram_size((long *)PHYS_SDRAM_5,
- PHYS_SDRAM_5_SIZE);
- gd->bd->bi_dram[5].start = PHYS_SDRAM_6;
- gd->bd->bi_dram[5].size = get_ram_size((long *)PHYS_SDRAM_6,
- PHYS_SDRAM_6_SIZE);
- gd->bd->bi_dram[6].start = PHYS_SDRAM_7;
- gd->bd->bi_dram[6].size = get_ram_size((long *)PHYS_SDRAM_7,
- PHYS_SDRAM_7_SIZE);
- gd->bd->bi_dram[7].start = PHYS_SDRAM_8;
- gd->bd->bi_dram[7].size = get_ram_size((long *)PHYS_SDRAM_8,
- PHYS_SDRAM_8_SIZE);
-}
-
-#ifdef CONFIG_OF_CONTROL
-static int decode_sromc(const void *blob, struct fdt_sromc *config)
-{
- int err;
- int node;
-
- node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_SROMC);
- if (node < 0) {
- debug("Could not find SROMC node\n");
- return node;
- }
-
- config->bank = fdtdec_get_int(blob, node, "bank", 0);
- config->width = fdtdec_get_int(blob, node, "width", 2);
-
- err = fdtdec_get_int_array(blob, node, "srom-timing", config->timing,
- FDT_SROM_TIMING_COUNT);
- if (err < 0) {
- debug("Could not decode SROMC configuration\n");
- return -FDT_ERR_NOTFOUND;
+ int i;
+ u32 addr, size;
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
+ size = get_ram_size((long *)addr, SDRAM_BANK_SIZE);
+ gd->bd->bi_dram[i].start = addr;
+ gd->bd->bi_dram[i].size = size;
}
-
- return 0;
}
-#endif
int board_eth_init(bd_t *bis)
{
@@ -313,27 +233,6 @@ int board_eth_init(bd_t *bis)
struct fdt_sromc config;
fdt_addr_t base_addr;
-#ifdef CONFIG_OF_CONTROL
- int node;
-
- node = decode_sromc(gd->fdt_blob, &config);
- if (node < 0) {
- debug("%s: Could not find sromc configuration\n", __func__);
- return 0;
- }
- node = fdtdec_next_compatible(gd->fdt_blob, node, COMPAT_SMSC_LAN9215);
- if (node < 0) {
- debug("%s: Could not find lan9215 configuration\n", __func__);
- return 0;
- }
-
- /* We now have a node, so any problems from now on are errors */
- base_addr = fdtdec_get_addr(gd->fdt_blob, node, "reg");
- if (base_addr == FDT_ADDR_T_NONE) {
- debug("%s: Could not find lan9215 address\n", __func__);
- return -1;
- }
-#else
/* Non-FDT configuration - bank number and timing parameters*/
config.bank = CONFIG_ENV_SROM_BANK;
config.width = 2;
@@ -346,7 +245,6 @@ int board_eth_init(bd_t *bis)
config.timing[FDT_SROM_TACP] = 0x09;
config.timing[FDT_SROM_PMC] = 0x01;
base_addr = CONFIG_SMC911X_BASE;
-#endif
/* Ethernet needs data bus width of 16 bits */
if (config.width != 2) {
@@ -376,17 +274,7 @@ int board_eth_init(bd_t *bis)
#ifdef CONFIG_DISPLAY_BOARDINFO
int checkboard(void)
{
-#ifdef CONFIG_OF_CONTROL
- const char *board_name;
-
- board_name = fdt_getprop(gd->fdt_blob, 0, "model", NULL);
- if (board_name == NULL)
- printf("\nUnknown Board\n");
- else
- printf("\nBoard: %s\n", board_name);
-#else
printf("\nBoard: SMDK5250\n");
-#endif
return 0;
}
#endif
@@ -394,48 +282,54 @@ int checkboard(void)
#ifdef CONFIG_GENERIC_MMC
int board_mmc_init(bd_t *bis)
{
- int err;
+ int err, ret = 0, index, bus_width;
+ u32 base;
err = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE);
- if (err) {
+ if (err)
debug("SDMMC0 not configured\n");
