diff options
Diffstat (limited to 'README')
| -rw-r--r-- | README | 398 |
1 files changed, 230 insertions, 168 deletions
@@ -210,7 +210,7 @@ There are two classes of configuration variables: * Configuration _SETTINGS_: These depend on the hardware etc. and should not be meddled with if you don't know what you're doing; they have names beginning with - "CFG_". + "CONFIG_SYS_". Later we will add a configuration tool - probably similar to or even identical to what's used for the Linux kernel. Right now, we have to @@ -284,10 +284,10 @@ The following options need to be configured: - Board flavour: (if CONFIG_MPC8260ADS is defined) CONFIG_ADSTYPE Possible values are: - CFG_8260ADS - original MPC8260ADS - CFG_8266ADS - MPC8266ADS - CFG_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR - CFG_8272ADS - MPC8272ADS + CONFIG_SYS_8260ADS - original MPC8260ADS + CONFIG_SYS_8266ADS - MPC8266ADS + CONFIG_SYS_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR + CONFIG_SYS_8272ADS - MPC8272ADS - MPC824X Family Member (if CONFIG_MPC824X is defined) Define exactly one of @@ -302,28 +302,28 @@ The following options need to be configured: or XTAL/EXTAL) - 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU): - CFG_8xx_CPUCLK_MIN - CFG_8xx_CPUCLK_MAX + CONFIG_SYS_8xx_CPUCLK_MIN + CONFIG_SYS_8xx_CPUCLK_MAX CONFIG_8xx_CPUCLK_DEFAULT See doc/README.MPC866 - CFG_MEASURE_CPUCLK + CONFIG_SYS_MEASURE_CPUCLK Define this to measure the actual CPU clock instead of relying on the correctness of the configured values. Mostly useful for board bringup to make sure the PLL is locked at the intended frequency. Note that this requires a (stable) reference clock (32 kHz - RTC clock or CFG_8XX_XIN) + RTC clock or CONFIG_SYS_8XX_XIN) - Intel Monahans options: - CFG_MONAHANS_RUN_MODE_OSC_RATIO + CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO Defines the Monahans run mode to oscillator ratio. Valid values are 8, 16, 24, 31. The core frequency is this value multiplied by 13 MHz. - CFG_MONAHANS_TURBO_RUN_MODE_RATIO + CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO Defines the Monahans turbo mode to oscillator ratio. Valid values are 1 (default if undefined) and @@ -436,7 +436,7 @@ The following options need to be configured: CONFIG_CONSOLE_CURSOR cursor drawing on/off (requires blink timer cf. i8042.c) - CFG_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c) + CONFIG_SYS_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c) CONFIG_CONSOLE_TIME display time/date info in upper right corner (requires CONFIG_CMD_DATE) @@ -461,8 +461,8 @@ The following options need to be configured: - Console Baudrate: CONFIG_BAUDRATE - in bps Select one of the baudrates listed in - CFG_BAUDRATE_TABLE, see below. - CFG_BRGCLK_PRESCALE, baudrate prescale + CONFIG_SYS_BAUDRATE_TABLE, see below. + CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale - Interrupt driven serial port input: CONFIG_SERIAL_SOFTWARE_FIFO @@ -546,7 +546,7 @@ The following options need to be configured: - Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined) CONFIG_KGDB_BAUDRATE Select one of the baudrates listed in - CFG_BAUDRATE_TABLE, see below. + CONFIG_SYS_BAUDRATE_TABLE, see below. - Monitor Functions: Monitor commands can be included or excluded @@ -673,7 +673,7 @@ The following options need to be configured: CONFIG_RTC_DS164x - use Dallas DS164x RTC CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC - CFG_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337 + CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337 Note that if the RTC uses I2C, then the I2C interface must also be configured. See I2C Support, below. @@ -687,7 +687,7 @@ The following options need to be configured: - Partition Support: CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION - and/or CONFIG_ISO_PARTITION + and/or CONFIG_ISO_PARTITION and/or CONFIG_EFI_PARTITION If IDE or SCSI support is enabled (CONFIG_CMD_IDE or CONFIG_CMD_SCSI) you must configure support for at @@ -711,11 +711,11 @@ The following options need to be configured: CONFIG_LBA48 Set this to enable support for disks larger than 137GB - Also look at CFG_64BIT_LBA ,CFG_64BIT_VSPRINTF and CFG_64BIT_STRTOUL + Also look at CONFIG_SYS_64BIT_LBA ,CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL Whithout these , LBA48 support uses 32bit variables and will 'only' support disks up to 2.1TB. - CFG_64BIT_LBA: + CONFIG_SYS_64BIT_LBA: When enabled, makes the IDE