summaryrefslogtreecommitdiff
path: root/board/atmel
diff options
context:
space:
mode:
Diffstat (limited to 'board/atmel')
-rw-r--r--board/atmel/at91sam9261ek/at91sam9261ek.c36
-rw-r--r--board/atmel/at91sam9m10g45ek/Makefile55
-rw-r--r--board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c334
-rw-r--r--board/atmel/at91sam9m10g45ek/config.mk1
-rw-r--r--board/atmel/at91sam9m10g45ek/led.c41
5 files changed, 467 insertions, 0 deletions
diff --git a/board/atmel/at91sam9261ek/at91sam9261ek.c b/board/atmel/at91sam9261ek/at91sam9261ek.c
index 0817e60..2f6b599 100644
--- a/board/atmel/at91sam9261ek/at91sam9261ek.c
+++ b/board/atmel/at91sam9261ek/at91sam9261ek.c
@@ -57,6 +57,16 @@ static void at91sam9261ek_nand_hw_init(void)
csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
/* Configure SMC CS3 for NAND/SmartMedia */
+#ifdef CONFIG_AT91SAM9G10EK
+ at91_sys_write(AT91_SMC_SETUP(3),
+ AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) |
+ AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0));
+ at91_sys_write(AT91_SMC_PULSE(3),
+ AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(7) |
+ AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(7));
+ at91_sys_write(AT91_SMC_CYCLE(3),
+ AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7));
+#else
at91_sys_write(AT91_SMC_SETUP(3),
AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) |
AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
@@ -65,6 +75,7 @@ static void at91sam9261ek_nand_hw_init(void)
AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
at91_sys_write(AT91_SMC_CYCLE(3),
AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
+#endif
at91_sys_write(AT91_SMC_MODE(3),
AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
AT91_SMC_EXNWMODE_DISABLE |
@@ -92,6 +103,21 @@ static void at91sam9261ek_nand_hw_init(void)
static void at91sam9261ek_dm9000_hw_init(void)
{
/* Configure SMC CS2 for DM9000 */
+#ifdef CONFIG_AT91SAM9G10EK
+ at91_sys_write(AT91_SMC_SETUP(2),
+ AT91_SMC_NWESETUP_(3) | AT91_SMC_NCS_WRSETUP_(0) |
+ AT91_SMC_NRDSETUP_(3) | AT91_SMC_NCS_RDSETUP_(0));
+ at91_sys_write(AT91_SMC_PULSE(2),
+ AT91_SMC_NWEPULSE_(6) | AT91_SMC_NCS_WRPULSE_(8) |
+ AT91_SMC_NRDPULSE_(6) | AT91_SMC_NCS_RDPULSE_(8));
+ at91_sys_write(AT91_SMC_CYCLE(2),
+ AT91_SMC_NWECYCLE_(20) | AT91_SMC_NRDCYCLE_(20));
+ at91_sys_write(AT91_SMC_MODE(2),
+ AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
+ AT91_SMC_EXNWMODE_DISABLE |
+ AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16 |
+ AT91_SMC_TDF_(1));
+#else
at91_sys_write(AT91_SMC_SETUP(2),
AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) |
AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0));
@@ -105,6 +131,7 @@ static void at91sam9261ek_dm9000_hw_init(void)
AT91_SMC_EXNWMODE_DISABLE |
AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16 |
AT91_SMC_TDF_(1));
+#endif
/* Configure Reset signal as output */
at91_set_gpio_output(AT91_PIN_PC10, 0);
@@ -169,7 +196,11 @@ static void at91sam9261ek_lcd_hw_init(void)
at91_sys_write(AT91_PMC_SCER, AT91_PMC_HCK1);
+#ifdef CONFIG_AT91SAM9G10EK
+ gd->fb_base = CONFIG_AT91SAM9G10_LCD_BASE;
+#else
gd->fb_base = AT91SAM9261_SRAM_BASE;
+#endif
}
#ifdef CONFIG_LCD_INFO
@@ -207,8 +238,13 @@ int board_init(void)
/* Enable Ctrlc */
console_init_f();
+#ifdef CONFIG_AT91SAM9G10EK
+ /* arch number of AT91SAM9G10EK-Board */
+ gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G10EK;
+#else
/* arch number of AT91SAM9261EK-Board */
gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9261EK;
+#endif
/* adress of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
diff --git a/board/atmel/at91sam9m10g45ek/Makefile b/board/atmel/at91sam9m10g45ek/Makefile
new file mode 100644
index 0000000..4caf1e4
--- /dev/null
+++ b/board/atmel/at91sam9m10g45ek/Makefile
@@ -0,0 +1,55 @@
+#
+# (C) Copyright 2003-2008
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# (C) Copyright 2008
+# Stelian Pop <stelian.pop@leadtechdesign.com>
+# Lead Tech Design <www.leadtechdesign.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS-y += at91sam9m10g45ek.o
+COBJS-y += led.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS-y))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
new file mode 100644
index 0000000..45a14a9
--- /dev/null
+++ b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
@@ -0,0 +1,334 @@
+/*
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian.pop@leadtechdesign.com>
+ * Lead Tech Design <www.leadtechdesign.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/sizes.h>
+#include <asm/arch/at91sam9g45.h>
+#include <asm/arch/at91sam9_matrix.h>
+#include <asm/arch/at91sam9_smc.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_rstc.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/io.h>
+#include <asm/arch/hardware.h>
+#include <lcd.h>
+#include <atmel_lcdc.h>
+#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
+#include <net.h>
+#endif
+#include <netdev.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* ------------------------------------------------------------------------- */
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+
+#ifdef CONFIG_CMD_NAND
+static void at91sam9m10g45ek_nand_hw_init(void)
+{
+ unsigned long csa;
+
+ /* Enable CS3 */
+ csa = at91_sys_read(AT91_MATRIX_EBICSA);
+ at91_sys_write(AT91_MATRIX_EBICSA,
+ csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
+
+ /* Configure SMC CS3 for NAND/SmartMedia */
+ at91_sys_write(AT91_SMC_SETUP(3),
+ AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) |
+ AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
+ at91_sys_write(AT91_SMC_PULSE(3),
+ AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(3) |
+ AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(2));
+ at91_sys_write(AT91_SMC_CYCLE(3),
+ AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(4));
+ at91_sys_write(AT91_SMC_MODE(3),
+ AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
+ AT91_SMC_EXNWMODE_DISABLE |
+#ifdef CONFIG_SYS_NAND_DBW_16
+ AT91_SMC_DBW_16 |
+#else /* CONFIG_SYS_NAND_DBW_8 */
+ AT91_SMC_DBW_8 |
+#endif
+ AT91_SMC_TDF_(3));
+
+ at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9G45_ID_PIOC);
+
+ /* Configure RDY/BSY */
+ at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
+
+ /* Enable NandFlash */
+ at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
+}
+#endif
+
+#ifdef CONFIG_MACB
+static void at91sam9m10g45ek_macb_hw_init(void)
+{
+ unsigned long rstc;
+
+ /* Enable clock */
+ at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9G45_ID_EMAC);
+
+ /*
+ * Disable pull-up on:
+ * RXDV (PA15) => PHY normal mode (not Test mode)
+ * ERX0 (PA12) => PHY ADDR0
+ * ERX1 (PA13) => PHY ADDR1 => PHYADDR = 0x0
