diff options
Diffstat (limited to 'board/freescale')
94 files changed, 4530 insertions, 174 deletions
diff --git a/board/freescale/b4860qds/b4860qds.c b/board/freescale/b4860qds/b4860qds.c index 34d66d5..6a8fca6 100644 --- a/board/freescale/b4860qds/b4860qds.c +++ b/board/freescale/b4860qds/b4860qds.c @@ -19,6 +19,7 @@ #include <asm/fsl_portals.h> #include <asm/fsl_liodn.h> #include <fm_eth.h> +#include <hwconfig.h> #include "../common/qixis.h" #include "../common/vsc3316_3308.h" @@ -333,6 +334,8 @@ int configure_vsc3316_3308(void) unsigned int num_vsc16_con, num_vsc08_con; u32 serdes1_prtcl, serdes2_prtcl; int ret; + char buffer[HWCONFIG_BUFFER_SIZE]; + char *buf = NULL; serdes1_prtcl = in_be32(&gur->rcwsr[4]) & FSL_CORENET2_RCWSR4_SRDS1_PRTCL; @@ -385,15 +388,18 @@ int configure_vsc3316_3308(void) } break; + case 0x01: case 0x02: case 0x04: case 0x05: case 0x06: + case 0x07: case 0x08: case 0x09: case 0x0A: case 0x0B: case 0x0C: + case 0x2F: case 0x30: case 0x32: case 0x33: @@ -487,6 +493,9 @@ int configure_vsc3316_3308(void) return -1; } + num_vsc08_con = NUM_CON_VSC3308; + /* Configure VSC3308 crossbar switch */ + ret = select_i2c_ch_pca(I2C_CH_VSC3308); switch (serdes2_prtcl) { #ifdef CONFIG_PPC_B4420 case 0x9d: @@ -494,14 +503,11 @@ int configure_vsc3316_3308(void) case 0x9E: case 0x9A: case 0x98: - case 0xb2: + case 0x48: case 0x49: case 0x4E: - case 0x8D: + case 0x79: case 0x7A: - num_vsc08_con = NUM_CON_VSC3308; - /* Configure VSC3308 crossbar switch */ - ret = select_i2c_ch_pca(I2C_CH_VSC3308); if (!ret) { ret = vsc3308_config(VSC3308_TX_ADDRESS, vsc08_tx_amc, num_vsc08_con); @@ -515,6 +521,71 @@ int configure_vsc3316_3308(void) return ret; } break; + case 0x80: + case 0x81: + case 0x82: + case 0x83: + case 0x84: + case 0x85: + case 0x86: + case 0x87: + case 0x88: + case 0x89: + case 0x8a: + case 0x8b: + case 0x8c: + case 0x8d: + case 0x8e: + case 0xb1: + case 0xb2: + if (!ret) { + /* + * Extract hwconfig from environment since environment + * is not setup properly yet + */ + getenv_f("hwconfig", buffer, sizeof(buffer)); + buf = buffer; + + if (hwconfig_subarg_cmp_f("fsl_b4860_serdes2", + "sfp_amc", "sfp", buf)) { +#ifdef CONFIG_SYS_FSL_B4860QDS_XFI_ERR + /* change default VSC3308 for XFI erratum */ + ret = vsc3308_config_adjust(VSC3308_TX_ADDRESS, + vsc08_tx_sfp, num_vsc08_con); + if (ret) + return ret; + + ret = vsc3308_config_adjust(VSC3308_RX_ADDRESS, + vsc08_rx_sfp, num_vsc08_con); + if (ret) + return ret; +#else + ret = vsc3308_config(VSC3308_TX_ADDRESS, + vsc08_tx_sfp, num_vsc08_con); + if (ret) + return ret; + + ret = vsc3308_config(VSC3308_RX_ADDRESS, + vsc08_rx_sfp, num_vsc08_con); + if (ret) + return ret; +#endif + } else { + ret = vsc3308_config(VSC3308_TX_ADDRESS, + vsc08_tx_amc, num_vsc08_con); + if (ret) + return ret; + + ret = vsc3308_config(VSC3308_RX_ADDRESS, + vsc08_rx_amc, num_vsc08_con); + if (ret) + return ret; + } + + } else { + return ret; + } + break; default: printf("WARNING:VSC crossbars programming not supported for: %x" " SerDes2 Protocol.\n", serdes2_prtcl); @@ -730,19 +801,23 @@ int config_serdes1_refclks(void) * to 122.88MHz */ switch (serdes1_prtcl) { + case 0x29: case 0x2A: case 0x2C: case 0x2D: case 0x2E: + case 0x01: case 0x02: case 0x04: case 0x05: case 0x06: + case 0x07: case 0x08: case 0x09: case 0x0A: case 0x0B: case 0x0C: + case 0x2F: case 0x30: case 0x32: case 0x33: @@ -860,6 +935,8 @@ int config_serdes2_refclks(void) #endif case 0x9E: case 0x9A: + /* fallthrough */ + case 0xb1: case 0xb2: debug("Configuring IDT for PCIe SATA for srds_prctl:%x\n", serdes2_prtcl); @@ -915,6 +992,14 @@ int board_early_init_r(void) const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; int flash_esel = find_tlb_idx((void *)flashbase, 1); int ret; + u32 svr = SVR_SOC_VER(get_svr()); + + /* Create law for MAPLE only for personalities having MAPLE */ + if ((svr == SVR_B4860) || (svr == SVR_B4440) || + (svr == SVR_B4420) || (svr == SVR_B4220)) { + set_next_law(CONFIG_SYS_MAPLE_MEM_PHYS, LAW_SIZE_16M, + LAW_TRGT_IF_MAPLE); + } /* * Remap Boot flash + PROMJET region to caching-inhibited @@ -1110,7 +1195,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -1136,6 +1221,8 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_fman_ethernet(blob); fdt_fixup_board_enet(blob); #endif + + return 0; } /* diff --git a/board/freescale/b4860qds/eth_b4860qds.c b/board/freescale/b4860qds/eth_b4860qds.c index 12df9a8..501d4b3 100644 --- a/board/freescale/b4860qds/eth_b4860qds.c +++ b/board/freescale/b4860qds/eth_b4860qds.c @@ -112,7 +112,10 @@ static void initialize_lane_to_slot(void) * Lanes: A,B,C,D: PCI * Lanes: E,F,G,H: XAUI2 */ + case 0xb1: case 0xb2: + case 0x8c: + case 0x8d: /* * Configuration: * SERDES: 2 @@ -195,34 +198,34 @@ int board_eth_init(bd_t *bis) * all SGMII. RGMII is not supported on this board. Setting SGMII 5 and * 6 to on board SGMII phys */ - fm_info_set_phy_address(FM1_DTSEC5, CONFIG_SYS_FM1_DTSEC5_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC6, CONFIG_SYS_FM1_DTSEC6_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC5, CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR); + fm_info_set_phy_address(FM1_DTSEC6, CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR); switch (serdes1_prtcl) { case 0x29: case 0x2a: /* Serdes 1: A-B SGMII, Configuring DTSEC 5 and 6 */ - debug("Setting phy addresses for FM1_DTSEC5: %x and" - "FM1_DTSEC6: %x\n", CONFIG_SYS_FM1_DTSEC5_PHY_ADDR, - CONFIG_SYS_FM1_DTSEC6_PHY_ADDR); + debug("Set phy addresses for FM1_DTSEC5:%x, FM1_DTSEC6:%x\n", + CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR, + CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR); fm_info_set_phy_address(FM1_DTSEC5, - CONFIG_SYS_FM1_DTSEC5_PHY_ADDR); + CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR); fm_info_set_phy_address(FM1_DTSEC6, - CONFIG_SYS_FM1_DTSEC6_PHY_ADDR); + CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR); break; #ifdef CONFIG_PPC_B4420 case 0x17: case 0x18: /* Serdes 1: A-D SGMII, Configuring on board dual SGMII Phy */ - debug("Setting phy addresses for FM1_DTSEC3: %x and" - "FM1_DTSEC4: %x\n", CONFIG_SYS_FM1_DTSEC5_PHY_ADDR, - CONFIG_SYS_FM1_DTSEC6_PHY_ADDR); + debug("Set phy addresses for FM1_DTSEC3:%x, FM1_DTSEC4:%x\n", + CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR, + CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR); /* Fixing Serdes clock by programming FPGA register */ QIXIS_WRITE(brdcfg[4], QIXIS_SRDS1CLK_125); fm_info_set_phy_address(FM1_DTSEC3, - CONFIG_SYS_FM1_DTSEC5_PHY_ADDR); + CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR); fm_info_set_phy_address(FM1_DTSEC4, - CONFIG_SYS_FM1_DTSEC6_PHY_ADDR); + CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR); break; #endif default: @@ -233,8 +236,8 @@ int board_eth_init(bd_t *bis) switch (serdes2_prtcl) { case 0x17: case 0x18: - debug("Setting phy addresses on SGMII Riser card for" - "FM1_DTSEC ports: \n"); + debug("Set phy address on SGMII Riser for FM1_DTSEC1:%x\n", + CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR); fm_info_set_phy_address(FM1_DTSEC1, CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR); fm_info_set_phy_address(FM1_DTSEC2, @@ -246,8 +249,8 @@ int board_eth_init(bd_t *bis) break; case 0x48: case 0x49: - debug("Setting phy addresses on SGMII Riser card for" - "FM1_DTSEC ports: \n"); + debug("Set phy address on SGMII Riser for FM1_DTSEC1:%x\n", + CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR); fm_info_set_phy_address(FM1_DTSEC1, CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR); fm_info_set_phy_address(FM1_DTSEC2, @@ -255,29 +258,37 @@ int board_eth_init(bd_t *bis) fm_info_set_phy_address(FM1_DTSEC3, CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR); break; - case 0x8d: + case 0xb1: case 0xb2: - debug("Setting phy addresses on SGMII Riser card for" - "FM1_DTSEC ports: \n"); + case 0x8c: + case 0x8d: + debug("Set phy addresses on SGMII Riser for FM1_DTSEC1:%x\n", + CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR); fm_info_set_phy_address(FM1_DTSEC3, CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR); fm_info_set_phy_address(FM1_DTSEC4, CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR); + /* + * XFI does not need a PHY to work, but to make U-boot + * happy, assign a fake PHY address for a XFI port. + */ + fm_info_set_phy_address(FM1_10GEC1, 0); + fm_info_set_phy_address(FM1_10GEC2, 1); break; case 0x98: /* XAUI in Slot1 and Slot2 */ - debug("Setting phy addresses on B4860 QDS AMC2PEX-2S for FM1_10GEC1: %x\n", + debug("Set phy address of AMC2PEX-2S for FM1_10GEC1:%x\n", CONFIG_SYS_FM1_10GEC1_PHY_ADDR); fm_info_set_phy_address(FM1_10GEC1, CONFIG_SYS_FM1_10GEC1_PHY_ADDR); - debug("Setting phy addresses on B4860 QDS AMC2PEX-2S for FM1_10GEC2: %x\n", + debug("Set phy address of AMC2PEX-2S for FM1_10GEC2:%x\n", CONFIG_SYS_FM1_10GEC2_PHY_ADDR); fm_info_set_phy_address(FM1_10GEC2, CONFIG_SYS_FM1_10GEC2_PHY_ADDR); break; case 0x9E: /* XAUI in Slot2 */ - debug("Setting phy addresses on B4860 QDS AMC2PEX-2S for FM1_10GEC2: %x\n", + debug("Sett phy address of AMC2PEX-2S for FM1_10GEC2:%x\n", CONFIG_SYS_FM1_10GEC2_PHY_ADDR); fm_info_set_phy_address(FM1_10GEC2, CONFIG_SYS_FM1_10GEC2_PHY_ADDR); @@ -329,17 +340,20 @@ int board_eth_init(bd_t *bis) switch (fm_info_get_enet_if(i)) { case PHY_INTERFACE_MODE_XGMII: fm_info_set_mdio(i, - miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME)); + miiphy_get_dev_by_name + (DEFAULT_FM_TGEC_MDIO_NAME)); + break; + case PHY_INTERFACE_MODE_NONE: + fm_info_set_phy_address(i, 0); break; default: - printf("Fman1: 10GSEC%u set to unknown interface %i\n", + printf("Fman1: TGEC%u set to unknown interface %i\n", idx + 1, fm_info_get_enet_if(i)); fm_info_set_phy_address(i, 0); break; } } - cpu_eth_init(bis); #endif @@ -351,21 +365,82 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, { int phy; char alias[32]; + struct fixed_link f_link; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 prtcl2 = in_be32(&gur->rcwsr[4]) & FSL_CORENET2_RCWSR4_SRDS2_PRTCL; + + prtcl2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT; if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) { phy = fm_info_get_phy_address(port); sprintf(alias, "phy_sgmii_%x", phy); fdt_set_phy_handle(fdt, compat, addr, alias); + fdt_status_okay_by_alias(fdt, alias); + } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII) { + /* check if it's XFI interface for 10g */ + switch (prtcl2) { + case 0x80: + case 0x81: + case 0x82: + case 0x83: + case 0x84: + case 0x85: + case 0x86: + case 0x87: + case 0x88: + case 0x89: + case 0x8a: + case 0x8b: + case 0x8c: + case 0x8d: + case 0x8e: + case 0xb1: + case 0xb2: + f_link.phy_id = port; + f_link.duplex = 1; + f_link.link_speed = 10000; + f_link.pause = 0; + f_link.asym_pause = 0; + + fdt_delprop(fdt, offset, "phy-handle"); + fdt_setprop(fdt, offset, "fixed-link", &f_link, + sizeof(f_link)); + break; + case 0x98: /* XAUI interface */ + sprintf(alias, "phy_xaui_slot1"); + fdt_status_okay_by_alias(fdt, alias); + + sprintf(alias, "phy_xaui_slot2"); + fdt_status_okay_by_alias(fdt, alias); + break; + case 0x9e: /* XAUI interface */ + case 0x9a: + case 0x93: + case 0x91: + sprintf(alias, "phy_xaui_slot1"); + fdt_status_okay_by_alias(fdt, alias); + break; + case 0x97: /* XAUI interface */ + case 0xc3: + sprintf(alias, "phy_xaui_slot2"); + fdt_status_okay_by_alias(fdt, alias); + break; + default: + break; + } } } +/* + * Set status to disabled for unused ethernet node + */ void fdt_fixup_board_enet(void *fdt) { int i; char alias[32]; - for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { + for (i = FM1_DTSEC1; i <= FM1_10GEC2; i++) { switch (fm_info_get_enet_if(i)) { case PHY_INTERFACE_MODE_NONE: sprintf(alias, "ethernet%u", i); diff --git a/board/freescale/b4860qds/law.c b/board/freescale/b4860qds/law.c index 5b327cc..047c3cb 100644 --- a/board/freescale/b4860qds/law.c +++ b/board/freescale/b4860qds/law.c @@ -17,9 +17,6 @@ struct law_entry law_table[] = { SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN), #endif SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC), -#ifdef CONFIG_SYS_MAPLE_MEM_PHYS - SET_LAW(CONFIG_SYS_MAPLE_MEM_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_MAPLE), -#endif #ifdef CONFIG_SYS_DCSRBAR_PHYS /* Limit DCSR to 32M to access NPC Trace Buffer */ SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR), diff --git a/board/freescale/bsc9131rdb/bsc9131rdb.c b/board/freescale/bsc9131rdb/bsc9131rdb.c index 9146f49..75e1142 100644 --- a/board/freescale/bsc9131rdb/bsc9131rdb.c +++ b/board/freescale/bsc9131rdb/bsc9131rdb.c @@ -58,7 +58,7 @@ struct node_info nodes[] = { { "fsl,ifc-nand", MTD_DEV_TYPE_NAND, }, }; #endif -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -74,5 +74,7 @@ void ft_board_setup(void *blob, bd_t *bd) #endif fdt_fixup_dr_usb(blob, bd); + + return 0; } #endif diff --git a/board/freescale/bsc9132qds/bsc9132qds.c b/board/freescale/bsc9132qds/bsc9132qds.c index c88838b..36a68db 100644 --- a/board/freescale/bsc9132qds/bsc9132qds.c +++ b/board/freescale/bsc9132qds/bsc9132qds.c @@ -363,7 +363,7 @@ struct node_info nodes[] = { { "fsl,ifc-nand", MTD_DEV_TYPE_NAND, }, }; #endif -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -423,5 +423,7 @@ void ft_board_setup(void *blob, bd_t *bd) printf("\nRemove sim from hwconfig and reset\n"); } } + + return 0; } #endif diff --git a/board/freescale/c29xpcie/c29xpcie.c b/board/freescale/c29xpcie/c29xpcie.c index 534c6d1..d7577096 100644 --- a/board/freescale/c29xpcie/c29xpcie.c +++ b/board/freescale/c29xpcie/c29xpcie.c @@ -128,7 +128,7 @@ void fdt_del_sec(void *blob, int offset) } } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -150,5 +150,7 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_del_sec(blob, 1); else if (cpu->soc_ver == SVR_C292) fdt_del_sec(blob, 2); + + return 0; } #endif diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile index 25a1bc1..59ddeef 100644 --- a/board/freescale/common/Makefile +++ b/board/freescale/common/Makefile @@ -23,6 +23,7 @@ obj-$(CONFIG_FMAN_ENET) += fman.o obj-$(CONFIG_FSL_PIXIS) += pixis.o ifndef CONFIG_SPL_BUILD obj-$(CONFIG_FSL_NGPIXIS) += ngpixis.o +obj-$(CONFIG_VID) += vid.o endif obj-$(CONFIG_FSL_QIXIS) += qixis.o obj-$(CONFIG_PQ_MDS_PIB) += pq-mds-pib.o diff --git a/board/freescale/common/cds_pci_ft.c b/board/freescale/common/cds_pci_ft.c index 2e5dcdf..571dfbb 100644 --- a/board/freescale/common/cds_pci_ft.c +++ b/board/freescale/common/cds_pci_ft.c @@ -63,13 +63,14 @@ static void cds_pci_fixup(void *blob) } } -void -ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); #ifdef CONFIG_PCI ft_pci_setup(blob, bd); cds_pci_fixup(blob); #endif + + return 0; } #endif diff --git a/board/freescale/common/sys_eeprom.c b/board/freescale/common/sys_eeprom.c index c9c8eaa..5cb7570 100644 --- a/board/freescale/common/sys_eeprom.c +++ b/board/freescale/common/sys_eeprom.c @@ -90,7 +90,7 @@ static void show_eeprom(void) /* EEPROM tag ID, either CCID or NXID */ #ifdef CONFIG_SYS_I2C_EEPROM_NXID printf("ID: %c%c%c%c v%u\n", e.id[0], e.id[1], e.id[2], e.id[3], - be32_to_cpu(e.version)); + e.version); #else printf("ID: %c%c%c%c\n", e.id[0], e.id[1], e.id[2], e.id[3]); #endif @@ -485,7 +485,7 @@ int mac_read_from_eeprom(void) #ifdef CONFIG_SYS_I2C_EEPROM_NXID printf("%c%c%c%c v%u\n", e.id[0], e.id[1], e.id[2], e.id[3], - be32_to_cpu(e.version)); + e.version); #else printf("%c%c%c%c\n", e.id[0], e.id[1], e.id[2], e.id[3]); #endif diff --git a/board/freescale/common/vid.c b/board/freescale/common/vid.c new file mode 100644 index 0000000..6b8af14 --- /dev/null +++ b/board/freescale/common/vid.c @@ -0,0 +1,491 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <i2c.h> +#include <asm/immap_85xx.h> +#include "vid.h" + +DECLARE_GLOBAL_DATA_PTR; + +int __weak i2c_multiplexer_select_vid_channel(u8 channel) +{ + return 0; +} + +/* + * Compensate for a board specific voltage drop between regulator and SoC + * return a value in mV + */ +int __weak board_vdd_drop_compensation(void) +{ + return 0; +} + +/* + * Get the i2c address configuration for the IR regulator chip + * + * There are some variance in the RDB HW regarding the I2C address configuration + * for the IR regulator chip, which is likely a problem of external resistor + * accuracy. So we just check each address in a hopefully non-intrusive mode + * and use the first one that seems to work + * + * The IR chip can show up under the following addresses: + * 0x08 (Verified on T1040RDB-PA,T4240RDB-PB,X-T4240RDB-16GPA) + * 0x09 (Verified on T1040RDB-PA) + * 0x38 (Verified on T2080QDS, T2081QDS) + */ +static int find_ir_chip_on_i2c(void) +{ + int i2caddress; + int ret; + u8 byte; + int i; + const int ir_i2c_addr[] = {0x38, 0x08, 0x09}; + + /* Check all the address */ + for (i = 0; i < (sizeof(ir_i2c_addr)/sizeof(ir_i2c_addr[0])); i++) { + i2caddress = ir_i2c_addr[i]; + ret = i2c_read(i2caddress, + IR36021_MFR_ID_OFFSET, 1, (void *)&byte, + sizeof(byte)); + if ((ret >= 0) && (byte == IR36021_MFR_ID)) + return i2caddress; + } + return -1; +} + +/* Maximum loop count waiting for new voltage to take effect */ +#define MAX_LOOP_WAIT_NEW_VOL 100 +/* Maximum loop count waiting for the voltage to be stable */ +#define MAX_LOOP_WAIT_VOL_STABLE 100 +/* + * read_voltage from sensor on I2C bus + * We use average of 4 readings, waiting for WAIT_FOR_ADC before + * another reading + */ +#define NUM_READINGS 4 /* prefer to be power of 2 for efficiency */ + +/* If an INA220 chip is available, we can use it to read back the voltage + * as it may have a higher accuracy than the IR chip for the same purpose + */ +#ifdef CONFIG_VOL_MONITOR_INA220 +#define WAIT_FOR_ADC 532 /* wait for 532 microseconds for ADC */ +#define ADC_MIN_ACCURACY 4 +#else +#define WAIT_FOR_ADC 138 /* wait for 138 microseconds for ADC */ +#define ADC_MIN_ACCURACY 4 +#endif + +#ifdef CONFIG_VOL_MONITOR_INA220 +static int read_voltage_from_INA220(int i2caddress) +{ + int i, ret, voltage_read = 0; + u16 vol_mon; + u8 buf[2]; + + for (i = 0; i < NUM_READINGS; i++) { + ret = i2c_read(I2C_VOL_MONITOR_ADDR, + I2C_VOL_MONITOR_BUS_V_OFFSET, 1, + (void *)&buf, 2); + if (ret) { + printf("VID: failed to read core voltage\n"); + return ret; + } + vol_mon = (buf[0] << 8) | buf[1]; + if (vol_mon & I2C_VOL_MONITOR_BUS_V_OVF) { + printf("VID: Core voltage sensor error\n"); + return -1; + } + debug("VID: bus voltage reads 0x%04x\n", vol_mon); + /* LSB = 4mv */ + voltage_read += (vol_mon >> I2C_VOL_MONITOR_BUS_V_SHIFT) * 4; + udelay(WAIT_FOR_ADC); + } + /* calculate the average */ + voltage_read /= NUM_READINGS; + + return voltage_read; +} +#endif + +/* read voltage from IR */ +#ifdef CONFIG_VOL_MONITOR_IR36021_READ +static int read_voltage_from_IR(int i2caddress) +{ + int i, ret, voltage_read = 0; + u16 vol_mon; + u8 buf; + + for (i = 0; i < NUM_READINGS; i++) { + ret = i2c_read(i2caddress, + IR36021_LOOP1_VOUT_OFFSET, + 1, (void *)&buf, 1); + if (ret) { + printf("VID: failed to read vcpu\n"); + return ret; + } + vol_mon = buf; + if (!vol_mon) { + printf("VID: Core voltage sensor error\n"); + return -1; + } + debug("VID: bus voltage reads 0x%02x\n", vol_mon); + /* Resolution is 1/128V. We scale up here to get 1/128mV + * and divide at the end + */ + voltage_read += vol_mon * 1000; + udelay(WAIT_FOR_ADC); + } + /* Scale down to the real mV as IR resolution is 1/128V, rounding up */ + voltage_read = DIV_ROUND_UP(voltage_read, 128); + + /* calculate the average */ + voltage_read /= NUM_READINGS; + + /* Compensate for a board specific voltage drop between regulator and + * SoC before converting into an IR VID value + */ + voltage_read -= board_vdd_drop_compensation(); + + return voltage_read; +} +#endif + +static int read_voltage(int i2caddress) +{ + int voltage_read; +#ifdef CONFIG_VOL_MONITOR_INA220 + voltage_read = read_voltage_from_INA220(i2caddress); +#elif defined CONFIG_VOL_MONITOR_IR36021_READ + voltage_read = read_voltage_from_IR(i2caddress); +#else + return -1; +#endif + return voltage_read; +} + +/* + * We need to calculate how long before the voltage stops to drop + * or increase. It returns with the loop count. Each loop takes + * several readings (WAIT_FOR_ADC) + */ +static int wait_for_new_voltage(int vdd, int i2caddress) +{ + int timeout, vdd_current; + + vdd_current = read_voltage(i2caddress); + /* wait until voltage starts to reach the target. Voltage slew + * rates by typical regulators will always lead to stable readings + * within each fairly long ADC interval in comparison to the + * intended voltage delta change until the target voltage is + * reached. The fairly small voltage delta change to any target + * VID