diff options
Diffstat (limited to 'board/esd/cpci750/sdram_init.c')
| -rw-r--r-- | board/esd/cpci750/sdram_init.c | 1702 |
1 files changed, 0 insertions, 1702 deletions
diff --git a/board/esd/cpci750/sdram_init.c b/board/esd/cpci750/sdram_init.c deleted file mode 100644 index 89f94aa..0000000 --- a/board/esd/cpci750/sdram_init.c +++ /dev/null @@ -1,1702 +0,0 @@ -/* - * (C) Copyright 2001 - * Josh Huber <huber@mclx.com>, Mission Critical Linux, Inc. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/************************************************************************* - * adaption for the Marvell DB64360 Board - * Ingo Assmus (ingo.assmus@keymile.com) - * - * adaption for the cpci750 Board - * Reinhard Arlt (reinhard.arlt@esd-electronics.com) - *************************************************************************/ - - -/* sdram_init.c - automatic memory sizing */ - -#include <common.h> -#include <74xx_7xx.h> -#include "../../Marvell/include/memory.h" -#include "../../Marvell/include/pci.h" -#include "../../Marvell/include/mv_gen_reg.h" -#include <net.h> - -#include "eth.h" -#include "mpsc.h" -#include "../../Marvell/common/i2c.h" -#include "64360.h" -#include "mv_regs.h" - -DECLARE_GLOBAL_DATA_PTR; - -int set_dfcdlInit(void); /* setup delay line of Mv64360 */ - -/* ------------------------------------------------------------------------- */ - -int -memory_map_bank(unsigned int bankNo, - unsigned int bankBase, - unsigned int bankLength) -{ -#ifdef MAP_PCI - PCI_HOST host; -#endif - - -#ifdef DEBUG - if (bankLength > 0) { - printf("mapping bank %d at %08x - %08x\n", - bankNo, bankBase, bankBase + bankLength - 1); - } else { - printf("unmapping bank %d\n", bankNo); - } -#endif - - memoryMapBank(bankNo, bankBase, bankLength); - -#ifdef MAP_PCI - for (host=PCI_HOST0;host<=PCI_HOST1;host++) { - const int features= - PREFETCH_ENABLE | - DELAYED_READ_ENABLE | - AGGRESSIVE_PREFETCH | - READ_LINE_AGGRESSIVE_PREFETCH | - READ_MULTI_AGGRESSIVE_PREFETCH | - MAX_BURST_4 | - PCI_NO_SWAP; - - pciMapMemoryBank(host, bankNo, bankBase, bankLength); - - pciSetRegionSnoopMode(host, bankNo, PCI_SNOOP_WB, bankBase, - bankLength); - - pciSetRegionFeatures(host, bankNo, features, bankBase, bankLength); - } -#endif - return 0; -} - -#define GB (1 << 30) - -/* much of this code is based on (or is) the code in the pip405 port */ -/* thanks go to the authors of said port - Josh */ - -/* structure to store the relevant information about an sdram bank */ -typedef struct sdram_info { - uchar drb_size; - uchar registered, ecc; - uchar tpar; - uchar tras_clocks; - uchar burst_len; - uchar banks, slot; -} sdram_info_t; - -/* Typedefs for 'gtAuxilGetDIMMinfo' function */ - -typedef enum _memoryType {SDRAM, DDR} MEMORY_TYPE; - -typedef enum _voltageInterface {TTL_5V_TOLERANT, LVTTL, HSTL_1_5V, - SSTL_3_3V, SSTL_2_5V, VOLTAGE_UNKNOWN, - } VOLTAGE_INTERFACE; - -typedef enum _max_CL_supported_DDR {DDR_CL_1=1, DDR_CL_1_5=2, DDR_CL_2=4, DDR_CL_2_5=8, DDR_CL_3=16, DDR_CL_3_5=32, DDR_CL_FAULT} MAX_CL_SUPPORTED_DDR; -typedef enum _max_CL_supported_SD {SD_CL_1=1, SD_CL_2, SD_CL_3, SD_CL_4, SD_CL_5, SD_CL_6, SD_CL_7, SD_FAULT} MAX_CL_SUPPORTED_SD; - - -/* SDRAM/DDR information struct */ -typedef struct _gtMemoryDimmInfo { - MEMORY_TYPE memoryType; - unsigned int numOfRowAddresses; - unsigned int numOfColAddresses; - unsigned int numOfModuleBanks; - unsigned int dataWidth; - VOLTAGE_INTERFACE voltageInterface; - unsigned int errorCheckType; /* ECC , PARITY.. */ - unsigned int sdramWidth; /* 4,8,16 or 32 */ ; - unsigned int errorCheckDataWidth; /* 0 - no, 1 - Yes */ - unsigned int minClkDelay; - unsigned int burstLengthSupported; - unsigned int numOfBanksOnEachDevice; - unsigned int suportedCasLatencies; - unsigned int RefreshInterval; - unsigned int maxCASlatencySupported_LoP; /* LoP left of point (measured in ns) */ - unsigned int maxCASlatencySupported_RoP; /* RoP right of point (measured in ns) */ - MAX_CL_SUPPORTED_DDR maxClSupported_DDR; - MAX_CL_SUPPORTED_SD maxClSupported_SD; - unsigned int moduleBankDensity; - /* module attributes (true for yes) */ - bool bufferedAddrAndControlInputs; - bool registeredAddrAndControlInputs; - bool onCardPLL; - bool bufferedDQMBinputs; - bool registeredDQMBinputs; - bool differentialClockInput; - bool redundantRowAddressing; - - /* module general attributes */ - bool suportedAutoPreCharge; - bool suportedPreChargeAll; - bool suportedEarlyRasPreCharge; - bool suportedWrite1ReadBurst; - bool suported5PercentLowVCC; - bool suported5PercentUpperVCC; - /* module timing parameters */ - unsigned int minRasToCasDelay; - unsigned int minRowActiveRowActiveDelay; - unsigned int minRasPulseWidth; - unsigned int minRowPrechargeTime; /* measured in ns */ - - int addrAndCommandHoldTime; /* LoP left of point (measured in ns) */ - int addrAndCommandSetupTime; /* (measured in ns/100) */ - int dataInputSetupTime; /* LoP left of point (measured in ns) */ - int dataInputHoldTime; /* LoP left of point (measured in ns) */ -/* tAC times for highest 2nd and 3rd highest CAS Latency values */ - unsigned int clockToDataOut_LoP; /* LoP left of point (measured in ns) */ - unsigned int clockToDataOut_RoP; /* RoP right of point (measured in ns) */ - unsigned int clockToDataOutMinus1_LoP; /* LoP left of point (measured in ns) */ - unsigned int clockToDataOutMinus1_RoP; /* RoP right of point (measured in ns) */ - unsigned int clockToDataOutMinus2_LoP; /* LoP left of point (measured in ns) */ - unsigned int clockToDataOutMinus2_RoP; /* RoP right of point (measured in ns) */ - - unsigned int minimumCycleTimeAtMaxCasLatancy_LoP; /* LoP left of point (measured in ns) */ - unsigned int minimumCycleTimeAtMaxCasLatancy_RoP; /* RoP right of point (measured in ns) */ - - unsigned int minimumCycleTimeAtMaxCasLatancyMinus1_LoP; /* LoP left of point (measured in ns) */ - unsigned int minimumCycleTimeAtMaxCasLatancyMinus1_RoP; /* RoP right of point (measured in ns) */ - - unsigned int minimumCycleTimeAtMaxCasLatancyMinus2_LoP; /* LoP left of point (measured in ns) */ - unsigned int minimumCycleTimeAtMaxCasLatancyMinus2_RoP; /* RoP right of point (measured in ns) */ - - /* Parameters calculated from - the extracted DIMM information */ - unsigned int size; - unsigned int deviceDensity; /* 16,64,128,256 or 512 Mbit */ - unsigned int numberOfDevices; - uchar