diff options
Diffstat (limited to 'board/enbw')
| -rw-r--r-- | board/enbw/enbw_cmc/enbw_cmc.c | 347 |
1 files changed, 322 insertions, 25 deletions
diff --git a/board/enbw/enbw_cmc/enbw_cmc.c b/board/enbw/enbw_cmc/enbw_cmc.c index 6c0d931..0874e9c 100644 --- a/board/enbw/enbw_cmc/enbw_cmc.c +++ b/board/enbw/enbw_cmc/enbw_cmc.c @@ -35,6 +35,8 @@ #include <mmc.h> #include <net.h> #include <netdev.h> +#include <spi.h> +#include <linux/ctype.h> #include <asm/gpio.h> #include <asm/io.h> #include <asm/arch/da850_lowlevel.h> @@ -86,16 +88,22 @@ static const struct pinmux_config enbw_pins[] = { { pinmux(5), 1, 0 }, { pinmux(5), 1, 3 }, { pinmux(5), 1, 7 }, - { pinmux(6), 1, 0 }, - { pinmux(6), 1, 1 }, + { pinmux(5), 1, 5 }, + { pinmux(5), 1, 4 }, + { pinmux(5), 1, 3 }, + { pinmux(5), 1, 2 }, + { pinmux(5), 1, 1 }, + { pinmux(5), 1, 0 }, + { pinmux(6), 8, 0 }, + { pinmux(6), 8, 1 }, { pinmux(6), 8, 2 }, { pinmux(6), 8, 3 }, - { pinmux(6), 1, 4 }, + { pinmux(6), 8, 4 }, { pinmux(6), 8, 5 }, { pinmux(6), 1, 7 }, { pinmux(7), 8, 2 }, { pinmux(7), 1, 3 }, - { pinmux(7), 1, 6 }, + { pinmux(7), 8, 6 }, { pinmux(7), 1, 7 }, { pinmux(13), 8, 2 }, { pinmux(13), 8, 3 }, @@ -163,24 +171,37 @@ struct gpio_config { unsigned char value; }; -static const struct gpio_config enbw_gpio_config[] = { +static const struct gpio_config enbw_gpio_config_hut[] = { + { "RS485 enable", 8, 11, 1, 0 }, + { "RS485 iso", 8, 10, 1, 1 }, + { "W2HUT RS485 Rx ena", 8, 9, 1, 0 }, + { "W2HUT RS485 iso", 8, 8, 1, 1 }, +}; + +static const struct gpio_config enbw_gpio_config_w[] = { { "RS485 enable", 8, 11, 1, 0 }, { "RS485 iso", 8, 10, 1, 0 }, { "W2HUT RS485 Rx ena", 8, 9, 1, 0 }, { "W2HUT RS485 iso", 8, 8, 1, 0 }, +}; + +static const struct gpio_config enbw_gpio_config[] = { { "LAN reset", 7, 15, 1, 1 }, { "ena 11V PLC", 7, 14, 1, 0 }, { "ena 1.5V PLC", 7, 13, 1, 0 }, { "disable VBUS", 7, 12, 1, 1 }, - { "PLC reset", 6, 13, 1, 1 }, + { "PLC reset", 6, 13, 1, 0 }, { "LCM RS", 6, 12, 1, 0 }, { "LCM R/W", 6, 11, 1, 0 }, { "PLC pairing", 6, 10, 1, 1 }, { "PLC MDIO CLK", 6, 9, 1, 0 }, { "HK218", 6, 8, 1, 0 }, { "HK218 Rx", 6, 1, 1, 1 }, - { "TPM reset", 6, 0, 1, 1 }, - { "LCM E", 2, 2, 1, 1 }, + { "TPM reset", 6, 0, 1, 0 }, + { "Board-Type", 3, 9, 0, 0 }, + { "HW-ID0", 2, 7, 0, 0 }, + { "HW-ID1", 2, 6, 0, 0 }, + { "HW-ID2", 2, 3, 0, 0 }, { "PV-IF RxD ena", 0, 15, 1, 1 }, { "LED1", 1, 15, 1, 1 }, { "LED2", 0, 1, 1, 1 }, @@ -229,34 +250,57 @@ static void enbw_cmc_switch(int port, int on) } } -int board_init(void) +static int enbw_cmc_init_gpio(const struct gpio_config *conf, int sz) { int i, ret; -#ifndef CONFIG_USE_IRQ - irq_init(); -#endif - /* address of boot parameters, not used as booting with DTT */ - gd->bd->bi_boot_params = 0; + for (i = 0; i < sz; i++) { + int gpio = conf[i].bank * 16 + + conf[i].gpio; - for (i = 0; i < ARRAY_SIZE(enbw_gpio_config); i++) { - int gpio = enbw_gpio_config[i].bank * 16 + - enbw_gpio_config[i].gpio; - - ret = gpio_request(gpio, enbw_gpio_config[i].name); + ret = gpio_request(gpio, conf[i].name); if (ret) { printf("%s: Could not get %s gpio\n", __func__, - enbw_gpio_config[i].name); - return -1; + conf[i].name); + return ret; } - if (enbw_gpio_config[i].out) + if (conf[i].out) gpio_direction_output(gpio, - enbw_gpio_config[i].value); + conf[i].value); else