subsystem use 64bit sector addresses. Default is 32bit. @@ -724,12 +724,12 @@ The following options need to be configured: SYM53C8XX SCSI controller; define CONFIG_SCSI_SYM53C8XX to enable it. - CFG_SCSI_MAX_LUN [8], CFG_SCSI_MAX_SCSI_ID [7] and - CFG_SCSI_MAX_DEVICE [CFG_SCSI_MAX_SCSI_ID * - CFG_SCSI_MAX_LUN] can be adjusted to define the + CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and + CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID * + CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the maximum numbers of LUNs, SCSI ID's and target devices. - CFG_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz) + CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz) - NETWORK Support (PCI): CONFIG_E1000 @@ -811,7 +811,7 @@ The following options need to be configured: CONFIG_USB_CONFIG for differential drivers: 0x00001000 for single ended drivers: 0x00005000 - CFG_USB_EVENT_POLL + CONFIG_SYS_USB_EVENT_POLL May be defined to allow interrupt polling instead of using asynchronous interrupts @@ -838,18 +838,18 @@ The following options need to be configured: Define this to have a tty type of device available to talk to the UDC device - CFG_CONSOLE_IS_IN_ENV + CONFIG_SYS_CONSOLE_IS_IN_ENV Define this if you want stdin, stdout &/or stderr to be set to usbtty. mpc8xx: - CFG_USB_EXTC_CLK 0xBLAH + CONFIG_SYS_USB_EXTC_CLK 0xBLAH Derive USB clock from external clock "blah" - - CFG_USB_EXTC_CLK 0x02 + - CONFIG_SYS_USB_EXTC_CLK 0x02 - CFG_USB_BRG_CLK 0xBLAH + CONFIG_SYS_USB_BRG_CLK 0xBLAH Derive USB clock from brgclk - - CFG_USB_BRG_CLK 0x04 + - CONFIG_SYS_USB_BRG_CLK 0x04 If you have a USB-IF assigned VendorID then you may wish to define your own vendor specific values either in BoardName.h @@ -891,16 +891,16 @@ The following options need to be configured: CONFIG_JFFS2_NAND_DEV Define these for a default partition on a NAND device - CFG_JFFS2_FIRST_SECTOR, - CFG_JFFS2_FIRST_BANK, CFG_JFFS2_NUM_BANKS + CONFIG_SYS_JFFS2_FIRST_SECTOR, + CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS Define these for a default partition on a NOR device - CFG_JFFS_CUSTOM_PART + CONFIG_SYS_JFFS_CUSTOM_PART Define this to create an own partition. You have to provide a function struct part_info* jffs2_part_info(int part_num) If you define only one JFFS2 partition you may also want to - #define CFG_JFFS_SINGLE_PART 1 + #define CONFIG_SYS_JFFS_SINGLE_PART 1 to disable the command chpart. This is the default when you have not defined a custom partition @@ -1014,7 +1014,7 @@ The following options need to be configured: 320x240. Black & white. Normally display is black on white background; define - CFG_WHITE_ON_BLACK to get it inverted. + CONFIG_SYS_WHITE_ON_BLACK to get it inverted. - Splash Screen Support: CONFIG_SPLASH_SCREEN @@ -1041,7 +1041,7 @@ The following options need to be configured: compressed images are supported. NOTE: the bzip2 algorithm requires a lot of RAM, so - the malloc area (as defined by CFG_MALLOC_LEN) should + the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should be at least 4MB. CONFIG_LZMA @@ -1065,7 +1065,7 @@ The following options need to be configured: Use the lzmainfo tool to determinate the lc and lp values and then calculate the amount of needed dynamic memory (ensuring - the appropriate CFG_MALLOC_LEN value). + the appropriate CONFIG_SYS_MALLOC_LEN value). - MII/PHY support: CONFIG_PHY_ADDR @@ -1095,8 +1095,11 @@ The following options need to be configured: - Ethernet address: CONFIG_ETHADDR + CONFIG_ETH1ADDR CONFIG_ETH2ADDR CONFIG_ETH3ADDR + CONFIG_ETH4ADDR + CONFIG_ETH5ADDR Define a default value for Ethernet address to use for the respective Ethernet interface, in case this @@ -1279,15 +1282,15 @@ The following options need to be configured: There are several other quantities that must also be defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C. - In both cases you will need to define CFG_I2C_SPEED + In both cases you will need to define CONFIG_SYS_I2C_SPEED to be the frequency (in Hz) at which you wish your i2c bus - to run and CFG_I2C_SLAVE to be the address of this node (ie + to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie the CPU's i2c node address). Now, the u-boot i2c code for the mpc8xx (cpu/mpc8xx/i2c.c) sets the CPU up as a master node and so its address should therefore be cleared to 0 (See, eg, MPC823e User's Manual - p.16-473). So, set CFG_I2C_SLAVE to 0. + p.16-473). So, set CONFIG_SYS_I2C_SLAVE to 0. That's