diff options
Diffstat (limited to 'arch/arm/cpu/arm1176')
| -rw-r--r-- | arch/arm/cpu/arm1176/start.S | 218 |
1 files changed, 0 insertions, 218 deletions
diff --git a/arch/arm/cpu/arm1176/start.S b/arch/arm/cpu/arm1176/start.S index 7f32db7..f04d268 100644 --- a/arch/arm/cpu/arm1176/start.S +++ b/arch/arm/cpu/arm1176/start.S @@ -108,12 +108,6 @@ _TEXT_BASE: _TEXT_PHY_BASE: .word CONFIG_SYS_PHY_UBOOT_BASE -#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC) -.globl _armboot_start -_armboot_start: - .word _start -#endif - /* * These are defined in the board-specific linker script. * Subtracting _start from them lets the linker put their @@ -157,7 +151,6 @@ _rel_dyn_end_ofs: _dynsym_start_ofs: .word __dynsym_start - _start -#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) /* IRQ stack memory (calculated at run-time) + 8 bytes */ .globl IRQ_STACK_START_IN IRQ_STACK_START_IN: @@ -288,7 +281,6 @@ stack_setup: cmp r0, r6 beq clear_bss -#ifndef CONFIG_SKIP_RELOCATE_UBOOT copy_loop: ldmia r0!, {r9-r10} /* copy from source address [r0] */ stmia r6!, {r9-r10} /* copy to target address [r1] */ @@ -335,7 +327,6 @@ fixnext: cmp r2, r3 blo fixloop #endif -#endif /* #ifndef CONFIG_SKIP_RELOCATE_UBOOT */ #ifdef CONFIG_ENABLE_MMU enable_mmu: @@ -406,9 +397,7 @@ _nand_boot: .word nand_boot ldr r0, _board_init_r_ofs adr r1, _start add lr, r0, r1 -#ifndef CONFIG_SKIP_RELOCATE_UBOOT add lr, lr, r9 -#endif /* setup parameters for board_init_r */ mov r0, r5 /* gd_t */ mov r1, r7 /* dest_addr */ @@ -419,188 +408,6 @@ _board_init_r_ofs: .word board_init_r - _start #endif -#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */ - -/* - * the actual reset code - */ - -reset: - /* - * set the cpu to SVC32 mode - */ - mrs r0, cpsr - bic r0, r0, #0x3f - orr r0, r0, #0xd3 - msr cpsr, r0 - -/* - ************************************************************************* - * - * CPU_init_critical registers - * - * setup important registers - * setup memory timing - * - ************************************************************************* - */ - /* - * we do sys-critical inits only at reboot, - * not when booting from ram! - */ -cpu_init_crit: - /* - * When booting from NAND - it has definitely been a reset, so, no need - * to flush caches and disable the MMU - */ -#ifndef CONFIG_NAND_SPL - /* - * flush v4 I/D caches - */ - mov r0, #0 - mcr p15, 0, r0, c7, c7, 0 /* flush v3/v4 cache */ - mcr p15, 0, r0, c8, c7, 0 /* flush v4 TLB */ - - /* - * disable MMU stuff and caches - */ - mrc p15, 0, r0, c1, c0, 0 - bic r0, r0, #0x00002300 @ clear bits 13, 9:8 (--V- --RS) - bic r0, r0, #0x00000087 @ clear bits 7, 2:0 (B--- -CAM) - orr r0, r0, #0x00000002 @ set bit 2 (A) Align - orr r0, r0, #0x00001000 @ set bit 12 (I) I-Cache - - /* Prepare to disable the MMU */ - adr r2, mmu_disable_phys - sub r2, r2, #(CONFIG_SYS_PHY_UBOOT_BASE - CONFIG_SYS_TEXT_BASE) - b mmu_disable - - .align 5 - /* Run in a single cache-line */ -mmu_disable: - mcr p15, 0, r0, c1, c0, 0 - nop - nop - mov pc, r2 -mmu_disable_phys: - -#ifdef CONFIG_DISABLE_TCM - /* - * Disable the TCMs - */ - mrc p15, 0, r0, c0, c0, 2 /* Return TCM details */ - cmp r0, #0 - beq skip_tcmdisable - mov r1, #0 - mov r2, #1 - tst r0, r2 - mcrne p15, 0, r1, c9, c1, 1 /* Disable Instruction TCM if present*/ - tst r0, r2, LSL #16 - mcrne p15, 0, r1, c9, c1, 0 /* Disable Data TCM if present*/ -skip_tcmdisable: -#endif -#endif - -#ifdef CONFIG_PERIPORT_REMAP - /* Peri port setup */ - ldr r0, =CONFIG_PERIPORT_BASE - orr r0, r0, #CONFIG_PERIPORT_SIZE - mcr p15,0,r0,c15,c2,4 -#endif - - /* - * Go setup Memory and board specific bits prior to relocation. - */ - bl lowlevel_init /* go setup