diff options
Diffstat (limited to 'board/compulab/cm_t35/cm_t35.c')
-rw-r--r-- | board/compulab/cm_t35/cm_t35.c | 32 |
1 files changed, 30 insertions, 2 deletions
diff --git a/board/compulab/cm_t35/cm_t35.c b/board/compulab/cm_t35/cm_t35.c index b9a9965..00bcf41 100644 --- a/board/compulab/cm_t35/cm_t35.c +++ b/board/compulab/cm_t35/cm_t35.c @@ -105,6 +105,22 @@ static inline int splash_load_from_nand(void) } #endif /* CONFIG_CMD_NAND */ +#ifdef CONFIG_SPL_BUILD +/* + * Routine: get_board_mem_timings + * Description: If we use SPL then there is no x-loader nor config header + * so we have to setup the DDR timings ourself on both banks. + */ +void get_board_mem_timings(struct board_sdrc_timings *timings) +{ + timings->mr = MICRON_V_MR_165; + timings->mcfg = MICRON_V_MCFG_200(256 << 20); /* raswidth 14 needed */ + timings->ctrla = MICRON_V_ACTIMA_165; + timings->ctrlb = MICRON_V_ACTIMB_165; + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz; +} +#endif + int splash_screen_prepare(void) { char *env_splashimage_value; @@ -268,6 +284,9 @@ static void cm_t3x_set_common_muxconf(void) /* DVI enable */ MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | DIS | M4));/*GPMC_nCS3*/ + /* DataImage backlight */ + MUX_VAL(CP(GPMC_NCS7), (IDIS | PTU | DIS | M4));/*GPIO_58*/ + /* CM-T3x Ethernet */ MUX_VAL(CP(GPMC_NCS5), (IDIS | PTU | DIS | M0)); /*GPMC_nCS5*/ MUX_VAL(CP(GPMC_CLK), (IEN | PTD | DIS | M4)); /*GPIO_59*/ @@ -374,6 +393,15 @@ static void cm_t3x_set_common_muxconf(void) MUX_VAL(CP(MMC1_DAT1), (IEN | PTU | EN | M0)); /*MMC1_DAT1*/ MUX_VAL(CP(MMC1_DAT2), (IEN | PTU | EN | M0)); /*MMC1_DAT2*/ MUX_VAL(CP(MMC1_DAT3), (IEN | PTU | EN | M0)); /*MMC1_DAT3*/ + + /* SPI */ + MUX_VAL(CP(MCBSP1_CLKR), (IEN | PTD | DIS | M1)); /*MCSPI4_CLK*/ + MUX_VAL(CP(MCBSP1_DX), (IEN | PTD | DIS | M1)); /*MCSPI4_SIMO*/ + MUX_VAL(CP(MCBSP1_DR), (IEN | PTD | DIS | M1)); /*MCSPI4_SOMI*/ + MUX_VAL(CP(MCBSP1_FSX), (IEN | PTU | EN | M1)); /*MCSPI4_CS0*/ + + /* display controls */ + MUX_VAL(CP(MCBSP1_FSR), (IDIS | PTU | DIS | M4)); /*GPIO_157*/ } static void cm_t35_set_muxconf(void) @@ -428,7 +456,7 @@ void set_muxconf_regs(void) cm_t3730_set_muxconf(); } -#ifdef CONFIG_GENERIC_MMC +#if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD) int board_mmc_getcd(struct mmc *mmc) { u8 val; @@ -470,7 +498,7 @@ static void setup_net_chip_gmpc(void) &ctrl_base->gpmc_nadv_ale); } -#ifdef CONFIG_DRIVER_OMAP34XX_I2C +#ifdef CONFIG_SYS_I2C_OMAP34XX /* * Routine: reset_net_chip * Description: reset the Ethernet controller via TPS65930 GPIO |