diff options
Diffstat (limited to 'board/gdsys/gdppc440etx/gdppc440etx.c')
-rw-r--r-- | board/gdsys/gdppc440etx/gdppc440etx.c | 323 |
1 files changed, 323 insertions, 0 deletions
diff --git a/board/gdsys/gdppc440etx/gdppc440etx.c b/board/gdsys/gdppc440etx/gdppc440etx.c new file mode 100644 index 0000000..a661057 --- /dev/null +++ b/board/gdsys/gdppc440etx/gdppc440etx.c @@ -0,0 +1,323 @@ +/* + * (C) Copyright 2008 + * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de + * + * Based on board/amcc/yosemite/yosemite.c + * (C) Copyright 2006-2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <ppc4xx.h> +#include <asm/processor.h> +#include <asm/io.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* info for FLASH chips */ +extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; + +int board_early_init_f(void) +{ + register uint reg; + + /* + * Setup the external bus controller/chip selects + */ + mfebc(xbcfg, reg); + mtebc(xbcfg, reg | 0x04000000); /* Set ATC */ + + /* + * Setup the GPIO pins + */ + + /* setup Address lines for flash size 64Meg. */ + out32(GPIO0_OSRL, in32(GPIO0_OSRL) | 0x54000000); + out32(GPIO0_TSRL, in32(GPIO0_TSRL) | 0x54000000); + out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) | 0x54000000); + + /* setup emac */ + out32(GPIO0_TCR, in32(GPIO0_TCR) | 0xC080); + out32(GPIO0_TSRL, in32(GPIO0_TSRL) | 0x40); + out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) | 0x55); + out32(GPIO0_OSRH, in32(GPIO0_OSRH) | 0x50004000); + out32(GPIO0_ISR1H, in32(GPIO0_ISR1H) | 0x00440000); + + /* UART0 and UART1*/ + out32(GPIO1_TCR, in32(GPIO1_TCR) | 0x16000000); + out32(GPIO1_OSRL, in32(GPIO1_OSRL) | 0x02180000); + out32(GPIO1_ISR1L, in32(GPIO1_ISR1L) | 0x00400000); + out32(GPIO1_ISR2L, in32(GPIO1_ISR2L) | 0x04010000); + + /* disable boot-eeprom WP */ + out32(GPIO0_OSRL, in32(GPIO0_OSRL) & ~0x00C00000); + out32(GPIO0_TSRL, in32(GPIO0_TSRL) & ~0x00C00000); + out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) & ~0x00C00000); + out32(GPIO0_TCR, in32(GPIO0_TCR) | 0x08000000); + out32(GPIO0_OR, in32(GPIO0_OR) & ~0x08000000); + + /* external interrupts IRQ0...3 */ + out32(GPIO1_TCR, in32(GPIO1_TCR) & ~0x00f00000); + out32(GPIO1_TSRL, in32(GPIO1_TSRL) & ~0x00005500); + out32(GPIO1_ISR1L, in32(GPIO1_ISR1L) | 0x00005500); + + + /* + * Setup the interrupt controller polarities, triggers, etc. + */ + mtdcr(uic0sr, 0xffffffff); /* clear all */ + mtdcr(uic0er, 0x00000000); /* disable all */ + mtdcr(uic0cr, 0x00000009); /* ATI & UIC1 crit are critical */ + mtdcr(uic0pr, 0xfffffe13); /* per ref-board manual */ + mtdcr(uic0tr, 0x01c00008); /* per ref-board manual */ + mtdcr(uic0vr, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr(uic0sr, 0xffffffff); /* clear all */ + + mtdcr(uic1sr, 0xffffffff); /* clear all */ + mtdcr(uic1er, 0x00000000); /* disable all */ + mtdcr(uic1cr, 0x00000000); /* all non-critical */ + mtdcr(uic1pr, 0xffffe0ff); /* per ref-board manual */ + mtdcr(uic1tr, 0x00ffc000); /* per ref-board manual */ + mtdcr(uic1vr, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr(uic1sr, 0xffffffff); /* clear all */ + + /* + * Setup other serial configuration + */ + mfsdr(sdr_pci0, reg); + mtsdr(sdr_pci0, 0x80000000 | reg); /* PCI arbiter enabled */ + mtsdr(sdr_pfc0, 0x00003e00); /* Pin function */ + mtsdr(sdr_pfc1, 0x00048000); /* Pin function: UART0 has 4 pins */ + + return 0; +} + +int misc_init_r(void) +{ + uint pbcr; + int size_val; + uint sz; + + /* Re-do sizing to get full correct info */ + mfebc(pb0cr, pbcr); + + if (gd->bd->bi_flashsize > 0x08000000) + panic("Max. flash banksize is 128 MB!\n"); + + for (sz = gd->bd->bi_flashsize, size_val = 7; + ((sz & 0x08000000) == 0) && (size_val > 0); --size_val) + sz <<= 1; + + pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17); + mtebc(pb0cr, pbcr); + + /* adjust flash start and offset */ + gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize; + gd->bd->bi_flashoffset = 0; + + /* Monitor protection ON by default */ + (void)flash_protect(FLAG_PROTECT_SET, + -CONFIG_SYS_MONITOR_LEN, + 0xffffffff, + &flash_info[0]); + + return 0; +} + +int checkboard(void) +{ + char *s = getenv("serial#"); + + printf("Board: GDPPC440ETX - G&D PPC440EP/GR ETX-module"); + + if (s != NULL) { + puts(", serial# "); + puts(s); + } + putc('\n'); + + return 0; +} + +/* + * pci_pre_init + * + * This routine is called just prior to registering the hose and gives + * the board the opportunity to check things. Returning a value of zero + * indicates that things are bad & PCI initialization should be aborted. + * + * Different boards may wish to customize the pci controller structure + * (add regions, override default access routines, etc) or perform + * certain pre-initialization