diff options
Diffstat (limited to 'board/mbx8xx')
| -rw-r--r-- | board/mbx8xx/Makefile | 2 | ||||
| -rw-r--r-- | board/mbx8xx/pcmcia.c | 166 |
2 files changed, 167 insertions, 1 deletions
diff --git a/board/mbx8xx/Makefile b/board/mbx8xx/Makefile index 3e8376c..e4d1099 100644 --- a/board/mbx8xx/Makefile +++ b/board/mbx8xx/Makefile @@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk LIB = lib$(BOARD).a -OBJS = $(BOARD).o flash.o vpd.o +OBJS = $(BOARD).o flash.o vpd.o pcmcia.o $(LIB): .depend $(OBJS) $(AR) crv $@ $(OBJS) diff --git a/board/mbx8xx/pcmcia.c b/board/mbx8xx/pcmcia.c new file mode 100644 index 0000000..132a688 --- /dev/null +++ b/board/mbx8xx/pcmcia.c @@ -0,0 +1,166 @@ +#include <common.h> +#include <mpc8xx.h> +#include <pcmcia.h> + +#include "csr.h" + +#undef CONFIG_PCMCIA + +#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA) +#define CONFIG_PCMCIA +#endif + +#if (CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD) +#define CONFIG_PCMCIA +#endif + +#ifdef CONFIG_PCMCIA + +/* A lot of this has been taken from the RPX code in this file it works from me. + I have added the voltage selection for the MBX board. */ + +/* MBX voltage bit in control register #2 */ +#define CR2_VPP12 ((uchar)0x10) +#define CR2_VPPVDD ((uchar)0x20) +#define CR2_VDD5 ((uchar)0x40) +#define CR2_VDD3 ((uchar)0x80) + +#define PCMCIA_BOARD_MSG "MBX860" + +int pcmcia_voltage_set (int slot, int vcc, int vpp) +{ + uchar reg = 0; + + debug ("voltage_set: PCMCIA_BOARD_MSG Slot %c, Vcc=%d.%d, Vpp=%d.%d\n", + 'A' + slot, vcc / 10, vcc % 10, vpp / 10, vcc % 10); + + switch (vcc) { + case 0: + break; + case 33: + reg |= CR2_VDD3; + break; + case 50: + reg |= CR2_VDD5; + break; + default: + return 1; + } + + switch (vpp) { + case 0: + break; + case 33: + case 50: + if (vcc == vpp) { + reg |= CR2_VPPVDD; + } else { + return 1; + } + break; + case 120: + reg |= CR2_VPP12; + break; + default: + return 1; + } + + /* first, turn off all power */ + MBX_CSR2 &= ~(CR2_VDDSEL | CR2_VPPSEL); + + /* enable new powersettings */ + MBX_CSR2 |= reg; + debug ("MBX_CSR2 read = 0x%02x\n", MBX_CSR2); + + return (0); +} + +int pcmcia_hardware_enable (int slot) +{ + volatile immap_t *immap; + volatile cpm8xx_t *cp; + volatile pcmconf8xx_t *pcmp; + volatile sysconf8xx_t *sysp; + uint reg, mask; + + debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", + 'A' + slot); + + udelay (10000); + + immap = (immap_t *) CFG_IMMR; + sysp = (sysconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_siu_conf)); + pcmp = (pcmconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_pcmcia)); + cp = (cpm8xx_t *) (&(((immap_t *) CFG_IMMR)->im_cpm)); + + /* clear interrupt state, and disable interrupts */ + pcmp->pcmc_pscr = PCMCIA_MASK (_slot_); + pcmp->pcmc_per &= ~PCMCIA_MASK (_slot_); + + /* + * Disable interrupts, DMA, and PCMCIA buffers + * (isolate the interface) and assert RESET signal + */ + debug ("Disable PCMCIA buffers and assert RESET\n"); + reg = 0; + reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */ + reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */ + PCMCIA_PGCRX (_slot_) = reg; + udelay (500); + + /* remove all power */ + pcmcia_voltage_set (slot, 0, 0); + /* + * Make sure there is a card in the slot, then configure the interface. + */ + udelay(10000); + debug ("[%d] %s: PIPR(%p)=0x%x\n", + __LINE__,__FUNCTION__, + &(pcmp->pcmc_pipr),pcmp->pcmc_pipr); +#ifndef CONFIG_HMI10 + if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) { +#else + if (pcmp->pcmc_pipr & (0x10000000 >> (slot << 4))) { +#endif /* CONFIG_HMI10 */ + printf (" No Card found\n"); + return (1); + } + + /* + * Power On. + */ + mask = PCMCIA_VS1 (_slot_) | PCMCIA_VS2 (_slot_); + reg = pcmp->pcmc_pipr; + debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n", reg, + (reg & PCMCIA_VS1 (slot)) ? "n" : "ff", + (reg & PCMCIA_VS2 (slot)) ? "n" : "ff"); + + if ((reg & mask) == mask) { + pcmcia_voltage_set (_slot_, 50, 0); + printf (" 5.0V card found: "); + } else { + pcmcia_voltage_set (_slot_, 33, 0); + printf (" 3.3V card found: "); + } + + debug ("Enable PCMCIA buffers and stop RESET\n"); + reg = PCMCIA_PGCRX (_slot_); + reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */ + reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */ + PCMCIA_PGCRX (_slot_) = reg; + + udelay (250000); /* some cards need >150 ms to come up :-( */ + + debug ("# hardware_enable done\n"); + + return (0); + } + +#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA) +int pcmcia_hardware_disable (int slot) +{ + return 0; /* No hardware to disable */ +} +#endif /* CFG_CMD_PCMCIA */ + +#endif /* CONFIG_PCMCIA */ |