drb_size; /* DRAM size in n*64Mbit */ - uchar slot; /* Slot Number this module is inserted in */ - uchar spd_raw_data[128]; /* Content of SPD-EEPROM copied 1:1 */ -#ifdef DEBUG - uchar manufactura[8]; /* Content of SPD-EEPROM Byte 64-71 */ - uchar modul_id[18]; /* Content of SPD-EEPROM Byte 73-90 */ - uchar vendor_data[27]; /* Content of SPD-EEPROM Byte 99-125 */ - unsigned long modul_serial_no; /* Content of SPD-EEPROM Byte 95-98 */ - unsigned int manufac_date; /* Content of SPD-EEPROM Byte 93-94 */ - unsigned int modul_revision; /* Content of SPD-EEPROM Byte 91-92 */ - uchar manufac_place; /* Content of SPD-EEPROM Byte 72 */ - -#endif -} AUX_MEM_DIMM_INFO; - - -/* - * translate ns.ns/10 coding of SPD timing values - * into 10 ps unit values - */ -static inline unsigned short -NS10to10PS(unsigned char spd_byte) -{ - unsigned short ns, ns10; - - /* isolate upper nibble */ - ns = (spd_byte >> 4) & 0x0F; - /* isolate lower nibble */ - ns10 = (spd_byte & 0x0F); - - return(ns*100 + ns10*10); -} - -/* - * translate ns coding of SPD timing values - * into 10 ps unit values - */ -static inline unsigned short -NSto10PS(unsigned char spd_byte) -{ - return(spd_byte*100); -} - -/* This code reads the SPD chip on the sdram and populates - * the array which is passed in with the relevant information */ -/* static int check_dimm(uchar slot, AUX_MEM_DIMM_INFO *info) */ -static int check_dimm (uchar slot, AUX_MEM_DIMM_INFO * dimmInfo) -{ - uchar addr = slot == 0 ? DIMM0_I2C_ADDR : DIMM1_I2C_ADDR; - int ret; - unsigned int i, j, density = 1, devicesForErrCheck = 0; - -#ifdef DEBUG - unsigned int k; -#endif - unsigned int rightOfPoint = 0, leftOfPoint = 0, mult, div, time_tmp; - int sign = 1, shift, maskLeftOfPoint, maskRightOfPoint; - uchar supp_cal, cal_val; - ulong memclk, tmemclk; - ulong tmp; - uchar trp_clocks = 0, tras_clocks; - uchar data[128]; - - memclk = gd->bus_clk; - tmemclk = 1000000000 / (memclk / 100); /* in 10 ps units */ - - memset (data, 0, sizeof (data)); - - - ret = 0; - - debug("before i2c read\n"); - - ret = i2c_read (addr, 0, 2, data, 128); - - debug("after i2c read\n"); - - if ((data[64] != 'e') || (data[65] != 's') || (data[66] != 'd') - || (data[67] != '-') || (data[68] != 'g') || (data[69] != 'm') - || (data[70] != 'b') || (data[71] != 'h')) { - ret = -1; - } - - if ((ret != 0) && (slot == 0)) { - memset (data, 0, sizeof (data)); - data[0] = 0x80; - data[1] = 0x08; - data[2] = 0x07; - data[3] = 0x0c; - data[4] = 0x09; - data[5] = 0x01; - data[6] = 0x48; - data[7] = 0x00; - data[8] = 0x04; - data[9] = 0x75; - data[10] = 0x80; - data[11] = 0x02; - data[12] = 0x80; - data[13] = 0x10; - data[14] = 0x08; - data[15] = 0x01; - data[16] = 0x0e; - data[17] = 0x04; - data[18] = 0x0c; - data[19] = 0x01; - data[20] = 0x02; - data[21] = 0x20; - data[22] = 0x00; - data[23] = 0xa0; - data[24] = 0x80; - data[25] = 0x00; - data[26] = 0x00; - data[27] = 0x50; - data[28] = 0x3c; - data[29] = 0x50; - data[30] = 0x32; - data[31] = 0x10; - data[32] = 0xb0; - data[33] = 0xb0; - data[34] = 0x60; - data[35] = 0x60; - data[64] = 'e'; - data[65] = 's'; - data[66] = 'd'; - data[67] = '-'; - data[68] = 'g'; - data[69] = 'm'; - data[70] = 'b'; - data[71] = 'h'; - ret = 0; - } - - /* zero all the values */ - memset (dimmInfo, 0, sizeof (*dimmInfo)); - - /* copy the SPD content 1:1 into the dimmInfo structure */ - for (i = 0; i <= 127; i++) { - dimmInfo->spd_raw_data[i] = data[i]; - } - - if (ret) { - debug("No DIMM in slot %d [err = %x]\n", slot, ret); - return 0; - } else - dimmInfo->slot = slot; /* start to fill up dimminfo for this "slot" */ - -#ifdef CONFIG_SYS_DISPLAY_DIMM_SPD_CONTENT - - for (i = 0; i <= 127; i++) { - printf ("SPD-EEPROM Byte %3d = %3x (%3d)\n", i, data[i], - data[i]); - } - -#endif -#ifdef DEBUG - /* find Manufacturer of Dimm Module */ - for (i = 0; i < sizeof (dimmInfo->manufactura); i++) { - dimmInfo->manufactura[i] = data[64 + i]; - } - printf ("\nThis RAM-Module is produced by: %s\n", - dimmInfo->manufactura); - - /* find Manul-ID of Dimm Module */ - for (i = 0; i < sizeof (dimmInfo->modul_id); i++) { - dimmInfo->modul_id[i] = data[73 + i]; - } - printf ("The Module-ID of this RAM-Module is: %s\n", - dimmInfo->modul_id); - - /* find Vendor-Data of Dimm Module */ - for (i = 0; i < sizeof (dimmInfo->vendor_data); i++) { - dimmInfo->vendor_data[i] = data[99 + i]; - } - printf ("Vendor Data of this RAM-Module is: %s\n", - dimmInfo->vendor_data); - - /* find modul_serial_no of Dimm Module */ - dimmInfo->modul_serial_no = (*((unsigned long *) (&data[95]))); - printf ("Serial No. of this RAM-Module is: %ld (%lx)\n", - dimmInfo->modul_serial_no, dimmInfo->modul_serial_no); - - /* find Manufac-Data of Dimm Module */ - dimmInfo->manufac_date = (*((unsigned int *) (&data[93]))); - printf ("Manufactoring Date of this RAM-Module is: %d.%d\n", data[93], data[94]); /*dimmInfo->manufac_date */ - - /* find modul_revision of Dimm Module */ - dimmInfo->modul_revision = (*((unsigned int *) (&data[91]))); - printf ("Module Revision of this RAM-Module is: %d.%d\n", data[91], data[92]); /* dimmInfo->modul_revision */ - - /* find manufac_place of Dimm Module */ - dimmInfo->manufac_place = (*((unsigned char *) (&data[72]))); - printf ("manufac_place of this RAM-Module is: %d\n", - dimmInfo->manufac_place); - -#endif -/*------------------------------------------------------------------------------------------------------------------------------*/ -/* calculate SPD checksum */ -/*------------------------------------------------------------------------------------------------------------------------------*/ -#if 0 /* test-only */ - spd_checksum = 0; - - for (i = 0; i <= 62; i++) { - spd_checksum += data[i]; - } - - if ((spd_checksum & 0xff) != data[63]) { - printf ("### Error in SPD Checksum !!! Is_value: %2x should value %2x\n", (unsigned int) (spd_checksum & 0xff), data[63]); - hang (); - } - - else - printf ("SPD Checksum ok!