all that's required for CONFIG_HARD_I2C. @@ -1358,7 +1361,7 @@ The following options need to be configured: #define I2C_DELAY udelay(2) - CFG_I2C_INIT_BOARD + CONFIG_SYS_I2C_INIT_BOARD When a board is reset during an i2c bus transfer chips might think that the current transfer is still @@ -1382,7 +1385,7 @@ The following options need to be configured: active. To switch to a different bus, use the 'i2c dev' command. Note that bus numbering is zero-based. - CFG_I2C_NOPROBES + CONFIG_SYS_I2C_NOPROBES This option specifies a list of I2C devices that will be skipped when the 'i2c probe' command is issued (or 'iprobe' using the legacy @@ -1391,31 +1394,31 @@ The following options need to be configured: e.g. #undef CONFIG_I2C_MULTI_BUS - #define CFG_I2C_NOPROBES {0x50,0x68} + #define CONFIG_SYS_I2C_NOPROBES {0x50,0x68} will skip addresses 0x50 and 0x68 on a board with one I2C bus #define CONFIG_I2C_MULTI_BUS - #define CFG_I2C_MULTI_NOPROBES {{0,0x50},{0,0x68},{1,0x54}} + #define CONFIG_SYS_I2C_MULTI_NOPROBES {{0,0x50},{0,0x68},{1,0x54}} will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1 - CFG_SPD_BUS_NUM + CONFIG_SYS_SPD_BUS_NUM If defined, then this indicates the I2C bus number for DDR SPD. If not defined, then U-Boot assumes that SPD is on I2C bus 0. - CFG_RTC_BUS_NUM + CONFIG_SYS_RTC_BUS_NUM If defined, then this indicates the I2C bus number for the RTC. If not defined, then U-Boot assumes that RTC is on I2C bus 0. - CFG_DTT_BUS_NUM + CONFIG_SYS_DTT_BUS_NUM If defined, then this indicates the I2C bus number for the DTT. If not defined, then U-Boot assumes that DTT is on I2C bus 0. - CFG_I2C_DTT_ADDR: + CONFIG_SYS_I2C_DTT_ADDR: If defined, specifies the I2C address of the DTT device. If not defined, then U-Boot uses predefined value for @@ -1426,6 +1429,53 @@ The following options need to be configured: Define this option if you want to use Freescale's I2C driver in drivers/i2c/fsl_i2c.c. + CONFIG_I2C_MUX + + Define this option if you have I2C devices reached over 1 .. n + I2C Muxes like the pca9544a. This option addes a new I2C + Command "i2c bus [muxtype:muxaddr:muxchannel]" which adds a + new I2C Bus to the existing I2C Busses. If you select the + new Bus with "i2c dev", u-bbot sends first the commandos for + the muxes to activate this new "bus". + + CONFIG_I2C_MULTI_BUS must be also defined, to use this + feature! + + Example: + Adding a new I2C Bus reached over 2 pca9544a muxes + The First mux with address 70 and channel 6 + The Second mux with address 71 and channel 4 + + => i2c bus pca9544a:70:6:pca9544a:71:4 + + Use the "i2c bus" command without parameter, to get a list + of I2C Busses with muxes: + + => i2c bus + Busses reached over muxes: + Bus ID: 2 + reached over Mux(es): + pca9544a@70 ch: 4 + Bus ID: 3 + reached over Mux(es): + pca9544a@70 ch: 6 + pca9544a@71 ch: 4 + => + + If you now switch to the new I2C Bus 3 with "i2c dev 3" + u-boot sends First the Commando to the mux@70 to enable + channel 6, and then the Commando to the mux@71 to enable + the channel 4. + + After that, you can use the "normal" i2c commands as + usual, to communicate with your I2C devices behind + the 2 muxes. + + This option is actually implemented for the bitbanging + algorithm in common/soft_i2c.c and for the Hardware I2C + Bus on the MPC8260. But it should be not so difficult + to add this option to other architectures. + - SPI Support: CONFIG_SPI @@ -1479,11 +1529,11 @@ The following options need to be configured: Specify the number of FPGA devices to support. - CFG_FPGA_PROG_FEEDBACK + CONFIG_SYS_FPGA_PROG_FEEDBACK Enable printing of hash marks during FPGA configuration. - CFG_FPGA_CHECK_BUSY + CONFIG_SYS_FPGA_CHECK_BUSY Enable checks on FPGA configuration interface busy status by the configuration function. This option @@ -1495,29 +1545,29 @@ The following options need to be configured: If defined, a function that provides delays in the FPGA configuration driver. - CFG_FPGA_CHECK_CTRLC + CONFIG_SYS_FPGA_CHECK_CTRLC Allow Control-C to interrupt FPGA configuration - CFG_FPGA_CHECK_ERROR + CONFIG_SYS_FPGA_CHECK_ERROR Check for configuration errors during FPGA bitfile loading. For example, abort during Virtex II configuration if the INIT_B line goes low (which indicated a CRC error). - CFG_FPGA_WAIT_INIT + CONFIG_SYS_FPGA_WAIT_INIT Maximum time to wait for the INIT_B line to deassert after PROB_B has been deasserted during a Virtex II FPGA configuration sequence. The default