diff options
Diffstat (limited to 'board/sandburst')
-rw-r--r-- | board/sandburst/common/ppc440gx_i2c.c | 494 | ||||
-rw-r--r-- | board/sandburst/common/ppc440gx_i2c.h | 44 | ||||
-rw-r--r-- | board/sandburst/common/sb_common.c | 103 | ||||
-rw-r--r-- | board/sandburst/common/sb_common.h | 1 | ||||
-rw-r--r-- | board/sandburst/karef/Makefile | 3 | ||||
-rw-r--r-- | board/sandburst/karef/karef.c | 6 | ||||
-rw-r--r-- | board/sandburst/metrobox/Makefile | 3 | ||||
-rw-r--r-- | board/sandburst/metrobox/metrobox.c | 6 |
8 files changed, 54 insertions, 606 deletions
diff --git a/board/sandburst/common/ppc440gx_i2c.c b/board/sandburst/common/ppc440gx_i2c.c deleted file mode 100644 index 1d7f17c..0000000 --- a/board/sandburst/common/ppc440gx_i2c.c +++ /dev/null @@ -1,494 +0,0 @@ -/* - * Copyright (C) 2005 Sandburst Corporation - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * Ported from arch/powerpc/cpu/ppc4xx/i2c.c by AS HARNOIS by - * Travis B. Sawyer - * Sandburst Corporation. - */ -#include <common.h> -#include <asm/ppc4xx.h> -#include <asm/ppc4xx-i2c.h> -#include <i2c.h> -#include <command.h> -#include "ppc440gx_i2c.h" -#include <asm/io.h> - -#ifdef CONFIG_I2C_BUS1 - -#define IIC_OK 0 -#define IIC_NOK 1 -#define IIC_NOK_LA 2 /* Lost arbitration */ -#define IIC_NOK_ICT 3 /* Incomplete transfer */ -#define IIC_NOK_XFRA 4 /* Transfer aborted */ -#define IIC_NOK_DATA 5 /* No data in buffer */ -#define IIC_NOK_TOUT 6 /* Transfer timeout */ - -#define IIC_TIMEOUT 1 /* 1 second */ -#if defined(CONFIG_SYS_I2C_NOPROBES) -static uchar i2c_no_probes[] = CONFIG_SYS_I2C_NOPROBES; -#endif - -static struct ppc4xx_i2c *i2c = (struct ppc4xx_i2c *)I2C_REGISTERS_BUS1_BASE_ADDRESS; - -static void _i2c_bus1_reset (void) -{ - int i, status; - - /* Reset status register */ - /* write 1 in SCMP and IRQA to clear these fields */ - out_8 (IIC_STS1, 0x0A); - - /* write 1 in IRQP IRQD LA ICT XFRA to clear these fields */ - out_8 (IIC_EXTSTS1, 0x8F); - __asm__ volatile ("eieio"); - - /* - * Get current state, reset bus - * only if no transfers are pending. - */ - i = 10; - do { - /* Get status */ - status = in_8 (IIC_STS1); - udelay (500); /* 500us */ - i--; - } while ((status & IIC_STS_PT) && (i > 0)); - /* Soft reset controller */ - status = in_8 (IIC_XTCNTLSS1); - out_8 (IIC_XTCNTLSS1, (status | IIC_XTCNTLSS_SRST)); - __asm__ volatile ("eieio"); - - /* make sure where in initial state, data hi, clock hi */ - out_8 (IIC_DIRECTCNTL1, 0xC); - for (i = 0; i < 10; i++) { - if ((in_8 (IIC_DIRECTCNTL1) & 0x3) != 0x3) { - /* clock until we get to known state */ - out_8 (IIC_DIRECTCNTL1, 0x8); /* clock lo */ - udelay (100); /* 100us */ - out_8 (IIC_DIRECTCNTL1, 0xC); /* clock hi */ - udelay (100); /* 100us */ - } else { - break; - } - } - /* send start condition */ - out_8 (IIC_DIRECTCNTL1, 0x4); - udelay (1000); /* 1ms */ - /* send stop condition */ - out_8 (IIC_DIRECTCNTL1, 0xC); - udelay (1000); /* 1ms */ - /* Unreset controller */ - out_8 (IIC_XTCNTLSS1, (status & ~IIC_XTCNTLSS_SRST)); - udelay (1000); /* 1ms */ -} - -void i2c1_init (int speed, int slaveadd) -{ - sys_info_t sysInfo; - unsigned long freqOPB; - int val, divisor; - -#ifdef CONFIG_SYS_I2C_INIT_BOARD - /* call board specific i2c bus reset routine before accessing the */ - /* environment, which might be in a chip on that