voltage also means that this function will always complete + * within few iterations. If the timeout was ever reached, it would + * point to a serious failure in the regulator system. + */ + for (timeout = 0; + abs(vdd - vdd_current) > (IR_VDD_STEP_UP + IR_VDD_STEP_DOWN) && + timeout < MAX_LOOP_WAIT_NEW_VOL; timeout++) { + vdd_current = read_voltage(i2caddress); + } + if (timeout >= MAX_LOOP_WAIT_NEW_VOL) { + printf("VID: Voltage adjustment timeout\n"); + return -1; + } + return timeout; +} + +/* + * this function keeps reading the voltage until it is stable or until the + * timeout expires + */ +static int wait_for_voltage_stable(int i2caddress) +{ + int timeout, vdd_current, vdd; + + vdd = read_voltage(i2caddress); + udelay(NUM_READINGS * WAIT_FOR_ADC); + + /* wait until voltage is stable */ + vdd_current = read_voltage(i2caddress); + /* The maximum timeout is + * MAX_LOOP_WAIT_VOL_STABLE * NUM_READINGS * WAIT_FOR_ADC + */ + for (timeout = MAX_LOOP_WAIT_VOL_STABLE; + abs(vdd - vdd_current) > ADC_MIN_ACCURACY && + timeout > 0; timeout--) { + vdd = vdd_current; + udelay(NUM_READINGS * WAIT_FOR_ADC); + vdd_current = read_voltage(i2caddress); + } + if (timeout == 0) + return -1; + return vdd_current; +} + +#ifdef CONFIG_VOL_MONITOR_IR36021_SET +/* Set the voltage to the IR chip */ +static int set_voltage_to_IR(int i2caddress, int vdd) +{ + int wait, vdd_last; + int ret; + u8 vid; + + /* Compensate for a board specific voltage drop between regulator and + * SoC before converting into an IR VID value + */ + vdd += board_vdd_drop_compensation(); + vid = DIV_ROUND_UP(vdd - 245, 5); + + ret = i2c_write(i2caddress, IR36021_LOOP1_MANUAL_ID_OFFSET, + 1, (void *)&vid, sizeof(vid)); + if (ret) { + printf("VID: failed to write VID\n"); + return -1; + } + wait = wait_for_new_voltage(vdd, i2caddress); + if (wait < 0) + return -1; + debug("VID: Waited %d us\n", wait * NUM_READINGS * WAIT_FOR_ADC); + + vdd_last = wait_for_voltage_stable(i2caddress); + if (vdd_last < 0) + return -1; + debug("VID: Current voltage is %d mV\n", vdd_last); + return vdd_last; +} +#endif + +static int set_voltage(int i2caddress, int vdd) +{ + int vdd_last = -1; + +#ifdef CONFIG_VOL_MONITOR_IR36021_SET + vdd_last = set_voltage_to_IR(i2caddress, vdd); +#else + #error Specific voltage monitor must be defined +#endif + return vdd_last; +} + +int adjust_vdd(ulong vdd_override) +{ + int re_enable = disable_interrupts(); + ccsr_gur_t __iomem *gur = + (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 fusesr; + u8 vid; + int vdd_target, vdd_current, vdd_last; + int ret, i2caddress; + unsigned long vdd_string_override; + char *vdd_string; + static const uint16_t vdd[32] = { + 0, /* unused */ + 9875, /* 0.9875V */ + 9750, + 9625, + 9500, + 9375, + 9250, + 9125, + 9000, + 8875, + 8750, + 8625, + 8500, + 8375, + 8250, + 8125, + 10000, /* 1.0000V */ + 10125, + 10250, + 10375, + 10500, + 10625, + 10750, + 10875, + 11000, + 0, /* reserved */ + }; + struct vdd_drive { + u8 vid; + unsigned voltage; + }; + + ret = i2c_multiplexer_select_vid_channel(I2C_MUX_CH_VOL_MONITOR); + if (ret) { + debug("VID: I2C failed to switch channel\n"); + ret = -1; + goto exit; + } + ret = find_ir_chip_on_i2c(); + if (ret < 0) { + printf("VID: Could not find voltage regulator on I2C.\n"); + ret = -1; + goto exit; + } else { + i2caddress = ret; + debug("VID: IR Chip found on I2C address 0x%02x\n", i2caddress); + } + + /* get the voltage ID from fuse status register */ + fusesr = in_be32(&gur->dcfg_fusesr); + /* + * VID is used according to the table below + * --------------------------------------- + * | DA_V | + * |-------------------------------------| + * | 5b00000 | 5b00001-5b11110 | 5b11111 | + * ---------------+---------+-----------------+---------| + * | D | 5b00000 | NO VID | VID = DA_V | NO VID | + * | A |----------+---------+-----------------+---------| + * | _ | 5b00001 |VID = | VID = |VID = | + * | V | ~ | DA_V_ALT| DA_V_ALT | DA_A_VLT| + * | _ | 5b11110 | | | | + * | A |----------+---------+-----------------+---------| + * | L | 5b11111 | No VID | VID = DA_V | NO VID | + * | T | | | | | + * ------------------------------------------------------ + */ + vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_ALTVID_SHIFT) & + FSL_CORENET_DCFG_FUSESR_ALTVID_MASK; + if ((vid == 0) || (vid == FSL_CORENET_DCFG_FUSESR_ALTVID_MASK)) { + vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_VID_SHIFT) & + FSL_CORENET_DCFG_FUSESR_VID_MASK; + } + vdd_target = vdd[vid]; + + /* check override variable for overriding VDD */ + vdd_string = getenv(CONFIG_VID_FLS_ENV); + if (vdd_override == 0 && vdd_string && + !strict_strtoul(vdd_string, 10, &vdd_string_override)) + vdd_override = vdd_string_override; + if (vdd_override >= VDD_MV_MIN && vdd_override <= VDD_MV_MAX) { + vdd_target = vdd_override * 10; /* convert to 1/10 mV */ + debug("VDD override is %lu\n", vdd_override); + } else if (vdd_override != 0) { + printf("Invalid value.\n"); + } + if (vdd_target == 0) { + debug("VID: VID not used\n"); + ret = 0; + goto exit; + } else { + /* divide and round up by 10 to get a value in mV */ + vdd_target = DIV_ROUND_UP(vdd_target, 10); + debug("VID: vid = %d mV\n", vdd_target); + } + + /* + * Read voltage monitor to check real voltage. + */ + vdd_last = read_voltage(i2caddress); + if (vdd_last < 0) { + printf("VID: Couldn't read sensor abort VID adjustment\n"); + ret = -1; + goto exit; + } + vdd_current = vdd_last; + debug("VID: Core voltage is currently at %d mV\n", vdd_last); + /* + * Adjust voltage to at or one step above target. + * As measurements are less precise than setting the values + * we may run through dummy steps that cancel each other + * when stepping up and then down. + */ + while (vdd_last > 0 && + vdd_last < vdd_target) { + vdd_current += IR_VDD_STEP_UP; + vdd_last = set_voltage(i2caddress, vdd_current); + } + while (vdd_last > 0 && + vdd_last > vdd_target + (IR_VDD_STEP_DOWN - 1)) { + vdd_current -= IR_VDD_STEP_DOWN; + vdd_last = set_voltage(i2caddress, vdd_current); + } + + if (vdd_last > 0) + printf("VID: Core voltage after adjustment is at %d mV\n", + vdd_last); + else + ret = -1; +exit: + if (re_enable) + enable_interrupts(); + return ret; +} + +static int print_vdd(void) +{ + int vdd_last, ret, i2caddress; + + ret = i2c_multiplexer_select_vid_channel(I2C_MUX_CH_VOL_MONITOR); + if (ret) { + debug("VID : I2c failed to switch channel\n"); + return -1; + } + ret = find_ir_chip_on_i2c(); + if (ret < 0) { + printf("VID: Could not find voltage regulator on I2C.\n"); + return -1; + } else { + i2caddress = ret; + debug("VID: IR Chip found on I2C address 0x%02x\n", i2caddress); + } + + /* + * Read voltage monitor to check real voltage. + */ + vdd_last = read_voltage(i2caddress); + if (vdd_last < 0) { + printf("VID: Couldn't read sensor abort VID adjustment\n"); + return -1; + } + printf("VID: Core voltage is at %d mV\n", vdd_last); + + return 0; +} + +static int do_vdd_override(cmd_tbl_t *cmdtp, + int flag, int argc, + char * const argv[]) +{ + ulong override; + + if (argc < 2) + return CMD_RET_USAGE; + + if (!strict_strtoul(argv[1], 10, &override)) + adjust_vdd(override); /* the value is checked by callee */ + else + return CMD_RET_USAGE; + return 0; +} + +static int do_vdd_read(cmd_tbl_t *cmdtp, + int flag, int argc, + char * const argv[]) +{ + if (argc < 1) + return CMD_RET_USAGE; + print_vdd(); + + return 0; +} + +U_BOOT_CMD( + vdd_override, 2, 0, do_vdd_override, + "override VDD", + " - override with the voltage specified in mV, eg. 1050" +); + +U_BOOT_CMD( + vdd_read, 1, 0, do_vdd_read, + "read VDD", + " - Read the voltage specified in mV" +) diff --git a/board/freescale/common/vid.h b/board/freescale/common/vid.h new file mode 100644 index 0000000..a9c7bb4 --- /dev/null +++ b/board/freescale/common/vid.h @@ -0,0 +1,20 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __VID_H_ +#define __VID_H_ + +#define IR36021_LOOP1_MANUAL_ID_OFFSET 0x6A +#define IR36021_LOOP1_VOUT_OFFSET 0x9A +#define IR36021_MFR_ID_OFFSET 0x92 +#define IR36021_MFR_ID 0x43 + +/* step the IR regulator in 5mV increments */ +#define IR_VDD_STEP_DOWN 5 +#define IR_VDD_STEP_UP 5 +int adjust_vdd(ulong vdd_override); + +#endif /* __VID_H_ */ diff --git a/board/freescale/common/vsc3316_3308.c b/board/freescale/common/vsc3316_3308.c index 97a25e8..dd9c37e 100644 --- a/board/freescale/common/vsc3316_3308.c +++ b/board/freescale/common/vsc3316_3308.c @@ -13,7 +13,12 @@ #define INPUT_STATE_REG 0x13 #define GLOBAL_INPUT_ISE1 0x51 #define GLOBAL_INPUT_ISE2 0x52 +#define GLOBAL_INPUT_GAIN 0x53 #define GLOBAL_INPUT_LOS 0x55 +#define GLOBAL_OUTPUT_PE1 0x56 +#define GLOBAL_OUTPUT_PE2 0x57 +#define GLOBAL_OUTPUT_LEVEL 0x58 +#define GLOBAL_OUTPUT_TERMINATION 0x5A #define GLOBAL_CORE_CNTRL 0x5D #define OUTPUT_MODE_PAGE 0x23 #define CORE_CONTROL_PAGE 0x25 @@ -92,6 +97,109 @@ int vsc3316_config(unsigned int vsc_addr, int8_t con_arr[][2], return 0; } +#ifdef CONFIG_SYS_FSL_B4860QDS_XFI_ERR +int vsc3308_config_adjust(unsigned int vsc_addr, const int8_t con_arr[][2], + unsigned int num_con) +{ + unsigned int i; + u8 rev_id = 0; + int ret; + + debug("VSC:Initializing VSC3308 at I2C address 0x%x for Tx\n", + vsc_addr); + + ret = i2c_read(vsc_addr, REVISION_ID_REG, 1, &rev_id, 1); + if (ret < 0) { + printf("VSC:0x%x could not read REV_ID from device.\n", + vsc_addr); + return ret; + } + + if (rev_id != 0xab) { + printf("VSC: device at address 0x%x is not VSC3316/3308.\n", + vsc_addr); + return -ENODEV; + } + + ret = vsc_if_enable(vsc_addr); + if (ret) { + printf("VSC:0x%x could not configured for 2-wire I/F.\n", + vsc_addr); + return ret; + } + + /* config connections - page 0x00 */ + i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, CONNECTION_CONFIG_PAGE); + + /* Configure Global Input ISE */ + i2c_reg_write(vsc_addr, GLOBAL_INPUT_ISE1, 0); + i2c_reg_write(vsc_addr, GLOBAL_INPUT_ISE2, 0); + + /* Configure Tx/Rx Global Output PE1 */ + i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_PE1, 0); + + /* Configure Tx/Rx Global Output PE2 */ + i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_PE2, 0); + + /* Configure Tx/Rx Global Input GAIN */ + i2c_reg_write(vsc_addr, GLOBAL_INPUT_GAIN, 0x3F); + + /* Setting Global Input LOS threshold value */ + i2c_reg_write(vsc_addr, GLOBAL_INPUT_LOS, 0xE0); + + /* Setting Global output termination */ + i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_TERMINATION, 0); + + /* Configure Tx/Rx Global Output level */ + if (vsc_addr == VSC3308_TX_ADDRESS) + i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_LEVEL, 4); + else + i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_LEVEL, 2); + + /* Making crosspoint connections, by connecting required + * input to output */ + for (i = 0; i < num_con ; i++) + i2c_reg_write(vsc_addr, con_arr[i][1], con_arr[i][0]); + + /* input state - page 0x13 */ + i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, INPUT_STATE_REG); + /* Turning off all the required input of the switch */ + for (i = 0; i < num_con; i++) + i2c_reg_write(vsc_addr, con_arr[i][0], 1); + + /* only turn on specific Tx/Rx requested by the XFI erratum */ + if (vsc_addr == VSC3308_TX_ADDRESS) { + i2c_reg_write(vsc_addr, 2, 0); + i2c_reg_write(vsc_addr, 3, 0); + } else { + i2c_reg_write(vsc_addr, 0, 0); + i2c_reg_write(vsc_addr, 1, 0); + } + + /* config output mode - page 0x23 */ + i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, OUTPUT_MODE_PAGE); + /* Turn off the Output driver correspond to required output*/ + for (i = 0; i < num_con ; i++) + i2c_reg_write(vsc_addr, con_arr[i][1], 1); + + /* only turn on specific Tx/Rx requested by the XFI erratum */ + if (vsc_addr == VSC3308_TX_ADDRESS) { + i2c_reg_write(vsc_addr, 0, 0); + i2c_reg_write(vsc_addr, 1, 0); + } else { + i2c_reg_write(vsc_addr, 3, 0); + i2c_reg_write(vsc_addr, 4, 0); + } + + /* configure global core control register, Turn on Global core power */ + i2c_reg_write(vsc_addr, GLOBAL_CORE_CNTRL, 0); + + vsc_wp_config(vsc_addr); + + return 0; +} +#endif + int vsc3308_config(unsigned int vsc_addr, const int8_t con_arr[][2], unsigned int num_con) { diff --git a/board/freescale/common/vsc3316_3308.h b/board/freescale/common/vsc3316_3308.h index 2a49187..d722ea3 100644 --- a/board/freescale/common/vsc3316_3308.h +++ b/board/freescale/common/vsc3316_3308.h @@ -14,6 +14,10 @@ int vsc_if_enable(unsigned int vsc_addr); int vsc3316_config(unsigned int vsc_addr, int8_t con_arr[][2], unsigned int num_con); +#ifdef CONFIG_SYS_FSL_B4860QDS_XFI_ERR +int vsc3308_config_adjust(unsigned int vsc_addr, const int8_t con_arr[][2], + unsigned int num_con); +#endif int vsc3308_config(unsigned int vsc_addr, const int8_t con_arr[][2], unsigned int num_con); void vsc_wp_config(unsigned int vsc_addr); diff --git a/board/freescale/corenet_ds/corenet_ds.c b/board/freescale/corenet_ds/corenet_ds.c index 65b3867..6f0fea1 100644 --- a/board/freescale/corenet_ds/corenet_ds.c +++ b/board/freescale/corenet_ds/corenet_ds.c @@ -190,7 +190,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -213,4 +213,6 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_fman_ethernet(blob); fdt_fixup_board_enet(blob); #endif + + return 0; } diff --git a/board/freescale/corenet_ds/eth_hydra.c b/board/freescale/corenet_ds/eth_hydra.c index 35825c4..396103f 100644 --- a/board/freescale/corenet_ds/eth_hydra.c +++ b/board/freescale/corenet_ds/eth_hydra.c @@ -62,7 +62,7 @@ #ifdef CONFIG_FMAN_ENET -#define BRDCFG1_EMI1_SEL_MASK 0x70 +#define BRDCFG1_EMI1_SEL_MASK 0x78 #define BRDCFG1_EMI1_SEL_SLOT1 0x10 #define BRDCFG1_EMI1_SEL_SLOT2 0x20 #define BRDCFG1_EMI1_SEL_SLOT5 0x30 @@ -202,6 +202,8 @@ static void fdt_set_mdio_mux(void *fdt, const char *alias, u32 mux) if (!path) path = alias; + do_fixup_by_path(fdt, path, "reg", + &mux, sizeof(mux), 1); do_fixup_by_path(fdt, path, "fsl,hydra-mdio-muxval", &mux, sizeof(mux), 1); } @@ -250,11 +252,12 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, return; } - if (mux == BRDCFG1_EMI1_SEL_RGMII) { + if (mux == (BRDCFG1_EMI1_SEL_RGMII | BRDCFG1_EMI1_EN)) { /* RGMII */ /* The RGMII PHY is identified by the MAC connected to it */ sprintf(phy, "phy_rgmii_%u", port == FM1_DTSEC4 ? 0 : 1); fdt_set_phy_handle(fdt, compat, addr, phy); + return; } /* If it's not RGMII or XGMII, it must be SGMII */ diff --git a/board/freescale/ls1021aqds/ls1021aqds.c b/board/freescale/ls1021aqds/ls1021aqds.c index 5fafc85..0a7720a 100644 --- a/board/freescale/ls1021aqds/ls1021aqds.c +++ b/board/freescale/ls1021aqds/ls1021aqds.c @@ -17,6 +17,9 @@ #include "../common/qixis.h" #include "ls1021aqds_qixis.h" +#ifdef CONFIG_U_QE +#include "../../../drivers/qe/qe.h" +#endif DECLARE_GLOBAL_DATA_PTR; @@ -137,9 +140,8 @@ int board_early_init_f(void) struct ccsr_cci400 *cci = (struct ccsr_cci400 *)CONFIG_SYS_CCI400_ADDR; #ifdef CONFIG_TSEC_ENET - out_be32(&scfg->scfgrevcr, SCFG_SCFGREVCR_REV); out_be32(&scfg->etsecdmamcr, SCFG_ETSECDMAMCR_LE_BD_FR); - out_be32(&scfg->scfgrevcr, SCFG_SCFGREVCR_NOREV); + out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125); #endif #ifdef CONFIG_FSL_IFC @@ -230,6 +232,13 @@ int board_init(void) /* Set CCI-400 control override register to * enable barrier transaction */ out_le32(&cci->ctrl_ord, CCI400_CTRLORD_EN_BARRIER); + /* + * Set CCI-400 Slave interface S0, S1, S2 Shareable Override Register + * All transactions are treated as non-shareable + */ + out_le32(&cci->slave[0].sha_ord, CCI400_SHAORD_NON_SHAREABLE); + out_le32(&cci->slave[1].sha_ord, CCI400_SHAORD_NON_SHAREABLE); + out_le32(&cci->slave[2].sha_ord, CCI400_SHAORD_NON_SHAREABLE); select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT); @@ -237,12 +246,19 @@ int board_init(void) fsl_serdes_init(); config_serdes_mux(); #endif + +#ifdef CONFIG_U_QE + u_qe_init(); +#endif + return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); + + return 0; } u8 flash_read8(void *addr) diff --git a/board/freescale/ls1021atwr/ls1021atwr.c b/board/freescale/ls1021atwr/ls1021atwr.c index 50d5640..3e8c37b 100644 --- a/board/freescale/ls1021atwr/ls1021atwr.c +++ b/board/freescale/ls1021atwr/ls1021atwr.c @@ -17,6 +17,10 @@ #include <fsl_mdio.h> #include <tsec.h> #include <fsl_sec.h> +#ifdef CONFIG_U_QE +#include "../../../drivers/qe/qe.h" +#endif + DECLARE_GLOBAL_DATA_PTR; @@ -251,11 +255,8 @@ int board_early_init_f(void) struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR; #ifdef CONFIG_TSEC_ENET - out_be32(&scfg->scfgrevcr, SCFG_SCFGREVCR_REV); out_be32(&scfg->etsecdmamcr, SCFG_ETSECDMAMCR_LE_BD_FR); out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125); - udelay(10); - out_be32(&scfg->scfgrevcr, SCFG_SCFGREVCR_NOREV); #endif #ifdef CONFIG_FSL_IFC @@ -263,9 +264,7 @@ int board_early_init_f(void) #endif #ifdef CONFIG_FSL_DCU_FB - out_be32(&scfg->scfgrevcr, SCFG_SCFGREVCR_REV); out_be32(&scfg->pixclkcr, SCFG_PIXCLKCR_PXCKEN); - out_be32(&scfg->scfgrevcr, SCFG_SCFGREVCR_NOREV); #endif return 0; @@ -273,11 +272,25 @@ int board_early_init_f(void) int board_init(void) { + struct ccsr_cci400 *cci = (struct ccsr_cci400 *)CONFIG_SYS_CCI400_ADDR; + + /* + * Set CCI-400 Slave interface S0, S1, S2 Shareable Override Register + * All transactions are treated as non-shareable + */ + out_le32(&cci->slave[0].sha_ord, CCI400_SHAORD_NON_SHAREABLE); + out_le32(&cci->slave[1].sha_ord, CCI400_SHAORD_NON_SHAREABLE); + out_le32(&cci->slave[2].sha_ord, CCI400_SHAORD_NON_SHAREABLE); + #ifndef CONFIG_SYS_FSL_NO_SERDES fsl_serdes_init(); config_serdes_mux(); #endif +#ifdef CONFIG_U_QE + u_qe_init(); +#endif + return 0; } @@ -290,9 +303,11 @@ int misc_init_r(void) } #endif -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); + + return 0; } u8 flash_read8(void *addr) diff --git a/board/freescale/ls2085a/ls2085a.c b/board/freescale/ls2085a/ls2085a.c index 2c79a71..163a4c4 100644 --- a/board/freescale/ls2085a/ls2085a.c +++ b/board/freescale/ls2085a/ls2085a.c @@ -100,7 +100,7 @@ void fdt_fixup_board_enet(void *fdt) #endif #ifdef CONFIG_OF_BOARD_SETUP -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -115,5 +115,7 @@ void ft_board_setup(void *blob, bd_t *bd) #ifdef CONFIG_FSL_MC_ENET fdt_fixup_board_enet(blob); #endif + + return 0; } #endif diff --git a/board/freescale/mpc5121ads/mpc5121ads.c b/board/freescale/mpc5121ads/mpc5121ads.c index 940978e..40bd55d 100644 --- a/board/freescale/mpc5121ads/mpc5121ads.c +++ b/board/freescale/mpc5121ads/mpc5121ads.c @@ -275,8 +275,10 @@ int checkboard (void) } #if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); + + return 0; } #endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */ diff --git a/board/freescale/mpc7448hpc2/mpc7448hpc2.c b/board/freescale/mpc7448hpc2/mpc7448hpc2.c index 71b760c..11747ca 100644 --- a/board/freescale/mpc7448hpc2/mpc7448hpc2.c +++ b/board/freescale/mpc7448hpc2/mpc7448hpc2.c @@ -70,11 +70,12 @@ phys_size_t initdram (int board_type) } #if defined(CONFIG_OF_BOARD_SETUP) -void -ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); fdt_fixup_memory(blob, (u64)bd->bi_memstart, (u64)bd->bi_memsize); + + return 0; } #endif diff --git a/board/freescale/mpc8308rdb/mpc8308rdb.c b/board/freescale/mpc8308rdb/mpc8308rdb.c index fba41fe..93e1c50 100644 --- a/board/freescale/mpc8308rdb/mpc8308rdb.c +++ b/board/freescale/mpc8308rdb/mpc8308rdb.c @@ -161,11 +161,13 @@ int misc_init_r(void) return 0; } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); fdt_fixup_dr_usb(blob, bd); fdt_fixup_esdhc(blob, bd); + + return 0; } #endif diff --git a/board/freescale/mpc8313erdb/mpc8313erdb.c b/board/freescale/mpc8313erdb/mpc8313erdb.c index 69e98a5..eac193e 100644 --- a/board/freescale/mpc8313erdb/mpc8313erdb.c +++ b/board/freescale/mpc8313erdb/mpc8313erdb.c @@ -116,12 +116,14 @@ int misc_init_r(void) } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); #ifdef CONFIG_PCI ft_pci_setup(blob, bd); #endif + + return 0; } #endif #else /* CONFIG_SPL_BUILD */ diff --git a/board/freescale/mpc8315erdb/mpc8315erdb.c b/board/freescale/mpc8315erdb/mpc8315erdb.c index e6f091f..ed611c5 100644 --- a/board/freescale/mpc8315erdb/mpc8315erdb.c +++ b/board/freescale/mpc8315erdb/mpc8315erdb.c @@ -188,7 +188,7 @@ void fdt_tsec1_fixup(void *fdt, bd_t *bd) do_fixup_by_path(fdt, path, "status", disabled, sizeof(disabled), 1); } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); #ifdef CONFIG_PCI @@ -196,6 +196,8 @@ void ft_board_setup(void *blob, bd_t *bd) #endif fdt_fixup_dr_usb(blob, bd); fdt_tsec1_fixup(blob, bd); + + return 0; } #endif diff --git a/board/freescale/mpc8323erdb/mpc8323erdb.c b/board/freescale/mpc8323erdb/mpc8323erdb.c index 3dce362..0a0152a 100644 --- a/board/freescale/mpc8323erdb/mpc8323erdb.c +++ b/board/freescale/mpc8323erdb/mpc8323erdb.c @@ -172,12 +172,14 @@ void pci_init_board(void) } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); #ifdef CONFIG_PCI ft_pci_setup(blob, bd); #endif + + return 0; } #endif diff --git a/board/freescale/mpc832xemds/mpc832xemds.c b/board/freescale/mpc832xemds/mpc832xemds.c index b7ea0e4..adf4254 100644 --- a/board/freescale/mpc832xemds/mpc832xemds.c +++ b/board/freescale/mpc832xemds/mpc832xemds.c @@ -154,11 +154,13 @@ int checkboard(void) } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); #ifdef CONFIG_PCI ft_pci_setup(blob, bd); #endif + + return 0; } #endif diff --git a/board/freescale/mpc8349emds/mpc8349emds.c b/board/freescale/mpc8349emds/mpc8349emds.c index d909220..02b5040 100644 --- a/board/freescale/mpc8349emds/mpc8349emds.c +++ b/board/freescale/mpc8349emds/mpc8349emds.c @@ -273,11 +273,13 @@ void spi_cs_deactivate(struct spi_slave *slave) #endif /* CONFIG_HARD_SPI */ #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); #ifdef CONFIG_PCI ft_pci_setup(blob, bd); #endif + + return 0; } #endif diff --git a/board/freescale/mpc8349itx/mpc8349itx.c b/board/freescale/mpc8349itx/mpc8349itx.c index 803d722..22a1d99 100644 --- a/board/freescale/mpc8349itx/mpc8349itx.c +++ b/board/freescale/mpc8349itx/mpc8349itx.c @@ -378,11 +378,13 @@ int misc_init_r(void) } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); #ifdef CONFIG_PCI ft_pci_setup(blob, bd); #endif + + return 0; } #endif diff --git a/board/freescale/mpc8360emds/mpc8360emds.c b/board/freescale/mpc8360emds/mpc8360emds.c index 5ff9dff..f0a55f8 100644 --- a/board/freescale/mpc8360emds/mpc8360emds.c +++ b/board/freescale/mpc8360emds/mpc8360emds.c @@ -402,7 +402,7 @@ static void ft_board_fixup_qe_usb(void *blob, bd_t *bd) "peripheral", sizeof("peripheral"), 1); } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); #ifdef CONFIG_PCI @@ -447,5 +447,7 @@ void ft_board_setup(void *blob, bd_t *bd) #endif } } + + return 0; } #endif diff --git a/board/freescale/mpc8360erdk/mpc8360erdk.c b/board/freescale/mpc8360erdk/mpc8360erdk.c index fef230b..478f820 100644 --- a/board/freescale/mpc8360erdk/mpc8360erdk.c +++ b/board/freescale/mpc8360erdk/mpc8360erdk.c @@ -340,9 +340,11 @@ void pci_init_board(void) } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); ft_pci_setup(blob, bd); + + return 0; } #endif diff --git a/board/freescale/mpc837xemds/mpc837xemds.c b/board/freescale/mpc837xemds/mpc837xemds.c index c749e55..572913c 100644 --- a/board/freescale/mpc837xemds/mpc837xemds.c +++ b/board/freescale/mpc837xemds/mpc837xemds.c @@ -328,7 +328,7 @@ static void ft_pci_fixup(void *blob, bd_t *bd) #endif #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); ft_tsec_fixup(blob, bd); @@ -340,5 +340,7 @@ void ft_board_setup(void *blob, bd_t *bd) ft_pci_fixup(blob, bd); ft_pcie_fixup(blob, bd); #endif + + return 0; } #endif /* CONFIG_OF_BOARD_SETUP */ diff --git a/board/freescale/mpc837xerdb/mpc837xerdb.c b/board/freescale/mpc837xerdb/mpc837xerdb.c index 9afdcaf..e0a1031 100644 --- a/board/freescale/mpc837xerdb/mpc837xerdb.c +++ b/board/freescale/mpc837xerdb/mpc837xerdb.c @@ -199,7 +199,7 @@ int misc_init_r(void) #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { #ifdef CONFIG_PCI ft_pci_setup(blob, bd); @@ -207,5 +207,7 @@ void ft_board_setup(void *blob, bd_t *bd) ft_cpu_setup(blob, bd); fdt_fixup_dr_usb(blob, bd); fdt_fixup_esdhc(blob, bd); + + return 0; } #endif /* CONFIG_OF_BOARD_SETUP */ diff --git a/board/freescale/mpc8536ds/mpc8536ds.c b/board/freescale/mpc8536ds/mpc8536ds.c index 93eed59..7b0f461 100644 --- a/board/freescale/mpc8536ds/mpc8536ds.c +++ b/board/freescale/mpc8536ds/mpc8536ds.c @@ -271,7 +271,7 @@ int board_eth_init(bd_t *bis) } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); @@ -285,5 +285,6 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_dr_usb(blob, bd); #endif + return 0; } #endif diff --git a/board/freescale/mpc8540ads/mpc8540ads.c b/board/freescale/mpc8540ads/mpc8540ads.c index 93288c7..1069e2c 100644 --- a/board/freescale/mpc8540ads/mpc8540ads.c +++ b/board/freescale/mpc8540ads/mpc8540ads.c @@ -218,8 +218,7 @@ pci_init_board(void) #if defined(CONFIG_OF_BOARD_SETUP) -void -ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { int node, tmp[2]; const char *path; @@ -237,5 +236,7 @@ ft_board_setup(void *blob, bd_t *bd) } #endif } + + return 0; } #endif diff --git a/board/freescale/mpc8544ds/mpc8544ds.c b/board/freescale/mpc8544ds/mpc8544ds.c index 1b33db6..66fb228 100644 --- a/board/freescale/mpc8544ds/mpc8544ds.c +++ b/board/freescale/mpc8544ds/mpc8544ds.c @@ -305,7 +305,7 @@ int board_eth_init(bd_t *bis) } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); @@ -314,5 +314,7 @@ void ft_board_setup(void *blob, bd_t *bd) #ifdef CONFIG_FSL_SGMII_RISER fsl_sgmii_riser_fdt_fixup(blob); #endif + + return 0; } #endif diff --git a/board/freescale/mpc8560ads/mpc8560ads.c b/board/freescale/mpc8560ads/mpc8560ads.c index 7104e33..f99d639 100644 --- a/board/freescale/mpc8560ads/mpc8560ads.c +++ b/board/freescale/mpc8560ads/mpc8560ads.c @@ -438,8 +438,7 @@ pci_init_board(void) #if defined(CONFIG_OF_BOARD_SETUP) -void -ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { int node, tmp[2]; const char *path; @@ -457,5 +456,7 @@ ft_board_setup(void *blob, bd_t *bd) } #endif } + + return 0; } #endif diff --git a/board/freescale/mpc8568mds/mpc8568mds.c b/board/freescale/mpc8568mds/mpc8568mds.c index a8fdcb5..a5c5d9d 100644 --- a/board/freescale/mpc8568mds/mpc8568mds.c +++ b/board/freescale/mpc8568mds/mpc8568mds.c @@ -345,10 +345,12 @@ void pci_init_board(void) #endif /* CONFIG_PCI */ #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); FT_FSL_PCI_SETUP; + + return 0; } #endif diff --git a/board/freescale/mpc8569mds/mpc8569mds.c b/board/freescale/mpc8569mds/mpc8569mds.c index cb55e1c..836578f 100644 --- a/board/freescale/mpc8569mds/mpc8569mds.c +++ b/board/freescale/mpc8569mds/mpc8569mds.c @@ -514,7 +514,7 @@ void pci_init_board(void) #endif /* CONFIG_PCI */ #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { #if defined(CONFIG_SYS_UCC_RMII_MODE) int nodeoff, off, err; @@ -579,5 +579,7 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_board_fixup_esdhc(blob, bd); fdt_board_fixup_qe_uart(blob, bd); fdt_board_fixup_qe_usb(blob, bd); + + return 0; } #endif diff --git a/board/freescale/mpc8572ds/mpc8572ds.c b/board/freescale/mpc8572ds/mpc8572ds.c index 1bbf832..3f68cf4 100644 --- a/board/freescale/mpc8572ds/mpc8572ds.c +++ b/board/freescale/mpc8572ds/mpc8572ds.c @@ -232,7 +232,7 @@ int board_eth_init(bd_t *bis) #endif #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -249,5 +249,7 @@ void ft_board_setup(void *blob, bd_t *bd) #ifdef CONFIG_FSL_SGMII_RISER fsl_sgmii_riser_fdt_fixup(blob); #endif + + return 0; } #endif diff --git a/board/freescale/mpc8610hpcd/mpc8610hpcd.c b/board/freescale/mpc8610hpcd/mpc8610hpcd.c index d8740dd..95e398c 100644 --- a/board/freescale/mpc8610hpcd/mpc8610hpcd.c +++ b/board/freescale/mpc8610hpcd/mpc8610hpcd.c @@ -258,12 +258,13 @@ void pci_init_board(void) } #if defined(CONFIG_OF_BOARD_SETUP) -void -ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); FT_FSL_PCI_SETUP; + + return 0; } #endif diff --git a/board/freescale/mpc8641hpcn/mpc8641hpcn.c b/board/freescale/mpc8641hpcn/mpc8641hpcn.c index a58b5f9..94633b5 100644 --- a/board/freescale/mpc8641hpcn/mpc8641hpcn.c +++ b/board/freescale/mpc8641hpcn/mpc8641hpcn.c @@ -119,12 +119,11 @@ void pci_init_board(void) #if defined(CONFIG_OF_BOARD_SETUP) -void -ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { int off; u64 *tmp; - u32 *addrcells; + int addrcells; ft_cpu_setup(blob, bd); @@ -136,12 +135,13 @@ ft_board_setup(void *blob, bd_t *bd) * which is defined by the "reg" property in the soc node. */ off = fdt_path_offset(blob, "/soc8641"); - addrcells = (u32 *)fdt_getprop(blob, 0, "#address-cells", NULL); + addrcells = fdt_address_cells(blob, 0); tmp = (u64 *)fdt_getprop(blob, off, "reg", NULL); if (tmp) { u64 addr; - if (addrcells && (*addrcells == 1)) + + if (addrcells == 1) addr = *(u32 *)tmp; else addr = *tmp; @@ -152,6 +152,8 @@ ft_board_setup(void *blob, bd_t *bd) "in u-boot. This means your .dts might " "be old.\n"); } + + return 0; } #endif diff --git a/board/freescale/p1010rdb/p1010rdb.c b/board/freescale/p1010rdb/p1010rdb.c index 491b576..1cf0ab7 100644 --- a/board/freescale/p1010rdb/p1010rdb.c +++ b/board/freescale/p1010rdb/p1010rdb.c @@ -444,7 +444,7 @@ void fdt_disable_uart1(void *blob) } } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -496,6 +496,8 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_del_flexcan(blob); fdt_disable_uart1(blob); } + + return 0; } #endif diff --git a/board/freescale/p1022ds/p1022ds.c b/board/freescale/p1022ds/p1022ds.c index f5e1851..d7dd478 100644 --- a/board/freescale/p1022ds/p1022ds.c +++ b/board/freescale/p1022ds/p1022ds.c @@ -332,7 +332,7 @@ static void ft_codec_setup(void *blob, const char *compatible) } } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -356,5 +356,7 @@ void ft_board_setup(void *blob, bd_t *bd) /* Update the WM8776 node's clock frequency property */ ft_codec_setup(blob, "wlf,wm8776"); + + return 0; } #endif diff --git a/board/freescale/p1023rdb/p1023rdb.c b/board/freescale/p1023rdb/p1023rdb.c index d4d277b..56f561a 100644 --- a/board/freescale/p1023rdb/p1023rdb.c +++ b/board/freescale/p1023rdb/p1023rdb.c @@ -130,7 +130,7 @@ int board_eth_init(bd_t *bis) } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -147,5 +147,7 @@ void ft_board_setup(void *blob, bd_t *bd) #endif fdt_fixup_fman_ethernet(blob); + + return 0; } #endif diff --git a/board/freescale/p1_p2_rdb/p1_p2_rdb.c b/board/freescale/p1_p2_rdb/p1_p2_rdb.c index aba4f53..61ed466 100644 --- a/board/freescale/p1_p2_rdb/p1_p2_rdb.c +++ b/board/freescale/p1_p2_rdb/p1_p2_rdb.c @@ -234,7 +234,7 @@ int board_eth_init(bd_t *bis) #if defined(CONFIG_OF_BOARD_SETUP) extern void ft_pci_board_setup(void *blob); -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { const char *soc_usb_compat = "fsl-usb2-dr"; int err, usb1_off, usb2_off; @@ -263,39 +263,41 @@ void ft_board_setup(void *blob, bd_t *bd) int off = fdt_node_offset_by_compatible(blob, -1, soc_elbc_compat); if (off < 0) { - printf("WARNING: could not find compatible node" - " %s: %s.\n", soc_elbc_compat, - fdt_strerror(off)); - return; + printf("WARNING: could not find compatible node %s\n", + soc_elbc_compat); + return off; } err = fdt_del_node(blob, off); if (err < 0) { - printf("WARNING: could not remove %s: %s.\n", - soc_elbc_compat, fdt_strerror(err)); + printf("WARNING: could not remove %s\n", + soc_elbc_compat); + return err; } - return; + return 0; } #endif /* Delete USB2 node as it is muxed with eLBC */ usb1_off = fdt_node_offset_by_compatible(blob, -1, soc_usb_compat); if (usb1_off < 0) { - printf("WARNING: could not find compatible node" - " %s: %s.\n", soc_usb_compat, - fdt_strerror(usb1_off)); - return; + printf("WARNING: could not find compatible node %s\n", + soc_usb_compat); + return usb1_off; } usb2_off = fdt_node_offset_by_compatible(blob, usb1_off, soc_usb_compat); if (usb2_off < 0) { - printf("WARNING: could not find compatible node" - " %s: %s.\n", soc_usb_compat, - fdt_strerror(usb2_off)); - return; + printf("WARNING: could not find compatible node %s\n", + soc_usb_compat); + return usb2_off; } err = fdt_del_node(blob, usb2_off); - if (err < 0) - printf("WARNING: could not remove %s: %s.\n", - soc_usb_compat, fdt_strerror(err)); + if (err < 0) { + printf("WARNING: could not remove %s\n", soc_usb_compat); + return err; + } + + return 0; } + #endif diff --git a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c index a6756c6..3f47cfb 100644 --- a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c +++ b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c @@ -424,7 +424,7 @@ static void fdt_board_fixup_qe_pins(void *blob) #endif #ifdef CONFIG_OF_BOARD_SETUP -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -459,17 +459,17 @@ void ft_board_setup(void *blob, bd_t *bd) int off = fdt_node_offset_by_compatible(blob, -1, soc_elbc_compat); if (off < 0) { - printf("WARNING: could not find compatible node %s: %s.\n", - soc_elbc_compat, - fdt_strerror(off)); - return; + printf("WARNING: could not find compatible node %s\n", + soc_elbc_compat); + return off; } err = fdt_del_node(blob, off); if (err < 0) { - printf("WARNING: could not remove %s: %s.\n", - soc_elbc_compat, fdt_strerror(err)); + printf("WARNING: could not remove %s\n", + soc_elbc_compat); + return err; } - return; + return 0; } #endif @@ -477,24 +477,23 @@ void ft_board_setup(void *blob, bd_t *bd) usb1_off = fdt_node_offset_by_compatible(blob, -1, soc_usb_compat); if (usb1_off < 0) { - printf("WARNING: could not find compatible node %s: %s.\n", - soc_usb_compat, - fdt_strerror(usb1_off)); - return; + printf("WARNING: could not find compatible node %s\n", + soc_usb_compat); + return usb1_off; } usb2_off = fdt_node_offset_by_compatible(blob, usb1_off, soc_usb_compat); if (usb2_off < 0) { - printf("WARNING: could not find compatible node %s: %s.\n", - soc_usb_compat, - fdt_strerror(usb2_off)); - return; + printf("WARNING: could not find compatible node %s\n", + soc_usb_compat); + return usb2_off; } err = fdt_del_node(blob, usb2_off); if (err < 0) { - printf("WARNING: could not remove %s: %s.\n", - soc_usb_compat, fdt_strerror(err)); + printf("WARNING: could not remove %s\n", soc_usb_compat); + return err; } + return 0; } #endif diff --git a/board/freescale/p1_twr/p1_twr.c b/board/freescale/p1_twr/p1_twr.c index a0a416b..a40bea3 100644 --- a/board/freescale/p1_twr/p1_twr.c +++ b/board/freescale/p1_twr/p1_twr.c @@ -261,7 +261,7 @@ static void fdt_board_fixup_qe_pins(void *blob) #endif #ifdef CONFIG_OF_BOARD_SETUP -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -283,5 +283,7 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_board_fixup_qe_pins(blob); #endif fdt_fixup_dr_usb(blob, bd); + + return 0; } #endif diff --git a/board/freescale/p2020come/p2020come.c b/board/freescale/p2020come/p2020come.c index f777bb9..1db37e3 100644 --- a/board/freescale/p2020come/p2020come.c +++ b/board/freescale/p2020come/p2020come.c @@ -250,7 +250,7 @@ int board_eth_init(bd_t *bis) #endif #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -269,5 +269,7 @@ void ft_board_setup(void *blob, bd_t *bd) #ifdef CONFIG_HAS_FSL_DR_USB fdt_fixup_dr_usb(blob, bd); #endif + + return 0; } #endif diff --git a/board/freescale/p2020ds/p2020ds.c b/board/freescale/p2020ds/p2020ds.c index b72fcff..5d18e8d 100644 --- a/board/freescale/p2020ds/p2020ds.c +++ b/board/freescale/p2020ds/p2020ds.c @@ -236,7 +236,7 @@ int board_eth_init(bd_t *bis) #endif #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -257,5 +257,7 @@ void ft_board_setup(void *blob, bd_t *bd) #ifdef CONFIG_FSL_SGMII_RISER fsl_sgmii_riser_fdt_fixup(blob); #endif + + return 0; } #endif diff --git a/board/freescale/p2041rdb/p2041rdb.c b/board/freescale/p2041rdb/p2041rdb.c index a14b43b..e600bdb 100644 --- a/board/freescale/p2041rdb/p2041rdb.c +++ b/board/freescale/p2041rdb/p2041rdb.c @@ -215,7 +215,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -239,4 +239,6 @@ void ft_board_setup(void *blob, bd_t *bd) #ifdef CONFIG_SYS_DPAA_FMAN fdt_fixup_fman_ethernet(blob); #endif + + return 0; } diff --git a/board/freescale/qemu-ppce500/qemu-ppce500.c b/board/freescale/qemu-ppce500/qemu-ppce500.c index 230870d..a0fca0d 100644 --- a/board/freescale/qemu-ppce500/qemu-ppce500.c +++ b/board/freescale/qemu-ppce500/qemu-ppce500.c @@ -235,9 +235,11 @@ int board_eth_init(bd_t *bis) } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { FT_FSL_PCI_SETUP; + + return 0; } #endif diff --git a/board/freescale/t102xqds/Kconfig b/board/freescale/t102xqds/Kconfig new file mode 100644 index 0000000..4d17798 --- /dev/null +++ b/board/freescale/t102xqds/Kconfig @@ -0,0 +1,12 @@ +if TARGET_T102XQDS + +config SYS_BOARD + default "t102xqds" + +config SYS_VENDOR + default "freescale" + +config SYS_CONFIG_NAME + default "T102xQDS" + +endif diff --git a/board/freescale/t102xqds/MAINTAINERS b/board/freescale/t102xqds/MAINTAINERS new file mode 100644 index 0000000..1ffccc4 --- /dev/null +++ b/board/freescale/t102xqds/MAINTAINERS @@ -0,0 +1,12 @@ +T102XQDS BOARD +M: Shengzhou Liu <Shengzhou.Liu@freescale.com> +S: Maintained +F: board/freescale/t102xqds/ +F: include/configs/T102xQDS.h +F: configs/T1024QDS_defconfig +F: configs/T1024QDS_NAND_defconfig +F: configs/T1024QDS_SDCARD_defconfig +F: configs/T1024QDS_SPIFLASH_defconfig +F: configs/T1024QDS_D4_defconfig +F: configs/T1024QDS_SECURE_BOOT_defconfig +F: configs/T1024QDS_D4_SECURE_BOOT_defconfig diff --git a/board/freescale/t102xqds/Makefile b/board/freescale/t102xqds/Makefile new file mode 100644 index 0000000..d94f230 --- /dev/null +++ b/board/freescale/t102xqds/Makefile @@ -0,0 +1,17 @@ +# +# Copyright 2014 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +else +obj-y += t102xqds.o +obj-y += eth_t102xqds.o +obj-$(CONFIG_PCI) += pci.o +obj-$(CONFIG_FSL_DIU_FB) += ../t1040qds/diu.o +endif +obj-y += ddr.o +obj-y += law.o +obj-y += tlb.o diff --git a/board/freescale/t102xqds/README b/board/freescale/t102xqds/README new file mode 100644 index 0000000..bb0f280 --- /dev/null +++ b/board/freescale/t102xqds/README @@ -0,0 +1,328 @@ +T1024 SoC Overview +------------------ +The T1024/T1023 dual core and T1014/T1013 single core QorIQ communication processor +combines two or one 64-bit Power Architecture e5500 core respectively with high +performance datapath acceleration logic, and network peripheral bus interfaces +required for networking and telecommunications. This processor can be used in +applications such as enterprise WLAN access points, routers, switches, firewall +and other packet processing intensive small enterprise and branch office appliances, +and general-purpose embedded computing. Its high level of integration offers +significant performance benefits and greatly helps to simplify board design. + + +The T1024 SoC includes the following function and features: +- two e5500 cores, each with a private 256 KB L2 cache + - Up to 1.4 GHz with 64-bit ISA support (Power Architecture v2.06-compliant) + - Three levels of instructions: User, supervisor, and hypervisor + - Independent boot and reset + - Secure boot capability +- 256 KB shared L3 CoreNet platform cache (CPC) +- Interconnect CoreNet platform + - CoreNet coherency manager supporting coherent and noncoherent transactions + with prioritization and bandwidth allocation amongst CoreNet endpoints + - 150 Gbps coherent read bandwidth +- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support +- Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions: + - Packet parsing, classification, and distribution + - Queue management for scheduling, packet sequencing, and congestion management + - Cryptography Acceleration (SEC 5.x) + - IEEE 1588 support + - Hardware buffer management for buffer allocation and deallocation + - MACSEC on DPAA-based Ethernet ports +- Ethernet interfaces + - Four 1 Gbps Ethernet controllers +- Parallel Ethernet interfaces + - Two RGMII interfaces +- High speed peripheral interfaces + - Three PCI Express 2.0 controllers/ports running at up to 5 GHz + - One SATA controller supporting 1.5 and 3.0 Gb/s operation + - One QSGMII interface + - Four SGMII interface supporting 1000 Mbps + - Three SGMII interfaces supporting up to 2500 Mbps + - 10GbE XFI or 10Base-KR interface +- Additional peripheral interfaces + - Two USB 2.0 controllers with integrated PHY + - SD/eSDHC/eMMC + - eSPI controller + - Four I2C controllers + - Four UARTs + - Four GPIO controllers + - Integrated flash controller (IFC) + - LCD interface (DIU) with 12 bit dual data rate +- Multicore programmable interrupt controller (PIC) +- Two 8-channel DMA engines +- Single source clocking implementation +- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB) +- QUICC Engine block + - 32-bit RISC controller for flexible support of the communications peripherals + - Serial DMA channel for receive and transmit on all serial channels + - Two universal communication controllers, supporting TDM, HDLC, and UART + +T1023 Personality +------------------ +T1023 is a reduced personality of T1024 without QUICC Engine, DIU, and +unavailable deep sleep. Rest of the blocks are almost same as T1024. +Differences between T1024 and T1023 +Feature T1024 T1023 +QUICC Engine: yes no +DIU: yes no +Deep Sleep: yes no +I2C controller: 4 3 +DDR: 64-bit 32-bit +IFC: 32-bit 28-bit + + +T1024QDS board Overview +----------------------- +- SERDES Connections + 4 lanes supporting the following: + - PCI Express: supports Gen 