diff options
Diffstat (limited to 'board/mousse/README')
| -rw-r--r-- | board/mousse/README | 346 |
1 files changed, 0 insertions, 346 deletions
diff --git a/board/mousse/README b/board/mousse/README deleted file mode 100644 index d5dda7a..0000000 --- a/board/mousse/README +++ /dev/null @@ -1,346 +0,0 @@ - -U-Boot for MOUSSE/MPC8240 (KAHLUA) ----------------------------------- -James Dougherty (jfd@broadcom.com), 09/10/01 - -The Broadcom/Vooha Mousse board is a 3U Compact PCI system board -which uses the MPC8240, a 64MB SDRAM SIMM, and has onboard -DEC 21143, NS16550 UART, an SGS M48T59Y TOD, and 4MB FLASH. -See also: http://www.vooha.com/ - -* NVRAM setenv/printenv/savenv supported. -* Date Command -* Serial Console support -* Network support -* FLASH of kernel images is supported. -* FLASH of U-Boot to onboard and PLCC boot region. -* Kernel command line options from NVRAM is supported. -* IP PNP options supported. - -U-Boot Loading... - - -U-Boot 1.0.5 (Sep 10 2001 - 00:22:25) - -CPU: MPC8240 Revision 1.1 at 198 MHz: 16 kB I-Cache 16 kB D-Cache -Board: MOUSSE MPC8240/KAHLUA - CHRP (MAP B) -Built: Sep 10 2001 at 01:01:50 -MPLD: Revision 127 -Local Bus: 33 MHz -RTC: M48T589 TOD/NVRAM (8176) bytes - Current date/time: 9/10/2001 0:18:52 -DRAM: 64 MB -FLASH: 1.960 MB -PCI: scanning bus0 ... - bus dev fn venID devID class rev MBAR0 MBAR1 IPIN ILINE - 00 00 00 1057 0003 060000 11 00000008 00000000 01 00 - 00 0d 00 1011 0019 020000 41 80000001 80000000 01 01 - 00 0e 00 105a 4d38 018000 01 a0000001 a0001001 01 03 -In: serial -Out: serial -Err: serial - -Hit any key to stop autoboot: 0 -=> - -I. Root FileSystem/IP Configuration - -bootcmd=tftp 100000 vmlinux.img;bootm -bootdelay=3 -baudrate=9600 -ipaddr=<IP ADDRESS> -netmask=<NETMASK> -hostname=<NAME> -serverip=<NFS SERVER IP ADDRESS> -ethaddr=00:00:10:20:30:44 -nfsroot=<NFS SERVER IP ADDRESS>:/boot/root-fs -gateway=<IP ADDRESS> -root=/dev/nfs -stdin=serial -stdout=serial -stderr=serial - -NVRAM environment variables. - -use the command: - -setenv <attribute> <value> - -type "saveenv" to write to NVRAM. - - -II. To boot from a hard drive: - -setenv root /dev/hda1 - - -III. IP options which configure the network: - -ipaddr=<IP ADDRESS OF MACHINE> -netmask=<NETMASK> -hostname=mousse -ethaddr=00:00:10:20:30:44 -gateway=<IP ADDRESS OF GATEWAY/ROUTER> - - -IV. IP Options which configure NFS Root/Boot Support - -root=/dev/nfs -serverip=<NFS SERVER IP ADDRESS> -nfsroot=<NFS SERVER IP ADDRESS>:/boot/root-fs - -V. U-Boot Image Support - -The U-Boot boot loader assumes that after you build -your kernel (vmlinux), you will create a U-Boot image -using the following commands or script: - -#!/bin/csh -/bin/touch vmlinux.img -/bin/rm vmlinux.img -set path=($TOOLBASE/bin $path) -set path=($U_BOOT/tools $path) -powerpc-linux-objcopy -S -O binary vmlinux vmlinux.bin -gzip -vf vmlinux.bin -mkimage -A ppc -O linux -T kernel -C gzip -a 0 -e 0 -n vmlinux.bin.gz -d vmlinux.bin.gz vmlinux.img -ls -l vmlinux.img - - -VI. ONBOARD FLASH Support - -FLASH support is provided for the onboard FLASH chip Bootrom area. -U-Boot is loaded into either the ROM boot region of the FLASH chip, -after first being boot-strapped from a pre-progammed AMD29F040 PLCC -bootrom. The PLCC needs to be programmed with a ROM burner using -AMD 29F040 ROM parts and the u-boot.bin or u-boot.hex (S-Record) -images. - -The PLCC overlays this same region of flash as the onboard FLASH, -the jumper J100 is a chip-select for which flash chip you want to -progam. When jumper J100 is connected to pins 2-3, you boot from -PLCC FLASH. - -To bringup a system, simply flash a flash an AMD29F040 PLCC -bootrom, and put this in the