diff options
Diffstat (limited to 'board/amcc')
| -rw-r--r-- | board/amcc/bamboo/bamboo.c | 61 | ||||
| -rw-r--r-- | board/amcc/canyonlands/canyonlands.c | 37 | ||||
| -rw-r--r-- | board/amcc/ebony/ebony.c | 39 | ||||
| -rw-r--r-- | board/amcc/katmai/katmai.c | 40 | ||||
| -rw-r--r-- | board/amcc/luan/luan.c | 40 | ||||
| -rw-r--r-- | board/amcc/ocotea/ocotea.c | 40 | ||||
| -rw-r--r-- | board/amcc/sequoia/sequoia.c | 65 | ||||
| -rw-r--r-- | board/amcc/taishan/taishan.c | 39 | ||||
| -rw-r--r-- | board/amcc/yosemite/yosemite.c | 61 | ||||
| -rw-r--r-- | board/amcc/yucca/yucca.c | 38 |
10 files changed, 1 insertions, 459 deletions
diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c index 313f9f3..3ffdac8 100644 --- a/board/amcc/bamboo/bamboo.c +++ b/board/amcc/bamboo/bamboo.c @@ -522,67 +522,6 @@ int pci_pre_init(struct pci_controller *hose) #endif /* defined(CONFIG_PCI) */ /************************************************************************* - * pci_target_init - * - * The bootstrap configuration provides default settings for the pci - * inbound map (PIM). But the bootstrap config choices are limited and - * may not be sufficient for a given board. - * - ************************************************************************/ -#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) -void pci_target_init(struct pci_controller *hose) -{ - /*--------------------------------------------------------------------------+ - * Set up Direct MMIO registers - *--------------------------------------------------------------------------*/ - /*--------------------------------------------------------------------------+ - | PowerPC440 EP PCI Master configuration. - | Map one 1Gig range of PLB/processor addresses to PCI memory space. - | PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF - | Use byte reversed out routines to handle endianess. - | Make this region non-prefetchable. - +--------------------------------------------------------------------------*/ - out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */ - out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */ - out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */ - out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */ - out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */ - - out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */ - out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */ - out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */ - out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */ - out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */ - - out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */ - out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */ - out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */ - out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */ - - /*--------------------------------------------------------------------------+ - * Set up Configuration registers - *--------------------------------------------------------------------------*/ - - /* Program the board's subsystem id/vendor id */ - pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID, - CONFIG_SYS_PCI_SUBSYS_VENDORID); - pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID); - - /* Configure command register as bus master */ - pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER); - - /* 240nS PCI clock */ - pci_write_config_word(0, PCI_LATENCY_TIMER, 1); - - /* No error reporting */ - pci_write_config_word(0, PCI_ERREN, 0); - - pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101); - -} -#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */ - -/************************************************************************* * pci_master_init * ************************************************************************/ diff --git a/board/amcc/canyonlands/canyonlands.c b/board/amcc/canyonlands/canyonlands.c index 9a8ca8e..13a0dac 100644 --- a/board/amcc/canyonlands/canyonlands.c +++ b/board/amcc/canyonlands/canyonlands.c @@ -326,43 +326,6 @@ phys_size_t initdram(int board_type) } #endif -/* - * pci_target_init - * - * The bootstrap configuration provides default settings for the pci - * inbound map (PIM). But the bootstrap config choices are limited and - * may not be sufficient for a given board. - */ -#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) -void pci_target_init(struct pci_controller * hose ) -{ - /* - * Disable everything - */ - out_le32((void *)PCIL0_PIM0SA, 0); /* disable */ - out_le32((void *)PCIL0_PIM1SA, 0); /* disable */ - out_le32((void *)PCIL0_PIM2SA, 0); /* disable */ - out_le32((void *)PCIL0_EROMBA, 0); /* disable expansion rom */ - - /* - * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 - * strapping options to not support sizes such as 128/256 MB. - */ - out_le32((void *)PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE); - out_le32((void *)PCIL0_PIM0LAH, 0); - out_le32((void *)PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1); - out_le32((void *)PCIL0_BAR0, 0); - - /* - * Program the board's subsystem id/vendor id - */ - out_le16((void *)PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID); - out_le16((void *)PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID); - - out_le16((void *)PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY); -} -#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */ - #if defined(CONFIG_PCI) int board_pcie_first(void) { diff --git a/board/amcc/ebony/ebony.c b/board/amcc/ebony/ebony.c index 1524b53..e4d168f 100644 --- a/board/amcc/ebony/ebony.c +++ b/board/amcc/ebony/ebony.c @@ -195,42 +195,3 @@ int pci_pre_init(struct pci_controller *hose) return 1; } #endif /* defined(CONFIG_PCI) */ - -/************************************************************************* - * pci_target_init - * - * The bootstrap configuration provides default settings for the pci - * inbound map (PIM). But the bootstrap config choices are limited and - * may not be sufficient for a given