summaryrefslogtreecommitdiff
path: root/board/sacsng/sacsng.c
diff options
context:
space:
mode:
Diffstat (limited to 'board/sacsng/sacsng.c')
-rw-r--r--board/sacsng/sacsng.c848
1 files changed, 0 insertions, 848 deletions
diff --git a/board/sacsng/sacsng.c b/board/sacsng/sacsng.c
deleted file mode 100644
index 91c4987..0000000
--- a/board/sacsng/sacsng.c
+++ /dev/null
@@ -1,848 +0,0 @@
-/*
- * (C) Copyright 2002
- * Custom IDEAS, Inc. <www.cideas.com>
- * Gerald Van Baren <vanbaren@cideas.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/u-boot.h>
-#include <ioports.h>
-#include <mpc8260.h>
-#include <i2c.h>
-#include <spi.h>
-#include <command.h>
-
-#ifdef CONFIG_SHOW_BOOT_PROGRESS
-#include <status_led.h>
-#endif
-
-#ifdef CONFIG_ETHER_LOOPBACK_TEST
-extern void eth_loopback_test(void);
-#endif /* CONFIG_ETHER_LOOPBACK_TEST */
-
-#include "clkinit.h"
-#include "ioconfig.h" /* I/O configuration table */
-
-/*
- * PBI Page Based Interleaving
- * PSDMR_PBI page based interleaving
- * 0 bank based interleaving
- * External Address Multiplexing (EAMUX) adds a clock to address cycles
- * (this can help with marginal board layouts)
- * PSDMR_EAMUX adds a clock
- * 0 no extra clock
- * Buffer Command (BUFCMD) adds a clock to command cycles.
- * PSDMR_BUFCMD adds a clock
- * 0 no extra clock
- */
-#define CONFIG_PBI PSDMR_PBI
-#define PESSIMISTIC_SDRAM 0
-#define EAMUX 0 /* EST requires EAMUX */
-#define BUFCMD 0
-
-/*
- * ADC/DAC Defines:
- */
-#define INITIAL_SAMPLE_RATE 10016 /* Initial Daq sample rate */
-#define INITIAL_RIGHT_JUST 0 /* Initial DAC right justification */
-#define INITIAL_MCLK_DIVIDE 0 /* Initial MCLK Divide */
-#define INITIAL_SAMPLE_64X 1 /* Initial 64x clocking mode */
-#define INITIAL_SAMPLE_128X 0 /* Initial 128x clocking mode */
-
-/*
- * ADC Defines:
- */
-#define I2C_ADC_1_ADDR 0x0E /* I2C Address of the ADC #1 */
-#define I2C_ADC_2_ADDR 0x0F /* I2C Address of the ADC #2 */
-
-#define ADC_SDATA1_MASK 0x00020000 /* PA14 - CH12SDATA_PU */
-#define ADC_SDATA2_MASK 0x00010000 /* PA15 - CH34SDATA_PU */
-
-#define ADC_VREF_CAP 100 /* VREF capacitor in uF */
-#define ADC_INITIAL_DELAY (10 * ADC_VREF_CAP) /* 10 usec per uF, in usec */
-#define ADC_SDATA_DELAY 100 /* ADC SDATA release delay in usec */
-#define ADC_CAL_DELAY (1000000 / INITIAL_SAMPLE_RATE * 4500)
- /* Wait at least 4100 LRCLK's */
-
-#define ADC_REG1_FRAME_START 0x80 /* Frame start */
-#define ADC_REG1_GROUND_CAL 0x40 /* Ground calibration enable */
-#define ADC_REG1_ANA_MOD_PDOWN 0x20 /* Analog modulator section in power down */
-#define ADC_REG1_DIG_MOD_PDOWN 0x10 /* Digital modulator section in power down */
-
-#define ADC_REG2_128x 0x80 /* Oversample at 128x */
-#define ADC_REG2_CAL 0x40 /* System calibration enable */
-#define ADC_REG2_CHANGE_SIGN 0x20 /* Change sign enable */
-#define ADC_REG2_LR_DISABLE 0x10 /* Left/Right output disable */
-#define ADC_REG2_HIGH_PASS_DIS 0x08 /* High pass filter disable */
-#define ADC_REG2_SLAVE_MODE 0x04 /* Slave mode */
-#define ADC_REG2_DFS 0x02 /* Digital format select */
-#define ADC_REG2_MUTE 0x01 /* Mute */
-