- return err;
- }
-
- err = s5p_mmc_init(0, 8);
- return err;
+ ret |= err;
+
+ /*EMMC: dwmmc Channel-0 with 8 bit bus width */
+ index = 0;
+ base = samsung_get_base_mmc() + (0x10000 * index);
+ bus_width = 8;
+ err = exynos_dwmci_add_port(index, base, bus_width, (u32)NULL);
+ if (err)
+ debug("dwmmc Channel-0 init failed\n");
+ ret |= err;
+
+ err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE);
+ if (err)
+ debug("SDMMC2 not configured\n");
+ ret |= err;
+
+ /*SD: dwmmc Channel-2 with 4 bit bus width */
+ index = 2;
+ base = samsung_get_base_mmc() + (0x10000 * index);
+ bus_width = 4;
+ err = exynos_dwmci_add_port(index, base, bus_width, (u32)NULL);
+ if (err)
+ debug("dwmmc Channel-2 init failed\n");
+ ret |= err;
+
+ return ret;
}
#endif
static int board_uart_init(void)
{
- int err;
-
- err = exynos_pinmux_config(PERIPH_ID_UART0, PINMUX_FLAG_NONE);
- if (err) {
- debug("UART0 not configured\n");
- return err;
+ int err, uart_id, ret = 0;
+
+ for (uart_id = PERIPH_ID_UART0; uart_id <= PERIPH_ID_UART3; uart_id++) {
+ err = exynos_pinmux_config(uart_id, PINMUX_FLAG_NONE);
+ if (err) {
+ debug("UART%d not configured\n",
+ (uart_id - PERIPH_ID_UART0));
+ ret |= err;
+ }
}
-
- err = exynos_pinmux_config(PERIPH_ID_UART1, PINMUX_FLAG_NONE);
- if (err) {
- debug("UART1 not configured\n");
- return err;
- }
-
- err = exynos_pinmux_config(PERIPH_ID_UART2, PINMUX_FLAG_NONE);
- if (err) {
- debug("UART2 not configured\n");
- return err;
- }
-
- err = exynos_pinmux_config(PERIPH_ID_UART3, PINMUX_FLAG_NONE);
- if (err) {
- debug("UART3 not configured\n");
- return err;
- }
-
- return 0;
+ return ret;
}
#ifdef CONFIG_BOARD_EARLY_INIT_F
@@ -448,7 +342,7 @@ int board_early_init_f(void)
return err;
}
#ifdef CONFIG_SYS_I2C_INIT_BOARD
- board_i2c_init(gd->fdt_blob);
+ board_i2c_init(NULL);
#endif
return err;
}
@@ -477,7 +371,6 @@ void exynos_set_dp_phy(unsigned int onoff)
set_dp_phy_ctrl(onoff);
}
-#ifndef CONFIG_OF_CONTROL
vidinfo_t panel_info = {
.vl_freq = 60,
.vl_col = 2560,
@@ -543,13 +436,9 @@ static struct exynos_dp_platform_data dp_platform_data = {
.edp_dev_info = &edp_info,
};
-#endif
void init_panel_info(vidinfo_t *vid)
{
-#ifndef CONFIG_OF_CONTROL
- vid->rgb_mode = MODE_RGB_P,
-
+ vid->rgb_mode = MODE_RGB_P;
exynos_set_dp_platform_data(&dp_platform_data);
-#endif
}
#endif
diff --git a/board/samsung/smdk5250/spl_boot.c b/board/samsung/smdk5250/spl_boot.c
index c0bcf46..98f2286 100644
--- a/board/samsung/smdk5250/spl_boot.c
+++ b/board/samsung/smdk5250/spl_boot.c
@@ -23,16 +23,44 @@
#include<common.h>
#include<config.h>
+#include <asm/arch-exynos/dmc.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/clk.h>
+
+#include "clock_init.h"
+
+/* Index into irom ptr table */
+enum index {
+ MMC_INDEX,
+ EMMC44_INDEX,
+ EMMC44_END_INDEX,
+ SPI_INDEX,
+ USB_INDEX,
+};
+
+/* IROM Function Pointers Table */
+u32 irom_ptr_table[] = {
+ [MMC_INDEX] = 0x02020030, /* iROM Function Pointer-SDMMC boot */
+ [EMMC44_INDEX] = 0x02020044, /* iROM Function Pointer-EMMC4.4 boot*/
