diff options
Diffstat (limited to 'board/mpc7448hpc2/tsi108_init.c')
| -rw-r--r-- | board/mpc7448hpc2/tsi108_init.c | 24 |
1 files changed, 12 insertions, 12 deletions
diff --git a/board/mpc7448hpc2/tsi108_init.c b/board/mpc7448hpc2/tsi108_init.c index e3b09cf..8a7efef 100644 --- a/board/mpc7448hpc2/tsi108_init.c +++ b/board/mpc7448hpc2/tsi108_init.c @@ -179,7 +179,7 @@ int board_early_init_r (void) ulong temp, i; ulong reg_val; volatile ulong *reg_ptr; - + reg_ptr = (ulong *) (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + 0x900); @@ -300,7 +300,7 @@ int board_early_init_r (void) out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_CTRL1, 0x7C0F2000); __asm__ __volatile__ ("sync"); - + /* * Set new value for PB_OCN_BAR1: switch from BOOT to LUT mode. * value for PB_OCN_BAR1: (BA-0xE000_0000 + size 512MB + ENable) @@ -312,7 +312,7 @@ int board_early_init_r (void) /* Make sure that OCN_BAR2 decoder is set (to allow following * immediate read from SDRAM) */ - + temp = in32(CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR1); __asm__ __volatile__ ("sync"); @@ -327,11 +327,11 @@ int board_early_init_r (void) * and enable all HLP banks and not just HLP 0 as is being done for * Taiga Rev. 2. */ - + env_init (); #ifndef DISABLE_PBM - + /* * For IBM processors we have to set Address-Only commands generated * by PBM that are different from ones set after reset. @@ -475,10 +475,10 @@ int board_early_init_r (void) for (i = 0; i < 32; i++) { *reg_ptr++ = reg_val; /* P2O_BAR3_LUTx */ - + /* P2O_BAR3_LUT_UPPERx : Set data swapping mode for PBM (byte swapping) */ - *reg_ptr++ = 0; - + *reg_ptr++ = 0; + /* offset = 16MB, address translation is enabled to allow byte swapping */ reg_val += 0x01000000; } @@ -507,7 +507,7 @@ int board_early_init_r (void) #endif /* !DISABLE_PBM */ -#ifdef ENABLE_PCI_CSR_BAR +#ifdef ENABLE_PCI_CSR_BAR /* open if required access to Tsi108 CSRs from the PCI/X bus */ /* enable BAR0 on the PCI/X bus */ reg_val = in32(CFG_TSI108_CSR_BASE + @@ -528,7 +528,7 @@ int board_early_init_r (void) /* * Finally enable PCI/X Bus Master and Memory Space access */ - + reg_val = in32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_CSR); reg_val |= 0x06; out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_CSR, reg_val); @@ -555,7 +555,7 @@ int board_early_init_r (void) * Ensure that Machine Check exception is enabled * We need it to support PCI Bus probing (configuration reads) */ - + reg_val = mfmsr (); mtmsr(reg_val | MSR_ME); @@ -631,7 +631,7 @@ int misc_init_r (void) * thing done with regards to enabling diabling the cache. * So this seems like a good place to print all this information */ - + printf ("CACHE: "); switch (get_cpu_type()) { case CPU_7447A: |