-#define ADC_REG7_ADDR_ENABLE 0x80 /* Address enable */
-#define ADC_REG7_PEAK_ENABLE 0x40 /* Peak enable */
-#define ADC_REG7_PEAK_UPDATE 0x20 /* Peak update */
-#define ADC_REG7_PEAK_FORMAT 0x10 /* Peak display format */
-#define ADC_REG7_DIG_FILT_PDOWN 0x04 /* Digital filter power down enable */
-#define ADC_REG7_FIR2_IN_EN 0x02 /* External FIR2 input enable */
-#define ADC_REG7_PSYCHO_EN 0x01 /* External pyscho filter input enable */
-
-/*
- * DAC Defines:
- */
-
-#define I2C_DAC_ADDR 0x11 /* I2C Address of the DAC */
-
-#define DAC_RST_MASK 0x00008000 /* PA16 - DAC_RST* */
-#define DAC_RESET_DELAY 100 /* DAC reset delay in usec */
-#define DAC_INITIAL_DELAY 5000 /* DAC initialization delay in usec */
-
-#define DAC_REG1_AMUTE 0x80 /* Auto-mute */
-
-#define DAC_REG1_LEFT_JUST_24_BIT (0 << 4) /* Fmt 0: Left justified 24 bit */
-#define DAC_REG1_I2S_24_BIT (1 << 4) /* Fmt 1: I2S up to 24 bit */
-#define DAC_REG1_RIGHT_JUST_16BIT (2 << 4) /* Fmt 2: Right justified 16 bit */
-#define DAC_REG1_RIGHT_JUST_24BIT (3 << 4) /* Fmt 3: Right justified 24 bit */
-#define DAC_REG1_RIGHT_JUST_20BIT (4 << 4) /* Fmt 4: Right justified 20 bit */
-#define DAC_REG1_RIGHT_JUST_18BIT (5 << 4) /* Fmt 5: Right justified 18 bit */
-
-#define DAC_REG1_DEM_NO (0 << 2) /* No De-emphasis */
-#define DAC_REG1_DEM_44KHZ (1 << 2) /* 44.1KHz De-emphasis */
-#define DAC_REG1_DEM_48KHZ (2 << 2) /* 48KHz De-emphasis */
-#define DAC_REG1_DEM_32KHZ (3 << 2) /* 32KHz De-emphasis */
-
-#define DAC_REG1_SINGLE 0 /* 4- 50KHz sample rate */
-#define DAC_REG1_DOUBLE 1 /* 50-100KHz sample rate */
-#define DAC_REG1_QUAD 2 /* 100-200KHz sample rate */
-#define DAC_REG1_DSD 3 /* Direct Stream Data, DSD */
-
-#define DAC_REG5_INVERT_A 0x80 /* Invert channel A */
-#define DAC_REG5_INVERT_B 0x40 /* Invert channel B */
-#define DAC_REG5_I2C_MODE 0x20 /* Control port (I2C) mode */
-#define DAC_REG5_POWER_DOWN 0x10 /* Power down mode */
-#define DAC_REG5_MUTEC_A_B 0x08 /* Mutec A=B */
-#define DAC_REG5_FREEZE 0x04 /* Freeze */
-#define DAC_REG5_MCLK_DIV 0x02 /* MCLK divide by 2 */
-#define DAC_REG5_RESERVED 0x01 /* Reserved */
-
-/*
- * Check Board Identity:
- */
-
-int checkboard(void)
-{
- printf("SACSng\n");
-
- return 0;
-}
-
-phys_size_t initdram(int board_type)
-{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile memctl8260_t *memctl = &immap->im_memctl;
- volatile uchar c = 0;
- volatile uchar *ramaddr = (uchar *)(CONFIG_SYS_SDRAM_BASE + 0x8);
- uint psdmr = CONFIG_SYS_PSDMR;
- int i;
- uint psrt = 14; /* for no SPD */
- uint chipselects = 1; /* for no SPD */
- uint sdram_size = CONFIG_SYS_SDRAM0_SIZE * 1024 * 1024; /* for no SPD */
- uint or = CONFIG_SYS_OR2_PRELIM; /* for no SPD */
-
-#ifdef SDRAM_SPD_ADDR
- uint data_width;
- uint rows;
- uint banks;
- uint cols;
- uint caslatency;
- uint width;
- uint rowst;
- uint sdam;
- uint bsma;
- uint sda10;
- u_char data;
- u_char cksum;
- int j;
-#endif
-
-#ifdef SDRAM_SPD_ADDR
- /* Keep the compiler from complaining about potentially uninitialized vars */
- data_width = chipselects = rows = banks = cols = caslatency = psrt =
- 0;
-
- /*
- * Read the SDRAM SPD EEPROM via I2C.
