diff options
Diffstat (limited to 'board/mpl/pip405/pip405.h')
| -rw-r--r-- | board/mpl/pip405/pip405.h | 116 |
1 files changed, 32 insertions, 84 deletions
diff --git a/board/mpl/pip405/pip405.h b/board/mpl/pip405/pip405.h index c2411a3..b41c5bb 100644 --- a/board/mpl/pip405/pip405.h +++ b/board/mpl/pip405/pip405.h @@ -25,6 +25,7 @@ * Global routines used for PIP405 *****************************************************************************/ +#ifndef __ASSEMBLY__ extern int mem_test(unsigned long start, unsigned long ramsize,int mode); @@ -35,13 +36,13 @@ void user_led1(unsigned char on); #define PLD_BASE_ADDRESS CFG_ISA_IO_BASE_ADDRESS + 0x800 -#define PLD_PART_REG PLD_BASE_ADDRESS + 0 -#define PLD_VERS_REG PLD_BASE_ADDRESS + 1 +#define PLD_PART_REG PLD_BASE_ADDRESS + 0 +#define PLD_VERS_REG PLD_BASE_ADDRESS + 1 #define PLD_BOARD_CFG_REG PLD_BASE_ADDRESS + 2 #define PLD_LED_USER_REG PLD_BASE_ADDRESS + 3 #define PLD_SYS_MAN_REG PLD_BASE_ADDRESS + 4 #define PLD_FLASH_COM_REG PLD_BASE_ADDRESS + 5 -#define PLD_CAN_REG PLD_BASE_ADDRESS + 6 +#define PLD_CAN_REG PLD_BASE_ADDRESS + 6 #define PLD_SER_PWR_REG PLD_BASE_ADDRESS + 7 #define PLD_COM_PWR_REG PLD_BASE_ADDRESS + 8 #define PLD_NIC_VGA_REG PLD_BASE_ADDRESS + 9 @@ -50,86 +51,32 @@ void user_led1(unsigned char on); #define PIIX4_VENDOR_ID 0x8086 #define PIIX4_IDE_DEV_ID 0x7111 +#endif /* timings */ -/* PLD (CS7) */ -#define PLD_BME 0 /* Burst disable */ -#define PLD_TWE 5 /* 5 * 30ns 120ns Waitstates (access=TWT+1+TH) */ -#define PLD_CSN 1 /* Chipselect is driven inactive for 1 Cycle BTW transfers */ -#define PLD_OEN 1 /* Cycles from CS low to OE low */ -#define PLD_WBN 1 /* Cycles from CS low to WE low */ -#define PLD_WBF 1 /* Cycles from WE high to CS high */ -#define PLD_TH 2 /* Number of hold cycles after transfer */ -#define PLD_RE 0 /* Ready disabled */ -#define PLD_SOR 1 /* Sample on Ready disabled */ -#define PLD_BEM 0 /* Byte Write only active on Write cycles */ -#define PLD_PEN 0 /* Parity disable */ -#define PLD_AP ((PLD_BME << 31) + (PLD_TWE << 23) + (PLD_CSN << 18) + (PLD_OEN << 16) + (PLD_WBN << 14) + \ - (PLD_WBF << 12) + (PLD_TH << 9) + (PLD_RE << 8) + (PLD_SOR << 7) + (PLD_BEM << 6) + (PLD_PEN << 5)) - -/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */ -#define PLD_BS 0 /* 1 MByte */ -/* Usage: 0=disabled, 1=Read only, 2=Write Only, 3=R/W */ -#define PLD_BU 3 /* R/W */ -/* Bus width: 0=8Bit, 1=16Bit, 2=32Bit, 3=Reserved */ -#define PLD_BW 0 /* 16Bit */ -#define PLD_CR ((PER_PLD_ADDR & 0xfff00000) + (PLD_BS << 17) + (PLD_BU << 15) + (PLD_BW << 13)) - -/* timings */ - -#define PER_BOARD_ADDR (PER_UART1_ADDR+(1024*1024)) -/* Dummy CS to get the board revision */ -#define BOARD_BME 0 /* Burst disable */ -#define BOARD_TWE 255 /* 255 * 30ns 120ns Waitstates (access=TWT+1+TH) */ -#define BOARD_CSN 1 /* Chipselect is driven inactive for 1 Cycle BTW transfers */ -#define BOARD_OEN 1 /* Cycles from CS low to OE low */ -#define BOARD_WBN 1 /* Cycles from CS low to WE low */ -#define BOARD_WBF 1 /* Cycles from WE high to CS high */ -#define BOARD_TH 2 /* Number of hold cycles after transfer */ -#define BOARD_RE 0 /* Ready disabled */ -#define BOARD_SOR 1 /* Sample on Ready disabled */ -#define BOARD_BEM 0 /* Byte Write only active on Write cycles */ -#define BOARD_PEN 0 /* Parity disable */ -#define BOARD_AP ((BOARD_BME << 31) + (BOARD_TWE << 23) + (BOARD_CSN << 18) + (BOARD_OEN << 16) + (BOARD_WBN << 14) + \ - (BOARD_WBF << 12) + (BOARD_TH << 9) + (BOARD_RE << 8) + (BOARD_SOR << 7) + (BOARD_BEM << 6) + (BOARD_PEN << 5)) +/* CS Config register (CS7) */ +#define CONFIG_PORT_BME 0 /* Burst disable */ +#define CONFIG_PORT_TWE 255 /* 255 * 30ns 120ns Waitstates (access=TWT+1+TH) */ +#define CONFIG_PORT_CSN 1 /* Chipselect is driven inactive for 1 Cycle BTW transfers */ +#define CONFIG_PORT_OEN 1 /* Cycles from CS low to OE low */ +#define CONFIG_PORT_WBN 1 /* Cycles from CS low to WE low */ +#define CONFIG_PORT_WBF 1 /* Cycles from WE high to CS high */ +#define CONFIG_PORT_TH 2 /* Number of hold cycles after transfer */ +#define CONFIG_PORT_RE 0 /* Ready disabled */ +#define CONFIG_PORT_SOR 1 /* Sample on Ready disabled */ +#define CONFIG_PORT_BEM 0 /* Byte Write only active on Write cycles */ +#define CONFIG_PORT_PEN 0 /* Parity disable */ +#define CONFIG_PORT_AP ((CONFIG_PORT_BME << 31) + (CONFIG_PORT_TWE << 23) + (CONFIG_PORT_CSN << 18) + (CONFIG_PORT_OEN << 16) + (CONFIG_PORT_WBN << 14) + \ + (CONFIG_PORT_WBF << 12) + (CONFIG_PORT_TH << 9) + (CONFIG_PORT_RE << 8) + (CONFIG_PORT_SOR << 7) + (CONFIG_PORT_BEM << 6) + (CONFIG_PORT_PEN << 5)) /* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */ -#define BOARD_BS 0 /* 1 MByte */ +#define CONFIG_PORT_BS 0 /* 1 MByte */ /* Usage: 0=disabled, 1=Read only, 2=Write Only, 3=R/W */ -#define BOARD_BU 3 /* R/W */ +#define CONFIG_PORT_BU 3 /* R/W */ /* Bus width: 0=8Bit, 1=16Bit, 2=32Bit, 3=Reserved */ -#define BOARD_BW 0 /* 16Bit */ -#define BOARD_CR ((PER_BOARD_ADDR & 0xfff00000) + (BOARD_BS << 17) + (BOARD_BU << 15) + (BOARD_BW << 13)) - - -/* UART0 CS2 */ -#define UART0_BME 0 /* Burst disable */ -#define UART0_TWE 7 /* 7 * 30ns 210ns Waitstates (access=TWT+1+TH) */ -#define UART0_CSN 1 /* Chipselect is driven inactive for 1 Cycle BTW transfers */ -#define UART0_OEN 1 /* Cycles from CS low to OE low */ -#define UART0_WBN 1 /* Cycles from CS low to WE low */ -#define UART0_WBF 1 /* Cycles from WE high to CS high */ -#define UART0_TH 2 /* Number of hold cycles after transfer */ -#define UART0_RE 0 /* Ready disabled */ -#define UART0_SOR 1 /* Sample on Ready disabled */ -#define UART0_BEM 0 /* Byte Write only active on Write cycles */ -#define UART0_PEN 0 /* Parity disable */ -#define UART0_AP ((UART0_BME << 31) + (UART0_TWE << 23) + (UART0_CSN << 18) + (UART0_OEN << 16) + (UART0_WBN << 14) + \ - (UART0_WBF << 12) + (UART0_TH << 9) + (UART0_RE << 8) + (UART0_SOR << 7) + (UART0_BEM << 6) + (UART0_PEN << 5)) - -/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */ -#define UART0_BS 0 /* 1 MByte */ -/* Usage: 0=disabled, 1=Read only, 2=Write Only, 3=R/W */ -#define UART0_BU 3 /* R/W */ -/* Bus width: 0=8Bit, 1=16Bit, 2=32Bit, 3=Reserved */ -#define UART0_BW 0 /* 8Bit */ -#define UART0_CR ((PER_UART0_ADDR & 0xfff00000) + (UART0_BS << 17) + (UART0_BU << 15) + (UART0_BW << 13)) - -/* UART1 CS3 */ -#define UART1_AP UART0_AP /* same timing as UART0 */ -#define UART1_CR ((PER_UART1_ADDR & 0xfff00000) + (UART0_BS << 17) + (UART0_BU << 15) + (UART0_BW << 13)) - +#define CONFIG_PORT_BW 0 /* 16Bit */ +#define CONFIG_PORT_CR ((CONFIG_PORT_ADDR & 0xfff00000) + (CONFIG_PORT_BS << 17) + (CONFIG_PORT_BU << 15) + (CONFIG_PORT_BW << 13)) /* Flash