diff options
Diffstat (limited to 'board')
| -rw-r--r-- | board/freescale/mx50_rdp/flash_header.S | 52 |
1 files changed, 34 insertions, 18 deletions
diff --git a/board/freescale/mx50_rdp/flash_header.S b/board/freescale/mx50_rdp/flash_header.S index 6ce2fa5..f6b01c8 100644 --- a/board/freescale/mx50_rdp/flash_header.S +++ b/board/freescale/mx50_rdp/flash_header.S @@ -35,15 +35,15 @@ /*============================================================================= * Pu calibration based on 240 Ohm *===========================================================================*/ - ldr r1, =0x0 + ldr r1, =0x1 pu_loop: cmp r1, #0x20 beq pu_out - // (pd + 1) << 24 | (pu + 1) << 16 - ldr r2, =0x0 - add r2, r2, #0x1 - add r1, r1, #0x1 + // (pd - 1) << 24 | (pu - 1) << 16 + ldr r2, =0x1 + sub r2, r2, #0x1 + sub r1, r1, #0x1 mov r3, r1, LSL #16 orr r3, r3, r2, LSL #24 @@ -88,14 +88,14 @@ pu_out: /*============================================================================= * PD calibration start (based on pu) *===========================================================================*/ - ldr r2, =0x0 + ldr r2, =0x1 pd_loop: cmp r2, #0xf beq pd_out - // (pd + 1) << 24 | (pu + 1) << 16 | 1 << 4 - add r2, r2, #0x1 - add r1, r1, #0x1 + // (pd - 1) << 24 | (pu - 1) << 16 | 1 << 4 + sub r2, r2, #0x1 + sub r1, r1, #0x1 mov r3, r2, lsl #24 orr r3, r3, r1, lsl #16 orr r3, r3, #0x10 @@ -143,21 +143,20 @@ pd_out: // Pd calibration result in r2 sub r2, r2, #0x2 -#if defined(CONFIG_LPDDR2) // Pd add 3 add r2, r2, #0x3 /*============================================================================= * Pu calibration based on pd value *===========================================================================*/ - ldr r1, =0x0 + ldr r1, =0x1 pu_loop_pd: cmp r1, #0x20 beq pu_out_pd - // (pd + 1) << 24 | (pu + 1) << 16 | 1 << 4 - add r2, r2, #0x1 - add r1, r1, #0x1 + // (pd - 1) << 24 | (pu - 1) << 16 | 1 << 4 + sub r2, r2, #0x1 + sub r1, r1, #0x1 mov r3, r2, LSL #24 orr r3, r3, r1, LSL #16 orr r3, r3, #0x10 @@ -199,7 +198,6 @@ pu_delay_pd: pu_out_pd: // Pu calibration result in r1 sub r1, r1, #0x1 -#endif /*============================================================================= * Software load PU/PD value,PU is stored in r1, and PD is stored in r2 @@ -210,9 +208,9 @@ pu_out_pd: // Set SW_CFG2 str r3, [r0, #0x12c] - // ((pd + 1) << 24) | ((pu + 1) <<16) - add r2, r2, #0x1 - add r1, r1, #0x1 + // ((pd - 1) << 24) | ((pu - 1) <<16) + sub r2, r2, #0x1 + sub r1, r1, #0x1 mov r3, r2, LSL #24 orr r3, r3, r1, LSL #16 // Load PU, pu_pd_sel=0 @@ -369,8 +367,17 @@ wait_pll1_lock: //setmem /32 0x53fa86ac = 0x04000000 //IOMUXC_SW_PAD_CTL_GRP_DDR_TYPE, ddr_sel=2'b01 (LPDDR2) str r1, [r0, #0xac] +//setmem /32 0x53fa866c = 0x00000200 //IOMUXC_SW_PAD_CTL_GRP_DDRMODE_CTL +// [9] DDR_INPUT=1 (DQS: differential input mode) + mov r2, #0x00000200 + str r2, [r0, #0x6c] +//setmem /32 0x53fa868c = 0x0 // IOMUXC_SW_PAD_CTL_GRP_DDRMODE +// [9] DDR_INPUT=0 (DATA: CMOS input type) + mov r2, #0x0 + str r2, [r0, #0x8c] //setmem /32 0x53fa8670 = 0x00000000 //IOMUXC_SW_PAD_CTL_GRP_DDRPKE // bit 7: PKE=0 (All ddr pads except DQS) + mov r2, #0x0 str r2, [r0, #0x70] //setmem /32 0x53fa86a4 = 0x00200000 //IOMUXC_SW_PAD_CTL_GRP_CTLDS, dse=3'b100 @@ -525,6 +532,15 @@ wait_pll1_lock: //setmem /32 0x1400004c = 0x00010000 ldr r1, =0x00010000 str r1, [r0, #0x4c] +//setmem /32 0x14000050 = 0x00000000, lowpower mode + ldr r1, =0x00000000 + str r1, [r0, #0x50] +//setmem /32 0x14000054 = 0x00000000, lowpower mode + ldr r1, =0x00000000 + str r1, [r0, #0x54] +//setmem /32 0x14000058 = 0x00000000, lowpower mode + ldr r1, =0x00000000 + str r1, [r0, #0x58] //setmem /32 0x1400005c = 0x02000000 ldr r1, =0x02000000 str r1, [r0, #0x5c] |