- */
- i2c_read(SDRAM_SPD_ADDR, 0, 1, &data, 1);
- cksum = data;
- for (j = 1; j < 64; j++) { /* read only the checksummed bytes */
- /* note: the I2C address autoincrements when alen == 0 */
- i2c_read(SDRAM_SPD_ADDR, 0, 0, &data, 1);
- if (j == 5)
- chipselects = data & 0x0F;
- else if (j == 6)
- data_width = data;
- else if (j == 7)
- data_width |= data << 8;
- else if (j == 3)
- rows = data & 0x0F;
- else if (j == 4)
- cols = data & 0x0F;
- else if (j == 12) {
- /*
- * Refresh rate: this assumes the prescaler is set to
- * approximately 1uSec per tick.
- */
- switch (data & 0x7F) {
- default:
- case 0:
- psrt = 14; /* 15.625uS */
- break;
- case 1:
- psrt = 2; /* 3.9uS */
- break;
- case 2:
- psrt = 6; /* 7.8uS */
- break;
- case 3:
- psrt = 29; /* 31.3uS */
- break;
- case 4:
- psrt = 60; /* 62.5uS */
- break;
- case 5:
- psrt = 120; /* 125uS */
- break;
- }
- } else if (j == 17)
- banks = data;
- else if (j == 18) {
- caslatency = 3; /* default CL */
-#if(PESSIMISTIC_SDRAM)
- if ((data & 0x04) != 0)
- caslatency = 3;
- else if ((data & 0x02) != 0)
- caslatency = 2;
- else if ((data & 0x01) != 0)
- caslatency = 1;
-#else
- if ((data & 0x01) != 0)
- caslatency = 1;
- else if ((data & 0x02) != 0)
- caslatency = 2;
- else if ((data & 0x04) != 0)
- caslatency = 3;
-#endif
- else {
- printf("WARNING: Unknown CAS latency 0x%02X, using 3\n", data);
- }
- } else if (j == 63) {
- if (data != cksum) {
- printf("WARNING: Configuration data checksum failure:" " is 0x%02x, calculated 0x%02x\n", data, cksum);
- }
- }
- cksum += data;
- }
-
- /* We don't trust CL less than 2 (only saw it on an old 16MByte DIMM) */
- if (caslatency < 2) {
- printf("WARNING: CL was %d, forcing to 2\n", caslatency);
- caslatency = 2;
- }
- if (rows > 14) {
- printf("WARNING: This doesn't look good, rows = %d, should be <= 14\n",
- rows);
- rows = 14;
- }
- if (cols > 11) {
- printf("WARNING: This doesn't look good, columns = %d, should be <= 11\n",
- cols);
- cols = 11;
- }
-
- if ((data_width != 64) && (data_width != 72)) {
- printf("WARNING: SDRAM width unsupported, is %d, expected 64 or 72.\n",
- data_width);
- }
- width = 3; /* 2^3 = 8 bytes = 64 bits wide */
- /*
- * Convert banks into log2(banks)
- */
- if (banks == 2)
- banks = 1;
- else if (banks == 4)
- banks = 2;
- else if (banks == 8)
- banks = 3;
-
- sdram_size = 1 << (rows + cols + banks + width);
-
-#if(CONFIG_PBI == 0) /* bank-based interleaving */
- rowst = ((32 - 6) - (rows + cols + width)) * 2;
-#else
- rowst = 32 - (rows + banks + cols + width);
-#endif
-
- or = ~(sdram_size - 1) | /* SDAM address mask */
- ((banks - 1) << 13) | /* banks per device */
- (rowst << 9) | /* rowst */
- ((rows - 9) << 6); /* numr */
-
- memctl->memc_or2 = or;
-
- /*
- * SDAM specifies the number of columns that are multiplexed
- * (reference AN2165/D), defined to be (columns - 6) for page
- * interleave, (columns - 8) for bank interleave.