+ [EMMC44_END_INDEX] = 0x02020048,/* iROM Function Pointer
+ -EMMC4.4 end boot operation */
+ [SPI_INDEX] = 0x02020058, /* iROM Function Pointer-SPI boot */
+ [USB_INDEX] = 0x02020070, /* iROM Function Pointer-USB boot*/
+ };
+
enum boot_mode {
BOOT_MODE_MMC = 4,
BOOT_MODE_SERIAL = 20,
+ BOOT_MODE_EMMC = 8, /* EMMC4.4 */
/* Boot based on Operating Mode pin settings */
BOOT_MODE_OM = 32,
BOOT_MODE_USB, /* Boot using USB download */
};
- typedef u32 (*spi_copy_func_t)(u32 offset, u32 nblock, u32 dst);
- typedef u32 (*usb_copy_func_t)(void);
+void *get_irom_func(int index)
+{
+ return (void *)*(u32 *)irom_ptr_table[index];
+}
/*
* Set/clear program flow prediction and return the previous state.
@@ -55,13 +83,15 @@ static int config_branch_prediction(int set_cr_z)
*/
void copy_uboot_to_ram(void)
{
- spi_copy_func_t spi_copy;
- usb_copy_func_t usb_copy;
-
int is_cr_z_set;
unsigned int sec_boot_check;
enum boot_mode bootmode = BOOT_MODE_OM;
- u32 (*copy_bl2)(u32, u32, u32);
+
+ u32 (*spi_copy)(u32 offset, u32 nblock, u32 dst);
+ u32 (*copy_bl2)(u32 offset, u32 nblock, u32 dst);
+ u32 (*copy_bl2_from_emmc)(u32 nblock, u32 dst);
+ void (*end_bootop_from_emmc)(void);
+ u32 (*usb_copy)(void);
/* Read iRAM location to check for secondary USB boot mode */
sec_boot_check = readl(EXYNOS_IRAM_SECONDARY_BASE);
@@ -73,14 +103,24 @@ void copy_uboot_to_ram(void)
switch (bootmode) {
case BOOT_MODE_SERIAL:
- spi_copy = *(spi_copy_func_t *)EXYNOS_COPY_SPI_FNPTR_ADDR;
+ spi_copy = get_irom_func(SPI_INDEX);
spi_copy(SPI_FLASH_UBOOT_POS, CONFIG_BL2_SIZE,
- CONFIG_SYS_TEXT_BASE);
+ CONFIG_SYS_TEXT_BASE);
break;
case BOOT_MODE_MMC:
- copy_bl2 = (void *) *(u32 *)COPY_BL2_FNPTR_ADDR;
+ copy_bl2 = get_irom_func(MMC_INDEX);
copy_bl2(BL2_START_OFFSET, BL2_SIZE_BLOC_COUNT,
- CONFIG_SYS_TEXT_BASE);
+ CONFIG_SYS_TEXT_BASE);
+ break;
+ case BOOT_MODE_EMMC:
+ /* Set the FSYS1 clock divisor value for EMMC boot */
+ emmc_boot_clk_div_set();
+
+ copy_bl2_from_emmc = get_irom_func(EMMC44_INDEX);
+ end_bootop_from_emmc = get_irom_func(EMMC44_END_INDEX);
+
+ copy_bl2_from_emmc(BL2_SIZE_BLOC_COUNT, CONFIG_SYS_TEXT_BASE);
+ end_bootop_from_emmc();
break;
case BOOT_MODE_USB:
/*
@@ -88,8 +128,7 @@ void copy_uboot_to_ram(void)
* before copy from USB device to RAM
*/
is_cr_z_set = config_branch_prediction(0);
- usb_copy = *(usb_copy_func_t *)
- EXYNOS_COPY_USB_FNPTR_ADDR;
+ usb_copy = get_irom_func(USB_INDEX);
usb_copy();
config_branch_prediction(is_cr_z_set);
break;
@@ -117,5 +156,4 @@ void board_init_r(gd_t *id, ulong dest_addr)
while (1)
;
}
-
void save_boot_params(u32 r0, u32 r1, u32 r2, u32 r3) {}
diff --git a/board/samsung/smdk5250/tzpc_init.c b/board/samsung/smdk5250/tzpc_init.c
deleted file mode 100644
index c833541..0000000
--- a/board/samsung/smdk5250/tzpc_init.c
+++ /dev/null
@@ -1,48 +0,0 @@
-/*
- * Lowlevel setup for SMDK5250 board based on S5PC520
- *
- * Copyright (C) 2012 Samsung Electronics
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <asm/arch/tzpc.h>
