diff options
Diffstat (limited to 'arch/arm/cpu/armv7/omap-common')
| -rw-r--r-- | arch/arm/cpu/armv7/omap-common/Makefile | 13 | ||||
| -rw-r--r-- | arch/arm/cpu/armv7/omap-common/clocks-common.c | 609 | ||||
| -rw-r--r-- | arch/arm/cpu/armv7/omap-common/emif-common.c | 1140 | ||||
| -rw-r--r-- | arch/arm/cpu/armv7/omap-common/hwinit-common.c | 267 | ||||
| -rw-r--r-- | arch/arm/cpu/armv7/omap-common/lowlevel_init.S | 106 | ||||
| -rw-r--r-- | arch/arm/cpu/armv7/omap-common/mem-common.c | 45 | ||||
| -rw-r--r-- | arch/arm/cpu/armv7/omap-common/spl.c | 9 |
7 files changed, 2187 insertions, 2 deletions
diff --git a/arch/arm/cpu/armv7/omap-common/Makefile b/arch/arm/cpu/armv7/omap-common/Makefile index 1dee81f..a684611 100644 --- a/arch/arm/cpu/armv7/omap-common/Makefile +++ b/arch/arm/cpu/armv7/omap-common/Makefile @@ -33,6 +33,13 @@ ifdef CONFIG_OMAP COBJS += gpio.o endif +ifneq ($(CONFIG_OMAP44XX)$(CONFIG_OMAP54XX),) +COBJS += hwinit-common.o +COBJS += clocks-common.o +COBJS += emif-common.o +SOBJS += lowlevel_init.o +endif + ifdef CONFIG_SPL_BUILD COBJS += spl.o ifdef CONFIG_SPL_NAND_SUPPORT @@ -43,6 +50,12 @@ COBJS += spl_mmc.o endif endif +ifndef CONFIG_SPL_BUILD +ifneq ($(CONFIG_OMAP44XX)$(CONFIG_OMAP54XX),) +COBJS += mem-common.o +endif +endif + SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) diff --git a/arch/arm/cpu/armv7/omap-common/clocks-common.c b/arch/arm/cpu/armv7/omap-common/clocks-common.c new file mode 100644 index 0000000..f64a10b --- /dev/null +++ b/arch/arm/cpu/armv7/omap-common/clocks-common.c @@ -0,0 +1,609 @@ +/* + * + * Clock initialization for OMAP4 + * + * (C) Copyright 2010 + * Texas Instruments, <www.ti.com> + * + * Aneesh V <aneesh@ti.com> + * + * Based on previous work by: + * Santosh Shilimkar <santosh.shilimkar@ti.com> + * Rajendra Nayak <rnayak@ti.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include <common.h> +#include <asm/omap_common.h> +#include <asm/gpio.h> +#include <asm/arch/clocks.h> +#include <asm/arch/sys_proto.h> +#include <asm/utils.h> +#include <asm/omap_gpio.h> + +#ifndef CONFIG_SPL_BUILD +/* + * printing to console doesn't work unless + * this code is executed from SPL + */ +#define printf(fmt, args...) +#define puts(s) +#endif + +static inline u32 __get_sys_clk_index(void) +{ + u32 ind; + /* + * For ES1 the ROM code calibration of sys clock is not reliable + * due to hw issue. So, use hard-coded value. If this value is not + * correct for any board over-ride this function in board file + * From ES2.0 onwards you will get this information from + * CM_SYS_CLKSEL + */ + if (omap_revision() == OMAP4430_ES1_0) + ind = OMAP_SYS_CLK_IND_38_4_MHZ; + else { + /* SYS_CLKSEL - 1 to match the dpll param array indices */ + ind = (readl(&prcm->cm_sys_clksel) & + CM_SYS_CLKSEL_SYS_CLKSEL_MASK) - 1; + } + return ind; +} + +u32 get_sys_clk_index(void) + __attribute__ ((weak, alias("__get_sys_clk_index"))); + +u32 get_sys_clk_freq(void) +{ + u8 index = get_sys_clk_index(); + return sys_clk_array[index]; +} + +static inline void do_bypass_dpll(u32 *const base) +{ + struct dpll_regs *dpll_regs = (struct dpll_regs *)base; + + clrsetbits_le32(&dpll_regs->cm_clkmode_dpll, + CM_CLKMODE_DPLL_DPLL_EN_MASK, + DPLL_EN_FAST_RELOCK_BYPASS << + CM_CLKMODE_DPLL_EN_SHIFT); +} + +static inline void wait_for_bypass(u32 *const base) +{ + struct dpll_regs *const dpll_regs = (struct dpll_regs *)base; + + if (!wait_on_value(ST_DPLL_CLK_MASK, 0, &dpll_regs->cm_idlest_dpll, + LDELAY)) { + printf("Bypassing DPLL failed %p\n", base); + } +} + +static inline void do_lock_dpll(u32 *const base) +{ + struct dpll_regs *const dpll_regs = (struct dpll_regs *)base; + + clrsetbits_le32(&dpll_regs->cm_clkmode_dpll, + CM_CLKMODE_DPLL_DPLL_EN_MASK, + DPLL_EN_LOCK << CM_CLKMODE_DPLL_EN_SHIFT); +} + +static inline void wait_for_lock(u32 *const base) +{ + struct dpll_regs *const dpll_regs = (struct dpll_regs *)base; + + if (!wait_on_value(ST_DPLL_CLK_MASK, ST_DPLL_CLK_MASK, + &dpll_regs->cm_idlest_dpll, LDELAY)) { + printf("DPLL locking failed for %p\n", base); + hang(); + } +} + +inline u32 check_for_lock(u32 *const base) +{ + struct dpll_regs *const dpll_regs = (struct dpll_regs *)base; + u32 lock = readl(&dpll_regs->cm_idlest_dpll) & ST_DPLL_CLK_MASK; + + return lock; +} + +static void do_setup_dpll(u32 *const base, const struct dpll_params *params, + u8 lock, char *dpll) +{ + u32 temp, M, N; + struct dpll_regs *const dpll_regs = (struct dpll_regs *)base; + + temp = readl(&dpll_regs->cm_clksel_dpll); + + if (check_for_lock(base)) { + /* + * The Dpll has already been locked by rom code using CH. + * Check if M,N are matching with Ideal nominal opp values. + * If matches, skip the rest otherwise relock. + */ + M = (temp & CM_CLKSEL_DPLL_M_MASK) >> CM_CLKSEL_DPLL_M_SHIFT; + N = (temp & CM_CLKSEL_DPLL_N_MASK) >> CM_CLKSEL_DPLL_N_SHIFT; + if ((M != (params->m)) || (N != (params->n))) { + debug("\n %s Dpll locked, but not for ideal M = %d," + "N = %d values, current values are M = %d," + "N= %d" , dpll, params->m, params->n, + M, N); + } else { + /* Dpll locked with ideal values for nominal opps. */ + debug("\n %s Dpll already locked with ideal" + "nominal opp values", dpll); + goto setup_post_dividers; + } + } + + bypass_dpll(base); + + /* Set M & N */ + temp &= ~CM_CLKSEL_DPLL_M_MASK; + temp |= (params->m << CM_CLKSEL_DPLL_M_SHIFT) & CM_CLKSEL_DPLL_M_MASK; + + temp &= ~CM_CLKSEL_DPLL_N_MASK; + temp |= (params->n << CM_CLKSEL_DPLL_N_SHIFT) & CM_CLKSEL_DPLL_N_MASK; + + writel(temp, &dpll_regs->cm_clksel_dpll); + + /* Lock */ + if (lock) + do_lock_dpll(base); + +setup_post_dividers: + setup_post_dividers(base, params); + + /* Wait till the DPLL locks */ + if (lock) + wait_for_lock(base); +} + +u32 omap_ddr_clk(void) +{ + u32 ddr_clk, sys_clk_khz, omap_rev, divider; + const struct dpll_params *core_dpll_params; + + omap_rev = omap_revision(); + sys_clk_khz = get_sys_clk_freq() / 1000; + + core_dpll_params = get_core_dpll_params(); + + debug("sys_clk %d\n ", sys_clk_khz * 1000); + + /* Find Core DPLL locked frequency first */ + ddr_clk = sys_clk_khz * 2 * core_dpll_params->m / + (core_dpll_params->n + 1); + + if (omap_rev < OMAP5430_ES1_0) { + /* + * DDR frequency is PHY_ROOT_CLK/2 + * PHY_ROOT_CLK = Fdpll/2/M2 + */ + divider = 4; + } else { + /* + * DDR frequency is PHY_ROOT_CLK + * PHY_ROOT_CLK = Fdpll/2/M2 + */ + divider = 2; + } + + ddr_clk = ddr_clk / divider / core_dpll_params->m2; + ddr_clk *= 1000; /* convert to Hz */ + debug("ddr_clk %d\n ", ddr_clk); + + return ddr_clk; +} + +/* + * Lock MPU dpll + * + * Resulting MPU frequencies: + * 4430 ES1.0 : 600 MHz + * 4430 ES2.x : 792 MHz (OPP Turbo) + * 4460 : 920 MHz (OPP Turbo) - DCC disabled + */ +void configure_mpu_dpll(void) +{ + const struct dpll_params *params; + struct dpll_regs *mpu_dpll_regs; + u32 omap_rev; + omap_rev = omap_revision(); + + /* + * DCC and clock divider settings for 4460. + * DCC is required, if more than a certain frequency is required. + * For, 4460 > 1GHZ. + * 5430 > 1.4GHZ. + */ + if ((omap_rev >= OMAP4460_ES1_0) && (omap_rev < OMAP5430_ES1_0)) { + mpu_dpll_regs = + (struct dpll_regs *)&prcm->cm_clkmode_dpll_mpu; + bypass_dpll(&prcm->cm_clkmode_dpll_mpu); + clrbits_le32(&prcm->cm_mpu_mpu_clkctrl, + MPU_CLKCTRL_CLKSEL_EMIF_DIV_MODE_MASK); + setbits_le32(&prcm->cm_mpu_mpu_clkctrl, + MPU_CLKCTRL_CLKSEL_ABE_DIV_MODE_MASK); + clrbits_le32(&mpu_dpll_regs->cm_clksel_dpll, + CM_CLKSEL_DCC_EN_MASK); + } + + params = get_mpu_dpll_params(); + + do_setup_dpll(&prcm->cm_clkmode_dpll_mpu, params, DPLL_LOCK, "mpu"); + debug("MPU DPLL