- *
- * BSMA is 14 - max(rows, cols). The bank select lines come
- * into play above the highest "address" line going into the
- * the SDRAM.
- */
-#if(CONFIG_PBI == 0) /* bank-based interleaving */
- sdam = cols - 8;
- bsma = ((31 - width) - 14) - ((rows > cols) ? rows : cols);
- sda10 = sdam + 2;
-#else
- sdam = cols - 6;
- bsma = ((31 - width) - 14) - ((rows > cols) ? rows : cols);
- sda10 = sdam;
-#endif
-#if(PESSIMISTIC_SDRAM)
- psdmr = (CONFIG_PBI | PSDMR_RFEN | PSDMR_RFRC_16_CLK |
- PSDMR_PRETOACT_8W | PSDMR_ACTTORW_8W | PSDMR_WRC_4C |
- PSDMR_EAMUX | PSDMR_BUFCMD) | caslatency |
- ((caslatency - 1) << 6) | /* LDOTOPRE is CL - 1 */
- (sdam << 24) | (bsma << 21) | (sda10 << 18);
-#else
- psdmr = (CONFIG_PBI | PSDMR_RFEN | PSDMR_RFRC_7_CLK |
- PSDMR_PRETOACT_3W | /* 1 for 7E parts (fast PC-133) */
- PSDMR_ACTTORW_2W | /* 1 for 7E parts (fast PC-133) */
- PSDMR_WRC_1C | /* 1 clock + 7nSec */
- EAMUX | BUFCMD) |
- caslatency | ((caslatency - 1) << 6) | /* LDOTOPRE is CL - 1 */
- (sdam << 24) | (bsma << 21) | (sda10 << 18);
-#endif
-#endif
-
- /*
- * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35):
- *
- * "At system reset, initialization software must set up the
- * programmable parameters in the memory controller banks registers
- * (ORx, BRx, P/LSDMR). After all memory parameters are configured,
- * system software should execute the following initialization sequence
- * for each SDRAM device.
- *
- * 1. Issue a PRECHARGE-ALL-BANKS command
- * 2. Issue eight CBR REFRESH commands
- * 3. Issue a MODE-SET command to initialize the mode register
- *
- * Quote from Micron MT48LC8M16A2 data sheet:
- *
- * "...the SDRAM requires a 100uS delay prior to issuing any
- * command other than a COMMAND INHIBIT or NOP. Starting at some
- * point during this 100uS period and continuing at least through
- * the end of this period, COMMAND INHIBIT or NOP commands should
- * be applied."
- *
- * "Once the 100uS delay has been satisfied with at least one COMMAND
- * INHIBIT or NOP command having been applied, a /PRECHARGE command/
- * should be applied. All banks must then be precharged, thereby
- * placing the device in the all banks idle state."
- *
- * "Once in the idle state, /two/ AUTO REFRESH cycles must be
- * performed. After the AUTO REFRESH cycles are complete, the
- * SDRAM is ready for mode register programming."
