summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--board/esd/meesc/meesc.c112
-rw-r--r--include/configs/meesc.h10
2 files changed, 62 insertions, 60 deletions
diff --git a/board/esd/meesc/meesc.c b/board/esd/meesc/meesc.c
index 694bd74..58ef7be 100644
--- a/board/esd/meesc/meesc.c
+++ b/board/esd/meesc/meesc.c
@@ -3,7 +3,7 @@
* Stelian Pop <stelian.pop@leadtechdesign.com>
* Lead Tech Design <www.leadtechdesign.com>
*
- * (C) Copyright 2009
+ * (C) Copyright 2009-2010
* Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
* esd electronic system design gmbh <www.esd.eu>
*
@@ -28,13 +28,13 @@
#include <common.h>
#include <asm/arch/at91sam9263.h>
-#include <asm/arch/at91sam9_matrix.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/at91_pmc.h>
#include <asm/arch/at91_rstc.h>
+#include <asm/arch/at91_matrix.h>
+#include <asm/arch/at91_pio.h>
#include <asm/arch/clk.h>
-#include <asm/arch/gpio.h>
#include <asm/arch/hardware.h>
#include <asm/arch/io.h>
#include <netdev.h>
@@ -52,10 +52,10 @@ int get_hw_rev(void)
if (hw_rev >= 0)
return hw_rev;
- hw_rev = at91_get_gpio_value(AT91_PIN_PB19);
- hw_rev |= at91_get_gpio_value(AT91_PIN_PB20) << 1;
- hw_rev |= at91_get_gpio_value(AT91_PIN_PB21) << 2;
- hw_rev |= at91_get_gpio_value(AT91_PIN_PB22) << 3;
+ hw_rev = at91_get_pio_value(AT91_PIO_PORTB, 19);
+ hw_rev |= at91_get_pio_value(AT91_PIO_PORTB, 20) << 1;
+ hw_rev |= at91_get_pio_value(AT91_PIO_PORTB, 21) << 2;
+ hw_rev |= at91_get_pio_value(AT91_PIO_PORTB, 22) << 3;
if (hw_rev == 15)
hw_rev = 0;
@@ -67,44 +67,44 @@ int get_hw_rev(void)
static void meesc_nand_hw_init(void)
{
unsigned long csa;
+ at91_smc_t *smc = (at91_smc_t *) AT91_SMC0_BASE;
+ at91_matrix_t *matrix = (at91_matrix_t *) AT91_MATRIX_BASE;
/* Enable CS3 */
- csa = at91_sys_read(AT91_MATRIX_EBI0CSA);
- at91_sys_write(AT91_MATRIX_EBI0CSA,
- csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA);
+ csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A;
+ writel(csa, &matrix->csa[0]);
/* Configure SMC CS3 for NAND/SmartMedia */
- at91_sys_write(AT91_SMC_SETUP(3),
- AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) |
- AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
- at91_sys_write(AT91_SMC_PULSE(3),
- AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) |
- AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
- at91_sys_write(AT91_SMC_CYCLE(3),
- AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
- at91_sys_write(AT91_SMC_MODE(3),
- AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
- AT91_SMC_EXNWMODE_DISABLE |
-#ifdef CONFIG_SYS_NAND_DBW_16
- AT91_SMC_DBW_16 |
-#else /* CONFIG_SYS_NAND_DBW_8 */
- AT91_SMC_DBW_8 |
-#endif
- AT91_SMC_TDF_(2));
+ writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
+ AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
+ &smc->cs[3].setup);
+
+ writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
+ AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
+ &smc->cs[3].pulse);
+
+ writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
+ &smc->cs[3].cycle);
+ writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+ AT91_SMC_MODE_EXNW_DISABLE |
+ AT91_SMC_MODE_DBW_8 |
+ AT91_SMC_MODE_TDF_CYCLE(2),
+ &smc->cs[3].mode);
/* Configure RDY/BSY */
- at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
+ at91_set_pio_input(CONFIG_SYS_NAND_READY_PIN, 1);
/* Enable NandFlash */
- at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
+ at91_set_pio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
}
#endif /* CONFIG_CMD_NAND */
#ifdef CONFIG_MACB
static void meesc_macb_hw_init(void)
{
+ at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE;
/* Enable clock */
- at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9263_ID_EMAC);
+ writel(1 << AT91SAM9263_ID_EMAC, &pmc->pcer);
at91_macb_hw_init();
}
#endif
@@ -117,26 +117,27 @@ static void meesc_macb_hw_init(void)
*/
static void meesc_ethercat_hw_init(void)
{
+ at91_smc_t *smc1 = (at91_smc_t *) AT91_SMC1_BASE;
+
/* Configure SMC EBI1_CS0 for EtherCAT */
- at91_sys_write(AT91_SMC1_SETUP(0),
- AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0) |
- AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0));
- at91_sys_write(AT91_SMC1_PULSE(0),
- AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(9) |
- AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(9));
- at91_sys_write(AT91_SMC1_CYCLE(0),
- AT91_SMC_NWECYCLE_(10) | AT91_SMC_NRDCYCLE_(5));
+ writel(AT91_SMC_SETUP_NWE(0) | AT91_SMC_SETUP_NCS_WR(0) |
+ AT91_SMC_SETUP_NRD(0) | AT91_SMC_SETUP_NCS_RD(0),
+ &smc1->cs[0].setup);
+ writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(9) |
+ AT91_SMC_PULSE_NRD(5) | AT91_SMC_PULSE_NCS_RD(9),
+ &smc1->cs[0].pulse);
+ writel(AT91_SMC_CYCLE_NWE(10) | AT91_SMC_CYCLE_NRD(6),
+ &smc1->cs[0].cycle);
/*
* Configure behavior at external wait signal, byte-select mode, 16 bit
* data bus width, none data float wait states and TDF optimization
*/
- at91_sys_write(AT91_SMC1_MODE(0),
- AT91_SMC_READMODE | AT91_SMC_EXNWMODE_READY |
- AT91_SMC_BAT_SELECT | AT91_SMC_DBW_16 | AT91_SMC_TDF_(0) |
- AT91_SMC_TDFMODE);
+ writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_EXNW_READY |
+ AT91_SMC_MODE_DBW_16 | AT91_SMC_MODE_TDF_CYCLE(0) |
+ AT91_SMC_MODE_TDF, &smc1->cs[0].mode);
/* Configure RDY/BSY */
- at91_set_B_periph(AT91_PIN_PE20, 0); /* EBI1_NWAIT */
+ at91_set_b_periph(AT91_PIO_PORTE, 20, 0); /* EBI1_NWAIT */
}
int dram_init(void)
@@ -150,7 +151,7 @@ int board_eth_init(bd_t *bis)
{
int rc = 0;
#ifdef CONFIG_MACB
- rc = macb_eth_initialize(0, (void *)AT91SAM9263_BASE_EMAC, 0x00);
+ rc = macb_eth_initialize(0, (void *)AT91_EMAC_BASE, 0x00);
#endif
return rc;
}
@@ -175,7 +176,7 @@ int checkboard(void)
gd->bd->bi_arch_number = MACH_TYPE_ETHERCAN2;
puts("Board: EtherCAN/2 Gateway");
/* switch on LED1D */
- at91_set_gpio_output(AT91_PIN_PB12, 1);
+ at91_set_pio_output(AT91_PIO_PORTB, 12, 1);
break;
default:
/* assume, no ET1100 present, arch number of EtherCAN/2-Board */
@@ -222,8 +223,9 @@ u32 get_board_rev(void)
#ifdef CONFIG_MISC_INIT_R
int misc_init_r(void)
{
- char *str;
- char buf[32];
+ char *str;
+ char buf[32];
+ at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE;
/*
* Normally the processor clock has a divisor of 2.
@@ -231,10 +233,9 @@ int misc_init_r(void)
* Check the user has set environment mdiv to 4 to change the divisor.
*/
if ((str = getenv("mdiv")) && (strcmp(str, "4") == 0)) {
- at91_sys_write(AT91_PMC_MCKR,
- (at91_sys_read(AT91_PMC_MCKR) & ~AT91_PMC_MDIV) |
- AT91SAM9_PMC_MDIV_4);
- at91_clock_init(0);
+ writel((readl(&pmc->mckr) & ~AT91_PMC_MDIV) |
+ AT91SAM9_PMC_MDIV_4, &pmc->mckr);
+ at91_clock_init(CONFIG_SYS_AT91_MAIN_CLOCK);
serial_setbrg();
/* Notify the user that the clock is not default */
printf("Setting master clock to %s MHz\n",
@@ -247,10 +248,13 @@ int misc_init_r(void)
int board_init(void)
{
+ at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE;
+
/* Peripheral Clock Enable Register */
- at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9263_ID_PIOA |
- 1 << AT91SAM9263_ID_PIOB |
- 1 << AT91SAM9263_ID_PIOCDE);
+ writel(1 << AT91SAM9263_ID_PIOA |
+ 1 << AT91SAM9263_ID_PIOB |
+ 1 << AT91SAM9263_ID_PIOCDE,
+ &pmc->pcer);
/* initialize ET1100 Controller */
meesc_ethercat_hw_init();
diff --git a/include/configs/meesc.h b/include/configs/meesc.h
index dad0bef..eaea1cd 100644
--- a/include/configs/meesc.h
+++ b/include/configs/meesc.h
@@ -31,14 +31,12 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_AT91_LEGACY
-
/* Common stuff */
-#define CONFIG_SYS_HZ 1000 /* decrementer freq */
#define CONFIG_MEESC 1 /* Board is esd MEESC */
#define CONFIG_ARM926EJS 1 /* This is an ARM926EJS Core */
#define CONFIG_AT91SAM9263 1 /* It's an AT91SAM9263 SoC */
#define CONFIG_SYS_AT91_MAIN_CLOCK 16000000/* 16.0 MHz crystal */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq */
#define CONFIG_DISPLAY_BOARDINFO 1
#define CONFIG_DISPLAY_CPUINFO 1 /* display cpu info and speed */
#define CONFIG_PREBOOT /* enable preboot variable */
@@ -122,9 +120,9 @@
#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
/* our CLE is AD22 */
#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
-#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PD15
-#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PA22
-
+#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIO_PORTD, 15
+#define CONFIG_SYS_NAND_READY_PIN AT91_PIO_PORTA, 22
+#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
#endif
/* Ethernet */