bus. For details */ - /* about this problem see doc/I2C_Edge_Conditions. */ - i2c_init_board(); -#endif - - /* Handle possible failed I2C state */ - /* FIXME: put this into i2c_init_board()? */ - _i2c_bus1_reset (); - - /* clear lo master address */ - out_8 (IIC_LMADR1, 0); - - /* clear hi master address */ - out_8 (IIC_HMADR1, 0); - - /* clear lo slave address */ - out_8 (IIC_LSADR1, 0); - - /* clear hi slave address */ - out_8 (IIC_HSADR1, 0); - - /* Clock divide Register */ - /* get OPB frequency */ - get_sys_info (&sysInfo); - freqOPB = sysInfo.freqPLB / sysInfo.pllOpbDiv; - /* set divisor according to freqOPB */ - divisor = (freqOPB - 1) / 10000000; - if (divisor == 0) - divisor = 1; - out_8 (IIC_CLKDIV1, divisor); - - /* no interrupts */ - out_8 (IIC_INTRMSK1, 0); - - /* clear transfer count */ - out_8 (IIC_XFRCNT1, 0); - - /* clear extended control & stat */ - /* write 1 in SRC SRS SWC SWS to clear these fields */ - out_8 (IIC_XTCNTLSS1, 0xF0); - - /* Mode Control Register - Flush Slave/Master data buffer */ - out_8 (IIC_MDCNTL1, IIC_MDCNTL_FSDB | IIC_MDCNTL_FMDB); - __asm__ volatile ("eieio"); - - - val = in_8(IIC_MDCNTL1); - __asm__ volatile ("eieio"); - - /* Ignore General Call, slave transfers are ignored, - disable interrupts, exit unknown bus state, enable hold - SCL - 100kHz normaly or FastMode for 400kHz and above - */ - - val |= IIC_MDCNTL_EUBS|IIC_MDCNTL_HSCL; - if( speed >= 400000 ){ - val |= IIC_MDCNTL_FSM; - } - out_8 (IIC_MDCNTL1, val); - - /* clear control reg */ - out_8 (IIC_CNTL1, 0x00); - __asm__ volatile ("eieio"); - -} - -/* - This code tries to use the features of the 405GP i2c - controller. It will transfer up to 4 bytes in one pass - on the loop. It only does out_8(lbz) to the buffer when it - is possible to do out16(lhz) transfers. - - cmd_type is 0 for write 1 for read. - - addr_len can take any value from 0-255, it is only limited - by the char, we could make it larger if needed. If it is - 0 we skip the address write cycle. - - Typical case is a Write of an addr followd by a Read. The - IBM FAQ does not cover this. On the last byte of the write - we don't set the creg CHT bit, and on the first bytes of the - read we set the RPST bit. - - It does not support address only transfers, there must be - a data part. If you want to write the address yourself, put - it in the data pointer. - - It does not support transfer to/from address 0. - - It does not check XFRCNT. -*/ -static -int i2c_transfer1(unsigned char cmd_type, - unsigned char chip, - unsigned char addr[], - unsigned char addr_len, - unsigned char data[], - unsigned short data_len ) -{ - unsigned char* ptr; - int reading; - int tran,cnt; - int result; - int status; - int i; - uchar creg; - - if( data == 0 || data_len == 0 ){ - /*Don't support data transfer of no length or to address 0*/ - printf( "i2c_transfer: bad call\n" ); - return IIC_NOK; - } - if( addr && addr_len ){ - ptr = addr; - cnt = addr_len; - reading = 0; - }else{ - ptr = data; - cnt = data_len; - reading = cmd_type; - } - - /*Clear Stop Complete Bit*/ - out_8(IIC_STS1,IIC_STS_SCMP); - /* Check init */ - i=10; - do { - /* Get status */ - status = in_8(IIC_STS1); - __asm__ volatile("eieio"); - i--; - } while ((status & IIC_STS_PT) && (i>0)); - - if (status & IIC_STS_PT) { - result = IIC_NOK_TOUT; - return(result); - } - /*flush