diff options
Diffstat (limited to 'board/korat')
| -rw-r--r-- | board/korat/korat.c | 117 |
1 files changed, 9 insertions, 108 deletions
diff --git a/board/korat/korat.c b/board/korat/korat.c index 7cb9ee1..199c1ff 100644 --- a/board/korat/korat.c +++ b/board/korat/korat.c @@ -1,5 +1,5 @@ /* - * (C) Copyright 2007 + * (C) Copyright 2007-2008 * Larry Johnson, lrj@acm.org * * (C) Copyright 2006 @@ -26,6 +26,7 @@ */ #include <common.h> +#include <asm/gpio.h> #include <asm/processor.h> #include <asm-ppc/io.h> #include <i2c.h> @@ -40,7 +41,6 @@ ulong flash_get_size(ulong base, int banknum); int board_early_init_f(void) { u32 sdr0_pfc1, sdr0_pfc2; - u32 gpio0_ir; u32 reg; int eth; @@ -48,102 +48,6 @@ int board_early_init_f(void) mtdcr(ebccfgd, 0xb8400000); /*-------------------------------------------------------------------- - * Setup the GPIO pins - * - * Korat GPIO usage: - * - * Init. - * Pin Source I/O value Function - * ------ ------ --- ----- --------------------------------- - * GPIO00 Alt1 I/O x PerAddr07 - * GPIO01 Alt1 I/O x PerAddr06 - * GPIO02 Alt1 I/O x PerAddr05 - * GPIO03 GPIO x x GPIO03 to expansion bus connector - * GPIO04 GPIO x x GPIO04 to expansion bus connector - * GPIO05 GPIO x x GPIO05 to expansion bus connector - * GPIO06 Alt1 O x PerCS1 (2nd NOR flash) - * GPIO07 Alt1 O x PerCS2 (CPLD) - * GPIO08 Alt1 O x PerCS3 to expansion bus connector - * GPIO09 Alt1 O x PerCS4 to expansion bus connector - * GPIO10 Alt1 O x PerCS5 to expansion bus connector - * GPIO11 Alt1 I x PerErr - * GPIO12 GPIO O 0 ATMega !Reset - * GPIO13 GPIO O 1 SPI Atmega !SS - * GPIO14 GPIO O 1 Write protect EEPROM #1 (0xA8) - * GPIO15 GPIO O 0 CPU Run LED !On - * GPIO16 Alt1 O x GMC1TxD0 - * GPIO17 Alt1 O x GMC1TxD1 - * GPIO18 Alt1 O x GMC1TxD2 - * GPIO19 Alt1 O x GMC1TxD3 - * GPIO20 Alt1 O x RejectPkt0 - * GPIO21 Alt1 O x RejectPkt1 - * GPIO22 GPIO I x PGOOD_DDR - * GPIO23 Alt1 O x SCPD0 - * GPIO24 Alt1 O x GMC0TxD2 - * GPIO25 Alt1 O x GMC0TxD3 - * GPIO26 GPIO? I/O x IIC0SDA (selected in SDR0_PFC4) - * GPIO27 GPIO O 0 PHY #0 1000BASE-X - * GPIO28 GPIO O 0 PHY #1 1000BASE-X - * GPIO29 GPIO I x Test jumper !Present - * GPIO30 GPIO I x SFP module #0 !Present - * GPIO31 GPIO I x SFP module #1 !Present - * - * GPIO32 GPIO O 1 SFP module #0 Tx !Enable - * GPIO33 GPIO O 1 SFP module #1 Tx !Enable - * GPIO34 Alt2 I x !UART1_CTS - * GPIO35 Alt2 O x !UART1_RTS - * GPIO36 Alt1 I x !UART0_CTS - * GPIO37 Alt1 O x !UART0_RTS - * GPIO38 Alt2 O x UART1_Tx - * GPIO39 Alt2 I x UART1_Rx - * GPIO40 Alt1 I x IRQ0 (Ethernet 0) - * GPIO41 Alt1 I x IRQ1 (Ethernet 1) - * GPIO42 Alt1 I x IRQ2 (PCI interrupt) - * GPIO43 Alt1 I x IRQ3 (System Alert from CPLD) - * GPIO44 xxxx x x (grounded through pulldown) - * GPIO45 GPIO O 0 PHY #0 Enable - * GPIO46 GPIO O 0 PHY #1 Enable - * GPIO47 GPIO I x Reset switch !Pressed - * GPIO48 GPIO I x Shutdown switch !Pressed - * GPIO49 xxxx x x (reserved for trace port) - * . . . . . - * . . . . . - * . . . . . - * GPIO63 xxxx x x (reserved for trace port) - *-------------------------------------------------------------------*/ - - out_be32((u32 *) GPIO0_OR, 0x00060000); - out_be32((u32 *) GPIO1_OR, 0xC0000000); - - out_be32((u32 *) GPIO0_OSRL, 0x54055400); - out_be32((u32 *) GPIO0_OSRH, 0x55015000); - out_be32((u32 *) GPIO1_OSRL, 0x02180000); - out_be32((u32 *) GPIO1_OSRH, 0x00000000); - - out_be32((u32 *) GPIO0_TSRL, 0x54055500); - out_be32((u32 *) GPIO0_TSRH, 0x00015000); - out_be32((u32 *) GPIO1_TSRL, 0x00000000); - out_be32((u32 *) GPIO1_TSRH, 0x00000000); - - out_be32((u32 *) GPIO0_TCR, 0x000FF0D8); - out_be32((u32 *) GPIO1_TCR, 0xD6060000); - - out_be32((u32 *) GPIO0_ISR1L, 0x54000100); - out_be32((u32 *) GPIO0_ISR1H, 0x00500000); - out_be32((u32 *) GPIO1_ISR1L, 0x00405500); - out_be32((u32 *) GPIO1_ISR1H, 0x00000000); - - out_be32((u32 *) GPIO0_ISR2L, 0x00000000); - out_be32((u32 *) GPIO0_ISR2H, 0x00000000); - out_be32((u32 *) GPIO1_ISR2L, 0x04010000); - out_be32((u32 *) GPIO1_ISR2H, 0x00000000); - - out_be32((u32 *) GPIO0_ISR3L, 0x00000000); - out_be32((u32 *) GPIO0_ISR3H, 0x00000000); - out_be32((u32 *) GPIO1_ISR3L, 0x00000000); - out_be32((u32 *) GPIO1_ISR3H, 0x00000000); - - /*-------------------------------------------------------------------- * Setup the interrupt controller polarities, triggers, etc. *-------------------------------------------------------------------*/ mtdcr(uic0sr, 0xffffffff); /* clear all */ @@ -176,9 +80,8 @@ int board_early_init_f(void) /* Configure the two Ethernet PHYs. For each PHY, configure for fiber * if the SFP module is present, and for copper if it is not present. */ - gpio0_ir = in_be32((u32 *) GPIO0_IR); for (eth = 0; eth < 2; ++eth) { - if (gpio0_ir & (0x00000001 << (1 - eth))) { + if (gpio_read_in_bit(CFG_GPIO_SFP0_PRESENT_ + eth)) { /* SFP module not present: configure PHY for copper. */ /* Set PHY to autonegotate 10 MB, 100MB, or 1 GB */ out_8((u8 *) CFG_CPLD_BASE + 0x06, @@ -187,14 +90,13 @@ int board_early_init_f(void) } else { /* SFP module present: configure PHY for fiber and enable output */ - out_be32((u32 *) GPIO0_OR, in_be32((u32 *) GPIO0_OR) | - (0x00000001 << (4 - eth))); - out_be32((u32 *) GPIO1_OR, in_be32((u32 *) GPIO1_OR) & - ~(0x00000001 << (31 - eth))); + gpio_write_bit(CFG_GPIO_PHY0_FIBER_SEL + eth, 1); + gpio_write_bit(CFG_GPIO_SFP0_TX_EN_ + eth, 0); } } /* enable Ethernet: set GPIO45 and GPIO46 to 1 */ - out_be32((u32 *) GPIO1_OR, in_be32((u32 *) GPIO1_OR) | 0x00060000); + gpio_write_bit(CFG_GPIO_PHY0_EN, 1); + gpio_write_bit(CFG_GPIO_PHY1_EN, 1); /* select Ethernet pins */ mfsdr(SDR0_PFC1, sdr0_pfc1); @@ -525,20 +427,19 @@ int checkboard(void) { char const *const s = getenv("serial#"); u8 const rev = in_8((u8 *) CFG_CPLD_BASE + 0); - u32 const gpio0_or = in_be32((u32 *) GPIO0_OR); printf("Board: Korat, Rev. %X", rev); if (s != NULL) printf(", serial# %s", s); printf(", Ethernet PHY 0: "); - if (gpio0_or & 0x00000010) + if (gpio_read_out_bit(CFG_GPIO_PHY0_FIBER_SEL)) printf("fiber"); else printf("copper"); printf(", PHY 1: "); - if (gpio0_or & 0x00000008) + if (gpio_read_out_bit(CFG_GPIO_PHY1_FIBER_SEL)) printf("fiber"); else printf("copper"); |