- *
- * (/emphasis/ mine, gvb)
- *
- * The way I interpret this, Micron start up sequence is:
- * 1. Issue a PRECHARGE-BANK command (initial precharge)
- * 2. Issue a PRECHARGE-ALL-BANKS command ("all banks ... precharged")
- * 3. Issue two (presumably, doing eight is OK) CBR REFRESH commands
- * 4. Issue a MODE-SET command to initialize the mode register
- *
- * --------
- *
- * The initial commands are executed by setting P/LSDMR[OP] and
- * accessing the SDRAM with a single-byte transaction."
- *
- * The appropriate BRx/ORx registers have already been set when we
- * get here. The SDRAM can be accessed at the address CONFIG_SYS_SDRAM_BASE.
- */
-
- memctl->memc_mptpr = CONFIG_SYS_MPTPR;
- memctl->memc_psrt = psrt;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_PREA;
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR;
- for (i = 0; i < 8; i++)
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_MRW;
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN;
- *ramaddr = c;
-
- /*
- * Do it a second time for the second set of chips if the DIMM has
- * two chip selects (double sided).
- */
- if (chipselects > 1) {
- ramaddr += sdram_size;
-
- memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM + sdram_size;
- memctl->memc_or3 = or;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_PREA;
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR;
- for (i = 0; i < 8; i++)
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_MRW;
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN;
- *ramaddr = c;
- }
-
- /* return total ram size */
- return (sdram_size * chipselects);
-}
-
-/*-----------------------------------------------------------------------
- * Board Control Functions
- */
-void board_poweroff(void)
-{
- while (1); /* hang forever */
-}
-
-
-#ifdef CONFIG_MISC_INIT_R
-/* ------------------------------------------------------------------------- */
-int misc_init_r(void)
-{
- /*
- * Note: iop is used by the I2C macros, and iopa by the ADC/DAC initialization.
- */
- volatile ioport_t *iopa =
- ioport_addr((immap_t *)CONFIG_SYS_IMMR, 0 /* port A */ );
- volatile ioport_t *iop =
- ioport_addr((immap_t *)CONFIG_SYS_IMMR, I2C_PORT);
-
- int reg; /* I2C register value */
- char *ep; /* Environment pointer */
- char str_buf[12]; /* sprintf output buffer */
- int sample_rate; /* ADC/DAC sample rate */
- int sample_64x; /* Use 64/4 clocking for the ADC/DAC */
- int sample_128x; /* Use 128/4 clocking for the ADC/DAC */
- int right_just; /* Is the data to the DAC right justified? */
- int mclk_divide; /* MCLK Divide */
- int quiet; /* Quiet or minimal output mode */
-
- quiet = 0;
-
- if ((ep = getenv("quiet")) != NULL)
- quiet = simple_strtol(ep, NULL, 10);
- else
- setenv("quiet", "0");
-
- /*
- * SACSng custom initialization:
- * Start the ADC and DAC clocks, since the Crystal parts do not
- * work on the I2C bus until the clocks are running.
- */
-
- sample_rate = INITIAL_SAMPLE_RATE;
- if ((ep = getenv("DaqSampleRate")) != NULL)
- sample_rate = simple_strtol(ep, NULL, 10);
-
- sample_64x = INITIAL_SAMPLE_64X;
- sample_128x = INITIAL_SAMPLE_128X;
- if ((ep = getenv("Daq64xSampling")) != NULL) {
- sample_64x = simple_strtol(ep, NULL, 10);
- if (sample_64x)
- sample_128x = 0;
- else
- sample_128x = 1;
- } else {
- if ((ep = getenv("Daq128xSampling")) != NULL) {
- sample_128x = simple_strtol(ep, NULL, 10);
- if (sample_128x)
- sample_64x = 0;
- else
- sample_64x = 1;
- }
- }
-
- /*
- * Stop the clocks and wait for at least 1 LRCLK period
- * to make sure the clocking has really stopped.
- */
- Daq_Stop_Clocks();
- udelay((1000000 / sample_rate) * NUM_LRCLKS_TO_STABILIZE);
-
- /*
- * Initialize the clocks with the new rates
- */
- Daq_Init_Clocks(sample_rate, sample_64x);
- sample_rate = Daq_Get_SampleRate();
-
- /*
- * Start the clocks and wait for at least 1 LRCLK period
- * to make sure the clocking has become stable.