1 and Gen 2 + - SGMII 1G and SGMII 2.5G + - QSGMII + - XFI + - SATA 2.0 + - High-speed multiplexers route the SerDes traffic to appropriate slots or connectors. + - Aurora debug with dedicated connectors. +- DDR Controller + - Supports up to 1600 MTPS data-rate. + - Supports one DDR4 or DDR3L module using DDR4 to DDR3L adapter card. + - Supports Single-, dual- or quad-rank DIMMs + - DDR power supplies 1.35V (DDR3L)/1.20V (DDR4) to all devices with automatic tracking of VTT. +- IFC/Local Bus + - NAND Flash: 8-bit, async, up to 2GB + - NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB + - NOR devices support 8 virtual banks + - Socketed to allow alternate devices + - GASIC: Simple (minimal) target within QIXIS FPGA + - PromJET rapid memory download support + - IFC Debug/Development card +- Ethernet + - Two on-board RGMII 10M/100M/1G ethernet ports. + - One QSGMII interface + - Four SGMII interface supporting 1Gbps + - Three SGMII interfaces supporting 2.5Gbps + - one 10Gbps XFI or 10Base-KR interface +- QIXIS System Logic FPGA + - Manages system power and reset sequencing. + - Manages the configurations of DUT, board, and clock for dynamic shmoo. + - Collects V-I-T data in background for code/power profiling. + - Supports legacy TMT test features (POSt, IRS, SYSCLK-synchronous assertion). + - General fault monitoring and logging. + - Powered from ATX 'standby' power supply that allows continuous operation while rest of the system is off. +- Clocks + - System and DDR clock (SYSCLK, DDRCLK). + - Switch selectable to one of 16 common settings in the interval of 64 MHz-166 MHz. + - Software programmable in 1 MHz increments from 1-200 MHz. + - SERDES clocks + - Provides clocks to SerDes blocks and slots. + - 100 MHz, 125 MHz and 156.25 MHz options. + - Spread-spectrum option for 100 MHz. +- Power Supplies + - Dedicated PMBus regulator for VDD and VDDC. + - Adjustable from 0.7V to 1.3V at 35A + - VDD can be disabled independanty from VDDC for “deep sleep”. + - DDR3L/DDR4 power supply for GVDD: 1.35 or 1.20V at up to 22A. + - VTT/MVREF automatically track operating voltage. + - Dedicated 2.5V VPP supply. + - Dedicated regulators/filters for AVDD supplies. + - Dedicated regulators for other supplies, for example OVDD, CVDD, DVDD, LVDD, POVDD, and EVDD. +- Video + - DIU supports video up to 1280x1024x32 bpp. + - Chrontel CH7201 for HDMI connection. + - TI DS90C387R for direct LCD connection. + - Raw (not encoded) video connector for testing or other encoders. +- USB + - Supports two USB 2.0 ports with integrated PHYs. + - Two type A ports with 5V@1.5A per port. + - Second port can be converted to OTG mini-AB. +- SDHC + For T1024QDS, the SDHC port connects directly to an adapter card slot that has the following features: + - upport for optional clock feedback paths. + - Support for optional high-speed voltage translation direction controls. + - Support for SD slots for: SD, SDHC (1x, 4x, 8x) and MMC. + - Support for eMMC memory devices. +- SPI + -On-board support of 3 different devices and sizes. +- Other IO + - Two Serial ports + - ProfiBus port + - Four I2C ports + + +Memory map on T1024QDS +---------------------- +Start Address End Address Description Size +0xF_FFDF_0000 0xF_FFDF_0FFF IFC - FPGA 4KB +0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB +0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB +0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB +0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB +0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB +0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB +0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB +0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB +0xF_E000_0000 0xF_E7FF_FFFF Promjet 128MB +0xF_0000_0000 0xF_003F_FFFF DCSR 4MB +0xC_2000_0000 0xC_2FFF_FFFF PCI Express 3 Mem Space 256MB +0xC_1000_0000 0xC_1FFF_FFFF PCI Express 2 Mem Space 256MB +0xC_0000_0000 0xC_0FFF_FFFF PCI Express 1 Mem Space 256MB +0x0_0000_0000 0x0_ffff_ffff DDR 4GB + + +128MB NOR Flash memory Map +-------------------------- +Start Address End Address Definition Max size +0xEFF40000 0xEFFFFFFF u-boot (current bank) 768KB +0xEFF20000 0xEFF3FFFF u-boot env (current bank) 128KB +0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB +0xEFE00000 0xEFE3FFFF QE firmware (current bank) 256KB +0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB +0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB +0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB +0xEC000000 0xEC01FFFF RCW (alt bank) 128KB +0xEBF40000 0xEBFFFFFF u-boot (alt bank) 768KB +0xEBF20000 0xEBF3FFFF u-boot env (alt bank) 128KB +0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB +0xEBE00000 0xEBE3FFFF QE firmware (alt bank) 256KB +0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB +0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 1MB +0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB +0xE8000000 0xE801FFFF RCW (current bank) 128KB + + +SerDes clock vs DIP-switch settings +----------------------------------- +SRDS_PRTCL_S1 SD1_REF_CLK1 SD1_REF_CLK2 SW4[1:4] +0x6F 100MHz 125MHz 1101 +0xD6 100MHz 100MHz 1111 +0x99 156.25MHz 100MHz 1011 + + +T1024 Clock frequency +---------------------- +BIN Core DDR Platform FMan +Bin1: 1400MHz 1600MT/s 400MHz 700MHz +Bin2: 1200MHz 1600MT/s 400MHz 600MHz +Bin3: 1000MHz 1600MT/s 400MHz 500MHz + + + +Software configurations and board settings +------------------------------------------ +1. NOR boot: + a. build NOR boot image + $ make T1024QDS_defconfig (For DDR3L, by default) + or make T1024QDS_D4_defconfig (For DDR4) + $ make + b. program u-boot.bin image to NOR flash + => tftp 1000000 u-boot.bin + => pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize + set SW1[1:8] = '00010011', SW2[1] = '1', SW6[1:4] = '0000' for NOR boot + + Switching between default bank0 and alternate bank4 on NOR flash + To change boot source to vbank4: + via software: run command 'qixis_reset altbank' in u-boot. + via DIP-switch: set SW6[1:4] = '0100' + + To change boot source to vbank0: + via software: run command 'qixis_reset' in u-boot. + via DIP-Switch: set SW6[1:4] = '0000' + +2. NAND Boot: + a. build PBL image for NAND boot + $ make T1024QDS_NAND_defconfig + $ make + b. program u-boot-with-spl-pbl.bin to NAND flash + => tftp 1000000 u-boot-with-spl-pbl.bin + => nand erase 0 $filesize + => nand write 1000000 0 $filesize + set SW1[1:8] = '10000010', SW2[1] = '0' and SW6[1:4] = '1001' for NAND boot + +3. SPI Boot: + a. build PBL image for SPI boot + $ make T1024QDS_SPIFLASH_defconfig + $ make + b. program u-boot-with-spl-pbl.bin to SPI flash + => tftp 1000000 u-boot-with-spl-pbl.bin + => sf probe 0 + => sf erase 0 f0000 + => sf write 1000000 0 $filesize + set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot + +4. SD Boot: + a. build PBL image for SD boot + $ make T1024QDS_SDCARD_defconfig + $ make + b. program u-boot-with-spl-pbl.bin to SD/MMC card + => tftp 1000000 u-boot-with-spl-pbl.bin + => mmc write 1000000 8 0x800 + => tftp 1000000 fsl_fman_ucode_t1024_xx.bin + => mmc write 1000000 0x820 80 + set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot + + +DIU/QE-TDM/SDXC settings +------------------- +a) For TDM Riser: set pin_mux=tdm in hwconfig +b) For UCC(ProfiBus): set pin_mux=ucc in hwconfig +c) For HDMI(DVI): set pin_mux=hdmi in hwconfig +d) For LCD(DFP): set pin_mux=lcd in hwconfig +e) For SDXC: set adaptor=sdxc in hwconfig + +2-stage NAND/SPI/SD boot loader +------------------------------- +PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM. +SPL further initializes DDR using SPD and environment variables +and copy u-boot(768 KB) from NAND/SPI/SD device to DDR. +Finally SPL transers control to u-boot for futher booting. + +SPL has following features: + - Executes within 256K + - No relocation required + +Run time view of SPL framework +------------------------------------------------- +|Area | Address | +------------------------------------------------- +|SecureBoot header | 0xFFFC0000 (32KB) | +------------------------------------------------- +|GD, BD | 0xFFFC8000 (4KB) | +------------------------------------------------- +|ENV | 0xFFFC9000 (8KB) | +------------------------------------------------- +|HEAP | 0xFFFCB000 (30KB) | +------------------------------------------------- +|STACK | 0xFFFD8000 (22KB) | +------------------------------------------------- +|U-boot SPL | 0xFFFD8000 (160KB) | +------------------------------------------------- + +NAND Flash memory Map on T1024QDS +------------------------------------------------------------- +Start End Definition Size +0x000000 0x0FFFFF u-boot 1MB +0x100000 0x15FFFF u-boot env 8KB +0x160000 0x17FFFF FMAN Ucode 128KB +0x180000 0x19FFFF QE Firmware 128KB + + +SD Card memory Map on T1024QDS +---------------------------------------------------- +Block #blocks Definition Size +0x008 2048 u-boot img 1MB +0x800 0016 u-boot env 8KB +0x820 0256 FMAN Ucode 128KB +0x920 0256 QE Firmware 128KB + + +SPI Flash memory Map on T1024QDS +---------------------------------------------------- +Start End Definition Size +0x000000 0x0FFFFF u-boot img 1MB +0x100000 0x101FFF u-boot env 8KB +0x110000 0x12FFFF FMAN Ucode 128KB +0x130000 0x14FFFF QE Firmware 128KB + + +For more details, please refer to T1024QDS Reference Manual and access +website www.freescale.com and Freescale QorIQ SDK Infocenter document. diff --git a/board/freescale/t102xqds/ddr.c b/board/freescale/t102xqds/ddr.c new file mode 100644 index 0000000..46fc64e --- /dev/null +++ b/board/freescale/t102xqds/ddr.c @@ -0,0 +1,170 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> +#include <hwconfig.h> +#include <asm/mmu.h> +#include <fsl_ddr_sdram.h> +#include <fsl_ddr_dimm_params.h> +#include <asm/fsl_law.h> + +DECLARE_GLOBAL_DATA_PTR; + +struct board_specific_parameters { + u32 n_ranks; + u32 datarate_mhz_high; + u32 rank_gb; + u32 clk_adjust; + u32 wrlvl_start; + u32 wrlvl_ctl_2; + u32 wrlvl_ctl_3; +}; + +/* + * datarate_mhz_high values need to be in ascending order + */ +static const struct board_specific_parameters udimm0[] = { + /* + * memory controller 0 + * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | + * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | + */ +#if defined(CONFIG_SYS_FSL_DDR4) + {2, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A,}, + {2, 1900, 0, 4, 6, 0x08080A0C, 0x0D0E0F0A,}, + {1, 1666, 0, 4, 6, 0x0708090B, 0x0C0D0E09,}, + {1, 1900, 0, 4, 6, 0x08080A0C, 0x0D0E0F0A,}, + {1, 2200, 0, 4, 7, 0x08090A0D, 0x0F0F100C,}, +#elif defined(CONFIG_SYS_FSL_DDR3) + {2, 833, 0, 4, 6, 0x06060607, 0x08080807,}, + {2, 1350, 0, 4, 7, 0x0708080A, 0x0A0B0C09,}, + {2, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A,}, + {1, 833, 0, 4, 6, 0x06060607, 0x08080807,}, + {1, 1350, 0, 4, 7, 0x0708080A, 0x0A0B0C09,}, + {1, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A,}, +#else +#error DDR type not defined +#endif + {} +}; + +static const struct board_specific_parameters *udimms[] = { + udimm0, +}; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; + ulong ddr_freq; + struct cpu_type *cpu = gd->arch.cpu; + + if (ctrl_num > 2) { + printf("Not supported controller number %d\n", ctrl_num); + return; + } + if (!pdimm->n_ranks) + return; + + pbsp = udimms[0]; + + /* Get clk_adjust according to the board ddr freqency and n_banks + * specified in board_specific_parameters table. + */ + ddr_freq = get_ddr_freq(0) / 1000000; + while (pbsp->datarate_mhz_high) { + if (pbsp->n_ranks == pdimm->n_ranks && + (pdimm->rank_density >> 30) >= pbsp->rank_gb) { + if (ddr_freq <= pbsp->datarate_mhz_high) { + popts->clk_adjust = pbsp->clk_adjust; + popts->wrlvl_start = pbsp->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + goto found; + } + pbsp_highest = pbsp; + } + pbsp++; + } + + if (pbsp_highest) { + printf("Error: board specific timing not found\n"); + printf("for data rate %lu MT/s\n", ddr_freq); + printf("Trying to use the highest speed (%u) parameters\n", + pbsp_highest->datarate_mhz_high); + popts->clk_adjust = pbsp_highest->clk_adjust; + popts->wrlvl_start = pbsp_highest->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + } else { + panic("DIMM is not supported by this board"); + } +found: + debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n", + pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb); + debug("\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, ", + pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2); + debug("wrlvl_ctrl_3 0x%x\n", pbsp->wrlvl_ctl_3); + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 1; + /* + * Write leveling override + */ + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + + /* + * rtt and rtt_wr override + */ + popts->rtt_override = 0; + + /* Enable ZQ calibration */ + popts->zq_en = 1; + + /* DHC_EN =1, ODT = 75 Ohm */ +#ifdef CONFIG_SYS_FSL_DDR4 + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm); + popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) | + DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */ +#else + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); + popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); +#endif + + /* T1023 supports max DDR bus 32bit width, T1024 supports DDR 64bit, + * set DDR bus width to 32bit for T1023 + */ + if (cpu->soc_ver == SVR_T1023) + popts->data_bus_width = DDR_DATA_BUS_WIDTH_32; + +#ifdef CONFIG_FORCE_DDR_DATA_BUS_WIDTH_32 + /* for DDR bus 32bit test on T1024 */ + popts->data_bus_width = DDR_DATA_BUS_WIDTH_32; +#endif +} + +phys_size_t initdram(int board_type) +{ + phys_size_t dram_size; + +#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL) + puts("Initializing....using SPD\n"); + + dram_size = fsl_ddr_sdram(); + dram_size = setup_ddr_tlbs(dram_size / 0x100000); + dram_size *= 0x100000; +#else + /* DDR has been initialised by first stage boot loader */ + dram_size = fsl_ddr_sdram_size(); +#endif + return dram_size; +} diff --git a/board/freescale/t102xqds/eth_t102xqds.c b/board/freescale/t102xqds/eth_t102xqds.c new file mode 100644 index 0000000..7723f58 --- /dev/null +++ b/board/freescale/t102xqds/eth_t102xqds.c @@ -0,0 +1,442 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * Shengzhou Liu <Shengzhou.Liu@freescale.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <netdev.h> +#include <asm/mmu.h> +#include <asm/processor.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_law.h> +#include <asm/fsl_serdes.h> +#include <asm/fsl_portals.h> +#include <asm/fsl_liodn.h> +#include <malloc.h> +#include <fm_eth.h> +#include <fsl_mdio.h> +#include <miiphy.h> +#include <phy.h> +#include <asm/fsl_dtsec.h> +#include <asm/fsl_serdes.h> +#include "../common/qixis.h" +#include "../common/fman.h" +#include "t102xqds_qixis.h" + +#define EMI_NONE 0xFFFFFFFF +#define EMI1_RGMII1 0 +#define EMI1_RGMII2 1 +#define EMI1_SLOT1 2 +#define EMI1_SLOT2 3 +#define EMI1_SLOT3 4 +#define EMI1_SLOT4 5 +#define EMI1_SLOT5 6 +#define EMI2 7 + +static int mdio_mux[NUM_FM_PORTS]; + +static const char * const mdio_names[] = { + "T1024QDS_MDIO_RGMII1", + "T1024QDS_MDIO_RGMII2", + "T1024QDS_MDIO_SLOT1", + "T1024QDS_MDIO_SLOT2", + "T1024QDS_MDIO_SLOT3", + "T1024QDS_MDIO_SLOT4", + "T1024QDS_MDIO_SLOT5", + "T1024QDS_MDIO_10GC", + "NULL", +}; + +/* Map SerDes1 4 lanes to default slot, will be initialized dynamically */ +static u8 lane_to_slot[] = {2, 3, 4, 5}; + +static const char *t1024qds_mdio_name_for_muxval(u8 muxval) +{ + return mdio_names[muxval]; +} + +struct mii_dev *mii_dev_for_muxval(u8 muxval) +{ + struct mii_dev *bus; + const char *name; + + if (muxval > EMI2) + return NULL; + + name = t1024qds_mdio_name_for_muxval(muxval); + + if (!name) { + printf("No bus for muxval %x\n", muxval); + return NULL; + } + + bus = miiphy_get_dev_by_name(name); + + if (!bus) { + printf("No bus by name %s\n", name); + return NULL; + } + + return bus; +} + +struct t1024qds_mdio { + u8 muxval; + struct mii_dev *realbus; +}; + +static void t1024qds_mux_mdio(u8 muxval) +{ + u8 brdcfg4; + + if (muxval < 7) { + brdcfg4 = QIXIS_READ(brdcfg[4]); + brdcfg4 &= ~BRDCFG4_EMISEL_MASK; + brdcfg4 |= (muxval << BRDCFG4_EMISEL_SHIFT); + QIXIS_WRITE(brdcfg[4], brdcfg4); + } +} + +static int t1024qds_mdio_read(struct mii_dev *bus, int addr, int devad, + int regnum) +{ + struct t1024qds_mdio *priv = bus->priv; + + t1024qds_mux_mdio(priv->muxval); + + return priv->realbus->read(priv->realbus, addr, devad, regnum); +} + +static int t1024qds_mdio_write(struct mii_dev *bus, int addr, int devad, + int regnum, u16 value) +{ + struct t1024qds_mdio *priv = bus->priv; + + t1024qds_mux_mdio(priv->muxval); + + return priv->realbus->write(priv->realbus, addr, devad, regnum, value); +} + +static int t1024qds_mdio_reset(struct mii_dev *bus) +{ + struct t1024qds_mdio *priv = bus->priv; + + return priv->realbus->reset(priv->realbus); +} + +static int t1024qds_mdio_init(char *realbusname, u8 muxval) +{ + struct t1024qds_mdio *pmdio; + struct mii_dev *bus = mdio_alloc(); + + if (!bus) { + printf("Failed to allocate t1024qds MDIO bus\n"); + return -1; + } + + pmdio = malloc(sizeof(*pmdio)); + if (!pmdio) { + printf("Failed to allocate t1024qds private data\n"); + free(bus); + return -1; + } + + bus->read = t1024qds_mdio_read; + bus->write = t1024qds_mdio_write; + bus->reset = t1024qds_mdio_reset; + sprintf(bus->name, t1024qds_mdio_name_for_muxval(muxval)); + + pmdio->realbus = miiphy_get_dev_by_name(realbusname); + + if (!pmdio->realbus) { + printf("No bus with name %s\n", realbusname); + free(bus); + free(pmdio); + return -1; + } + + pmdio->muxval = muxval; + bus->priv = pmdio; + return mdio_register(bus); +} + +void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, + enum fm_port port, int offset) +{ + struct fixed_link f_link; + + if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_RGMII) { + if (port == FM1_DTSEC3) { + fdt_set_phy_handle(fdt, compat, addr, "rgmii_phy2"); + fdt_setprop(fdt, offset, "phy-connection-type", + "rgmii", 5); + fdt_status_okay_by_alias(fdt, "emi1_rgmii1"); + } + } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) { + if (port == FM1_DTSEC1) { + fdt_set_phy_handle(fdt, compat, addr, + "sgmii_vsc8234_phy_s5"); + } else if (port == FM1_DTSEC2) { + fdt_set_phy_handle(fdt, compat, addr, + "sgmii_vsc8234_phy_s4"); + } + } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII_2500) { + if (port == FM1_DTSEC3) { + fdt_set_phy_handle(fdt, compat, addr, + "sgmii_aqr105_phy_s3"); + } + } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_QSGMII) { + switch (port) { + case FM1_DTSEC1: + fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p1"); + break; + case FM1_DTSEC2: + fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p2"); + break; + case FM1_DTSEC3: + fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p3"); + break; + case FM1_DTSEC4: + fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p4"); + break; + default: + break; + } + fdt_delprop(fdt, offset, "phy-connection-type"); + fdt_setprop(fdt, offset, "phy-connection-type", "qsgmii", 6); + fdt_status_okay_by_alias(fdt, "emi1_slot2"); + } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII) { + /* XFI interface */ + f_link.phy_id = port; + f_link.duplex = 1; + f_link.link_speed = 10000; + f_link.pause = 0; + f_link.asym_pause = 0; + /* no PHY for XFI */ + fdt_delprop(fdt, offset, "phy-handle"); + fdt_setprop(fdt, offset, "fixed-link", &f_link, sizeof(f_link)); + fdt_setprop(fdt, offset, "phy-connection-type", "xgmii", 5); + } +} + +void fdt_fixup_board_enet(void *fdt) +{ +} + +/* + * This function reads RCW to check if Serdes1{A:D} is configured + * to slot 1/2/3/4/5 and update the lane_to_slot[] array accordingly + */ +static void initialize_lane_to_slot(void) +{ + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 srds_s1 = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS1_PRTCL; + + srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; + + switch (srds_s1) { + case 0x46: + case 0x47: + lane_to_slot[1] = 2; + break; + default: + break; + } +} + +int board_eth_init(bd_t *bis) +{ +#if defined(CONFIG_FMAN_ENET) + int i, idx, lane, slot, interface; + struct memac_mdio_info dtsec_mdio_info; + struct memac_mdio_info tgec_mdio_info; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 srds_s1; + + srds_s1 = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS1_PRTCL; + srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; + + initialize_lane_to_slot(); + + /* Initialize the mdio_mux array so we can recognize empty elements */ + for (i = 0; i < NUM_FM_PORTS; i++) + mdio_mux[i] = EMI_NONE; + + dtsec_mdio_info.regs = + (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR; + + dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME; + + /* Register the 1G MDIO bus */ + fm_memac_mdio_init(bis, &dtsec_mdio_info); + + tgec_mdio_info.regs = + (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR; + tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME; + + /* Register the 10G MDIO bus */ + fm_memac_mdio_init(bis, &tgec_mdio_info); + + /* Register the muxing front-ends to the MDIO buses */ + t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII1); + t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII2); + t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT1); + t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT2); + t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT3); + t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT4); + t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT5); + t1024qds_mdio_init(DEFAULT_FM_TGEC_MDIO_NAME, EMI2); + + /* Set the two on-board RGMII PHY address */ + fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY2_ADDR); + fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY1_ADDR); + + switch (srds_s1) { + case 0xd5: + case 0xd6: + /* QSGMII in Slot2 */ + fm_info_set_phy_address(FM1_DTSEC1, 0x8); + fm_info_set_phy_address(FM1_DTSEC2, 0x9); + fm_info_set_phy_address(FM1_DTSEC3, 0xa); + fm_info_set_phy_address(FM1_DTSEC4, 0xb); + break; + case 0x95: + case 0x99: + /* + * XFI does not need a PHY to work, but to avoid U-boot use + * default PHY address which is zero to a MAC when it found + * a MAC has no PHY address, we give a PHY address to XFI + * MAC, and should not use a real XAUI PHY address, since + * MDIO can access it successfully, and then MDIO thinks the + * XAUI card is used for the XFI MAC, which will cause error. + */ + fm_info_set_phy_address(FM1_10GEC1, 4); + fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR); + break; + case 0x6f: + /* SGMII in Slot3, Slot4, Slot5 */ + fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_AQ_PHY_ADDR_S5); + fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_AQ_PHY_ADDR_S4); + fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR); + break; + case 0x7f: + fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_AQ_PHY_ADDR_S5); + fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_AQ_PHY_ADDR_S4); + fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_AQ_PHY_ADDR_S3); + break; + case 0x47: + fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR); + break; + case 0x77: + fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_AQ_PHY_ADDR_S3); + break; + case 0x5a: + fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR); + break; + case 0x6a: + fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR); + break; + case 0x5b: + fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR); + break; + case 0x6b: + fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR); + break; + default: + break; + } + + for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { + idx = i - FM1_DTSEC1; + interface = fm_info_get_enet_if(i); + switch (interface) { + case PHY_INTERFACE_MODE_SGMII: + case PHY_INTERFACE_MODE_SGMII_2500: + case PHY_INTERFACE_MODE_QSGMII: + if (interface == PHY_INTERFACE_MODE_SGMII) { + lane = serdes_get_first_lane(FSL_SRDS_1, + SGMII_FM1_DTSEC1 + idx); + } else if (interface == PHY_INTERFACE_MODE_SGMII_2500) { + lane = serdes_get_first_lane(FSL_SRDS_1, + SGMII_2500_FM1_DTSEC1 + idx); + } else { + lane = serdes_get_first_lane(FSL_SRDS_1, + QSGMII_FM1_A); + } + + if (lane < 0) + break; + + slot = lane_to_slot[lane]; + debug("FM1@DTSEC%u expects SGMII in slot %u\n", + idx + 1, slot); + if (QIXIS_READ(present2) & (1 << (slot - 1))) + fm_disable_port(i); + + switch (slot) { + case 2: + mdio_mux[i] = EMI1_SLOT2; + fm_info_set_mdio(i, mii_dev_for_muxval( + mdio_mux[i])); + break; + case 3: + mdio_mux[i] = EMI1_SLOT3; + fm_info_set_mdio(i, mii_dev_for_muxval( + mdio_mux[i])); + break; + case 4: + mdio_mux[i] = EMI1_SLOT4; + fm_info_set_mdio(i, mii_dev_for_muxval( + mdio_mux[i])); + break; + case 5: + mdio_mux[i] = EMI1_SLOT5; + fm_info_set_mdio(i, mii_dev_for_muxval( + mdio_mux[i])); + break; + } + break; + case PHY_INTERFACE_MODE_RGMII: + if (i == FM1_DTSEC3) + mdio_mux[i] = EMI1_RGMII2; + else if (i == FM1_DTSEC4) + mdio_mux[i] = EMI1_RGMII1; + fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); + break; + default: + break; + } + } + + for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) { + idx = i - FM1_10GEC1; + switch (fm_info_get_enet_if(i)) { + case PHY_INTERFACE_MODE_XGMII: + lane = serdes_get_first_lane(FSL_SRDS_1, + XFI_FM1_MAC1 + idx); + if (lane < 0) + break; + mdio_mux[i] = EMI2; + fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); + break; + default: + break; + } + } + + cpu_eth_init(bis); +#endif /* CONFIG_FMAN_ENET */ + + return pci_eth_init(bis); +} diff --git a/board/freescale/t102xqds/law.c b/board/freescale/t102xqds/law.c new file mode 100644 index 0000000..b1c9d01 --- /dev/null +++ b/board/freescale/t102xqds/law.c @@ -0,0 +1,32 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +struct law_entry law_table[] = { +#ifndef CONFIG_SYS_NO_FLASH + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC), +#endif +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN), +#endif +#ifdef QIXIS_BASE_PHYS + SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR), +#endif +#ifdef CONFIG_SYS_NAND_BASE_PHYS + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/t102xqds/pci.c b/board/freescale/t102xqds/pci.c new file mode 100644 index 0000000..7369289 --- /dev/null +++ b/board/freescale/t102xqds/pci.c @@ -0,0 +1,23 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <pci.h> +#include <asm/fsl_pci.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <asm/fsl_serdes.h> + +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} + +void pci_of_setup(void *blob, bd_t *bd) +{ + FT_FSL_PCI_SETUP; +} diff --git a/board/freescale/t102xqds/spl.c b/board/freescale/t102xqds/spl.c new file mode 100644 index 0000000..08aef6e --- /dev/null +++ b/board/freescale/t102xqds/spl.c @@ -0,0 +1,151 @@ +/* Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <malloc.h> +#include <ns16550.h> +#include <nand.h> +#include <i2c.h> +#include <mmc.h> +#include <fsl_esdhc.h> +#include <spi_flash.h> +#include "../common/qixis.h" +#include "t102xqds_qixis.h" + +DECLARE_GLOBAL_DATA_PTR; + +phys_size_t get_effective_memsize(void) +{ + return CONFIG_SYS_L3_SIZE; +} + +unsigned long get_board_sys_clk(void) +{ + u8 sysclk_conf = QIXIS_READ(brdcfg[1]); + + switch (sysclk_conf & 0x0F) { + case QIXIS_SYSCLK_83: + return 83333333; + case QIXIS_SYSCLK_100: + return 100000000; + case QIXIS_SYSCLK_125: + return 125000000; + case QIXIS_SYSCLK_133: + return 133333333; + case QIXIS_SYSCLK_150: + return 150000000; + case QIXIS_SYSCLK_160: + return 160000000; + case QIXIS_SYSCLK_166: + return 166666666; + } + return 66666666; +} + +unsigned long get_board_ddr_clk(void) +{ + u8 ddrclk_conf = QIXIS_READ(brdcfg[1]); + + switch ((ddrclk_conf & 0x30) >> 4) { + case QIXIS_DDRCLK_100: + return 100000000; + case QIXIS_DDRCLK_125: + return 125000000; + case QIXIS_DDRCLK_133: + return 133333333; + } + return 66666666; +} + +void board_init_f(ulong bootflag) +{ + u32 plat_ratio, sys_clk, ccb_clk; + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + +#if defined(CONFIG_PPC_T1040) && defined(CONFIG_SPL_NAND_BOOT) + /* + * There is T1040 SoC issue where NOR, FPGA are inaccessible during + * NAND boot because IFC signals > IFC_AD7 are not enabled. + * This workaround changes RCW source to make all signals enabled. + */ + u32 porsr1, pinctl; +#define FSL_CORENET_CCSR_PORSR1_RCW_MASK 0xFF800000 + + porsr1 = in_be32(&gur->porsr1); + pinctl = ((porsr1 & ~(FSL_CORENET_CCSR_PORSR1_RCW_MASK)) | 0x24800000); + out_be32((unsigned int *)(CONFIG_SYS_DCSRBAR + 0x20000), pinctl); +#endif + + /* Memcpy existing GD at CONFIG_SPL_GD_ADDR */ + memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t)); + + /* Update GD pointer */ + gd = (gd_t *)(CONFIG_SPL_GD_ADDR); + + console_init_f(); + + /* initialize selected port with appropriate baud rate */ + sys_clk = get_board_sys_clk(); + plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f; + ccb_clk = sys_clk * plat_ratio / 2; + + NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, + ccb_clk / 16 / CONFIG_BAUDRATE); + +#if defined(CONFIG_SPL_MMC_BOOT) + puts("\nSD boot...\n"); +#elif defined(CONFIG_SPL_SPI_BOOT) + puts("\nSPI boot...\n"); +#elif defined(CONFIG_SPL_NAND_BOOT) + puts("\nNAND boot...\n"); +#endif + + relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0); +} + +void board_init_r(gd_t *gd, ulong dest_addr) +{ + bd_t *bd; + + bd = (bd_t *)(gd + sizeof(gd_t)); + memset(bd, 0, sizeof(bd_t)); + gd->bd = bd; + bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR; + bd->bi_memsize = CONFIG_SYS_L3_SIZE; + + probecpu(); + get_clocks(); + mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR, + CONFIG_SPL_RELOC_MALLOC_SIZE); + +#ifdef CONFIG_SPL_NAND_BOOT + nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_ENV_ADDR); +#endif +#ifdef CONFIG_SPL_MMC_BOOT + mmc_initialize(bd); + mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_ENV_ADDR); +#endif +#ifdef CONFIG_SPL_SPI_BOOT + spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_ENV_ADDR); +#endif + + gd->env_addr = (ulong)(CONFIG_ENV_ADDR); + gd->env_valid = 1; + + i2c_init_all(); + + gd->ram_size = initdram(0); + +#ifdef CONFIG_SPL_MMC_BOOT + mmc_boot(); +#elif defined(CONFIG_SPL_SPI_BOOT) + spi_boot(); +#elif defined(CONFIG_SPL_NAND_BOOT) + nand_boot(); +#endif +} diff --git a/board/freescale/t102xqds/t1024_pbi.cfg b/board/freescale/t102xqds/t1024_pbi.cfg new file mode 100644 index 0000000..7b9e9b0 --- /dev/null +++ b/board/freescale/t102xqds/t1024_pbi.cfg @@ -0,0 +1,26 @@ +#PBI commands +#Initialize CPC1 +09010000 00200400 +09138000 00000000 +091380c0 00000100 +#Configure CPC1 as 256KB SRAM +09010100 00000000 +09010104 fffc0007 +09010f00 08000000 +09010000 80000000 +#Configure LAW for CPC1 +09000cd0 00000000 +09000cd4 fffc0000 +09000cd8 81000011 +#Configure alternate space +09000010 00000000 +09000014 ff000000 +09000018 81000000 +#Configure SPI controller +09110000 80000403 +09110020 2d170008 +09110024 00100008 +09110028 00100008 +0911002c 00100008 +#Flush PBL data +091380c0 000FFFFF diff --git a/board/freescale/t102xqds/t1024_rcw.cfg b/board/freescale/t102xqds/t1024_rcw.cfg new file mode 100644 index 0000000..4b8f719 --- /dev/null +++ b/board/freescale/t102xqds/t1024_rcw.cfg @@ -0,0 +1,10 @@ +# single-source clock:Sys_Clock = DDR_Refclock = Diff_Sysclk = 100 MHz +# Core/DDR/Platform/FMan = 1400MHz/1600MT/s/400MHz/700MHz + +# PBL preamble and RCW header for T1024QDS +aa55aa55 010e0100 +# Serdes protocol 0x6F +0810000e 00000000 00000000 00000000 +37800001 00000012 e8104000 21000000 +00000000 00000000 00000000 00030810 +00000000 036c5a00 00000000 00000006 diff --git a/board/freescale/t102xqds/t102xqds.c b/board/freescale/t102xqds/t102xqds.c new file mode 100644 index 0000000..f3141b5 --- /dev/null +++ b/board/freescale/t102xqds/t102xqds.c @@ -0,0 +1,408 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <i2c.h> +#include <netdev.h> +#include <linux/compiler.h> +#include <asm/mmu.h> +#include <asm/processor.h> +#include <asm/cache.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_law.h> +#include <asm/fsl_serdes.h> +#include <asm/fsl_portals.h> +#include <asm/fsl_liodn.h> +#include <fm_eth.h> +#include <hwconfig.h> +#include <asm/mpc85xx_gpio.h> +#include "../common/qixis.h" +#include "t102xqds.h" +#include "t102xqds_qixis.h" + +DECLARE_GLOBAL_DATA_PTR; + +int checkboard(void) +{ + char buf[64]; + struct cpu_type *cpu = gd->arch.cpu; + static const char *const freq[] = {"100", "125", "156.25", "100.0"}; + int clock; + u8 sw = QIXIS_READ(arch); + + printf("Board: %sQDS, ", cpu->name); + printf("Sys ID: 0x%02x, Board Arch: V%d, ", QIXIS_READ(id), sw >> 4); + printf("Board Version: %c, boot from ", (sw & 0xf) + 'A' - 1); + +#ifdef CONFIG_SDCARD + puts("SD/MMC\n"); +#elif CONFIG_SPIFLASH + puts("SPI\n"); +#else + sw = QIXIS_READ(brdcfg[0]); + sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT; + + if (sw < 0x8) + printf("vBank: %d\n", sw); + else if (sw == 0x8) + puts("PromJet\n"); + else if (sw == 0x9) + puts("NAND\n"); + else if (sw == 0x15) + printf("IFC Card\n"); + else + printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH); +#endif + + printf("FPGA: v%d (%s), build %d", + (int)QIXIS_READ(scver), qixis_read_tag(buf), + (int)qixis_read_minor()); + /* the timestamp string contains "\n" at the end */ + printf(" on %s", qixis_read_time(buf)); + + puts("SERDES Reference: "); + sw = QIXIS_READ(brdcfg[2]); + clock = (sw >> 6) & 3; + printf("Clock1=%sMHz ", freq[clock]); + clock = (sw >> 4) & 3; + printf("Clock2=%sMHz\n", freq[clock]); + + return 0; +} + +int select_i2c_ch_pca9547(u8 ch) +{ + int ret; + + ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1); + if (ret) { + puts("PCA: failed to select proper channel\n"); + return ret; + } + + return 0; +} + +static int board_mux_lane_to_slot(void) +{ + ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 srds_prtcl_s1; + u8 brdcfg9; + + srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS1_PRTCL; + srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; + + + brdcfg9 = QIXIS_READ(brdcfg[9]); + QIXIS_WRITE(brdcfg[9], brdcfg9 | BRDCFG9_XFI_TX_DISABLE); + + switch (srds_prtcl_s1) { + case 0: + /* SerDes1 is not enabled */ + break; + case 0xd5: + case 0x5b: + case 0x6b: + case 0x77: + case 0x6f: + case 0x7f: + QIXIS_WRITE(brdcfg[12], 0x8c); + break; + case 0x40: + QIXIS_WRITE(brdcfg[12], 0xfc); + break; + case 0xd6: + case 0x5a: + case 0x6a: + case 0x56: + QIXIS_WRITE(brdcfg[12], 0x88); + break; + case 0x47: + QIXIS_WRITE(brdcfg[12], 0xcc); + break; + case 0x46: + QIXIS_WRITE(brdcfg[12], 0xc8); + break; + case 0x95: + case 0x99: + brdcfg9 &= ~BRDCFG9_XFI_TX_DISABLE; + QIXIS_WRITE(brdcfg[9], brdcfg9); + QIXIS_WRITE(brdcfg[12], 0x8c); + break; + case 0x116: + QIXIS_WRITE(brdcfg[12], 0x00); + break; + case 0x115: + case 0x119: + case 0x129: + case 0x12b: + /* Aurora, PCIe, SGMII, SATA */ + QIXIS_WRITE(brdcfg[12], 0x04); + break; + default: + printf("WARNING: unsupported for SerDes Protocol %d\n", + srds_prtcl_s1); + return -1; + } + + return 0; +} + +#ifdef CONFIG_PPC_T1024 +static void board_mux_setup(void) +{ + u8 brdcfg15; + + brdcfg15 = QIXIS_READ(brdcfg[15]); + brdcfg15 &= ~BRDCFG15_DIUSEL_MASK; + + if (hwconfig_arg_cmp("pin_mux", "tdm")) { + /* Route QE_TDM multiplexed signals to TDM Riser slot */ + QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_TDM); + QIXIS_WRITE(brdcfg[13], BRDCFG13_TDM_INTERFACE << 2); + QIXIS_WRITE(brdcfg[5], (QIXIS_READ(brdcfg[5]) & + ~BRDCFG5_SPIRTE_MASK) | BRDCFG5_SPIRTE_TDM); + } else if (hwconfig_arg_cmp("pin_mux", "ucc")) { + /* to UCC (ProfiBus) interface */ + QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_UCC); + } else if (hwconfig_arg_cmp("pin_mux", "hdmi")) { + /* to DVI (HDMI) encoder */ + QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_HDMI); + } else if (hwconfig_arg_cmp("pin_mux", "lcd")) { + /* to DFP (LCD) encoder */ + QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_LCDFM | + BRDCFG15_LCDPD | BRDCFG15_DIUSEL_LCD); + } + + if (hwconfig_arg_cmp("adaptor", "sdxc")) + /* Route SPI_CS multiplexed signals to SD slot */ + QIXIS_WRITE(brdcfg[5], (QIXIS_READ(brdcfg[5]) & + ~BRDCFG5_SPIRTE_MASK) | BRDCFG5_SPIRTE_SDHC); +} +#endif + +void board_retimer_ds125df111_init(void) +{ + u8 reg; + + /* Retimer DS125DF111 is connected to I2C1_CH7_CH5 */ + reg = I2C_MUX_CH7; + i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, ®, 1); + reg = I2C_MUX_CH5; + i2c_write(I2C_MUX_PCA_ADDR_SEC, 0, 1, ®, 1); + + /* Access to Control/Shared register */ + reg = 0x0; + i2c_write(I2C_RETIMER_ADDR, 0xff, 1, ®, 1); + + /* Read device revision and ID */ + i2c_read(I2C_RETIMER_ADDR, 1, 1, ®, 1); + debug("Retimer version id = 0x%x\n", reg); + + /* Enable Broadcast */ + reg = 0x0c; + i2c_write(I2C_RETIMER_ADDR, 0xff, 1, ®, 1); + + /* Reset Channel Registers */ + i2c_read(I2C_RETIMER_ADDR, 0, 1, ®, 1); + reg |= 0x4; + i2c_write(I2C_RETIMER_ADDR, 0, 1, ®, 1); + + /* Enable override divider select and Enable Override Output Mux */ + i2c_read(I2C_RETIMER_ADDR, 9, 1, ®, 1); + reg |= 0x24; + i2c_write(I2C_RETIMER_ADDR, 9, 1, ®, 1); + + /* Select VCO Divider to full rate (000) */ + i2c_read(I2C_RETIMER_ADDR, 0x18, 1, ®, 1); + reg &= 0x8f; + i2c_write(I2C_RETIMER_ADDR, 0x18, 1, ®, 1); + + /* Select active PFD MUX input as re-timed data (001) */ + i2c_read(I2C_RETIMER_ADDR, 0x1e, 1, ®, 1); + reg &= 0x3f; + reg |= 0x20; + i2c_write(I2C_RETIMER_ADDR, 0x1e, 1, ®, 1); + + /* Set data rate as 10.3125 Gbps */ + reg = 0x0; + i2c_write(I2C_RETIMER_ADDR, 0x60, 1, ®, 1); + reg = 0xb2; + i2c_write(I2C_RETIMER_ADDR, 0x61, 1, ®, 1); + reg = 0x90; + i2c_write(I2C_RETIMER_ADDR, 0x62, 1, ®, 1); + reg = 0xb3; + i2c_write(I2C_RETIMER_ADDR, 0x63, 1, ®, 1); + reg = 0xcd; + i2c_write(I2C_RETIMER_ADDR, 0x64, 1, ®, 1); +} + +int board_early_init_r(void) +{ +#ifdef CONFIG_SYS_FLASH_BASE + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; + int flash_esel = find_tlb_idx((void *)flashbase, 1); + + /* + * Remap Boot flash + PROMJET region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + if (flash_esel == -1) { + /* very unlikely unless something is messed up */ + puts("Error: Could not find TLB for FLASH BASE\n"); + flash_esel = 2; /* give our best effort to continue */ + } else { + /* invalidate existing TLB entry for flash + promjet */ + disable_tlb(flash_esel); + } + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel, BOOKE_PAGESZ_256M, 1); +#endif + set_liodns(); +#ifdef CONFIG_SYS_DPAA_QBMAN + setup_portals(); +#endif + select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT); + board_mux_lane_to_slot(); + board_retimer_ds125df111_init(); + + /* Increase IO drive strength to address FCS error on RGMII */ + out_be32((unsigned *)CONFIG_SYS_FSL_SCFG_IODSECR1_ADDR, 0xbfdb7800); + + return 0; +} + +unsigned long get_board_sys_clk(void) +{ + u8 sysclk_conf = QIXIS_READ(brdcfg[1]); + + switch (sysclk_conf & 0x0F) { + case QIXIS_SYSCLK_64: + return 64000000; + case QIXIS_SYSCLK_83: + return 83333333; + case QIXIS_SYSCLK_100: + return 100000000; + case QIXIS_SYSCLK_125: + return 125000000; + case QIXIS_SYSCLK_133: + return 133333333; + case QIXIS_SYSCLK_150: + return 150000000; + case QIXIS_SYSCLK_160: + return 160000000; + case QIXIS_SYSCLK_166: + return 166666666; + } + return 66666666; +} + +unsigned long get_board_ddr_clk(void) +{ + u8 ddrclk_conf = QIXIS_READ(brdcfg[1]); + + switch ((ddrclk_conf & 0x30) >> 4) { + case QIXIS_DDRCLK_100: + return 100000000; + case QIXIS_DDRCLK_125: + return 125000000; + case QIXIS_DDRCLK_133: + return 133333333; + } + return 66666666; +} + +#define NUM_SRDS_PLL 2 +int misc_init_r(void) +{ +#ifdef CONFIG_PPC_T1024 + board_mux_setup(); +#endif + return 0; +} + +void fdt_fixup_spi_mux(void *blob) +{ + int nodeoff = 0; + + if (hwconfig_arg_cmp("pin_mux", "tdm")) { + while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, + "eon,en25s64")) >= 0) { + fdt_del_node(blob, nodeoff); + } + } else { + /* remove tdm node */ + while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, + "maxim,ds26522")) >= 0) { + fdt_del_node(blob, nodeoff); + } + } +} + +int ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + +#ifdef CONFIG_PCI + pci_of_setup(blob, bd); +#endif + + fdt_fixup_liodn(blob); + +#ifdef CONFIG_HAS_FSL_DR_USB + fdt_fixup_dr_usb(blob, bd); +#endif + +#ifdef CONFIG_SYS_DPAA_FMAN + fdt_fixup_fman_ethernet(blob); + fdt_fixup_board_enet(blob); +#endif + fdt_fixup_spi_mux(blob); + + return 0; +} + +void qixis_dump_switch(void) +{ + int i, nr_of_cfgsw; + + QIXIS_WRITE(cms[0], 0x00); + nr_of_cfgsw = QIXIS_READ(cms[1]); + + puts("DIP switch settings dump:\n"); + for (i = 1; i <= nr_of_cfgsw; i++) { + QIXIS_WRITE(cms[0], i); + printf("SW%d = (0x%02x)\n", i, QIXIS_READ(cms[1])); + } +} + +#ifdef CONFIG_DEEP_SLEEP +void board_mem_sleep_setup(void) +{ + /* does not provide HW signals for power management */ + QIXIS_WRITE(pwr_ctl[1], (QIXIS_READ(pwr_ctl[1]) & ~0x2)); + /* Disable MCKE isolation */ + gpio_set_value(2, 0); + udelay(1); +} +#endif diff --git a/board/freescale/t102xqds/t102xqds.h b/board/freescale/t102xqds/t102xqds.h new file mode 100644 index 0000000..64ff623 --- /dev/null +++ b/board/freescale/t102xqds/t102xqds.h @@ -0,0 +1,14 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __T102x_QDS_H__ +#define __T102x_QDS_H__ + +void fdt_fixup_board_enet(void *blob); +void pci_of_setup(void *blob, bd_t *bd); +int select_i2c_ch_pca9547(u8 ch); + +#endif diff --git a/board/freescale/t102xqds/t102xqds_qixis.h b/board/freescale/t102xqds/t102xqds_qixis.h new file mode 100644 index 0000000..a429fb7 --- /dev/null +++ b/board/freescale/t102xqds/t102xqds_qixis.h @@ -0,0 +1,64 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __T1024QDS_QIXIS_H__ +#define __T1024QDS_QIXIS_H__ + +/* Definitions of QIXIS Registers for T1024/T1023 QDS */ + +/* BRDCFG4[4:7]] select EC1 and EC2 as a pair */ +#define BRDCFG4_EMISEL_MASK 0xE0 +#define BRDCFG4_EMISEL_SHIFT 5 + +/* BRDCFG5[0:1] controls routing and use of I2C3 & I2C4 ports*/ +#define BRDCFG5_IMX_MASK 0xC0 +#define BRDCFG5_IMX_DIU 0x80 + +#define BRDCFG5_SPIRTE_MASK 0x07 +#define BRDCFG5_SPIRTE_TDM 0x01 +#define BRDCFG5_SPIRTE_SDHC 0x02 +#define BRDCFG9_XFI_TX_DISABLE 0x10 + +/* BRDCFG13[0:5] TDM configuration and setup */ +#define BRDCFG13_TDM_MASK 0xfc +#define BRDCFG13_TDM_INTERFACE 0x37 +#define BRDCFG13_HDLC_LOOPBACK 0x29 +#define BRDCFG13_TDM_LOOPBACK 0x31 + +/* BRDCFG15[3] controls LCD Panel Powerdown */ +#define BRDCFG15_LCDFM 0x20 +#define BRDCFG15_LCDPD 0x10 +#define BRDCFG15_LCDPD_MASK 0x10 +#define BRDCFG15_LCDPD_ENABLED 0x00 + +/* BRDCFG15[6:7] controls DIU MUX selction*/ +#define BRDCFG15_DIUSEL_MASK 0x03 +#define BRDCFG15_DIUSEL_HDMI 0x00 +#define BRDCFG15_DIUSEL_LCD 0x01 +#define BRDCFG15_DIUSEL_UCC 0x02 +#define BRDCFG15_DIUSEL_TDM 0x03 + +/* SYSCLK */ +#define QIXIS_SYSCLK_66 0x0 +#define QIXIS_SYSCLK_83 0x1 +#define QIXIS_SYSCLK_100 0x2 +#define QIXIS_SYSCLK_125 0x3 +#define QIXIS_SYSCLK_133 0x4 +#define QIXIS_SYSCLK_150 0x5 +#define QIXIS_SYSCLK_160 0x6 +#define QIXIS_SYSCLK_166 0x7 +#define QIXIS_SYSCLK_64 0x8 + +/* DDRCLK */ +#define QIXIS_DDRCLK_66 0x0 +#define QIXIS_DDRCLK_100 0x1 +#define QIXIS_DDRCLK_125 0x2 +#define QIXIS_DDRCLK_133 0x3 + + +#define QIXIS_SRDS1CLK_122 0x5a +#define QIXIS_SRDS1CLK_125 0x5e +#endif diff --git a/board/freescale/t102xqds/tlb.c b/board/freescale/t102xqds/tlb.c new file mode 100644 index 0000000..409e173 --- /dev/null +++ b/board/freescale/t102xqds/tlb.c @@ -0,0 +1,117 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, + CONFIG_SYS_INIT_RAM_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ +#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) + /* + * *I*G - L3SRAM. When L3 is used as 256K SRAM, the address of the + * SRAM is at 0xfffc0000, it covered the 0xfffff000. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_256K, 1), +#else + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_4K, 1), +#endif + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_16M, 1), + + /* *I*G* - Flash, localbus */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 2, BOOKE_PAGESZ_256M, 1), + +#ifndef CONFIG_SPL_BUILD + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_1G, 1), + + /* *I*G* - PCI I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256K, 1), + + /* Bman/Qman */ +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 5, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_16M, 1), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 7, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 8, BOOKE_PAGESZ_16M, 1), +#endif +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 9, BOOKE_PAGESZ_4M, 1), +#endif +#ifdef CONFIG_SYS_NAND_BASE + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_64K, 1), +#endif +#ifdef QIXIS_BASE + SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 11, BOOKE_PAGESZ_4K, 1), +#endif + +#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD) + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 12, BOOKE_PAGESZ_1G, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000, + CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 13, BOOKE_PAGESZ_1G, 1) +#endif + /* entry 14 and 15 has been used hard coded, they will be disabled + * in cpu_init_f, so if needed more, will use entry 16 later. + */ +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/board/freescale/t102xrdb/Kconfig b/board/freescale/t102xrdb/Kconfig new file mode 100644 index 0000000..10d49f5 --- /dev/null +++ b/board/freescale/t102xrdb/Kconfig @@ -0,0 +1,12 @@ +if TARGET_T102XRDB + +config SYS_BOARD + default "t102xrdb" + +config SYS_VENDOR + default "freescale" + +config SYS_CONFIG_NAME + default "T102xRDB" + +endif diff --git a/board/freescale/t102xrdb/MAINTAINERS b/board/freescale/t102xrdb/MAINTAINERS new file mode 100644 index 0000000..dc554d4 --- /dev/null +++ b/board/freescale/t102xrdb/MAINTAINERS @@ -0,0 +1,10 @@ +T102XRDB BOARD +M: Shengzhou Liu <Shengzhou.Liu@freescale.com> +S: Maintained +F: board/freescale/t102xrdb/ +F: include/configs/T102xRDB.h +F: configs/T1024RDB_defconfig +F: configs/T1024RDB_NAND_defconfig +F: configs/T1024RDB_SDCARD_defconfig +F: configs/T1024RDB_SPIFLASH_defconfig +F: configs/T1024RDB_SECURE_BOOT_defconfig diff --git a/board/freescale/t102xrdb/Makefile b/board/freescale/t102xrdb/Makefile new file mode 100644 index 0000000..a0cf8f6 --- /dev/null +++ b/board/freescale/t102xrdb/Makefile @@ -0,0 +1,17 @@ +# +# Copyright 2014 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +else +obj-y += t102xrdb.o +obj-y += cpld.o +obj-y += eth_t102xrdb.o +obj-$(CONFIG_PCI) += pci.o +endif +obj-y += ddr.o +obj-y += law.o +obj-y += tlb.o diff --git a/board/freescale/t102xrdb/README b/board/freescale/t102xrdb/README new file mode 100644 index 0000000..2b17f50 --- /dev/null +++ b/board/freescale/t102xrdb/README @@ -0,0 +1,258 @@ +T1024 SoC Overview +------------------ +The T1024/T1023 dual core and T1014/T1013 single core QorIQ communication processor +combines two or one 64-bit Power Architecture e5500 core respectively with high +performance datapath acceleration logic, and network peripheral bus interfaces +required for networking and telecommunications. This processor can be used in +applications such as enterprise WLAN access points, routers, switches, firewall +and other packet processing intensive small enterprise and branch office appliances, +and general-purpose embedded computing. Its high level of integration offers +significant performance benefits and greatly helps to simplify board design. + + +The T1024 SoC includes the following function and features: +- two e5500 cores, each with a private 256 KB L2 cache + - Up to 1.4 GHz with 64-bit ISA support (Power Architecture v2.06-compliant) + - Three levels of instructions: User, supervisor, and hypervisor + - Independent boot and reset + - Secure boot capability +- 256 KB shared L3 CoreNet platform cache (CPC) +- Interconnect CoreNet platform + - CoreNet coherency manager supporting coherent and noncoherent transactions + with prioritization and bandwidth allocation amongst CoreNet endpoints + - 150 Gbps coherent read bandwidth +- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support +- Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions: + - Packet parsing, classification, and distribution + - Queue management for scheduling, packet sequencing, and congestion management + - Cryptography Acceleration (SEC 5.x) + - IEEE 1588 support + - Hardware buffer management for buffer allocation and deallocation + - MACSEC on DPAA-based Ethernet ports +- Ethernet interfaces + - Four 1 Gbps Ethernet controllers +- Parallel Ethernet interfaces + - Two RGMII interfaces +- High speed peripheral interfaces + - Three PCI Express 2.0 controllers/ports running at up to 5 GHz + - One SATA controller supporting 1.5 and 3.0 Gb/s operation + - One QSGMII interface + - Four SGMII interface supporting 1000 Mbps + - Three SGMII interfaces supporting up to 2500 Mbps + - 10GbE XFI or 10Base-KR interface +- Additional peripheral interfaces + - Two USB 2.0 controllers with integrated PHY + - SD/eSDHC/eMMC + - eSPI controller + - Four I2C controllers + - Four UARTs + - Four GPIO controllers + - Integrated flash controller (IFC) + - LCD interface (DIU) with 12 bit dual data rate +- Multicore programmable interrupt controller (PIC) +- Two 8-channel DMA engines +- Single source clocking implementation +- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB) +- QUICC Engine block + - 32-bit RISC controller for flexible support of the communications peripherals + - Serial DMA channel for receive and transmit on all serial channels + - Two universal communication controllers, supporting TDM, HDLC, and UART + +T1023 Personality +------------------ +T1023 is a reduced personality of T1024 without QUICC Engine, DIU, and +unavailable deep sleep. Rest of the blocks are almost same as T1024. +Differences between T1024 and T1023 +Feature T1024 T1023 +QUICC Engine: yes no +DIU: yes no +Deep Sleep: yes no +I2C controller: 4 3 +DDR: 64-bit 32-bit +IFC: 32-bit 28-bit + + +T1024RDB board Overview +----------------------- + - Ethernet + - Two on-board 10M/100M/1G bps RGMII ethernet ports + - One on-board 10G bps Base-T port. + - DDR Memory + - Supports 64-bit 4GB DDR3L DIMM + - PCIe + - One on-board PCIe slot. + - Two on-board PCIe Mini-PCIe connectors. + - IFC/Local Bus + - NOR: 128MB 16-bit NOR Flash + - NAND: 1GB 8-bit NAND flash + - CPLD: for system controlling with programable header on-board + - USB + - Supports two USB 2.0 ports with integrated PHYs + - Two type A ports with 5V@1.5A per port. + - SDHC + - one SD connector supporting 1.8V/3.3V via J53. + - SPI + - On-board 64MB SPI flash + - Other + - Two Serial ports + - Four I2C ports + + +Memory map on T1024RDB +---------------------- +Start Address End Address Description Size +0xF_FFDF_0000 0xF_FFDF_0FFF IFC - CPLD 4KB +0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB +0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB +0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB +0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB +0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB +0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB +0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB +0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB +0xF_0000_0000 0xF_003F_FFFF DCSR 4MB +0xC_2000_0000 0xC_2FFF_FFFF PCI Express 3 Mem Space 256MB +0xC_1000_0000 0xC_1FFF_FFFF PCI Express 2 Mem Space 256MB +0xC_0000_0000 0xC_0FFF_FFFF PCI Express 1 Mem Space 256MB +0x0_0000_0000 0x0_ffff_ffff DDR 4GB + + +128MB NOR Flash memory Map +-------------------------- +Start Address End Address Definition Max size +0xEFF40000 0xEFFFFFFF u-boot (current bank) 768KB +0xEFF20000 0xEFF3FFFF u-boot env (current bank) 128KB +0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB +0xEFE00000 0xEFE3FFFF QE firmware (current bank) 256KB +0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB +0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB +0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB +0xEC000000 0xEC01FFFF RCW (alt bank) 128KB +0xEBF40000 0xEBFFFFFF u-boot (alt bank) 768KB +0xEBF20000 0xEBF3FFFF u-boot env (alt bank) 128KB +0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB +0xEBE00000 0xEBE3FFFF QE firmware (alt bank) 256KB +0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB +0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 1MB +0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB +0xE8000000 0xE801FFFF RCW (current bank) 128KB + + +T1024 Clock frequency +--------------------- +BIN Core DDR Platform FMan +Bin1: 1400MHz 1600MT/s 400MHz 700MHz +Bin2: 1200MHz 1600MT/s 400MHz 600MHz +Bin3: 1000MHz 1600MT/s 400MHz 500MHz + + +Software configurations and board settings +------------------------------------------ +1. NOR boot: + a. build NOR boot image + $ make T1024RDB_defconfig + $ make + b. program u-boot.bin image to NOR flash + => tftp 1000000 u-boot.bin + => pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize + set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot + + Switching between default bank0 and alternate bank4 on NOR flash + To change boot source to vbank4: + via software: run command 'cpld reset altbank' in u-boot. + via DIP-switch: set SW3[5:7] = '100' + + To change boot source to vbank0: + via software: run command 'cpld reset' in u-boot. + via DIP-Switch: set SW3[5:7] = '000' + +2. NAND Boot: + a. build PBL image for NAND boot + $ make T1024RDB_NAND_defconfig + $ make + b. program u-boot-with-spl-pbl.bin to NAND flash + => tftp 1000000 u-boot-with-spl-pbl.bin + => nand erase 0 $filesize + => nand write 1000000 0 $filesize + set SW1[1:8] = '10001000', SW2[1] = '1', SW3[4] = '1' for NAND boot + +3. SPI Boot: + a. build PBL image for SPI boot + $ make T1024RDB_SPIFLASH_defconfig + $ make + b. program u-boot-with-spl-pbl.bin to SPI flash + => tftp 1000000 u-boot-with-spl-pbl.bin + => sf probe 0 + => sf erase 0 f0000 + => sf write 1000000 0 $filesize + set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot + +4. SD Boot: + a. build PBL image for SD boot + $ make T1024RDB_SDCARD_defconfig + $ make + b. program u-boot-with-spl-pbl.bin to SD/MMC card + => tftp 1000000 u-boot-with-spl-pbl.bin + => mmc write 1000000 8 0x800 + => tftp 1000000 fsl_fman_ucode_t1024_xx.bin + => mmc write 1000000 0x820 80 + set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot + + +2-stage NAND/SPI/SD boot loader +------------------------------- +PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM. +SPL further initializes DDR using SPD and environment variables +and copy u-boot(768 KB) from NAND/SPI/SD device to DDR. +Finally SPL transers control to u-boot for futher booting. + +SPL has following features: + - Executes within 256K + - No relocation required + +Run time view of SPL framework +------------------------------------------------- +|Area | Address | +------------------------------------------------- +|SecureBoot header | 0xFFFC0000 (32KB) | +------------------------------------------------- +|GD, BD | 0xFFFC8000 (4KB) | +------------------------------------------------- +|ENV | 0xFFFC9000 (8KB) | +------------------------------------------------- +|HEAP | 0xFFFCB000 (30KB) | +------------------------------------------------- +|STACK | 0xFFFD8000 (22KB) | +------------------------------------------------- +|U-boot SPL | 0xFFFD8000 (160KB) | +------------------------------------------------- + +NAND Flash memory Map on T1024RDB +------------------------------------------------------------- +Start End Definition Size +0x000000 0x0FFFFF u-boot 1MB(2 block) +0x100000 0x17FFFF u-boot env 512KB(1 block) +0x180000 0x1FFFFF FMAN Ucode 512KB(1 block) +0x200000 0x27FFFF QE Firmware 512KB(1 block) + + +SD Card memory Map on T1024RDB +---------------------------------------------------- +Block #blocks Definition Size +0x008 2048 u-boot img 1MB +0x800 0016 u-boot env 8KB +0x820 0256 FMAN Ucode 128KB +0x920 0256 QE Firmware 128KB + + +SPI Flash memory Map on T1024RDB +---------------------------------------------------- +Start End Definition Size +0x000000 0x0FFFFF u-boot img 1MB +0x100000 0x101FFF u-boot env 8KB +0x110000 0x12FFFF FMAN Ucode 128KB +0x130000 0x14FFFF QE Firmware 128KB + + +For more details, please refer to T1024RDB Reference Manual and access +website www.freescale.com and Freescale QorIQ SDK Infocenter document. diff --git a/board/freescale/t102xrdb/cpld.c b/board/freescale/t102xrdb/cpld.c new file mode 100644 index 0000000..c03894a --- /dev/null +++ b/board/freescale/t102xrdb/cpld.c @@ -0,0 +1,103 @@ +/** + * Copyright 2014 Freescale Semiconductor + * + * SPDX-License-Identifier: GPL-2.0+ + * + * Freescale T1024RDB board-specific CPLD controlling supports. + * + * The following macros need to be defined: + */ + +#include <common.h> +#include <command.h> +#include <asm/io.h> +#include "cpld.h" + +u8 cpld_read(unsigned int reg) +{ + void *p = (void *)CONFIG_SYS_CPLD_BASE; + + return in_8(p + reg); +} + +void cpld_write(unsigned int reg, u8 value) +{ + void *p = (void *)CONFIG_SYS_CPLD_BASE; + + out_8(p + reg, value); +} + +/** + * Set the boot bank to the alternate bank + */ +void cpld_set_altbank(void) +{ + u8 reg = CPLD_READ(flash_csr); + + reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_ALTBANK; + + CPLD_WRITE(flash_csr, reg); + CPLD_WRITE(reset_ctl1, CPLD_LBMAP_RESET); +} + +/** + * Set the boot bank to the default bank + */ +void cpld_set_defbank(void) +{ + u8 reg = CPLD_READ(flash_csr); + + reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_DFLTBANK; + + CPLD_WRITE(flash_csr, reg); + CPLD_WRITE(reset_ctl1, CPLD_LBMAP_RESET); +} + +static void cpld_dump_regs(void) +{ + printf("cpld_ver = 0x%02x\n", CPLD_READ(cpld_ver)); + printf("cpld_ver_sub = 0x%02x\n", CPLD_READ(cpld_ver_sub)); + printf("hw_ver = 0x%02x\n", CPLD_READ(hw_ver)); + printf("sw_ver = 0x%02x\n", CPLD_READ(sw_ver)); + printf("reset_ctl1 = 0x%02x\n", CPLD_READ(reset_ctl1)); + printf("reset_ctl2 = 0x%02x\n", CPLD_READ(reset_ctl2)); + printf("int_status = 0x%02x\n", CPLD_READ(int_status)); + printf("flash_csr = 0x%02x\n", CPLD_READ(flash_csr)); + printf("fan_ctl_status = 0x%02x\n", CPLD_READ(fan_ctl_status)); + printf("led_ctl_status = 0x%02x\n", CPLD_READ(led_ctl_status)); + printf("sfp_ctl_status = 0x%02x\n", CPLD_READ(sfp_ctl_status)); + printf("misc_ctl_status = 0x%02x\n", CPLD_READ(misc_ctl_status)); + printf("boot_override = 0x%02x\n", CPLD_READ(boot_override)); + printf("boot_config1 = 0x%02x\n", CPLD_READ(boot_config1)); + printf("boot_config2 = 0x%02x\n", CPLD_READ(boot_config2)); + putc('\n'); +} + +int do_cpld(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + int rc = 0; + + if (argc <= 1) + return cmd_usage(cmdtp); + + if (strcmp(argv[1], "reset") == 0) { + if (strcmp(argv[2], "altbank") == 0) + cpld_set_altbank(); + else + cpld_set_defbank(); + } else if (strcmp(argv[1], "dump") == 0) { + cpld_dump_regs(); + } else { + rc = cmd_usage(cmdtp); + } + + return rc; +} + +U_BOOT_CMD( + cpld, CONFIG_SYS_MAXARGS, 1, do_cpld, + "Reset the board or alternate bank", + "reset - hard reset to default bank\n" + "cpld reset altbank - reset to alternate bank\n" + "cpld dump - display the CPLD registers\n" + ); diff --git a/board/freescale/t102xrdb/cpld.h b/board/freescale/t102xrdb/cpld.h new file mode 100644 index 0000000..5a3100f --- /dev/null +++ b/board/freescale/t102xrdb/cpld.h @@ -0,0 +1,45 @@ +/** + * Copyright 2014 Freescale Semiconductor + * + * SPDX-License-Identifier: GPL-2.0+ + * + */ + +struct cpld_data { + u8 cpld_ver; /* 0x00 - CPLD Major Revision Register */ + u8 cpld_ver_sub; /* 0x01 - CPLD Minor Revision Register */ + u8 hw_ver; /* 0x02 - Hardware Revision Register */ + u8 sw_ver; /* 0x03 - Software Revision register */ + u8 res0[12]; /* 0x04 - 0x0F - not used */ + u8 reset_ctl1; /* 0x10 - Reset control Register1 */ + u8 reset_ctl2; /* 0x11 - Reset control Register2 */ + u8 int_status; /* 0x12 - Interrupt status Register */ + u8 flash_csr; /* 0x13 - Flash control and status register */ + u8 fan_ctl_status; /* 0x14 - Fan control and status register */ + u8 led_ctl_status; /* 0x15 - LED control and status register */ + u8 sfp_ctl_status; /* 0x16 - SFP control and status register */ + u8 misc_ctl_status; /* 0x17 - Miscellanies ctrl & status register*/ + u8 boot_override; /* 0x18 - Boot override register */ + u8 boot_config1; /* 0x19 - Boot config override register*/ + u8 boot_config2; /* 0x1A - Boot config override register*/ +} cpld_data_t; + + +/* Pointer to the CPLD register set */ + +u8 cpld_read(unsigned int reg); +void cpld_write(unsigned int reg, u8 value); + +#define CPLD_READ(reg) cpld_read(offsetof(struct cpld_data, reg)) +#define CPLD_WRITE(reg, value)\ + cpld_write(offsetof(struct cpld_data, reg), value) + +/* CPLD on IFC */ +#define CPLD_LBMAP_MASK 0x3F +#define CPLD_BANK_SEL_MASK 0x07 +#define CPLD_BANK_OVERRIDE 0x40 +#define CPLD_LBMAP_ALTBANK 0x44 /* BANK OR | BANK 4 */ +#define CPLD_LBMAP_DFLTBANK 0x40 /* BANK OR | BANK 0 */ +#define CPLD_LBMAP_RESET 0xFF +#define CPLD_LBMAP_SHIFT 0x03 +#define CPLD_BOOT_SEL 0x80 diff --git a/board/freescale/t102xrdb/ddr.c b/board/freescale/t102xrdb/ddr.c new file mode 100644 index 0000000..a20330b --- /dev/null +++ b/board/freescale/t102xrdb/ddr.c @@ -0,0 +1,154 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> +#include <hwconfig.h> +#include <asm/mmu.h> +#include <fsl_ddr_sdram.h> +#include <fsl_ddr_dimm_params.h> +#include <asm/fsl_law.h> + +DECLARE_GLOBAL_DATA_PTR; + +struct board_specific_parameters { + u32 n_ranks; + u32 datarate_mhz_high; + u32 rank_gb; + u32 clk_adjust; + u32 wrlvl_start; + u32 wrlvl_ctl_2; + u32 wrlvl_ctl_3; +}; + +/* + * datarate_mhz_high values need to be in ascending order + */ +static const struct board_specific_parameters udimm0[] = { + /* + * memory controller 0 + * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | + * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | + */ + {2, 833, 0, 4, 6, 0x06060607, 0x08080807,}, + {2, 1350, 0, 4, 7, 0x0708080A, 0x0A0B0C09,}, + {2, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A,}, + {1, 833, 0, 4, 6, 0x06060607, 0x08080807,}, + {1, 1350, 0, 4, 7, 0x0708080A, 0x0A0B0C09,}, + {1, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A,}, + {} +}; + +static const struct board_specific_parameters *udimms[] = { + udimm0, +}; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; + ulong ddr_freq; + struct cpu_type *cpu = gd->arch.cpu; + + if (ctrl_num > 1) { + printf("Not supported controller number %d\n", ctrl_num); + return; + } + if (!pdimm->n_ranks) + return; + + pbsp = udimms[0]; + + /* Get clk_adjust according to the board ddr freqency and n_banks + * specified in board_specific_parameters table. + */ + ddr_freq = get_ddr_freq(0) / 1000000; + while (pbsp->datarate_mhz_high) { + if (pbsp->n_ranks == pdimm->n_ranks && + (pdimm->rank_density >> 30) >= pbsp->rank_gb) { + if (ddr_freq <= pbsp->datarate_mhz_high) { + popts->clk_adjust = pbsp->clk_adjust; + popts->wrlvl_start = pbsp->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + goto found; + } + pbsp_highest = pbsp; + } + pbsp++; + } + + if (pbsp_highest) { + printf("Error: board specific timing not found\n"); + printf("for data rate %lu MT/s\n", ddr_freq); + printf("Trying to use the highest speed (%u) parameters\n", + pbsp_highest->datarate_mhz_high); + popts->clk_adjust = pbsp_highest->clk_adjust; + popts->wrlvl_start = pbsp_highest->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + } else { + panic("DIMM is not supported by this board"); + } +found: + debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n", + pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb); + debug("\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, ", + pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2); + debug("wrlvl_ctrl_3 0x%x\n", pbsp->wrlvl_ctl_3); + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; + /* + * Write leveling override + */ + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + + /* + * rtt and rtt_wr override + */ + popts->rtt_override = 0; + + /* Enable ZQ calibration */ + popts->zq_en = 1; + + /* DHC_EN =1, ODT = 75 Ohm */ + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_OFF); + popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_OFF); + + /* T1023 supports max DDR bus 32bit width, T1024 supports DDR 64bit, + * force DDR bus width to 32bit for T1023 + */ + if (cpu->soc_ver == SVR_T1023) + popts->data_bus_width = DDR_DATA_BUS_WIDTH_32; + +#ifdef CONFIG_FORCE_DDR_DATA_BUS_WIDTH_32 + /* for DDR bus 32bit test on T1024 */ + popts->data_bus_width = DDR_DATA_BUS_WIDTH_32; +#endif +} + +phys_size_t initdram(int board_type) +{ + phys_size_t dram_size; + +#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL) + puts("Initializing....using SPD\n"); + + dram_size = fsl_ddr_sdram(); + dram_size = setup_ddr_tlbs(dram_size / 0x100000); + dram_size *= 0x100000; +#else + /* DDR has been initialised by first stage boot loader */ + dram_size = fsl_ddr_sdram_size(); +#endif + return dram_size; +} diff --git a/board/freescale/t102xrdb/eth_t102xrdb.c b/board/freescale/t102xrdb/eth_t102xrdb.c new file mode 100644 index 0000000..2e400c4 --- /dev/null +++ b/board/freescale/t102xrdb/eth_t102xrdb.c @@ -0,0 +1,100 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <netdev.h> +#include <asm/mmu.h> +#include <asm/processor.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_law.h> +#include <asm/fsl_serdes.h> +#include <asm/fsl_portals.h> +#include <asm/fsl_liodn.h> +#include <malloc.h> +#include <fm_eth.h> +#include <fsl_mdio.h> +#include <miiphy.h> +#include <phy.h> +#include <asm/fsl_dtsec.h> +#include <asm/fsl_serdes.h> + +int board_eth_init(bd_t *bis) +{ +#if defined(CONFIG_FMAN_ENET) + int i, interface; + struct memac_mdio_info dtsec_mdio_info; + struct memac_mdio_info tgec_mdio_info; + struct mii_dev *dev; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 srds_s1; + + srds_s1 = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS1_PRTCL; + srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; + + dtsec_mdio_info.regs = + (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR; + + dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME; + + /* Register the 1G MDIO bus */ + fm_memac_mdio_init(bis, &dtsec_mdio_info); + + tgec_mdio_info.regs = + (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR; + tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME; + + /* Register the 10G MDIO bus */ + fm_memac_mdio_init(bis, &tgec_mdio_info); + + /* Set the two on-board RGMII PHY address */ + fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY2_ADDR); + fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY1_ADDR); + + switch (srds_s1) { + case 0x95: + /* 10G XFI with Aquantia PHY */ + fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR); + break; + default: + printf("SerDes protocol 0x%x is not supported on T102xRDB\n", + srds_s1); + break; + } + + for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { + interface = fm_info_get_enet_if(i); + switch (interface) { + case PHY_INTERFACE_MODE_RGMII: + dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME); + fm_info_set_mdio(i, dev); + break; + default: + break; + } + } + + for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) { + switch (fm_info_get_enet_if(i)) { + case PHY_INTERFACE_MODE_XGMII: + dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME); + fm_info_set_mdio(i, dev); + break; + default: + break; + } + } + + cpu_eth_init(bis); +#endif /* CONFIG_FMAN_ENET */ + + return pci_eth_init(bis); +} + +void fdt_fixup_board_enet(void *fdt) +{ +} diff --git a/board/freescale/t102xrdb/law.c b/board/freescale/t102xrdb/law.c new file mode 100644 index 0000000..1c9235f --- /dev/null +++ b/board/freescale/t102xrdb/law.c @@ -0,0 +1,32 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +struct law_entry law_table[] = { +#ifndef CONFIG_SYS_NO_FLASH + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC), +#endif +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN), +#endif +#ifdef CONFIG_SYS_CPLD_BASE_PHYS + SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR), +#endif +#ifdef CONFIG_SYS_NAND_BASE_PHYS + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/t102xrdb/pci.c b/board/freescale/t102xrdb/pci.c new file mode 100644 index 0000000..ba7041a --- /dev/null +++ b/board/freescale/t102xrdb/pci.c @@ -0,0 +1,23 @@ +/* + * Copyright 2007-2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <pci.h> +#include <asm/fsl_pci.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <asm/fsl_serdes.h> + +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} + +void pci_of_setup(void *blob, bd_t *bd) +{ + FT_FSL_PCI_SETUP; +} diff --git a/board/freescale/t102xrdb/spl.c b/board/freescale/t102xrdb/spl.c new file mode 100644 index 0000000..dd2dec4 --- /dev/null +++ b/board/freescale/t102xrdb/spl.c @@ -0,0 +1,107 @@ +/* Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <malloc.h> +#include <ns16550.h> +#include <nand.h> +#include <i2c.h> +#include <mmc.h> +#include <fsl_esdhc.h> +#include <spi_flash.h> + +DECLARE_GLOBAL_DATA_PTR; + +phys_size_t get_effective_memsize(void) +{ + return CONFIG_SYS_L3_SIZE; +} + +unsigned long get_board_sys_clk(void) +{ + return CONFIG_SYS_CLK_FREQ; +} + +unsigned long get_board_ddr_clk(void) +{ + return CONFIG_DDR_CLK_FREQ; +} + +void board_init_f(ulong bootflag) +{ + u32 plat_ratio, sys_clk, ccb_clk; + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + + /* Memcpy existing GD at CONFIG_SPL_GD_ADDR */ + memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t)); + + /* Update GD pointer */ + gd = (gd_t *)(CONFIG_SPL_GD_ADDR); + + console_init_f(); + + /* initialize selected port with appropriate baud rate */ + sys_clk = get_board_sys_clk(); + plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f; + ccb_clk = sys_clk * plat_ratio / 2; + + NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, + ccb_clk / 16 / CONFIG_BAUDRATE); + +#if defined(CONFIG_SPL_MMC_BOOT) + puts("\nSD boot...\n"); +#elif defined(CONFIG_SPL_SPI_BOOT) + puts("\nSPI boot...\n"); +#elif defined(CONFIG_SPL_NAND_BOOT) + puts("\nNAND boot...\n"); +#endif + + relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0); +} + +void board_init_r(gd_t *gd, ulong dest_addr) +{ + bd_t *bd; + + bd = (bd_t *)(gd + sizeof(gd_t)); + memset(bd, 0, sizeof(bd_t)); + gd->bd = bd; + bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR; + bd->bi_memsize = CONFIG_SYS_L3_SIZE; + + probecpu(); + get_clocks(); + mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR, + CONFIG_SPL_RELOC_MALLOC_SIZE); + +#ifdef CONFIG_SPL_NAND_BOOT + nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_ENV_ADDR); +#endif +#ifdef CONFIG_SPL_MMC_BOOT + mmc_initialize(bd); + mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_ENV_ADDR); +#endif +#ifdef CONFIG_SPL_SPI_BOOT + spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_ENV_ADDR); +#endif + + gd->env_addr = (ulong)(CONFIG_ENV_ADDR); + gd->env_valid = 1; + + i2c_init_all(); + + gd->ram_size = initdram(0); + +#ifdef CONFIG_SPL_MMC_BOOT + mmc_boot(); +#elif defined(CONFIG_SPL_SPI_BOOT) + spi_boot(); +#elif defined(CONFIG_SPL_NAND_BOOT) + nand_boot(); +#endif +} diff --git a/board/freescale/t102xrdb/t1024_pbi.cfg b/board/freescale/t102xrdb/t1024_pbi.cfg new file mode 100644 index 0000000..7b9e9b0 --- /dev/null +++ b/board/freescale/t102xrdb/t1024_pbi.cfg @@ -0,0 +1,26 @@ +#PBI commands +#Initialize CPC1 +09010000 00200400 +09138000 00000000 +091380c0 00000100 +#Configure CPC1 as 256KB SRAM +09010100 00000000 +09010104 fffc0007 +09010f00 08000000 +09010000 80000000 +#Configure LAW for CPC1 +09000cd0 00000000 +09000cd4 fffc0000 +09000cd8 81000011 +#Configure alternate space +09000010 00000000 +09000014 ff000000 +09000018 81000000 +#Configure SPI controller +09110000 80000403 +09110020 2d170008 +09110024 00100008 +09110028 00100008 +0911002c 00100008 +#Flush PBL data +091380c0 000FFFFF diff --git a/board/freescale/t102xrdb/t1024_rcw.cfg b/board/freescale/t102xrdb/t1024_rcw.cfg new file mode 100644 index 0000000..cd6f906 --- /dev/null +++ b/board/freescale/t102xrdb/t1024_rcw.cfg @@ -0,0 +1,8 @@ +#PBL preamble and RCW header for T1024RDB +aa55aa55 010e0100 +#SerDes Protocol: 0x95 +#Core/DDR: 1400Mhz/1600MT/s with single source clock +0810000c 00000000 00000000 00000000 +4a800003 80000012 ec027000 21000000 +00000000 00000000 00000000 00030810 +00000000 0b005a08 00000000 00000006 diff --git a/board/freescale/t102xrdb/t102xrdb.c b/board/freescale/t102xrdb/t102xrdb.c new file mode 100644 index 0000000..f5c438d --- /dev/null +++ b/board/freescale/t102xrdb/t102xrdb.c @@ -0,0 +1,144 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <i2c.h> +#include <netdev.h> +#include <linux/compiler.h> +#include <asm/mmu.h> +#include <asm/processor.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_law.h> +#include <asm/fsl_serdes.h> +#include <asm/fsl_portals.h> +#include <asm/fsl_liodn.h> +#include <asm/mpc85xx_gpio.h> +#include <fm_eth.h> +#include "t102xrdb.h" +#include "cpld.h" + +DECLARE_GLOBAL_DATA_PTR; + +int checkboard(void) +{ + struct cpu_type *cpu = gd->arch.cpu; + static const char *freq[3] = {"100.00MHZ", "125.00MHz", "156.25MHZ"}; + + printf("Board: %sRDB, ", cpu->name); + printf("Board rev: 0x%02x CPLD ver: 0x%02x, boot from ", + CPLD_READ(hw_ver), CPLD_READ(sw_ver)); + +#ifdef CONFIG_SDCARD + puts("SD/MMC\n"); +#elif CONFIG_SPIFLASH + puts("SPI\n"); +#else + u8 reg; + + reg = CPLD_READ(flash_csr); + + if (reg & CPLD_BOOT_SEL) { + puts("NAND\n"); + } else { + reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT); + printf("NOR vBank%d\n", reg); + } +#endif + + puts("SERDES Reference Clocks:\n"); + printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[2], freq[0]); + + return 0; +} + +int board_early_init_r(void) +{ +#ifdef CONFIG_SYS_FLASH_BASE + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; + int flash_esel = find_tlb_idx((void *)flashbase, 1); + /* + * Remap Boot flash region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + if (flash_esel == -1) { + /* very unlikely unless something is messed up */ + puts("Error: Could not find TLB for FLASH BASE\n"); + flash_esel = 2; /* give our best effort to continue */ + } else { + /* invalidate existing TLB entry for flash + promjet */ + disable_tlb(flash_esel); + } + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel, BOOKE_PAGESZ_256M, 1); +#endif + + set_liodns(); +#ifdef CONFIG_SYS_DPAA_QBMAN + setup_portals(); +#endif + + return 0; +} + +unsigned long get_board_sys_clk(void) +{ + return CONFIG_SYS_CLK_FREQ; +} + +unsigned long get_board_ddr_clk(void) +{ + return CONFIG_DDR_CLK_FREQ; +} + +int misc_init_r(void) +{ + return 0; +} + +int ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + +#ifdef CONFIG_PCI + pci_of_setup(blob, bd); +#endif + + fdt_fixup_liodn(blob); + fdt_fixup_dr_usb(blob, bd); + +#ifdef CONFIG_SYS_DPAA_FMAN + fdt_fixup_fman_ethernet(blob); + fdt_fixup_board_enet(blob); +#endif + + return 0; +} + +#ifdef CONFIG_DEEP_SLEEP +void board_mem_sleep_setup(void) +{ + /* does not provide HW signals for power management */ + CPLD_WRITE(misc_ctl_status, (CPLD_READ(misc_ctl_status) & ~0x40)); + /* Disable MCKE isolation */ + gpio_set_value(2, 0); + udelay(1); +} +#endif diff --git a/board/freescale/t102xrdb/t102xrdb.h b/board/freescale/t102xrdb/t102xrdb.h new file mode 100644 index 0000000..2f23579 --- /dev/null +++ b/board/freescale/t102xrdb/t102xrdb.h @@ -0,0 +1,13 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __T1024_RDB_H__ +#define __T1024_RDB_H__ + +void fdt_fixup_board_enet(void *blob); +void pci_of_setup(void *blob, bd_t *bd); + +#endif diff --git a/board/freescale/t102xrdb/tlb.c b/board/freescale/t102xrdb/tlb.c new file mode 100644 index 0000000..8269b3d --- /dev/null +++ b/board/freescale/t102xrdb/tlb.c @@ -0,0 +1,117 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, + CONFIG_SYS_INIT_RAM_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ +#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) + /* + * *I*G - L3SRAM. When L3 is used as 256K SRAM, the address of the + * SRAM is at 0xfffc0000, it covered the 0xfffff000. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_256K, 1), +#else + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_4K, 1), +#endif + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_16M, 1), + + /* *I*G* - Flash, localbus */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 2, BOOKE_PAGESZ_256M, 1), + +#ifndef CONFIG_SPL_BUILD + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_1G, 1), + + /* *I*G* - PCI I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256K, 1), + + /* Bman/Qman */ +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 5, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_16M, 1), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 7, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 8, BOOKE_PAGESZ_16M, 1), +#endif +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 9, BOOKE_PAGESZ_4M, 1), +#endif +#ifdef CONFIG_SYS_NAND_BASE + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_64K, 1), +#endif +#ifdef CONFIG_SYS_CPLD_BASE + SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 11, BOOKE_PAGESZ_256K, 1), +#endif + +#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD) + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 12, BOOKE_PAGESZ_1G, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000, + CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 13, BOOKE_PAGESZ_1G, 1) +#endif + /* entry 14 and 15 has been used hard coded, they will be disabled + * in cpu_init_f, so if needed more, will use entry 16 later. + */ +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/board/freescale/t1040qds/t1040qds.c b/board/freescale/t1040qds/t1040qds.c index 19af46e..13285be 100644 --- a/board/freescale/t1040qds/t1040qds.c +++ b/board/freescale/t1040qds/t1040qds.c @@ -233,7 +233,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -259,6 +259,8 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_fman_ethernet(blob); fdt_fixup_board_enet(blob); #endif + + return 0; } void qixis_dump_switch(void) diff --git a/board/freescale/t104xrdb/spl.c b/board/freescale/t104xrdb/spl.c index 3822a37..e394b12 100644 --- a/board/freescale/t104xrdb/spl.c +++ b/board/freescale/t104xrdb/spl.c @@ -34,20 +34,26 @@ unsigned long get_board_ddr_clk(void) void board_init_f(ulong bootflag) { u32 plat_ratio, sys_clk, uart_clk; -#ifdef CONFIG_SPL_NAND_BOOT +#if defined(CONFIG_SPL_NAND_BOOT) && defined(CONFIG_A008044_WORKAROUND) u32 porsr1, pinctl; + u32 svr = get_svr(); #endif ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; -#ifdef CONFIG_SPL_NAND_BOOT - /* - * There is T1040 SoC issue where NOR, FPGA are inaccessible during - * NAND boot because IFC signals > IFC_AD7 are not enabled. - * This workaround changes RCW source to make all signals enabled. - */ - porsr1 = in_be32(&gur->porsr1); - pinctl = ((porsr1 & ~(FSL_CORENET_CCSR_PORSR1_RCW_MASK)) | 0x24800000); - out_be32((unsigned int *)(CONFIG_SYS_DCSRBAR + 0x20000), pinctl); +#if defined(CONFIG_SPL_NAND_BOOT) && defined(CONFIG_A008044_WORKAROUND) + if (IS_SVR_REV(svr, 1, 0)) { + /* + * There is T1040 SoC issue where NOR, FPGA are inaccessible + * during NAND boot because IFC signals > IFC_AD7 are not + * enabled. This workaround changes RCW source to make all + * signals enabled. + */ + porsr1 = in_be32(&gur->porsr1); + pinctl = ((porsr1 & ~(FSL_CORENET_CCSR_PORSR1_RCW_MASK)) + | 0x24800000); + out_be32((unsigned int *)(CONFIG_SYS_DCSRBAR + 0x20000), + pinctl); + } #endif /* Memcpy existing GD at CONFIG_SPL_GD_ADDR */ diff --git a/board/freescale/t104xrdb/t104xrdb.c b/board/freescale/t104xrdb/t104xrdb.c index ddb669f..4734f9d 100644 --- a/board/freescale/t104xrdb/t104xrdb.c +++ b/board/freescale/t104xrdb/t104xrdb.c @@ -85,7 +85,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -110,6 +110,8 @@ void ft_board_setup(void *blob, bd_t *bd) #ifdef CONFIG_SYS_DPAA_FMAN fdt_fixup_fman_ethernet(blob); #endif + + return 0; } #ifdef CONFIG_DEEP_SLEEP diff --git a/board/freescale/t208xqds/README b/board/freescale/t208xqds/README new file mode 100755 index 0000000..83060c1 --- /dev/null +++ b/board/freescale/t208xqds/README @@ -0,0 +1,274 @@ +The T2080QDS is a high-performance computing evaluation, development and +test platform supporting the T2080 QorIQ Power Architecture processor. + +T2080 SoC Overview +------------------ +The T2080 QorIQ multicore processor combines four dual-threaded e6500 Power +Architecture processor cores with high-performance datapath acceleration +logic and network and peripheral bus interfaces required for networking, +telecom/datacom, wireless infrastructure, and mil/aerospace applications. + +T2080 includes the following functions and features: + - Four dual-threads 64-bit Power architecture e6500 cores, up to 1.8GHz + - 2MB L2 cache and 512KB CoreNet platform cache (CPC) + - Hierarchical interconnect fabric + - One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving + - Data Path Acceleration Architecture (DPAA) incorporating acceleration + - 16 SerDes lanes up to 10.3125 GHz + - 8 Ethernet interfaces, supporting combinations of the following: + - Up to four 10 Gbps Ethernet MACs + - Up to eight 1 Gbps Ethernet MACs + - Up to four 2.5 Gbps Ethernet MACs + - High-speed peripheral interfaces + - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV) + - Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz + - Additional peripheral interfaces + - Two serial ATA (SATA 2.0) controllers + - Two high-speed USB 2.0 controllers with integrated PHY + - Enhanced secure digital host controller (SD/SDHC/SDXC/eMMC) + - Enhanced serial peripheral interface (eSPI) + - Four I2C controllers + - Four 2-pin UARTs or two 4-pin UARTs + - Integrated Flash Controller supporting NAND and NOR flash + - Three eight-channel DMA engines + - Support for hardware virtualization and partitioning enforcement + - QorIQ Platform's Trust Architecture 2.0 + +Differences between T2080 and T2081 +----------------------------------- + Feature T2080 T2081 + 1G Ethernet numbers: 8 6 + 10G Ethernet numbers: 4 2 + SerDes lanes: 16 8 + Serial RapidIO,RMan: 2 no + SATA Controller: 2 no + Aurora: yes no + SoC Package: 896-pins 780-pins + + +T2080QDS feature overview +------------------------- +Processor: + - T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz +Memory: + - Single memory controller capable of supporting DDR3 and DDR3-LV devices + - Two DDR3 DIMMs up to 