time is 500 ms. - CFG_FPGA_WAIT_BUSY + CONFIG_SYS_FPGA_WAIT_BUSY Maximum time to wait for BUSY to deassert during Virtex II FPGA configuration. The default is 5 ms. - CFG_FPGA_WAIT_CONFIG + CONFIG_SYS_FPGA_WAIT_CONFIG Time to wait after FPGA configuration. The default is 200 ms. @@ -1615,7 +1665,7 @@ The following options need to be configured: for the "hush" shell. - CFG_HUSH_PARSER + CONFIG_SYS_HUSH_PARSER Define this variable to enable the "hush" shell (from Busybox) as command line interpreter, thus enabling @@ -1627,7 +1677,7 @@ The following options need to be configured: with a somewhat smaller memory footprint. - CFG_PROMPT_HUSH_PS2 + CONFIG_SYS_PROMPT_HUSH_PS2 This defines the secondary prompt string, which is printed when the command interpreter needs more input @@ -1699,10 +1749,10 @@ The following options need to be configured: Adding this option adds support for Xilinx SystemACE chips attached via some sort of local bus. The address of the chip must also be defined in the - CFG_SYSTEMACE_BASE macro. For example: + CONFIG_SYS_SYSTEMACE_BASE macro. For example: #define CONFIG_SYSTEMACE - #define CFG_SYSTEMACE_BASE 0xf0000000 + #define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000 When SystemACE support is added, the "ace" device type becomes available to the fat commands, i.e. fatls. @@ -1737,6 +1787,14 @@ The following options need to be configured: example, some LED's) on your board. At the moment, the following checkpoints are implemented: +- Automatic software updates via TFTP server + CONFIG_UPDATE_TFTP + CONFIG_UPDATE_TFTP_CNT_MAX + CONFIG_UPDATE_TFTP_MSEC_MAX + + These options enable and control the auto-update feature; + for a more detailed description refer to doc/README.update. + Legacy uImage format: Arg Where When @@ -1942,53 +2000,53 @@ Modem Support: Configuration Settings: ----------------------- -- CFG_LONGHELP: Defined when you want long help messages included; +- CONFIG_SYS_LONGHELP: Defined when you want long help messages included; undefine this when you're short of memory. -- CFG_PROMPT: This is what U-Boot prints on the console to +- CONFIG_SYS_PROMPT: This is what U-Boot prints on the console to prompt for user input. -- CFG_CBSIZE: Buffer size for input from the Console +- CONFIG_SYS_CBSIZE: Buffer size for input from the Console -- CFG_PBSIZE: Buffer size for Console output +- CONFIG_SYS_PBSIZE: Buffer size for Console output -- CFG_MAXARGS: max. Number of arguments accepted for monitor commands +- CONFIG_SYS_MAXARGS: max. Number of arguments accepted for monitor commands -- CFG_BARGSIZE: Buffer size for Boot Arguments which are passed to +- CONFIG_SYS_BARGSIZE: Buffer size for Boot Arguments which are passed to the application (usually a Linux kernel) when it is booted -- CFG_BAUDRATE_TABLE: +- CONFIG_SYS_BAUDRATE_TABLE: List of legal baudrate settings for this board. -- CFG_CONSOLE_INFO_QUIET +- CONFIG_SYS_CONSOLE_INFO_QUIET Suppress display of console information at boot. -- CFG_CONSOLE_IS_IN_ENV +- CONFIG_SYS_CONSOLE_IS_IN_ENV If the board specific function extern int overwrite_console (void); returns 1, the stdin, stderr and stdout are switched to the serial port, else the settings in the environment are used. -- CFG_CONSOLE_OVERWRITE_ROUTINE +- CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE Enable the call to overwrite_console(). -- CFG_CONSOLE_ENV_OVERWRITE +- CONFIG_SYS_CONSOLE_ENV_OVERWRITE Enable overwrite of previous console environment settings. -- CFG_MEMTEST_START, CFG_MEMTEST_END: +- CONFIG_SYS_MEMTEST_START, CONFIG_SYS_MEMTEST_END: Begin and End addresses of the area used by the simple memory test. -- CFG_ALT_MEMTEST: +- CONFIG_SYS_ALT_MEMTEST: Enable an alternate, more extensive memory test. -- CFG_MEMTEST_SCRATCH: +- CONFIG_SYS_MEMTEST_SCRATCH: Scratch address used by the alternate memory test You only need to set this if address zero isn't writeable -- CFG_MEM_TOP_HIDE (PPC only): - If CFG_MEM_TOP_HIDE is defined in the board config header, +- CONFIG_SYS_MEM_TOP_HIDE (PPC only): + If CONFIG_SYS_MEM_TOP_HIDE is defined in the board config header, this specified memory area will get subtracted from the top (end) of RAM and won't get "touched" at all by U-Boot. By fixing up gd->ram_size the Linux kernel should gets passed @@ -2008,75 +2066,75 @@ Configuration Settings: non page size aligned address and this could cause major problems. -- CFG_TFTP_LOADADDR: +- CONFIG_SYS_TFTP_LOADADDR: Default load