summaryrefslogtreecommitdiff
path: root/board/ti/beagle
diff options
context:
space:
mode:
Diffstat (limited to 'board/ti/beagle')
-rw-r--r--board/ti/beagle/beagle.c101
1 files changed, 0 insertions, 101 deletions
diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c
index 2cca6da..624ff70 100644
--- a/board/ti/beagle/beagle.c
+++ b/board/ti/beagle/beagle.c
@@ -42,15 +42,6 @@
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
#include <asm/mach-types.h>
-#ifdef CONFIG_USB_EHCI
-#include <usb.h>
-#include <asm/arch/clocks.h>
-#include <asm/arch/clocks_omap3.h>
-#include <asm/arch/ehci_omap3.h>
-/* from drivers/usb/host/ehci-core.h */
-extern struct ehci_hccr *hccr;
-extern volatile struct ehci_hcor *hcor;
-#endif
#include "beagle.h"
#include <command.h>
@@ -452,104 +443,12 @@ int board_mmc_init(bd_t *bis)
#endif
#ifdef CONFIG_USB_EHCI
-
-#define GPIO_PHY_RESET 147
-
-/* Reset is needed otherwise the kernel-driver will throw an error. */
-int ehci_hcd_stop(void)
-{
- pr_debug("Resetting OMAP3 EHCI\n");
- gpio_set_value(GPIO_PHY_RESET, 0);
- writel(OMAP_UHH_SYSCONFIG_SOFTRESET, OMAP3_UHH_BASE + OMAP_UHH_SYSCONFIG);
- /* disable USB clocks */
- struct prcm *prcm_base = (struct prcm *)PRCM_BASE;
- sr32(&prcm_base->iclken_usbhost, 0, 1, 0);
- sr32(&prcm_base->fclken_usbhost, 0, 2, 0);
- sr32(&prcm_base->iclken3_core, 2, 1, 0);
- sr32(&prcm_base->fclken3_core, 2, 1, 0);
- return 0;
-}
-
/* Call usb_stop() before starting the kernel */
void show_boot_progress(int val)
{
if(val == 15)
usb_stop();
}
-
-/*
- * Initialize the OMAP3 EHCI controller and PHY on the BeagleBoard.
- * Based on "drivers/usb/host/ehci-omap.c" from Linux 2.6.37.
- * See there for additional Copyrights.
- */
-int ehci_hcd_init(void)
-{
- pr_debug("Initializing OMAP3 ECHI\n");
-
- /* Put the PHY in RESET */
- gpio_request(GPIO_PHY_RESET, "");
- gpio_direction_output(GPIO_PHY_RESET, 0);
- gpio_set_value(GPIO_PHY_RESET, 0);
-
- /* Hold the PHY in RESET for enough time till DIR is high */
- /* Refer: ISSUE1 */
- udelay(10);
-
- struct prcm *prcm_base = (struct prcm *)PRCM_BASE;
- /* Enable USBHOST_L3_ICLK (USBHOST_MICLK) */
- sr32(&prcm_base->iclken_usbhost, 0, 1, 1);
- /*
- * Enable USBHOST_48M_FCLK (USBHOST_FCLK1)
- * and USBHOST_120M_FCLK (USBHOST_FCLK2)
- */
- sr32(&prcm_base->fclken_usbhost, 0, 2, 3);
- /* Enable USBTTL_ICLK */
- sr32(&prcm_base->iclken3_core, 2, 1, 1);
- /* Enable USBTTL_FCLK */
- sr32(&prcm_base->fclken3_core, 2, 1, 1);
- pr_debug("USB clocks enabled\n");
-
- /* perform TLL soft reset, and wait until reset is complete */
- writel(OMAP_USBTLL_SYSCONFIG_SOFTRESET,
- OMAP3_USBTLL_BASE + OMAP_USBTLL_SYSCONFIG);
- /* Wait for TLL reset to complete */
- while (!(readl(OMAP3_USBTLL_BASE + OMAP_USBTLL_SYSSTATUS)
- & OMAP_USBTLL_SYSSTATUS_RESETDONE));
- pr_debug("TLL reset done\n");
-
- writel(OMAP_USBTLL_SYSCONFIG_ENAWAKEUP |
- OMAP_USBTLL_SYSCONFIG_SIDLEMODE |
- OMAP_USBTLL_SYSCONFIG_CACTIVITY,
- OMAP3_USBTLL_BASE + OMAP_USBTLL_SYSCONFIG);
-
- /* Put UHH in NoIdle/NoStandby mode */
- writel(OMAP_UHH_SYSCONFIG_ENAWAKEUP
- | OMAP_UHH_SYSCONFIG_SIDLEMODE
- | OMAP_UHH_SYSCONFIG_CACTIVITY
- | OMAP_UHH_SYSCONFIG_MIDLEMODE,
- OMAP3_UHH_BASE + OMAP_UHH_SYSCONFIG);
-
- /* setup burst configurations */
- writel(OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN
- | OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN
- | OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN,
- OMAP3_UHH_BASE + OMAP_UHH_HOSTCONFIG);
-
- /*
- * Refer ISSUE1:
- * Hold the PHY in RESET for enough time till
- * PHY is settled and ready
- */
- udelay(10);
- gpio_set_value(GPIO_PHY_RESET, 1);
-
- hccr = (struct ehci_hccr *)(OMAP3_EHCI_BASE);
- hcor = (struct ehci_hcor *)(OMAP3_EHCI_BASE + 0x10);
-
- pr_debug("OMAP3 EHCI init done\n");
- return 0;
-}
-
#endif /* CONFIG_USB_EHCI */
#ifndef CONFIG_SPL_BUILD