4GB, Dual rank @ 2133MT/s and ECC support +Ethernet interfaces: + - Two 1Gbps RGMII on-board ports + - Four 10Gbps XFI on-board cages + - 1Gbps/2.5Gbps SGMII Riser card + - 10Gbps XAUI Riser card +Accelerator: + - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC +SerDes: + - 16 lanes up to 10.3125GHz + - Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI +IFC: + - 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA +eSPI: + - Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040) +USB: + - Two USB2.0 ports with internal PHY (one Type-A + one micro Type-AB) +PCIE: + - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV) +SATA: + - Two SATA 2.0 ports on-board +SRIO: + - Two Serial RapidIO 2.0 ports up to 5 GHz +eSDHC: + - Supports SD/SDHC/SDXC/eMMC Card +I2C: + - Four I2C controllers. +UART: + - Dual 4-pins UART serial ports +System Logic: + - QIXIS-II FPGA system controll +Debug Features: + - Support Legacy, COP/JTAG, Aurora, Event and EVT +XFI: + - XFI is supported on T2080QDS through Lane A/B/C/D on Serdes 1 routed to + a on-board SFP+ cages, which to house optical module (fiber cable) or + direct attach cable(copper), the copper cable is used to emulate + 10GBASE-KR scenario. + So, for XFI usage, there are two scenarios, one will use fiber cable, + another will use copper cable. An hwconfig env "fsl_10gkr_copper" is + introduced to indicate a XFI port will use copper cable, and U-boot + will fixup the dtb accordingly. + It's used as: fsl_10gkr_copper:<10g_mac_name> + The <10g_mac_name> can be fm1_10g1, fm1_10g2, fm1_10g3, fm1_10g4, they + do not have to be coexist in hwconfig. If a MAC is listed in the env + "fsl_10gkr_copper", it will use copper cable, otherwise, fiber cable + will be used by default. + for ex. set "fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm1_10g3,fm1_10g4" in + hwconfig, then both four XFI ports will use copper cable. + set "fsl_10gkr_copper:fm1_10g1,fm1_10g2" in hwconfig, then first two + XFI ports will use copper cable, the other two XFI ports will use fiber + cable. +1000BASE-KX(1G-KX): + - T2080QDS can support 1G-KX by using SGMII protocol, but serdes lane + runs in 1G-KX mode. By default, the lane runs in SGMII mode, to set a lane + in 1G-KX mode, need to set corresponding bit in SerDes Protocol Configuration + Register 1 (PCCR1), and U-boot fixup the dtb for kernel to do proper + initialization. + Hwconfig "fsl_1gkx" is used to indicate a lane runs in 1G-KX mode, MAC + 1/2/5/6/9/10 are available for 1G-KX, MAC 3/4 run in RGMII mode. To set a + MAC to use 1G-KX mode, set its' corresponding env in "fsl_1gkx", 'fm1_1g1' + stands for MAC 1, 'fm1_1g2' stands for MAC 2, etc. + For ex. set "fsl_1gkx:fm1_1g1,fm1_1g2,fm1_1g5,fm1_1g6,fm1_1g9,fm1_1g10" in + hwconfig, MAC 1/2/5/6/9/10 will use 1G-KX mode. + +System Memory map +---------------- + +Start Address End Address Description Size +0xF_FFDF_0000 0xF_FFDF_0FFF IFC - CPLD 4KB +0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB +0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB +0xF_F803_0000 0xF_F803_FFFF PCI Express 4 I/O Space 64KB +0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB +0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB +0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB +0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB +0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB +0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB +0xF_0000_0000 0xF_003F_FFFF DCSR 4MB +0xC_4000_0000 0xC_4FFF_FFFF PCI Express 4 Mem Space 256MB +0xC_3000_0000 0xC_3FFF_FFFF PCI Express 3 Mem Space 256MB +0xC_2000_0000 0xC_2FFF_FFFF PCI Express 2 Mem Space 256MB +0xC_0000_0000 0xC_1FFF_FFFF PCI Express 1 Mem Space 512MB +0x0_0000_0000 0x0_ffff_ffff DDR 4GB + + +128M NOR Flash memory Map +------------------------- +Start Address End Address Definition Max size +0xEFF40000 0xEFFFFFFF u-boot (current bank) 768KB +0xEFF20000 0xEFF3FFFF u-boot env (current bank) 128KB +0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB +0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB +0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB +0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB +0xEC000000 0xEC01FFFF RCW (alt bank) 128KB +0xEBF40000 0xEBFFFFFF u-boot (alt bank) 768KB +0xEBF20000 0xEBF3FFFF u-boot env (alt bank) 128KB +0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB +0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB +0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 1MB +0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB +0xE8000000 0xE801FFFF RCW (current bank) 128KB + + + +Software configurations and board settings +------------------------------------------ +1. NOR boot: + a. build NOR boot image + $ make T2080QDS_config + $ make + b. program u-boot.bin image to NOR flash + => tftp 1000000 u-boot.bin + => pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize + set SW1[1:8] = '00010011', SW2[1] = '1', SW6[1:4] = '0000' for NOR boot + + Switching between default bank0 and alternate bank4 on NOR flash + To change boot source to vbank4: + by software: run command 'qixis_reset altbank' in u-boot. + by DIP-switch: set SW6[1:4] = '0100' + + To change boot source to vbank0: + by software: run command 'qixis_reset' in u-boot. + by DIP-Switch: set SW6[1:4] = '0000' + +2. NAND Boot: + a. build PBL image for NAND boot + $ make T2080QDS_NAND_config + $ make + b. program u-boot-with-spl-pbl.bin to NAND flash + => tftp 1000000 u-boot-with-spl-pbl.bin + => nand erase 0 $filesize + => nand write 1000000 0 $filesize + set SW1[1:8] = '10000010', SW2[1] = '0' and SW6[1:4] = '1001' for NAND boot + +3. SPI Boot: + a. build PBL image for SPI boot + $ make T2080QDS_SPIFLASH_config + $ make + b. program u-boot-with-spl-pbl.bin to SPI flash + => tftp 1000000 u-boot-with-spl-pbl.bin + => sf probe 0 + => sf erase 0 f0000 + => sf write 1000000 0 $filesize + set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot + +4. SD Boot: + a. build PBL image for SD boot + $ make T2080QDS_SDCARD_config + $ make + b. program u-boot-with-spl-pbl.bin to SD/MMC card + => tftp 1000000 u-boot-with-spl-pbl.bin + => mmc write 1000000 8 0x800 + => tftp 1000000 fsl_fman_ucode_T2080_xx.bin + => mmc write 1000000 0x820 80 + set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot + + +2-stage NAND/SPI/SD boot loader +------------------------------- +PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM. +SPL further initializes DDR using SPD and environment variables +and copy u-boot(768 KB) from NAND/SPI/SD device to DDR. +Finally SPL transers control to u-boot for futher booting. + +SPL has following features: + - Executes within 256K + - No relocation required + +Run time view of SPL framework +------------------------------------------------- +|Area | Address | +------------------------------------------------- +|SecureBoot header | 0xFFFC0000 (32KB) | +------------------------------------------------- +|GD, BD | 0xFFFC8000 (4KB) | +------------------------------------------------- +|ENV | 0xFFFC9000 (8KB) | +------------------------------------------------- +|HEAP | 0xFFFCB000 (50KB) | +------------------------------------------------- +|STACK | 0xFFFD8000 (22KB) | +------------------------------------------------- +|U-boot SPL | 0xFFFD8000 (160KB) | +------------------------------------------------- + +NAND Flash memory Map on T2080QDS +-------------------------------------------------------------- +Start End Definition Size +0x000000 0x0FFFFF u-boot img 1MB (2 blocks) +0x100000 0x17FFFF u-boot env 512KB (1 block) +0x180000 0x1FFFFF FMAN ucode 512KB (1 block) + + +Micro SD Card memory Map on T2080QDS +---------------------------------------------------- +Block #blocks Definition Size +0x008 2048 u-boot img 1MB +0x800 0016 u-boot env 8KB +0x820 0128 FMAN ucode 64KB + + +SPI Flash memory Map on T2080QDS +---------------------------------------------------- +Start End Definition Size +0x000000 0x0FFFFF u-boot img 1MB +0x100000 0x101FFF u-boot env 8KB +0x110000 0x11FFFF FMAN ucode 64KB + + +How to update the ucode of Freescale FMAN +----------------------------------------- +=> tftp 1000000 fsl_fman_ucode_t2080_xx.bin +=> pro off all;erase 0xeff00000 0xeff1ffff;cp 1000000 0xeff00000 $filesize + + +For more details, please refer to T2080QDS User Guide and access +website www.freescale.com and Freescale QorIQ SDK Infocenter document. diff --git a/board/freescale/t208xqds/ddr.h b/board/freescale/t208xqds/ddr.h index ed52fef6..9c26fdf 100644 --- a/board/freescale/t208xqds/ddr.h +++ b/board/freescale/t208xqds/ddr.h @@ -28,17 +28,16 @@ static const struct board_specific_parameters udimm0[] = { * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | */ - {2, 1200, 0, 5, 7, 0x0808090a, 0x0b0c0c0a}, - {2, 1500, 0, 5, 6, 0x07070809, 0x0a0b0b09}, - {2, 1600, 0, 5, 8, 0x090b0b0d, 0x0d0e0f0b}, - {2, 1700, 0, 4, 7, 0x080a0a0c, 0x0c0d0e0a}, - {2, 1900, 0, 5, 9, 0x0a0b0c0e, 0x0f10120c}, - {2, 2140, 0, 4, 8, 0x090a0b0d, 0x0e0f110b}, + {2, 1200, 0, 5, 7, 0x0708090a, 0x0b0c0d09}, + {2, 1400, 0, 5, 7, 0x08090a0c, 0x0d0e0f0a}, + {2, 1700, 0, 5, 8, 0x090a0b0c, 0x0e10110c}, + {2, 1900, 0, 5, 8, 0x090b0c0f, 0x1012130d}, + {2, 2140, 0, 5, 8, 0x090b0c0f, 0x1012130d}, {1, 1200, 0, 5, 7, 0x0808090a, 0x0b0c0c0a}, {1, 1500, 0, 5, 6, 0x07070809, 0x0a0b0b09}, {1, 1600, 0, 5, 8, 0x090b0b0d, 0x0d0e0f0b}, - {1, 1700, 0, 4, 7, 0x080a0a0c, 0x0c0d0e0a}, - {1, 1900, 0, 5, 9, 0x0a0b0c0e, 0x0f10120c}, + {1, 1700, 0, 4, 8, 0x080a0a0c, 0x0c0d0e0a}, + {1, 1900, 0, 5, 8, 0x090a0c0d, 0x0e0f110c}, {1, 2140, 0, 4, 8, 0x090a0b0d, 0x0e0f110b}, {} }; diff --git a/board/freescale/t208xqds/eth_t208xqds.c b/board/freescale/t208xqds/eth_t208xqds.c index 5879198..b82e9e7 100644 --- a/board/freescale/t208xqds/eth_t208xqds.c +++ b/board/freescale/t208xqds/eth_t208xqds.c @@ -23,6 +23,7 @@ #include <phy.h> #include <asm/fsl_dtsec.h> #include <asm/fsl_serdes.h> +#include <hwconfig.h> #include "../common/qixis.h" #include "../common/fman.h" #include "t208xqds_qixis.h" @@ -46,6 +47,15 @@ #define EMI2 8 #endif +#define PCCR1_SGMIIA_KX_MASK 0x00008000 +#define PCCR1_SGMIIB_KX_MASK 0x00004000 +#define PCCR1_SGMIIC_KX_MASK 0x00002000 +#define PCCR1_SGMIID_KX_MASK 0x00001000 +#define PCCR1_SGMIIE_KX_MASK 0x00000800 +#define PCCR1_SGMIIF_KX_MASK 0x00000400 +#define PCCR1_SGMIIG_KX_MASK 0x00000200 +#define PCCR1_SGMIIH_KX_MASK 0x00000100 + static int mdio_mux[NUM_FM_PORTS]; static const char * const mdio_names[] = { @@ -187,8 +197,18 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, { int phy; char alias[20]; + char lane_mode[2][20] = {"1000BASE-KX", "10GBASE-KR"}; + char buf[32] = "serdes-1,"; struct fixed_link f_link; + int media_type = 0; + int off; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); +#ifdef CONFIG_T2080QDS + serdes_corenet_t *srds_regs = + (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR; + u32 srds1_pccr1 = in_be32(&srds_regs->srdspccr1); +#endif u32 srds_s1 = in_be32(&gur->rcwsr[4]) & FSL_CORENET2_RCWSR4_SRDS1_PRTCL; @@ -199,9 +219,54 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, switch (port) { #if defined(CONFIG_T2080QDS) case FM1_DTSEC1: + if (hwconfig_sub("fsl_1gkx", "fm1_1g1")) { + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_1gkx1"); + fdt_status_okay_by_alias(fdt, "1gkx_pcs_mdio1"); + sprintf(buf, "%s%s%s", buf, "lane-c,", + (char *)lane_mode[0]); + out_be32(&srds_regs->srdspccr1, srds1_pccr1 | + PCCR1_SGMIIH_KX_MASK); + break; + } case FM1_DTSEC2: + if (hwconfig_sub("fsl_1gkx", "fm1_1g2")) { + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_1gkx2"); + fdt_status_okay_by_alias(fdt, "1gkx_pcs_mdio2"); + sprintf(buf, "%s%s%s", buf, "lane-d,", + (char *)lane_mode[0]); + out_be32(&srds_regs->srdspccr1, srds1_pccr1 | + PCCR1_SGMIIG_KX_MASK); + break; + } case FM1_DTSEC9: + if (hwconfig_sub("fsl_1gkx", "fm1_1g9")) { + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_1gkx9"); + fdt_status_okay_by_alias(fdt, "1gkx_pcs_mdio9"); + sprintf(buf, "%s%s%s", buf, "lane-a,", + (char *)lane_mode[0]); + out_be32(&srds_regs->srdspccr1, srds1_pccr1 | + PCCR1_SGMIIE_KX_MASK); + break; + } case FM1_DTSEC10: + if (hwconfig_sub("fsl_1gkx", "fm1_1g10")) { + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_1gkx10"); + fdt_status_okay_by_alias(fdt, + "1gkx_pcs_mdio10"); + sprintf(buf, "%s%s%s", buf, "lane-b,", + (char *)lane_mode[0]); + out_be32(&srds_regs->srdspccr1, srds1_pccr1 | + PCCR1_SGMIIF_KX_MASK); + break; + } if (mdio_mux[port] == EMI1_SLOT2) { sprintf(alias, "phy_sgmii_s2_%x", phy); fdt_set_phy_handle(fdt, compat, addr, alias); @@ -213,7 +278,29 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, } break; case FM1_DTSEC5: + if (hwconfig_sub("fsl_1gkx", "fm1_1g5")) { + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_1gkx5"); + fdt_status_okay_by_alias(fdt, "1gkx_pcs_mdio5"); + sprintf(buf, "%s%s%s", buf, "lane-g,", + (char *)lane_mode[0]); + out_be32(&srds_regs->srdspccr1, srds1_pccr1 | + PCCR1_SGMIIC_KX_MASK); + break; + } case FM1_DTSEC6: + if (hwconfig_sub("fsl_1gkx", "fm1_1g6")) { + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_1gkx6"); + fdt_status_okay_by_alias(fdt, "1gkx_pcs_mdio6"); + sprintf(buf, "%s%s%s", buf, "lane-h,", + (char *)lane_mode[0]); + out_be32(&srds_regs->srdspccr1, srds1_pccr1 | + PCCR1_SGMIID_KX_MASK); + break; + } if (mdio_mux[port] == EMI1_SLOT1) { sprintf(alias, "phy_sgmii_s1_%x", phy); fdt_set_phy_handle(fdt, compat, addr, alias); @@ -257,6 +344,12 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, default: break; } + if (media_type) { + /* set property for 1000BASE-KX in dtb */ + off = fdt_node_offset_by_compat_reg(fdt, + "fsl,fman-memac-mdio", addr + 0x1000); + fdt_setprop_string(fdt, off, "lane-instance", buf); + } } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII) { switch (srds_s1) { @@ -265,15 +358,77 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, case 0x6c: case 0x6d: case 0x71: - f_link.phy_id = port; - f_link.duplex = 1; - f_link.link_speed = 10000; - f_link.pause = 0; - f_link.asym_pause = 0; - /* no PHY for XFI */ - fdt_delprop(fdt, offset, "phy-handle"); - fdt_setprop(fdt, offset, "fixed-link", &f_link, - sizeof(f_link)); + /* + * if the 10G is XFI, check hwconfig to see what is the + * media type, there are two types, fiber or copper, + * fix the dtb accordingly. + */ + switch (port) { + case FM1_10GEC1: + if (hwconfig_sub("fsl_10gkr_copper", "fm1_10g1")) { + /* it's MAC9 */ + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_xfi9"); + fdt_status_okay_by_alias(fdt, "xfi_pcs_mdio9"); + sprintf(buf, "%s%s%s", buf, "lane-a,", + (char *)lane_mode[1]); + } + break; + case FM1_10GEC2: + if (hwconfig_sub("fsl_10gkr_copper", "fm1_10g2")) { + /* it's MAC10 */ + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_xfi10"); + fdt_status_okay_by_alias(fdt, "xfi_pcs_mdio10"); + sprintf(buf, "%s%s%s", buf, "lane-b,", + (char *)lane_mode[1]); + } + break; + case FM1_10GEC3: + if (hwconfig_sub("fsl_10gkr_copper", "fm1_10g3")) { + /* it's MAC1 */ + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_xfi1"); + fdt_status_okay_by_alias(fdt, "xfi_pcs_mdio1"); + sprintf(buf, "%s%s%s", buf, "lane-c,", + (char *)lane_mode[1]); + } + break; + case FM1_10GEC4: + if (hwconfig_sub("fsl_10gkr_copper", "fm1_10g4")) { + /* it's MAC2 */ + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_xfi2"); + fdt_status_okay_by_alias(fdt, "xfi_pcs_mdio2"); + sprintf(buf, "%s%s%s", buf, "lane-d,", + (char *)lane_mode[1]); + } + break; + default: + return; + } + + if (!media_type) { + /* fixed-link is used for XFI fiber cable */ + f_link.phy_id = port; + f_link.duplex = 1; + f_link.link_speed = 10000; + f_link.pause = 0; + f_link.asym_pause = 0; + fdt_delprop(fdt, offset, "phy-handle"); + fdt_setprop(fdt, offset, "fixed-link", &f_link, + sizeof(f_link)); + } else { + /* set property for copper cable */ + off = fdt_node_offset_by_compat_reg(fdt, + "fsl,fman-memac-mdio", addr + 0x1000); + fdt_setprop_string(fdt, off, + "lane-instance", buf); + } break; default: break; diff --git a/board/freescale/t208xqds/t2080_rcw.cfg b/board/freescale/t208xqds/t2080_rcw.cfg index 972dedc..52a1652 100644 --- a/board/freescale/t208xqds/t2080_rcw.cfg +++ b/board/freescale/t208xqds/t2080_rcw.cfg @@ -1,8 +1,16 @@ #PBL preamble and RCW header aa55aa55 010e0100 -#SerDes Protocol: 0x66_0x16 -#Core/DDR: 1533Mhz/2133MT/s -12100017 15000000 00000000 00000000 -66150002 00008400 e8104000 c1000000 + +#For T2080 v1.0 +#SerDes=0x66_0x16, Core=1533MHz, DDR=2133MT/s +#12100017 15000000 00000000 00000000 +#66150002 00008400 e8104000 c1000000 +#00000000 00000000 00000000 000307fc +#00000000 00000000 00000000 00000004 + +#For T2080 v1.1 +#SerDes=0x66_0x15, Core=1800MHz, DDR=1867MT/s +0c070012 0e000000 00000000 00000000 +66150002 00000000 e8104000 c1000000 00000000 00000000 00000000 000307fc 00000000 00000000 00000000 00000004 diff --git a/board/freescale/t208xqds/t208xqds.c b/board/freescale/t208xqds/t208xqds.c index fc6d256..7c89cd5 100644 --- a/board/freescale/t208xqds/t208xqds.c +++ b/board/freescale/t208xqds/t208xqds.c @@ -20,6 +20,7 @@ #include "../common/qixis.h" #include "../common/vsc3316_3308.h" +#include "../common/vid.h" #include "t208xqds.h" #include "t208xqds_qixis.h" @@ -86,6 +87,11 @@ int select_i2c_ch_pca9547(u8 ch) return 0; } +int i2c_multiplexer_select_vid_channel(u8 channel) +{ + return select_i2c_ch_pca9547(channel); +} + int brd_mux_lane_to_slot(void) { ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); @@ -358,6 +364,13 @@ int board_early_init_r(void) /* Disable remote I2C connection to qixis fpga */ QIXIS_WRITE(brdcfg[5], QIXIS_READ(brdcfg[5]) & ~BRDCFG5_IRE); + /* + * Adjust core voltage according to voltage ID + * This function changes I2C mux to channel 2. + */ + if (adjust_vdd(0)) + printf("Warning: Adjusting core voltage failed.\n"); + brd_mux_lane_to_slot(); select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT); @@ -437,7 +450,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -460,4 +473,6 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_fman_ethernet(blob); fdt_fixup_board_enet(blob); #endif + + return 0; } diff --git a/board/freescale/t208xrdb/t2080_rcw.cfg b/board/freescale/t208xrdb/t2080_rcw.cfg index 15e1bf4..59025ea 100644 --- a/board/freescale/t208xrdb/t2080_rcw.cfg +++ b/board/freescale/t208xrdb/t2080_rcw.cfg @@ -1,8 +1,16 @@ -#PBL preamble and RCW header for T2080RDB +#PBL preamble and RCW header aa55aa55 010e0100 -#SerDes Protocol: 0x66_0x16 -#Core/DDR: 1533Mhz/1600MT/s -120c0017 15000000 00000000 00000000 -66150002 00008400 ec104000 c1000000 -00000000 00000000 00000000 000307fc + +#For T2080 v1.0 +#SerDes=0x66_0x16, Core=1533MHz, DDR=1600MT/s +#120c0017 15000000 00000000 00000000 +#66150002 00008400 ec104000 c1000000 +#00000000 00000000 00000000 000307fc +#00000000 00000000 00000000 00000004 + +#For T2080 v1.1 +#SerDes=0x66_0x15, Core:1800MHz, DDR:1600MT/s +1206001b 15000000 00000000 00000000 +66150002 00000000 e8104000 c1000000 +00800000 00000000 00000000 000307fc 00000000 00000000 00000000 00000004 diff --git a/board/freescale/t208xrdb/t208xrdb.c b/board/freescale/t208xrdb/t208xrdb.c index be99fb8..341453b 100644 --- a/board/freescale/t208xrdb/t208xrdb.c +++ b/board/freescale/t208xrdb/t208xrdb.c @@ -103,7 +103,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -126,4 +126,6 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_fman_ethernet(blob); fdt_fixup_board_enet(blob); #endif + + return 0; } diff --git a/board/freescale/t4qds/t4240emu.c b/board/freescale/t4qds/t4240emu.c index 479e124..5441094 100644 --- a/board/freescale/t4qds/t4240emu.c +++ b/board/freescale/t4qds/t4240emu.c @@ -69,7 +69,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -83,4 +83,6 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_liodn(blob); fdt_fixup_dr_usb(blob, bd); + + return 0; } diff --git a/board/freescale/t4qds/t4240qds.c b/board/freescale/t4qds/t4240qds.c index 6205fea..4f2cccd 100644 --- a/board/freescale/t4qds/t4240qds.c +++ b/board/freescale/t4qds/t4240qds.c @@ -683,7 +683,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -706,6 +706,8 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_fman_ethernet(blob); fdt_fixup_board_enet(blob); #endif + + return 0; } /* diff --git a/board/freescale/t4rdb/t4240rdb.c b/board/freescale/t4rdb/t4240rdb.c index 2ff77b8..fac442b 100644 --- a/board/freescale/t4rdb/t4240rdb.c +++ b/board/freescale/t4rdb/t4240rdb.c @@ -88,7 +88,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -111,6 +111,8 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_fman_ethernet(blob); fdt_fixup_board_enet(blob); #endif + + return 0; } /* |