address for network file downloads -- CFG_LOADS_BAUD_CHANGE: +- CONFIG_SYS_LOADS_BAUD_CHANGE: Enable temporary baudrate change while serial download -- CFG_SDRAM_BASE: +- CONFIG_SYS_SDRAM_BASE: Physical start address of SDRAM. _Must_ be 0 here. -- CFG_MBIO_BASE: +- CONFIG_SYS_MBIO_BASE: Physical start address of Motherboard I/O (if using a Cogent motherboard) -- CFG_FLASH_BASE: +- CONFIG_SYS_FLASH_BASE: Physical start address of Flash memory. -- CFG_MONITOR_BASE: +- CONFIG_SYS_MONITOR_BASE: Physical start address of boot monitor code (set by make config files to be same as the text base address (TEXT_BASE) used when linking) - same as - CFG_FLASH_BASE when booting from flash. + CONFIG_SYS_FLASH_BASE when booting from flash. -- CFG_MONITOR_LEN: +- CONFIG_SYS_MONITOR_LEN: Size of memory reserved for monitor code, used to determine _at_compile_time_ (!) if the environment is embedded within the U-Boot image, or in a separate flash sector. -- CFG_MALLOC_LEN: +- CONFIG_SYS_MALLOC_LEN: Size of DRAM reserved for malloc() use. -- CFG_BOOTM_LEN: +- CONFIG_SYS_BOOTM_LEN: Normally compressed uImages are limited to an uncompressed size of 8 MBytes. If this is not enough, - you can define CFG_BOOTM_LEN in your board config file + you can define CONFIG_SYS_BOOTM_LEN in your board config file to adjust this setting to your needs. -- CFG_BOOTMAPSZ: +- CONFIG_SYS_BOOTMAPSZ: Maximum size of memory mapped by the startup code of the Linux kernel; all data that must be processed by the Linux kernel (bd_info, boot arguments, FDT blob if used) must be put below this limit, unless "bootm_low" enviroment variable is defined and non-zero. In such case all data for the Linux kernel must be between "bootm_low" - and "bootm_low" + CFG_BOOTMAPSZ. + and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. -- CFG_MAX_FLASH_BANKS: +- CONFIG_SYS_MAX_FLASH_BANKS: Max number of Flash memory banks -- CFG_MAX_FLASH_SECT: +- CONFIG_SYS_MAX_FLASH_SECT: Max number of sectors on a Flash chip -- CFG_FLASH_ERASE_TOUT: +- CONFIG_SYS_FLASH_ERASE_TOUT: Timeout for Flash erase operations (in ms) -- CFG_FLASH_WRITE_TOUT: +- CONFIG_SYS_FLASH_WRITE_TOUT: Timeout for Flash write operations (in ms) -- CFG_FLASH_LOCK_TOUT +- CONFIG_SYS_FLASH_LOCK_TOUT Timeout for Flash set sector lock bit operation (in ms) -- CFG_FLASH_UNLOCK_TOUT +- CONFIG_SYS_FLASH_UNLOCK_TOUT Timeout for Flash clear lock bits operation (in ms) -- CFG_FLASH_PROTECTION +- CONFIG_SYS_FLASH_PROTECTION If defined, hardware flash sectors protection is used instead of U-Boot software protection. -- CFG_DIRECT_FLASH_TFTP: +- CONFIG_SYS_DIRECT_FLASH_TFTP: Enable TFTP transfers directly to flash memory; without this option such a download has to be @@ -2089,7 +2147,7 @@ Configuration Settings: too limited to allow for a temporary copy of the downloaded image) this option may be very useful. -- CFG_FLASH_CFI: +- CONFIG_SYS_FLASH_CFI: Define if the flash driver uses extra elements in the common flash structure for storing flash geometry. @@ -2097,14 +2155,14 @@ Configuration Settings: This option also enables the building of the cfi_flash driver in the drivers directory -- CFG_FLASH_USE_BUFFER_WRITE +- CONFIG_SYS_FLASH_USE_BUFFER_WRITE Use buffered writes to flash. - CONFIG_FLASH_SPANSION_S29WS_N s29ws-n MirrorBit flash has non-standard addresses for buffered write commands. -- CFG_FLASH_QUIET_TEST +- CONFIG_SYS_FLASH_QUIET_TEST If this option is defined, the common CFI flash doesn't print it's warning upon not recognized FLASH banks. This is useful, if some of the configured banks are only @@ -2115,7 +2173,7 @@ Configuration Settings: digits and dots. Recommended value: 45 (9..1) for 80 column displays, 15 (3..1) for 40 column displays. -- CFG_RX_ETH_BUFFER: +- CONFIG_SYS_RX_ETH_BUFFER: Defines the number of Ethernet receive buffers. On some Ethernet controllers it is recommended to set this value to 8 or even higher (EEPRO100 or 405 EMAC), since all @@ -2150,7 +2208,7 @@ following configurations: type flash chips the second sector can be used: the offset for this sector is given here. - CONFIG_ENV_OFFSET is used relative to CFG_FLASH_BASE. + CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE. - CONFIG_ENV_ADDR: @@ -2233,24 +2291,24 @@ to save the current settings. These two #defines specify the offset and size of the environment area within the total memory of your EEPROM. - - CFG_I2C_EEPROM_ADDR: + - CONFIG_SYS_I2C_EEPROM_ADDR: If defined, specified the chip