-#include"setup.h"
-
-/* Setting TZPC[TrustZone Protection Controller] */
-void tzpc_init(void)
-{
- struct exynos_tzpc *tzpc;
- unsigned int addr;
-
- for (addr = TZPC0_BASE; addr <= TZPC9_BASE; addr += TZPC_BASE_OFFSET) {
- tzpc = (struct exynos_tzpc *)addr;
-
- if (addr == TZPC0_BASE)
- writel(R0SIZE, &tzpc->r0size);
-
- writel(DECPROTXSET, &tzpc->decprot0set);
- writel(DECPROTXSET, &tzpc->decprot1set);
-
- if (addr != TZPC9_BASE) {
- writel(DECPROTXSET, &tzpc->decprot2set);
- writel(DECPROTXSET, &tzpc->decprot3set);
- }
- }
-}
diff --git a/board/samsung/smdkv310/lowlevel_init.S b/board/samsung/smdkv310/lowlevel_init.S
index 7a1ea98..31e0e2e 100644
--- a/board/samsung/smdkv310/lowlevel_init.S
+++ b/board/samsung/smdkv310/lowlevel_init.S
@@ -85,12 +85,14 @@ lowlevel_init:
1:
/* for UART */
bl uart_asm_init
+ bl arch_cpu_init
bl tzpc_init
pop {pc}
wakeup_reset:
bl system_clock_init
bl mem_ctrl_asm_init
+ bl arch_cpu_init
bl tzpc_init
exit_wakeup:
@@ -410,61 +412,3 @@ uart_asm_init:
nop
nop
nop
-
-/* Setting TZPC[TrustZone Protection Controller] */
-tzpc_init:
- ldr r0, =0x10110000
- mov r1, #0x0
- str r1, [r0]
- mov r1, #0xff
- str r1, [r0, #0x0804]
- str r1, [r0, #0x0810]
- str r1, [r0, #0x081C]
- str r1, [r0, #0x0828]
-
- ldr r0, =0x10120000
- mov r1, #0x0
- str r1, [r0]
- mov r1, #0xff
- str r1, [r0, #0x0804]
- str r1, [r0, #0x0810]
- str r1, [r0, #0x081C]
- str r1, [r0, #0x0828]
-
- ldr r0, =0x10130000
- mov r1, #0x0
- str r1, [r0]
- mov r1, #0xff
- str r1, [r0, #0x0804]
- str r1, [r0, #0x0810]
- str r1, [r0, #0x081C]
- str r1, [r0, #0x0828]
-
- ldr r0, =0x10140000
- mov r1, #0x0
- str r1, [r0]
- mov r1, #0xff
- str r1, [r0, #0x0804]
- str r1, [r0, #0x0810]
- str r1, [r0, #0x081C]
- str r1, [r0, #0x0828]
-
- ldr r0, =0x10150000
- mov r1, #0x0
- str r1, [r0]
- mov r1, #0xff
- str r1, [r0, #0x0804]
- str r1, [r0, #0x0810]
- str r1, [r0, #0x081C]
- str r1, [r0, #0x0828]
-
- ldr r0, =0x10160000
- mov r1, #0x0
- str r1, [r0]
- mov r1, #0xff
- str r1, [r0, #0x0804]
- str r1, [r0, #0x0810]
- str r1, [r0, #0x081C]
- str r1, [r0, #0x0828]
-
- mov pc, lr
diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c
index 638cc4d..fdbe26c 100644
--- a/board/ti/am335x/board.c
+++ b/board/ti/am335x/board.c
@@ -38,9 +38,6 @@
DECLARE_GLOBAL_DATA_PTR;
static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
-#ifdef CONFIG_SPL_BUILD
-static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE;
-#endif
/* MII mode defines */
#define MII_MODE_ENABLE 0x0
@@ -126,28 +123,7 @@ static int read_eeprom(void)
return 0;
}
-/* UART Defines */
#ifdef CONFIG_SPL_BUILD
-#define UART_RESET (0x1 << 1)
-#define UART_CLK_RUNNING_MASK 0x1
-#define UART_SMART_IDLE_EN (0x1 << 0x3)
-
-static void rtc32k_enable(void)
-{
- struct rtc_regs *rtc = (struct rtc_regs *)RTC_BASE;
-
- /*
- * Unlock the RTC's registers. For more details please see the
- * RTC_SS section of the TRM. In order to unlock we need to
- * write these specific values (keys) in this order.