the Master/Slave Databuffers*/ - out_8(IIC_MDCNTL1, ((in_8(IIC_MDCNTL1))|IIC_MDCNTL_FMDB|IIC_MDCNTL_FSDB)); - /*need to wait 4 OPB clocks? code below should take that long*/ - - /* 7-bit adressing */ - out_8(IIC_HMADR1,0); - out_8(IIC_LMADR1, chip); - __asm__ volatile("eieio"); - - tran = 0; - result = IIC_OK; - creg = 0; - - while ( tran != cnt && (result == IIC_OK)) { - int bc,j; - - /* Control register = - Normal transfer, 7-bits adressing, Transfer up to bc bytes, Normal start, - Transfer is a sequence of transfers - */ - creg |= IIC_CNTL_PT; - - bc = (cnt - tran) > 4 ? 4 : - cnt - tran; - creg |= (bc-1)<<4; - /* if the real cmd type is write continue trans*/ - if ( (!cmd_type && (ptr == addr)) || ((tran+bc) != cnt) ) - creg |= IIC_CNTL_CHT; - - if (reading) - creg |= IIC_CNTL_READ; - else { - for(j=0; j<bc; j++) { - /* Set buffer */ - out_8(IIC_MDBUF1,ptr[tran+j]); - __asm__ volatile("eieio"); - } - } - out_8(IIC_CNTL1, creg ); - __asm__ volatile("eieio"); - - /* Transfer is in progress - we have to wait for upto 5 bytes of data - 1 byte chip address+r/w bit then bc bytes - of data. - udelay(10) is 1 bit time at 100khz - Doubled for slop. 20 is too small. - */ - i=2*5*8; - do { - /* Get status */ - status = in_8(IIC_STS1); - __asm__ volatile("eieio"); - udelay (10); - i--; - } while ((status & IIC_STS_PT) && !(status & IIC_STS_ERR) - && (i>0)); - - if (status & IIC_STS_ERR) { - result = IIC_NOK; - status = in_8 (IIC_EXTSTS1); - /* Lost arbitration? */ - if (status & IIC_EXTSTS_LA) - result = IIC_NOK_LA; - /* Incomplete transfer? */ - if (status & IIC_EXTSTS_ICT) - result = IIC_NOK_ICT; - /* Transfer aborted? */ - if (status & IIC_EXTSTS_XFRA) - result = IIC_NOK_XFRA; - } else if ( status & IIC_STS_PT) { - result = IIC_NOK_TOUT; - } - /* Command is reading => get buffer */ - if ((reading) && (result == IIC_OK)) { - /* Are there data in buffer */ - if (status & IIC_STS_MDBS) { - /* - even if we have data we have to wait 4OPB clocks - for it to hit the front of the FIFO, after that - we can just read. We should check XFCNT here and - if the FIFO is full there is no need to wait. - */ - udelay (1); - for(j=0;j<bc;j++) { - ptr[tran+j] = in_8(IIC_MDBUF1); - __asm__ volatile("eieio"); - } - } else - result = IIC_NOK_DATA; - } - creg = 0; - tran+=bc; - if( ptr == addr && tran == cnt ) { - ptr = data; - cnt = data_len; - tran = 0; - reading = cmd_type; - if( reading ) - creg = IIC_CNTL_RPST; - } - } - return (result); -} - -int i2c_probe1 (uchar chip) -{ - uchar buf[1]; - - buf[0] = 0; - - /* - * What is needed is to send the chip address and verify that the - * address was <ACK>ed (i.e. there was a chip at that address which - * drove the data line low). - */ - return(i2c_transfer1 (1, chip << 1, 0,0, buf, 1) != 0); -} - - -int i2c_read1 (uchar chip, uint addr, int alen, uchar * buffer, int len) -{ - uchar xaddr[4]; - int ret; - - if ( alen > 4 ) { - printf ("I2C read: addr len %d not supported\n", alen); - return 1; - } - - if ( alen > 0 ) { - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - } - - -#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW - /* - * EEPROM chips that implement "address overflow" are ones - * like Catalyst 24WC04/08/16 which has 9/10/11 bits of - * address and the extra bits end up in the "chip address" - * bit