\n"); -#endif /* test-only */ - -/*------------------------------------------------------------------------------------------------------------------------------*/ - for (i = 2; i <= 35; i++) { - switch (i) { - case 2: /* Memory type (DDR / SDRAM) */ - dimmInfo->memoryType = (data[i] == 0x7) ? DDR : SDRAM; -#ifdef DEBUG - if (dimmInfo->memoryType == 0) - debug("Dram_type in slot %d is: SDRAM\n", - dimmInfo->slot); - if (dimmInfo->memoryType == 1) - debug("Dram_type in slot %d is: DDRAM\n", - dimmInfo->slot); -#endif - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 3: /* Number Of Row Addresses */ - dimmInfo->numOfRowAddresses = data[i]; - debug("Module Number of row addresses: %d\n", - dimmInfo->numOfRowAddresses); - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 4: /* Number Of Column Addresses */ - dimmInfo->numOfColAddresses = data[i]; - debug("Module Number of col addresses: %d\n", - dimmInfo->numOfColAddresses); - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 5: /* Number Of Module Banks */ - dimmInfo->numOfModuleBanks = data[i]; - debug("Number of Banks on Mod. : %d\n", - dimmInfo->numOfModuleBanks); - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 6: /* Data Width */ - dimmInfo->dataWidth = data[i]; - debug("Module Data Width: %d\n", - dimmInfo->dataWidth); - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 8: /* Voltage Interface */ - switch (data[i]) { - case 0x0: - dimmInfo->voltageInterface = TTL_5V_TOLERANT; - debug("Module is TTL_5V_TOLERANT\n"); - break; - case 0x1: - dimmInfo->voltageInterface = LVTTL; - debug("Module is LVTTL\n"); - break; - case 0x2: - dimmInfo->voltageInterface = HSTL_1_5V; - debug("Module is TTL_5V_TOLERANT\n"); - break; - case 0x3: - dimmInfo->voltageInterface = SSTL_3_3V; - debug("Module is HSTL_1_5V\n"); - break; - case 0x4: - dimmInfo->voltageInterface = SSTL_2_5V; - debug("Module is SSTL_2_5V\n"); - break; - default: - dimmInfo->voltageInterface = VOLTAGE_UNKNOWN; - debug("Module is VOLTAGE_UNKNOWN\n"); - break; - } - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 9: /* Minimum Cycle Time At Max CasLatancy */ - shift = (dimmInfo->memoryType == DDR) ? 4 : 2; - mult = (dimmInfo->memoryType == DDR) ? 10 : 25; - maskLeftOfPoint = - (dimmInfo->memoryType == DDR) ? 0xf0 : 0xfc; - maskRightOfPoint = - (dimmInfo->memoryType == DDR) ? 0xf : 0x03; - leftOfPoint = (data[i] & maskLeftOfPoint) >> shift; - rightOfPoint = (data[i] & maskRightOfPoint) * mult; - dimmInfo->minimumCycleTimeAtMaxCasLatancy_LoP = - leftOfPoint; - dimmInfo->minimumCycleTimeAtMaxCasLatancy_RoP = - rightOfPoint; - debug("Minimum Cycle Time At Max CasLatancy: %d.%d [ns]\n", - leftOfPoint, rightOfPoint); - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 10: /* Clock To Data Out */ - div = (dimmInfo->memoryType == DDR) ? 100 : 10; - time_tmp = - (((data[i] & 0xf0) >> 4) * 10) + - ((data[i] & 0x0f)); - leftOfPoint = time_tmp / div; - rightOfPoint = time_tmp % div; - dimmInfo->clockToDataOut_LoP = leftOfPoint; - dimmInfo->clockToDataOut_RoP = rightOfPoint; - debug("Clock To Data Out: %d.%2d [ns]\n", - leftOfPoint, rightOfPoint); - /*dimmInfo->clockToDataOut */ - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - -#ifdef CONFIG_MV64360_ECC - case 11: /* Error Check Type */ - dimmInfo->errorCheckType = data[i]; - debug("Error Check Type (0=NONE): %d\n", - dimmInfo->errorCheckType); - break; -#endif /* of ifdef CONFIG_MV64360_ECC */ -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 12: /* Refresh Interval */ - dimmInfo->RefreshInterval = data[i]; - debug("RefreshInterval (80= Self refresh Normal, 15.625us) : %x\n", - dimmInfo->RefreshInterval); - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 13: /* Sdram Width */ - dimmInfo->sdramWidth = data[i]; - debug("Sdram Width: %d\n", - dimmInfo->sdramWidth); - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 14: /* Error Check Data Width */ - dimmInfo->errorCheckDataWidth = data[i]; - debug("Error Check Data Width: %d\n", - dimmInfo->errorCheckDataWidth); - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 15: /* Minimum Clock Delay */ - dimmInfo->minClkDelay = data[i]; - debug("Minimum Clock Delay: %d\n", - dimmInfo->minClkDelay); - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 16: /* Burst Length Supported */ - /******-******-******-******* - * bit3 | bit2 | bit1 | bit0 * - *******-******-******-******* - burst length = * 8 | 4 | 2 | 1 * - ***************************** - - If for example bit0 and bit2 are set, the burst - length supported are 1 and 4. */ - - dimmInfo->burstLengthSupported = data[i]; -#ifdef DEBUG - debug("Burst Length Supported: "); - if (dimmInfo->burstLengthSupported & 0x01) - debug("1, "); - if (dimmInfo->burstLengthSupported & 0x02) - debug("2, "); - if (dimmInfo->burstLengthSupported & 0x04) - debug("4, "); - if (dimmInfo->burstLengthSupported & 0x08) - debug("8, "); - debug(" Bit \n"); -#endif - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 17: /* Number Of Banks On Each Device */ - dimmInfo->numOfBanksOnEachDevice = data[i]; - debug("Number Of Banks On Each Chip: %d\n", - dimmInfo->numOfBanksOnEachDevice); - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 18: /* Suported Cas Latencies */ - - /* DDR: - *******-******-******-******-******-******-******-******* - * bit7 | bit6 | bit5 | bit4 | bit3 | bit2 | bit1 | bit0 * - *******-******-******-******-******-******-******-******* - CAS = * TBD | TBD | 3.5 | 3 | 2.5 | 2 | 1.5 | 1 * - ********************************************************* - SDRAM: - *******-******-******-******-******-******-******-******* - * bit7 | bit6 | bit5 | bit4 | bit3 | bit2 | bit1 | bit0 * - *******-******-******-******-******-******-******-******* - CAS = * TBD | 7 | 6 | 5 | 4 | 3 | 2 | 1 * - ********************************************************/ - dimmInfo->suportedCasLatencies = data[i]; -#ifdef DEBUG - debug("Suported Cas Latencies: (CL) "); - if (dimmInfo->memoryType == 0) { /* SDRAM */ - for (k = 0; k <= 7; k++) { - if (dimmInfo-> - suportedCasLatencies & (1 << k)) - debug("%d, ", - k + 1); - } - - } else { /* DDR-RAM */ - - if (dimmInfo->suportedCasLatencies & 1) - debug("1, "); - if (dimmInfo->suportedCasLatencies & 2) - debug("1.5, "); - if (dimmInfo->suportedCasLatencies & 4) - debug("2, "); - if (dimmInfo->suportedCasLatencies & 8) - debug("2.5, "); - if (dimmInfo->suportedCasLatencies & 16) - debug("3, "); - if (dimmInfo->suportedCasLatencies & 32) - debug("3.5, "); - - } - debug("\n"); -#endif - /* Calculating MAX CAS latency */ - for (j = 7; j > 0; j--) { - if (((dimmInfo-> - suportedCasLatencies >> j) & 0x1) == - 1) { - switch (dimmInfo->memoryType) { - case DDR: - /* CAS latency 1, 1.5, 2, 2.5, 3, 3.5 */ - switch (j) { - case 7: - debug("Max. Cas Latencies (DDR): ERROR !!!