address of the EEPROM device. The default address is zero. - - CFG_EEPROM_PAGE_WRITE_BITS: + - CONFIG_SYS_EEPROM_PAGE_WRITE_BITS: If defined, the number of bits used to address bytes in a single page in the EEPROM device. A 64 byte page, for example would require six bits. - - CFG_EEPROM_PAGE_WRITE_DELAY_MS: + - CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS: If defined, the number of milliseconds to delay between page writes. The default is zero milliseconds. - - CFG_I2C_EEPROM_ADDR_LEN: + - CONFIG_SYS_I2C_EEPROM_ADDR_LEN: The length in bytes of the EEPROM memory array address. Note that this is NOT the chip address length! - - CFG_I2C_EEPROM_ADDR_OVERFLOW: + - CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW: EEPROM chips that implement "address overflow" are ones like Catalyst 24WC04/08/16 which has 9/10/11 bits of address and the extra bits end up in the "chip address" bit @@ -2261,7 +2319,7 @@ to save the current settings. still be one byte because the extra address bits are hidden in the chip address. - - CFG_EEPROM_SIZE: + - CONFIG_SYS_EEPROM_SIZE: The size in bytes of the EEPROM device. @@ -2300,7 +2358,7 @@ to save the current settings. to a block boundary, and CONFIG_ENV_SIZE must be a multiple of the NAND devices block size. -- CFG_SPI_INIT_OFFSET +- CONFIG_SYS_SPI_INIT_OFFSET Defines offset to the initial SPI buffer area in DPRAM. The area is used at an early stage (ROM part) if the environment @@ -2326,29 +2384,29 @@ Note: once the monitor has been relocated, then it will complain if the default environment is used; a new CRC is computed as soon as you use the "saveenv" command to store a valid environment. -- CFG_FAULT_ECHO_LINK_DOWN: +- CONFIG_SYS_FAULT_ECHO_LINK_DOWN: Echo the inverted Ethernet link state to the fault LED. - Note: If this option is active, then CFG_FAULT_MII_ADDR + Note: If this option is active, then CONFIG_SYS_FAULT_MII_ADDR also needs to be defined. -- CFG_FAULT_MII_ADDR: +- CONFIG_SYS_FAULT_MII_ADDR: MII address of the PHY to check for the Ethernet link state. -- CFG_64BIT_VSPRINTF: +- CONFIG_SYS_64BIT_VSPRINTF: Makes vsprintf (and all *printf functions) support printing of 64bit values by using the L quantifier -- CFG_64BIT_STRTOUL: +- CONFIG_SYS_64BIT_STRTOUL: Adds simple_strtoull that returns a 64bit value Low Level (hardware related) configuration options: --------------------------------------------------- -- CFG_CACHELINE_SIZE: +- CONFIG_SYS_CACHELINE_SIZE: Cache Line Size of the CPU. -- CFG_DEFAULT_IMMR: +- CONFIG_SYS_DEFAULT_IMMR: Default address of the IMMR after system reset. Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU, @@ -2356,36 +2414,36 @@ Low Level (hardware related) configuration options: the IMMR register after a reset. - Floppy Disk Support: - CFG_FDC_DRIVE_NUMBER + CONFIG_SYS_FDC_DRIVE_NUMBER the default drive number (default value 0) - CFG_ISA_IO_STRIDE + CONFIG_SYS_ISA_IO_STRIDE defines the spacing between FDC chipset registers (default value 1) - CFG_ISA_IO_OFFSET + CONFIG_SYS_ISA_IO_OFFSET defines the offset of register from address. It depends on which part of the data bus is connected to the FDC chipset. (default value 0) - If CFG_ISA_IO_STRIDE CFG_ISA_IO_OFFSET and - CFG_FDC_DRIVE_NUMBER are undefined, they take their + If CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_IO_OFFSET and + CONFIG_SYS_FDC_DRIVE_NUMBER are undefined, they take their default value. - if CFG_FDC_HW_INIT is defined, then the function + if CONFIG_SYS_FDC_HW_INIT is defined, then the function fdc_hw_init() is called at the beginning of the FDC setup. fdc_hw_init() must be provided by the board source code. It is used to make hardware dependant initializations. -- CFG_IMMR: Physical address of the Internal Memory. +- CONFIG_SYS_IMMR: Physical address of the Internal Memory. DO NOT CHANGE unless you know exactly what you're doing! (11-4) [MPC8xx/82xx systems only] -- CFG_INIT_RAM_ADDR: +- CONFIG_SYS_INIT_RAM_ADDR: Start address of memory area that can be used for initial data and stack; please note that this must be @@ -2400,91 +2458,91 @@ Low Level (hardware related) configuration options: - MPC824X: data cache - PPC4xx: data cache -- CFG_GBL_DATA_OFFSET: +- CONFIG_SYS_GBL_DATA_OFFSET: Offset of the initial data structure in the memory - area defined by CFG_INIT_RAM_ADDR. Usually - CFG_GBL_DATA_OFFSET is chosen such that the initial + area defined by CONFIG_SYS_INIT_RAM_ADDR. Usually + CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial data is located at the end of the available space - (sometimes written as (CFG_INIT_RAM_END - - CFG_INIT_DATA_SIZE), and the initial stack is just - below that area (growing from (CFG_INIT_RAM_ADDR + - CFG_GBL_DATA_OFFSET) downward. + (sometimes written as (CONFIG_SYS_INIT_RAM_END - + CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just + below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR + + CONFIG_SYS_GBL_DATA_OFFSET) downward. Note: On the MPC824X (or other systems that use the data cache for initial memory) the address chosen for - CFG_INIT_RAM_ADDR is basically arbitrary - it must + CONFIG_SYS_INIT_RAM_ADDR is basically arbitrary - it must point to an otherwise UNUSED address space between the top of RAM and the start of the PCI space. -- CFG_SIUMCR: SIU Module Configuration (11-6) +- CONFIG_SYS_SIUMCR: SIU Module Configuration (11-6) -- CFG_SYPCR: System Protection Control (11-9) +- CONFIG_SYS_SYPCR: System Protection Control (11-9) -- CFG_TBSCR: Time Base Status and Control (11-26) +- CONFIG_SYS_TBSCR: Time Base Status and Control (11-26) -- CFG_PISCR: Periodic Interrupt Status and Control (11-31) +- CONFIG_SYS_PISCR: Periodic Interrupt Status and Control (11-31) -- CFG_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30) +- CONFIG_SYS_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30) -- CFG_SCCR: System Clock and reset Control Register (15-27) +- CONFIG_SYS_SCCR: System Clock and reset Control Register (15-27) -- CFG_OR_TIMING_SDRAM: +- CONFIG_SYS_OR_TIMING_SDRAM: SDRAM timing -- CFG_MAMR_PTA: +- CONFIG_SYS_MAMR_PTA: periodic timer for refresh -- CFG_DER: Debug Event Register (37-47) +- CONFIG_SYS_DER: Debug Event Register (37-47) -- FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CFG_REMAP_OR_AM, - CFG_PRELIM_OR_AM, CFG_OR_TIMING_FLASH, CFG_OR0_REMAP, - CFG_OR0_PRELIM, CFG_BR0_PRELIM, CFG_OR1_REMAP, CFG_OR1_PRELIM, - CFG_BR1_PRELIM: +- FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CONFIG_SYS_REMAP_OR_AM, + CONFIG_SYS_PRELIM_OR_AM, CONFIG_SYS_OR_TIMING_FLASH, CONFIG_SYS_OR0_REMAP, + CONFIG_SYS_OR0_PRELIM, CONFIG_SYS_BR0_PRELIM, CONFIG_SYS_OR1_REMAP, CONFIG_SYS_OR1_PRELIM, + CONFIG_SYS_BR1_PRELIM: Memory Controller Definitions: BR0/1 and OR0/1 (FLASH) - SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE, - CFG_OR_TIMING_SDRAM, CFG_OR2_PRELIM, CFG_BR2_PRELIM, - CFG_OR3_PRELIM, CFG_BR3_PRELIM: + CONFIG_SYS_OR_TIMING_SDRAM, CONFIG_SYS_OR2_PRELIM, CONFIG_SYS_BR2_PRELIM, + CONFIG_SYS_OR3_PRELIM, CONFIG_SYS_BR3_PRELIM: Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM) -- CFG_MAMR_PTA, CFG_MPTPR_2BK_4K, CFG_MPTPR_1BK_4K, CFG_MPTPR_2BK_8K, - CFG_MPTPR_1BK_8K, CFG_MAMR_8COL, CFG_MAMR_9COL: +- CONFIG_SYS_MAMR_PTA, CONFIG_SYS_MPTPR_2BK_4K, CONFIG_SYS_MPTPR_1BK_4K, CONFIG_SYS_MPTPR_2BK_8K, + CONFIG_SYS_MPTPR_1BK_8K, CONFIG_SYS_MAMR_8COL, CONFIG_SYS_MAMR_9COL: Machine Mode Register and Memory Periodic Timer Prescaler definitions (SDRAM timing) -- CFG_I2C_UCODE_PATCH, CFG_I2C_DPMEM_OFFSET [0x1FC0]: +- CONFIG_SYS_I2C_UCODE_PATCH, CONFIG_SYS_I2C_DPMEM_OFFSET [0x1FC0]: enable I2C microcode relocation patch (MPC8xx); define relocation offset in DPRAM [DSP2] -- CFG_SMC_UCODE_PATCH, CFG_SMC_DPMEM_OFFSET [0x1FC0]: +- CONFIG_SYS_SMC_UCODE_PATCH, CONFIG_SYS_SMC_DPMEM_OFFSET [0x1FC0]: enable SMC microcode relocation patch (MPC8xx); define relocation offset in DPRAM [SMC1] -- CFG_SPI_UCODE_PATCH, CFG_SPI_DPMEM_OFFSET [0x1FC0]: +- CONFIG_SYS_SPI_UCODE_PATCH, CONFIG_SYS_SPI_DPMEM_OFFSET [0x1FC0]: enable SPI microcode relocation patch (MPC8xx); define relocation offset in DPRAM [SCC4] -- CFG_USE_OSCCLK: +- CONFIG_SYS_USE_OSCCLK: Use OSCM clock mode on MBX8xx board. Be careful, wrong setting might damage your board. Read doc/README.MBX before setting this variable! -- CFG_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only) +- CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only) Offset of the bootmode word in DPRAM used by post (Power On Self Tests). This definition overrides #define'd default value in commproc.h resp. cpm_8260.h. -- CFG_PCI_SLV_MEM_LOCAL, CFG_PCI_SLV_MEM_BUS, CFG_PICMR0_MASK_ATTRIB, - CFG_PCI_MSTR0_LOCAL, CFG_PCIMSK0_MASK, CFG_PCI_MSTR1_LOCAL, - CFG_PCIMSK1_MASK, CFG_PCI_MSTR_MEM_LOCAL, CFG_PCI_MSTR_MEM_BUS, - CFG_CPU_PCI_MEM_START, CFG_PCI_MSTR_MEM_SIZE, CFG_POCMR0_MASK_ATTRIB, - CFG_PCI_MSTR_MEMIO_LOCAL, CFG_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START, - CFG_PCI_MSTR_MEMIO_SIZE, CFG_POCMR1_MASK_ATTRIB, CFG_PCI_MSTR_IO_LOCAL, - CFG_PCI_MSTR_IO_BUS, CFG_CPU_PCI_IO_START, CFG_PCI_MSTR_IO_SIZE, - CFG_POCMR2_MASK_ATTRIB: (MPC826x only) +- CONFIG_SYS_PCI_SLV_MEM_LOCAL, CONFIG_SYS_PCI_SLV_MEM_BUS, CONFIG_SYS_PICMR0_MASK_ATTRIB, + CONFIG_SYS_PCI_MSTR0_LOCAL, CONFIG_SYS_PCIMSK0_MASK, CONFIG_SYS_PCI_MSTR1_LOCAL, + CONFIG_SYS_PCIMSK1_MASK, CONFIG_SYS_PCI_MSTR_MEM_LOCAL, CONFIG_SYS_PCI_MSTR_MEM_BUS, + CONFIG_SYS_CPU_PCI_MEM_START, CONFIG_SYS_PCI_MSTR_MEM_SIZE, CONFIG_SYS_POCMR0_MASK_ATTRIB, + CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL, CONFIG_SYS_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START, + CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL, + CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE, + CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only) Overrides the default PCI memory map in cpu/mpc8260/pci.c if set. - CONFIG_SPD_EEPROM @@ -2494,16 +2552,16 @@ Low Level (hardware related) configuration options: SPD_EEPROM_ADDRESS I2C address of the SPD EEPROM -- CFG_SPD_BUS_NUM +- CONFIG_SYS_SPD_BUS_NUM If SPD EEPROM is on an I2C bus other than the first one, specify here. Note that the value must resolve to something your driver can deal with. -- CFG_83XX_DDR_USES_CS0 +- CONFIG_SYS_83XX_DDR_USES_CS0 Only for 83xx systems. If specified, then DDR should be configured using CS0 and CS1 instead of CS2 and CS3. -- CFG_83XX_DDR_USES_CS0 +- CONFIG_SYS_83XX_DDR_USES_CS0 Only for 83xx systems. If specified, then DDR should be configured using CS0 and CS1 instead of CS2 and CS3. @@ -2803,7 +2861,7 @@ Some configuration options can be set using Environment Variables: for use by the bootm command. See also "bootm_size" environment variable. Address defined by "bootm_low" is also the base of the initial memory mapping for the Linux - kernel -- see the description of CFG_BOOTMAPSZ. + kernel -- see the description of CONFIG_SYS_BOOTMAPSZ. bootm_size - Memory range available for image processing in the bootm command can be restricted. This variable is given as @@ -2811,6 +2869,10 @@ Some configuration options can be set using Environment Variables: allowed for use by the bootm command. See also "bootm_low" environment variable. + updatefile - Location of the software update file on a TFTP server, used + by the automatic software update feature. Please refer to + documentation in doc/README.update for more details. + autoload - if set to "no" (any string beginning with 'n'), "bootp" will just load perform a lookup of the configuration from the BOOTP server, but not try to @@ -2847,7 +2909,7 @@ Some configuration options can be set using Environment Variables: is usually what you want since it allows for maximum initrd size. If for some reason you want to make sure that the initrd image is loaded below the - CFG_BOOTMAPSZ limit, you can set this environment + CONFIG_SYS_BOOTMAPSZ limit, you can set this environment variable to a value of "no" or "off" or "0". Alternatively, you can set it to a maximum upper address to use (U-Boot will still check that it @@ -3121,7 +3183,7 @@ Just make sure your machine specific header file (for instance include/asm-ppc/tqm8xx.h) includes the same definition of the Board Information structure as we define in include/asm-<arch>/u-boot.h, and make sure that your definition of IMAP_ADDR uses the same value -as your U-Boot configuration in CFG_IMMR. +as your U-Boot configuration in CONFIG_SYS_IMMR. Configuring the Linux kernel: @@ -3668,7 +3730,7 @@ locked as (mis-) used as memory, etc. cause you grief during the initial boot! It is frequently not used. - CFG_INIT_RAM_ADDR should be somewhere that won't interfere + CONFIG_SYS_INIT_RAM_ADDR should be somewhere that won't interfere with your processor/board/system design. The default value you will find in any recent u-boot distribution in walnut.h should work for you. I'd set it to a value larger @@ -3765,7 +3827,7 @@ U-Boot is installed in the first 128 kB of the first Flash bank (on TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After booting and sizing and initializing DRAM, the code relocates itself to the upper end of DRAM. Immediately below the U-Boot code some -memory is reserved for use by malloc() [see CFG_MALLOC_LEN +memory is reserved for use by malloc() [see CONFIG_SYS_MALLOC_LEN configuration setting]. Below that, a structure with global Board Info data is placed, followed by the stack (growing downward). |