PLCC socket. Move jumper J100 to -pins 2-3 and boot from the PLCC. - - -Now, while the system is running, move Jumper J100 to -pins 1-2 and follow the procedure below to FLASH a bootrom -(u-boot.bin) image into the onboard bootrom region (AMD29LV160DB): - -tftp 100000 u-boot.bin -protect off FFF00000 FFF7FFFF -erase FFF00000 FFF7FFFF -cp.b 100000 FFF00000 \${filesize}\ - - -Here is an example: - -=>tftp 100000 u-boot.bin -eth_halt -eth0: DC21143 Ethernet adapter(bus=0, device=13, func=0) -DEC Ethernet iobase=0x80000000 -ARP broadcast 1 -Filename 'u-boot.bin'. -Load address: 0x100000 -Loading: ######################### -done -Bytes transferred = 123220 (1e154 hex) -eth_halt -=>protect off FFF00000 FFF7FFFF -Un-Protected 8 sectors -=>erase FFF00000 FFF7FFFF -Erase Flash from 0xfff00000 to 0xfff7ffff -Erase FLASH[PLCC_BOOT] -8 sectors:........ done -Erased 8 sectors -=>cp.b 100000 FFF00000 1e154 -Copy to Flash... FLASH[PLCC_BOOT]:..done -=> - - -B. FLASH RAMDISK REGION - -FLASH support is provided for an Onboard 512K RAMDISK region. - -TThe following commands will FLASH a bootrom (u-boot.bin) image -into the onboard FLASH region (AMD29LV160DB 2MB FLASH): - -tftp 100000 u-boot.bin -protect off FFF80000 FFFFFFFF -erase FFF80000 FFFFFFFF -cp.b 100000 FFF80000 \${filesize}\ - - -C. FLASH KERNEL REGION (960KB) - -FLASH support is provided for the 960KB onboard FLASH1 segment. -This allows flashing of kernel images which U-Boot can load -and run (standalone) from the onboard FLASH chip. It also assumes - -The following commands will FLASH a kernel image to 0xffe10000 - -tftp 100000 vmlinux.img -protect off FFE10000 FFEFFFFF -erase FFE10000 FFEFFFFF -cp.b 100000 FFE10000 \${filesize}\ -reset - -Here is an example: - - -=>tftp 100000 vmlinux.img -eth_halt -eth0: DC21143 Ethernet adapter(bus=0, device=13, func=0) -DEC Ethernet iobase=0x80000000 -ARP broadcast 1 -TFTP from server 209.128.93.133; our IP address is 209.128.93.138 -Filename 'vmlinux.img'. -Load address: 0x100000 -Loading: ##################################################################################################################################################### -done -Bytes transferred = 760231 (b99a7 hex) -eth_halt -=>protect off FFE10000 FFEFFFFF -Un-Protected 15 sectors -=>erase FFE10000 FFEFFFFF -Erase Flash from 0xffe10000 to 0xffefffff -Erase FLASH[F0_SA3(KERNEL)] -15 sectors:............... done -Erased 15 sectors -=>cp.b 100000 FFE10000 b99a7 -Copy to Flash... FLASH[F0_SA3(KERNEL)]:............done -=> - - -When finished, use the command: - -bootm ffe10000 - -to start the kernel. - -Finally, to make this the default boot command, use -the following commands: - -setenv bootcmd bootm ffe10000 -savenv - -to make it automatically boot the kernel from FLASH. - - -To go back to development mode (NFS boot) - -setenv bootcmd tftp 100000 vmlinux.img\;bootm -savenv - - -=>tftp 100000 vmlinux.img -eth0: DC21143 Ethernet adapter(bus=0, device=13, func=0) -DEC Ethernet iobase=0x80000000 -ARP broadcast 1 -Filename 'vmlinux.img'. -Load address: 0x100000 -Loading: #################################################################################################################################################### -done -Bytes transferred = 752717 (b7c4d hex) -eth_halt -=>protect off FFE10000 FFEFFFFF -Un-Protected 15 sectors -=>erase FFE10000 FFEFFFFF -Erase Flash from 0xffe10000 to 0xffefffff -Erase FLASH[F0_SA3(KERNEL)] -15 sectors:............... done -Erased 15 sectors -=>cp.b 100000 FFE10000 b7c4d -Copy to Flash... FLASH[F0_SA3(KERNEL)]:............done -=>bootm ffe10000 -## Booting image at ffe10000 ... - Image Name: vmlinux.bin.gz - Image Type: PowerPC