locked\n"); +} + +static void setup_dplls(void) +{ + u32 sysclk_ind, temp; + const struct dpll_params *params; + debug("setup_dplls\n"); + + sysclk_ind = get_sys_clk_index(); + + /* CORE dpll */ + params = get_core_dpll_params(); /* default - safest */ + /* + * Do not lock the core DPLL now. Just set it up. + * Core DPLL will be locked after setting up EMIF + * using the FREQ_UPDATE method(freq_update_core()) + */ + do_setup_dpll(&prcm->cm_clkmode_dpll_core, params, DPLL_NO_LOCK, + "core"); + /* Set the ratios for CORE_CLK, L3_CLK, L4_CLK */ + temp = (CLKSEL_CORE_X2_DIV_1 << CLKSEL_CORE_SHIFT) | + (CLKSEL_L3_CORE_DIV_2 << CLKSEL_L3_SHIFT) | + (CLKSEL_L4_L3_DIV_2 << CLKSEL_L4_SHIFT); + writel(temp, &prcm->cm_clksel_core); + debug("Core DPLL configured\n"); + + /* lock PER dpll */ + params = get_per_dpll_params(); + do_setup_dpll(&prcm->cm_clkmode_dpll_per, + params, DPLL_LOCK, "per"); + debug("PER DPLL locked\n"); + + /* MPU dpll */ + configure_mpu_dpll(); +} + +#ifdef CONFIG_SYS_CLOCKS_ENABLE_ALL +static void setup_non_essential_dplls(void) +{ + u32 sys_clk_khz, abe_ref_clk; + u32 sysclk_ind, sd_div, num, den; + const struct dpll_params *params; + + sysclk_ind = get_sys_clk_index(); + sys_clk_khz = get_sys_clk_freq() / 1000; + + /* IVA */ + clrsetbits_le32(&prcm->cm_bypclk_dpll_iva, + CM_BYPCLK_DPLL_IVA_CLKSEL_MASK, DPLL_IVA_CLKSEL_CORE_X2_DIV_2); + + params = get_iva_dpll_params(); + do_setup_dpll(&prcm->cm_clkmode_dpll_iva, params, DPLL_LOCK, "iva"); + + /* + * USB: + * USB dpll is J-type. Need to set DPLL_SD_DIV for jitter correction + * DPLL_SD_DIV = CEILING ([DPLL_MULT/(DPLL_DIV+1)]* CLKINP / 250) + * - where CLKINP is sys_clk in MHz + * Use CLKINP in KHz and adjust the denominator accordingly so + * that we have enough accuracy and at the same time no overflow + */ + params = get_usb_dpll_params(); + num = params->m * sys_clk_khz; + den = (params->n + 1) * 250 * 1000; + num += den - 1; + sd_div = num / den; + clrsetbits_le32(&prcm->cm_clksel_dpll_usb, + CM_CLKSEL_DPLL_DPLL_SD_DIV_MASK, + sd_div << CM_CLKSEL_DPLL_DPLL_SD_DIV_SHIFT); + + /* Now setup the dpll with the regular function */ + do_setup_dpll(&prcm->cm_clkmode_dpll_usb, params, DPLL_LOCK, "usb"); + + /* Configure ABE dpll */ + params = get_abe_dpll_params(); +#ifdef CONFIG_SYS_OMAP_ABE_SYSCK + abe_ref_clk = CM_ABE_PLL_REF_CLKSEL_CLKSEL_SYSCLK; +#else + abe_ref_clk = CM_ABE_PLL_REF_CLKSEL_CLKSEL_32KCLK; + /* + * We need to enable some additional options to achieve + * 196.608MHz from 32768 Hz + */ + setbits_le32(&prcm->cm_clkmode_dpll_abe, + CM_CLKMODE_DPLL_DRIFTGUARD_EN_MASK| + CM_CLKMODE_DPLL_RELOCK_RAMP_EN_MASK| + CM_CLKMODE_DPLL_LPMODE_EN_MASK| + CM_CLKMODE_DPLL_REGM4XEN_MASK); + /* Spend 4 REFCLK cycles at each stage */ + clrsetbits_le32(&prcm->cm_clkmode_dpll_abe, + CM_CLKMODE_DPLL_RAMP_RATE_MASK, + 1 << CM_CLKMODE_DPLL_RAMP_RATE_SHIFT); +#endif + + /* Select the right reference clk */ + clrsetbits_le32(&prcm->cm_abe_pll_ref_clksel, + CM_ABE_PLL_REF_CLKSEL_CLKSEL_MASK, + abe_ref_clk << CM_ABE_PLL_REF_CLKSEL_CLKSEL_SHIFT); + /* Lock the dpll */ + do_setup_dpll(&prcm->cm_clkmode_dpll_abe, params, DPLL_LOCK, "abe"); +} +#endif + +void do_scale_tps62361(u32 reg, u32 volt_mv) +{ + u32 temp, step; + + step = volt_mv - TPS62361_BASE_VOLT_MV; + step /= 10; + + /* + * Select SET1 in TPS62361: + * VSEL1 is grounded on board. So the following selects + * VSEL1 = 0 and VSEL0 = 1 + */ + gpio_direction_output(TPS62361_VSEL0_GPIO, 0); + gpio_set_value(TPS62361_VSEL0_GPIO, 1); + + temp = TPS62361_I2C_SLAVE_ADDR | + (reg << PRM_VC_VAL_BYPASS_REGADDR_SHIFT) | + (step << PRM_VC_VAL_BYPASS_DATA_SHIFT) | + PRM_VC_VAL_BYPASS_VALID_BIT; + debug("do_scale_tps62361: volt - %d step - 0x%x\n", volt_mv, step); + + writel(temp, &prcm->prm_vc_val_bypass); + if (!wait_on_value(PRM_VC_VAL_BYPASS_VALID_BIT, 0, + &prcm->prm_vc_val_bypass, LDELAY)) { + puts("Scaling voltage failed for vdd_mpu from TPS\n"); + } +} + +void do_scale_vcore(u32 vcore_reg, u32 volt_mv) +{ + u32 temp, offset_code; + u32 step = 12660; /* 12.66 mV represented in uV */ + u32 offset = volt_mv; + + /* convert to uV for better accuracy in the calculations */ + offset *= 1000; + + if (omap_revision() == OMAP4430_ES1_0) + offset -= PHOENIX_SMPS_BASE_VOLT_STD_MODE_UV; + else + offset -= PHOENIX_SMPS_BASE_VOLT_STD_MODE_WITH_OFFSET_UV; + + offset_code = (offset + step - 1) / step; + /* The code starts at 1 not 0 */ + offset_code++; + + debug("do_scale_vcore: volt - %d offset_code - 0x%x\n", volt_mv, + offset_code); + + temp = SMPS_I2C_SLAVE_ADDR | + (vcore_reg << PRM_VC_VAL_BYPASS_REGADDR_SHIFT) | + (offset_code << PRM_VC_VAL_BYPASS_DATA_SHIFT) | + PRM_VC_VAL_BYPASS_VALID_BIT; + writel(temp, &prcm->prm_vc_val_bypass); + if (!wait_on_value(PRM_VC_VAL_BYPASS_VALID_BIT, 0, + &prcm->prm_vc_val_bypass, LDELAY)) { + printf("Scaling voltage failed for 0x%x\n", vcore_reg); + } +} + +static inline void enable_clock_domain(u32 *const clkctrl_reg, u32 enable_mode) +{ + clrsetbits_le32(clkctrl_reg, CD_CLKCTRL_CLKTRCTRL_MASK, + enable_mode << CD_CLKCTRL_CLKTRCTRL_SHIFT); + debug("Enable clock domain - %p\n", clkctrl_reg); +} + +static inline void wait_for_clk_enable(u32 *clkctrl_addr) +{ + u32 clkctrl, idlest = MODULE_CLKCTRL_IDLEST_DISABLED; + u32 bound = LDELAY; + + while ((idlest == MODULE_CLKCTRL_IDLEST_DISABLED) || + (idlest == MODULE_CLKCTRL_IDLEST_TRANSITIONING)) { + + clkctrl = readl(clkctrl_addr); + idlest = (clkctrl & MODULE_CLKCTRL_IDLEST_MASK) >> + MODULE_CLKCTRL_IDLEST_SHIFT; + if (--bound == 0) { + printf("Clock enable failed for 0x%p idlest 0x%x\n", + clkctrl_addr, clkctrl); + return; + } + } +} + +static inline void enable_clock_module(u32 *const clkctrl_addr, u32 enable_mode, + u32 wait_for_enable) +{ + clrsetbits_le32(clkctrl_addr, MODULE_CLKCTRL_MODULEMODE_MASK, + enable_mode << MODULE_CLKCTRL_MODULEMODE_SHIFT); + debug("Enable clock module - %p\n", clkctrl_addr); + if (wait_for_enable) + wait_for_clk_enable(clkctrl_addr); +} + +void freq_update_core(void) +{ + u32 freq_config1 = 0; + const struct dpll_params *core_dpll_params; + + core_dpll_params = get_core_dpll_params(); + /* Put EMIF clock domain in sw wakeup mode */ + enable_clock_domain(&prcm->cm_memif_clkstctrl, + CD_CLKCTRL_CLKTRCTRL_SW_WKUP); + wait_for_clk_enable(&prcm->cm_memif_emif_1_clkctrl); + wait_for_clk_enable(&prcm->cm_memif_emif_2_clkctrl); + + freq_config1 = SHADOW_FREQ_CONFIG1_FREQ_UPDATE_MASK | + SHADOW_FREQ_CONFIG1_DLL_RESET_MASK; + + freq_config1 |= (DPLL_EN_LOCK << SHADOW_FREQ_CONFIG1_DPLL_EN_SHIFT) & + SHADOW_FREQ_CONFIG1_DPLL_EN_MASK; + + freq_config1 |= (core_dpll_params->m2 << + SHADOW_FREQ_CONFIG1_M2_DIV_SHIFT) & + SHADOW_FREQ_CONFIG1_M2_DIV_MASK; + + writel(freq_config1, &prcm->cm_shadow_freq_config1); + if (!wait_on_value(SHADOW_FREQ_CONFIG1_FREQ_UPDATE_MASK, 0, + &prcm->cm_shadow_freq_config1, LDELAY)) { + puts("FREQ UPDATE procedure failed!!"); + hang(); + } + + /* Put EMIF clock domain back in hw auto mode */ + enable_clock_domain(&prcm->cm_memif_clkstctrl, + CD_CLKCTRL_CLKTRCTRL_HW_AUTO); + wait_for_clk_enable(&prcm->cm_memif_emif_1_clkctrl); + wait_for_clk_enable(&prcm->cm_memif_emif_2_clkctrl); +} + +void bypass_dpll(u32 *const base) +{ + do_bypass_dpll(base); + wait_for_bypass(base); +} + +void lock_dpll(u32 *const base) +{ + do_lock_dpll(base); + wait_for_lock(base); +} + +void setup_clocks_for_console(void) +{ + /* Do not add any spl_debug prints in this function */ + clrsetbits_le32(&prcm->cm_l4per_clkstctrl, CD_CLKCTRL_CLKTRCTRL_MASK, + CD_CLKCTRL_CLKTRCTRL_SW_WKUP << + CD_CLKCTRL_CLKTRCTRL_SHIFT); + + /* Enable