slots. This makes a 24WC08 (1Kbyte) chip look like - * four 256 byte chips. - * - * Note that we consider the length of the address field to - * still be one byte because the extra address bits are - * hidden in the chip address. - */ - if( alen > 0 ) - chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); -#endif - if( (ret = i2c_transfer1( 1, chip<<1, &xaddr[4-alen], alen, buffer, len )) != 0) { - printf( "I2c read: failed %d\n", ret); - return 1; - } - return 0; -} - -int i2c_write1 (uchar chip, uint addr, int alen, uchar * buffer, int len) -{ - uchar xaddr[4]; - - if ( alen > 4 ) { - printf ("I2C write: addr len %d not supported\n", alen); - return 1; - - } - if ( alen > 0 ) { - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - } - -#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW - /* - * EEPROM chips that implement "address overflow" are ones - * like Catalyst 24WC04/08/16 which has 9/10/11 bits of - * address and the extra bits end up in the "chip address" - * bit slots. This makes a 24WC08 (1Kbyte) chip look like - * four 256 byte chips. - * - * Note that we consider the length of the address field to - * still be one byte because the extra address bits are - * hidden in the chip address. - */ - if( alen > 0 ) - chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); -#endif - - return (i2c_transfer1( 0, chip<<1, &xaddr[4-alen], alen, buffer, len ) != 0); -} - -/*----------------------------------------------------------------------- - * Read a register - */ -uchar i2c_reg_read1(uchar i2c_addr, uchar reg) -{ - uchar buf; - - i2c_read1(i2c_addr, reg, 1, &buf, (uchar)1); - - return(buf); -} - -/*----------------------------------------------------------------------- - * Write a register - */ -void i2c_reg_write1(uchar i2c_addr, uchar reg, uchar val) -{ - i2c_write1(i2c_addr, reg, 1, &val, 1); -} - - -int do_i2c1_probe(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) -{ - int j; -#if defined(CONFIG_SYS_I2C_NOPROBES) - int k, skip; -#endif - - puts ("Valid chip addresses:"); - for(j = 0; j < 128; j++) { -#if defined(CONFIG_SYS_I2C_NOPROBES) - skip = 0; - for (k = 0; k < sizeof(i2c_no_probes); k++){ - if (j == i2c_no_probes[k]){ - skip = 1; - break; - } - } - if (skip) - continue; -#endif - if(i2c_probe1(j) == 0) { - printf(" %02X", j); - } - } - putc ('\n'); - -#if defined(CONFIG_SYS_I2C_NOPROBES) - puts ("Excluded chip addresses:"); - for( k = 0; k < sizeof(i2c_no_probes); k++ ) - printf(" %02X", i2c_no_probes[k] ); - putc ('\n'); -#endif - - return 0; -} - -U_BOOT_CMD( - iprobe1, 1, 1, do_i2c1_probe, - "probe to discover valid I2C chip addresses", - "" -); - -#endif /* CONFIG_I2C_BUS1 */ diff --git a/board/sandburst/common/ppc440gx_i2c.h b/board/sandburst/common/ppc440gx_i2c.h deleted file mode 100644 index b1179bc..0000000 --- a/board/sandburst/common/ppc440gx_i2c.h +++ /dev/null @@ -1,44 +0,0 @@ -/* - * Copyright (C) 2005 Sandburst Corporation - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * Ported from i2c driver for ppc4xx by AS HARNOIS by - * Travis B. Sawyer - * Sandburst Corporation - */ -#include <common.h> -#include <asm/ppc4xx.h> -#include <asm/ppc4xx-i2c.h> -#include <i2c.h> - -#ifdef CONFIG_HARD_I2C - -#define I2C_BUS1_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x00000500) -#define I2C_REGISTERS_BUS1_BASE_ADDRESS