CS0 or CS 1 */ /* 0x7F8FFE80 slowest timing at all... */ @@ -149,19 +96,19 @@ void user_led1(unsigned char on); #define FLASH_PEN 0 /* Parity disable */ /* Access Parameter Register for non Boot */ #define FLASH_AP ((FLASH_BME << 31) + (FLASH_TWE << 23) + (FLASH_CSN << 18) + (FLASH_OEN << 16) + (FLASH_WBN << 14) + \ - (FLASH_WBF << 12) + (FLASH_TH << 9) + (FLASH_RE << 8) + (FLASH_SOR << 7) + (FLASH_BEM << 6) + (FLASH_PEN << 5)) + (FLASH_WBF << 12) + (FLASH_TH << 9) + (FLASH_RE << 8) + (FLASH_SOR << 7) + (FLASH_BEM << 6) + (FLASH_PEN << 5)) /* Access Parameter Register for Boot */ #define FLASH_AP_B ((FLASH_BME_B << 31) + (FLASH_FWT_B << 26) + (FLASH_BWT_B << 23) + (FLASH_CSN << 18) + (FLASH_OEN << 16) + (FLASH_WBN << 14) + \ - (FLASH_WBF << 12) + (FLASH_TH << 9) + (FLASH_RE << 8) + (FLASH_SOR << 7) + (FLASH_BEM << 6) + (FLASH_PEN << 5)) + (FLASH_WBF << 12) + (FLASH_TH << 9) + (FLASH_RE << 8) + (FLASH_SOR << 7) + (FLASH_BEM << 6) + (FLASH_PEN << 5)) /* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */ -#define FLASH_BS 2 /* 4 MByte */ +#define FLASH_BS FLASH_SIZE_PRELIM /* 4 MByte */ /* Usage: 0=disabled, 1=Read only, 2=Write Only, 3=R/W */ #define FLASH_BU 3 /* R/W */ /* Bus width: 0=8Bit, 1=16Bit, 2=32Bit, 3=Reserved */ #define FLASH_BW 1 /* 16Bit */ /* CR register for Boot */ -#define FLASH_CR_B ((FLASH_BASE0_PRELIM & 0xfff00000) + (FLASH_BS << 17) + (FLASH_BU << 15) + (FLASH_BW << 13)) +#define FLASH_CR_B ((FLASH_BASE_PRELIM & 0xfff00000) + (FLASH_BS << 17) + (FLASH_BU << 15) + (FLASH_BW << 13)) /* CR register for non Boot */ #define FLASH_CR ((MULTI_PURPOSE_SOCKET_ADDR & 0xfff00000) + (FLASH_BS << 17) + (FLASH_BU << 15) + (FLASH_BW << 13)) @@ -183,18 +130,19 @@ void user_led1(unsigned char on); #define MPS_PEN 0 /* Parity disable */ /* Access Parameter Register for non Boot */ #define MPS_AP ((MPS_BME << 31) + (MPS_TWE << 23) + (MPS_CSN << 18) + (MPS_OEN << 16) + (MPS_WBN << 14) + \ - (MPS_WBF << 12) + (MPS_TH << 9) + (MPS_RE << 8) + (MPS_SOR << 7) + (MPS_BEM << 6) + (MPS_PEN << 5)) + (MPS_WBF << 12) + (MPS_TH << 9) + (MPS_RE << 8) + (MPS_SOR << 7) + (MPS_BEM << 6) + (MPS_PEN << 5)) /* Access Parameter Register for Boot */ -#define MPS_AP_B ((MPS_BME_B << 31) + (MPS_FWT_B << 26) + (MPS_BWT_B << 23) + (MPS_CSN << 18) + (MPS_OEN << 16) + (MPS_WBN << 14) + \ - (MPS_WBF << 12) + (MPS_TH << 9) + (MPS_RE << 8) + (MPS_SOR << 7) + (MPS_BEM << 6) + (MPS_PEN << 5)) +#define MPS_AP_B ((MPS_BME_B << 31) + (MPS_FWT_B << 26) + (MPS_BWT_B << 23) + (MPS_CSN << 18) + (MPS_OEN << 16) + (MPS_WBN << 14) + \ + (MPS_WBF << 12) + (MPS_TH << 9) + (MPS_RE << 8) + (MPS_SOR << 7) + (MPS_BEM << 6) + (MPS_PEN << 5)) /* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */ #define MPS_BS 2 /* 4 MByte */ +#define MPS_BS_B FLASH_SIZE_PRELIM /* 1 MByte */ /* Usage: 0=disabled, 1=Read only, 2=Write Only, 3=R/W */ #define MPS_BU 3 /* R/W */ /* Bus width: 0=8Bit, 1=16Bit, 2=32Bit, 3=Reserved */ #define MPS_BW 0 /* 8Bit */ /* CR register for Boot */ -#define MPS_CR_B ((FLASH_BASE0_PRELIM & 0xfff00000) + (MPS_BS << 17) + (MPS_BU << 15) + (MPS_BW << 13)) +#define MPS_CR_B ((FLASH_BASE_PRELIM & 0xfff00000) + (MPS_BS << 17) + (MPS_BU << 15) + (MPS_BW << 13)) /* CR register for non Boot */ #define MPS_CR ((MULTI_PURPOSE_SOCKET_ADDR & 0xfff00000) + (MPS_BS << 17) + (MPS_BU << 15) + (MPS_BW << 13)) |