all UARTs - console will be on one of them */ + clrsetbits_le32(&prcm->cm_l4per_uart1_clkctrl, + MODULE_CLKCTRL_MODULEMODE_MASK, + MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN << + MODULE_CLKCTRL_MODULEMODE_SHIFT); + + clrsetbits_le32(&prcm->cm_l4per_uart2_clkctrl, + MODULE_CLKCTRL_MODULEMODE_MASK, + MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN << + MODULE_CLKCTRL_MODULEMODE_SHIFT); + + clrsetbits_le32(&prcm->cm_l4per_uart3_clkctrl, + MODULE_CLKCTRL_MODULEMODE_MASK, + MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN << + MODULE_CLKCTRL_MODULEMODE_SHIFT); + + clrsetbits_le32(&prcm->cm_l4per_uart3_clkctrl, + MODULE_CLKCTRL_MODULEMODE_MASK, + MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN << + MODULE_CLKCTRL_MODULEMODE_SHIFT); + + clrsetbits_le32(&prcm->cm_l4per_clkstctrl, CD_CLKCTRL_CLKTRCTRL_MASK, + CD_CLKCTRL_CLKTRCTRL_HW_AUTO << + CD_CLKCTRL_CLKTRCTRL_SHIFT); +} + +void setup_sri2c(void) +{ + u32 sys_clk_khz, cycles_hi, cycles_low, temp; + + sys_clk_khz = get_sys_clk_freq() / 1000; + + /* + * Setup the dedicated I2C controller for Voltage Control + * I2C clk - high period 40% low period 60% + */ + cycles_hi = sys_clk_khz * 4 / PRM_VC_I2C_CHANNEL_FREQ_KHZ / 10; + cycles_low = sys_clk_khz * 6 / PRM_VC_I2C_CHANNEL_FREQ_KHZ / 10; + /* values to be set in register - less by 5 & 7 respectively */ + cycles_hi -= 5; + cycles_low -= 7; + temp = (cycles_hi << PRM_VC_CFG_I2C_CLK_SCLH_SHIFT) | + (cycles_low << PRM_VC_CFG_I2C_CLK_SCLL_SHIFT); + writel(temp, &prcm->prm_vc_cfg_i2c_clk); + + /* Disable high speed mode and all advanced features */ + writel(0x0, &prcm->prm_vc_cfg_i2c_mode); +} + +void do_enable_clocks(u32 *const *clk_domains, + u32 *const *clk_modules_hw_auto, + u32 *const *clk_modules_explicit_en, + u8 wait_for_enable) +{ + u32 i, max = 100; + + /* Put the clock domains in SW_WKUP mode */ + for (i = 0; (i < max) && clk_domains[i]; i++) { + enable_clock_domain(clk_domains[i], + CD_CLKCTRL_CLKTRCTRL_SW_WKUP); + } + + /* Clock modules that need to be put in HW_AUTO */ + for (i = 0; (i < max) && clk_modules_hw_auto[i]; i++) { + enable_clock_module(clk_modules_hw_auto[i], + MODULE_CLKCTRL_MODULEMODE_HW_AUTO, + wait_for_enable); + }; + + /* Clock modules that need to be put in SW_EXPLICIT_EN mode */ + for (i = 0; (i < max) && clk_modules_explicit_en[i]; i++) { + enable_clock_module(clk_modules_explicit_en[i], + MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN, + wait_for_enable); + }; + + /* Put the clock domains in HW_AUTO mode now */ + for (i = 0; (i < max) && clk_domains[i]; i++) { + enable_clock_domain(clk_domains[i], + CD_CLKCTRL_CLKTRCTRL_HW_AUTO); + } +} + +void prcm_init(void) +{ + switch (omap_hw_init_context()) { + case OMAP_INIT_CONTEXT_SPL: + case OMAP_INIT_CONTEXT_UBOOT_FROM_NOR: + case OMAP_INIT_CONTEXT_UBOOT_AFTER_CH: + enable_basic_clocks(); + scale_vcores(); + setup_dplls(); +#ifdef CONFIG_SYS_CLOCKS_ENABLE_ALL + setup_non_essential_dplls(); + enable_non_essential_clocks(); +#endif + break; + default: + break; + } + + if (OMAP_INIT_CONTEXT_SPL != omap_hw_init_context()) + enable_basic_uboot_clocks(); +} diff --git a/arch/arm/cpu/armv7/omap-common/emif-common.c b/arch/arm/cpu/armv7/omap-common/emif-common.c new file mode 100644 index 0000000..ce03b5c --- /dev/null +++ b/arch/arm/cpu/armv7/omap-common/emif-common.c @@ -0,0 +1,1140 @@ +/* + * EMIF programming + * + * (C) Copyright 2010 + * Texas Instruments, <www.ti.com> + * + * Aneesh V <aneesh@ti.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/emif.h> +#include <asm/arch/clocks.h> +#include <asm/arch/sys_proto.h> +#include <asm/omap_common.h> +#include <asm/utils.h> + +inline u32 emif_num(u32 base) +{ + if (base == EMIF1_BASE) + return 1; + else if (base == EMIF2_BASE) + return 2; + else + return 0; +} + + +static inline u32 get_mr(u32 base, u32 cs, u32 mr_addr) +{ + u32 mr; + struct emif_reg_struct *emif = (struct emif_reg_struct *)base; + + mr_addr |= cs << EMIF_REG_CS_SHIFT; + writel(mr_addr, &emif->emif_lpddr2_mode_reg_cfg); + if (omap_revision() == OMAP4430_ES2_0) + mr = readl(&emif->emif_lpddr2_mode_reg_data_es2); + else + mr = readl(&emif->emif_lpddr2_mode_reg_data); + debug("get_mr: EMIF%d cs %d mr %08x val 0x%x\n", emif_num(base), + cs, mr_addr, mr); + return mr; +} + +static inline void set_mr(u32 base, u32 cs, u32 mr_addr, u32 mr_val) +{ + struct emif_reg_struct *emif = (struct emif_reg_struct *)base; + + mr_addr |= cs << EMIF_REG_CS_SHIFT; + writel(mr_addr, &emif->emif_lpddr2_mode_reg_cfg); + writel(mr_val, &emif->emif_lpddr2_mode_reg_data); +} + +void emif_reset_phy(u32 base) +{ + struct emif_reg_struct *emif = (struct emif_reg_struct *)base; + u32 iodft; + + iodft = readl(&emif->emif_iodft_tlgc); + iodft |= EMIF_REG_RESET_PHY_MASK; + writel(iodft, &emif->emif_iodft_tlgc); +} + +static void do_lpddr2_init(u32 base, u32 cs) +{ + u32 mr_addr; + + /* Wait till device auto initialization is complete */ + while (get_mr(base, cs, LPDDR2_MR0) & LPDDR2_MR0_DAI_MASK) + ; + set_mr(base, cs, LPDDR2_MR10, MR10_ZQ_ZQINIT); + /* + * tZQINIT = 1 us + * Enough loops assuming a maximum of 2GHz + */ + sdelay(2000); + set_mr(base, cs, LPDDR2_MR1, MR1_BL_8_BT_SEQ_WRAP_EN_NWR_3); + set_mr(base, cs, LPDDR2_MR16, MR16_REF_FULL_ARRAY); + /* + * Enable refresh along with writing MR2 + * Encoding of RL in MR2 is (RL - 2) + */ + mr_addr = LPDDR2_MR2 | EMIF_REG_REFRESH_EN_MASK; + set_mr(base, cs, mr_addr, RL_FINAL - 2); +} + +static void lpddr2_init(u32 base, const struct emif_regs *regs) +{ + struct emif_reg_struct *emif = (struct emif_reg_struct *)base; + + /* Not NVM */ + clrbits_le32(&emif->emif_lpddr2_nvm_config, EMIF_REG_CS1NVMEN_MASK); + + /* + * Keep REG_INITREF_DIS = 1 to prevent re-initialization of SDRAM + * when EMIF_SDRAM_CONFIG register is written + */ + setbits_le32(&emif->emif_sdram_ref_ctrl, EMIF_REG_INITREF_DIS_MASK); + + /* + * Set the SDRAM_CONFIG and PHY_CTRL for the + * un-locked frequency & default RL + */ + writel(regs->sdram_config_init, &emif->emif_sdram_config); + writel(regs->emif_ddr_phy_ctlr_1_init, &emif->emif_ddr_phy_ctrl_1); + + do_lpddr2_init(base, CS0); + if (regs->sdram_config & EMIF_REG_EBANK_MASK) + do_lpddr2_init(base, CS1); + + writel(regs->sdram_config, &emif->emif_sdram_config); + writel(regs->emif_ddr_phy_ctlr_1, &emif->emif_ddr_phy_ctrl_1); + + /* Enable refresh now */ + clrbits_le32(&emif->emif_sdram_ref_ctrl, EMIF_REG_INITREF_DIS_MASK); + +} + +void emif_update_timings(u32 base, const struct emif_regs *regs) +{ + struct emif_reg_struct *emif = (struct emif_reg_struct *)base; + + writel(regs->ref_ctrl, &emif->emif_sdram_ref_ctrl_shdw); + writel(regs->sdram_tim1, &emif->emif_sdram_tim_1_shdw); + writel(regs->sdram_tim2, &emif->emif_sdram_tim_2_shdw); + writel(regs->sdram_tim3, &emif->emif_sdram_tim_3_shdw); + if (omap_revision() == OMAP4430_ES1_0) { + /* ES1 bug EMIF should be in force idle during freq_update */ + writel(0, &emif->emif_pwr_mgmt_ctrl); + } else { + writel(EMIF_PWR_MGMT_CTRL, &emif->emif_pwr_mgmt_ctrl); + writel(EMIF_PWR_MGMT_CTRL_SHDW, &emif->emif_pwr_mgmt_ctrl_shdw); + } + writel(regs->read_idle_ctrl, &emif->emif_read_idlectrl_shdw); + writel(regs->zq_config, &emif->emif_zq_config); + writel(regs->temp_alert_config, &emif->emif_temp_alert_config); + writel(regs->emif_ddr_phy_ctlr_1, &emif->emif_ddr_phy_ctrl_1_shdw); + + if (omap_revision() == OMAP5430_ES1_0) { + writel(EMIF_L3_CONFIG_VAL_SYS_10_MPU_5_LL_0, + &emif->emif_l3_config); + } else if (omap_revision() >= OMAP4460_ES1_0) { + writel(EMIF_L3_CONFIG_VAL_SYS_10_MPU_3_LL_0, + &emif->emif_l3_config); + } else { + writel(EMIF_L3_CONFIG_VAL_SYS_10_LL_0, + &emif->emif_l3_config); + } +} + +#ifndef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS +#define print_timing_reg(reg) debug(#reg" - 0x%08x\n", (reg)) + +/* + * Organization and refresh requirements for LPDDR2 devices of different + * types and densities. Derived from JESD209-2 section 2.4 + */ +const struct lpddr2_addressing addressing_table[] = { + /* Banks tREFIx10 rowx32,rowx16 colx32,colx16 density */ + {BANKS4, T_REFI_15_6, {ROW_12, ROW_12}, {COL_7, COL_8} },/*64M */ + {BANKS4, T_REFI_15_6, {ROW_12, ROW_12}, {COL_8, COL_9} },/*128M */ + {BANKS4, T_REFI_7_8, {ROW_13, ROW_13}, {COL_8, COL_9} },/*256M */ + {BANKS4, T_REFI_7_8, {ROW_13, ROW_13}, {COL_9, COL_10} },/*512M */ + {BANKS8, T_REFI_7_8, {ROW_13, ROW_13}, {COL_9, COL_10} },/*1GS4 */ + {BANKS8, T_REFI_3_9, {ROW_14, ROW_14}, {COL_9, COL_10} },/*2GS4 */ + {BANKS8, T_REFI_3_9, {ROW_14, ROW_14}, {COL_10, COL_11} },/*4G */ + {BANKS8, T_REFI_3_9, {ROW_15, ROW_15}, {COL_10, COL_11} },/*8G */ + {BANKS4, T_REFI_7_8, {ROW_14, ROW_14}, {COL_9, COL_10} },/*1GS2 */ + {BANKS4, T_REFI_3_9, {ROW_15, ROW_15}, {COL_9, COL_10} },/*2GS2 */ +}; + +static const u32 lpddr2_density_2_size_in_mbytes[] = { + 8, /* 64Mb */ + 16, /* 128Mb */ + 32, /* 256Mb */ + 64, /* 512Mb */ + 128, /* 1Gb */ + 256, /* 2Gb */ + 512, /* 4Gb */ + 1024, /* 8Gb */ + 2048, /* 16Gb */ + 4096 /* 32Gb */ +}; + +/* + * Calculate the period of DDR clock from frequency value and set the + * denominator and numerator in global variables for easy access later + */ +static void set_ddr_clk_period(u32 freq) +{ + /* + * period = 1/freq + * period_in_ns = 10^9/freq + */ + *T_num = 1000000000; + *T_den = freq; + cancel_out(T_num, T_den, 200); + +} + +/* + * Convert time in nano seconds to number of cycles of DDR clock + */ +static inline u32 ns_2_cycles(u32 ns) +{ + return ((ns * (*T_den)) + (*T_num) - 1) / (*T_num); +} + +/* + * ns_2_cycles with the difference that the time passed is 2 times the actual + * value(to avoid fractions). The cycles returned is for the original value of + * the timing parameter + */ +static inline u32 ns_x2_2_cycles(u32 ns) +{ + return ((ns * (*T_den)) + (*T_num) * 2 - 1) / ((*T_num) * 2); +} + +/* + * Find addressing table index based on the device's type(S2 or S4) and + * density + */ +s8 addressing_table_index(u8 type, u8 density, u8 width) +{ + u8 index; + if ((density > LPDDR2_DENSITY_8Gb) || (width == LPDDR2_IO_WIDTH_8)) + return -1; + + /* + * Look at the way ADDR_TABLE_INDEX* values have been defined + * in emif.h compared to LPDDR2_DENSITY_* values + * The table is layed out in the increasing order of density + * (ignoring type). The exceptions 1GS2 and 2GS2 have been placed + * at the end + */ + if ((type == LPDDR2_TYPE_S2) && (density == LPDDR2_DENSITY_1Gb)) + index = ADDR_TABLE_INDEX1GS2; + else if ((type == LPDDR2_TYPE_S2) && (density == LPDDR2_DENSITY_2Gb)) + index = ADDR_TABLE_INDEX2GS2; + else + index = density; + + debug("emif: addressing table index %d\n", index); + + return index; +} + +/* + * Find the the right timing table from the array of timing + * tables of the device using DDR clock frequency + */ +static const struct lpddr2_ac_timings *get_timings_table(const struct + lpddr2_ac_timings const *const *device_timings, + u32 freq) +{ + u32 i, temp, freq_nearest; + const struct lpddr2_ac_timings *timings = 0; + + emif_assert(freq <= MAX_LPDDR2_FREQ); + emif_assert(device_timings); + + /* + * Start with the maximum allowed frequency - that is always safe + */ + freq_nearest = MAX_LPDDR2_FREQ; + /* + * Find the timings table that has the max frequency value: + * i. Above or equal to the DDR frequency - safe + * ii. The lowest that satisfies condition (i) - optimal + */ + for (i = 0; (i < MAX_NUM_SPEEDBINS) && device_timings[i]; i++) { + temp = device_timings[i]->max_freq; + if ((temp >= freq) && (temp <= freq_nearest)) { + freq_nearest = temp; + timings = device_timings[i]; + } + } + debug("emif: timings table: %d\n", freq_nearest); + return timings; +} + +/* + * Finds the value of emif_sdram_config_reg + * All parameters are programmed based on the device on CS0. + * If there is a device on CS1, it will be same as that on CS0 or + * it will be NVM. We don't support NVM yet. + * If cs1_device pointer is NULL it is assumed that there is no device + * on CS1 + */ +static u32 get_sdram_config_reg(const struct lpddr2_device_details *cs0_device, + const struct lpddr2_device_details *cs1_device, + const struct lpddr2_addressing *addressing, + u8 RL) +{ + u32 config_reg = 0; + + config_reg |= (cs0_device->type + 4) << EMIF_REG_SDRAM_TYPE_SHIFT; + config_reg |= EMIF_INTERLEAVING_POLICY_MAX_INTERLEAVING << + EMIF_REG_IBANK_POS_SHIFT; + + config_reg |= cs0_device->io_width << EMIF_REG_NARROW_MODE_SHIFT; + + config_reg |= RL << EMIF_REG_CL_SHIFT; + + config_reg |= addressing->row_sz[cs0_device->io_width] << + EMIF_REG_ROWSIZE_SHIFT; + + config_reg |= addressing->num_banks << EMIF_REG_IBANK_SHIFT; + + config_reg |= (cs1_device ? EBANK_CS1_EN : EBANK_CS1_DIS) << + EMIF_REG_EBANK_SHIFT; + + config_reg |= addressing->col_sz[cs0_device->io_width] << + EMIF_REG_PAGESIZE_SHIFT; + + return config_reg; +} + +static u32 get_sdram_ref_ctrl(u32 freq, + const struct lpddr2_addressing *addressing) +{ + u32 ref_ctrl = 0, val = 0, freq_khz; + freq_khz = freq / 1000; + /* + * refresh rate to be set is 'tREFI * freq in MHz + * division by 10000 to account for khz and x10 in t_REFI_us_x10 + */ + val = addressing->t_REFI_us_x10 * freq_khz / 10000; + ref_ctrl |= val << EMIF_REG_REFRESH_RATE_SHIFT; + + return ref_ctrl; +} + +static u32 get_sdram_tim_1_reg(const struct lpddr2_ac_timings *timings, + const struct lpddr2_min_tck *min_tck, + const struct lpddr2_addressing *addressing) +{ + u32 tim1 = 0, val = 0; + val = max(min_tck->tWTR, ns_x2_2_cycles(timings->tWTRx2)) - 1; + tim1 |= val << EMIF_REG_T_WTR_SHIFT; + + if (addressing->num_banks == BANKS8) + val = (timings->tFAW * (*T_den) + 4 * (*T_num) - 1) / + (4 * (*T_num)) - 1; + else + val = max(min_tck->tRRD, ns_2_cycles(timings->tRRD)) - 1; + + tim1 |= val << EMIF_REG_T_RRD_SHIFT; + + val = ns_2_cycles(timings->tRASmin + timings->tRPab) - 1; + tim1 |= val << EMIF_REG_T_RC_SHIFT; + + val = max(min_tck->tRAS_MIN, ns_2_cycles(timings->tRASmin)) - 1; + tim1 |= val << EMIF_REG_T_RAS_SHIFT; + + val = max(min_tck->tWR, ns_2_cycles(timings->tWR)) - 1; + tim1 |= val << EMIF_REG_T_WR_SHIFT; + + val = max(min_tck->tRCD, ns_2_cycles(timings->tRCD)) - 1; + tim1 |= val << EMIF_REG_T_RCD_SHIFT; + + val = max(min_tck->tRP_AB, ns_2_cycles(timings->tRPab)) - 1; + tim1 |= val << EMIF_REG_T_RP_SHIFT; + + return tim1; +} + +static u32 get_sdram_tim_2_reg(const struct lpddr2_ac_timings *timings, + const struct lpddr2_min_tck *min_tck) +{ + u32 tim2 = 0, val = 0; + val = max(min_tck->tCKE, timings->tCKE) - 1; + tim2 |= val << EMIF_REG_T_CKE_SHIFT; + + val = max(min_tck->tRTP, ns_x2_2_cycles(timings->tRTPx2)) - 1; + tim2 |= val << EMIF_REG_T_RTP_SHIFT; + + /* + * tXSRD = tRFCab + 10 ns. XSRD and XSNR should have the + * same value + */ + val = ns_2_cycles(timings->tXSR) - 1; + tim2 |= val << EMIF_REG_T_XSRD_SHIFT; + tim2 |= val << EMIF_REG_T_XSNR_SHIFT; + + val = max(min_tck->tXP, ns_x2_2_cycles(timings->tXPx2)) - 1; + tim2 |= val << EMIF_REG_T_XP_SHIFT; + + return tim2; +} + +static u32 get_sdram_tim_3_reg(const struct lpddr2_ac_timings *timings, + const struct lpddr2_min_tck *min_tck, + const struct lpddr2_addressing *addressing) +{ + u32 tim3 = 0, val = 0; + val = min(timings->tRASmax * 10 / addressing->t_REFI_us_x10 - 1, 0xF); + tim3 |= val << EMIF_REG_T_RAS_MAX_SHIFT; + + val = ns_2_cycles(timings->tRFCab) - 1; + tim3 |= val << EMIF_REG_T_RFC_SHIFT; + + val = ns_x2_2_cycles(timings->tDQSCKMAXx2) - 1; + tim3 |= val << EMIF_REG_T_TDQSCKMAX_SHIFT; + + val = ns_2_cycles(timings->tZQCS) - 1; + tim3 |= val << EMIF_REG_ZQ_ZQCS_SHIFT; + + val = max(min_tck->tCKESR, ns_2_cycles(timings->tCKESR)) - 1; + tim3 |= val << EMIF_REG_T_CKESR_SHIFT; + + return tim3; +} + +static u32 get_zq_config_reg(const struct lpddr2_device_details *cs1_device, + const struct lpddr2_addressing *addressing, + u8 volt_ramp) +{ + u32 zq = 0, val = 0; + if (volt_ramp) + val = + EMIF_ZQCS_INTERVAL_DVFS_IN_US * 10 / + addressing->t_REFI_us_x10; + else + val = + EMIF_ZQCS_INTERVAL_NORMAL_IN_US * 10 / + addressing->t_REFI_us_x10; + zq |= val << EMIF_REG_ZQ_REFINTERVAL_SHIFT; + + zq |= (REG_ZQ_ZQCL_MULT - 1) << EMIF_REG_ZQ_ZQCL_MULT_SHIFT; + + zq |= (REG_ZQ_ZQINIT_MULT - 1) << EMIF_REG_ZQ_ZQINIT_MULT_SHIFT; + + zq |= REG_ZQ_SFEXITEN_ENABLE << EMIF_REG_ZQ_SFEXITEN_SHIFT; + + /* + * Assuming that two chipselects have a single calibration resistor + * If there are indeed two calibration resistors, then this flag should + * be enabled to take advantage of dual calibration feature. + * This data should ideally come from board files. But considering + * that none of the boards today have calibration resistors per CS, + * it would be an unnecessary overhead. + */ + zq |= REG_ZQ_DUALCALEN_DISABLE << EMIF_REG_ZQ_DUALCALEN_SHIFT; + + zq |= REG_ZQ_CS0EN_ENABLE << EMIF_REG_ZQ_CS0EN_SHIFT; + + zq |= (cs1_device ? 1 : 0) << EMIF_REG_ZQ_CS1EN_SHIFT; + + return zq; +} + +static u32 get_temp_alert_config(const struct lpddr2_device_details *cs1_device, + const struct lpddr2_addressing *addressing, + u8 is_derated) +{ + u32 alert = 0, interval; + interval = + TEMP_ALERT_POLL_INTERVAL_MS * 10000 / addressing->t_REFI_us_x10; + if (is_derated) + interval *= 4; + alert |= interval << EMIF_REG_TA_REFINTERVAL_SHIFT; + + alert |= TEMP_ALERT_CONFIG_DEVCT_1 << EMIF_REG_TA_DEVCNT_SHIFT; + + alert |= TEMP_ALERT_CONFIG_DEVWDT_32 << EMIF_REG_TA_DEVWDT_SHIFT; + + alert |= 1 << EMIF_REG_TA_SFEXITEN_SHIFT; + + alert |= 1 << EMIF_REG_TA_CS0EN_SHIFT; + + alert |= (cs1_device ? 1 : 0) << EMIF_REG_TA_CS1EN_SHIFT; + + return alert; +} + +static u32 get_read_idle_ctrl_reg(u8 volt_ramp) +{ + u32 idle = 0, val = 0; + if (volt_ramp) + val = ns_2_cycles(READ_IDLE_INTERVAL_DVFS) / 64 - 1; + else + /*Maximum value in normal conditions - suggested by hw team */ + val = 0x1FF; + idle |= val << EMIF_REG_READ_IDLE_INTERVAL_SHIFT; + + idle |= EMIF_REG_READ_IDLE_LEN_VAL << EMIF_REG_READ_IDLE_LEN_SHIFT; + + return idle; +} + +static u32 get_ddr_phy_ctrl_1(u32 freq, u8 RL) +{ + u32 phy = 0, val = 0; + + phy |= (RL + 2) << EMIF_REG_READ_LATENCY_SHIFT; + + if (freq <= 100000000) + val = EMIF_DLL_SLAVE_DLY_CTRL_100_MHZ_AND_LESS; + else if (freq <= 200000000) + val = EMIF_DLL_SLAVE_DLY_CTRL_200_MHZ; + else + val = EMIF_DLL_SLAVE_DLY_CTRL_400_MHZ; + phy |= val << EMIF_REG_DLL_SLAVE_DLY_CTRL_SHIFT; + + /* Other fields are constant magic values. Hardcode them together */ + phy |= EMIF_DDR_PHY_CTRL_1_BASE_VAL << + EMIF_EMIF_DDR_PHY_CTRL_1_BASE_VAL_SHIFT; + + return phy; +} + +static u32 get_emif_mem_size(struct emif_device_details *devices) +{ + u32 size_mbytes = 0, temp; + + if (!devices) + return 0; + + if (devices->cs0_device_details) { + temp = devices->cs0_device_details->density; + size_mbytes += lpddr2_density_2_size_in_mbytes[temp]; + } + + if (devices->cs1_device_details) { + temp = devices->cs1_device_details->density; + size_mbytes += lpddr2_density_2_size_in_mbytes[temp]; + } + /* convert to bytes */ + return size_mbytes << 20; +} + +/* Gets the encoding corresponding to a given DMM section size */ +u32 get_dmm_section_size_map(u32 section_size) +{ + /* + * Section size mapping: + * 0x0: 16-MiB section + * 0x1: 32-MiB section + * 0x2: 64-MiB section + * 0x3: 128-MiB section + * 0x4: 256-MiB section + * 0x5: 512-MiB section + * 0x6: 1-GiB section + * 0x7: 2-GiB section + */ + section_size >>= 24; /* divide by 16 MB */ + return log_2_n_round_down(section_size); +} + +static void emif_calculate_regs( + const struct emif_device_details *emif_dev_details, + u32 freq, struct emif_regs *regs) +{ + u32 temp, sys_freq; + const struct lpddr2_addressing *addressing; + const struct lpddr2_ac_timings *timings; + const struct lpddr2_min_tck *min_tck; + const struct lpddr2_device_details *cs0_dev_details = + emif_dev_details->cs0_device_details; + const struct lpddr2_device_details *cs1_dev_details = + emif_dev_details->cs1_device_details; + const struct lpddr2_device_timings *cs0_dev_timings = + emif_dev_details->cs0_device_timings; + + emif_assert(emif_dev_details); + emif_assert(regs); + /* + * You can not have a device on CS1 without one on CS0 + * So configuring EMIF without a device on CS0 doesn't + * make sense + */ + emif_assert(cs0_dev_details); + emif_assert(cs0_dev_details->type != LPDDR2_TYPE_NVM); + /* + * If there is a device on CS1 it should be same type as CS0 + * (or NVM. But NVM is not supported in this driver yet) + */ + emif_assert((cs1_dev_details == NULL) || + (cs1_dev_details->type == LPDDR2_TYPE_NVM) || + (cs0_dev_details->type == cs1_dev_details->type)); + emif_assert(freq <= MAX_LPDDR2_FREQ); + + set_ddr_clk_period(freq); + + /* + * The device on CS0 is used for all timing calculations + * There is only one set of registers for timings per EMIF. So, if the + * second CS(CS1) has a device, it should have the same timings as the + * device on CS0 + */ + timings = get_timings_table(cs0_dev_timings->ac_timings, freq); + emif_assert(timings); + min_tck = cs0_dev_timings->min_tck; + + temp = addressing_table_index(cs0_dev_details->type, + cs0_dev_details->density, + cs0_dev_details->io_width); + + emif_assert((temp >= 0)); + addressing = &(addressing_table[temp]); + emif_assert(addressing); + + sys_freq = get_sys_clk_freq(); + + regs->sdram_config_init = get_sdram_config_reg(cs0_dev_details, + cs1_dev_details, + addressing, RL_BOOT); + + regs->sdram_config = get_sdram_config_reg(cs0_dev_details, + cs1_dev_details, + addressing, RL_FINAL); + + regs->ref_ctrl = get_sdram_ref_ctrl(freq, addressing); + + regs->sdram_tim1 = get_sdram_tim_1_reg(timings, min_tck, addressing); + + regs->sdram_tim2 = get_sdram_tim_2_reg(timings, min_tck); + + regs->sdram_tim3 = get_sdram_tim_3_reg(timings, min_tck, addressing); + + regs->read_idle_ctrl = get_read_idle_ctrl_reg(LPDDR2_VOLTAGE_STABLE); + + regs->temp_alert_config = + get_temp_alert_config(cs1_dev_details, addressing, 0); + + regs->zq_config = get_zq_config_reg(cs1_dev_details, addressing, + LPDDR2_VOLTAGE_STABLE); + + regs->emif_ddr_phy_ctlr_1_init = + get_ddr_phy_ctrl_1(sys_freq / 2, RL_BOOT); + + regs->emif_ddr_phy_ctlr_1 = + get_ddr_phy_ctrl_1(freq, RL_FINAL); + + regs->freq = freq; + + print_timing_reg(regs->sdram_config_init); + print_timing_reg(regs->sdram_config); + print_timing_reg(regs->ref_ctrl); + print_timing_reg(regs->sdram_tim1); + print_timing_reg(regs->sdram_tim2); + print_timing_reg(regs->sdram_tim3); + print_timing_reg(regs->read_idle_ctrl); + print_timing_reg(regs->temp_alert_config); + print_timing_reg(regs->zq_config); + print_timing_reg(regs->emif_ddr_phy_ctlr_1); + print_timing_reg(regs->emif_ddr_phy_ctlr_1_init); +} +#endif /* CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS */ + +#ifdef CONFIG_SYS_AUTOMATIC_SDRAM_DETECTION +const char *get_lpddr2_type(u8 type_id) +{ + switch (type_id) { + case LPDDR2_TYPE_S4: + return "LPDDR2-S4"; + case LPDDR2_TYPE_S2: + return "LPDDR2-S2"; + default: + return NULL; + } +} + +const char *get_lpddr2_io_width(u8 width_id) +{ + switch (width_id) { + case LPDDR2_IO_WIDTH_8: + return "x8"; + case LPDDR2_IO_WIDTH_16: + return "x16"; + case LPDDR2_IO_WIDTH_32: + return "x32"; + default: + return NULL; + } +} + +const char *get_lpddr2_manufacturer(u32 manufacturer) +{ + switch (manufacturer) { + case LPDDR2_MANUFACTURER_SAMSUNG: + return "Samsung"; + case LPDDR2_MANUFACTURER_QIMONDA: + return "Qimonda"; + case LPDDR2_MANUFACTURER_ELPIDA: + return "Elpida"; + case LPDDR2_MANUFACTURER_ETRON: + return "Etron"; + case LPDDR2_MANUFACTURER_NANYA: + return "Nanya"; + case LPDDR2_MANUFACTURER_HYNIX: + return "Hynix"; + case LPDDR2_MANUFACTURER_MOSEL: + return "Mosel"; + case LPDDR2_MANUFACTURER_WINBOND: + return "Winbond"; + case LPDDR2_MANUFACTURER_ESMT: + return "ESMT"; + case LPDDR2_MANUFACTURER_SPANSION: + return "Spansion"; + case LPDDR2_MANUFACTURER_SST: + return "SST"; + case LPDDR2_MANUFACTURER_ZMOS: + return "ZMOS"; + case LPDDR2_MANUFACTURER_INTEL: + return "Intel"; + case LPDDR2_MANUFACTURER_NUMONYX: + return "Numonyx"; + case LPDDR2_MANUFACTURER_MICRON: + return "Micron"; + default: + return NULL; + } +} + +static void display_sdram_details(u32 emif_nr, u32 cs, + struct lpddr2_device_details *device) +{ + const char *mfg_str; + const char *type_str; + char density_str[10]; + u32 density; + + debug("EMIF%d CS%d\t", emif_nr, cs); + + if (!device) { + debug("None\n"); + return; + } + + mfg_str = get_lpddr2_manufacturer(device->manufacturer); + type_str = get_lpddr2_type(device->type); + + density = lpddr2_density_2_size_in_mbytes[device->density]; + if ((density / 1024 * 1024) == density) { + density /= 1024; + sprintf(density_str, "%d GB", density); + } else + sprintf(density_str, "%d MB", density); + if (mfg_str && type_str) + debug("%s\t\t%s\t%s\n", mfg_str, type_str, density_str); +} + +static u8 is_lpddr2_sdram_present(u32 base, u32 cs, + struct lpddr2_device_details *lpddr2_device) +{ + u32 mr = 0, temp; + + mr = get_mr(base, cs, LPDDR2_MR0); + if (mr > 0xFF) { + /* Mode register value bigger than 8 bit */ + return 0; + } + + temp = (mr & LPDDR2_MR0_DI_MASK) >> LPDDR2_MR0_DI_SHIFT; + if (temp) { + /* Not SDRAM */ + return 0; + } + temp = (mr & LPDDR2_MR0_DNVI_MASK) >> LPDDR2_MR0_DNVI_SHIFT; + + if (temp) { + /* DNV supported - But DNV is only supported for NVM */ + return 0; + } + + mr = get_mr(base, cs, LPDDR2_MR4); + if (mr > 0xFF) { + /* Mode register value bigger than 8 bit */ + return 0; + } + + mr = get_mr(base, cs, LPDDR2_MR5); + if (mr >= 0xFF) { + /* Mode register value bigger than 8 bit */ + return 0; + } + + if (!get_lpddr2_manufacturer(mr)) { + /* Manufacturer not identified */ + return 0; + } + lpddr2_device->manufacturer = mr; + + mr = get_mr(base, cs, LPDDR2_MR6); + if (mr >= 0xFF) { + /* Mode register value bigger than 8 bit */ + return 0; + } + + mr = get_mr(base, cs, LPDDR2_MR7); + if (mr >= 0xFF) { + /* Mode register value bigger than 8 bit */ + return 0; + } + + mr = get_mr(base, cs, LPDDR2_MR8); + if (mr >= 0xFF) { + /* Mode register value bigger than 8 bit */ + return 0; + } + + temp = (mr & MR8_TYPE_MASK) >> MR8_TYPE_SHIFT; + if (!get_lpddr2_type(temp)) { + /* Not SDRAM */ + return 0; + } + lpddr2_device->type = temp; + + temp = (mr & MR8_DENSITY_MASK) >> MR8_DENSITY_SHIFT; + if (temp > LPDDR2_DENSITY_32Gb) { + /* Density not supported */ + return 0; + } + lpddr2_device->density = temp; + + temp = (mr & MR8_IO_WIDTH_MASK) >> MR8_IO_WIDTH_SHIFT; + if (!get_lpddr2_io_width(temp)) { + /* IO width unsupported value */ + return 0; + } + lpddr2_device->io_width = temp; + + /* + * If all the above tests pass we should + * have a device on this chip-select + */ + return 1; +} + +struct lpddr2_device_details *emif_get_device_details(u32 emif_nr, u8 cs, + struct lpddr2_device_details *lpddr2_dev_details) +{ + u32 phy; + u32 base = (emif_nr == 1) ? EMIF1_BASE : EMIF2_BASE; + + struct emif_reg_struct *emif = (struct emif_reg_struct *)base; + + if (!lpddr2_dev_details) + return NULL; + + /* Do the minimum init for mode register accesses */ + if (!running_from_sdram()) { + phy = get_ddr_phy_ctrl_1(get_sys_clk_freq() / 2, RL_BOOT); + writel(phy, &emif->emif_ddr_phy_ctrl_1); + } + + if (!(is_lpddr2_sdram_present(base, cs, lpddr2_dev_details))) + return NULL; + + display_sdram_details(emif_num(base), cs, lpddr2_dev_details); + + return lpddr2_dev_details; +} +#endif /* CONFIG_SYS_AUTOMATIC_SDRAM_DETECTION */ + +static void do_sdram_init(u32 base) +{ + const struct emif_regs *regs; + u32 in_sdram, emif_nr; + + debug(">>do_sdram_init() %x\n", base); + + in_sdram = running_from_sdram(); + emif_nr = (base == EMIF1_BASE) ? 1 : 2; + +#ifdef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS + emif_get_reg_dump(emif_nr, ®s); + if (!regs) { + debug("EMIF: reg dump not provided\n"); + return; + } +#else + /* + * The user has not provided the register values. We need to + * calculate it based on the timings and the DDR frequency + */ + struct emif_device_details dev_details; + struct emif_regs calculated_regs; + + /* + * Get device details: + * - Discovered if CONFIG_SYS_AUTOMATIC_SDRAM_DETECTION is set + * - Obtained from user otherwise + */ + struct lpddr2_device_details cs0_dev_details, cs1_dev_details; + emif_reset_phy(base); + dev_details.cs0_device_details = emif_get_device_details(base, CS0, + &cs0_dev_details); + dev_details.cs1_device_details = emif_get_device_details(base, CS1, + &cs1_dev_details); + emif_reset_phy(base); + + /* Return if no devices on this EMIF */ + if (!dev_details.cs0_device_details && + !dev_details.cs1_device_details) { + emif_sizes[emif_nr - 1] = 0; + return; + } + + if (!in_sdram) + emif_sizes[emif_nr - 1] = get_emif_mem_size(&dev_details); + + /* + * Get device timings: + * - Default timings specified by JESD209-2 if + * CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS is set + * - Obtained from user otherwise + */ + emif_get_device_timings(emif_nr, &dev_details.cs0_device_timings, + &dev_details.cs1_device_timings); + + /* Calculate the register values */ + emif_calculate_regs(&dev_details, omap_ddr_clk(), &calculated_regs); + regs = &calculated_regs; +#endif /* CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS */ + + /* + * Initializing the LPDDR2 device can not happen from SDRAM. + * Changing the timing registers in EMIF can happen(going from one + * OPP to another) + */ + if (!in_sdram) + lpddr2_init(base, regs); + + /* Write to the shadow registers */ + emif_update_timings(base, regs); + + debug("<<do_sdram_init() %x\n", base); +} + +void emif_post_init_config(u32 base) +{ + struct emif_reg_struct *emif = (struct emif_reg_struct *)base; + u32 omap_rev = omap_revision(); + + if (omap_rev == OMAP5430_ES1_0) + return; + + /* reset phy on ES2.0 */ + if (omap_rev == OMAP4430_ES2_0) + emif_reset_phy(base); + + /* Put EMIF back in smart idle on ES1.0 */ + if (omap_rev == OMAP4430_ES1_0) + writel(0x80000000, &emif->emif_pwr_mgmt_ctrl); +} + +void dmm_init(u32 base) +{ + const struct dmm_lisa_map_regs *lisa_map_regs; + +#ifdef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS + emif_get_dmm_regs(&lisa_map_regs); +#else + u32 emif1_size, emif2_size, mapped_size, section_map = 0; + u32 section_cnt, sys_addr; + struct dmm_lisa_map_regs lis_map_regs_calculated = {0}; + + mapped_size = 0; + section_cnt = 3; + sys_addr = CONFIG_SYS_SDRAM_BASE; + emif1_size = emif_sizes[0]; + emif2_size = emif_sizes[1]; + debug("emif1_size 0x%x emif2_size 