- */
- Daq_Start_Clocks(sample_rate);
- udelay((1000000 / sample_rate) * NUM_LRCLKS_TO_STABILIZE);
-
- sprintf(str_buf, "%d", sample_rate);
- setenv("DaqSampleRate", str_buf);
-
- if (sample_64x) {
- setenv("Daq64xSampling", "1");
- setenv("Daq128xSampling", NULL);
- } else {
- setenv("Daq64xSampling", NULL);
- setenv("Daq128xSampling", "1");
- }
-
- /*
- * Display the ADC/DAC clocking information
- */
- if (!quiet)
- Daq_Display_Clocks();
-
- /*
- * Determine the DAC data justification
- */
-
- right_just = INITIAL_RIGHT_JUST;
- if ((ep = getenv("DaqDACRightJustified")) != NULL)
- right_just = simple_strtol(ep, NULL, 10);
-
- sprintf(str_buf, "%d", right_just);
- setenv("DaqDACRightJustified", str_buf);
-
- /*
- * Determine the DAC MCLK Divide
- */
-
- mclk_divide = INITIAL_MCLK_DIVIDE;
- if ((ep = getenv("DaqDACMClockDivide")) != NULL)
- mclk_divide = simple_strtol(ep, NULL, 10);
-
- sprintf(str_buf, "%d", mclk_divide);
- setenv("DaqDACMClockDivide", str_buf);
-
- /*
- * Initializing the I2C address in the Crystal A/Ds:
- *
- * 1) Wait for VREF cap to settle (10uSec per uF)
- * 2) Release pullup on SDATA
- * 3) Write the I2C address to register 6
- * 4) Enable address matching by setting the MSB in register 7
- */
-
- if (!quiet)
- printf("Initializing the ADC...\n");
-
- udelay(ADC_INITIAL_DELAY); /* 10uSec per uF of VREF cap */
-
- iopa->pdat &= ~ADC_SDATA1_MASK; /* release SDATA1 */
- udelay(ADC_SDATA_DELAY); /* arbitrary settling time */
-
- i2c_reg_write(0x00, 0x06, I2C_ADC_1_ADDR); /* set address */
- i2c_reg_write(I2C_ADC_1_ADDR, 0x07, /* turn on ADDREN */
- ADC_REG7_ADDR_ENABLE);
-
- i2c_reg_write(I2C_ADC_1_ADDR, 0x02, /* 128x, slave mode, !HPEN */
- (sample_64x ? 0 : ADC_REG2_128x) |
- ADC_REG2_HIGH_PASS_DIS | ADC_REG2_SLAVE_MODE);
-
- reg = i2c_reg_read(I2C_ADC_1_ADDR, 0x06) & 0x7F;
- if (reg != I2C_ADC_1_ADDR) {
- printf("Init of ADC U10 failed: address is 0x%02X should be 0x%02X\n",
- reg, I2C_ADC_1_ADDR);
- }
-
- iopa->pdat &= ~ADC_SDATA2_MASK; /* release SDATA2 */
- udelay(ADC_SDATA_DELAY); /* arbitrary settling time */
-
- /* set address (do not set ADDREN yet) */
- i2c_reg_write(0x00, 0x06, I2C_ADC_2_ADDR);
-
- i2c_reg_write(I2C_ADC_2_ADDR, 0x02, /* 64x, slave mode, !HPEN */
- (sample_64x ? 0 : ADC_REG2_128x) |
- ADC_REG2_HIGH_PASS_DIS | ADC_REG2_SLAVE_MODE);
-
- reg = i2c_reg_read(I2C_ADC_2_ADDR, 0x06) & 0x7F;
- if (reg != I2C_ADC_2_ADDR) {
- printf("Init of ADC U15 failed: address is 0x%02X should be 0x%02X\n",
- reg, I2C_ADC_2_ADDR);
- }
-
- i2c_reg_write(I2C_ADC_1_ADDR, 0x01, /* set FSTART and GNDCAL */
- ADC_REG1_FRAME_START | ADC_REG1_GROUND_CAL);
-
- i2c_reg_write(I2C_ADC_1_ADDR, 0x02, /* Start calibration */
- (sample_64x ? 0 : ADC_REG2_128x) |
- ADC_REG2_CAL |
- ADC_REG2_HIGH_PASS_DIS | ADC_REG2_SLAVE_MODE);
-
- udelay(ADC_CAL_DELAY); /* a minimum of 4100 LRCLKs */
- i2c_reg_write(I2C_ADC_1_ADDR, 0x01, 0x00); /* remove GNDCAL */
-
- /*
- * Now that we have synchronized the ADC's, enable address
- * selection on the second ADC as well as the first.