\n"); - dimmInfo-> - maxClSupported_DDR - = - DDR_CL_FAULT; - hang (); - break; - case 6: - debug("Max. Cas Latencies (DDR): ERROR !!!\n"); - dimmInfo-> - maxClSupported_DDR - = - DDR_CL_FAULT; - hang (); - break; - case 5: - debug("Max. Cas Latencies (DDR): 3.5 clk's\n"); - dimmInfo-> - maxClSupported_DDR - = DDR_CL_3_5; - break; - case 4: - debug("Max. Cas Latencies (DDR): 3 clk's \n"); - dimmInfo-> - maxClSupported_DDR - = DDR_CL_3; - break; - case 3: - debug("Max. Cas Latencies (DDR): 2.5 clk's \n"); - dimmInfo-> - maxClSupported_DDR - = DDR_CL_2_5; - break; - case 2: - debug("Max. Cas Latencies (DDR): 2 clk's \n"); - dimmInfo-> - maxClSupported_DDR - = DDR_CL_2; - break; - case 1: - debug("Max. Cas Latencies (DDR): 1.5 clk's \n"); - dimmInfo-> - maxClSupported_DDR - = DDR_CL_1_5; - break; - } - dimmInfo-> - maxCASlatencySupported_LoP - = - 1 + - (int) (5 * j / 10); - if (((5 * j) % 10) != 0) - dimmInfo-> - maxCASlatencySupported_RoP - = 5; - else - dimmInfo-> - maxCASlatencySupported_RoP - = 0; - debug("Max. Cas Latencies (DDR LoP.RoP Notation): %d.%d \n", - dimmInfo-> - maxCASlatencySupported_LoP, - dimmInfo-> - maxCASlatencySupported_RoP); - break; - case SDRAM: - /* CAS latency 1, 2, 3, 4, 5, 6, 7 */ - dimmInfo->maxClSupported_SD = j; /* Cas Latency DDR-RAM Coded */ - debug("Max. Cas Latencies (SD): %d\n", - dimmInfo-> - maxClSupported_SD); - dimmInfo-> - maxCASlatencySupported_LoP - = j; - dimmInfo-> - maxCASlatencySupported_RoP - = 0; - debug("Max. Cas Latencies (DDR LoP.RoP Notation): %d.%d \n", - dimmInfo-> - maxCASlatencySupported_LoP, - dimmInfo-> - maxCASlatencySupported_RoP); - break; - } - break; - } - } - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 21: /* Buffered Address And Control Inputs */ - debug("\nModul Attributes (SPD Byte 21): \n"); - dimmInfo->bufferedAddrAndControlInputs = - data[i] & BIT0; - dimmInfo->registeredAddrAndControlInputs = - (data[i] & BIT1) >> 1; - dimmInfo->onCardPLL = (data[i] & BIT2) >> 2; - dimmInfo->bufferedDQMBinputs = (data[i] & BIT3) >> 3; - dimmInfo->registeredDQMBinputs = - (data[i] & BIT4) >> 4; - dimmInfo->differentialClockInput = - (data[i] & BIT5) >> 5; - dimmInfo->redundantRowAddressing = - (data[i] & BIT6) >> 6; - - if (dimmInfo->bufferedAddrAndControlInputs == 1) - debug(" - Buffered Address/Control Input: Yes \n"); - else - debug(" - Buffered Address/Control Input: No \n"); - - if (dimmInfo->registeredAddrAndControlInputs == 1) - debug(" - Registered Address/Control Input: Yes \n"); - else - debug(" - Registered Address/Control Input: No \n"); - - if (dimmInfo->onCardPLL == 1) - debug(" - On-Card PLL (clock): Yes \n"); - else - debug(" - On-Card PLL (clock): No \n"); - - if (dimmInfo->bufferedDQMBinputs == 1) - debug(" - Bufferd DQMB Inputs: Yes \n"); - else - debug(" - Bufferd DQMB Inputs: No \n"); - - if (dimmInfo->registeredDQMBinputs == 1) - debug(" - Registered DQMB Inputs: Yes \n"); - else - debug(" - Registered DQMB Inputs: No \n"); - - if (dimmInfo->differentialClockInput == 1) - debug(" - Differential Clock Input: Yes \n"); - else - debug(" - Differential Clock Input: No \n"); - - if (dimmInfo->redundantRowAddressing == 1) - debug(" - redundant Row Addressing: Yes \n"); - else - debug(" - redundant Row Addressing: No \n"); - - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 22: /* Suported AutoPreCharge */ - debug("\nModul Attributes (SPD Byte 22): \n"); - dimmInfo->suportedEarlyRasPreCharge = data[i] & BIT0; - dimmInfo->suportedAutoPreCharge = - (data[i] & BIT1) >> 1; - dimmInfo->suportedPreChargeAll = - (data[i] & BIT2) >> 2; - dimmInfo->suportedWrite1ReadBurst = - (data[i] & BIT3) >> 3; - dimmInfo->suported5PercentLowVCC = - (data[i] & BIT4) >> 4; - dimmInfo->suported5PercentUpperVCC = - (data[i] & BIT5) >> 5; - - if (dimmInfo->suportedEarlyRasPreCharge == 1) - debug(" - Early Ras Precharge: Yes \n"); - else - debug(" - Early Ras Precharge: No \n"); - - if (dimmInfo->suportedAutoPreCharge == 1) - debug(" - AutoPreCharge: Yes \n"); - else - debug(" - AutoPreCharge: No \n"); - - if (dimmInfo->suportedPreChargeAll == 1) - debug(" - Precharge All: Yes \n"); - else - debug(" - Precharge All: No \n"); - - if (dimmInfo->suportedWrite1ReadBurst == 1) - debug(" - Write 1/ReadBurst: Yes \n"); - else - debug(" - Write 1/ReadBurst: No \n"); - - if (dimmInfo->suported5PercentLowVCC == 1) - debug(" - lower VCC tolerance: 5 Percent \n"); - else - debug(" - lower VCC tolerance: 10 Percent \n"); - - if (dimmInfo->suported5PercentUpperVCC == 1) - debug(" - upper VCC tolerance: 5 Percent \n"); - else - debug(" - upper VCC tolerance: 10 Percent \n"); - - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 23: /* Minimum Cycle Time At Maximum Cas Latancy Minus 1 (2nd highest CL) */ - shift = (dimmInfo->memoryType == DDR) ? 4 : 2; - mult = (dimmInfo->memoryType == DDR) ? 10 : 25; - maskLeftOfPoint = - (dimmInfo->memoryType == DDR) ? 0xf0 : 0xfc; - maskRightOfPoint = - (dimmInfo->memoryType == DDR) ? 0xf : 0x03; - leftOfPoint = (data[i] & maskLeftOfPoint) >> shift; - rightOfPoint = (data[i] & maskRightOfPoint) * mult; - dimmInfo->minimumCycleTimeAtMaxCasLatancyMinus1_LoP = - leftOfPoint; - dimmInfo->minimumCycleTimeAtMaxCasLatancyMinus1_RoP = - rightOfPoint; - debug("Minimum Cycle Time At 2nd highest CasLatancy (0 = Not supported): %d.%d [ns]\n", - leftOfPoint, rightOfPoint); - /*dimmInfo->minimumCycleTimeAtMaxCasLatancy */ - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 24: /* Clock To Data Out 2nd highest Cas Latency Value */ - div = (dimmInfo->memoryType == DDR) ? 100 : 10; - time_tmp = - (((data[i] & 0xf0) >> 4) * 10) + - ((data[i] & 0x0f)); - leftOfPoint = time_tmp / div; - rightOfPoint = time_tmp % div; - dimmInfo->clockToDataOutMinus1_LoP = leftOfPoint; - dimmInfo->clockToDataOutMinus1_RoP = rightOfPoint; - debug("Clock To Data Out (2nd CL value): %d.%2d [ns]\n", - leftOfPoint, rightOfPoint); - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 25: /* Minimum Cycle Time At Maximum Cas Latancy Minus 2 (3rd highest CL) */ - shift = (dimmInfo->memoryType == DDR) ? 4 : 2; - mult = (dimmInfo->memoryType == DDR) ? 10 : 25; - maskLeftOfPoint = - (dimmInfo->memoryType == DDR) ? 0xf0 : 0xfc; - maskRightOfPoint = - (dimmInfo->memoryType == DDR) ? 