0x%x\n", emif1_size, emif2_size); + + if (!emif1_size && !emif2_size) + return; + + /* symmetric interleaved section */ + if (emif1_size && emif2_size) { + mapped_size = min(emif1_size, emif2_size); + section_map = DMM_LISA_MAP_INTERLEAVED_BASE_VAL; + section_map |= 0 << EMIF_SDRC_ADDR_SHIFT; + /* only MSB */ + section_map |= (sys_addr >> 24) << + EMIF_SYS_ADDR_SHIFT; + section_map |= get_dmm_section_size_map(mapped_size * 2) + << EMIF_SYS_SIZE_SHIFT; + lis_map_regs_calculated.dmm_lisa_map_3 = section_map; + emif1_size -= mapped_size; + emif2_size -= mapped_size; + sys_addr += (mapped_size * 2); + section_cnt--; + } + + /* + * Single EMIF section(we can have a maximum of 1 single EMIF + * section- either EMIF1 or EMIF2 or none, but not both) + */ + if (emif1_size) { + section_map = DMM_LISA_MAP_EMIF1_ONLY_BASE_VAL; + section_map |= get_dmm_section_size_map(emif1_size) + << EMIF_SYS_SIZE_SHIFT; + /* only MSB */ + section_map |= (mapped_size >> 24) << + EMIF_SDRC_ADDR_SHIFT; + /* only MSB */ + section_map |= (sys_addr >> 24) << EMIF_SYS_ADDR_SHIFT; + section_cnt--; + } + if (emif2_size) { + section_map = DMM_LISA_MAP_EMIF2_ONLY_BASE_VAL; + section_map |= get_dmm_section_size_map(emif2_size) << + EMIF_SYS_SIZE_SHIFT; + /* only MSB */ + section_map |= mapped_size >> 24 << EMIF_SDRC_ADDR_SHIFT; + /* only MSB */ + section_map |= sys_addr >> 24 << EMIF_SYS_ADDR_SHIFT; + section_cnt--; + } + + if (section_cnt == 2) { + /* Only 1 section - either symmetric or single EMIF */ + lis_map_regs_calculated.dmm_lisa_map_3 = section_map; + lis_map_regs_calculated.dmm_lisa_map_2 = 0; + lis_map_regs_calculated.dmm_lisa_map_1 = 0; + } else { + /* 2 sections - 1 symmetric, 1 single EMIF */ + lis_map_regs_calculated.dmm_lisa_map_2 = section_map; + lis_map_regs_calculated.dmm_lisa_map_1 = 0; + } + + /* TRAP for invalid TILER mappings in section 0 */ + lis_map_regs_calculated.dmm_lisa_map_0 = DMM_LISA_MAP_0_INVAL_ADDR_TRAP; + + lisa_map_regs = &lis_map_regs_calculated; +#endif + struct dmm_lisa_map_regs *hw_lisa_map_regs = + (struct dmm_lisa_map_regs *)base; + + writel(0, &hw_lisa_map_regs->dmm_lisa_map_3); + writel(0, &hw_lisa_map_regs->dmm_lisa_map_2); + writel(0, &hw_lisa_map_regs->dmm_lisa_map_1); + writel(0, &hw_lisa_map_regs->dmm_lisa_map_0); + + writel(lisa_map_regs->dmm_lisa_map_3, + &hw_lisa_map_regs->dmm_lisa_map_3); + writel(lisa_map_regs->dmm_lisa_map_2, + &hw_lisa_map_regs->dmm_lisa_map_2); + writel(lisa_map_regs->dmm_lisa_map_1, + &hw_lisa_map_regs->dmm_lisa_map_1); + writel(lisa_map_regs->dmm_lisa_map_0, + &hw_lisa_map_regs->dmm_lisa_map_0); + + if (omap_revision() >= OMAP4460_ES1_0) { + hw_lisa_map_regs = + (struct dmm_lisa_map_regs *)MA_BASE; + + writel(lisa_map_regs->dmm_lisa_map_3, + &hw_lisa_map_regs->dmm_lisa_map_3); + writel(lisa_map_regs->dmm_lisa_map_2, + &hw_lisa_map_regs->dmm_lisa_map_2); + writel(lisa_map_regs->dmm_lisa_map_1, + &hw_lisa_map_regs->dmm_lisa_map_1); + writel(lisa_map_regs->dmm_lisa_map_0, + &hw_lisa_map_regs->dmm_lisa_map_0); + } +} + +/* + * SDRAM initialization: + * SDRAM initialization has two parts: + * 1. Configuring the SDRAM device + * 2. Update the AC timings related parameters in the EMIF module + * (1) should be done only once and should not be done while we are + * running from SDRAM. + * (2) can and should be done more than once if OPP changes. + * Particularly, this may be needed when we boot without SPL and + * and using Configuration Header(CH). ROM code supports only at 50% OPP + * at boot (low power boot). So u-boot has to switch to OPP100 and update + * the frequency. So, + * Doing (1) and (2) makes sense - first time initialization + * Doing (2) and not (1) makes sense - OPP change (when using CH) + * Doing (1) and not (2) doen't make sense + * See do_sdram_init() for the details + */ +void sdram_init(void) +{ + u32 in_sdram, size_prog, size_detect; + + debug(">>sdram_init()\n"); + + if (omap_hw_init_context() == OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL) + return; + + in_sdram = running_from_sdram(); + debug("in_sdram = %d\n", in_sdram); + + if (!in_sdram) + bypass_dpll(&prcm->cm_clkmode_dpll_core); + + + do_sdram_init(EMIF1_BASE); + do_sdram_init(EMIF2_BASE); + + if (!in_sdram) { + dmm_init(DMM_BASE); + emif_post_init_config(EMIF1_BASE); + emif_post_init_config(EMIF2_BASE); + } + + /* for the shadow registers to take effect */ + freq_update_core(); + + /* Do some testing after the init */ + if (!in_sdram) { + size_prog = omap_sdram_size(); + size_detect = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, + size_prog); + /* Compare with the size programmed */ + if (size_detect != size_prog) { + printf("SDRAM: identified size not same as expected" + " size identified: %x expected: %x\n", + size_detect, + size_prog); + } else + debug("get_ram_size() successful"); + } + + debug("<<sdram_init()\n"); +} diff --git a/arch/arm/cpu/armv7/omap-common/hwinit-common.c b/arch/arm/cpu/armv7/omap-common/hwinit-common.c new file mode 100644 index 0000000..f65705d --- /dev/null +++ b/arch/arm/cpu/armv7/omap-common/hwinit-common.c @@ -0,0 +1,267 @@ +/* + * + * Common functions for OMAP4/5 based boards + * + * (C) Copyright 2010 + * Texas Instruments, <www.ti.com> + * + * Author : + * Aneesh V <aneesh@ti.com> + * Steve Sakoman <steve@sakoman.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include <common.h> +#include <asm/arch/sys_proto.h> +#include <asm/sizes.h> +#include <asm/emif.h> +#include <asm/omap_common.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* + * This is used to verify if the configuration header + * was executed by rom code prior to control of transfer + * to the bootloader. SPL is responsible for saving and + * passing the boot_params pointer to the u-boot. + */ +struct omap_boot_parameters boot_params __attribute__ ((section(".data"))); + +#ifdef CONFIG_SPL_BUILD +/* + * We use static variables because global data is not ready yet. + * Initialized data is available in SPL right from the beginning. + * We would not typically need to save these parameters in regular + * U-Boot. This is needed only in SPL at the moment. + */ +u32 omap_bootmode = MMCSD_MODE_FAT; + +u32 omap_boot_device(void) +{ + return (u32) (boot_params.omap_bootdevice); +} + +u32 omap_boot_mode(void) +{ + return omap_bootmode; +} +#endif + +void do_set_mux(u32 base, struct pad_conf_entry const *array, int size) +{ + int i; + struct pad_conf_entry *pad = (struct pad_conf_entry *) array; + + for (i = 0; i < size; i++, pad++) + writew(pad->val, base + pad->offset); +} + +static void set_mux_conf_regs(void) +{ + switch (omap_hw_init_context()) { + case OMAP_INIT_CONTEXT_SPL: + set_muxconf_regs_essential(); + break; + case OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL: +#ifdef CONFIG_SYS_ENABLE_PADS_ALL + set_muxconf_regs_non_essential(); +#endif + break; + case OMAP_INIT_CONTEXT_UBOOT_FROM_NOR: + case OMAP_INIT_CONTEXT_UBOOT_AFTER_CH: + set_muxconf_regs_essential(); +#ifdef CONFIG_SYS_ENABLE_PADS_ALL + set_muxconf_regs_non_essential(); +#endif + break; + } +} + +u32 cortex_rev(void) +{ + + unsigned int rev; + + /* Read Main ID Register (MIDR) */ + asm ("mrc p15, 0, %0, c0, c0, 0" : "=r" (rev)); + + return rev; +} + +void omap_rev_string(char *omap_rev_string) +{ + u32 omap_rev = omap_revision(); + u32 omap_variant = (omap_rev & 0xFFFF0000) >> 16; + u32 major_rev = (omap_rev & 0x00000F00) >> 8; + u32 minor_rev = (omap_rev & 0x000000F0) >> 4; + + sprintf(omap_rev_string, "OMAP%x ES%x.