diff options
Diffstat (limited to 'board/netstar/crcek.S')
| -rw-r--r-- | board/netstar/crcek.S | 80 |
1 files changed, 72 insertions, 8 deletions
diff --git a/board/netstar/crcek.S b/board/netstar/crcek.S index 6ca4d11..a74abf9 100644 --- a/board/netstar/crcek.S +++ b/board/netstar/crcek.S @@ -13,6 +13,7 @@ * u32 - crc32 */ +#include <config.h> #include "crcek.h" /** @@ -39,7 +40,7 @@ .macro crcuj, offset, size mov r0, #0 ldr r1, \offset - ldr r2, [r1] + ldr r2, [r1], #4 cmp r2, r0 @ no data, no problem beq 2f tst r2, #3 @ unaligned size @@ -47,7 +48,6 @@ ldr r3, \size cmp r2, r3 @ bogus size bhi 2f - add r1, r1, #4 do_crc32 ldr r1, [r1] 2: @@ -55,16 +55,71 @@ .endm .macro wait, reg - mov \reg, #0x1000 + mov \reg, #0x100000 3: subs \reg, \reg, #0x1 bne 3b - .endm + .text .globl crcek crcek: - b crc2_bad + /* Enable I-cache */ + mrc p15, 0, r1, c0, c0, 0 @ read C15 ID register + mrc p15, 0, r1, c0, c0, 1 @ read C15 Cache information register + mrc p15, 0, r1, c1, c0, 0 @ read C15 Control register + orr r1, r1, #0x1000 @ enable I-cache, map interrupt vector 0xffff0000 + mcr p15, 0, r1, c1, c0, 0 @ write C15 Control register + mov r1, #0x00 + mcr p15, 0, r1, c7, c5, 0 @ Flush I-cache + nop + nop + nop + nop + + /* Setup clocking mode */ + ldr r0, MPU_CLKM_BASE @ base of CLOCK unit + ldrh r1, [r0, #0x18] @ ARM_SYST - get reset status + bic r1, r1, #(7 << 11) @ clear clock select + orr r1, r1, #(2 << 11) @ set synchronous scalable + mov r2, #0 +loop: + cmp r2, #1 @ this loop will wait for at least 100 cycles + streqh r1, [r0, #0x18] @ before issuing next request from MPU + add r2, r2, #1 @ on the 1st run code is loaded into I-cache + cmp r2, #16 @ and second run will set clocking mode + bne loop + nop + + /* Setup clock dividers */ + ldr r1, CKCTL_VAL + orr r1, r1, #0x2000 @ enable DSP clock + strh r1, [r0] @ setup clock divisors + + /* Setup DPLL to generate requested freq */ + ldr r0, DPLL1_BASE @ base of DPLL1 register + mov r1, #0x0010 @ set PLL_ENABLE + orr r1, r1, #0x2000 @ set IOB to new locking + orr r1, r1, #(OMAP5910_DPLL_MUL << 7) @ setup multiplier CLKREF + orr r1, r1, #(OMAP5910_DPLL_DIV << 5) @ setup divider CLKREF + strh r1, [r0] @ write + +locking: + ldrh r1, [r0] @ get DPLL value + tst r1, #0x01 + beq locking @ while LOCK not set + + /* Enable clock */ + ldr r0, MPU_CLKM_BASE @ base of CLOCK unit + mov r1, #(1 << 10) @ disable idle mode do not check + @ nWAKEUP pin, other remain active + strh r1, [r0, #0x04] + ldr r1, EN_CLK_VAL + strh r1, [r0, #0x08] + mov r1, #0x003f @ FLASH.RP not enabled in idle and + strh r1, [r0, #0x0c] @ max delayed ( 32 x CLKIN ) + + mov r6, #0 crcuj _LOADER1_OFFSET, _LOADER_SIZE bne crc1_bad @@ -76,9 +131,8 @@ crc1_bad: crc2_bad: ldr r3, _LOADER1_OFFSET ldr r4, _LOADER2_OFFSET - b boot_2nd - tst r6, #3 - beq one_is_bad @ one of them (or both) has bad crc + teq r6, #3 + bne one_is_bad @ one of them (or both) has bad crc ldr r1, [r3, #4] ldr r2, [r4, #4] cmp r1, r2 @ boot 2nd loader if versions differ @@ -90,6 +144,7 @@ one_is_bad: tst r6, #2 bne boot_2nd @ We are doomed, so let user know. +hell: ldr r0, GPIO_BASE @ configure GPIO pins ldr r1, GPIO_DIRECTION strh r1, [r0, #0x08] @@ -171,6 +226,15 @@ CRC32_TABLE: GPIO_BASE: .word 0xfffce000 +MPU_CLKM_BASE: + .word 0xfffece00 +DPLL1_BASE: + .word 0xfffecf00 + +CKCTL_VAL: + .word OMAP5910_ARM_CKCTL +EN_CLK_VAL: + .word OMAP5910_ARM_EN_CLK GPIO_DIRECTION: .word 0x0000ffe7 |