+ *
+ * PHY has internal pull-down
+ */
+ writel(pin_to_mask(AT91_PIN_PA15) |
+ pin_to_mask(AT91_PIN_PA12) |
+ pin_to_mask(AT91_PIN_PA13),
+ pin_to_controller(AT91_PIN_PA0) + PIO_PUDR);
+
+ rstc = at91_sys_read(AT91_RSTC_MR);
+
+ /* Need to reset PHY -> 500ms reset */
+ at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
+ (AT91_RSTC_ERSTL & (0x0D << 8)) |
+ AT91_RSTC_URSTEN);
+
+ at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST);
+
+ /* Wait for end hardware reset */
+ while (!(at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_NRSTL));
+
+ /* Restore NRST value */
+ at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
+ (rstc) |
+ AT91_RSTC_URSTEN);
+
+ /* Re-enable pull-up */
+ writel(pin_to_mask(AT91_PIN_PA15) |
+ pin_to_mask(AT91_PIN_PA12) |
+ pin_to_mask(AT91_PIN_PA13),
+ pin_to_controller(AT91_PIN_PA0) + PIO_PUER);
+
+ at91_macb_hw_init();
+}
+#endif
+
+#ifdef CONFIG_LCD
+
+vidinfo_t panel_info = {
+ vl_col: 480,
+ vl_row: 272,
+ vl_clk: 9000000,
+ vl_sync: ATMEL_LCDC_INVLINE_NORMAL |
+ ATMEL_LCDC_INVFRAME_NORMAL,
+ vl_bpix: 3,
+ vl_tft: 1,
+ vl_hsync_len: 45,
+ vl_left_margin: 1,
+ vl_right_margin:1,
+ vl_vsync_len: 1,
+ vl_upper_margin:40,
+ vl_lower_margin:1,
+ mmio: AT91SAM9G45_LCDC_BASE,
+};
+
+
+void lcd_enable(void)
+{
+ at91_set_A_periph(AT91_PIN_PE6, 1); /* power up */
+}
+
+void lcd_disable(void)
+{
+ at91_set_A_periph(AT91_PIN_PE6, 0); /* power down */
+}
+
+static void at91sam9m10g45ek_lcd_hw_init(void)
+{
+ at91_set_A_periph(AT91_PIN_PE0, 0); /* LCDDPWR */
+ at91_set_A_periph(AT91_PIN_PE2, 0); /* LCDCC */
+ at91_set_A_periph(AT91_PIN_PE3, 0); /* LCDVSYNC */
+ at91_set_A_periph(AT91_PIN_PE4, 0); /* LCDHSYNC */
+ at91_set_A_periph(AT91_PIN_PE5, 0); /* LCDDOTCK */
+
+ at91_set_A_periph(AT91_PIN_PE7, 0); /* LCDD0 */
+ at91_set_A_periph(AT91_PIN_PE8, 0); /* LCDD1 */
+ at91_set_A_periph(AT91_PIN_PE9, 0); /* LCDD2 */
+ at91_set_A_periph(AT91_PIN_PE10, 0); /* LCDD3 */
+ at91_set_A_periph(AT91_PIN_PE11, 0); /* LCDD4 */
+ at91_set_A_periph(AT91_PIN_PE12, 0); /* LCDD5 */
+ at91_set_A_periph(AT91_PIN_PE13, 0); /* LCDD6 */
+ at91_set_A_periph(AT91_PIN_PE14, 0); /* LCDD7 */
+ at91_set_A_periph(AT91_PIN_PE15, 0); /* LCDD8 */
+ at91_set_A_periph(AT91_PIN_PE16, 0); /* LCDD9 */
+ at91_set_A_periph(AT91_PIN_PE17, 0); /* LCDD10 */
+ at91_set_A_periph(AT91_PIN_PE18, 0); /* LCDD11 */
+ at91_set_A_periph(AT91_PIN_PE19, 0); /* LCDD12 */
+ at91_set_B_periph(AT91_PIN_PE20, 0); /* LCDD13 */
+ at91_set_A_periph(AT91_PIN_PE21, 0); /* LCDD14 */
+ at91_set_A_periph(AT91_PIN_PE22, 0); /* LCDD15 */
+ at91_set_A_periph(AT91_PIN_PE23, 0); /* LCDD16 */
+ at91_set_A_periph(AT91_PIN_PE24, 0); /* LCDD17 */
+ at91_set_A_periph(AT91_PIN_PE25, 0); /* LCDD18 */
+ at91_set_A_periph(AT91_PIN_PE26, 0); /* LCDD19 */
+ at91_set_A_periph(AT91_PIN_PE27, 0); /* LCDD20 */
+ at91_set_B_periph(AT91_PIN_PE28, 0); /* LCDD21 */
+ at91_set_A_periph(AT91_PIN_PE29, 0); /* LCDD22 */
+ at91_set_A_periph(AT91_PIN_PE30, 0); /* LCDD23 */
+
+ at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9G45_ID_LCDC);
+
+ gd->fb_base = CONFIG_AT91SAM9G45_LCD_BASE;
+}
+
+#ifdef CONFIG_LCD_INFO
+#include <nand.h>
+#include <version.h>
+
+void lcd_show_board_info(void)
+{
+ ulong dram_size, nand_size;
+ int i;
+ char temp[32];
+
+ lcd_printf ("%s\n", U_BOOT_VERSION);
+ lcd_printf ("(C) 2008 ATMEL Corp\n");
