diff options
Diffstat (limited to 'README')
| -rw-r--r-- | README | 73 |
1 files changed, 66 insertions, 7 deletions
@@ -1207,7 +1207,12 @@ The following options need to be configured: clock chips. See common/cmd_i2c.c for a description of the command line interface. - CONFIG_HARD_I2C selects the CPM hardware driver for I2C. + CONFIG_I2C_CMD_TREE is a recommended option that places + all I2C commands under a single 'i2c' root command. The + older 'imm', 'imd', 'iprobe' etc. commands are considered + deprecated and may disappear in the future. + + CONFIG_HARD_I2C selects a hardware I2C controller. CONFIG_SOFT_I2C configures u-boot to use a software (aka bit-banging) driver instead of CPM or similar hardware @@ -1312,6 +1317,42 @@ The following options need to be configured: in u-boot bd_info structure based on u-boot environment variable "i2cfast". (see also i2cfast) + CONFIG_I2C_MULTI_BUS + + This option allows the use of multiple I2C buses, each of which + must have a controller. At any point in time, only one bus is + active. To switch to a different bus, use the 'i2c dev' command. + Note that bus numbering is zero-based. + + CFG_I2C_NOPROBES + + This option specifies a list of I2C devices that will be skipped + when the 'i2c probe' command is issued (or 'iprobe' using the legacy + command). If CONFIG_I2C_MULTI_BUS is set, specify a list of bus-device + pairs. Otherwise, specify a 1D array of device addresses + + e.g. + #undef CONFIG_I2C_MULTI_BUS + #define CFG_I2C_NOPROBES {0x50,0x68} + + will skip addresses 0x50 and 0x68 on a board with one I2C bus + + #define CONFIG_I2C_MULTI_BUS + #define CFG_I2C_MULTI_NOPROBES {{0,0x50},{0,0x68},{1,0x54}} + + will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1 + + CFG_SPD_BUS_NUM + + If defined, then this indicates the I2C bus number for DDR SPD. + If not defined, then U-Boot assumes that SPD is on I2C bus 0. + + CONFIG_FSL_I2C + + Define this option if you want to use Freescale's I2C driver in + drivers/fsl_i2c.c. + + - SPI Support: CONFIG_SPI Enables SPI driver (so far only tested with @@ -1470,8 +1511,8 @@ The following options need to be configured: Enable auto completion of commands using TAB. - Note that this feature has NOT been implemented yet - for the "hush" shell. + Note that this feature has NOT been implemented yet + for the "hush" shell. CFG_HUSH_PARSER @@ -2209,6 +2250,24 @@ Low Level (hardware related) configuration options: CFG_POCMR2_MASK_ATTRIB: (MPC826x only) Overrides the default PCI memory map in cpu/mpc8260/pci.c if set. +- CONFIG_SPD_EEPROM + Get DDR timing information from an I2C EEPROM. Common with pluggable + memory modules such as SODIMMs + SPD_EEPROM_ADDRESS + I2C address of the SPD EEPROM + +- CFG_SPD_BUS_NUM + If SPD EEPROM is on an I2C bus other than the first one, specify here. + Note that the value must resolve to something your driver can deal with. + +- CFG_83XX_DDR_USES_CS0 + Only for 83xx systems. If specified, then DDR should be configured + using CS0 and CS1 instead of CS2 and CS3. + +- CFG_83XX_DDR_USES_CS0 + Only for 83xx systems. If specified, then DDR should be configured + using CS0 and CS1 instead of CS2 and CS3. + - CONFIG_ETHER_ON_FEC[12] Define to enable FEC[12] on a 8xx series processor. @@ -3114,11 +3173,11 @@ loadaddr=200000 oftaddr=0x300000 => bootm $loadaddr - $oftaddr ## Booting image at 00200000 ... - Image Name: Linux-2.6.17-dirty - Image Type: PowerPC Linux Kernel Image (gzip compressed) - Data Size: 1029343 Bytes = 1005.2 kB + Image Name: Linux-2.6.17-dirty + Image Type: PowerPC Linux Kernel Image (gzip compressed) + Data Size: 1029343 Bytes = 1005.2 kB Load Address: 00000000 - Entry Point: 00000000 + Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Booting using flat device tree at 0x300000 |