actions. + * + */ +#if defined(CONFIG_PCI) +int pci_pre_init(struct pci_controller *hose) +{ + unsigned long addr; + + /* + * Set priority for all PLB3 devices to 0. + * Set PLB3 arbiter to fair mode. + */ + mfsdr(sdr_amp1, addr); + mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00); + addr = mfdcr(plb3_acr); + mtdcr(plb3_acr, addr | 0x80000000); + + /* + * Set priority for all PLB4 devices to 0. + */ + mfsdr(sdr_amp0, addr); + mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00); + addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */ + mtdcr(plb4_acr, addr); + + /* + * Set Nebula PLB4 arbiter to fair mode. + */ + /* Segment0 */ + addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair; + addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled; + addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep; + addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep; + mtdcr(plb0_acr, addr); + + /* Segment1 */ + addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair; + addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled; + addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep; + addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep; + mtdcr(plb1_acr, addr); + + /* enable 66 MHz ext. Clock */ + out32(GPIO1_TCR, in32(GPIO1_TCR) | 0x00008000); + out32(GPIO1_OR, in32(GPIO1_OR) | 0x00008000); + + return 1; +} +#endif /* defined(CONFIG_PCI) */ + +/* + * pci_target_init + * + * The bootstrap configuration provides default settings for the pci + * inbound map (PIM). But the bootstrap config choices are limited and + * may not be sufficient for a given board. + * + */ +#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) +void pci_target_init(struct pci_controller *hose) +{ + /* + * Set up Direct MMIO registers + */ + + /* + * PowerPC440 EP PCI Master configuration. + * Map one 1Gig range of PLB/processor addresses to PCI memory space. + * PLB address 0xA0000000-0xDFFFFFFF + * ==> PCI address 0xA0000000-0xDFFFFFFF + * Use byte reversed out routines to handle endianess. + * Make this region non-prefetchable. + */ + out32r(PCIX0_PMM0MA, 0x00000000); /* disabled b4 setting */ + out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); + out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); + out32r(PCIX0_PMM0PCIHA, 0x00000000); + out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M, no prefetch, enable region */ + + out32r(PCIX0_PMM1MA, 0x00000000); /* disabled b4 setting */ + out32r(PCIX0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); + out32r(PCIX0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); + out32r(PCIX0_PMM1PCIHA, 0x00000000); + out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M, no prefetch, enable region */ + + out32r(PCIX0_PTM1MS, 0x00000001); + out32r(PCIX0_PTM1LA, 0); + out32r(PCIX0_PTM2MS, 0); + out32r(PCIX0_PTM2LA, 0); + + /* + * Set up Configuration registers + */ + + /* Program the board's subsystem id/vendor id */ + pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID, + CONFIG_SYS_PCI_SUBSYS_VENDORID); + pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID); + + /* Configure command register as bus master */ + pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER); + + /* 240nS PCI clock */ + pci_write_config_word(0, PCI_LATENCY_TIMER, 1); + + /* No error reporting */ + pci_write_config_word(0, PCI_ERREN, 0); + + pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101); + +} +#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */ + +/* + * pci_master_init + * + */ +#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) +void pci_master_init(struct pci_controller *hose) +{ + unsigned short temp_short; + + /* + * Write the PowerPC440 EP PCI Configuration regs. + * Enable PowerPC440 EP to be a master on the PCI bus (PMM). + * Enable PowerPC440 EP to act as a PCI memory target (PTM). + */ + pci_read_config_word(0, PCI_COMMAND, &temp_short); + pci_write_config_word(0, PCI_COMMAND, + temp_short | PCI_COMMAND_MASTER | + PCI_COMMAND_MEMORY); +} +#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */ + +/* + * is_pci_host + * + * This routine is called to determine if a pci scan should be + * performed. With various hardware environments (especially cPCI and + * PPMC) it's insufficient to depend on the state of the arbiter enable + * bit in the strap register, or generic host/adapter assumptions. + * + * Rather than hard-code a bad assumption in the general 440 code, the + * 440 pci code requires the board to decide at runtime. + * + * Return 0 for adapter mode, non-zero for host (monarch) mode. + * + * + */ +#if defined(CONFIG_PCI) +int is_pci_host(struct pci_controller *hose) +{ + return 1; +} +#endif /* defined(CONFIG_PCI) */ |