Linux Kernel Image (gzip compressed) - Data Size: 752653 Bytes = 735 kB = 0 MB - Load Address: 00000000 - Entry Point: 00000000 - Verifying Checksum ... OK - Uncompressing Kernel Image ... OK -Total memory = 64MB; using 0kB for hash table (at 00000000) -Linux version 2.4.2_hhl20 (jfd@atlantis) (gcc version 2.95.2 19991024 (release)) #597 Wed Sep 5 23:23:23 PDT 2001 -cpu0: MPC8240/KAHLUA : MOUSSE Platform : 64MB RAM: MPLD Rev. 7f -Sandpoint port (C) 2000, 2001 MontaVista Software, Inc. (source@mvista.com) -IP PNP: 802.3 Ethernet Address=<0:0:10:20:30:44> -NOTICE: mounting root file system via NFS -On node 0 totalpages: 16384 -zone(0): 16384 pages. -zone(1): 0 pages. -zone(2): 0 pages. -time_init: decrementer frequency = 16.665914 MHz -time_init: MPC8240 PCI Bus frequency = 33.331828 MHz -Calibrating delay loop... 133.12 BogoMIPS -Memory: 62436k available (1336k kernel code, 500k data, 88k init, 0k highmem) -Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes) -Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes) -Page-cache hash table entries: 16384 (order: 4, 65536 bytes) -Inode-cache hash table entries: 4096 (order: 3, 32768 bytes) -POSIX conformance testing by UNIFIX -PCI: Probing PCI hardware -Linux NET4.0 for Linux 2.4 -Based upon Swansea University Computer Society NET3.039 -Initializing RT netlink socket -Starting kswapd v1.8 -pty: 256 Unix98 ptys configured -block: queued sectors max/low 41394kB/13798kB, 128 slots per queue -Uniform Multi-Platform E-IDE driver Revision: 6.31 -ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx -PDC20262: IDE controller on PCI bus 00 dev 70 -PDC20262: chipset revision 1 -PDC20262: not 100% native mode: will probe irqs later -PDC20262: ROM enabled at 0x000d0000 -PDC20262: (U)DMA Burst Bit DISABLED Primary PCI Mode Secondary PCI Mode. -PDC20262: FORCING BURST BIT 0x00 -> 0x01 ACTIVE -PDC20262: irq=3 dev->irq=3 - ide0: BM-DMA at 0xbfff00-0xbfff07, BIOS settings: hda:DMA, hdb:DMA - ide1: BM-DMA at 0xbfff08-0xbfff0f, BIOS settings: hdc:pio, hdd:pio -hda: WDC WD300AB-00BVA0, ATA DISK drive -hdc: SONY CD-RW CRX160E, ATAPI CD/DVD-ROM drive -ide0 at 0xbfff78-0xbfff7f,0xbfff76 on irq 3 -ide1 at 0xbfff68-0xbfff6f,0xbfff66 on irq 3 -hda: 58633344 sectors (30020 MB) w/2048KiB Cache, CHS=58168/16/63, UDMA(66) -hdc: ATAPI 32X CD-ROM CD-R/RW drive, 4096kB Cache -Uniform CD-ROM driver Revision: 3.12 -Partition check: - /dev/ide/host0/bus0/target0/lun0: p1 p2 -hd: unable to get major 3 for hard disk -udf: registering filesystem -loop: loaded (max 8 devices) -Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled -ttyS00 at 0xffe08080 (irq = 4) is a ST16650 -Linux Tulip driver version 0.9.13a (January 20, 2001) -eth0: Digital DS21143 Tulip rev 65 at 0xbfff80, EEPROM not present, 00:00:10:20:30:44, IRQ 1. -eth0: MII transceiver #0 config 3000 status 7829 advertising 01e1. -NET4: Linux TCP/IP 1.0 for NET4.0 -IP Protocols: ICMP, UDP, TCP -IP: routing cache hash table of 512 buckets, 4Kbytes -TCP: Hash tables configured (established 4096 bind 4096) -NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. -devfs: v0.102 (20000622) Richard Gooch (rgooch@atnf.csiro.au) -devfs: boot_options: 0x0 -VFS: Mounted root (nfs filesystem). -Mounted devfs on /dev -Freeing unused kernel memory: 88k init 4k openfirmware -eth0: Setting full-duplex based on MII#0 link partner capability of 45e1. -INIT: version 2.78 booting -INIT: Entering runlevel: 2 - - -Welcome to Linux/PPC -MPC8240/MOUSSE - - -mousse login: root -Password: -PAM_unix[13]: (login) session opened for user root by LOGIN(uid=0) -Last login: Thu Sep 6 00:16:51 2001 on console - - -Welcome to Linux/PPC -MPC8240/MOUSSE - - -mousse# |