diff options
Diffstat (limited to 'board/sbc8548/README')
| -rw-r--r-- | board/sbc8548/README | 26 |
1 files changed, 13 insertions, 13 deletions
diff --git a/board/sbc8548/README b/board/sbc8548/README index feac5e3..0def245 100644 --- a/board/sbc8548/README +++ b/board/sbc8548/README @@ -7,10 +7,10 @@ memory. It also has 128MB SDRAM 100MHz LBC memory, with both a PCI-e, and a PCI-X slot, dual mini-DB9 for UART, and dual RJ-45 for eTSEC ethernet connections. -U-boot Configuration: +U-Boot Configuration: ===================== -The following possible u-boot configuration targets are available: +The following possible U-Boot configuration targets are available: 1) sbc8548_config 2) sbc8548_PCI_33_config @@ -23,7 +23,7 @@ of each choice are listed below. Choice #1 does not enable CONFIG_PCI, and assumes that the PCI slot will be left empty (M66EN high), and so the board will operate with -a base clock of 66MHz. Note that you need both PCI enabled in u-boot +a base clock of 66MHz. Note that you need both PCI enabled in U-Boot and linux in order to have functional PCI under linux. The second enables PCI support and builds for a 33MHz clock rate. Note @@ -100,13 +100,13 @@ from the board's socket to resolve the above i2c address overlap issue and allow SPD autodetection of RAM to work. -Updating U-boot with U-boot: +Updating U-Boot with U-Boot: ============================ -Note that versions of u-boot up to and including 2009.08 had u-boot stored +Note that versions of U-Boot up to and including 2009.08 had U-Boot stored at 0xfff8_0000 -> 0xffff_ffff (512k). Currently it is being stored from 0xfffa_0000 -> 0xffff_ffff (384k). If you use an old macro/script to -update u-boot with u-boot and it uses the old address, you will render +update U-Boot with U-Boot and it uses the old address, you will render your board inoperable, and you will require JTAG recovery. The following steps list how to update with the current address: @@ -120,11 +120,11 @@ The following steps list how to update with the current address: protect on all The "md" steps in the above are just a precautionary step that allow -you to confirm the u-boot version that was downloaded, and then confirm +you to confirm the U-Boot version that was downloaded, and then confirm that it was copied to flash. The above assumes that you are using the default board settings which -have u-boot in the 8MB flash, tied to /CS0. +have U-Boot in the 8MB flash, tied to /CS0. If you are running the default 8MB /CS0 settings but want to store an image in the SODIMM that is built with CONFIG_SYS_ALT_BOOT enabled, @@ -139,7 +139,7 @@ image in the SODIMM that is built with CONFIG_SYS_ALT_BOOT enabled, protect on all Finally, if you are running the alternate 64MB /CS0 settings and want -to update the in-use u-boot image, then (again with CONFIG_SYS_ALT_BOOT +to update the in-use U-Boot image, then (again with CONFIG_SYS_ALT_BOOT enabled) the steps will become: tftp u-boot.bin @@ -155,7 +155,7 @@ Hardware Reference: =================== The following contains some summary information on hardware settings -that are relevant to u-boot, based on the board manual. For the +that are relevant to U-Boot, based on the board manual. For the most up to date and complete details of the board, please request the reference manual ERG-00327-001.pdf from www.windriver.com @@ -166,7 +166,7 @@ Sodimm flash: intel V28F128Jx, 16384x8 (4 devices) at 0xfb80_0000 Note that this address reflects the default setting for the JTAG debugging tools, but since the alignment is - rather inconvenient, u-boot puts it at 0xec00_0000. + rather inconvenient, U-Boot puts it at 0xec00_0000. Jumpers: @@ -193,7 +193,7 @@ is jumpered parallel to the LBC-SDRAM, then /CS0 is for the SODIMM flash and /CS6 is for the boot flash. Note that in this alternate setting, you also need to switch SW2.8 to ON. See the setting CONFIG_SYS_ALT_BOOT if you want to use this setting -and boot u-boot from the 64MB SODIMM +and boot U-Boot from the 64MB SODIMM Switches: @@ -257,7 +257,7 @@ fb80_0000 ff7f_ffff CS6 32 SODIMM flash (64MB) [*] ff80_0000 ffff_ffff CS0 8 Boot flash (8MB) [*] fb80 represents the default programmed by WR JTAG register files, - but u-boot places the flash at either ec00 or fc00 based on JP12. + but U-Boot places the flash at either ec00 or fc00 based on JP12. The EPLD on CS5 demuxes the following devices at the following offsets: |