0xf : 0x03; - leftOfPoint = (data[i] & maskLeftOfPoint) >> shift; - rightOfPoint = (data[i] & maskRightOfPoint) * mult; - dimmInfo->minimumCycleTimeAtMaxCasLatancyMinus2_LoP = - leftOfPoint; - dimmInfo->minimumCycleTimeAtMaxCasLatancyMinus2_RoP = - rightOfPoint; - debug("Minimum Cycle Time At 3rd highest CasLatancy (0 = Not supported): %d.%d [ns]\n", - leftOfPoint, rightOfPoint); - /*dimmInfo->minimumCycleTimeAtMaxCasLatancy */ - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 26: /* Clock To Data Out 3rd highest Cas Latency Value */ - div = (dimmInfo->memoryType == DDR) ? 100 : 10; - time_tmp = - (((data[i] & 0xf0) >> 4) * 10) + - ((data[i] & 0x0f)); - leftOfPoint = time_tmp / div; - rightOfPoint = time_tmp % div; - dimmInfo->clockToDataOutMinus2_LoP = leftOfPoint; - dimmInfo->clockToDataOutMinus2_RoP = rightOfPoint; - debug("Clock To Data Out (3rd CL value): %d.%2d [ns]\n", - leftOfPoint, rightOfPoint); - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 27: /* Minimum Row Precharge Time */ - shift = (dimmInfo->memoryType == DDR) ? 2 : 0; - maskLeftOfPoint = - (dimmInfo->memoryType == DDR) ? 0xfc : 0xff; - maskRightOfPoint = - (dimmInfo->memoryType == DDR) ? 0x03 : 0x00; - leftOfPoint = ((data[i] & maskLeftOfPoint) >> shift); - rightOfPoint = (data[i] & maskRightOfPoint) * 25; - - dimmInfo->minRowPrechargeTime = ((leftOfPoint * 100) + rightOfPoint); /* measured in n times 10ps Intervals */ - trp_clocks = - (dimmInfo->minRowPrechargeTime + - (tmemclk - 1)) / tmemclk; - debug("*** 1 clock cycle = %ld 10ps intervalls = %ld.%ld ns****\n", - tmemclk, tmemclk / 100, tmemclk % 100); - debug("Minimum Row Precharge Time [ns]: %d.%2d = in Clk cycles %d\n", - leftOfPoint, rightOfPoint, trp_clocks); - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 28: /* Minimum Row Active to Row Active Time */ - shift = (dimmInfo->memoryType == DDR) ? 2 : 0; - maskLeftOfPoint = - (dimmInfo->memoryType == DDR) ? 0xfc : 0xff; - maskRightOfPoint = - (dimmInfo->memoryType == DDR) ? 0x03 : 0x00; - leftOfPoint = ((data[i] & maskLeftOfPoint) >> shift); - rightOfPoint = (data[i] & maskRightOfPoint) * 25; - - dimmInfo->minRowActiveRowActiveDelay = ((leftOfPoint * 100) + rightOfPoint); /* measured in 100ns Intervals */ - debug("Minimum Row Active -To- Row Active Delay [ns]: %d.%2d = in Clk cycles %d\n", - leftOfPoint, rightOfPoint, trp_clocks); - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 29: /* Minimum Ras-To-Cas Delay */ - shift = (dimmInfo->memoryType == DDR) ? 2 : 0; - maskLeftOfPoint = - (dimmInfo->memoryType == DDR) ? 0xfc : 0xff; - maskRightOfPoint = - (dimmInfo->memoryType == DDR) ? 0x03 : 0x00; - leftOfPoint = ((data[i] & maskLeftOfPoint) >> shift); - rightOfPoint = (data[i] & maskRightOfPoint) * 25; - - dimmInfo->minRowActiveRowActiveDelay = ((leftOfPoint * 100) + rightOfPoint); /* measured in 100ns Intervals */ - debug("Minimum Ras-To-Cas Delay [ns]: %d.%2d = in Clk cycles %d\n", - leftOfPoint, rightOfPoint, trp_clocks); - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 30: /* Minimum Ras Pulse Width */ - dimmInfo->minRasPulseWidth = data[i]; - tras_clocks = - (NSto10PS (data[i]) + - (tmemclk - 1)) / tmemclk; - debug("Minimum Ras Pulse Width [ns]: %d = in Clk cycles %d\n", - dimmInfo->minRasPulseWidth, tras_clocks); - - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 31: /* Module Bank Density */ - dimmInfo->moduleBankDensity = data[i]; - debug("Module Bank Density: %d\n", - dimmInfo->moduleBankDensity); -#ifdef DEBUG - debug("*** Offered Densities (more than 1 = Multisize-Module): "); - { - if (dimmInfo->moduleBankDensity & 1) - debug("4MB, "); - if (dimmInfo->moduleBankDensity & 2) - debug("8MB, "); - if (dimmInfo->moduleBankDensity & 4) - debug("16MB, "); - if (dimmInfo->moduleBankDensity & 8) - debug("32MB, "); - if (dimmInfo->moduleBankDensity & 16) - debug("64MB, "); - if (dimmInfo->moduleBankDensity & 32) - debug("128MB, "); - if ((dimmInfo->moduleBankDensity & 64) - || (dimmInfo->moduleBankDensity & 128)) { - debug("ERROR, "); - hang (); - } - } - debug("\n"); -#endif - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 32: /* Address And Command Setup Time (measured in ns/1000) */ - sign = 1; - switch (dimmInfo->memoryType) { - case DDR: - time_tmp = - (((data[i] & 0xf0) >> 4) * 10) + - ((data[i] & 0x0f)); - leftOfPoint = time_tmp / 100; - rightOfPoint = time_tmp % 100; - break; - case SDRAM: - leftOfPoint = (data[i] & 0xf0) >> 4; - if (leftOfPoint > 7) { - leftOfPoint = data[i] & 0x70 >> 4; - sign = -1; - } - rightOfPoint = (data[i] & 0x0f); - break; - } - dimmInfo->addrAndCommandSetupTime = - (leftOfPoint * 100 + rightOfPoint) * sign; - debug("Address And Command Setup Time [ns]: %d.%d\n", - sign * leftOfPoint, rightOfPoint); - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 33: /* Address And Command Hold Time */ - sign = 1; - switch (dimmInfo->memoryType) { - case DDR: - time_tmp = - (((data[i] & 0xf0) >> 4) * 10) + - ((data[i] & 0x0f)); - leftOfPoint = time_tmp / 100; - rightOfPoint = time_tmp % 100; - break; - case SDRAM: - leftOfPoint = (data[i] & 0xf0) >> 4; - if (leftOfPoint > 7) { - leftOfPoint = data[i] & 0x70 >> 4; - sign = -1; - } - rightOfPoint = (data[i] & 0x0f); - break; - } - dimmInfo->addrAndCommandHoldTime = - (leftOfPoint * 100 + rightOfPoint) * sign; - debug("Address And Command Hold Time [ns]: %d.%d\n", - sign * leftOfPoint, rightOfPoint); - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 34: /* Data Input Setup Time */ - sign = 1; - switch (dimmInfo->memoryType) { - case DDR: - time_tmp = - (((data[i] & 0xf0) >> 4) * 10) + - ((data[i] & 0x0f)); - leftOfPoint = time_tmp / 100; - rightOfPoint = time_tmp % 100; - break; - case SDRAM: - leftOfPoint = (data[i] & 0xf0) >> 4; - if (leftOfPoint > 7) { - leftOfPoint = data[i] & 0x70 >> 4; - sign = -1; - } - rightOfPoint = (data[i] & 0x0f); - break; - } - dimmInfo->dataInputSetupTime = - (leftOfPoint * 100 + rightOfPoint) * sign; - debug("Data Input Setup Time [ns]: %d.%d\n", - sign * leftOfPoint, rightOfPoint); - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - - case 35: /* Data Input Hold Time */ - sign = 1; - switch (dimmInfo->memoryType) { - case DDR: - time_tmp = - (((data[i] & 0xf0) >> 4) * 10) + - ((data[i] & 0x0f)); - leftOfPoint = time_tmp / 100; - rightOfPoint = time_tmp % 100; - break; - case SDRAM: - leftOfPoint = (data[i] & 0xf0) >> 4; - if (leftOfPoint > 7) { - leftOfPoint = data[i] & 0x70 >> 4; - sign = -1; - } - rightOfPoint = (data[i] & 0x0f); - break; - } - dimmInfo->dataInputHoldTime = - (leftOfPoint * 100 + rightOfPoint) * sign; - debug("Data Input Hold Time [ns]: %d.