diff options
Diffstat (limited to 'arch')
49 files changed, 2490 insertions, 126 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 397981a..4a62d4b 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -840,15 +840,12 @@ config STM32 config ARCH_ROCKCHIP bool "Support Rockchip SoCs" - select SUPPORT_SPL - select SPL select OF_CONTROL - select CPU_V7 select BLK select DM - select SPL_DM + select SPL_DM if SPL select SYS_MALLOC_F - select SPL_SYS_MALLOC_SIMPLE + select SPL_SYS_MALLOC_SIMPLE if SPL select DM_GPIO select DM_I2C select DM_MMC diff --git a/arch/arm/cpu/armv7/am33xx/ddr.c b/arch/arm/cpu/armv7/am33xx/ddr.c index 888cf1f..6acf30c 100644 --- a/arch/arm/cpu/armv7/am33xx/ddr.c +++ b/arch/arm/cpu/armv7/am33xx/ddr.c @@ -120,12 +120,15 @@ void config_sdram_emif4d5(const struct emif_regs *regs, int nr) writel(regs->sdram_config, &emif_reg[nr]->emif_sdram_config); writel(regs->sdram_config, &cstat->secure_emif_sdram_config); + + /* Wait 1ms because of L3 timeout error */ + udelay(1000); + writel(regs->ref_ctrl, &emif_reg[nr]->emif_sdram_ref_ctrl); writel(regs->ref_ctrl, &emif_reg[nr]->emif_sdram_ref_ctrl_shdw); /* Perform hardware leveling for DDR3 */ if (emif_sdram_type(regs->sdram_config) == EMIF_SDRAM_TYPE_DDR3) { - udelay(1000); writel(readl(&emif_reg[nr]->emif_ddr_ext_phy_ctrl_36) | 0x100, &emif_reg[nr]->emif_ddr_ext_phy_ctrl_36); writel(readl(&emif_reg[nr]->emif_ddr_ext_phy_ctrl_36_shdw) | @@ -289,19 +292,14 @@ static void ext_phy_settings_hwlvl(const struct emif_regs *regs, int nr) void config_ddr_phy(const struct emif_regs *regs, int nr) { /* - * Disable initialization and refreshes for now until we - * finish programming EMIF regs. - * Also set time between rising edge of DDR_RESET to rising - * edge of DDR_CKE to > 500us per memory spec. + * Disable initialization and refreshes for now until we finish + * programming EMIF regs and set time between rising edge of + * DDR_RESET to rising edge of DDR_CKE to > 500us per memory spec. + * We currently hardcode a value based on a max expected frequency + * of 400MHz. */ -#ifndef CONFIG_AM43XX - setbits_le32(&emif_reg[nr]->emif_sdram_ref_ctrl, - EMIF_REG_INITREF_DIS_MASK); -#endif - if (regs->zq_config) - /* Set time between rising edge of DDR_RESET to rising - * edge of DDR_CKE to > 500us per memory spec. */ - writel(0x00003100, &emif_reg[nr]->emif_sdram_ref_ctrl); + writel(EMIF_REG_INITREF_DIS_MASK | 0x3100, + &emif_reg[nr]->emif_sdram_ref_ctrl); writel(regs->emif_ddr_phy_ctlr_1, &emif_reg[nr]->emif_ddr_phy_ctrl_1); diff --git a/arch/arm/cpu/armv7/ls102xa/psci.S b/arch/arm/cpu/armv7/ls102xa/psci.S index f9b26b4..8f38680 100644 --- a/arch/arm/cpu/armv7/ls102xa/psci.S +++ b/arch/arm/cpu/armv7/ls102xa/psci.S @@ -12,19 +12,102 @@ #include <asm/arch-armv7/generictimer.h> #include <asm/psci.h> +#define RCPM_TWAITSR 0x04C + #define SCFG_CORE0_SFT_RST 0x130 #define SCFG_CORESRENCR 0x204 -#define DCFG_CCSR_BRR 0x0E4 -#define DCFG_CCSR_SCRATCHRW1 0x200 +#define DCFG_CCSR_RSTCR 0x0B0 +#define DCFG_CCSR_RSTCR_RESET_REQ 0x2 +#define DCFG_CCSR_BRR 0x0E4 +#define DCFG_CCSR_SCRATCHRW1 0x200 + +#define PSCI_FN_PSCI_VERSION_FEATURE_MASK 0x0 +#define PSCI_FN_CPU_SUSPEND_FEATURE_MASK 0x0 +#define PSCI_FN_CPU_OFF_FEATURE_MASK 0x0 +#define PSCI_FN_CPU_ON_FEATURE_MASK 0x0 +#define PSCI_FN_AFFINITY_INFO_FEATURE_MASK 0x0 +#define PSCI_FN_SYSTEM_OFF_FEATURE_MASK 0x0 +#define PSCI_FN_SYSTEM_RESET_FEATURE_MASK 0x0 .pushsection ._secure.text, "ax" .arch_extension sec + .align 5 + #define ONE_MS (GENERIC_TIMER_CLK / 1000) #define RESET_WAIT (30 * ONE_MS) +.globl psci_version +psci_version: + movw r0, #0 + movt r0, #1 + + bx lr + +_ls102x_psci_supported_table: + .word ARM_PSCI_0_2_FN_PSCI_VERSION + .word PSCI_FN_PSCI_VERSION_FEATURE_MASK + .word ARM_PSCI_0_2_FN_CPU_SUSPEND + .word PSCI_FN_CPU_SUSPEND_FEATURE_MASK + .word ARM_PSCI_0_2_FN_CPU_OFF + .word PSCI_FN_CPU_OFF_FEATURE_MASK + .word ARM_PSCI_0_2_FN_CPU_ON + .word PSCI_FN_CPU_ON_FEATURE_MASK + .word ARM_PSCI_0_2_FN_AFFINITY_INFO + .word PSCI_FN_AFFINITY_INFO_FEATURE_MASK + .word ARM_PSCI_0_2_FN_SYSTEM_OFF + .word PSCI_FN_SYSTEM_OFF_FEATURE_MASK + .word ARM_PSCI_0_2_FN_SYSTEM_RESET + .word PSCI_FN_SYSTEM_RESET_FEATURE_MASK + .word 0 + .word ARM_PSCI_RET_NI + +.globl psci_features +psci_features: + adr r2, _ls102x_psci_supported_table +1: ldr r3, [r2] + cmp r3, #0 + beq out_psci_features + cmp r1, r3 + addne r2, r2, #8 + bne 1b + +out_psci_features: + ldr r0, [r2, #4] + bx lr + +@ r0: return value ARM_PSCI_RET_SUCCESS or ARM_PSCI_RET_INVAL +@ r1: input target CPU ID in MPIDR format, original value in r1 may be dropped +@ r4: output validated CPU ID if ARM_PSCI_RET_SUCCESS returns, meaningless for +@ ARM_PSCI_RET_INVAL,suppose caller saves r4 before calling +LENTRY(psci_check_target_cpu_id) + @ Get the real CPU number + and r4, r1, #0xff + mov r0, #ARM_PSCI_RET_INVAL + + @ Bit[31:24], bits must be zero. + tst r1, #0xff000000 + bxne lr + + @ Affinity level 2 - Cluster: only one cluster in LS1021xa. + tst r1, #0xff0000 + bxne lr + + @ Affinity level 1 - Processors: should be in 0xf00 format. + lsr r1, r1, #8 + teq r1, #0xf + bxne lr + + @ Affinity level 0 - CPU: only 0, 1 are valid in LS1021xa. + cmp r4, #2 + bxge lr + + mov r0, #ARM_PSCI_RET_SUCCESS + bx lr +ENDPROC(psci_check_target_cpu_id) + @ r1 = target CPU @ r2 = target PC .globl psci_cpu_on @@ -33,7 +116,9 @@ psci_cpu_on: @ Clear and Get the correct CPU number @ r1 = 0xf01 - and r4, r1, #0xff + bl psci_check_target_cpu_id + cmp r0, #ARM_PSCI_RET_INVAL + beq out_psci_cpu_on mov r0, r4 mov r1, r2 @@ -101,6 +186,7 @@ holdoff_release: @ Return mov r0, #ARM_PSCI_RET_SUCCESS +out_psci_cpu_on: pop {r4, r5, r6, lr} bx lr @@ -111,4 +197,50 @@ psci_cpu_off: 1: wfi b 1b +.globl psci_affinity_info +psci_affinity_info: + push {lr} + + mov r0, #ARM_PSCI_RET_INVAL + + @ Verify Affinity level + cmp r2, #0 + bne out_affinity_info + + bl psci_check_target_cpu_id + cmp r0, #ARM_PSCI_RET_INVAL + beq out_affinity_info + mov r1, r4 + + @ Get RCPM base address + movw r4, #(CONFIG_SYS_FSL_RCPM_ADDR & 0xffff) + movt r4, #(CONFIG_SYS_FSL_RCPM_ADDR >> 16) + + mov r0, #PSCI_AFFINITY_LEVEL_ON + + @ Detect target CPU state + ldr r2, [r4, #RCPM_TWAITSR] + rev r2, r2 + lsr r2, r2, r1 + ands r2, r2, #1 + beq out_affinity_info + + mov r0, #PSCI_AFFINITY_LEVEL_OFF + +out_affinity_info: + pop {pc} + +.globl psci_system_reset +psci_system_reset: + @ Get DCFG base address + movw r1, #(CONFIG_SYS_FSL_GUTS_ADDR & 0xffff) + movt r1, #(CONFIG_SYS_FSL_GUTS_ADDR >> 16) + + mov r2, #DCFG_CCSR_RSTCR_RESET_REQ + rev r2, r2 + str r2, [r1, #DCFG_CCSR_RSTCR] + +1: wfi + b 1b + .popsection diff --git a/arch/arm/cpu/armv7/psci.S b/arch/arm/cpu/armv7/psci.S index 350b75c..f80f6e2 100644 --- a/arch/arm/cpu/armv7/psci.S +++ b/arch/arm/cpu/armv7/psci.S @@ -46,20 +46,62 @@ ENTRY(default_psci_vector) ENDPROC(default_psci_vector) .weak default_psci_vector +ENTRY(psci_version) ENTRY(psci_cpu_suspend) ENTRY(psci_cpu_off) ENTRY(psci_cpu_on) +ENTRY(psci_affinity_info) ENTRY(psci_migrate) +ENTRY(psci_migrate_info_type) +ENTRY(psci_migrate_info_up_cpu) +ENTRY(psci_system_off) +ENTRY(psci_system_reset) +ENTRY(psci_features) +ENTRY(psci_cpu_freeze) +ENTRY(psci_cpu_default_suspend) +ENTRY(psci_node_hw_state) +ENTRY(psci_system_suspend) +ENTRY(psci_set_suspend_mode) +ENTRY(psi_stat_residency) +ENTRY(psci_stat_count) mov r0, #ARM_PSCI_RET_NI @ Return -1 (Not Implemented) mov pc, lr +ENDPROC(psci_stat_count) +ENDPROC(psi_stat_residency) +ENDPROC(psci_set_suspend_mode) +ENDPROC(psci_system_suspend) +ENDPROC(psci_node_hw_state) +ENDPROC(psci_cpu_default_suspend) +ENDPROC(psci_cpu_freeze) +ENDPROC(psci_features) +ENDPROC(psci_system_reset) +ENDPROC(psci_system_off) +ENDPROC(psci_migrate_info_up_cpu) +ENDPROC(psci_migrate_info_type) ENDPROC(psci_migrate) +ENDPROC(psci_affinity_info) ENDPROC(psci_cpu_on) ENDPROC(psci_cpu_off) ENDPROC(psci_cpu_suspend) +ENDPROC(psci_version) +.weak psci_version .weak psci_cpu_suspend .weak psci_cpu_off .weak psci_cpu_on +.weak psci_affinity_info .weak psci_migrate +.weak psci_migrate_info_type +.weak psci_migrate_info_up_cpu +.weak psci_system_off +.weak psci_system_reset +.weak psci_features +.weak psci_cpu_freeze +.weak psci_cpu_default_suspend +.weak psci_node_hw_state +.weak psci_system_suspend +.weak psci_set_suspend_mode +.weak psi_stat_residency +.weak psci_stat_count _psci_table: .word ARM_PSCI_FN_CPU_SUSPEND @@ -70,6 +112,42 @@ _psci_table: .word psci_cpu_on .word ARM_PSCI_FN_MIGRATE .word psci_migrate + .word ARM_PSCI_0_2_FN_PSCI_VERSION + .word psci_version + .word ARM_PSCI_0_2_FN_CPU_SUSPEND + .word psci_cpu_suspend + .word ARM_PSCI_0_2_FN_CPU_OFF + .word psci_cpu_off + .word ARM_PSCI_0_2_FN_CPU_ON + .word psci_cpu_on + .word ARM_PSCI_0_2_FN_AFFINITY_INFO + .word psci_affinity_info + .word ARM_PSCI_0_2_FN_MIGRATE + .word psci_migrate + .word ARM_PSCI_0_2_FN_MIGRATE_INFO_TYPE + .word psci_migrate_info_type + .word ARM_PSCI_0_2_FN_MIGRATE_INFO_UP_CPU + .word psci_migrate_info_up_cpu + .word ARM_PSCI_0_2_FN_SYSTEM_OFF + .word psci_system_off + .word ARM_PSCI_0_2_FN_SYSTEM_RESET + .word psci_system_reset + .word ARM_PSCI_1_0_FN_PSCI_FEATURES + .word psci_features + .word ARM_PSCI_1_0_FN_CPU_FREEZE + .word psci_cpu_freeze + .word ARM_PSCI_1_0_FN_CPU_DEFAULT_SUSPEND + .word psci_cpu_default_suspend + .word ARM_PSCI_1_0_FN_NODE_HW_STATE + .word psci_node_hw_state + .word ARM_PSCI_1_0_FN_SYSTEM_SUSPEND + .word psci_system_suspend + .word ARM_PSCI_1_0_FN_SET_SUSPEND_MODE + .word psci_set_suspend_mode + .word ARM_PSCI_1_0_FN_STAT_RESIDENCY + .word psi_stat_residency + .word ARM_PSCI_1_0_FN_STAT_COUNT + .word psci_stat_count .word 0 .word 0 diff --git a/arch/arm/cpu/armv8/fsl-layerscape/Makefile b/arch/arm/cpu/armv8/fsl-layerscape/Makefile index bcf6b48..8c1317f 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/Makefile +++ b/arch/arm/cpu/armv8/fsl-layerscape/Makefile @@ -33,3 +33,7 @@ endif ifneq ($(CONFIG_LS1012A),) obj-$(CONFIG_SYS_HAS_SERDES) += ls1012a_serdes.o endif + +ifneq ($(CONFIG_LS1046A),) +obj-$(CONFIG_SYS_HAS_SERDES) += ls1046a_serdes.o +endif diff --git a/arch/arm/cpu/armv8/fsl-layerscape/cpu.c b/arch/arm/cpu/armv8/fsl-layerscape/cpu.c index 7a2ec6b..e12b773 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/cpu.c +++ b/arch/arm/cpu/armv8/fsl-layerscape/cpu.c @@ -145,11 +145,14 @@ static inline void final_mmu_setup(void) set_ttbr_tcr_mair(el, gd->arch.tlb_addr, get_tcr(el, NULL, NULL), MEMORY_ATTRIBUTES); /* - * MMU is already enabled, just need to invalidate TLB to load the + * EL3 MMU is already enabled, just need to invalidate TLB to load the * new table. The new table is compatible with the current table, if * MMU somehow walks through the new table before invalidation TLB, * it still works. So we don't need to turn off MMU here. + * When EL2 MMU table is created by calling this function, MMU needs + * to be enabled. */ + set_sctlr(get_sctlr() | CR_M); } u64 get_page_table_size(void) @@ -309,7 +312,8 @@ int print_cpuinfo(void) printf("CPU%d(%s):%-4s MHz ", core, type == TY_ITYP_VER_A7 ? "A7 " : (type == TY_ITYP_VER_A53 ? "A53" : - (type == TY_ITYP_VER_A57 ? "A57" : " ")), + (type == TY_ITYP_VER_A57 ? "A57" : + (type == TY_ITYP_VER_A72 ? "A72" : " "))), strmhz(buf, sysinfo.freq_processor[core])); } printf("\n Bus: %-4s MHz ", diff --git a/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc b/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc index 8eee016..f7b949a 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc +++ b/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc @@ -3,6 +3,7 @@ SoC overview 1. LS1043A 2. LS2080A 3. LS1012A + 4. LS1046A LS1043A --------- @@ -127,3 +128,44 @@ The LS1012A SoC includes the following function and features: - Two WatchDog timers - ARM generic timer - QorIQ platform's trust architecture 2.1 + +LS1046A +-------- +The LS1046A integrated multicore processor combines four ARM Cortex-A72 +processor cores with datapath acceleration optimized for L2/3 packet +processing, single pass security offload and robust traffic management +and quality of service. + +The LS1046A SoC includes the following function and features: + - Four 64-bit ARM Cortex-A72 CPUs + - 2 MB unified L2 Cache + - One 64-bit DDR4 SDRAM memory controllers with ECC and interleaving + support + - Data Path Acceleration Architecture (DPAA) incorporating acceleration the + the following functions: + - Packet parsing, classification, and distribution (FMan) + - Queue management for scheduling, packet sequencing, and congestion + management (QMan) + - Hardware buffer management for buffer allocation and de-allocation (BMan) + - Cryptography acceleration (SEC) + - Two Configurable x4 SerDes + - Two PLLs per four-lane SerDes + - Support for 10G operation + - Ethernet interfaces by FMan + - Up to 2 x XFI supporting 10G interface (MAC 9, 10) + - Up to 1 x QSGMII (MAC 5, 6, 10, 1) + - Up to 4 x SGMII supporting 1000Mbps (MAC 5, 6, 9, 10) + - Up to 3 x SGMII supporting 2500Mbps (MAC 5, 9, 10) + - Up to 2 x RGMII supporting 1000Mbps (MAC 3, 4) + - High-speed peripheral interfaces + - Three PCIe 3.0 controllers, one supporting x4 operation + - One serial ATA (SATA 3.0) controllers + - Additional peripheral interfaces + - Three high-speed USB 3.0 controllers with integrated PHY + - Enhanced secure digital host controller (eSDXC/eMMC) + - Quad Serial Peripheral Interface (QSPI) Controller + - Serial peripheral interface (SPI) controller + - Four I2C controllers + - Two DUARTs + - Integrated flash controller (IFC) supporting NAND and NOR flash + - QorIQ platform's trust architecture 2.1 diff --git a/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_serdes.c b/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_serdes.c index fe3444a..f73092a 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_serdes.c +++ b/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_serdes.c @@ -13,6 +13,9 @@ #ifdef CONFIG_SYS_FSL_SRDS_1 static u8 serdes1_prtcl_map[SERDES_PRCTL_COUNT]; #endif +#ifdef CONFIG_SYS_FSL_SRDS_2 +static u8 serdes2_prtcl_map[SERDES_PRCTL_COUNT]; +#endif int is_serdes_configured(enum srds_prtcl device) { @@ -21,6 +24,9 @@ int is_serdes_configured(enum srds_prtcl device) #ifdef CONFIG_SYS_FSL_SRDS_1 ret |= serdes1_prtcl_map[device]; #endif +#ifdef CONFIG_SYS_FSL_SRDS_2 + ret |= serdes2_prtcl_map[device]; +#endif return !!ret; } @@ -38,6 +44,12 @@ int serdes_get_first_lane(u32 sd, enum srds_prtcl device) cfg >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT; break; #endif +#ifdef CONFIG_SYS_FSL_SRDS_2 + case FSL_SRDS_2: + cfg &= FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_MASK; + cfg >>= FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_SHIFT; + break; +#endif default: printf("invalid SerDes%d\n", sd); break; @@ -114,4 +126,11 @@ void fsl_serdes_init(void) FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT, serdes1_prtcl_map); #endif +#ifdef CONFIG_SYS_FSL_SRDS_2 + serdes_init(FSL_SRDS_2, + CONFIG_SYS_FSL_SERDES_ADDR, + FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_MASK, + FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_SHIFT, + serdes2_prtcl_map); +#endif } diff --git a/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_speed.c b/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_speed.c index d0dc58d..8922197 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_speed.c +++ b/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_speed.c @@ -107,6 +107,12 @@ void get_sys_info(struct sys_info *sys_info) case 3: sys_info->freq_fman[0] = freq_c_pll[0] / 3; break; + case 4: + sys_info->freq_fman[0] = freq_c_pll[0] / 4; + break; + case 5: + sys_info->freq_fman[0] = sys_info->freq_systembus; + break; case 6: sys_info->freq_fman[0] = freq_c_pll[1] / 2; break; @@ -124,8 +130,23 @@ void get_sys_info(struct sys_info *sys_info) #ifdef CONFIG_FSL_ESDHC #ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK rcw_tmp = in_be32(&gur->rcwsr[15]); - rcw_tmp = (rcw_tmp & HWA_CGA_M2_CLK_SEL) >> HWA_CGA_M2_CLK_SHIFT; - sys_info->freq_sdhc = freq_c_pll[1] / rcw_tmp; + switch ((rcw_tmp & HWA_CGA_M2_CLK_SEL) >> HWA_CGA_M2_CLK_SHIFT) { + case 1: + sys_info->freq_sdhc = freq_c_pll[1]; + break; + case 2: + sys_info->freq_sdhc = freq_c_pll[1] / 2; + break; + case 3: + sys_info->freq_sdhc = freq_c_pll[1] / 3; + break; + case 6: + sys_info->freq_sdhc = freq_c_pll[0] / 2; + break; + default: + printf("Error: Unknown ESDHC clock select!\n"); + break; + } #else sys_info->freq_sdhc = sys_info->freq_systembus; #endif diff --git a/arch/arm/cpu/armv8/fsl-layerscape/ls1046a_serdes.c b/arch/arm/cpu/armv8/fsl-layerscape/ls1046a_serdes.c new file mode 100644 index 0000000..1da6b71 --- /dev/null +++ b/arch/arm/cpu/armv8/fsl-layerscape/ls1046a_serdes.c @@ -0,0 +1,99 @@ +/* + * Copyright 2016 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/arch/fsl_serdes.h> +#include <asm/arch/immap_lsch2.h> + +struct serdes_config { + u32 protocol; + u8 lanes[SRDS_MAX_LANES]; +}; + +static struct serdes_config serdes1_cfg_tbl[] = { + /* SerDes 1 */ + {0x3333, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC5, + SGMII_FM1_DTSEC6} }, + {0x1133, {XFI_FM1_MAC9, XFI_FM1_MAC10, SGMII_FM1_DTSEC5, + SGMII_FM1_DTSEC6} }, + {0x1333, {XFI_FM1_MAC9, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC5, + SGMII_FM1_DTSEC6} }, + {0x2333, {SGMII_2500_FM1_DTSEC9, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC5, + SGMII_FM1_DTSEC6} }, + {0x2233, {SGMII_2500_FM1_DTSEC9, SGMII_2500_FM1_DTSEC10, + SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0x1040, {XFI_FM1_MAC9, NONE, QSGMII_FM1_A, NONE} }, + {0x2040, {SGMII_2500_FM1_DTSEC9, NONE, QSGMII_FM1_A, NONE} }, + {0x1163, {XFI_FM1_MAC9, XFI_FM1_MAC10, PCIE1, SGMII_FM1_DTSEC6} }, + {0x2263, {SGMII_2500_FM1_DTSEC9, SGMII_2500_FM1_DTSEC10, PCIE1, + SGMII_FM1_DTSEC6} }, + {0x3363, {SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6, PCIE1, + SGMII_FM1_DTSEC6} }, + {0x2223, {SGMII_2500_FM1_DTSEC9, SGMII_2500_FM1_DTSEC10, + SGMII_2500_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {} +}; + +static struct serdes_config serdes2_cfg_tbl[] = { + /* SerDes 2 */ + {0x8888, {PCIE1, PCIE1, PCIE1, PCIE1} }, + {0x5559, {PCIE1, PCIE2, PCIE3, SATA1} }, + {0x5577, {PCIE1, PCIE2, PCIE3, PCIE3} }, + {0x5506, {PCIE1, PCIE2, NONE, PCIE3} }, + {0x0506, {NONE, PCIE2, NONE, PCIE3} }, + {0x0559, {NONE, PCIE2, PCIE3, SATA1} }, + {0x5A59, {PCIE1, SGMII_FM1_DTSEC2, PCIE3, SATA1} }, + {0x5A06, {PCIE1, SGMII_FM1_DTSEC2, NONE, PCIE3} }, + {} +}; + +static struct serdes_config *serdes_cfg_tbl[] = { + serdes1_cfg_tbl, + serdes2_cfg_tbl, +}; + +enum srds_prtcl serdes_get_prtcl(int serdes, int cfg, int lane) +{ + struct serdes_config *ptr; + + if (serdes >= ARRAY_SIZE(serdes_cfg_tbl)) + return 0; + + ptr = serdes_cfg_tbl[serdes]; + while (ptr->protocol) { + if (ptr->protocol == cfg) + return ptr->lanes[lane]; + ptr++; + } + + return 0; +} + +int is_serdes_prtcl_valid(int serdes, u32 prtcl) +{ + int i; + struct serdes_config *ptr; + + if (serdes >= ARRAY_SIZE(serdes_cfg_tbl)) + return 0; + + ptr = serdes_cfg_tbl[serdes]; + while (ptr->protocol) { + if (ptr->protocol == prtcl) + break; + ptr++; + } + + if (!ptr->protocol) + return 0; + + for (i = 0; i < SRDS_MAX_LANES; i++) { + if (ptr->lanes[i] != NONE) + return 1; + } + + return 0; +} diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index ca8712a..c97e3f6 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -31,7 +31,9 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \ rk3288-firefly.dtb \ rk3288-jerry.dtb \ rk3288-rock2-square.dtb \ - rk3036-sdk.dtb + rk3288-evb.dtb \ + rk3036-sdk.dtb \ + rk3399-evb.dtb dtb-$(CONFIG_ARCH_MESON) += \ meson-gxbb-odroidc2.dtb dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \ diff --git a/arch/arm/dts/rk3288-evb.dts b/arch/arm/dts/rk3288-evb.dts new file mode 100644 index 0000000..caf24ee --- /dev/null +++ b/arch/arm/dts/rk3288-evb.dts @@ -0,0 +1,59 @@ +/* + * (C) Copyright 2016 Rockchip Electronics Co., Ltd + * + * SPDX-License-Identifier: GPL-2.0+ X11 + */ + +/dts-v1/; +#include "rk3288-evb.dtsi" + +/ { + model = "Evb-RK3288"; + compatible = "evb-rk3288,evb-rk3288", "rockchip,rk3288"; + + chosen { + stdout-path = &uart2; + }; +}; + +&dmc { + rockchip,num-channels = <2>; + rockchip,pctl-timing = <0x215 0xc8 0x0 0x35 0x26 0x2 0x70 0x2000d + 0x6 0x0 0x8 0x4 0x17 0x24 0xd 0x6 + 0x4 0x8 0x4 0x76 0x4 0x0 0x30 0x0 + 0x1 0x2 0x2 0x4 0x0 0x0 0xc0 0x4 + 0x8 0x1f4>; + rockchip,phy-timing = <0x48d7dd93 0x187008d8 0x121076 + 0x0 0xc3 0x6 0x2>; + rockchip,sdram-channel = /bits/ 8 <0x2 0xa 0x3 0x2 0x2 0x0 0xe 0xe>; + rockchip,sdram-params = <0x20d266a4 0x5b6 2 533000000 6 9 0>; +}; + +&pinctrl { + u-boot,dm-pre-reloc; +}; + +&pwm1 { + status = "okay"; +}; + +&uart2 { + u-boot,dm-pre-reloc; + reg-shift = <2>; +}; + +&sdmmc { + u-boot,dm-pre-reloc; +}; + +&emmc { + u-boot,dm-pre-reloc; +}; + +&gpio3 { + u-boot,dm-pre-reloc; +}; + +&gpio8 { + u-boot,dm-pre-reloc; +}; diff --git a/arch/arm/dts/rk3288-evb.dtsi b/arch/arm/dts/rk3288-evb.dtsi new file mode 100644 index 0000000..cb7d03e --- /dev/null +++ b/arch/arm/dts/rk3288-evb.dtsi @@ -0,0 +1,379 @@ +/* + * (C) Copyright 2016 Rockchip Electronics Co., Ltd + * + * SPDX-License-Identifier: GPL-2.0+ X11 + */ + +#include "rk3288.dtsi" + +/ { + memory { + reg = <0 0x80000000>; + }; + + keys: gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + button@0 { + gpio-key,wakeup = <1>; + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>; + label = "GPIO Power"; + linux,code = <116>; + pinctrl-names = "default"; + pinctrl-0 = <&pwr_key>; + }; + }; + + vcc_sys: vsys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_sys"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vcc_flash: flash-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_flash"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_io>; + }; + + vcc_5v: usb-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc_sys>; + }; + + vcc_host_5v: usb-host-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&host_vbus_drv>; + regulator-name = "vcc_host_5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + vin-supply = <&vcc_5v>; + }; + + vcc_otg_5v: usb-otg-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&otg_vbus_drv>; + regulator-name = "vcc_otg_5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + vin-supply = <&vcc_5v>; + }; +}; + +&cpu0 { + cpu0-supply = <&vdd_cpu>; +}; + +&emmc { + broken-cd; + bus-width = <8>; + cap-mmc-highspeed; + disable-wp; + non-removable; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_pwr>, <&emmc_bus8>; + vmmc-supply = <&vcc_io>; + vqmmc-supply = <&vcc_flash>; + status = "okay"; +}; + +&hdmi { + ddc-i2c-bus = <&i2c5>; + status = "okay"; +}; + +&i2c0 { + clock-frequency = <400000>; + status = "okay"; + + vdd_cpu: syr827@40 { + compatible = "silergy,syr827"; + fcs,suspend-voltage-selector = <1>; + reg = <0x40>; + regulator-name = "vdd_cpu"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc_sys>; + }; + + vdd_gpu: syr828@41 { + compatible = "silergy,syr828"; + fcs,suspend-voltage-selector = <1>; + reg = <0x41>; + regulator-name = "vdd_gpu"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + vin-supply = <&vcc_sys>; + }; + + hym8563: hym8563@51 { + compatible = "haoyu,hym8563"; + reg = <0x51>; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "xin32k"; + interrupt-parent = <&gpio7>; + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&rtc_int>; + }; + + act8846: act8846@5a { + compatible = "active-semi,act8846"; + reg = <0x5a>; + pinctrl-names = "default"; + pinctrl-0 = <&pwr_hold>; + system-power-controller; + + regulators { + vcc_ddr: REG1 { + regulator-name = "vcc_ddr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + vcc_io: REG2 { + regulator-name = "vcc_io"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_log: REG3 { + regulator-name = "vdd_log"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + vcc_20: REG4 { + regulator-name = "vcc_20"; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + regulator-always-on; + }; + + vccio_sd: REG5 { + regulator-name = "vccio_sd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd10_lcd: REG6 { + regulator-name = "vdd10_lcd"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + vcca_codec: REG7 { + regulator-name = "vcca_codec"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vcc_tp: REG8 { + regulator-name = "vcca_33"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vccio_pmu: REG9 { + regulator-name = "vccio_pmu"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vdd_10: REG10 { + regulator-name = "vdd_10"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + vcc_18: REG11 { + regulator-name = "vcc_18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + vcc18_lcd: REG12 { + regulator-name = "vcc18_lcd"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + }; + }; +}; + +&i2c1 { + status = "okay"; +}; + +&i2c2 { + status = "okay"; +}; + +&i2c4 { + status = "okay"; +}; + +&i2c5 { + status = "okay"; +}; + +&pinctrl { + pcfg_output_high: pcfg-output-high { + output-high; + }; + + pcfg_output_low: pcfg-output-low { + output-low; + }; + + act8846 { + pwr_hold: pwr-hold { + rockchip,pins = <0 9 RK_FUNC_GPIO &pcfg_output_high>; + }; + }; + + hym8563 { + rtc_int: rtc-int { + rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + keys { + pwr_key: pwr-key { + rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + sdmmc { + sdmmc_pwr: sdmmc-pwr { + rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + usb_host { + host_vbus_drv: host-vbus-drv { + rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + usb_otg { + otg_vbus_drv: otg-vbus-drv { + rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +}; + +&saradc { + vref-supply = <&vcc_18>; + status = "okay"; +}; + +&sdio0 { + broken-cd; + bus-width = <4>; + disable-wp; + non-removable; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&sdio0_bus4>, <&sdio0_cmd>, <&sdio0_clk>; + vmmc-supply = <&vcc_18>; + status = "disabled"; +}; + +&sdmmc { + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + card-detect-delay = <200>; + disable-wp; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_cd>, <&sdmmc_bus4>; + vmmc-supply = <&vccio_sd>; + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_clk>, <&spi0_cs0>, <&spi0_tx>, <&spi0_rx>, <&spi0_cs1>; + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>; + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +}; + +&usb_host1 { + status = "okay"; +}; + +&usb_otg { + status = "okay"; +}; + +&vopb { + status = "okay"; +}; + +&vopb_mmu { + status = "okay"; +}; + +&vopl { + status = "okay"; +}; + +&vopl_mmu { + status = "okay"; +}; + +&wdt { + status = "okay"; +}; diff --git a/arch/arm/dts/rk3288.dtsi b/arch/arm/dts/rk3288.dtsi index 3dab0fc..bcf051a 100644 --- a/arch/arm/dts/rk3288.dtsi +++ b/arch/arm/dts/rk3288.dtsi @@ -454,6 +454,7 @@ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cru HCLK_OTG0>; clock-names = "otg"; + dr_mode = "otg"; phys = <&usbphy0>; phy-names = "usb2-phy"; status = "disabled"; diff --git a/arch/arm/dts/rk3399-evb.dts b/arch/arm/dts/rk3399-evb.dts new file mode 100644 index 0000000..bbcfcd0 --- /dev/null +++ b/arch/arm/dts/rk3399-evb.dts @@ -0,0 +1,104 @@ +/* + * (C) Copyright 2016 Rockchip Electronics Co., Ltd + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/dts-v1/; +#include <dt-bindings/pwm/pwm.h> +#include "rk3399.dtsi" + +/ { + model = "Rockchip RK3399 Evaluation Board"; + compatible = "rockchip,rk3399-evb", "rockchip,rk3399", + "google,rk3399evb-rev2"; + + chosen { + stdout-path = &uart2; + }; + + vdd_center: vdd-center { + compatible = "pwm-regulator"; + pwms = <&pwm3 0 25000 0>; + regulator-name = "vdd_center"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + regulator-boot-on; + status = "okay"; + }; + + vcc3v3_sys: vcc3v3-sys { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vcc_phy: vcc-phy-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_phy"; + regulator-always-on; + regulator-boot-on; + }; +}; + +&emmc_phy { + status = "okay"; +}; + +&pwm0 { + status = "okay"; +}; + +&pwm2 { + status = "okay"; +}; + +&pwm3 { + status = "okay"; +}; + +&sdhci { + bus-width = <8>; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + non-removable; + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&usb_host0_ehci { + status = "okay"; +}; + +&usb_host0_ohci { + status = "okay"; +}; + +&usb_host1_ehci { + status = "okay"; +}; + +&usb_host1_ohci { + status = "okay"; +}; + +&pinctrl { + pmic { + pmic_int_l: pmic-int-l { + rockchip,pins = + <1 21 RK_FUNC_GPIO &pcfg_pull_up>; + }; + + pmic_dvs2: pmic-dvs2 { + rockchip,pins = + <1 18 RK_FUNC_GPIO &pcfg_pull_down>; + }; + }; +}; diff --git a/arch/arm/dts/rk3399.dtsi b/arch/arm/dts/rk3399.dtsi new file mode 100644 index 0000000..fb5af54 --- /dev/null +++ b/arch/arm/dts/rk3399.dtsi @@ -0,0 +1,1028 @@ +/* + * (C) Copyright 2016 Rockchip Electronics Co., Ltd + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <dt-bindings/clock/rk3399-cru.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pinctrl/rockchip.h> + +/ { + compatible = "rockchip,rk3399"; + + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + aliases { + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + }; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + cpu-map { + cluster0 { + core0 { + cpu = <&cpu_l0>; + }; + core1 { + cpu = <&cpu_l1>; + }; + core2 { + cpu = <&cpu_l2>; + }; + core3 { + cpu = <&cpu_l3>; + }; + }; + + cluster1 { + core0 { + cpu = <&cpu_b0>; + }; + core1 { + cpu = <&cpu_b1>; + }; + }; + }; + + cpu_l0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x0>; + enable-method = "psci"; + #cooling-cells = <2>; /* min followed by max */ + clocks = <&cru ARMCLKL>; + }; + + cpu_l1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x1>; + enable-method = "psci"; + clocks = <&cru ARMCLKL>; + }; + + cpu_l2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x2>; + enable-method = "psci"; + clocks = <&cru ARMCLKL>; + }; + + cpu_l3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x3>; + enable-method = "psci"; + clocks = <&cru ARMCLKL>; + }; + + cpu_b0: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a72", "arm,armv8"; + reg = <0x0 0x100>; + enable-method = "psci"; + #cooling-cells = <2>; /* min followed by max */ + clocks = <&cru ARMCLKB>; + }; + + cpu_b1: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a72", "arm,armv8"; + reg = <0x0 0x101>; + enable-method = "psci"; + clocks = <&cru ARMCLKB>; + }; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; + }; + + xin24m: xin24m { + compatible = "fixed-clock"; + clock-frequency = <24000000>; + clock-output-names = "xin24m"; + #clock-cells = <0>; + }; + + amba { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + dmac_bus: dma-controller@ff6d0000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x0 0xff6d0000 0x0 0x4000>; + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; + clocks = <&cru ACLK_DMAC0_PERILP>; + clock-names = "apb_pclk"; + }; + + dmac_peri: dma-controller@ff6e0000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x0 0xff6e0000 0x0 0x4000>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; + clocks = <&cru ACLK_DMAC1_PERILP>; + clock-names = "apb_pclk"; + }; + }; + + sdio0: dwmmc@fe310000 { + compatible = "rockchip,rk3399-dw-mshc", + "rockchip,rk3288-dw-mshc"; + reg = <0x0 0xfe310000 0x0 0x4000>; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; + clock-freq-min-max = <400000 150000000>; + clocks = <&cru HCLK_SDIO>, <&cru SCLK_SDIO>, + <&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>; + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; + fifo-depth = <0x100>; + status = "disabled"; + }; + + sdmmc: dwmmc@fe320000 { + compatible = "rockchip,rk3399-dw-mshc", + "rockchip,rk3288-dw-mshc"; + reg = <0x0 0xfe320000 0x0 0x4000>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; + clock-freq-min-max = <400000 150000000>; + clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>, + <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>; + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; + fifo-depth = <0x100>; + status = "disabled"; + }; + + sdhci: sdhci@fe330000 { + compatible = "rockchip,rk3399-sdhci-5.1", "arasan,sdhci-5.1"; + reg = <0x0 0xfe330000 0x0 0x10000>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + assigned-clocks = <&cru SCLK_EMMC>; + assigned-clock-rates = <200000000>; + clocks = <&cru SCLK_EMMC>, <&cru ACLK_EMMC>; + clock-names = "clk_xin", "clk_ahb"; + phys = <&emmc_phy>; + phy-names = "phy_arasan"; + status = "disabled"; + }; + + usb_host0_ehci: usb@fe380000 { + compatible = "generic-ehci"; + reg = <0x0 0xfe380000 0x0 0x20000>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>; + clock-names = "hclk_host0", "hclk_host0_arb"; + status = "disabled"; + }; + + usb_host0_ohci: usb@fe3a0000 { + compatible = "generic-ohci"; + reg = <0x0 0xfe3a0000 0x0 0x20000>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>; + clock-names = "hclk_host0", "hclk_host0_arb"; + status = "disabled"; + }; + + usb_host1_ehci: usb@fe3c0000 { + compatible = "generic-ehci"; + reg = <0x0 0xfe3c0000 0x0 0x20000>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>; + clock-names = "hclk_host1", "hclk_host1_arb"; + status = "disabled"; + }; + + usb_host1_ohci: usb@fe3e0000 { + compatible = "generic-ohci"; + reg = <0x0 0xfe3e0000 0x0 0x20000>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>; + clock-names = "hclk_host1", "hclk_host1_arb"; + status = "disabled"; + }; + + gic: interrupt-controller@fee00000 { + compatible = "arm,gic-v3"; + #interrupt-cells = <3>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + interrupt-controller; + + reg = <0x0 0xfee00000 0 0x10000>, /* GICD */ + <0x0 0xfef00000 0 0xc0000>, /* GICR */ + <0x0 0xfff00000 0 0x10000>, /* GICC */ + <0x0 0xfff10000 0 0x10000>, /* GICH */ + <0x0 0xfff20000 0 0x10000>; /* GICV */ + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + its: interrupt-controller@fee20000 { + compatible = "arm,gic-v3-its"; + msi-controller; + reg = <0x0 0xfee20000 0x0 0x20000>; + }; + }; + + uart0: serial@ff180000 { + compatible = "rockchip,rk3399-uart", "snps,dw-apb-uart"; + reg = <0x0 0xff180000 0x0 0x100>; + clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>; + clock-names = "baudclk", "apb_pclk"; + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&uart0_xfer>; + status = "disabled"; + }; + + uart1: serial@ff190000 { + compatible = "rockchip,rk3399-uart", "snps,dw-apb-uart"; + reg = <0x0 0xff190000 0x0 0x100>; + clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>; + clock-names = "baudclk", "apb_pclk"; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&uart1_xfer>; + status = "disabled"; + }; + + uart2: serial@ff1a0000 { + compatible = "rockchip,rk3399-uart", "snps,dw-apb-uart"; + reg = <0x0 0xff1a0000 0x0 0x100>; + clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>; + clock-names = "baudclk", "apb_pclk"; + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <24000000>; + reg-shift = <2>; + reg-io-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&uart2c_xfer>; + status = "disabled"; + }; + + uart3: serial@ff1b0000 { + compatible = "rockchip,rk3399-uart", "snps,dw-apb-uart"; + reg = <0x0 0xff1b0000 0x0 0x100>; + clocks = <&cru SCLK_UART3>, <&cru PCLK_UART3>; + clock-names = "baudclk", "apb_pclk"; + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&uart3_xfer>; + status = "disabled"; + }; + + spi0: spi@ff1c0000 { + compatible = "rockchip,rk3399-spi", "rockchip,rk3066-spi"; + reg = <0x0 0xff1c0000 0x0 0x1000>; + clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>; + clock-names = "spiclk", "apb_pclk"; + interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&spi0_clk &spi0_tx &spi0_rx &spi0_cs0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi1: spi@ff1d0000 { + compatible = "rockchip,rk3399-spi", "rockchip,rk3066-spi"; + reg = <0x0 0xff1d0000 0x0 0x1000>; + clocks = <&cru SCLK_SPI1>, <&cru PCLK_SPI1>; + clock-names = "spiclk", "apb_pclk"; + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&spi1_clk &spi1_tx &spi1_rx &spi1_cs0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi2: spi@ff1e0000 { + compatible = "rockchip,rk3399-spi", "rockchip,rk3066-spi"; + reg = <0x0 0xff1e0000 0x0 0x1000>; + clocks = <&cru SCLK_SPI2>, <&cru PCLK_SPI2>; + clock-names = "spiclk", "apb_pclk"; + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&spi2_clk &spi2_tx &spi2_rx &spi2_cs0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi4: spi@ff1f0000 { + compatible = "rockchip,rk3399-spi", "rockchip,rk3066-spi"; + reg = <0x0 0xff1f0000 0x0 0x1000>; + clocks = <&cru SCLK_SPI4>, <&cru PCLK_SPI4>; + clock-names = "spiclk", "apb_pclk"; + interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&spi4_clk &spi4_tx &spi4_rx &spi4_cs0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi5: spi@ff200000 { + compatible = "rockchip,rk3399-spi", "rockchip,rk3066-spi"; + reg = <0x0 0xff200000 0x0 0x1000>; + clocks = <&cru SCLK_SPI5>, <&cru PCLK_SPI5>; + clock-names = "spiclk", "apb_pclk"; + interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&spi5_clk &spi5_tx &spi5_rx &spi5_cs0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + pmugrf: syscon@ff320000 { + compatible = "rockchip,rk3399-pmugrf", "syscon", "simple-mfd"; + reg = <0x0 0xff320000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + pmu_io_domains: io-domains { + compatible = "rockchip,rk3399-pmu-io-voltage-domain"; + status = "disabled"; + }; + }; + + spi3: spi@ff350000 { + compatible = "rockchip,rk3399-spi", "rockchip,rk3066-spi"; + reg = <0x0 0xff350000 0x0 0x1000>; + clocks = <&pmucru SCLK_SPI3_PMU>, <&pmucru PCLK_SPI3_PMU>; + clock-names = "spiclk", "apb_pclk"; + interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&spi3_clk &spi3_tx &spi3_rx &spi3_cs0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + uart4: serial@ff370000 { + compatible = "rockchip,rk3399-uart", "snps,dw-apb-uart"; + reg = <0x0 0xff370000 0x0 0x100>; + clocks = <&pmucru SCLK_UART4_PMU>, <&pmucru PCLK_UART4_PMU>; + clock-names = "baudclk", "apb_pclk"; + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&uart4_xfer>; + status = "disabled"; + }; + + pwm0: pwm@ff420000 { + compatible = "rockchip,rk3399-pwm", "rockchip,rk3288-pwm"; + reg = <0x0 0xff420000 0x0 0x10>; + #pwm-cells = <3>; + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pin>; + clocks = <&pmucru PCLK_RKPWM_PMU>; + clock-names = "pwm"; + status = "disabled"; + }; + + pwm1: pwm@ff420010 { + compatible = "rockchip,rk3399-pwm", "rockchip,rk3288-pwm"; + reg = <0x0 0xff420010 0x0 0x10>; + #pwm-cells = <3>; + pinctrl-names = "default"; + pinctrl-0 = <&pwm1_pin>; + clocks = <&pmucru PCLK_RKPWM_PMU>; + clock-names = "pwm"; + status = "disabled"; + }; + + pwm2: pwm@ff420020 { + compatible = "rockchip,rk3399-pwm", "rockchip,rk3288-pwm"; + reg = <0x0 0xff420020 0x0 0x10>; + #pwm-cells = <3>; + pinctrl-names = "default"; + pinctrl-0 = <&pwm2_pin>; + clocks = <&pmucru PCLK_RKPWM_PMU>; + clock-names = "pwm"; + status = "disabled"; + }; + + pwm3: pwm@ff420030 { + compatible = "rockchip,rk3399-pwm", "rockchip,rk3288-pwm"; + reg = <0x0 0xff420030 0x0 0x10>; + #pwm-cells = <3>; + pinctrl-names = "default"; + pinctrl-0 = <&pwm3a_pin>; + clocks = <&pmucru PCLK_RKPWM_PMU>; + clock-names = "pwm"; + status = "disabled"; + }; + + pmucru: pmu-clock-controller@ff750000 { + compatible = "rockchip,rk3399-pmucru"; + reg = <0x0 0xff750000 0x0 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + assigned-clocks = <&pmucru PLL_PPLL>; + assigned-clock-rates = <676000000>; + }; + + cru: clock-controller@ff760000 { + compatible = "rockchip,rk3399-cru"; + reg = <0x0 0xff760000 0x0 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + assigned-clocks = + <&cru PLL_GPLL>, <&cru PLL_CPLL>, + <&cru PLL_NPLL>, + <&cru ACLK_PERIHP>, <&cru HCLK_PERIHP>, + <&cru PCLK_PERIHP>, + <&cru ACLK_PERILP0>, <&cru HCLK_PERILP0>, + <&cru PCLK_PERILP0>, + <&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>; + assigned-clock-rates = + <594000000>, <800000000>, + <1000000000>, + <150000000>, <75000000>, + <37500000>, + <100000000>, <100000000>, + <50000000>, + <100000000>, <50000000>; + }; + + grf: syscon@ff770000 { + compatible = "rockchip,rk3399-grf", "syscon", "simple-mfd"; + reg = <0x0 0xff770000 0x0 0x10000>; + #address-cells = <1>; + #size-cells = <1>; + + io_domains: io-domains { + compatible = "rockchip,rk3399-io-voltage-domain"; + status = "disabled"; + }; + + emmc_phy: phy@f780 { + compatible = "rockchip,rk3399-emmc-phy"; + reg = <0xf780 0x24>; + #phy-cells = <0>; + status = "disabled"; + }; + }; + + watchdog@ff840000 { + compatible = "snps,dw-wdt"; + reg = <0x0 0xff840000 0x0 0x100>; + clocks = <&cru PCLK_WDT>; + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + }; + + spdif: spdif@ff870000 { + compatible = "rockchip,rk3399-spdif"; + reg = <0x0 0xff870000 0x0 0x1000>; + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dmac_bus 7>; + dma-names = "tx"; + clock-names = "mclk", "hclk"; + clocks = <&cru SCLK_SPDIF_8CH>, <&cru HCLK_SPDIF>; + pinctrl-names = "default"; + pinctrl-0 = <&spdif_bus>; + status = "disabled"; + }; + + i2s0: i2s@ff880000 { + compatible = "rockchip,rk3399-i2s", "rockchip,rk3066-i2s"; + reg = <0x0 0xff880000 0x0 0x1000>; + rockchip,grf = <&grf>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dmac_bus 0>, <&dmac_bus 1>; + dma-names = "tx", "rx"; + clock-names = "i2s_clk", "i2s_hclk"; + clocks = <&cru SCLK_I2S0_8CH>, <&cru HCLK_I2S0_8CH>; + pinctrl-names = "default"; + pinctrl-0 = <&i2s0_8ch_bus>; + status = "disabled"; + }; + + i2s1: i2s@ff890000 { + compatible = "rockchip,rk3399-i2s", "rockchip,rk3066-i2s"; + reg = <0x0 0xff890000 0x0 0x1000>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dmac_bus 2>, <&dmac_bus 3>; + dma-names = "tx", "rx"; + clock-names = "i2s_clk", "i2s_hclk"; + clocks = <&cru SCLK_I2S1_8CH>, <&cru HCLK_I2S1_8CH>; + pinctrl-names = "default"; + pinctrl-0 = <&i2s1_2ch_bus>; + status = "disabled"; + }; + + i2s2: i2s@ff8a0000 { + compatible = "rockchip,rk3399-i2s", "rockchip,rk3066-i2s"; + reg = <0x0 0xff8a0000 0x0 0x1000>; + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dmac_bus 4>, <&dmac_bus 5>; + dma-names = "tx", "rx"; + clock-names = "i2s_clk", "i2s_hclk"; + clocks = <&cru SCLK_I2S2_8CH>, <&cru HCLK_I2S2_8CH>; + status = "disabled"; + }; + + pinctrl: pinctrl { + compatible = "rockchip,rk3399-pinctrl"; + rockchip,grf = <&grf>; + rockchip,pmu = <&pmugrf>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + gpio0: gpio0@ff720000 { + compatible = "rockchip,gpio-bank"; + reg = <0x0 0xff720000 0x0 0x100>; + clocks = <&pmucru PCLK_GPIO0_PMU>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + + gpio-controller; + #gpio-cells = <0x2>; + + interrupt-controller; + #interrupt-cells = <0x2>; + }; + + gpio1: gpio1@ff730000 { + compatible = "rockchip,gpio-bank"; + reg = <0x0 0xff730000 0x0 0x100>; + clocks = <&pmucru PCLK_GPIO1_PMU>; + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; + + gpio-controller; + #gpio-cells = <0x2>; + + interrupt-controller; + #interrupt-cells = <0x2>; + }; + + gpio2: gpio2@ff780000 { + compatible = "rockchip,gpio-bank"; + reg = <0x0 0xff780000 0x0 0x100>; + clocks = <&cru PCLK_GPIO2>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + + gpio-controller; + #gpio-cells = <0x2>; + + interrupt-controller; + #interrupt-cells = <0x2>; + }; + + gpio3: gpio3@ff788000 { + compatible = "rockchip,gpio-bank"; + reg = <0x0 0xff788000 0x0 0x100>; + clocks = <&cru PCLK_GPIO3>; + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; + + gpio-controller; + #gpio-cells = <0x2>; + + interrupt-controller; + #interrupt-cells = <0x2>; + }; + + gpio4: gpio4@ff790000 { + compatible = "rockchip,gpio-bank"; + reg = <0x0 0xff790000 0x0 0x100>; + clocks = <&cru PCLK_GPIO4>; + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; + + gpio-controller; + #gpio-cells = <0x2>; + + interrupt-controller; + #interrupt-cells = <0x2>; + }; + + pcfg_pull_up: pcfg-pull-up { + bias-pull-up; + }; + + pcfg_pull_down: pcfg-pull-down { + bias-pull-down; + }; + + pcfg_pull_none: pcfg-pull-none { + bias-disable; + }; + + pcfg_pull_none_12ma: pcfg-pull-none-12ma { + bias-disable; + drive-strength = <12>; + }; + + pcfg_pull_up_8ma: pcfg-pull-up-8ma { + bias-pull-up; + drive-strength = <8>; + }; + + pcfg_pull_down_4ma: pcfg-pull-down-4ma { + bias-pull-down; + drive-strength = <4>; + }; + + pcfg_pull_up_2ma: pcfg-pull-up-2ma { + bias-pull-up; + drive-strength = <2>; + }; + + pcfg_pull_down_12ma: pcfg-pull-down-12ma { + bias-pull-down; + drive-strength = <12>; + }; + + pcfg_pull_none_13ma: pcfg-pull-none-13ma { + bias-disable; + drive-strength = <13>; + }; + + i2c0 { + i2c0_xfer: i2c0-xfer { + rockchip,pins = + <1 15 RK_FUNC_2 &pcfg_pull_none>, + <1 16 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + i2c1 { + i2c1_xfer: i2c1-xfer { + rockchip,pins = + <4 2 RK_FUNC_1 &pcfg_pull_none>, + <4 1 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + i2c2 { + i2c2_xfer: i2c2-xfer { + rockchip,pins = + <2 1 RK_FUNC_2 &pcfg_pull_none_12ma>, + <2 0 RK_FUNC_2 &pcfg_pull_none_12ma>; + }; + }; + + i2c3 { + i2c3_xfer: i2c3-xfer { + rockchip,pins = + <4 17 RK_FUNC_1 &pcfg_pull_none>, + <4 16 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + i2c4 { + i2c4_xfer: i2c4-xfer { + rockchip,pins = + <1 12 RK_FUNC_1 &pcfg_pull_none>, + <1 11 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + i2c5 { + i2c5_xfer: i2c5-xfer { + rockchip,pins = + <3 11 RK_FUNC_2 &pcfg_pull_none>, + <3 10 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + i2c6 { + i2c6_xfer: i2c6-xfer { + rockchip,pins = + <2 10 RK_FUNC_2 &pcfg_pull_none>, + <2 9 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + i2c7 { + i2c7_xfer: i2c7-xfer { + rockchip,pins = + <2 8 RK_FUNC_2 &pcfg_pull_none>, + <2 7 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + i2c8 { + i2c8_xfer: i2c8-xfer { + rockchip,pins = + <1 21 RK_FUNC_1 &pcfg_pull_none>, + <1 20 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + i2s0 { + i2s0_8ch_bus: i2s0-8ch-bus { + rockchip,pins = + <3 24 RK_FUNC_1 &pcfg_pull_none>, + <3 25 RK_FUNC_1 &pcfg_pull_none>, + <3 26 RK_FUNC_1 &pcfg_pull_none>, + <3 27 RK_FUNC_1 &pcfg_pull_none>, + <3 28 RK_FUNC_1 &pcfg_pull_none>, + <3 29 RK_FUNC_1 &pcfg_pull_none>, + <3 30 RK_FUNC_1 &pcfg_pull_none>, + <3 31 RK_FUNC_1 &pcfg_pull_none>, + <4 0 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + i2s1 { + i2s1_2ch_bus: i2s1-2ch-bus { + rockchip,pins = + <4 3 RK_FUNC_1 &pcfg_pull_none>, + <4 4 RK_FUNC_1 &pcfg_pull_none>, + <4 5 RK_FUNC_1 &pcfg_pull_none>, + <4 6 RK_FUNC_1 &pcfg_pull_none>, + <4 7 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + spdif { + spdif_bus: spdif-bus { + rockchip,pins = + <4 21 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + spi0 { + spi0_clk: spi0-clk { + rockchip,pins = + <3 6 RK_FUNC_2 &pcfg_pull_up>; + }; + spi0_cs0: spi0-cs0 { + rockchip,pins = + <3 7 RK_FUNC_2 &pcfg_pull_up>; + }; + spi0_cs1: spi0-cs1 { + rockchip,pins = + <3 8 RK_FUNC_2 &pcfg_pull_up>; + }; + spi0_tx: spi0-tx { + rockchip,pins = + <3 5 RK_FUNC_2 &pcfg_pull_up>; + }; + spi0_rx: spi0-rx { + rockchip,pins = + <3 4 RK_FUNC_2 &pcfg_pull_up>; + }; + }; + + spi1 { + spi1_clk: spi1-clk { + rockchip,pins = + <1 9 RK_FUNC_2 &pcfg_pull_up>; + }; + spi1_cs0: spi1-cs0 { + rockchip,pins = + <1 10 RK_FUNC_2 &pcfg_pull_up>; + }; + spi1_rx: spi1-rx { + rockchip,pins = + <1 7 RK_FUNC_2 &pcfg_pull_up>; + }; + spi1_tx: spi1-tx { + rockchip,pins = + <1 8 RK_FUNC_2 &pcfg_pull_up>; + }; + }; + + spi2 { + spi2_clk: spi2-clk { + rockchip,pins = + <2 11 RK_FUNC_1 &pcfg_pull_up>; + }; + spi2_cs0: spi2-cs0 { + rockchip,pins = + <2 12 RK_FUNC_1 &pcfg_pull_up>; + }; + spi2_rx: spi2-rx { + rockchip,pins = + <2 9 RK_FUNC_1 &pcfg_pull_up>; + }; + spi2_tx: spi2-tx { + rockchip,pins = + <2 10 RK_FUNC_1 &pcfg_pull_up>; + }; + }; + + spi3 { + spi3_clk: spi3-clk { + rockchip,pins = + <1 17 RK_FUNC_1 &pcfg_pull_up>; + }; + spi3_cs0: spi3-cs0 { + rockchip,pins = + <1 18 RK_FUNC_1 &pcfg_pull_up>; + }; + spi3_rx: spi3-rx { + rockchip,pins = + <1 15 RK_FUNC_1 &pcfg_pull_up>; + }; + spi3_tx: spi3-tx { + rockchip,pins = + <1 16 RK_FUNC_1 &pcfg_pull_up>; + }; + }; + + spi4 { + spi4_clk: spi4-clk { + rockchip,pins = + <3 2 RK_FUNC_2 &pcfg_pull_up>; + }; + spi4_cs0: spi4-cs0 { + rockchip,pins = + <3 3 RK_FUNC_2 &pcfg_pull_up>; + }; + spi4_rx: spi4-rx { + rockchip,pins = + <3 0 RK_FUNC_2 &pcfg_pull_up>; + }; + spi4_tx: spi4-tx { + rockchip,pins = + <3 1 RK_FUNC_2 &pcfg_pull_up>; + }; + }; + + spi5 { + spi5_clk: spi5-clk { + rockchip,pins = + <2 22 RK_FUNC_2 &pcfg_pull_up>; + }; + spi5_cs0: spi5-cs0 { + rockchip,pins = + <2 23 RK_FUNC_2 &pcfg_pull_up>; + }; + spi5_rx: spi5-rx { + rockchip,pins = + <2 20 RK_FUNC_2 &pcfg_pull_up>; + }; + spi5_tx: spi5-tx { + rockchip,pins = + <2 21 RK_FUNC_2 &pcfg_pull_up>; + }; + }; + + uart0 { + uart0_xfer: uart0-xfer { + rockchip,pins = + <2 16 RK_FUNC_1 &pcfg_pull_up>, + <2 17 RK_FUNC_1 &pcfg_pull_none>; + }; + + uart0_cts: uart0-cts { + rockchip,pins = + <2 18 RK_FUNC_1 &pcfg_pull_none>; + }; + + uart0_rts: uart0-rts { + rockchip,pins = + <2 19 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + uart1 { + uart1_xfer: uart1-xfer { + rockchip,pins = + <3 12 RK_FUNC_2 &pcfg_pull_up>, + <3 13 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + uart2a { + uart2a_xfer: uart2a-xfer { + rockchip,pins = + <4 8 RK_FUNC_2 &pcfg_pull_up>, + <4 9 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + uart2b { + uart2b_xfer: uart2b-xfer { + rockchip,pins = + <4 16 RK_FUNC_2 &pcfg_pull_up>, + <4 17 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + uart2c { + uart2c_xfer: uart2c-xfer { + rockchip,pins = + <4 19 RK_FUNC_1 &pcfg_pull_up>, + <4 20 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + uart3 { + uart3_xfer: uart3-xfer { + rockchip,pins = + <3 14 RK_FUNC_2 &pcfg_pull_up>, + <3 15 RK_FUNC_2 &pcfg_pull_none>; + }; + + uart3_cts: uart3-cts { + rockchip,pins = + <3 18 RK_FUNC_2 &pcfg_pull_none>; + }; + + uart3_rts: uart3-rts { + rockchip,pins = + <3 19 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + uart4 { + uart4_xfer: uart4-xfer { + rockchip,pins = + <1 7 RK_FUNC_1 &pcfg_pull_up>, + <1 8 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + uarthdcp { + uarthdcp_xfer: uarthdcp-xfer { + rockchip,pins = + <4 21 RK_FUNC_2 &pcfg_pull_up>, + <4 22 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + pwm0 { + pwm0_pin: pwm0-pin { + rockchip,pins = + <4 18 RK_FUNC_1 &pcfg_pull_none>; + }; + + vop0_pwm_pin: vop0-pwm-pin { + rockchip,pins = + <4 18 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + pwm1 { + pwm1_pin: pwm1-pin { + rockchip,pins = + <4 22 RK_FUNC_1 &pcfg_pull_none>; + }; + + vop1_pwm_pin: vop1-pwm-pin { + rockchip,pins = + <4 18 RK_FUNC_3 &pcfg_pull_none>; + }; + }; + + pwm2 { + pwm2_pin: pwm2-pin { + rockchip,pins = + <1 19 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + pwm3a { + pwm3a_pin: pwm3a-pin { + rockchip,pins = + <0 6 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + pwm3b { + pwm3b_pin: pwm3b-pin { + rockchip,pins = + <1 14 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + }; +}; diff --git a/arch/arm/dts/sun5i-a10s.dtsi b/arch/arm/dts/sun5i-a10s.dtsi index bddd0de..a5f8855 100644 --- a/arch/arm/dts/sun5i-a10s.dtsi +++ b/arch/arm/dts/sun5i-a10s.dtsi @@ -241,6 +241,20 @@ allwinner,drive = <SUN4I_PINCTRL_30_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + + nand_cs2_pins_a: nand_cs@2 { + allwinner,pins = "PC17"; + allwinner,function = "nand0"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + nand_cs3_pins_a: nand_cs@3 { + allwinner,pins = "PC18"; + allwinner,function = "nand0"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; }; &sram_a { diff --git a/arch/arm/dts/sun5i-a13-olinuxino.dts b/arch/arm/dts/sun5i-a13-olinuxino.dts index b3c234c..30e069a 100644 --- a/arch/arm/dts/sun5i-a13-olinuxino.dts +++ b/arch/arm/dts/sun5i-a13-olinuxino.dts @@ -155,6 +155,21 @@ status = "okay"; }; +&nfc { + pinctrl-names = "default"; + pinctrl-0 = <&nand_pins_a &nand_cs0_pins_a &nand_rb0_pins_a>; + status = "okay"; + + nand@0 { + #address-cells = <2>; + #size-cells = <2>; + reg = <0>; + allwinner,rb = <0>; + nand-ecc-mode = "hw"; + allwinner,randomize; + }; +}; + &ohci0 { status = "okay"; }; diff --git a/arch/arm/dts/sun5i-r8-chip.dts b/arch/arm/dts/sun5i-r8-chip.dts index 6ad19e2..b1b62d5 100644 --- a/arch/arm/dts/sun5i-r8-chip.dts +++ b/arch/arm/dts/sun5i-r8-chip.dts @@ -142,6 +142,21 @@ status = "okay"; }; +&nfc { + pinctrl-names = "default"; + pinctrl-0 = <&nand_pins_a &nand_cs0_pins_a &nand_rb0_pins_a>; + status = "okay"; + + nand@0 { + #address-cells = <2>; + #size-cells = <2>; + reg = <0>; + allwinner,rb = <0>; + nand-ecc-mode = "hw"; + nand-on-flash-bbt; + }; +}; + &ohci0 { status = "okay"; }; diff --git a/arch/arm/dts/sun5i.dtsi b/arch/arm/dts/sun5i.dtsi index 59a9426..87e5353 100644 --- a/arch/arm/dts/sun5i.dtsi +++ b/arch/arm/dts/sun5i.dtsi @@ -356,6 +356,17 @@ #dma-cells = <2>; }; + nfc: nand@01c03000 { + compatible = "allwinner,sun4i-a10-nand"; + reg = <0x01c03000 0x1000>; + interrupts = <37>; + clocks = <&ahb_gates 13>, <&nand_clk>; + clock-names = "ahb", "mod"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + spi0: spi@01c05000 { compatible = "allwinner,sun4i-a10-spi"; reg = <0x01c05000 0x1000>; @@ -548,6 +559,44 @@ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; }; + nand_pins_a: nand_base0@0 { + allwinner,pins = "PC0", "PC1", "PC2", + "PC5", "PC8", "PC9", "PC10", + "PC11", "PC12", "PC13", "PC14", + "PC15"; + allwinner,function = "nand0"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + nand_cs0_pins_a: nand_cs@0 { + allwinner,pins = "PC4"; + allwinner,function = "nand0"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + nand_cs1_pins_a: nand_cs@1 { + allwinner,pins = "PC3"; + allwinner,function = "nand0"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + nand_rb0_pins_a: nand_rb@0 { + allwinner,pins = "PC6"; + allwinner,function = "nand0"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + nand_rb1_pins_a: nand_rb@1 { + allwinner,pins = "PC7"; + allwinner,function = "nand0"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + uart3_pins_a: uart3@0 { allwinner,pins = "PG9", "PG10"; allwinner,function = "uart3"; diff --git a/arch/arm/include/asm/arch-fsl-layerscape/config.h b/arch/arm/include/asm/arch-fsl-layerscape/config.h index 44fe0c0..b0ad4b4 100644 --- a/arch/arm/include/asm/arch-fsl-layerscape/config.h +++ b/arch/arm/include/asm/arch-fsl-layerscape/config.h @@ -149,43 +149,43 @@ #define CONFIG_ARM_ERRATA_833471 #define CONFIG_SYS_FSL_MAX_NUM_OF_SEC 1 -#elif defined(CONFIG_LS1043A) -#define CONFIG_MAX_CPUS 4 +#elif defined(CONFIG_FSL_LSCH2) #define CONFIG_SYS_CACHELINE_SIZE 64 -#define CONFIG_SYS_FMAN_V3 -#define CONFIG_SYS_NUM_FMAN 1 -#define CONFIG_SYS_NUM_FM1_DTSEC 7 -#define CONFIG_SYS_NUM_FM1_10GEC 1 -#define CONFIG_SYS_FSL_IFC_BANK_COUNT 4 #define CONFIG_NUM_DDR_CONTROLLERS 1 -#define CONFIG_SYS_CCSRBAR_DEFAULT 0x01000000 #define CONFIG_SYS_FSL_SEC_COMPAT 5 #define CONFIG_SYS_FSL_OCRAM_BASE 0x10000000 /* initial RAM */ -#define CONFIG_SYS_FSL_OCRAM_SIZE 0x200000 /* 2 MiB */ -#define CONFIG_SYS_FSL_DDR_BE -#define CONFIG_SYS_DDR_BLOCK1_SIZE ((phys_size_t)2 << 30) -#define CONFIG_MAX_MEM_MAPPED CONFIG_SYS_DDR_BLOCK1_SIZE +#define CONFIG_SYS_FSL_OCRAM_SIZE 0x00200000 /* 2M */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0x01000000 -#define CONFIG_SYS_FSL_CCSR_GUR_BE #define CONFIG_SYS_FSL_CCSR_SCFG_BE -#define CONFIG_SYS_FSL_IFC_BE #define CONFIG_SYS_FSL_ESDHC_BE #define CONFIG_SYS_FSL_WDOG_BE #define CONFIG_SYS_FSL_DSPI_BE #define CONFIG_SYS_FSL_QSPI_BE +#define CONFIG_SYS_FSL_CCSR_GUR_BE #define CONFIG_SYS_FSL_PEX_LUT_BE +#define CONFIG_SYS_FSL_SEC_BE + +#define CONFIG_SYS_FSL_SRDS_1 +/* SoC related */ +#ifdef CONFIG_LS1043A +#define CONFIG_MAX_CPUS 4 +#define CONFIG_SYS_FMAN_V3 +#define CONFIG_SYS_NUM_FMAN 1 +#define CONFIG_SYS_NUM_FM1_DTSEC 7 +#define CONFIG_SYS_NUM_FM1_10GEC 1 +#define CONFIG_SYS_FSL_IFC_BANK_COUNT 4 +#define CONFIG_SYS_FSL_DDR_BE +#define CONFIG_SYS_DDR_BLOCK1_SIZE ((phys_size_t)2 << 30) +#define CONFIG_MAX_MEM_MAPPED CONFIG_SYS_DDR_BLOCK1_SIZE #define QE_MURAM_SIZE 0x6000UL #define MAX_QE_RISC 1 #define QE_NUM_OF_SNUM 28 -#define SRDS_MAX_LANES 4 -#define CONFIG_SYS_FSL_SRDS_1 -#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.4" - +#define CONFIG_SYS_FSL_IFC_BE #define CONFIG_SYS_FSL_SFP_VER_3_2 #define CONFIG_SYS_FSL_SEC_MON_BE -#define CONFIG_SYS_FSL_SEC_BE #define CONFIG_SYS_FSL_SFP_BE #define CONFIG_SYS_FSL_SRK_LE #define CONFIG_KEY_REVOCATION @@ -205,32 +205,40 @@ #define CONFIG_SYS_FSL_MAX_NUM_OF_SEC 1 #elif defined(CONFIG_LS1012A) #define CONFIG_MAX_CPUS 1 -#define CONFIG_SYS_CACHELINE_SIZE 64 -#define CONFIG_NUM_DDR_CONTROLLERS 1 -#define CONFIG_SYS_CCSRBAR_DEFAULT 0x01000000 -#define CONFIG_SYS_FSL_SEC_COMPAT 5 #undef CONFIG_SYS_FSL_DDRC_ARM_GEN3 -#define CONFIG_SYS_FSL_OCRAM_BASE 0x10000000 /* initial RAM */ -#define CONFIG_SYS_FSL_OCRAM_SIZE 0x200000 /* 2 MiB */ - #define GICD_BASE 0x01401000 #define GICC_BASE 0x01402000 +#elif defined(CONFIG_LS1046A) +#define CONFIG_MAX_CPUS 4 +#define CONFIG_SYS_FMAN_V3 +#define CONFIG_SYS_NUM_FMAN 1 +#define CONFIG_SYS_NUM_FM1_DTSEC 8 +#define CONFIG_SYS_NUM_FM1_10GEC 2 +#define CONFIG_SYS_FSL_IFC_BANK_COUNT 4 +#define CONFIG_SYS_FSL_DDR_BE +#define CONFIG_SYS_DDR_BLOCK1_SIZE ((phys_size_t)2 << 30) +#define CONFIG_MAX_MEM_MAPPED CONFIG_SYS_DDR_BLOCK1_SIZE -#define CONFIG_SYS_FSL_CCSR_GUR_BE -#define CONFIG_SYS_FSL_CCSR_SCFG_BE -#define CONFIG_SYS_FSL_ESDHC_BE -#define CONFIG_SYS_FSL_WDOG_BE -#define CONFIG_SYS_FSL_DSPI_BE -#define CONFIG_SYS_FSL_QSPI_BE -#define CONFIG_SYS_FSL_PEX_LUT_BE +#define CONFIG_SYS_FSL_SRDS_2 +#define CONFIG_SYS_FSL_IFC_BE +#define CONFIG_SYS_FSL_SFP_VER_3_2 +#define CONFIG_SYS_FSL_SNVS_LE +#define CONFIG_SYS_FSL_SFP_BE +#define CONFIG_SYS_FSL_SRK_LE +#define CONFIG_KEY_REVOCATION -#define SRDS_MAX_LANES 4 -#define CONFIG_SYS_FSL_SRDS_1 -#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.4" -#define CONFIG_SYS_FSL_SEC_BE +/* SMMU Defintions */ +#define SMMU_BASE 0x09000000 + +/* Generic Interrupt Controller Definitions */ +#define GICD_BASE 0x01410000 +#define GICC_BASE 0x01420000 + +#define CONFIG_SYS_FSL_MAX_NUM_OF_SEC 1 #else #error SoC not defined #endif +#endif #endif /* _ASM_ARMV8_FSL_LAYERSCAPE_CONFIG_H_ */ diff --git a/arch/arm/include/asm/arch-fsl-layerscape/cpu.h b/arch/arm/include/asm/arch-fsl-layerscape/cpu.h index 5fd5e87..e2d96a1 100644 --- a/arch/arm/include/asm/arch-fsl-layerscape/cpu.h +++ b/arch/arm/include/asm/arch-fsl-layerscape/cpu.h @@ -13,6 +13,8 @@ static struct cpu_type cpu_type_list[] = { CPU_TYPE_ENTRY(LS2045A, LS2045A, 4), CPU_TYPE_ENTRY(LS1043A, LS1043A, 4), CPU_TYPE_ENTRY(LS1023A, LS1023A, 2), + CPU_TYPE_ENTRY(LS1046A, LS1046A, 4), + CPU_TYPE_ENTRY(LS1026A, LS1026A, 2), CPU_TYPE_ENTRY(LS2040A, LS2040A, 4), CPU_TYPE_ENTRY(LS1012A, LS1012A, 1), }; diff --git a/arch/arm/include/asm/arch-fsl-layerscape/fsl_serdes.h b/arch/arm/include/asm/arch-fsl-layerscape/fsl_serdes.h index 487cba8..e1b3f44 100644 --- a/arch/arm/include/asm/arch-fsl-layerscape/fsl_serdes.h +++ b/arch/arm/include/asm/arch-fsl-layerscape/fsl_serdes.h @@ -140,6 +140,7 @@ enum srds_prtcl { enum srds { FSL_SRDS_1 = 0, + FSL_SRDS_2 = 1, }; #endif @@ -150,7 +151,7 @@ int serdes_get_first_lane(u32 sd, enum srds_prtcl device); enum srds_prtcl serdes_get_prtcl(int serdes, int cfg, int lane); int is_serdes_prtcl_valid(int serdes, u32 prtcl); -#ifdef CONFIG_LS1043A +#ifdef CONFIG_FSL_LSCH2 const char *serdes_clock_to_string(u32 clock); int get_serdes_protocol(void); #endif diff --git a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch2.h b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch2.h index 8b8a7c1..95a4293 100644 --- a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch2.h +++ b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch2.h @@ -31,9 +31,9 @@ #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x011c0600) #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_IMMR + 0x011d0500) #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_IMMR + 0x011d0600) -#define CONFIG_SYS_LS1043A_XHCI_USB1_ADDR (CONFIG_SYS_IMMR + 0x01f00000) -#define CONFIG_SYS_LS1043A_XHCI_USB2_ADDR (CONFIG_SYS_IMMR + 0x02000000) -#define CONFIG_SYS_LS1043A_XHCI_USB3_ADDR (CONFIG_SYS_IMMR + 0x02100000) +#define CONFIG_SYS_XHCI_USB1_ADDR (CONFIG_SYS_IMMR + 0x01f00000) +#define CONFIG_SYS_XHCI_USB2_ADDR (CONFIG_SYS_IMMR + 0x02000000) +#define CONFIG_SYS_XHCI_USB3_ADDR (CONFIG_SYS_IMMR + 0x02100000) #define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_IMMR + 0x2400000) #define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_IMMR + 0x2500000) #define CONFIG_SYS_PCIE3_ADDR (CONFIG_SYS_IMMR + 0x2600000) @@ -94,6 +94,7 @@ #define TY_ITYP_VER_A7 0x1 #define TY_ITYP_VER_A53 0x2 #define TY_ITYP_VER_A57 0x3 +#define TY_ITYP_VER_A72 0x4 #define TP_CLUSTER_EOC 0xc0000000 /* end of clusters */ #define TP_CLUSTER_INIT_MASK 0x0000003f /* initiator mask */ @@ -227,6 +228,8 @@ struct ccsr_gur { #define FSL_CHASSIS2_RCWSR0_MEM_PLL_RAT_MASK 0x3f #define FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK 0xffff0000 #define FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT 16 +#define FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_MASK 0x0000ffff +#define FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_SHIFT 0 #define RCW_SB_EN_REG_INDEX 7 #define RCW_SB_EN_MASK 0x00200000 diff --git a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h index 3ad46eb..93e26c1 100644 --- a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h +++ b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h @@ -52,8 +52,8 @@ #define I2C3_BASE_ADDR (CONFIG_SYS_IMMR + 0x01020000) #define I2C4_BASE_ADDR (CONFIG_SYS_IMMR + 0x01030000) -#define CONFIG_SYS_LS2080A_XHCI_USB1_ADDR (CONFIG_SYS_IMMR + 0x02100000) -#define CONFIG_SYS_LS2080A_XHCI_USB2_ADDR (CONFIG_SYS_IMMR + 0x02110000) +#define CONFIG_SYS_XHCI_USB1_ADDR (CONFIG_SYS_IMMR + 0x02100000) +#define CONFIG_SYS_XHCI_USB2_ADDR (CONFIG_SYS_IMMR + 0x02110000) /* TZ Address Space Controller Definitions */ #define TZASC1_BASE 0x01100000 /* as per CCSR map. */ @@ -156,6 +156,7 @@ #define TY_ITYP_VER_A7 0x1 #define TY_ITYP_VER_A53 0x2 #define TY_ITYP_VER_A57 0x3 +#define TY_ITYP_VER_A72 0x4 #define TP_CLUSTER_EOC 0x80000000 /* end of clusters */ #define TP_CLUSTER_INIT_MASK 0x0000003f /* initiator mask */ diff --git a/arch/arm/include/asm/arch-fsl-layerscape/soc.h b/arch/arm/include/asm/arch-fsl-layerscape/soc.h index 39e8c7a..8d4a7ad 100644 --- a/arch/arm/include/asm/arch-fsl-layerscape/soc.h +++ b/arch/arm/include/asm/arch-fsl-layerscape/soc.h @@ -44,6 +44,8 @@ struct cpu_type { #define SVR_LS1012A 0x870400 #define SVR_LS1043A 0x879200 #define SVR_LS1023A 0x879208 +#define SVR_LS1046A 0x870700 +#define SVR_LS1026A 0x870708 #define SVR_LS2045A 0x870120 #define SVR_LS2080A 0x870110 #define SVR_LS2085A 0x870100 diff --git a/arch/arm/include/asm/arch-ls102xa/config.h b/arch/arm/include/asm/arch-ls102xa/config.h index 04abec4..d408fe4 100644 --- a/arch/arm/include/asm/arch-ls102xa/config.h +++ b/arch/arm/include/asm/arch-ls102xa/config.h @@ -10,7 +10,7 @@ #define CONFIG_SYS_CACHELINE_SIZE 64 #define OCRAM_BASE_ADDR 0x10000000 -#define OCRAM_SIZE 0x00020000 +#define OCRAM_SIZE 0x00010000 #define OCRAM_BASE_S_ADDR 0x10010000 #define OCRAM_S_SIZE 0x00010000 @@ -32,16 +32,15 @@ #define CONFIG_SYS_FSL_SERDES_ADDR (CONFIG_SYS_IMMR + 0x00ea0000) #define CONFIG_SYS_FSL_GUTS_ADDR (CONFIG_SYS_IMMR + 0x00ee0000) #define CONFIG_SYS_FSL_LS1_CLK_ADDR (CONFIG_SYS_IMMR + 0x00ee1000) +#define CONFIG_SYS_FSL_RCPM_ADDR (CONFIG_SYS_IMMR + 0x00ee2000) #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x011c0500) #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x011d0500) #define CONFIG_SYS_DCU_ADDR (CONFIG_SYS_IMMR + 0x01ce0000) -#define CONFIG_SYS_LS102XA_XHCI_USB1_ADDR (CONFIG_SYS_IMMR + 0x02100000) -#define CONFIG_SYS_LS102XA_USB1_ADDR \ - (CONFIG_SYS_IMMR + CONFIG_SYS_LS102XA_USB1_OFFSET) +#define CONFIG_SYS_XHCI_USB1_ADDR (CONFIG_SYS_IMMR + 0x02100000) +#define CONFIG_SYS_EHCI_USB1_ADDR (CONFIG_SYS_IMMR + 0x07600000) #define CONFIG_SYS_FSL_SEC_OFFSET 0x00700000 #define CONFIG_SYS_FSL_JR0_OFFSET 0x00710000 -#define CONFIG_SYS_LS102XA_USB1_OFFSET 0x07600000 #define CONFIG_SYS_TSEC1_OFFSET 0x01d10000 #define CONFIG_SYS_TSEC2_OFFSET 0x01d50000 #define CONFIG_SYS_TSEC3_OFFSET 0x01d90000 diff --git a/arch/arm/include/asm/arch-omap4/i2c.h b/arch/arm/include/asm/arch-omap4/i2c.h index adc8eb2..463e979 100644 --- a/arch/arm/include/asm/arch-omap4/i2c.h +++ b/arch/arm/include/asm/arch-omap4/i2c.h @@ -14,9 +14,9 @@ struct i2c { unsigned short revnb_lo; /* 0x00 */ unsigned short res1; unsigned short revnb_hi; /* 0x04 */ - unsigned short res2[13]; - unsigned short sysc; /* 0x20 */ - unsigned short res3; + unsigned short res2[5]; + unsigned short sysc; /* 0x10 */ + unsigned short res3[9]; unsigned short irqstatus_raw; /* 0x24 */ unsigned short res4; unsigned short stat; /* 0x28 */ diff --git a/arch/arm/include/asm/arch-omap5/i2c.h b/arch/arm/include/asm/arch-omap5/i2c.h index d875cfe..2b55edf 100644 --- a/arch/arm/include/asm/arch-omap5/i2c.h +++ b/arch/arm/include/asm/arch-omap5/i2c.h @@ -14,9 +14,9 @@ struct i2c { unsigned short revnb_lo; /* 0x00 */ unsigned short res1; unsigned short revnb_hi; /* 0x04 */ - unsigned short res2[13]; - unsigned short sysc; /* 0x20 */ - unsigned short res3; + unsigned short res2[5]; + unsigned short sysc; /* 0x10 */ + unsigned short res3[9]; unsigned short irqstatus_raw; /* 0x24 */ unsigned short res4; unsigned short stat; /* 0x28 */ diff --git a/arch/arm/include/asm/arch-rockchip/clock.h b/arch/arm/include/asm/arch-rockchip/clock.h index 317e512..21edbc2 100644 --- a/arch/arm/include/asm/arch-rockchip/clock.h +++ b/arch/arm/include/asm/arch-rockchip/clock.h @@ -65,6 +65,8 @@ void *rockchip_get_cru(void); struct rk3288_cru; struct rk3288_grf; -void