- */
- writel(0x83e70b13, &rtc->kick0r);
- writel(0x95a4f1e0, &rtc->kick1r);
-
- /* Enable the RTC 32K OSC by setting bits 3 and 6. */
- writel((1 << 3) | (1 << 6), &rtc->osc);
-}
-
static const struct ddr_data ddr2_data = {
.datardsratio0 = ((MT47H128M16RT25E_RD_DQS<<30) |
(MT47H128M16RT25E_RD_DQS<<20) |
@@ -339,9 +315,6 @@ void s_init(void)
/* Enable RTC32K clock */
rtc32k_enable();
- /* UART softreset */
- u32 regVal;
-
#ifdef CONFIG_SERIAL1
enable_uart0_pin_mux();
#endif /* CONFIG_SERIAL1 */
@@ -361,17 +334,7 @@ void s_init(void)
enable_uart5_pin_mux();
#endif /* CONFIG_SERIAL6 */
- regVal = readl(&uart_base->uartsyscfg);
- regVal |= UART_RESET;
- writel(regVal, &uart_base->uartsyscfg);
- while ((readl(&uart_base->uartsyssts) &
- UART_CLK_RUNNING_MASK) != UART_CLK_RUNNING_MASK)
- ;
-
- /* Disable smart idle */
- regVal = readl(&uart_base->uartsyscfg);
- regVal |= UART_SMART_IDLE_EN;
- writel(regVal, &uart_base->uartsyscfg);
+ uart_soft_reset();
gd = &gdata;
diff --git a/board/ti/panda/panda.c b/board/ti/panda/panda.c
index 90ae29e..1da5b35 100644
--- a/board/ti/panda/panda.c
+++ b/board/ti/panda/panda.c
@@ -37,6 +37,11 @@
#endif
#define PANDA_ULPI_PHY_TYPE_GPIO 182
+#define PANDA_BOARD_ID_1_GPIO 101
+#define PANDA_ES_BOARD_ID_1_GPIO 48
+#define PANDA_BOARD_ID_2_GPIO 171
+#define PANDA_ES_BOARD_ID_3_GPIO 3
+#define PANDA_ES_BOARD_ID_4_GPIO 2
DECLARE_GLOBAL_DATA_PTR;
@@ -66,6 +71,73 @@ int board_eth_init(bd_t *bis)
return 0;
}
+/*
+* Routine: get_board_revision
+* Description: Detect if we are running on a panda revision A1-A6,
+* or an ES panda board. This can be done by reading
+* the level of GPIOs and checking the processor revisions.
