diff options
Diffstat (limited to 'board/pm856')
-rw-r--r-- | board/pm856/ddr.c | 5 | ||||
-rw-r--r-- | board/pm856/law.c | 10 | ||||
-rw-r--r-- | board/pm856/pm856.c | 53 | ||||
-rw-r--r-- | board/pm856/tlb.c | 22 | ||||
-rw-r--r-- | board/pm856/u-boot.lds | 1 |
5 files changed, 51 insertions, 40 deletions
diff --git a/board/pm856/ddr.c b/board/pm856/ddr.c index 45372f4..7850794 100644 --- a/board/pm856/ddr.c +++ b/board/pm856/ddr.c @@ -10,6 +10,7 @@ #include <i2c.h> #include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_ddr_dimm_params.h> static void get_spd(ddr1_spd_eeprom_t *spd, unsigned char i2c_address) @@ -40,7 +41,9 @@ fsl_ddr_get_spd(ddr1_spd_eeprom_t *ctrl_dimms_spd, } } -void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num) +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) { /* * Factors to consider for CPO: diff --git a/board/pm856/law.c b/board/pm856/law.c index d74d17a..39e8dbb 100644 --- a/board/pm856/law.c +++ b/board/pm856/law.c @@ -46,13 +46,13 @@ struct law_entry law_table[] = { #ifndef CONFIG_SPD_EEPROM - SET_LAW(CFG_DDR_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_DDR), + SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_DDR), #endif - SET_LAW(CFG_PCI1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI), + SET_LAW(CONFIG_SYS_PCI1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI), /* This is not so much the SDRAM map as it is the whole localbus map. */ - SET_LAW(CFG_LBC_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_LBC), - SET_LAW(CFG_PCI1_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI), - SET_LAW(CFG_RIO_MEM_BASE, LAWAR_SIZE_512M, LAW_TRGT_IF_RIO), + SET_LAW(CONFIG_SYS_LBC_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_PCI1_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI), + SET_LAW(CONFIG_SYS_RIO_MEM_BASE, LAWAR_SIZE_512M, LAW_TRGT_IF_RIO), }; int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/pm856/pm856.c b/board/pm856/pm856.c index bd4c065..932f112 100644 --- a/board/pm856/pm856.c +++ b/board/pm856/pm856.c @@ -34,6 +34,7 @@ #include <ioports.h> #include <spd_sdram.h> #include <miiphy.h> +#include <netdev.h> #if defined(CONFIG_DDR_ECC) extern void ddr_enable_ecc(unsigned int dram_size); @@ -237,7 +238,7 @@ initdram(int board_type) #if defined(CONFIG_DDR_DLL) { - volatile ccsr_gur_t *gur = (void *)(CFG_MPC85xx_GUTS_ADDR); + volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); int i,x; x = 10; @@ -288,8 +289,8 @@ initdram(int board_type) void local_bus_init(void) { - volatile ccsr_gur_t *gur = (void *)(CFG_MPC85xx_GUTS_ADDR); - volatile ccsr_lbc_t *lbc = (void *)(CFG_MPC85xx_LBC_ADDR); + volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR); uint clkdiv; uint lbc_hz; @@ -299,8 +300,8 @@ local_bus_init(void) * Errata LBC11. * Fix Local Bus clock glitch when DLL is enabled. * - * If localbus freq is < 66Mhz, DLL bypass mode must be used. - * If localbus freq is > 133Mhz, DLL can be safely enabled. + * If localbus freq is < 66MHz, DLL bypass mode must be used. + * If localbus freq is > 133MHz, DLL can be safely enabled. * Between 66 and 133, the DLL is enabled with an override workaround. */ @@ -309,10 +310,10 @@ local_bus_init(void) lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; if (lbc_hz < 66) { - lbc->lcrr = CFG_LBC_LCRR | 0x80000000; /* DLL Bypass */ + lbc->lcrr = CONFIG_SYS_LBC_LCRR | 0x80000000; /* DLL Bypass */ } else if (lbc_hz >= 133) { - lbc->lcrr = CFG_LBC_LCRR & (~0x80000000); /* DLL Enabled */ + lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~0x80000000); /* DLL Enabled */ } else { /* @@ -327,7 +328,7 @@ local_bus_init(void) lbc->lcrr = 0x10000004; } - lbc->lcrr = CFG_LBC_LCRR & (~0x80000000);/* DLL Enabled */ + lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~0x80000000);/* DLL Enabled */ udelay(200); /* @@ -340,11 +341,11 @@ local_bus_init(void) } } -#if defined(CFG_DRAM_TEST) +#if defined(CONFIG_SYS_DRAM_TEST) int testdram (void) { - uint *pstart = (uint *) CFG_MEMTEST_START; - uint *pend = (uint *) CFG_MEMTEST_END; + uint *pstart = (uint *) CONFIG_SYS_MEMTEST_START; + uint *pend = (uint *) CONFIG_SYS_MEMTEST_END; uint *p; printf("SDRAM test phase 1:\n"); @@ -381,15 +382,15 @@ int testdram (void) ************************************************************************/ long int fixed_sdram (void) { - #ifndef CFG_RAMBOOT - volatile ccsr_ddr_t *ddr= (void *)(CFG_MPC85xx_DDR_ADDR); - - ddr->cs0_bnds = CFG_DDR_CS0_BNDS; - ddr->cs0_config = CFG_DDR_CS0_CONFIG; - ddr->timing_cfg_1 = CFG_DDR_TIMING_1; - ddr->timing_cfg_2 = CFG_DDR_TIMING_2; - ddr->sdram_mode = CFG_DDR_MODE; - ddr->sdram_interval = CFG_DDR_INTERVAL; + #ifndef CONFIG_SYS_RAMBOOT + volatile ccsr_ddr_t *ddr= (void *)(CONFIG_SYS_MPC85xx_DDR_ADDR); + + ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS; + ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG; + ddr->timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1; + ddr->timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2; + ddr->sdram_mode = CONFIG_SYS_DDR_MODE; + ddr->sdram_interval = CONFIG_SYS_DDR_INTERVAL; #if defined (CONFIG_DDR_ECC) ddr->err_disable = 0x0000000D; ddr->err_sbe = 0x00ff0000; @@ -398,14 +399,14 @@ long int fixed_sdram (void) udelay(500); #if defined (CONFIG_DDR_ECC) /* Enable ECC checking */ - ddr->sdram_cfg = (CFG_DDR_CONTROL | 0x20000000); + ddr->sdram_cfg = (CONFIG_SYS_DDR_CONTROL | 0x20000000); #else - ddr->sdram_cfg = CFG_DDR_CONTROL; + ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL; #endif asm("sync; isync; msync"); udelay(500); #endif - return CFG_SDRAM_SIZE * 1024 * 1024; + return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; } #endif /* !defined(CONFIG_SPD_EEPROM) */ @@ -444,3 +445,9 @@ pci_init_board(void) pci_mpc85xx_init(&hose); #endif /* CONFIG_PCI */ } + +int board_eth_init(bd_t *bis) +{ + cpu_eth_init(bis); /* Intialize TSECs first */ + return pci_eth_init(bis); +} diff --git a/board/pm856/tlb.c b/board/pm856/tlb.c index a7f3813..5e74e2d 100644 --- a/board/pm856/tlb.c +++ b/board/pm856/tlb.c @@ -28,16 +28,16 @@ struct fsl_e_tlb_entry tlb_table[] = { /* TLB 0 - for temp stack in cache */ - SET_TLB_ENTRY(0, CFG_INIT_RAM_ADDR, CFG_INIT_RAM_ADDR, + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, MAS3_SX|MAS3_SW|MAS3_SR, 0, 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CFG_INIT_RAM_ADDR + 4 * 1024 , CFG_INIT_RAM_ADDR + 4 * 1024, + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, MAS3_SX|MAS3_SW|MAS3_SR, 0, 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CFG_INIT_RAM_ADDR + 8 * 1024 , CFG_INIT_RAM_ADDR + 8 * 1024, + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, MAS3_SX|MAS3_SW|MAS3_SR, 0, 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CFG_INIT_RAM_ADDR + 12 * 1024 , CFG_INIT_RAM_ADDR + 12 * 1024, + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, MAS3_SX|MAS3_SW|MAS3_SR, 0, 0, 0, BOOKE_PAGESZ_4K, 0), @@ -54,7 +54,7 @@ struct fsl_e_tlb_entry tlb_table[] = { * TLB 1: 256M Non-cacheable, guarded * 0x80000000 256M PCI1 MEM First half */ - SET_TLB_ENTRY(1, CFG_PCI1_MEM_PHYS, CFG_PCI1_MEM_PHYS, + SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_MEM_PHYS, CONFIG_SYS_PCI1_MEM_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 1, BOOKE_PAGESZ_256M, 1), @@ -62,7 +62,7 @@ struct fsl_e_tlb_entry tlb_table[] = { * TLB 2: 256M Non-cacheable, guarded * 0x90000000 256M PCI1 MEM Second half */ - SET_TLB_ENTRY(1, CFG_PCI1_MEM_PHYS + 0x10000000, CFG_PCI1_MEM_PHYS + 0x10000000, + SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_MEM_PHYS + 0x10000000, CONFIG_SYS_PCI1_MEM_PHYS + 0x10000000, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 2, BOOKE_PAGESZ_256M, 1), @@ -70,7 +70,7 @@ struct fsl_e_tlb_entry tlb_table[] = { * TLB 3: 256M Non-cacheable, guarded * 0xc0000000 256M Rapid IO MEM First half */ - SET_TLB_ENTRY(1, CFG_RIO_MEM_BASE, CFG_RIO_MEM_BASE, + SET_TLB_ENTRY(1, CONFIG_SYS_RIO_MEM_BASE, CONFIG_SYS_RIO_MEM_BASE, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 3, BOOKE_PAGESZ_256M, 1), @@ -78,7 +78,7 @@ struct fsl_e_tlb_entry tlb_table[] = { * TLB 4: 256M Non-cacheable, guarded * 0xd0000000 256M Rapid IO MEM Second half */ - SET_TLB_ENTRY(1, CFG_RIO_MEM_BASE + 0x10000000, CFG_RIO_MEM_BASE + 0x10000000, + SET_TLB_ENTRY(1, CONFIG_SYS_RIO_MEM_BASE + 0x10000000, CONFIG_SYS_RIO_MEM_BASE + 0x10000000, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 4, BOOKE_PAGESZ_256M, 1), @@ -87,7 +87,7 @@ struct fsl_e_tlb_entry tlb_table[] = { * 0xe000_0000 1M CCSRBAR * 0xe200_0000 16M PCI1 IO */ - SET_TLB_ENTRY(1, CFG_CCSRBAR, CFG_CCSRBAR_PHYS, + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 5, BOOKE_PAGESZ_64M, 1), @@ -95,7 +95,7 @@ struct fsl_e_tlb_entry tlb_table[] = { * TLB 6: 64M Cacheable, non-guarded * 0xf000_0000 64M LBC SDRAM */ - SET_TLB_ENTRY(1, CFG_LBC_SDRAM_BASE, CFG_LBC_SDRAM_BASE, + SET_TLB_ENTRY(1, CONFIG_SYS_LBC_SDRAM_BASE, CONFIG_SYS_LBC_SDRAM_BASE, MAS3_SX|MAS3_SW|MAS3_SR, 0, 0, 6, BOOKE_PAGESZ_64M, 1), @@ -108,7 +108,7 @@ struct fsl_e_tlb_entry tlb_table[] = { * Likely it needs to be increased by two for these entries. */ - SET_TLB_ENTRY(1, CFG_DDR_SDRAM_BASE, CFG_DDR_SDRAM_BASE, + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, MAS3_SX|MAS3_SW|MAS3_SR, 0, 0, 7, BOOKE_PAGESZ_256M, 1), #endif diff --git a/board/pm856/u-boot.lds b/board/pm856/u-boot.lds index 01727d1..e9c6a12 100644 --- a/board/pm856/u-boot.lds +++ b/board/pm856/u-boot.lds @@ -141,6 +141,7 @@ SECTIONS *(.dynbss) *(.bss) *(COMMON) + . = ALIGN(4); } _end = . ; PROVIDE (end = .); |