rkclk_configure_cpu(struct rk3288_cru *cru, struct rk3288_grf *grf); +void rk3288_clk_configure_cpu(struct rk3288_cru *cru, struct rk3288_grf *grf); + +int rockchip_get_clk(struct udevice **devp); #endif diff --git a/arch/arm/include/asm/arch-sunxi/clock_sun4i.h b/arch/arm/include/asm/arch-sunxi/clock_sun4i.h index 0088bb9..d1c5ad0 100644 --- a/arch/arm/include/asm/arch-sunxi/clock_sun4i.h +++ b/arch/arm/include/asm/arch-sunxi/clock_sun4i.h @@ -269,6 +269,11 @@ struct sunxi_ccm_reg { #define CCM_MBUS_CTRL_CLK_SRC_PLL5 0x2 #define CCM_MBUS_CTRL_GATE (0x1 << 31) +#define CCM_NAND_CTRL_M(x) ((x) - 1) +#define CCM_NAND_CTRL_N(x) ((x) << 16) +#define CCM_NAND_CTRL_OSCM24 (0x0 << 24) +#define CCM_NAND_CTRL_PLL6 (0x1 << 24) +#define CCM_NAND_CTRL_PLL5 (0x2 << 24) #define CCM_NAND_CTRL_ENABLE (0x1 << 31) #define CCM_MMC_CTRL_M(x) ((x) - 1) diff --git a/arch/arm/include/asm/fsl_secure_boot.h b/arch/arm/include/asm/fsl_secure_boot.h index 53cd755..b35c271 100644 --- a/arch/arm/include/asm/fsl_secure_boot.h +++ b/arch/arm/include/asm/fsl_secure_boot.h @@ -17,8 +17,6 @@ #ifdef CONFIG_CHAIN_OF_TRUST #define CONFIG_CMD_ESBC_VALIDATE -#define CONFIG_CMD_BLOB -#define CONFIG_CMD_HASH #define CONFIG_FSL_SEC_MON #define CONFIG_SHA_HW_ACCEL #define CONFIG_SHA_PROG_HW_ACCEL @@ -28,6 +26,28 @@ #define CONFIG_FSL_CAAM #endif +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SPL_BOARD_INIT +#define CONFIG_SPL_DM 1 +#define CONFIG_SPL_CRYPTO_SUPPORT +#define CONFIG_SPL_HASH_SUPPORT +#define CONFIG_SPL_RSA +#define CONFIG_SPL_DRIVERS_MISC_SUPPORT +/* + * Define the key hash for U-Boot here if public/private key pair used to + * sign U-boot are different from the SRK hash put in the fuse + * Example of defining KEY_HASH is + * #define CONFIG_SPL_UBOOT_KEY_HASH \ + * "41066b564c6ffcef40ccbc1e0a5d0d519604000c785d97bbefd25e4d288d1c8b" + * else leave it defined as NULL + */ + +#define CONFIG_SPL_UBOOT_KEY_HASH NULL +#endif /* ifdef CONFIG_SPL_BUILD */ + +#ifndef CONFIG_SPL_BUILD +#define CONFIG_CMD_BLOB +#define CONFIG_CMD_HASH #define CONFIG_KEY_REVOCATION #ifndef CONFIG_SYS_RAMBOOT /* The key used for verification of next level images @@ -58,39 +78,55 @@ "setenv hwconfig \'fsl_ddr:ctlr_intlv=null,bank_intlv=null\';" #else #define CONFIG_EXTRA_ENV \ - "setenv fdt_high 0xcfffffff;" \ - "setenv initrd_high 0xcfffffff;" \ + "setenv fdt_high 0xffffffff;" \ + "setenv initrd_high 0xffffffff;" \ "setenv hwconfig \'fsl_ddr:ctlr_intlv=null,bank_intlv=null\';" #endif /* Copying Bootscript and Header to DDR from NOR for LS2 and for rest, from * Non-XIP Memory (Nand/SD)*/ -#if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_LS2080A) +#if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_LS2080A) || \ + defined(CONFIG_SD_BOOT) #define CONFIG_BOOTSCRIPT_COPY_RAM #endif -/* The address needs to be modified according to NOR and DDR memory map */ +/* The address needs to be modified according to NOR, NAND, SD and + * DDR memory map + */ #ifdef CONFIG_LS2080A -#define CONFIG_BS_HDR_ADDR_FLASH 0x583920000 -#define CONFIG_BS_ADDR_FLASH 0x583900000 +#define CONFIG_BS_HDR_ADDR_DEVICE 0x583920000 +#define CONFIG_BS_ADDR_DEVICE 0x583900000 #define CONFIG_BS_HDR_ADDR_RAM 0xa3920000 #define CONFIG_BS_ADDR_RAM 0xa3900000 +#define CONFIG_BS_HDR_SIZE 0x00002000 +#define CONFIG_BS_SIZE 0x00001000 +#else +#ifdef CONFIG_SD_BOOT +/* For SD boot address and size are assigned in terms of sector + * offset and no. of sectors respectively. + */ +#define CONFIG_BS_HDR_ADDR_DEVICE 0x00000800 +#define CONFIG_BS_ADDR_DEVICE 0x00000840 +#define CONFIG_BS_HDR_SIZE 0x00000010 +#define CONFIG_BS_SIZE 0x00000008 #else -#define CONFIG_BS_HDR_ADDR_FLASH 0x600a0000 -#define CONFIG_BS_ADDR_FLASH 0x60060000 -#define CONFIG_BS_HDR_ADDR_RAM 0xa0060000 -#define CONFIG_BS_ADDR_RAM 0xa0060000 +#define CONFIG_BS_HDR_ADDR_DEVICE 0x600a0000 +#define CONFIG_BS_ADDR_DEVICE 0x60060000 +#define CONFIG_BS_HDR_SIZE 0x00002000 +#define CONFIG_BS_SIZE 0x00001000 +#endif /* #ifdef CONFIG_SD_BOOT */ +#define CONFIG_BS_HDR_ADDR_RAM 0x81000000 +#define CONFIG_BS_ADDR_RAM 0x81020000 #endif #ifdef CONFIG_BOOTSCRIPT_COPY_RAM #define CONFIG_BOOTSCRIPT_HDR_ADDR CONFIG_BS_HDR_ADDR_RAM -#define CONFIG_BS_HDR_SIZE 0x00002000 #define CONFIG_BOOTSCRIPT_ADDR CONFIG_BS_ADDR_RAM -#define CONFIG_BS_SIZE 0x00001000 #else -#define CONFIG_BOOTSCRIPT_HDR_ADDR CONFIG_BS_HDR_ADDR_FLASH -/* BS_HDR_SIZE, BOOTSCRIPT_ADDR and BS_SIZE are not required */ +#define CONFIG_BOOTSCRIPT_HDR_ADDR CONFIG_BS_HDR_ADDR_DEVICE +/* BOOTSCRIPT_ADDR is not required */ #endif #include <config_fsl_chain_trust.h> +#endif /* #ifndef CONFIG_SPL_BUILD */ #endif /* #ifdef CONFIG_CHAIN_OF_TRUST */ #endif diff --git a/arch/arm/include/asm/psci.h b/arch/arm/include/asm/psci.h index e76ecb2..8aefaa7 100644 --- a/arch/arm/include/asm/psci.h +++ b/arch/arm/include/asm/psci.h @@ -31,6 +31,12 @@ #define ARM_PSCI_RET_NI (-1) #define ARM_PSCI_RET_INVAL (-2) #define ARM_PSCI_RET_DENIED (-3) +#define ARM_PSCI_RET_ALREADY_ON (-4) +#define ARM_PSCI_RET_ON_PENDING (-5) +#define ARM_PSCI_RET_INTERNAL_FAILURE (-6) +#define ARM_PSCI_RET_NOT_PRESENT (-7) +#define ARM_PSCI_RET_DISABLED (-8) +#define ARM_PSCI_RET_INVALID_ADDRESS (-9) /* PSCI 0.2 interface */ #define ARM_PSCI_0_2_FN_BASE 0x84000000 @@ -47,10 +53,25 @@ #define ARM_PSCI_0_2_FN_SYSTEM_OFF ARM_PSCI_0_2_FN(8) #define ARM_PSCI_0_2_FN_SYSTEM_RESET ARM_PSCI_0_2_FN(9) +/* PSCI 1.0 interface */ +#define ARM_PSCI_1_0_FN_PSCI_FEATURES ARM_PSCI_0_2_FN(10) +#define ARM_PSCI_1_0_FN_CPU_FREEZE ARM_PSCI_0_2_FN(11) +#define ARM_PSCI_1_0_FN_CPU_DEFAULT_SUSPEND ARM_PSCI_0_2_FN(12) +#define ARM_PSCI_1_0_FN_NODE_HW_STATE ARM_PSCI_0_2_FN(13) +#define ARM_PSCI_1_0_FN_SYSTEM_SUSPEND ARM_PSCI_0_2_FN(14) +#define ARM_PSCI_1_0_FN_SET_SUSPEND_MODE ARM_PSCI_0_2_FN(15) +#define ARM_PSCI_1_0_FN_STAT_RESIDENCY ARM_PSCI_0_2_FN(16) +#define ARM_PSCI_1_0_FN_STAT_COUNT ARM_PSCI_0_2_FN(17) + /* 1KB stack per core */ #define ARM_PSCI_STACK_SHIFT 10 #define ARM_PSCI_STACK_SIZE (1 << ARM_PSCI_STACK_SHIFT) +/* PSCI affinity level state returned by AFFINITY_INFO */ +#define PSCI_AFFINITY_LEVEL_ON 0 +#define PSCI_AFFINITY_LEVEL_OFF 1 +#define PSCI_AFFINITY_LEVEL_ON_PENDING 2 + #ifndef __ASSEMBLY__ #include <asm/types.h> diff --git a/arch/arm/mach-keystone/init.c b/arch/arm/mach-keystone/init.c index 3b6d5ef..6e5a1e1 100644 --- a/arch/arm/mach-keystone/init.c +++ b/arch/arm/mach-keystone/init.c @@ -101,9 +101,7 @@ static void msmc_k2hkle_common_setup(void) msmc_share_all_segments(KS2_MSMC_SEGMENT_C6X_0); msmc_share_all_segments(K2HKLE_MSMC_SEGMENT_ARM); msmc_share_all_segments(K2HKLE_MSMC_SEGMENT_NETCP); -#ifdef KS2_MSMC_SEGMENT_QM_PDSP msmc_share_all_segments(K2HKLE_MSMC_SEGMENT_QM_PDSP); -#endif msmc_share_all_segments(K2HKLE_MSMC_SEGMENT_PCIE0); msmc_share_all_segments(KS2_MSMC_SEGMENT_DEBUG); } diff --git a/arch/arm/mach-rockchip/Kconfig b/arch/arm/mach-rockchip/Kconfig index c49cc19..1aac3c8 100644 --- a/arch/arm/mach-rockchip/Kconfig +++ b/arch/arm/mach-rockchip/Kconfig @@ -1,7 +1,21 @@ if ARCH_ROCKCHIP +config ROCKCHIP_RK3036 + bool "Support Rockchip RK3036" + select CPU_V7 + select SUPPORT_SPL + select SPL + help + The Rockchip RK3036 is a ARM-based SoC with a dual-core Cortex-A7 + including NEON and GPU, Mali-400 graphics, several DDR3 options + and video codec support. Peripherals include Gigabit Ethernet, + USB2 host and OTG, SDIO, I2S, UART, SPI, I2C and PWMs. + config ROCKCHIP_RK3288 bool "Support Rockchip RK3288" + select CPU_V7 + select SUPPORT_SPL + select SPL help The Rockchip RK3288 is a ARM-based SoC with a quad-core Cortex-A17 including NEON and GPU, 1MB L2 cache, Mali-T7 graphics, two @@ -9,14 +23,26 @@ config ROCKCHIP_RK3288 and video codec support. Peripherals include Gigabit Ethernet, USB2 host and OTG, SDIO, I2S, UART,s, SPI, I2C and PWMs. -config ROCKCHIP_RK3036 - bool "Support Rockchip RK3036" +config ROCKCHIP_RK3399 + bool "Support Rockchip RK3399" + select ARM64 help - The Rockchip RK3036 is a ARM-based SoC with a dual-core Cortex-A7 - including NEON and GPU, Mali-400 graphics, several DDR3 options + The Rockchip RK3399 is a ARM-based SoC with a dual-core Cortex-A72 + and quad-core Cortex-A53. + including NEON and GPU, 1MB L2 cache, Mali-T7 graphics, two + video interfaces supporting HDMI and eDP, several DDR3 options and video codec support. Peripherals include Gigabit Ethernet, - USB2 host and OTG, SDIO, I2S, UART, SPI, I2C and PWMs. + USB2 host and OTG, SDIO, I2S, UARTs, SPI, I2C and PWMs. + +config ROCKCHIP_SPL_BACK_TO_BROM + bool "SPL returns to bootrom" + default y if ROCKCHIP_RK3036 + help + Rockchip SoCs have ability to load SPL & U-Boot binary. If enabled, + SPL will return to the boot rom, which will then load the U-Boot + binary to keep going on. -source "arch/arm/mach-rockchip/rk3288/Kconfig" source "arch/arm/mach-rockchip/rk3036/Kconfig" +source "arch/arm/mach-rockchip/rk3288/Kconfig" +source "arch/arm/mach-rockchip/rk3399/Kconfig" endif diff --git a/arch/arm/mach-rockchip/Makefile b/arch/arm/mach-rockchip/Makefile index 55567cb..157d42f 100644 --- a/arch/arm/mach-rockchip/Makefile +++ b/arch/arm/mach-rockchip/Makefile @@ -5,11 +5,15 @@ # ifdef CONFIG_SPL_BUILD -obj-$(CONFIG_ROCKCHIP_RK3288) += rk3288-board-spl.o obj-$(CONFIG_ROCKCHIP_RK3036) += rk3036-board-spl.o +obj-$(CONFIG_ROCKCHIP_RK3288) += rk3288-board-spl.o +obj-$(CONFIG_ROCKCHIP_SPL_BACK_TO_BROM) += save_boot_param.o else obj-$(CONFIG_ROCKCHIP_RK3288) += board.o endif +ifndef CONFIG_ARM64 obj-y += rk_timer.o -obj-$(CONFIG_ROCKCHIP_RK3288) += rk3288/ +endif obj-$(CONFIG_ROCKCHIP_RK3036) += rk3036/ +obj-$(CONFIG_ROCKCHIP_RK3288) += rk3288/ +obj-$(CONFIG_ROCKCHIP_RK3399) += rk3399/ diff --git a/arch/arm/mach-rockchip/board.c b/arch/arm/mach-rockchip/board.c index 816540e..bec756d 100644 --- a/arch/arm/mach-rockchip/board.c +++ b/arch/arm/mach-rockchip/board.c @@ -10,12 +10,45 @@ #include <ram.h> #include <asm/io.h> #include <asm/arch/clock.h> +#include <asm/arch/periph.h> +#include <asm/gpio.h> +#include <dm/pinctrl.h> DECLARE_GLOBAL_DATA_PTR; int board_init(void) { +#ifdef CONFIG_ROCKCHIP_SPL_BACK_TO_BROM + struct udevice *pinctrl; + int ret; + + /* + * We need to implement sdcard iomux here for the further + * initlization, otherwise, it'll hit sdcard command sending + * timeout exception. + */ + ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl); + if (ret) { + debug("%s: Cannot find pinctrl device\n", __func__); + goto err; + } + ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_SDCARD); + if (ret) { + debug("%s: Failed to set up SD card\n", __func__); + goto err; + } + + return 0; +err: + printf("board_init: Error %d\n", ret); + + /* No way to report error here */ + hang(); + + return -1; +#else return 0; +#endif } int dram_init(void) @@ -52,6 +85,78 @@ void lowlevel_init(void) { } +#if defined(CONFIG_USB_GADGET) && defined(CONFIG_USB_GADGET_DWC2_OTG) +#include <usb.h> +#include <usb/dwc2_udc.h> + +static struct dwc2_plat_otg_data rk3288_otg_data = { + .rx_fifo_sz = 512, + .np_tx_fifo_sz = 16, + .tx_fifo_sz = 128, +}; + +int board_usb_init(int index, enum usb_init_type init) +{ + int node, phy_node; + const char *mode; + bool matched = false; + const void *blob = gd->fdt_blob; + u32 grf_phy_offset; + + /* find the usb_otg node */ + node = fdt_node_offset_by_compatible(blob, -1, + "rockchip,rk3288-usb"); + + while (node > 0) { + mode = fdt_getprop(blob, node, "dr_mode", NULL); + if (mode && strcmp(mode, "otg") == 0) { + matched = true; + break; + } + + node = fdt_node_offset_by_compatible(blob, node, + "rockchip,rk3288-usb"); + } + if (!matched) { + debug("Not found usb_otg device\n"); + return -ENODEV; + } + rk3288_otg_data.regs_otg = fdtdec_get_addr(blob, node, "reg"); + + node = fdtdec_lookup_phandle(blob, node, "phys"); + if (node <= 0) { + debug("Not found usb phy device\n"); + return -ENODEV; + } + + phy_node = fdt_parent_offset(blob, node); + if (phy_node <= 0) { + debug("Not found usb phy device\n"); + return -ENODEV; + } + + rk3288_otg_data.phy_of_node = phy_node; + grf_phy_offset = fdtdec_get_addr(blob, node, "reg"); + + /* find the grf node */ + node = fdt_node_offset_by_compatible(blob, -1, + "rockchip,rk3288-grf"); + if (node <= 0) { + debug("Not found grf device\n"); + return -ENODEV; + } + rk3288_otg_data.regs_phy = grf_phy_offset + + fdtdec_get_addr(blob, node, "reg"); + + return dwc2_udc_probe(&rk3288_otg_data); +} + +int board_usb_cleanup(int index, enum usb_init_type init) +{ + return 0; +} +#endif + static int do_clock(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { @@ -73,7 +178,7 @@ static int do_clock(cmd_tbl_t *cmdtp, int flag, int argc, int ret, i; struct udevice *dev; - ret = uclass_get_device(UCLASS_CLK, 0, &dev); + ret = rockchip_get_clk(&dev); if (ret) { printf("clk-uclass not found\n"); return 0; diff --git a/arch/arm/mach-rockchip/rk3036/Kconfig b/arch/arm/mach-rockchip/rk3036/Kconfig index cc03808..f7562bd 100644 --- a/arch/arm/mach-rockchip/rk3036/Kconfig +++ b/arch/arm/mach-rockchip/rk3036/Kconfig @@ -15,7 +15,7 @@ config SYS_MALLOC_F_LEN config ROCKCHIP_COMMON bool "Support rk common fuction" -source "board/evb_rk3036/evb_rk3036/Kconfig" -source "board/kylin/kylin_rk3036/Kconfig" +source "board/rockchip/evb_rk3036/Kconfig" +source "board/rockchip/kylin_rk3036/Kconfig" endif diff --git a/arch/arm/mach-rockchip/rk3036/Makefile b/arch/arm/mach-rockchip/rk3036/Makefile index 97d299d..6095777 100644 --- a/arch/arm/mach-rockchip/rk3036/Makefile +++ b/arch/arm/mach-rockchip/rk3036/Makefile @@ -10,4 +10,3 @@ obj-y += syscon_rk3036.o endif obj-y += sdram_rk3036.o -obj-y += save_boot_param.o diff --git a/arch/arm/mach-rockchip/rk3288-board-spl.c b/arch/arm/mach-rockchip/rk3288-board-spl.c index 123f58b..ed14023 100644 --- a/arch/arm/mach-rockchip/rk3288-board-spl.c +++ b/arch/arm/mach-rockchip/rk3288-board-spl.c @@ -149,7 +149,7 @@ static int configure_emmc(struct udevice *pinctrl) return 0; } #endif - +extern void back_to_bootrom(void); void board_init_f(ulong dummy) { struct udevice *pinctrl; @@ -187,7 +187,7 @@ void board_init_f(ulong dummy) rockchip_timer_init(); configure_l2ctlr(); - ret = uclass_get_device(UCLASS_CLK, 0, &dev); + ret = rockchip_get_clk(&dev); if (ret) { debug("CLK init failed: %d\n", ret); return; @@ -204,6 +204,9 @@ void board_init_f(ulong dummy) debug("DRAM init failed: %d\n", ret); return; } +#ifdef CONFIG_ROCKCHIP_SPL_BACK_TO_BROM + back_to_bootrom(); +#endif } static int setup_led(void) @@ -248,7 +251,8 @@ void spl_board_init(void) } #ifdef CONFIG_SPL_MMC_SUPPORT if (!IS_ENABLED(CONFIG_TARGET_ROCK2) && - !IS_ENABLED(CONFIG_TARGET_FIREFLY_RK3288)) { + !IS_ENABLED(CONFIG_TARGET_FIREFLY_RK3288) && + !IS_ENABLED(CONFIG_TARGET_EVB_RK3288)) { ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_SDCARD); if (ret) { debug("%s: Failed to set up SD card\n", __func__); diff --git a/arch/arm/mach-rockchip/rk3288/Kconfig b/arch/arm/mach-rockchip/rk3288/Kconfig index 7215624..031dbfc 100644 --- a/arch/arm/mach-rockchip/rk3288/Kconfig +++ b/arch/arm/mach-rockchip/rk3288/Kconfig @@ -8,6 +8,14 @@ config TARGET_FIREFLY_RK3288 also includes on-board eMMC and 1GB of SDRAM. Expansion connectors provide access to display pins, I2C, SPI, UART and GPIOs. +config TARGET_EVB_RK3288 + bool "Evb-RK3288" + help + EVB-RK3288 is a RK3288-based development board with 2 USB ports, + HDMI, VGA, micro-SD card, audio, WiFi and Gigabit Ethernet, It + also includes on-board eMMC and 2GB of SDRAM. Expansion connectors + provide access to display pins, I2C, SPI, UART and GPIOs. + config TARGET_CHROMEBOOK_JERRY bool "Google/Rockchip Veyron-Jerry Chromebook" help @@ -45,4 +53,6 @@ source "board/firefly/firefly-rk3288/Kconfig" source "board/radxa/rock2/Kconfig" +source "board/evb-rk3288/evb-rk3288/Kconfig" + endif diff --git a/arch/arm/mach-rockchip/rk3288/Makefile b/arch/arm/mach-rockchip/rk3288/Makefile index 6f62375..82b00a1 100644 --- a/arch/arm/mach-rockchip/rk3288/Makefile +++ b/arch/arm/mach-rockchip/rk3288/Makefile @@ -4,6 +4,7 @@ # SPDX-License-Identifier: GPL-2.0+ # +obj-y += clk_rk3288.o obj-y += reset_rk3288.o obj-y += sdram_rk3288.o obj-y += syscon_rk3288.o diff --git a/arch/arm/mach-rockchip/rk3288/clk_rk3288.c b/arch/arm/mach-rockchip/rk3288/clk_rk3288.c new file mode 100644 index 0000000..2099e34 --- /dev/null +++ b/arch/arm/mach-rockchip/rk3288/clk_rk3288.c @@ -0,0 +1,17 @@ +/* + * Copyright (C) 2015 Google, Inc + * Written by Simon Glass <sjg@chromium.org> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <dm.h> +#include <syscon.h> +#include <asm/arch/clock.h> + +int rockchip_get_clk(struct udevice **devp) +{ + return uclass_get_device_by_driver(UCLASS_CLK, + DM_GET_DRIVER(rockchip_rk3288_cru), devp); +} diff --git a/arch/arm/mach-rockchip/rk3288/sdram_rk3288.c b/arch/arm/mach-rockchip/rk3288/sdram_rk3288.c index b36b6af..cf9ef2e 100644 --- a/arch/arm/mach-rockchip/rk3288/sdram_rk3288.c +++ b/arch/arm/mach-rockchip/rk3288/sdram_rk3288.c @@ -575,14 +575,14 @@ static void dram_all_config(const struct dram_info *dram, &sdram_params->ch[chan]; sys_reg |= info->row_3_4 << SYS_REG_ROW_3_4_SHIFT(chan); - sys_reg |= chan << SYS_REG_CHINFO_SHIFT(chan); + sys_reg |= 1 << SYS_REG_CHINFO_SHIFT(chan); sys_reg |= (info->rank - 1) << SYS_REG_RANK_SHIFT(chan); sys_reg |= (info->col - 9) << SYS_REG_COL_SHIFT(chan); - sys_reg |= info->bk == 3 ? 1 << SYS_REG_BK_SHIFT(chan) : 0; + sys_reg |= info->bk == 3 ? 0 : 1 << SYS_REG_BK_SHIFT(chan); sys_reg |= (info->cs0_row - 13) << SYS_REG_CS0_ROW_SHIFT(chan); sys_reg |= (info->cs1_row - 13) << SYS_REG_CS1_ROW_SHIFT(chan); - sys_reg |= info->bw << SYS_REG_BW_SHIFT(chan); - sys_reg |= info->dbw << SYS_REG_DBW_SHIFT(chan); + sys_reg |= (2 >> info->bw) << SYS_REG_BW_SHIFT(chan); + sys_reg |= (2 >> info->dbw) << SYS_REG_DBW_SHIFT(chan); dram_cfg_rbc(&dram->chan[chan], chan, sdram_params); } @@ -734,13 +734,13 @@ size_t sdram_size_mb(struct rk3288_pmu *pmu) rank = 1 + (sys_reg >> SYS_REG_RANK_SHIFT(ch) & SYS_REG_RANK_MASK); col = 9 + (sys_reg >> SYS_REG_COL_SHIFT(ch) & SYS_REG_COL_MASK); - bk = sys_reg & (1 << SYS_REG_BK_SHIFT(ch)) ? 3 : 0; + bk = 3 - ((sys_reg >> SYS_REG_BK_SHIFT(ch)) & SYS_REG_BK_MASK); cs0_row = 13 + (sys_reg >> SYS_REG_CS0_ROW_SHIFT(ch) & SYS_REG_CS0_ROW_MASK); cs1_row = 13 + (sys_reg >> SYS_REG_CS1_ROW_SHIFT(ch) & SYS_REG_CS1_ROW_MASK); - bw = (sys_reg >> SYS_REG_BW_SHIFT(ch)) & - SYS_REG_BW_MASK; + bw = (2 >> ((sys_reg >> SYS_REG_BW_SHIFT(ch)) & + SYS_REG_BW_MASK)); row_3_4 = sys_reg >> SYS_REG_ROW_3_4_SHIFT(ch) & SYS_REG_ROW_3_4_MASK; @@ -784,7 +784,7 @@ static int veyron_init(struct dram_info *priv) return ret; udelay(100);/* Must wait for voltage to stabilize, 2mV/us */ - rkclk_configure_cpu(priv->cru, priv->grf); + rk3288_clk_configure_cpu(priv->cru, priv->grf); return 0; } @@ -923,7 +923,7 @@ static int rk3288_dmc_probe(struct udevice *dev) priv->chan[1].pctl = regmap_get_range(plat->map, 2); priv->chan[1].publ = regmap_get_range(plat->map, 3); #endif - ret = uclass_get_device(UCLASS_CLK, 0, &dev_clk); + ret = rockchip_get_clk(&dev_clk); if (ret) return ret; priv->ddr_clk.id = CLK_DDR; diff --git a/arch/arm/mach-rockchip/rk3399/Kconfig b/arch/arm/mach-rockchip/rk3399/Kconfig new file mode 100644 index 0000000..83bd04a --- /dev/null +++ b/arch/arm/mach-rockchip/rk3399/Kconfig @@ -0,0 +1,23 @@ +if ROCKCHIP_RK3399 + +choice + prompt "RK3399 board select" + +config TARGET_EVB_RK3399 + bool "RK3399 evaluation board" + help + RK3399evb is a evaluation board for Rockchp rk3399, + with full function and phisical connectors support like type-C ports, + usb2.0 host ports, LVDS, JTAG, MAC, SDcard, HDMI, USB-2-serial... + +endchoice + +config SYS_SOC + default "rockchip" + +config SYS_MALLOC_F_LEN + default 0x0800 + +source "board/rockchip/evb_rk3399/Kconfig" + +endif diff --git a/arch/arm/mach-rockchip/rk3399/Makefile b/arch/arm/mach-rockchip/rk3399/Makefile new file mode 100644 index 0000000..3f219ac --- /dev/null +++ b/arch/arm/mach-rockchip/rk3399/Makefile @@ -0,0 +1,7 @@ +# +# (C) Copyright 2016 Rockchip Electronics Co., Ltd +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += rk3399.o diff --git a/arch/arm/mach-rockchip/rk3399/rk3399.c b/arch/arm/mach-rockchip/rk3399/rk3399.c new file mode 100644 index 0000000..b9d7629 --- /dev/null +++ b/arch/arm/mach-rockchip/rk3399/rk3399.c @@ -0,0 +1,30 @@ +/* + * Copyright (c) 2016 Rockchip Electronics Co., Ltd + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/armv8/mmu.h> + +static struct mm_region rk3399_mem_map[] = { + { + .virt = 0x0UL, + .phys = 0x0UL, + .size = 0x80000000UL, + .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) | + PTE_BLOCK_INNER_SHARE + }, { + .virt = 0xf0000000UL, + .phys = 0xf0000000UL, + .size = 0x10000000UL, + .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) | + PTE_BLOCK_NON_SHARE | + PTE_BLOCK_PXN | PTE_BLOCK_UXN + }, { + /* List terminator */ + 0, + } +}; + +struct mm_region *mem_map = rk3399_mem_map; diff --git a/arch/arm/mach-rockchip/rk3036/save_boot_param.S b/arch/arm/mach-rockchip/save_boot_param.S index 778ec83..85b407b 100644 --- a/arch/arm/mach-rockchip/rk3036/save_boot_param.S +++ b/arch/arm/mach-rockchip/save_boot_param.S @@ -1,5 +1,5 @@ /* - * (C) Copyright 2015 Google, Inc + * (C) Copyright 2016 Rockchip Electronics Co., Ltd * * SPDX-License-Identifier: GPL-2.0+ */ diff --git a/arch/powerpc/include/asm/fsl_secure_boot.h b/arch/powerpc/include/asm/fsl_secure_boot.h index 2e2d565..2e937f0 100644 --- a/arch/powerpc/include/asm/fsl_secure_boot.h +++ b/arch/powerpc/include/asm/fsl_secure_boot.h @@ -128,10 +128,10 @@ /* If Boot Script is not on NOR and is required to be copied on RAM */ #ifdef CONFIG_BOOTSCRIPT_COPY_RAM #define CONFIG_BS_HDR_ADDR_RAM 0x00010000 -#define CONFIG_BS_HDR_ADDR_FLASH 0x00800000 +#define CONFIG_BS_HDR_ADDR_DEVICE 0x00800000 #define CONFIG_BS_HDR_SIZE 0x00002000 #define CONFIG_BS_ADDR_RAM 0x00012000 -#define CONFIG_BS_ADDR_FLASH 0x00802000 +#define CONFIG_BS_ADDR_DEVICE 0x00802000 #define CONFIG_BS_SIZE 0x00001000 #define CONFIG_BOOTSCRIPT_HDR_ADDR CONFIG_BS_HDR_ADDR_RAM |