+ lcd_printf ("at91support@atmel.com\n");
+ lcd_printf ("%s CPU at %s MHz\n",
+ AT91_CPU_NAME,
+ strmhz(temp, get_cpu_clk_rate()));
+
+ dram_size = 0;
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
+ dram_size += gd->bd->bi_dram[i].size;
+ nand_size = 0;
+ for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
+ nand_size += nand_info[i].size;
+ lcd_printf (" %ld MB SDRAM, %ld MB NAND\n",
+ dram_size >> 20,
+ nand_size >> 20 );
+}
+#endif /* CONFIG_LCD_INFO */
+#endif
+
+int board_init(void)
+{
+ /* Enable Ctrlc */
+ console_init_f();
+
+ /* arch number of AT91SAM9M10G45EK-Board */
+#ifdef CONFIG_AT91SAM9M10G45EK
+ gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9M10G45EK;
+#elif defined CONFIG_AT91SAM9G45EKES
+ gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G45EKES;
+#endif
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+ at91_serial_hw_init();
+#ifdef CONFIG_CMD_NAND
+ at91sam9m10g45ek_nand_hw_init();
+#endif
+#ifdef CONFIG_HAS_DATAFLASH
+ at91_spi0_hw_init(1 << 0);
+#endif
+#ifdef CONFIG_ATMEL_SPI
+ at91_spi0_hw_init(1 << 4);
+#endif
+
+#ifdef CONFIG_MACB
+ at91sam9m10g45ek_macb_hw_init();
+#endif
+
+#ifdef CONFIG_LCD
+ at91sam9m10g45ek_lcd_hw_init();
+#endif
+ return 0;
+}
+
+int dram_init(void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+void reset_phy(void)
+{
+#ifdef CONFIG_MACB
+ /*
+ * Initialize ethernet HW addr prior to starting Linux,
+ * needed for nfsroot
+ */
+ eth_init(gd->bd);
+#endif
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+ int rc = 0;
+#ifdef CONFIG_MACB
+ rc = macb_eth_initialize(0, (void *)AT91SAM9G45_BASE_EMAC, 0x00);
+#endif
+ return rc;
+}
+
+/* SPI chip select control */
+#ifdef CONFIG_ATMEL_SPI
+#include <spi.h>
+
+int spi_cs_is_valid(unsigned int bus, unsigned int cs)
+{
+ return bus == 0 && cs < 2;
+}
+
+void spi_cs_activate(struct spi_slave *slave)
+{
+ switch(slave->cs) {
+ case 1:
+ at91_set_gpio_output(AT91_PIN_PB18, 0);
+ break;
+ case 0:
+ default:
+ at91_set_gpio_output(AT91_PIN_PB3, 0);
+ break;
+ }
+}
+
+void spi_cs_deactivate(struct spi_slave *slave)
+{
+ switch(slave->cs) {
+ case 1:
+ at91_set_gpio_output(AT91_PIN_PB18, 1);
+ break;
+ case 0:
+ default:
+ at91_set_gpio_output(AT91_PIN_PB3, 1);
+ break;
+ }
+}
+#endif /* CONFIG_ATMEL_SPI */
diff --git a/board/atmel/at91sam9m10g45ek/config.mk b/board/atmel/at91sam9m10g45ek/config.mk
new file mode 100644
index 0000000..7fe9d03
--- /dev/null
+++ b/board/atmel/at91sam9m10g45ek/config.mk
@@ -0,0 +1 @@
+TEXT_BASE = 0x73f00000
diff --git a/board/atmel/at91sam9m10g45ek/led.c b/board/atmel/at91sam9m10g45ek/led.c
new file mode 100644
index 0000000..ff59a2d
--- /dev/null
+++ b/board/atmel/at91sam9m10g45ek/led.c
@@ -0,0 +1,41 @@
+/*
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian.pop@leadtechdesign.com>
+ * Lead Tech Design <www.leadtechdesign.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/at91sam9g45.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/io.h>
+
+void coloured_LED_init(void)
+{
+ /* Enable clock */
+ at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9G45_ID_PIODE);
+
+ at91_set_gpio_output(CONFIG_RED_LED, 1);
+ at91_set_gpio_output(CONFIG_GREEN_LED, 1);
+
+ at91_set_gpio_value(CONFIG_RED_LED, 0);
+ at91_set_gpio_value(CONFIG_GREEN_LED, 1);
+}
generated by cgit v1.1 at 2024-12-11 11:06:16 +0000