%x", omap_variant, major_rev, + minor_rev); +} + +#ifdef CONFIG_SPL_BUILD +static void init_boot_params(void) +{ + boot_params_ptr = (u32 *) &boot_params; +} +#endif + +/* + * Routine: s_init + * Description: Does early system init of watchdog, muxing, andclocks + * Watchdog disable is done always. For the rest what gets done + * depends on the boot mode in which this function is executed + * 1. s_init of SPL running from SRAM + * 2. s_init of U-Boot running from FLASH + * 3. s_init of U-Boot loaded to SDRAM by SPL + * 4. s_init of U-Boot loaded to SDRAM by ROM code using the + * Configuration Header feature + * Please have a look at the respective functions to see what gets + * done in each of these cases + * This function is called with SRAM stack. + */ +void s_init(void) +{ + init_omap_revision(); + watchdog_init(); + set_mux_conf_regs(); +#ifdef CONFIG_SPL_BUILD + setup_clocks_for_console(); + preloader_console_init(); + do_io_settings(); +#endif + prcm_init(); +#ifdef CONFIG_SPL_BUILD + /* For regular u-boot sdram_init() is called from dram_init() */ + sdram_init(); + init_boot_params(); +#endif +} + +/* + * Routine: wait_for_command_complete + * Description: Wait for posting to finish on watchdog + */ +void wait_for_command_complete(struct watchdog *wd_base) +{ + int pending = 1; + do { + pending = readl(&wd_base->wwps); + } while (pending); +} + +/* + * Routine: watchdog_init + * Description: Shut down watch dogs + */ +void watchdog_init(void) +{ + struct watchdog *wd2_base = (struct watchdog *)WDT2_BASE; + + writel(WD_UNLOCK1, &wd2_base->wspr); + wait_for_command_complete(wd2_base); + writel(WD_UNLOCK2, &wd2_base->wspr); +} + + +/* + * This function finds the SDRAM size available in the system + * based on DMM section configurations + * This is needed because the size of memory installed may be + * different on different versions of the board + */ +u32 omap_sdram_size(void) +{ + u32 section, i, total_size = 0, size, addr; + + for (i = 0; i < 4; i++) { + section = __raw_readl(DMM_BASE + i*4); + addr = section & EMIF_SYS_ADDR_MASK; + /* See if the address is valid */ + if ((addr >= DRAM_ADDR_SPACE_START) && + (addr < DRAM_ADDR_SPACE_END)) { + size = ((section & EMIF_SYS_SIZE_MASK) >> + EMIF_SYS_SIZE_SHIFT); + size = 1 << size; + size *= SZ_16M; + total_size += size; + } + } + + return total_size; +} + + +/* + * Routine: dram_init + * Description: sets uboots idea of sdram size + */ +int dram_init(void) +{ + sdram_init(); + gd->ram_size = omap_sdram_size(); + return 0; +} + +/* + * Print board information + */ +int checkboard(void) +{ + puts(sysinfo.board_string); + return 0; +} + +/* +* This function is called by start_armboot. You can reliably use static +* data. Any boot-time function that require static data should be +* called from here +*/ +int arch_cpu_init(void) +{ + return 0; +} + +/* + * get_device_type(): tell if GP/HS/EMU/TST + */ +u32 get_device_type(void) +{ + return 0; +} + +/* + * Print CPU information + */ +int print_cpuinfo(void) +{ + char rev_string_buffer[50]; + + omap_rev_string(rev_string_buffer); + printf("CPU : %s\n", rev_string_buffer); + + return 0; +} +#ifndef CONFIG_SYS_DCACHE_OFF +void enable_caches(void) +{ + /* Enable D-cache. I-cache is already enabled in start.S */ + dcache_enable(); +} +#endif diff --git a/arch/arm/cpu/armv7/omap-common/lowlevel_init.S b/arch/arm/cpu/armv7/omap-common/lowlevel_init.S new file mode 100644 index 0000000..35f38ac --- /dev/null +++ b/arch/arm/cpu/armv7/omap-common/lowlevel_init.S @@ -0,0 +1,106 @@ +/* + * Board specific setup info + * + * (C) Copyright 2010 + * Texas Instruments, <www.ti.com> + * + * Author : + * Aneesh V <aneesh@ti.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <asm/arch/omap.h> + +.global save_boot_params +save_boot_params: + /* + * See if the rom code passed pointer is valid: + * It is not valid if it is not in non-secure SRAM + * This may happen if you are booting with the help of + * debugger + */ + ldr r2, =NON_SECURE_SRAM_START + cmp r2, r0 + bgt 1f + ldr r2, =NON_SECURE_SRAM_END + cmp r2, r0 + blt 1f + + /* + * store the boot params passed from rom code or saved + * and passed by SPL + */ + cmp r0, #0 + beq 1f + ldr r1, =boot_params + str r0, [r1] +#ifdef CONFIG_SPL_BUILD + /* Store the boot device in omap_boot_device */ + ldrb r2, [r0, #BOOT_DEVICE_OFFSET] @ r1 <- value of boot device + and r2, #BOOT_DEVICE_MASK + ldr r3, =boot_params + strb r2, [r3, #BOOT_DEVICE_OFFSET] @ omap_boot_device <- r1 + + /* boot mode is passed only for devices that can raw/fat mode */ + cmp r2, #2 + blt 2f + cmp r2, #7 + bgt 2f + /* Store the boot mode (raw/FAT) in omap_boot_mode */ + ldr r2, [r0, #DEV_DESC_PTR_OFFSET] @ get the device descriptor ptr + ldr r2, [r2, #DEV_DATA_PTR_OFFSET] @ get the pDeviceData ptr + ldr r2, [r2, #BOOT_MODE_OFFSET] @ get the boot mode + ldr r3, =omap_bootmode + str r2, [r3] +#endif +2: + ldrb r2, [r0, #CH_FLAGS_OFFSET] + ldr r3, =boot_params + strb r2, [r3, #CH_FLAGS_OFFSET] +1: + bx lr + + +.globl lowlevel_init +lowlevel_init: + /* + * Setup a temporary stack + */ + ldr sp, =LOW_LEVEL_SRAM_STACK + + /* + * Save the old lr(passed in ip) and the current lr to stack + */ + push {ip, lr} + + /* + * go setup pll, mux, memory + */ + bl s_init + pop {ip, pc} + +.globl set_pl310_ctrl_reg +set_pl310_ctrl_reg: + PUSH {r4-r11, lr} @ save registers - ROM code may pollute + @ our registers + LDR r12, =0x102 @ Set PL310 control register - value in R0 + .word 0xe1600070 @ SMC #0 - hand assembled because -march=armv5 + @ call ROM Code API to set control register + POP {r4-r11, pc} diff --git a/arch/arm/cpu/armv7/omap-common/mem-common.c b/arch/arm/cpu/armv7/omap-common/mem-common.c new file mode 100644 index 0000000..878f0e3 --- /dev/null +++ b/arch/arm/cpu/armv7/omap-common/mem-common.c @@ -0,0 +1,45 @@ +/* + * (C) Copyright 2010 + * Texas Instruments, <www.ti.com> + * + * Steve Sakoman <steve@sakoman.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <asm/arch/cpu.h> +#include <asm/arch/sys_proto.h> + +struct gpmc *gpmc_cfg; + +/***************************************************** + * gpmc_init(): init gpmc bus + * This code can only be executed from SRAM or SDRAM. + *****************************************************/ +void gpmc_init(void) +{ + gpmc_cfg = (struct gpmc *)GPMC_BASE; + + /* global settings */ + writel(0, &gpmc_cfg->irqenable); /* isr's sources masked */ + writel(0, &gpmc_cfg->timeout_control);/* timeout disable */ + + /* + * Disable the GPMC0 config set by ROM code + * It conflicts with our MPDB (both at 0x08000000) + */ + writel(0, &gpmc_cfg->cs[0].config7); +} diff --git a/arch/arm/cpu/armv7/omap-common/spl.c b/arch/arm/cpu/armv7/omap-common/spl.c index 2c59d2b..d6d7d65 100644 --- a/arch/arm/cpu/armv7/omap-common/spl.c +++ b/arch/arm/cpu/armv7/omap-common/spl.c @@ -38,6 +38,7 @@ DECLARE_GLOBAL_DATA_PTR; +u32* boot_params_ptr = NULL; struct spl_image_info spl_image; /* Define global data structure pointer to it*/ @@ -92,12 +93,16 @@ void spl_parse_image_header(const struct image_header *header) static void jump_to_image_no_args(void) { - typedef void (*image_entry_noargs_t)(void)__attribute__ ((noreturn)); + typedef void (*image_entry_noargs_t)(u32 *)__attribute__ ((noreturn)); image_entry_noargs_t image_entry = (image_entry_noargs_t) spl_image.entry_point; debug("image entry point: 0x%X\n", spl_image.entry_point); - image_entry(); + /* Pass the saved boot_params from rom code */ +#if defined(CONFIG_VIRTIO) || defined(CONFIG_ZEBU) + image_entry = 0x80100000; +#endif + image_entry((u32 *)&boot_params_ptr); } void jump_to_image_no_args(void) __attribute__ ((noreturn)); |