+* This should result in:
+* Panda 4430:
+* GPIO171, GPIO101, GPIO182: 0 1 1 => A1-A5
+* GPIO171, GPIO101, GPIO182: 1 0 1 => A6
+* Panda ES:
+* GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2
+* GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3
+*/
+int get_board_revision(void)
+{
+ int board_id0, board_id1, board_id2;
+ int board_id3, board_id4;
+ int board_id;
+
+ int processor_rev = omap_revision();
+
+ /* Setup the mux for the common board ID pins (gpio 171 and 182) */
+ writew((IEN | M3), (*ctrl)->control_padconf_core_base + UNIPRO_TX0);
+ writew((IEN | M3), (*ctrl)->control_padconf_core_base + FREF_CLK2_OUT);
+
+ board_id0 = gpio_get_value(PANDA_ULPI_PHY_TYPE_GPIO);
+ board_id2 = gpio_get_value(PANDA_BOARD_ID_2_GPIO);
+
+ if ((processor_rev >= OMAP4460_ES1_0 &&
+ processor_rev <= OMAP4460_ES1_1)) {
+ /*
+ * Setup the mux for the ES specific board ID pins (gpio 101,
+ * 2 and 3.
+ */
+ writew((IEN | M3), (*ctrl)->control_padconf_core_base +
+ GPMC_A24);
+ writew((IEN | M3), (*ctrl)->control_padconf_core_base +
+ UNIPRO_RY0);
+ writew((IEN | M3), (*ctrl)->control_padconf_core_base +
+ UNIPRO_RX1);
+
+ board_id1 = gpio_get_value(PANDA_ES_BOARD_ID_1_GPIO);
+ board_id3 = gpio_get_value(PANDA_ES_BOARD_ID_3_GPIO);
+ board_id4 = gpio_get_value(PANDA_ES_BOARD_ID_4_GPIO);
+
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+ setenv("board_name", strcat(CONFIG_SYS_BOARD, "-es"));
+#endif
+ board_id = ((board_id4 << 4) | (board_id3 << 3) |
+ (board_id2 << 2) | (board_id1 << 1) | (board_id0));
+ } else {
+ /* Setup the mux for the Ax specific board ID pins (gpio 101) */
+ writew((IEN | M3), (*ctrl)->control_padconf_core_base +
+ FREF_CLK2_OUT);
+
+ board_id1 = gpio_get_value(PANDA_BOARD_ID_1_GPIO);
+ board_id = ((board_id2 << 2) | (board_id1 << 1) | (board_id0));
+
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+ if ((board_id >= 0x3) && (processor_rev == OMAP4430_ES2_3))
+ setenv("board_name", strcat(CONFIG_SYS_BOARD, "-a4"));
+#endif
+ }
+
+ return board_id;
+}
+
/**
* @brief misc_init_r - Configure Panda board specific configurations
* such as power configurations, ethernet initialization as phase2 of
@@ -82,11 +154,7 @@ int misc_init_r(void)
if (omap_revision() == OMAP4430_ES1_0)
return 0;
-#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
- if (omap_revision() >= OMAP4460_ES1_0 ||
- omap_revision() <= OMAP4460_ES1_1)
- setenv("board_name", strcat(CONFIG_SYS_BOARD, "-es"));
-#endif
+ get_board_revision();
gpio_direction_input(PANDA_ULPI_PHY_TYPE_GPIO);
phy_type = gpio_get_value(PANDA_ULPI_PHY_TYPE_GPIO);
@@ -106,7 +174,7 @@ int misc_init_r(void)
auxclk |= AUXCLK_ENABLE_MASK;
writel(auxclk, &scrm->auxclk3);
- } else {
+ } else {
/* ULPI PHY supplied by auxclk1 derived from PER dpll */
debug("ULPI PHY supplied by auxclk1\n");
@@ -151,9 +219,9 @@ void set_muxconf_regs_essential(void)
if (omap_revision() >= OMAP4460_ES1_0)
do_set_mux((*ctrl)->control_padconf_wkup_base,
- wkup_padconf_array_essential_4460,
- sizeof(wkup_padconf_array_essential_4460) /
- sizeof(struct pad_conf_entry));
+ wkup_padconf_array_essential_4460,
+ sizeof(wkup_padconf_array_essential_4460) /
+ sizeof(struct pad_conf_entry));
}
void set_muxconf_regs_non_essential(void)