gpio_direction_input(gpio); } + return 0; +} + +int board_init(void) +{ + int board_type, hw_id; + +#ifndef CONFIG_USE_IRQ + irq_init(); +#endif + /* address of boot parameters, not used as booting with DTT */ + gd->bd->bi_boot_params = 0; + + enbw_cmc_init_gpio(enbw_gpio_config, ARRAY_SIZE(enbw_gpio_config)); + + /* detect HW version */ + board_type = gpio_get_value(CONFIG_ENBW_CMC_BOARD_TYPE); + hw_id = gpio_get_value(CONFIG_ENBW_CMC_HW_ID_BIT0) + + (gpio_get_value(CONFIG_ENBW_CMC_HW_ID_BIT1) << 1) + + (gpio_get_value(CONFIG_ENBW_CMC_HW_ID_BIT2) << 2); + printf("BOARD: CMC-%s hw id: %d\n", (board_type ? "w2" : "hut"), + hw_id); + if (board_type) + enbw_cmc_init_gpio(enbw_gpio_config_w, + ARRAY_SIZE(enbw_gpio_config_w)); + else + enbw_cmc_init_gpio(enbw_gpio_config_hut, + ARRAY_SIZE(enbw_gpio_config_hut)); + /* setup the SUSPSRC for ARM to control emulation suspend */ clrbits_le32(&davinci_syscfg_regs->suspsrc, (DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C | @@ -267,14 +311,231 @@ int board_init(void) } #ifdef CONFIG_DRIVER_TI_EMAC + +#define KSZ_CMD_READ 0x03 +#define KSZ_CMD_WRITE 0x02 +#define KSZ_ID 0x95 + +static int enbw_cmc_switch_read(struct spi_slave *spi, u8 reg, u8 *val) +{ + unsigned long flags = SPI_XFER_BEGIN; + int ret; + int cmd_len; + u8 cmd[2]; + + cmd[0] = KSZ_CMD_READ; + cmd[1] = reg; + cmd_len = 2; + + ret = spi_xfer(spi, cmd_len * 8, cmd, NULL, flags); + if (ret) { + debug("Failed to send command (%zu bytes): %d\n", + cmd_len, ret); + return -EINVAL; + } + flags |= SPI_XFER_END; + *val = 0; + cmd_len = 1; + ret = spi_xfer(spi, cmd_len * 8, NULL, val, flags); + if (ret) { + debug("Failed to read (%zu bytes): %d\n", + cmd_len, ret); + return -EINVAL; + } + + return 0; +} + +static int enbw_cmc_switch_read_ident(struct spi_slave *spi) +{ + int ret; + u8 val; + + ret = enbw_cmc_switch_read(spi, 0, &val); + if (ret) { + debug("Failed to read\n"); + return -EINVAL; + } + + if (val != KSZ_ID) + return -EINVAL; + + return 0; +} + +static int enbw_cmc_switch_write(struct spi_slave *spi, unsigned long reg, + unsigned long val) +{ + unsigned long flags = SPI_XFER_BEGIN; + int ret; + int cmd_len; + u8 cmd[3]; + + cmd[0] = KSZ_CMD_WRITE; + cmd[1] = reg; + cmd[2] = val; + cmd_len = 3; + flags |= SPI_XFER_END; + + ret = spi_xfer(spi, cmd_len * 8, cmd, NULL, flags); + if (ret) { + debug("Failed to send command (%zu bytes): %d\n", + cmd_len, ret); + return -EINVAL; + } + + udelay(1000); + ret = enbw_cmc_switch_read(spi, reg, &cmd[0]); + if (ret) { + debug("Failed to read\n"); + return -EINVAL; + } + if (val != cmd[0]) + debug("warning: reg: %lx va: %x soll: %lx\n", + reg, cmd[0], val); + + return 0; +} + +static int enbw_cmc_eof(unsigned char *ptr) +{ + if (*ptr == 0xff) + return 1; + + return 0; +} + +static char *enbw_cmc_getnewline(char *ptr) +{ + while (*ptr != 0x0a) { + ptr++; + if (enbw_cmc_eof((unsigned char *)ptr)) + return NULL; + } + + ptr++; + return ptr; +} + +static char *enbw_cmc_getvalue(char *ptr, int *value) +{ + int end = 0; + + *value = -EINVAL; + + if (!isxdigit(*ptr)) + end = 1; + + while (end) { + if ((*ptr == '#') || (*ptr == ';')) { + ptr = enbw_cmc_getnewline(ptr); + return ptr; + } + if (ptr != NULL) { + if (isxdigit(*ptr)) { + end = 0; + } else if (*ptr == 0x0a) { + ptr++; + return ptr; + } else { + ptr++; + if (enbw_cmc_eof((unsigned char *)ptr)) + return NULL; + } + } else { + return NULL; + } + } + *value = (int)simple_strtoul((const char *)ptr, &ptr, 16); + ptr++; + return ptr; +} + +static int enbw_cmc_config_switch(unsigned long addr) +{ + struct spi_slave *spi; + char *ptr = (char *)addr; + int value, reg; + int ret; + int bus, cs, max_hz, spi_mode; + + debug("configure switch with file on addr: 0x%lx\n", addr); + + bus = 0; + cs = 0; + max_hz = 1000000; + spi_mode = 0; + + spi = spi_setup_slave(bus, cs, max_hz, spi_mode); + if (!spi) { + printf("Failed to set up slave\n"); + return -EINVAL; + } + + ret = spi_claim_bus(spi); + if (ret) { + debug("Failed to claim SPI bus: %d\n", ret); + goto err_claim_bus; + } + + ret = enbw_cmc_switch_read_ident(spi); + if (ret) + goto err_claim_bus; + + ptr = (char *)addr; + while (ptr != NULL) { + ptr = enbw_cmc_getvalue(ptr, ®); + if (ptr != NULL) { + ptr = enbw_cmc_getvalue(ptr, &value); + if ((ptr != NULL) && (value >= 0)) + if (enbw_cmc_switch_write(spi, reg, value)) + goto err_read; + } + } + return 0; + +err_read: + spi_release_bus(spi); +err_claim_bus: + spi_free_slave(spi); + return -EINVAL; +} + +static int do_switch(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[]) +{ + unsigned long addr; + + if (argc < 2) + return cmd_usage(cmdtp); + + addr = simple_strtoul(argv[1], NULL, 16); + enbw_cmc_config_switch(addr); + + return 0; +} + +U_BOOT_CMD(switch, 3, 1, do_switch, + "switch addr", + "[addr]" +); + /* * Initializes on-board ethernet controllers. */ int board_eth_init(bd_t *bis) { -#ifdef CONFIG_DRIVER_TI_EMAC + const char *s; + size_t len; + davinci_emac_mii_mode_sel(0); -#endif /* CONFIG_DRIVER_TI_EMAC */ + + /* send a config file to the switch */ + s = hwconfig_subarg("switch", "config", &len); + if (len) { + unsigned long addr = simple_strtoul(s, NULL, 16); + + enbw_cmc_config_switch(addr); + } if (!davinci_emac_initialize()) { printf("Error: Ethernet init failed!\n"); @@ -546,6 +807,29 @@ ulong bootcount_load(void) } #endif +ulong post_word_load(void) +{ + struct davinci_rtc *reg = + (struct davinci_rtc *)CONFIG_SYS_POST_WORD_ADDR; + + return in_be32(®->scratch2); +} + +void post_word_store(ulong value) +{ + struct davinci_rtc *reg = + (struct davinci_rtc *)CONFIG_SYS_POST_WORD_ADDR; + + /* + * write RTC kick register to enable write + * for RTC Scratch registers. Cratch0 and 1 are + * used for bootcount values. + */ + writel(RTC_KICK0R_WE, ®->kick0r); + writel(RTC_KICK1R_WE, ®->kick1r); + out_be32(®->scratch2, value); +} + void board_gpio_init(void) { struct davinci_gpio *gpio = davinci_gpio_bank01; @@ -558,6 +842,19 @@ void board_gpio_init(void) clrbits_le32(&gpio->out_data, 0x8000407e); /* set LED 1 - 5 to state on */ setbits_le32(&gpio->out_data, 0x8000001e); + + /* + * set some gpio pins to low, this is needed early, + * so we have no gpio Interface here + * gpios: + * 8[8] Mode PV select low + * 8[9] Debug Rx Enable low + * 8[10] Mode Select PV low + * 8[11] Counter Interface RS485 Rx-Enable low + */ + gpio = davinci_gpio_bank8; + clrbits_le32(&gpio->dir, 0x00000f00); + clrbits_le32(&gpio->out_data, 0x0f00); } int board_late_init(void) |