I2C_BUS1_BASE_ADDR -#define IIC_MDBUF1 (&i2c->mdbuf) -#define IIC_SDBUF1 (&i2c->sdbuf) -#define IIC_LMADR1 (&i2c->lmadr) -#define IIC_HMADR1 (&i2c->hmadr) -#define IIC_CNTL1 (&i2c->cntl) -#define IIC_MDCNTL1 (&i2c->mdcntl) -#define IIC_STS1 (&i2c->sts) -#define IIC_EXTSTS1 (&i2c->extsts) -#define IIC_LSADR1 (&i2c->lsadr) -#define IIC_HSADR1 (&i2c->hsadr) -#define IIC_CLKDIV1 (&i2c->clkdiv) -#define IIC_INTRMSK1 (&i2c->intrmsk) -#define IIC_XFRCNT1 (&i2c->xfrcnt) -#define IIC_XTCNTLSS1 (&i2c->xtcntlss) -#define IIC_DIRECTCNTL1 (&i2c->directcntl) - -void i2c1_init (int speed, int slaveadd); -int i2c_probe1 (uchar chip); -int i2c_read1 (uchar chip, uint addr, int alen, uchar * buffer, int len); -int i2c_write1 (uchar chip, uint addr, int alen, uchar * buffer, int len); -uchar i2c_reg_read1(uchar i2c_addr, uchar reg); -void i2c_reg_write1(uchar i2c_addr, uchar reg, uchar val); - -#endif /* CONFIG_HARD_I2C */ diff --git a/board/sandburst/common/sb_common.c b/board/sandburst/common/sb_common.c index 12334df..b579812 100644 --- a/board/sandburst/common/sb_common.c +++ b/board/sandburst/common/sb_common.c @@ -10,7 +10,6 @@ #include <asm/io.h> #include <spd_sdram.h> #include <i2c.h> -#include "ppc440gx_i2c.h" #include "sb_common.h" DECLARE_GLOBAL_DATA_PTR; @@ -68,7 +67,7 @@ unsigned short sbcommon_get_serial_number(void) /* Get the board serial number from eeprom */ /* Initialize I2C */ - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(0); /* Read 256 bytes in EEPROM */ i2c_read (0x50, 0, 1, buff, 0x100); @@ -94,85 +93,87 @@ void sbcommon_fans(void) * Attempt to turn on 2 of the fans... * Need to go through the bridge */ + i2c_set_bus_num(1); puts ("FANS: "); /* select fan4 through the bridge */ - i2c_reg_write1(0x73, /* addr */ - 0x00, /* reg */ - 0x08); /* val = bus 4 */ + i2c_reg_write(0x73, /* addr */ + 0x00, /* reg */ + 0x08); /* val = bus 4 */ /* Turn on FAN 4 */ - i2c_reg_write1(0x2e, - 1, - 0x80); + i2c_reg_write(0x2e, + 1, + 0x80); - i2c_reg_write1(0x2e, - 0, - 0x19); + i2c_reg_write(0x2e, + 0, + 0x19); /* Deselect bus 4 on the bridge */ - i2c_reg_write1(0x73, - 0x00, - 0x00); + i2c_reg_write(0x73, + 0x00, + 0x00); /* select fan3 through the bridge */ - i2c_reg_write1(0x73, /* addr */ - 0x00, /* reg */ - 0x04); /* val = bus 3 */ + i2c_reg_write(0x73, /* addr */ + 0x00, /* reg */ + 0x04); /* val = bus 3 */ /* Turn on FAN 3 */ - i2c_reg_write1(0x2e, - 1, - 0x80); + i2c_reg_write(0x2e, + 1, + 0x80); - i2c_reg_write1(0x2e, - 0, - 0x19); + i2c_reg_write(0x2e, + 0, + 0x19); /* Deselect bus 3 on the bridge */ - i2c_reg_write1(0x73, - 0x00, - 0x00); + i2c_reg_write(0x73, + 0x00, + 0x00); /* select fan2 through the bridge */ - i2c_reg_write1(0x73, /* addr */ - 0x00, /* reg */ - 0x02); /* val = bus 4 */ + i2c_reg_write(0x73, /* addr */ + 0x00, /* reg */ + 0x02); /* val = bus 4 */ /* Turn on FAN 2 */ - i2c_reg_write1(0x2e, - 1, - 0x80); + i2c_reg_write(0x2e, + 1, + 0x80); - i2c_reg_write1(0x2e, - 0, - 0x19); + i2c_reg_write(0x2e, + 0, + 0x19); /* Deselect bus 2 on the bridge */ - i2c_reg_write1(0x73, - 0x00, - 0x00); + i2c_reg_write(0x73, + 0x00, + 0x00); /* select fan1 through the bridge */ - i2c_reg_write1(0x73, /* addr */ - 0x00, /* reg */ - 0x01); /* val = bus 0 */ + i2c_reg_write(0x73, /* addr */ + 0x00, /* reg */ + 0x01); /* val = bus 0 */ /* Turn on