@@ -165,14 +233,14 @@ void set_muxconf_regs_non_essential(void)
if (omap_revision() < OMAP4460_ES1_0)
do_set_mux((*ctrl)->control_padconf_core_base,
- core_padconf_array_non_essential_4430,
- sizeof(core_padconf_array_non_essential_4430) /
- sizeof(struct pad_conf_entry));
+ core_padconf_array_non_essential_4430,
+ sizeof(core_padconf_array_non_essential_4430) /
+ sizeof(struct pad_conf_entry));
else
do_set_mux((*ctrl)->control_padconf_core_base,
- core_padconf_array_non_essential_4460,
- sizeof(core_padconf_array_non_essential_4460) /
- sizeof(struct pad_conf_entry));
+ core_padconf_array_non_essential_4460,
+ sizeof(core_padconf_array_non_essential_4460) /
+ sizeof(struct pad_conf_entry));
do_set_mux((*ctrl)->control_padconf_wkup_base,
wkup_padconf_array_non_essential,
@@ -181,9 +249,9 @@ void set_muxconf_regs_non_essential(void)
if (omap_revision() < OMAP4460_ES1_0)
do_set_mux((*ctrl)->control_padconf_wkup_base,
- wkup_padconf_array_non_essential_4430,
- sizeof(wkup_padconf_array_non_essential_4430) /
- sizeof(struct pad_conf_entry));
+ wkup_padconf_array_non_essential_4430,
+ sizeof(wkup_padconf_array_non_essential_4430) /
+ sizeof(struct pad_conf_entry));
}
#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC)
diff --git a/board/ti/ti814x/evm.c b/board/ti/ti814x/evm.c
index 4759b16..6ad3dd8 100644
--- a/board/ti/ti814x/evm.c
+++ b/board/ti/ti814x/evm.c
@@ -37,49 +37,16 @@ DECLARE_GLOBAL_DATA_PTR;
#ifdef CONFIG_SPL_BUILD
static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
-static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE;
#endif
static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
/* UART Defines */
#ifdef CONFIG_SPL_BUILD
-#define UART_RESET (0x1 << 1)
-#define UART_CLK_RUNNING_MASK 0x1
-#define UART_SMART_IDLE_EN (0x1 << 0x3)
-
-static void rtc32k_enable(void)
-{
- struct rtc_regs *rtc = (struct rtc_regs *)RTC_BASE;
-
- /*
- * Unlock the RTC's registers. For more details please see the
- * RTC_SS section of the TRM. In order to unlock we need to
- * write these specific values (keys) in this order.
- */
- writel(0x83e70b13, &rtc->kick0r);
- writel(0x95a4f1e0, &rtc->kick1r);
-
- /* Enable the RTC 32K OSC by setting bits 3 and 6. */
- writel((1 << 3) | (1 << 6), &rtc->osc);
-}
-
static void uart_enable(void)
{
- u32 regVal;
-
/* UART softreset */
- regVal = readl(&uart_base->uartsyscfg);
- regVal |= UART_RESET;
- writel(regVal, &uart_base->uartsyscfg);
- while ((readl(&uart_base->uartsyssts) &
- UART_CLK_RUNNING_MASK) != UART_CLK_RUNNING_MASK)
- ;
-
- /* Disable smart idle */
- regVal = readl(&uart_base->uartsyscfg);
- regVal |= UART_SMART_IDLE_EN;
- writel(regVal, &uart_base->uartsyscfg);
+ uart_soft_reset();
}
static void wdt_disable(void)
diff --git a/board/vpac270/u-boot-spl.lds b/board/vpac270/u-boot-spl.lds
index 61d1154..1a3ef92 100644
--- a/board/vpac270/u-boot-spl.lds
+++ b/board/vpac270/u-boot-spl.lds
@@ -67,11 +67,6 @@ SECTIONS
__rel_dyn_end = .;
}
- .dynsym : {
- __dynsym_start = .;
- *(.dynsym)
- }
-
. = ALIGN(0x800);
_end = .;
@@ -84,6 +79,7 @@ SECTIONS
}
/DISCARD/ : { *(.bss*) }
+ /DISCARD/ : { *(.dynsym) }
/DISCARD/ : { *(.dynstr*) }
/DISCARD/ : { *(.dynsym*) }
/DISCARD/ : { *(.dynamic*) }