summaryrefslogtreecommitdiff
path: root/README
diff options
context:
space:
mode:
Diffstat (limited to 'README')
-rw-r--r--README104
1 files changed, 104 insertions, 0 deletions
diff --git a/README b/README
index 55c3fcd..f704eb3 100644
--- a/README
+++ b/README
@@ -2288,6 +2288,21 @@ CBFS (Coreboot Filesystem) support
9 i2c buses for Exynos4 and 1 for S3C24X0 SoCs from Samsung)
with a fix speed from 100000 and the slave addr 0!
+ - drivers/i2c/ihs_i2c.c
+ - activate this driver with CONFIG_SYS_I2C_IHS
+ - CONFIG_SYS_I2C_IHS_CH0 activate hardware channel 0
+ - CONFIG_SYS_I2C_IHS_SPEED_0 speed channel 0
+ - CONFIG_SYS_I2C_IHS_SLAVE_0 slave addr channel 0
+ - CONFIG_SYS_I2C_IHS_CH1 activate hardware channel 1
+ - CONFIG_SYS_I2C_IHS_SPEED_1 speed channel 1
+ - CONFIG_SYS_I2C_IHS_SLAVE_1 slave addr channel 1
+ - CONFIG_SYS_I2C_IHS_CH2 activate hardware channel 2
+ - CONFIG_SYS_I2C_IHS_SPEED_2 speed channel 2
+ - CONFIG_SYS_I2C_IHS_SLAVE_2 slave addr channel 2
+ - CONFIG_SYS_I2C_IHS_CH3 activate hardware channel 3
+ - CONFIG_SYS_I2C_IHS_SPEED_3 speed channel 3
+ - CONFIG_SYS_I2C_IHS_SLAVE_3 slave addr channel 3
+
additional defines:
CONFIG_SYS_NUM_I2C_BUSES
@@ -3254,6 +3269,11 @@ FIT uImage format:
disabled. If a board need legacy image format support
enable this through CONFIG_IMAGE_FORMAT_LEGACY
+ CONFIG_FIT_DISABLE_SHA256
+ Supporting SHA256 hashes has quite an impact on binary size.
+ For constrained systems sha256 hash support can be disabled
+ with this option.
+
- Standalone program support:
CONFIG_STANDALONE_LOAD_ADDR
@@ -3716,6 +3736,22 @@ Configuration Settings:
- CONFIG_SYS_MALLOC_LEN:
Size of DRAM reserved for malloc() use.
+- CONFIG_SYS_MALLOC_F_LEN
+ Size of the malloc() pool for use before relocation. If
+ this is defined, then a very simple malloc() implementation
+ will become available before relocation. The address is just
+ below the global data, and the stack is moved down to make
+ space.
+
+ This feature allocates regions with increasing addresses
+ within the region. calloc() is supported, but realloc()
+ is not available. free() is supported but does nothing.
+ The memory will be freed (or in fact just forgotton) when
+ U-Boot relocates itself.
+
+ Pre-relocation malloc() is only supported on sandbox
+ at present but is fairly easy to enable for other archs.
+
- CONFIG_SYS_BOOTM_LEN:
Normally compressed uImages are limited to an
uncompressed size of 8 MBytes. If this is not enough,
@@ -4069,6 +4105,43 @@ to save the current settings.
environment area within the total memory of your DataFlash placed
at the specified address.
+- CONFIG_ENV_IS_IN_SPI_FLASH:
+
+ Define this if you have a SPI Flash memory device which you
+ want to use for the environment.
+
+ - CONFIG_ENV_OFFSET:
+ - CONFIG_ENV_SIZE:
+
+ These two #defines specify the offset and size of the
+ environment area within the SPI Flash. CONFIG_ENV_OFFSET must be
+ aligned to an erase sector boundary.
+
+ - CONFIG_ENV_SECT_SIZE:
+
+ Define the SPI flash's sector size.
+
+ - CONFIG_ENV_OFFSET_REDUND (optional):
+
+ This setting describes a second storage area of CONFIG_ENV_SIZE
+ size used to hold a redundant copy of the environment data, so
+ that there is a valid backup copy in case there is a power failure
+ during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be
+ aligned to an erase sector boundary.
+
+ - CONFIG_ENV_SPI_BUS (optional):
+ - CONFIG_ENV_SPI_CS (optional):
+
+ Define the SPI bus and chip select. If not defined they will be 0.
+
+ - CONFIG_ENV_SPI_MAX_HZ (optional):
+
+ Define the SPI max work clock. If not defined then use 1MHz.
+
+ - CONFIG_ENV_SPI_MODE (optional):
+
+ Define the SPI work mode. If not defined then use SPI_MODE_3.
+
- CONFIG_ENV_IS_IN_REMOTE:
Define this if you have a remote memory space which you
@@ -4156,6 +4229,37 @@ but it can not erase, write this NOR flash by SRIO or PCIE interface.
You will probably want to define these to avoid a really noisy system
when storing the env in UBI.
+- CONFIG_ENV_IS_IN_FAT:
+ Define this if you want to use the FAT file system for the environment.
+
+ - FAT_ENV_INTERFACE:
+
+ Define this to a string that is the name of the block device.
+
+ - FAT_ENV_DEV_AND_PART:
+
+ Define this to a string to specify the partition of the device. It can
+ be as following:
+
+ "D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1)
+ - "D:P": device D partition P. Error occurs if device D has no
+ partition table.
+ - "D:0": device D.
+ - "D" or "D:": device D partition 1 if device D has partition
+ table, or the whole device D if has no partition
+ table.
+ - "D:auto": first partition in device D with bootable flag set.
+ If none, first valid paratition in device D. If no
+ partition table then means device D.
+
+ - FAT_ENV_FILE:
+
+ It's a string of the FAT file name. This file use to store the
+ envrionment.
+
+ - CONFIG_FAT_WRITE:
+ This should be defined. Otherwise it cannot save the envrionment file.
+
- CONFIG_ENV_IS_IN_MMC:
Define this if you have an MMC device which you want to use for the