- */
- i2c_reg_write(I2C_ADC_2_ADDR, 0x07, ADC_REG7_ADDR_ENABLE);
-
- /*
- * Initialize the Crystal DAC
- *
- * Two of the config lines are used for I2C so we have to set them
- * to the proper initialization state without inadvertantly
- * sending an I2C "start" sequence. When we bring the I2C back to
- * the normal state, we send an I2C "stop" sequence.
- */
- if (!quiet)
- printf("Initializing the DAC...\n");
-
- /*
- * Bring the I2C clock and data lines low for initialization
- */
- I2C_SCL(0);
- I2C_DELAY;
- I2C_SDA(0);
- I2C_ACTIVE;
- I2C_DELAY;
-
- /* Reset the DAC */
- iopa->pdat &= ~DAC_RST_MASK;
- udelay(DAC_RESET_DELAY);
-
- /* Release the DAC reset */
- iopa->pdat |= DAC_RST_MASK;
- udelay(DAC_INITIAL_DELAY);
-
- /*
- * Cause the DAC to:
- * Enable control port (I2C mode)
- * Going into power down
- */
- i2c_reg_write(I2C_DAC_ADDR, 0x05,
- DAC_REG5_I2C_MODE | DAC_REG5_POWER_DOWN);
-
- /*
- * Cause the DAC to:
- * Enable control port (I2C mode)
- * Going into power down
- * . MCLK divide by 1
- * . MCLK divide by 2
- */
- i2c_reg_write(I2C_DAC_ADDR, 0x05,
- DAC_REG5_I2C_MODE |
- DAC_REG5_POWER_DOWN |
- (mclk_divide ? DAC_REG5_MCLK_DIV : 0));
-
- /*
- * Cause the DAC to:
- * Auto-mute disabled
- * . Format 0, left justified 24 bits
- * . Format 3, right justified 24 bits
- * No de-emphasis
- * . Single speed mode
- * . Double speed mode
- */
- i2c_reg_write(I2C_DAC_ADDR, 0x01,
- (right_just ? DAC_REG1_RIGHT_JUST_24BIT :
- DAC_REG1_LEFT_JUST_24_BIT) |
- DAC_REG1_DEM_NO |
- (sample_rate >=
- 50000 ? DAC_REG1_DOUBLE : DAC_REG1_SINGLE));
-
- sprintf(str_buf, "%d",
- sample_rate >= 50000 ? DAC_REG1_DOUBLE : DAC_REG1_SINGLE);
- setenv("DaqDACFunctionalMode", str_buf);
-
- /*
- * Cause the DAC to:
- * Enable control port (I2C mode)
- * Remove power down
- * . MCLK divide by 1
- * . MCLK divide by 2
- */
- i2c_reg_write(I2C_DAC_ADDR, 0x05,
- DAC_REG5_I2C_MODE |
- (mclk_divide ? DAC_REG5_MCLK_DIV : 0));
-
- /*
- * Create a I2C stop condition:
- * low->high on data while clock is high.
- */
- I2C_SCL(1);
- I2C_DELAY;
- I2C_SDA(1);
- I2C_DELAY;
- I2C_TRISTATE;
-
- if (!quiet)
- printf("\n");
-#ifdef CONFIG_ETHER_LOOPBACK_TEST
- /*
- * Run the Ethernet loopback test
- */
- eth_loopback_test();
-#endif /* CONFIG_ETHER_LOOPBACK_TEST */
-
-#ifdef CONFIG_SHOW_BOOT_PROGRESS
- /*
- * Turn off the RED fail LED now that we are up and running.