FAN 1 */ - i2c_reg_write1(0x2e, - 1, - 0x80); + i2c_reg_write(0x2e, + 1, + 0x80); - i2c_reg_write1(0x2e, - 0, - 0x19); + i2c_reg_write(0x2e, + 0, + 0x19); /* Deselect bus 1 on the bridge */ - i2c_reg_write1(0x73, - 0x00, - 0x00); + i2c_reg_write(0x73, + 0x00, + 0x00); puts ("on\n"); + i2c_set_bus_num(0); return; @@ -303,7 +304,7 @@ void board_get_enetaddr(int macaddr_idx, uchar *enet) if (0 == macaddr_idx) { /* Initialize I2C */ - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(0); /* Read 256 bytes in EEPROM */ i2c_read (0x50, 0, 1, buff, 0x100); diff --git a/board/sandburst/common/sb_common.h b/board/sandburst/common/sb_common.h index c86061c..8716eac 100644 --- a/board/sandburst/common/sb_common.h +++ b/board/sandburst/common/sb_common.h @@ -12,7 +12,6 @@ #include <asm/io.h> #include <spd_sdram.h> #include <i2c.h> -#include "ppc440gx_i2c.h" /* * GPIO Settings diff --git a/board/sandburst/karef/Makefile b/board/sandburst/karef/Makefile index 9cceb47..af758f9 100644 --- a/board/sandburst/karef/Makefile +++ b/board/sandburst/karef/Makefile @@ -24,8 +24,7 @@ CFLAGS += -DBUILDUSER='"$(BUILDUSER)"' LIB = $(obj)lib$(BOARD).o -COBJS = $(BOARD).o ../common/flash.o ../common/ppc440gx_i2c.o \ - ../common/sb_common.o +COBJS = $(BOARD).o ../common/flash.o ../common/sb_common.o SOBJS = init.o diff --git a/board/sandburst/karef/karef.c b/board/sandburst/karef/karef.c index 93681c1..683d68b 100644 --- a/board/sandburst/karef/karef.c +++ b/board/sandburst/karef/karef.c @@ -16,7 +16,6 @@ #include <spd_sdram.h> #include <i2c.h> #include "../common/sb_common.h" -#include "../common/ppc440gx_i2c.h" #if defined(CONFIG_HAS_ETH0) || defined(CONFIG_HAS_ETH1) || \ defined(CONFIG_HAS_ETH2) || defined(CONFIG_HAS_ETH3) #include <net.h> @@ -322,11 +321,6 @@ int checkboard (void) ************************************************************************/ int misc_init_f (void) { - /* Turn on i2c bus 1 */ - puts ("I2C1: "); - i2c1_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - puts ("ready\n"); - /* Turn on fans 3 & 4 */ sbcommon_fans(); diff --git a/board/sandburst/metrobox/Makefile b/board/sandburst/metrobox/Makefile index 4dbd6ed..163f2b9 100644 --- a/board/sandburst/metrobox/Makefile +++ b/board/sandburst/metrobox/Makefile @@ -23,8 +23,7 @@ CFLAGS += -DBUILDUSER='"$(BUILDUSER)"' LIB = $(obj)lib$(BOARD).o -COBJS = $(BOARD).o ../common/flash.o ../common/ppc440gx_i2c.o \ - ../common/sb_common.o +COBJS = $(BOARD).o ../common/flash.o ../common/sb_common.o SOBJS = init.o SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) diff --git a/board/sandburst/metrobox/metrobox.c b/board/sandburst/metrobox/metrobox.c index 8d50796..5bc7f2f 100644 --- a/board/sandburst/metrobox/metrobox.c +++ b/board/sandburst/metrobox/metrobox.c @@ -14,7 +14,6 @@ #include <asm/io.h> #include <spd_sdram.h> #include <i2c.h> -#include "../common/ppc440gx_i2c.h" #include "../common/sb_common.h" #if defined(CONFIG_HAS_ETH0) || defined(CONFIG_HAS_ETH1) || \ defined(CONFIG_HAS_ETH2) || defined(CONFIG_HAS_ETH3) @@ -289,11 +288,6 @@ int checkboard (void) ************************************************************************/ int misc_init_f (void) { - /* Turn on i2c bus 1 */ - puts ("I2C1: "); - i2c1_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - puts ("ready\n"); - /* Turn on fans */ sbcommon_fans(); |