diff options
Diffstat (limited to 'board/amcc/ebony/ebony.c')
| -rw-r--r-- | board/amcc/ebony/ebony.c | 297 |
1 files changed, 297 insertions, 0 deletions
diff --git a/board/amcc/ebony/ebony.c b/board/amcc/ebony/ebony.c new file mode 100644 index 0000000..f6bb837 --- /dev/null +++ b/board/amcc/ebony/ebony.c @@ -0,0 +1,297 @@ +/* + * Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/processor.h> +#include <spd_sdram.h> + +#define BOOT_SMALL_FLASH 32 /* 00100000 */ +#define FLASH_ONBD_N 2 /* 00000010 */ +#define FLASH_SRAM_SEL 1 /* 00000001 */ + +long int fixed_sdram(void); + +int board_early_init_f(void) +{ + uint reg; + unsigned char *fpga_base = (unsigned char *)CFG_FPGA_BASE; + unsigned char status; + + /*-------------------------------------------------------------------- + * Setup the external bus controller/chip selects + *-------------------------------------------------------------------*/ + mtdcr(ebccfga, xbcfg); + reg = mfdcr(ebccfgd); + mtdcr(ebccfgd, reg | 0x04000000); /* Set ATC */ + + mtebc(pb1ap, 0x02815480); /* NVRAM/RTC */ + mtebc(pb1cr, 0x48018000); /* BA=0x480 1MB R/W 8-bit */ + mtebc(pb7ap, 0x01015280); /* FPGA registers */ + mtebc(pb7cr, 0x48318000); /* BA=0x483 1MB R/W 8-bit */ + + /* read FPGA_REG0 and set the bus controller */ + status = *fpga_base; + if ((status & BOOT_SMALL_FLASH) && !(status & FLASH_ONBD_N)) { + mtebc(pb0ap, 0x9b015480); /* FLASH/SRAM */ + mtebc(pb0cr, 0xfff18000); /* BAS=0xfff 1MB R/W 8-bit */ + mtebc(pb2ap, 0x9b015480); /* 4MB FLASH */ + mtebc(pb2cr, 0xff858000); /* BAS=0xff8 4MB R/W 8-bit */ + } else { + mtebc(pb0ap, 0x9b015480); /* 4MB FLASH */ + mtebc(pb0cr, 0xffc58000); /* BAS=0xffc 4MB R/W 8-bit */ + + /* set CS2 if FLASH_ONBD_N == 0 */ + if (!(status & FLASH_ONBD_N)) { + mtebc(pb2ap, 0x9b015480); /* FLASH/SRAM */ + mtebc(pb2cr, 0xff818000); /* BAS=0xff8 4MB R/W 8-bit */ + } + } + + /*-------------------------------------------------------------------- + * Setup the interrupt controller polarities, triggers, etc. + *-------------------------------------------------------------------*/ + mtdcr(uic0sr, 0xffffffff); /* clear all */ + mtdcr(uic0er, 0x00000000); /* disable all */ + mtdcr(uic0cr, 0x00000009); /* SMI & UIC1 crit are critical */ + mtdcr(uic0pr, 0xfffffe13); /* per ref-board manual */ + mtdcr(uic0tr, 0x01c00008); /* per ref-board manual */ + mtdcr(uic0vr, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr(uic0sr, 0xffffffff); /* clear all */ + + mtdcr(uic1sr, 0xffffffff); /* clear all */ + mtdcr(uic1er, 0x00000000); /* disable all */ + mtdcr(uic1cr, 0x00000000); /* all non-critical */ + mtdcr(uic1pr, 0xffffe0ff); /* per ref-board manual */ + mtdcr(uic1tr, 0x00ffc000); /* per ref-board manual */ + mtdcr(uic1vr, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr(uic1sr, 0xffffffff); /* clear all */ + + return 0; +} + +int checkboard(void) +{ + sys_info_t sysinfo; + unsigned char *s = getenv("serial#"); + + get_sys_info(&sysinfo); + + printf("Board: Ebony - AMCC PPC440GP Evaluation Board"); + if (s != NULL) { + puts(", serial# "); + puts(s); + } + putc('\n'); + + printf("\tVCO: %lu MHz\n", sysinfo.freqVCOMhz / 1000000); + printf("\tCPU: %lu MHz\n", sysinfo.freqProcessor / 1000000); + printf("\tPLB: %lu MHz\n", sysinfo.freqPLB / 1000000); + printf("\tOPB: %lu MHz\n", sysinfo.freqOPB / 1000000); + printf("\tEPB: %lu MHz\n", sysinfo.freqEPB / 1000000); + return (0); +} + +long int initdram(int board_type) +{ + long dram_size = 0; + +#if defined(CONFIG_SPD_EEPROM) + dram_size = spd_sdram(0); +#else + dram_size = fixed_sdram(); +#endif + return dram_size; +} + +#if defined(CFG_DRAM_TEST) +int testdram(void) +{ + uint *pstart = (uint *) 0x00000000; + uint *pend = (uint *) 0x08000000; + uint *p; + + for (p = pstart; p < pend; p++) + *p = 0xaaaaaaaa; + + for (p = pstart; p < pend; p++) { + if (*p != 0xaaaaaaaa) { + printf("SDRAM test fails at: %08x\n", (uint) p); + return 1; + } + } + + for (p = pstart; p < pend; p++) + *p = 0x55555555; + + for (p = pstart; p < pend; p++) { + if (*p != 0x55555555) { + printf("SDRAM test fails at: %08x\n", (uint) p); + return 1; + } + } + return 0; +} +#endif + +#if !defined(CONFIG_SPD_EEPROM) +/************************************************************************* + * fixed sdram init -- doesn't use serial presence detect. + * + * Assumes: 128 MB, non-ECC, non-registered + * PLB @ 133 MHz + * + ************************************************************************/ +long int fixed_sdram(void) +{ + uint reg; + + /*-------------------------------------------------------------------- + * Setup some default + *------------------------------------------------------------------*/ + mtsdram(mem_uabba, 0x00000000); /* ubba=0 (default) */ + mtsdram(mem_slio, 0x00000000); /* rdre=0 wrre=0 rarw=0 */ + mtsdram(mem_devopt, 0x00000000); /* dll=0 ds=0 (normal) */ + mtsdram(mem_wddctr, 0x00000000); /* wrcp=0 dcd=0 */ + mtsdram(mem_clktr, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */ + + /*-------------------------------------------------------------------- + * Setup for board-specific specific mem + *------------------------------------------------------------------*/ + /* + * Following for CAS Latency = 2.5 @ 133 MHz PLB + */ + mtsdram(mem_b0cr, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */ + mtsdram(mem_tr0, 0x410a4012); /* WR=2 WD=1 CL=2.5 PA=3 CP=4 LD=2 */ + /* RA=10 RD=3 */ + mtsdram(mem_tr1, 0x8080082f); /* SS=T2 SL=STAGE 3 CD=1 CT=0x02f */ + mtsdram(mem_rtr, 0x08200000); /* Rate 15.625 ns @ 133 MHz PLB */ + mtsdram(mem_cfg1, 0x00000000); /* Self-refresh exit, disable PM */ + udelay(400); /* Delay 200 usecs (min) */ + + /*-------------------------------------------------------------------- + * Enable the controller, then wait for DCEN to complete + *------------------------------------------------------------------*/ + mtsdram(mem_cfg0, 0x86000000); /* DCEN=1, PMUD=1, 64-bit */ + for (;;) { + mfsdram(mem_mcsts, reg); + if (reg & 0x80000000) + break; + } + + return (128 * 1024 * 1024); /* 128 MB */ +} +#endif /* !defined(CONFIG_SPD_EEPROM) */ + +/************************************************************************* + * pci_pre_init + * + * This routine is called just prior to registering the hose and gives + * the board the opportunity to check things. Returning a value of zero + * indicates that things are bad & PCI initialization should be aborted. + * + * Different boards may wish to customize the pci controller structure + * (add regions, override default access routines, etc) or perform + * certain pre-initialization actions. + * + ************************************************************************/ +#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) +int pci_pre_init(struct pci_controller *hose) +{ + unsigned long strap; + + /*--------------------------------------------------------------------------+ + * The ebony board is always configured as the host & requires the + * PCI arbiter to be enabled. + *--------------------------------------------------------------------------*/ + strap = mfdcr(cpc0_strp1); + if ((strap & 0x00100000) == 0) { + printf("PCI: CPC0_STRP1[PAE] not set.\n"); + return 0; + } + + return 1; +} +#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */ + +/************************************************************************* + * pci_target_init + * + * The bootstrap configuration provides default settings for the pci + * inbound map (PIM). But the bootstrap config choices are limited and + * may not be sufficient for a given board. + * + ************************************************************************/ +#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) +void pci_target_init(struct pci_controller *hose) +{ + DECLARE_GLOBAL_DATA_PTR; + + /*--------------------------------------------------------------------------+ + * Disable everything + *--------------------------------------------------------------------------*/ + out32r(PCIX0_PIM0SA, 0); /* disable */ + out32r(PCIX0_PIM1SA, 0); /* disable */ + out32r(PCIX0_PIM2SA, 0); /* disable */ + out32r(PCIX0_EROMBA, 0); /* disable expansion rom */ + + /*--------------------------------------------------------------------------+ + * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping + * options to not support sizes such as 128/256 MB. + *--------------------------------------------------------------------------*/ + out32r(PCIX0_PIM0LAL, CFG_SDRAM_BASE); + out32r(PCIX0_PIM0LAH, 0); + out32r(PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1); + + out32r(PCIX0_BAR0, 0); + + /*--------------------------------------------------------------------------+ + * Program the board's subsystem id/vendor id + *--------------------------------------------------------------------------*/ + out16r(PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID); + out16r(PCIX0_SBSYSID, CFG_PCI_SUBSYS_DEVICEID); + + out16r(PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY); +} +#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */ + +/************************************************************************* + * is_pci_host + * + * This routine is called to determine if a pci scan should be + * performed. With various hardware environments (especially cPCI and + * PPMC) it's insufficient to depend on the state of the arbiter enable + * bit in the strap register, or generic host/adapter assumptions. + * + * Rather than hard-code a bad assumption in the general 440 code, the + * 440 pci code requires the board to decide at runtime. + * + * Return 0 for adapter mode, non-zero for host (monarch) mode. + * + * + ************************************************************************/ +#if defined(CONFIG_PCI) +int is_pci_host(struct pci_controller *hose) +{ + /* The ebony board is always configured as host. */ + return (1); +} +#endif /* defined(CONFIG_PCI) */ |