- */
- status_led_set(STATUS_LED_RED, STATUS_LED_OFF);
-#endif
-
- return 0;
-}
-
-#ifdef CONFIG_SHOW_BOOT_PROGRESS
-/*
- * Show boot status: flash the LED if something goes wrong, indicating
- * that last thing that worked and thus, by implication, what is broken.
- *
- * This stores the last OK value in RAM so this will not work properly
- * before RAM is initialized. Since it is being used for indicating
- * boot status (i.e. after RAM is initialized), that is OK.
- */
-static void flash_code(uchar number, uchar modulo, uchar digits)
-{
- int j;
-
- /*
- * Recursively do upper digits.
- */
- if (digits > 1)
- flash_code(number / modulo, modulo, digits - 1);
-
- number = number % modulo;
-
- /*
- * Zero is indicated by one long flash (dash).
- */
- if (number == 0) {
- status_led_set(STATUS_LED_BOOT, STATUS_LED_ON);
- udelay(1000000);
- status_led_set(STATUS_LED_BOOT, STATUS_LED_OFF);
- udelay(200000);
- } else {
- /*
- * Non-zero is indicated by short flashes, one per count.
- */
- for (j = 0; j < number; j++) {
- status_led_set(STATUS_LED_BOOT, STATUS_LED_ON);
- udelay(100000);
- status_led_set(STATUS_LED_BOOT, STATUS_LED_OFF);
- udelay(200000);
- }
- }
- /*
- * Inter-digit pause: we've already waited 200 mSec, wait 1 sec total
- */
- udelay(700000);
-}
-
-static int last_boot_progress;
-
-void show_boot_progress(int status)
-{
- int i, j;
-
- if (status > 0) {
- last_boot_progress = status;
- } else {
- /*
- * If a specific failure code is given, flash this code
- * else just use the last success code we've seen
- */
- if (status < -1)
- last_boot_progress = -status;
-
- /*
- * Flash this code 5 times
- */
- for (j = 0; j < 5; j++) {
- /*
- * Houston, we have a problem.
- * Blink the last OK status which indicates where things failed.
- */
- status_led_set(STATUS_LED_RED, STATUS_LED_ON);
- flash_code(last_boot_progress, 5, 3);
-
- /*
- * Delay 5 seconds between repetitions,
- * with the fault LED blinking
- */
- for (i = 0; i < 5; i++) {
- status_led_set(STATUS_LED_RED,
- STATUS_LED_OFF);
- udelay(500000);
- status_led_set(STATUS_LED_RED, STATUS_LED_ON);
- udelay(500000);
- }
- }
-
- /*
- * Reset the board to retry initialization.
- */
- do_reset(NULL, 0, 0, NULL);
- }
-}
-#endif /* CONFIG_SHOW_BOOT_PROGRESS */
-
-
-/*
- * The following are used to control the SPI chip selects for the SPI command.
- */
-#if defined(CONFIG_CMD_SPI)
-
-#define SPI_ADC_CS_MASK 0x00000800
-#define SPI_DAC_CS_MASK 0x00001000
-
-static const u32 cs_mask[] = {
- SPI_ADC_CS_MASK,
- SPI_DAC_CS_MASK,
-};
-
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
- return bus == 0 && cs < sizeof(cs_mask) / sizeof(cs_mask[0]);
-}
-
-void spi_cs_activate(struct spi_slave *slave)
-{
- volatile ioport_t *iopd =
- ioport_addr((immap_t *) CONFIG_SYS_IMMR, 3 /* port D */ );
-
- iopd->pdat &= ~cs_mask[slave->cs];
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
- volatile ioport_t *iopd =
- ioport_addr((immap_t *) CONFIG_SYS_IMMR, 3 /* port D */ );
-
- iopd->pdat |= cs_mask[slave->cs];
-}
-
-#endif
-
-#endif /* CONFIG_MISC_INIT_R */
generated by cgit v1.1 at 2024-11-20 06:15:45 +0000