board. - * - ************************************************************************/ -#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) -void pci_target_init(struct pci_controller *hose) -{ - /*--------------------------------------------------------------------------+ - * Disable everything - *--------------------------------------------------------------------------*/ - out32r(PCIL0_PIM0SA, 0); /* disable */ - out32r(PCIL0_PIM1SA, 0); /* disable */ - out32r(PCIL0_PIM2SA, 0); /* disable */ - out32r(PCIL0_EROMBA, 0); /* disable expansion rom */ - - /*--------------------------------------------------------------------------+ - * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping - * options to not support sizes such as 128/256 MB. - *--------------------------------------------------------------------------*/ - out32r(PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE); - out32r(PCIL0_PIM0LAH, 0); - out32r(PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1); - - out32r(PCIL0_BAR0, 0); - - /*--------------------------------------------------------------------------+ - * Program the board's subsystem id/vendor id - *--------------------------------------------------------------------------*/ - out16r(PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID); - out16r(PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID); - - out16r(PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY); -} -#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */ diff --git a/board/amcc/katmai/katmai.c b/board/amcc/katmai/katmai.c index f43e764..f0b48c0 100644 --- a/board/amcc/katmai/katmai.c +++ b/board/amcc/katmai/katmai.c @@ -1,5 +1,5 @@ /* - * (C) Copyright 2007-2008 + * (C) Copyright 2007-2009 * Stefan Roese, DENX Software Engineering, sr@denx.de. * * See file CREDITS for list of people who contributed to this @@ -291,44 +291,6 @@ int pci_pre_init(struct pci_controller * hose ) } #endif /* defined(CONFIG_PCI) */ -/************************************************************************* - * pci_target_init - * - * The bootstrap configuration provides default settings for the pci - * inbound map (PIM). But the bootstrap config choices are limited and - * may not be sufficient for a given board. - * - ************************************************************************/ -#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) -void pci_target_init(struct pci_controller * hose ) -{ - /*-------------------------------------------------------------------+ - * Disable everything - *-------------------------------------------------------------------*/ - out32r( PCIL0_PIM0SA, 0 ); /* disable */ - out32r( PCIL0_PIM1SA, 0 ); /* disable */ - out32r( PCIL0_PIM2SA, 0 ); /* disable */ - out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */ - - /*-------------------------------------------------------------------+ - * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 - * strapping options to not support sizes such as 128/256 MB. - *-------------------------------------------------------------------*/ - out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE ); - out32r( PCIL0_PIM0LAH, 0 ); - out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 ); - out32r( PCIL0_BAR0, 0 ); - - /*-------------------------------------------------------------------+ - * Program the board's subsystem id/vendor id - *-------------------------------------------------------------------*/ - out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID ); - out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID ); - - out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY ); -} -#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */ - #if defined(CONFIG_PCI) int board_pcie_card_present(int port) { diff --git a/board/amcc/luan/luan.c b/board/amcc/luan/luan.c index 94ba643..e0b297e 100644 --- a/board/amcc/luan/luan.c +++ b/board/amcc/luan/luan.c @@ -160,46 +160,6 @@ int pci_pre_init( struct pci_controller *hose ) /************************************************************************* - * pci_target_init - * - * The bootstrap configuration provides default settings for the pci - * inbound map (PIM). But the bootstrap config choices are limited and - * may not be sufficient for a given board. - * - ************************************************************************/ -#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) -void pci_target_init(struct pci_controller *hose) -{ - /*--------------------------------------------------------------------------+ - * Disable everything - *--------------------------------------------------------------------------*/ - out32r( PCIL0_PIM0SA, 0 ); /* disable */ - out32r( PCIL0_PIM1SA, 0 ); /* disable */ - out32r( PCIL0_PIM2SA, 0 ); /* disable */ - out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */ - - /*--------------------------------------------------------------------------+ - * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping - * options to not support sizes such as 128/256 MB. - *--------------------------------------------------------------------------*/ - out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE ); - out32r( PCIL0_PIM0LAH, 0 ); - out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 ); - - out32r( PCIL0_BAR0, 0 ); - - /*--------------------------------------------------------------------------+ - * Program the board's subsystem id/vendor id - *--------------------------------------------------------------------------*/ - out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID ); - out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID ); - - out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY ); -} -#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */ - - -/************************************************************************* * hw_watchdog_reset * * This routine is called to reset (keep alive) the watchdog timer diff --git a/board/amcc/ocotea/ocotea.c b/board/amcc/ocotea/ocotea.c index 2f64764..b38f3cc 100644 --- a/board/amcc/ocotea/ocotea.c +++ b/board/amcc/ocotea/ocotea.c @@ -307,46 +307,6 @@ int pci_pre_init(struct pci_controller * hose ) } #endif /* defined(CONFIG_PCI) */ -/************************************************************************* - * pci_target_init - * - * The bootstrap configuration provides default settings for the pci - * inbound map (PIM). But the bootstrap config choices are limited and - * may not be sufficient for a given board. - * - ************************************************************************/ -#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) -void pci_target_init(struct pci_controller * hose ) -{ - /*--------------------------------------------------------------------------+ - * Disable everything - *--------------------------------------------------------------------------*/ - out32r( PCIL0_PIM0SA, 0 ); /* disable */ - out32r( PCIL0_PIM1SA, 0 ); /* disable */ - out32r( PCIL0_PIM2SA, 0 ); /* disable */ - out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */ - - /*--------------------------------------------------------------------------+ - * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping - * options to not support sizes such as 128/256 MB. - *--------------------------------------------------------------------------*/ - out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE ); - out32r( PCIL0_PIM0LAH, 0 ); - out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 ); - - out32r( PCIL0_BAR0, 0 ); - - /*--------------------------------------------------------------------------+ - * Program the board's subsystem id/vendor id - *--------------------------------------------------------------------------*/ - out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID ); - out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID ); - - out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY ); -} -#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */ - - void fpga_init(void) { unsigned long group; diff --git a/board/amcc/sequoia/sequoia.c b/board/amcc/sequoia/sequoia.c index 4393820..b8ef4e7 100644 --- a/board/amcc/sequoia/sequoia.c +++ b/board/amcc/sequoia/sequoia.c @@ -427,71 +427,6 @@ int pci_pre_init(struct pci_controller *hose) } #endif /* defined(CONFIG_PCI) */ -/* - * pci_target_init - * - * The bootstrap configuration provides default settings for the pci - * inbound map (PIM). But the bootstrap config choices are limited and - * may not be sufficient for a given board. - */ -#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) -void pci_target_init(struct pci_controller *hose) -{ - /* - * Set up Direct MMIO registers - */ - /* - * PowerPC440EPX PCI Master configuration. - * Map one 1Gig range of PLB/processor addresses to PCI memory space. - * PLB address 0xA0000000-0xDFFFFFFF - * ==> PCI address 0xA0000000-0xDFFFFFFF - * Use byte reversed out routines to handle endianess. - * Make this region non-prefetchable. - */ - out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */ - /* - disabled b4 setting */ - out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */ - out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */ - out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */ - out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, */ - /* and enable region */ - - out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute */ - /* - disabled b4 setting */ - out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */ - out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */ - out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */ - out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, */ - /* and enable region */ - - out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */ - out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */ - out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */ - out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */ - - /* - * Set up Configuration registers - */ - - /* Program the board's subsystem id/vendor id */ - pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID, - CONFIG_SYS_PCI_SUBSYS_VENDORID); - pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID); - - /* Configure command register as bus master */ - pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER); - - /* 240nS PCI clock */ - pci_write_config_word(0, PCI_LATENCY_TIMER, 1); - - /* No error reporting */ - pci_write_config_word(0, PCI_ERREN, 0); - - pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101); - -} -#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */ - #if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) void pci_master_init(struct pci_controller *hose) { diff --git a/board/amcc/taishan/taishan.c b/board/amcc/taishan/taishan.c index 81e8fe1..574ff1a 100644 --- a/board/amcc/taishan/taishan.c +++ b/board/amcc/taishan/taishan.c @@ -240,45 +240,6 @@ int pci_pre_init(struct pci_controller * hose ) } #endif /* defined(CONFIG_PCI) */ -/************************************************************************* - * pci_target_init - * - * The bootstrap configuration provides default settings for the pci - * inbound map (PIM). But the bootstrap config choices are limited and - * may not be sufficient for a given board. - * - ************************************************************************/ -#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) -void pci_target_init(struct pci_controller * hose ) -{ - /*--------------------------------------------------------------------------+ - * Disable everything - *--------------------------------------------------------------------------*/ - out32r( PCIL0_PIM0SA, 0 ); /* disable */ - out32r( PCIL0_PIM1SA, 0 ); /* disable */ - out32r( PCIL0_PIM2SA, 0 ); /* disable */ - out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */ - - /*--------------------------------------------------------------------------+ - * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping - * options to not support sizes such as 128/256 MB. - *--------------------------------------------------------------------------*/ - out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE ); - out32r( PCIL0_PIM0LAH, 0 ); - out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 ); - - out32r( PCIL0_BAR0, 0 ); - - /*--------------------------------------------------------------------------+ - * Program the board's subsystem id/vendor id - *--------------------------------------------------------------------------*/ - out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID ); - out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID ); - - out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY ); -} -#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */ - #ifdef CONFIG_POST /* * Returns 1 if keys pressed to start the power-on long-running tests diff --git a/board/amcc/yosemite/yosemite.c b/board/amcc/yosemite/yosemite.c index e416eeb..cd14a6a 100644 --- a/board/amcc/yosemite/yosemite.c +++ b/board/amcc/yosemite/yosemite.c @@ -408,67 +408,6 @@ int pci_pre_init(struct pci_controller *hose) #endif /* defined(CONFIG_PCI) */ /************************************************************************* - * pci_target_init - * - * The bootstrap configuration provides default settings for the pci - * inbound map (PIM). But the bootstrap config choices are limited and - * may not be sufficient for a given board. - * - ************************************************************************/ -#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) -void pci_target_init(struct pci_controller *hose) -{ - /*--------------------------------------------------------------------------+ - * Set up Direct MMIO registers - *--------------------------------------------------------------------------*/ - /*--------------------------------------------------------------------------+ - | PowerPC440 EP PCI Master configuration. - | Map one 1Gig range of PLB/processor addresses to PCI memory space. - | PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF - | Use byte reversed out routines to handle endianess. - | Make this region non-prefetchable. - +--------------------------------------------------------------------------*/ - out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */ - out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */ - out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */ - out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */ - out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */ - - out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */ - out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */ - out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */ - out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */ - out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */ - - out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */ - out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */ - out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */ - out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */ - - /*--------------------------------------------------------------------------+ - * Set up Configuration registers - *--------------------------------------------------------------------------*/ - - /* Program the board's subsystem id/vendor id */ - pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID, - CONFIG_SYS_PCI_SUBSYS_VENDORID); - pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID); - - /* Configure command register as bus master */ - pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER); - - /* 240nS PCI clock */ - pci_write_config_word(0, PCI_LATENCY_TIMER, 1); - - /* No error reporting */ - pci_write_config_word(0, PCI_ERREN, 0); - - pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101); - -} -#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */ - -/************************************************************************* * pci_master_init * ************************************************************************/ diff --git a/board/amcc/yucca/yucca.c b/board/amcc/yucca/yucca.c index 7315033..0ec26f1 100644 --- a/board/amcc/yucca/yucca.c +++ b/board/amcc/yucca/yucca.c @@ -619,44 +619,6 @@ int pci_pre_init(struct pci_controller * hose ) } #endif /* defined(CONFIG_PCI) */ -/************************************************************************* - * pci_target_init - * - * The bootstrap configuration provides default settings for the pci - * inbound map (PIM). But the bootstrap config choices are limited and - * may not be sufficient for a given board. - * - ************************************************************************/ -#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) -void pci_target_init(struct pci_controller * hose ) -{ - /*-------------------------------------------------------------------+ - * Disable everything - *-------------------------------------------------------------------*/ - out32r( PCIL0_PIM0SA, 0 ); /* disable */ - out32r( PCIL0_PIM1SA, 0 ); /* disable */ - out32r( PCIL0_PIM2SA, 0 ); /* disable */ - out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */ - - /*-------------------------------------------------------------------+ - * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 - * strapping options to not support sizes such as 128/256 MB. - *-------------------------------------------------------------------*/ - out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE ); - out32r( PCIL0_PIM0LAH, 0 ); - out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 ); - out32r( PCIL0_BAR0, 0 ); - - /*-------------------------------------------------------------------+ - * Program the board's subsystem id/vendor id - *-------------------------------------------------------------------*/ - out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID ); - out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID ); - - out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY ); -} -#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */ - #if defined(CONFIG_PCI) int board_pcie_card_present(int port) { |