%d\n\n", - sign * leftOfPoint, rightOfPoint); - break; -/*------------------------------------------------------------------------------------------------------------------------------*/ - } - } - /* calculating the sdram density */ - for (i = 0; - i < dimmInfo->numOfRowAddresses + dimmInfo->numOfColAddresses; - i++) { - density = density * 2; - } - dimmInfo->deviceDensity = density * dimmInfo->numOfBanksOnEachDevice * - dimmInfo->sdramWidth; - dimmInfo->numberOfDevices = - (dimmInfo->dataWidth / dimmInfo->sdramWidth) * - dimmInfo->numOfModuleBanks; - devicesForErrCheck = - (dimmInfo->dataWidth - 64) / dimmInfo->sdramWidth; - if ((dimmInfo->errorCheckType == 0x1) - || (dimmInfo->errorCheckType == 0x2) - || (dimmInfo->errorCheckType == 0x3)) { - dimmInfo->size = - (dimmInfo->deviceDensity / 8) * - (dimmInfo->numberOfDevices - devicesForErrCheck); - } else { - dimmInfo->size = - (dimmInfo->deviceDensity / 8) * - dimmInfo->numberOfDevices; - } - - /* compute the module DRB size */ - tmp = (1 << - (dimmInfo->numOfRowAddresses + dimmInfo->numOfColAddresses)); - tmp *= dimmInfo->numOfModuleBanks; - tmp *= dimmInfo->sdramWidth; - tmp = tmp >> 24; /* div by 0x4000000 (64M) */ - dimmInfo->drb_size = (uchar) tmp; - debug("Module DRB size (n*64Mbit): %d\n", dimmInfo->drb_size); - - /* try a CAS latency of 3 first... */ - - /* bit 1 is CL2, bit 2 is CL3 */ - supp_cal = (dimmInfo->suportedCasLatencies & 0x1c) >> 1; - - cal_val = 0; - if (supp_cal & 8) { - if (NS10to10PS (data[9]) <= tmemclk) - cal_val = 6; - } - if (supp_cal & 4) { - if (NS10to10PS (data[9]) <= tmemclk) - cal_val = 5; - } - - /* then 2... */ - if (supp_cal & 2) { - if (NS10to10PS (data[23]) <= tmemclk) - cal_val = 4; - } - - debug("cal_val = %d\n", cal_val * 5); - - /* bummer, did't work... */ - if (cal_val == 0) { - debug("Couldn't find a good CAS latency\n"); - hang (); - return 0; - } - - return true; -} - -/* sets up the GT properly with information passed in */ -int setup_sdram (AUX_MEM_DIMM_INFO * info) -{ - ulong tmp; - ulong tmp_sdram_mode = 0; /* 0x141c */ - ulong tmp_dunit_control_low = 0; /* 0x1404 */ - uint sdram_config_reg = CONFIG_SYS_SDRAM_CONFIG; - int i; - - /* sanity checking */ - if (!info->numOfModuleBanks) { - printf ("setup_sdram called with 0 banks\n"); - return 1; - } - - /* delay line */ - - /* Program the GT with the discovered data */ - if (info->registeredAddrAndControlInputs == true) - debug("Module is registered, but we do not support registered Modules !!!\n"); - - /* delay line */ - set_dfcdlInit (); /* may be its not needed */ - debug("Delay line set done\n"); - - /* set SDRAM mode NOP */ /* To_do check it */ - GT_REG_WRITE (SDRAM_OPERATION, 0x5); - while (GTREGREAD (SDRAM_OPERATION) != 0) { - debug("\n*** SDRAM_OPERATION 1418: Module still busy ... please wait... ***\n"); - } - -#ifdef CONFIG_MV64360_ECC - if ((info->errorCheckType == 0x2) && (CPCI750_ECC_TEST)) { - /* DRAM has ECC, so turn it on */ - sdram_config_reg |= BIT18; - debug("Enabling ECC\n"); - } -#endif /* of ifdef CONFIG_MV64360_ECC */ - - /* SDRAM configuration */ - GT_REG_WRITE(SDRAM_CONFIG, sdram_config_reg); - debug("sdram_conf 0x1400: %08x\n", GTREGREAD (SDRAM_CONFIG)); - - /* SDRAM open pages controll keep open as much as I can */ - GT_REG_WRITE (SDRAM_OPEN_PAGES_CONTROL, 0x0); - debug("sdram_open_pages_controll 0x1414: %08x\n", - GTREGREAD (SDRAM_OPEN_PAGES_CONTROL)); - - - /* SDRAM D_UNIT_CONTROL_LOW 0x1404 */ - tmp = (GTREGREAD (D_UNIT_CONTROL_LOW) & 0x01); /* Clock Domain Sync from power on reset */ - if (tmp == 0) - debug("Core Signals are sync (by HW-Setting)!!!\n"); - else - debug("Core Signals syncs. are bypassed (by HW-Setting)!!!\n"); - - /* SDRAM set CAS Lentency according to SPD information */ - switch (info->memoryType) { - case SDRAM: - debug("### SD-RAM not supported yet !!!\n"); - hang (); - /* ToDo fill SD-RAM if needed !!!!! */ - break; - - case DDR: - debug("### SET-CL for DDR-RAM\n"); - - switch (info->maxClSupported_DDR) { - case DDR_CL_3: - tmp_dunit_control_low = 0x3c000000; /* Read-Data sampled on falling edge of Clk */ - tmp_sdram_mode = 0x32; /* CL=3 Burstlength = 4 */ - debug("Max. CL is 3 CLKs 0x141c= %08lx, 0x1404 = %08lx\n", - tmp_sdram_mode, tmp_dunit_control_low); - break; - - case DDR_CL_2_5: - if (tmp == 1) { /* clocks sync */ - tmp_dunit_control_low = 0x24000000; /* Read-Data sampled on falling edge of Clk */ - tmp_sdram_mode = 0x62; /* CL=2,5 Burstlength = 4 */ - debug("Max. CL is 2,5s CLKs 0x141c= %08lx, 0x1404 = %08lx\n", - tmp_sdram_mode, tmp_dunit_control_low); - } else { /* clk sync. bypassed */ - - tmp_dunit_control_low = 0x03000000; /* Read-Data sampled on rising edge of Clk */ - tmp_sdram_mode = 0x62; /* CL=2,5 Burstlength = 4 */ - debug("Max. CL is 2,5 CLKs 0x141c= %08lx, 0x1404 = %08lx\n", - tmp_sdram_mode, tmp_dunit_control_low); - } - break; - - case DDR_CL_2: - if (tmp == 1) { /* Sync */ - tmp_dunit_control_low = 0x03000000; /* Read-Data sampled on rising edge of Clk */ - tmp_sdram_mode = 0x22; /* CL=2 Burstlength = 4 */ - debug("Max. CL is 2s CLKs 0x141c= %08lx, 0x1404 = %08lx\n", - tmp_sdram_mode, tmp_dunit_control_low); - } else { /* Not sync. */ - - tmp_dunit_control_low = 0x3b000000; /* Read-Data sampled on rising edge of Clk */ - tmp_sdram_mode = 0x22; /* CL=2 Burstlength = 4 */ - debug("Max. CL is 2 CLKs 0x141c= %08lx, 0x1404 = %08lx\n", - tmp_sdram_mode, tmp_dunit_control_low); - } - break; - - case DDR_CL_1_5: - if (tmp == 1) { /* Sync */ - tmp_dunit_control_low = 0x23000000; /* Read-Data sampled on falling edge of Clk */ - tmp_sdram_mode = 0x52; /* CL=1,5 Burstlength = 4 */ - debug("Max. CL is 1,5s CLKs 0x141c= %08lx, 0x1404 = %08lx\n", - tmp_sdram_mode, tmp_dunit_control_low); - } else { /* not sync */ - - tmp_dunit_control_low = 0x1a000000; /* Read-Data sampled on rising edge of Clk */ - tmp_sdram_mode = 0x52; /* CL=1,5 Burstlength = 4 */ - debug("Max. CL is 1,5 CLKs 0x141c= %08lx, 0x1404 = %08lx\n", - tmp_sdram_mode, tmp_dunit_control_low); - } - break; - - default: - printf ("Max. CL is out of range %d\n", - info->maxClSupported_DDR); - hang (); - break; - } - break; - } - - /* Write results of CL detection procedure */ - GT_REG_WRITE (SDRAM_MODE, tmp_sdram_mode); - /* set SDRAM mode SetCommand 0x1418 */ - GT_REG_WRITE (SDRAM_OPERATION, 0x3); - while (GTREGREAD (SDRAM_OPERATION) != 0) { - debug("\n*** SDRAM_OPERATION 1418 after SDRAM_MODE: Module still busy ... please wait... ***\n"); - } - - - /* SDRAM D_UNIT_CONTROL_LOW 0x1404 */ - tmp = (GTREGREAD (D_UNIT_CONTROL_LOW) & 0x01); /* Clock Domain Sync from power on reset */ - if (tmp != 1) { /*clocks are not sync */ - /* asyncmode */ - GT_REG_WRITE (D_UNIT_CONTROL_LOW, - (GTREGREAD (D_UNIT_CONTROL_LOW) & 0x7F) | - 0x18110780 | tmp_dunit_control_low); - } else { - /* syncmode */ - GT_REG_WRITE (D_UNIT_CONTROL_LOW, - (GTREGREAD (D_UNIT_CONTROL_LOW) & 0x7F) | - 0x00110000 | tmp_dunit_control_low); - } - - /* set SDRAM mode SetCommand 0x1418 */ - GT_REG_WRITE (SDRAM_OPERATION, 0x3); - while (GTREGREAD (SDRAM_OPERATION) != 0) { - debug("\n*** SDRAM_OPERATION 1418 after D_UNIT_CONTROL_LOW: Module still busy ... please wait... ***\n"); - } - -/*------------------------------------------------------------------------------ */ - - - /* bank parameters */ - /* SDRAM address decode register */ - /* program this with the default value */ - tmp = 0x02; - - - debug("drb_size (n*64Mbit): %d\n", info->drb_size); - switch (info->drb_size) { - case 1: /* 64 Mbit */ - case 2: /* 128 Mbit */ - debug("RAM-Device_size 64Mbit or 128Mbit)\n"); - tmp |= (0x00 << 4); - break; - case 4: /* 256 Mbit */ - case 8: /* 512 Mbit */ - debug("RAM-Device_size 256Mbit or 512Mbit)\n"); - tmp |= (0x01 << 4); - break; - case 16: /* 1 Gbit */ - case 32: /* 2 Gbit */ - debug("RAM-Device_size 1Gbit or 2Gbit)\n"); - tmp |= (0x02 << 4); - break; - default: - printf ("Error in dram size calculation\n"); - debug("Assume: RAM-Device_size 1Gbit or 2Gbit)\n"); - tmp |= (0x02 << 4); - return 1; - } - - /* SDRAM bank parameters */ - /* the param registers for slot 1 (banks 2+3) are offset by 0x8 */ - debug("setting up slot %d config with: %08lx \n", info->slot, tmp); - GT_REG_WRITE (SDRAM_ADDR_CONTROL, tmp); - -/* ------------------------------------------------------------------------------ */ - - debug("setting up sdram_timing_control_low with: %08x \n", - 0x11511220); - GT_REG_WRITE (SDRAM_TIMING_CONTROL_LOW, 0x11511220); - - -/* ------------------------------------------------------------------------------ */ - - /* SDRAM configuration */ - tmp = GTREGREAD (SDRAM_CONFIG); - - if (info->registeredAddrAndControlInputs - || info->registeredDQMBinputs) { - tmp |= (1 << 17); - debug("SPD says: registered Addr. and Cont.: %d; registered DQMBinputs: %d\n", - info->registeredAddrAndControlInputs, - info->registeredDQMBinputs); - } - - /* Use buffer 1 to return read data to the CPU - * Page 426 MV64360 */ - tmp |= (1 << 26); - debug("Before Buffer assignment - sdram_conf: %08x\n", - GTREGREAD (SDRAM_CONFIG)); - debug("After Buffer assignment - sdram_conf: %08x\n", - GTREGREAD (SDRAM_CONFIG)); - - /* SDRAM timing To_do: */ - - - tmp = GTREGREAD (SDRAM_TIMING_CONTROL_HIGH); - debug("# sdram_timing_control_high is : %08lx \n", tmp); - - /* SDRAM address decode register */ - /* program this with the default value */ - tmp = GTREGREAD (SDRAM_ADDR_CONTROL); - debug("SDRAM address control (before: decode): %08x ", - GTREGREAD (SDRAM_ADDR_CONTROL)); - GT_REG_WRITE (SDRAM_ADDR_CONTROL, (tmp | 0x2)); - debug("SDRAM address control (after: decode): %08x\n", - GTREGREAD (SDRAM_ADDR_CONTROL)); - - /* set the SDRAM configuration for each bank */ - -/* for (i = info->slot * 2; i < ((info->slot * 2) + info->banks); i++) */ - { - int l, l1; - - i = info->slot; - debug("\n*** Running a MRS cycle for bank %d ***\n", i); - - /* map the bank */ - memory_map_bank (i, 0, GB / 4); -#if 1 /* test only */ - - tmp = GTREGREAD (SDRAM_MODE); - GT_REG_WRITE (EXTENDED_DRAM_MODE, 0x0); - GT_REG_WRITE (SDRAM_OPERATION, 0x4); - while (GTREGREAD (SDRAM_OPERATION) != 0) { - debug("\n*** SDRAM_OPERATION 1418 after SDRAM_MODE: Module still busy ... please wait... ***\n"); - } - - GT_REG_WRITE (SDRAM_MODE, tmp | 0x80); - GT_REG_WRITE (SDRAM_OPERATION, 0x3); - while (GTREGREAD (SDRAM_OPERATION) != 0) { - debug("\n*** SDRAM_OPERATION 1418 after SDRAM_MODE: Module still busy ... please wait... ***\n"); - } - l1 = 0; - for (l=0;l<200;l++) - l1 += GTREGREAD (SDRAM_OPERATION); - - GT_REG_WRITE (SDRAM_MODE, tmp); - GT_REG_WRITE (SDRAM_OPERATION, 0x3); - while (GTREGREAD (SDRAM_OPERATION) != 0) { - debug("\n*** SDRAM_OPERATION 1418 after SDRAM_MODE: Module still busy ... please wait... ***\n"); - } - - /* switch back to normal operation mode */ - GT_REG_WRITE (SDRAM_OPERATION, 0x5); - while (GTREGREAD (SDRAM_OPERATION) != 0) { - debug("\n*** SDRAM_OPERATION 1418 after SDRAM_MODE: Module still busy ... please wait... ***\n"); - } - -#endif /* test only */ - /* unmap the bank */ - memory_map_bank (i, 0, 0); - } - - return 0; -} - -/* - * Check memory range for valid RAM. A simple memory test determines - * the actually available RAM size between addresses `base' and - * `base + maxsize'. Some (not all) hardware errors are detected: - * - short between address lines - * - short between data lines - */ -long int -dram_size(long int *base, long int maxsize) -{ - volatile long int *addr, *b=base; - long int cnt, val, save1, save2; - -#define STARTVAL (1<<20) /* start test at 1M */ - for (cnt = STARTVAL/sizeof(long); cnt < maxsize/sizeof(long); cnt <<= 1) { - addr = base + cnt; /* pointer arith! */ - - save1 = *addr; /* save contents of addr */ - save2 = *b; /* save contents of base */ - - *addr=cnt; /* write cnt to addr */ - *b=0; /* put null at base */ - - /* check at base address */ - if ((*b) != 0) { - *addr=save1; /* restore *addr */ - *b=save2; /* restore *b */ - return (0); - } - val = *addr; /* read *addr */ - val = *addr; /* read *addr */ - - *addr=save1; - *b=save2; - - if (val != cnt) { - debug("Found %08x at Address %08x (failure)\n", (unsigned int)val, (unsigned int) addr); - /* fix boundary condition.. STARTVAL means zero */ - if(cnt==STARTVAL/sizeof(long)) cnt=0; - return (cnt * sizeof(long)); - } - } - return maxsize; -} - -#ifdef CONFIG_MV64360_ECC -/* - * mv_dma_is_channel_active: - * Checks if a engine is busy. - */ -int mv_dma_is_channel_active(int engine) -{ - ulong data; - - data = GTREGREAD(MV64360_DMA_CHANNEL0_CONTROL + 4 * engine); - if (data & BIT14) /* activity status */ - return 1; - - return 0; -} - -/* - * mv_dma_set_memory_space: - * Set a DMA memory window for the DMA's address decoding map. - */ -int mv_dma_set_memory_space(ulong mem_space, ulong mem_space_target, - ulong mem_space_attr, ulong base_address, - ulong size) -{ - ulong temp; - - /* The base address must be aligned to the size. */ - if (base_address % size != 0) - return 0; - - if (size >= 0x10000) { - size &= 0xffff0000; - base_address = (base_address & 0xffff0000); - /* Set the new attributes */ - GT_REG_WRITE(MV64360_DMA_BASE_ADDR_REG0 + mem_space * 8, - (base_address | mem_space_target | - mem_space_attr)); - GT_REG_WRITE((MV64360_DMA_SIZE_REG0 + mem_space * 8), - (size - 1) & 0xffff0000); - temp = GTREGREAD(MV64360_DMA_BASE_ADDR_ENABLE_REG); - GT_REG_WRITE(DMA_BASE_ADDR_ENABLE_REG, - (temp & ~(BIT0 << mem_space))); - return 1; - } - - return 0; -} - - -/* - * mv_dma_transfer: - * Transfer data from source_addr to dest_addr on one of the 4 DMA channels. - */ -int mv_dma_transfer(int engine, ulong source_addr, - ulong dest_addr, ulong bytes, ulong command) -{ - ulong eng_off_reg; /* Engine Offset Register */ - - if (bytes > 0xffff) - command = command | BIT31; /* DMA_16M_DESCRIPTOR_MODE */ - - command = command | ((command >> 6) & 0x7); - eng_off_reg = engine * 4; - GT_REG_WRITE(MV64360_DMA_CHANNEL0_BYTE_COUNT + eng_off_reg, - bytes); - GT_REG_WRITE(MV64360_DMA_CHANNEL0_SOURCE_ADDR + eng_off_reg, - source_addr); - GT_REG_WRITE(MV64360_DMA_CHANNEL0_DESTINATION_ADDR + eng_off_reg, - dest_addr); - command |= BIT12 /* DMA_CHANNEL_ENABLE */ - | BIT9; /* DMA_NON_CHAIN_MODE */ - - /* Activate DMA engine By writting to mv_dma_control_register */ - GT_REG_WRITE(MV64360_DMA_CHANNEL0_CONTROL + eng_off_reg, command); - - return 1; -} -#endif /* of ifdef CONFIG_MV64360_ECC */ - -/* ppcboot interface function to SDRAM init - this is where all the - * controlling logic happens */ -phys_size_t -initdram(int board_type) -{ - int checkbank[4] = { [0 ... 3] = 0 }; - ulong realsize, total, check; - AUX_MEM_DIMM_INFO dimmInfo1; - AUX_MEM_DIMM_INFO dimmInfo2; - int bank_no, nhr; -#ifdef CONFIG_MV64360_ECC - ulong dest, mem_space_attr; -#endif /* of ifdef CONFIG_MV64360_ECC */ - - /* first, use the SPD to get info about the SDRAM/ DDRRAM */ - - /* check the NHR bit and skip mem init if it's already done */ - nhr = get_hid0() & (1 << 16); - - if (nhr) { - printf("Skipping SD- DDRRAM setup due to NHR bit being set\n"); - } else { - /* DIMM0 */ - (void)check_dimm(0, &dimmInfo1); - - /* DIMM1 */ - (void)check_dimm(1, &dimmInfo2); - - memory_map_bank(0, 0, 0); - memory_map_bank(1, 0, 0); - memory_map_bank(2, 0, 0); - memory_map_bank(3, 0, 0); - - if (dimmInfo1.numOfModuleBanks && setup_sdram(&dimmInfo1)) { - printf("Setup for DIMM1 failed.\n"); - } - - if (dimmInfo2.numOfModuleBanks && setup_sdram(&dimmInfo2)) { - printf("Setup for DIMM2 failed.\n"); - } - - /* set the NHR bit */ - set_hid0(get_hid0() | (1 << 16)); - } - /* next, size the SDRAM banks */ - - realsize = total = 0; - check = GB/4; - if (dimmInfo1.numOfModuleBanks > 0) {checkbank[0] = 1; printf("-- DIMM1 has 1 bank\n");} - if (dimmInfo1.numOfModuleBanks > 1) {checkbank[1] = 1; printf("-- DIMM1 has 2 banks\n");} - if (dimmInfo1.numOfModuleBanks > 2) - printf("Error, SPD claims DIMM1 has >2 banks\n"); - - if (dimmInfo2.numOfModuleBanks > 0) {checkbank[2] = 1; printf("-- DIMM2 has 1 bank\n");} - if (dimmInfo2.numOfModuleBanks > 1) {checkbank[3] = 1; printf("-- DIMM2 has 2 banks\n");} - if (dimmInfo2.numOfModuleBanks > 2) - printf("Error, SPD claims DIMM2 has >2 banks\n"); - - for (bank_no = 0; bank_no < CONFIG_SYS_DRAM_BANKS; bank_no++) { - /* skip over banks that are not populated */ - if (! checkbank[bank_no]) - continue; - - if ((total + check) > CONFIG_SYS_GT_REGS) - check = CONFIG_SYS_GT_REGS - total; - - memory_map_bank(bank_no, total, check); - realsize = dram_size((long int *)total, check); - memory_map_bank(bank_no, total, realsize); - -#ifdef CONFIG_MV64360_ECC - if (((dimmInfo1.errorCheckType != 0) && - ((dimmInfo2.errorCheckType != 0) || - (dimmInfo2.numOfModuleBanks == 0))) && - (CPCI750_ECC_TEST)) { - printf("ECC Initialization of Bank %d:", bank_no); - mem_space_attr = ((~(BIT0 << bank_no)) & 0xf) << 8; - mv_dma_set_memory_space(0, 0, mem_space_attr, total, - realsize); - for (dest = total; dest < total + realsize; - dest += _8M) { - mv_dma_transfer(0, total, dest, _8M, - BIT8 | /* DMA_DTL_128BYTES */ - BIT3 | /* DMA_HOLD_SOURCE_ADDR */ - BIT11); /* DMA_BLOCK_TRANSFER_MODE */ - while (mv_dma_is_channel_active(0)) - ; - } - printf(" PASS\n"); - } -#endif /* of ifdef CONFIG_MV64360_ECC */ - - total += realsize; - } - -/* Setup Ethernet DMA Adress window to DRAM Area */ - return(total); -} - -/* *************************************************************************************** -! * SDRAM INIT * -! * This procedure detect all Sdram types: 64, 128, 256, 512 Mbit, 1Gbit and 2Gb * -! * This procedure fits only the Atlantis * -! * * -! *************************************************************************************** */ - - -/* *************************************************************************************** -! * DFCDL initialize MV643xx Design Considerations * -! * * -! *************************************************************************************** */ -int set_dfcdlInit (void) -{ - int i; - unsigned int dfcdl_word = 0x0000014f; - - for (i = 0; i < 64; i++) { - GT_REG_WRITE (SRAM_DATA0, dfcdl_word); - } - GT_REG_WRITE (DFCDL_CONFIG0, 0x00300000); /* enable dynamic delay line updating */ - - - return (0); -} - -int do_show_ecc(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) -{ - unsigned int ecc_counter; - unsigned int ecc_addr; - - GT_REG_READ(0x1458, &ecc_counter); - GT_REG_READ(0x1450, &ecc_addr); - GT_REG_WRITE(0x1450, 0); - - printf("Error Counter since Reset: %8d\n", ecc_counter); - printf("Last error address :0x%08x (" , ecc_addr & 0xfffffff8); - if (ecc_addr & 0x01) - printf("double"); - else - printf("single"); - printf(" bit) at DDR-RAM CS#%d\n", ((ecc_addr & 0x6) >> 1)); - - return 0; -} - - -U_BOOT_CMD( - show_ecc, 1, 1, do_show_ecc, - "Show Marvell MV64360 ECC Info", - "Show Marvell MV64360 ECC Counter and last error." -); |