pll,mux,memory */ - -#ifndef CONFIG_SKIP_RELOCATE_UBOOT -relocate: /* relocate U-Boot to RAM */ - adr r0, _start /* r0 <- current position of code */ - ldr r1, _TEXT_BASE /* test if we run from flash or RAM */ - cmp r0, r1 /* don't reloc during debug */ - beq stack_setup - - ldr r2, _armboot_start - ldr r3, _bss_start - sub r2, r3, r2 /* r2 <- size of armboot */ - add r2, r0, r2 /* r2 <- source end address */ - -copy_loop: - ldmia r0!, {r3-r10} /* copy from source address [r0] */ - stmia r1!, {r3-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end address [r2] */ - blo copy_loop -#endif /* CONFIG_SKIP_RELOCATE_UBOOT */ - -#ifdef CONFIG_ENABLE_MMU -enable_mmu: - /* enable domain access */ - ldr r5, =0x0000ffff - mcr p15, 0, r5, c3, c0, 0 /* load domain access register */ - - /* Set the TTB register */ - ldr r0, _mmu_table_base - ldr r1, =CONFIG_SYS_PHY_UBOOT_BASE - ldr r2, =0xfff00000 - bic r0, r0, r2 - orr r1, r0, r1 - mcr p15, 0, r1, c2, c0, 0 - - /* Enable the MMU */ - mrc p15, 0, r0, c1, c0, 0 - orr r0, r0, #1 /* Set CR_M to enable MMU */ - - /* Prepare to enable the MMU */ - adr r1, skip_hw_init - and r1, r1, #0x3fc - ldr r2, _TEXT_BASE - ldr r3, =0xfff00000 - and r2, r2, r3 - orr r2, r2, r1 - b mmu_enable - - .align 5 - /* Run in a single cache-line */ -mmu_enable: - - mcr p15, 0, r0, c1, c0, 0 - nop - nop - mov pc, r2 -skip_hw_init: -#endif - - /* Set up the stack */ -stack_setup: - ldr r0, =CONFIG_SYS_UBOOT_BASE /* base of copy in DRAM */ - sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */ - sub r0, r0, #GENERATED_GBL_DATA_SIZE /* bdinfo */ - sub sp, r0, #12 /* leave 3 words for abort-stack */ - bic sp, sp, #7 /* 8-byte alignment for ABI compliance */ - -clear_bss: - ldr r0, _bss_start /* find start of bss segment */ - ldr r1, _bss_end /* stop here */ - mov r2, #0 /* clear */ - -clbss_l: - str r2, [r0] /* clear loop... */ - add r0, r0, #4 - cmp r0, r1 - blo clbss_l - -#ifndef CONFIG_NAND_SPL - ldr pc, _start_armboot - -_start_armboot: - .word start_armboot -#else - b nand_boot -/* .word nand_boot*/ -#endif - -#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */ - #ifdef CONFIG_ENABLE_MMU _mmu_table_base: .word mmu_table @@ -687,14 +494,7 @@ phy_last_jump: /* Save user registers (now in svc mode) r0-r12 */ stmia sp, {r0 - r12} -#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC) - ldr r2, _armboot_start - sub r2, r2, #(CONFIG_SYS_MALLOC_LEN) - /* set base 2 words into abort stack */ - sub r2, r2, #(GENERATED_GBL_DATA_SIZE+8) -#else ldr r2, IRQ_STACK_START_IN -#endif /* get values for "aborted" pc and cpsr (into parm regs) */ ldmia r2, {r2 - r3} /* grab pointer to old stack */ @@ -709,16 +509,7 @@ phy_last_jump: .endm .macro get_bad_stack -#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC) - /* setup our mode stack (enter in banked mode) */ - ldr r13, _armboot_start - /* move past malloc pool */ - sub r13, r13, #(CONFIG_SYS_MALLOC_LEN) - /* move to reserved a couple spots for abort stack */ - sub r13, r13, #(GENERATED_GBL_DATA_SIZE + 8) -#else ldr r13, IRQ_STACK_START_IN @ setup our mode stack -#endif /* save caller lr in position 0 of saved stack */ str lr, [r13] @@ -743,16 +534,7 @@ phy_last_jump: sub r13, r13, #4 /* save R0's value. */ str r0, [r13] -#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC) - /* get data regions start */ - ldr r0, _armboot_start - /* move past malloc pool */ - sub r0, r0, #(CONFIG_SYS_MALLOC_LEN) - /* move past gbl and a couple spots for abort stack */ - sub r0, r0, #(GENERATED_GBL_DATA_SIZE + 8) -#else ldr r13, IRQ_STACK_START_IN @ setup our mode stack -#endif /* save caller lr in position 0 of saved stack */ str lr, [r0] /* get the spsr */ |